Still having trouble with a new uboot install November 18, 2012 07:59PM |
Registered: 11 years ago Posts: 20 |
baudrate=115200 loads_echo=0 rootpath=/mnt/ARM_FS/ netmask=255.255.0.0 run_diag=yes stdin=serial stdout=serial stderr=serial console=console=ttyS0,115200 mainlineLinux=no CASset=min enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes MALLOC_len=1 ethprime=egiga0 netbsd_en=no vxworks_en=no bootargs_end=:::DB88FXX81:eth0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; bootdelay=3 disaMvPnp=no ethaddr=00:50:43:b4:1a:2e ethmtu=1500 usb0Mode=host nandEcc=1bit netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no enaAutoRecovery=yes pcieTune=no ethact=egiga0 filesize=33AA2E bootargs=console=ttyS0,115200 root=/dev/ram0 rw ramdisk=0x01100000,8M install_type=nand bootargs_root=ubi.mtd=2,2048 root=ubi0:rootfs rootfstype=ubifs init=/linuxrc console2=console=ttyS0,115200 bootcmd=nand read.e 0x800000 0x100000 0x600000; setenv bootargs $(console2) $(bootargs_root); bootm 0x800000 arcNumber=3089 serverip=192.168.0.89 ipaddr=192.168.0.94 if_netconsole=ping $serverip start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; preboot=run if_netconsole start_netconsole
Re: Still having trouble with a new uboot install November 19, 2012 12:39AM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: Still having trouble with a new uboot install November 19, 2012 01:48AM |
Registered: 11 years ago Posts: 20 |
Re: Still having trouble with a new uboot install November 19, 2012 04:29AM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: Still having trouble with a new uboot install November 19, 2012 08:44AM |
Registered: 11 years ago Posts: 20 |
Re: Still having trouble with a new uboot install November 19, 2012 04:11PM |
Admin Registered: 13 years ago Posts: 18,495 |
You are already running the latest uBoot. Would you like to reset the uBoot environment? [N/y] y
Re: Still having trouble with a new uboot install November 19, 2012 07:53PM |
Registered: 11 years ago Posts: 20 |
Re: Still having trouble with a new uboot install November 20, 2012 09:27AM |
Registered: 11 years ago Posts: 20 |
ethact=egiga0 bootdelay=3 baudrate=115200 arcNumber=2097 mainlineLinux=yes console=ttyS0,115200 led_init=green blinking led_exit=green off led_error=orange blinking mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) mtdids=nand0=orion_nand partition=nand0,2 stdin=serial stdout=serial stderr=serial rescue_installed=0 rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi ubifs_mtd=3 ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done usb_scan_list=1 2 3 4 usb_scan_1=usb=0:1 dev=sda1 usb_scan_2=usb=1:1 dev=sdb1 usb_scan_3=usb=2:1 dev=sdc1 usb_scan_4=usb=3:1 dev=sdd1 usb_init=run usb_scan usb_device=0:1 usb_root=/dev/sda1 usb_rootfstype=ext2 usb_rootdelay=10 usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset
Re: Still having trouble with a new uboot install November 20, 2012 10:44AM |
Registered: 11 years ago Posts: 20 |
rescue:/tmp# ./install_uboot_mtd0.sh !!!!!! DANGER DANGER DANGER DANGER DANGER DANGER !!!!!! If you lose power to your device while running this script, it could be left in an unusable state. This script will replace the bootloader on /dev/mtd0. This installer will only work on the following devices: Seagate Dockstar Seagate GoFlex Net Seagate GoFlex Home Pogoplug v1 Pogoplug Pink (v2) Do not run this installer on any other device. By typing ok, you agree to assume all liabilities and risks associated with running this installer. If you agree, type 'ok' and press ENTER to continue: ok # checking for /usr/sbin/nandwrite... # checking for /usr/sbin/nanddump... # checking for /usr/sbin/flash_erase... # checking for /usr/sbin/fw_printenv... # checking for /etc/fw_env.config... # Validating existing uBoot... Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x00080000... Connecting to jeff.doozan.com (50.116.34.13:80) Connecting to projects.doozan.com (50.116.34.13:80) valid-uboot.md5 100% |************************************************************************************************************| 1133 --:--:-- ETA ## Valid uBoot detected: [goflexnet davygravy-2012-04-19-current] ## The newest uBoot is already installed on mtd0. You are already running the latest uBoot. Your current uBoot environment should be reasonable. However, if you're having any probems booting, you can reset the environment variables to know good values. Would you like to reset the uBoot