uBoot install canceled with Pogo E02(Black) January 29, 2013 09:45AM |
Registered: 11 years ago Posts: 5 |
Processor : ARM926EJ-S rev 1 (v5l) BogoMIPS : 1192.75 Features : swp half thumb fastmult edsp CPU implementer : 0x56 CPU architecture: 5TE CPU variant : 0x2 CPU part : 0x131 CPU revision : 1 Cache type : write-back Cache clean : cp15 c7 ops Cache lockdown : format C Cache format : Harvard I size : 16384 I assoc : 4 I line length : 32 I sets : 128 D size : 16384 D assoc : 4 D line length : 32 D sets : 128 Hardware : Feroceon-KW Revision : 0000 Serial : 0000000000000000
Linux Pogoplug 2.6.22.18 #81 Tue Oct 19 16:05:00 PDT 2010 armv5tejl unknown
Linux version 2.6.22.18 (bdietrich@buildman) (gcc version 4.2.1) #81 Tue Oct 19 16:05:00 PDT 2010
MemTotal: 256008 kB MemFree: 154968 kB Buffers: 12 kB Cached: 84940 kB SwapCached: 0 kB Active: 18712 kB Inactive: 67140 kB SwapTotal: 0 kB SwapFree: 0 kB Dirty: 0 kB Writeback: 0 kB AnonPages: 928 kB Mapped: 1588 kB Slab: 13472 kB SReclaimable: 1368 kB SUnreclaim: 12104 kB PageTables: 96 kB NFS_Unstable: 0 kB Bounce: 0 kB CommitLimit: 128004 kB Committed_AS: 83048 kB VmallocTotal: 385024 kB VmallocUsed: 324 kB VmallocChunk: 384696 kB
baudrate=115200 loads_echo=0 rootpath=/mnt/ARM_FS/ netmask=255.255.0.0 run_diag=yes console=console=ttyS0,115200 CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_root=root=/dev/mtdblock2 ro ethmtu=1500 usb0Mode=host nandEcc=1bit ethact=egiga0 stdin=serial stdout=serial stderr=serial mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no bootargs=console=ttyS0,115200 root=/dev/mtdblock2 ro serverip=169.254.254.252 ipaddr=169