environment? [N/y] y # Installing uBoot environment Connecting to download.doozan.com (50.116.34.13:80) uboot.environment.md 100% |************************************************************************************************************| 32 --:--:-- ETA Connecting to download.doozan.com (50.116.34.13:80) uboot.environment 100% |************************************************************************************************************| 128k 00:00:00 ETA Erase Total 1 Units Performing Flash Erase of length 131072 at offset 0xc0000 done Writing data to block 6 at offset 0xc0000 # Verifying uBoot environment Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x000c0000 and ending at 0x000e0000... Connecting to download.doozan.com (50.116.34.13:80) uboot.environment.md 100% |************************************************************************************************************| 32 --:--:-- ETA # uBoot installation has completed successfully. rescue:/tmp# fw_setenv serverip 192.168.0.89 rescue:/tmp# fw_setenv ipaddr 192.168.0.94 rescue:/tmp# fw_setenv if_netconsole 'ping $serverip' rescue:/tmp# fw_setenv start_netconsole 'setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;' rescue:/tmp# fw_setenv preboot 'run if_netconsole start_netconsole'
Re: Still having trouble with a new uboot install November 20, 2012 06:30PM |
Admin Registered: 13 years ago Posts: 18,495 |
> rescue:/tmp# ./install_uboot_mtd0.sh > > > !!!!!! DANGER DANGER DANGER DANGER DANGER DANGER > !!!!!! > > If you lose power to your device while running > this script, > it could be left in an unusable state. > > This script will replace the bootloader on > /dev/mtd0. > > This installer will only work on the following > devices: > Seagate Dockstar > Seagate GoFlex Net > Seagate GoFlex Home > Pogoplug v1 > Pogoplug Pink (v2) > Do not run this installer on any other device. > > By typing ok, you agree to assume all liabilities > and risks > associated with running this installer. > > If you agree, type 'ok' and press ENTER to > continue: ok > # checking for /usr/sbin/nandwrite... > # checking for /usr/sbin/nanddump... > # checking for /usr/sbin/flash_erase... > # checking for /usr/sbin/fw_printenv... > # checking for /etc/fw_env.config... > > # Validating existing uBoot... > Block size 131072, page size 2048, OOB size 64 > Dumping data starting at 0x00000000 and ending at > 0x00080000... > Connecting to jeff.doozan.com (50.116.34.13:80) > Connecting to projects.doozan.com > (50.116.34.13:80) > valid-uboot.md5 100% > |************************************************* > ************************************************** > *********| 1133 --:--:-- ETA > ## Valid uBoot detected: [goflexnet > davygravy-2012-04-19-current] > ## The newest uBoot is already installed on mtd0. > > > You are already running the latest uBoot. > Your current uBoot environment should be > reasonable. However, if you're having > any probems booting, you can reset the environment > variables to know good values. > Would you like to reset the uBoot environment? > [N/y] y > > # Installing uBoot environment > Connecting to download.doozan.com > (50.116.34.13:80) > uboot.environment.md 100% > |************************************************* > ************************************************** > *********| 32 --:--:-- ETA > Connecting to download.doozan.com > (50.116.34.13:80) > uboot.environment 100% > |************************************************* > ************************************************** > *********| 128k 00:00:00 ETA > Erase Total 1 Units > Performing Flash Erase of length 131072 at offset > 0xc0000 done > Writing data to block 6 at offset 0xc0000 > > # Verifying uBoot environment > Block size 131072, page size 2048, OOB size 64 > Dumping data starting at 0x000c0000 and ending at > 0x000e0000... > Connecting to download.doozan.com > (50.116.34.13:80) > uboot.environment.md 100% > |************************************************* > ************************************************** > *********| 32 --:--:-- ETA > > # uBoot installation has completed successfully. > > rescue:/tmp# fw_setenv serverip 192.168.0.89 > rescue:/tmp# fw_setenv ipaddr 192.168.0.94 > rescue:/tmp# fw_setenv if_netconsole 'ping > $serverip' > rescue:/tmp# fw_setenv start_netconsole 'setenv > ncip $serverip; setenv bootdelay 10; setenv stdin > nc; setenv stdout nc; setenv stderr nc; version;' > rescue:/tmp# fw_setenv preboot 'run if_netconsole > start_netconsole' > >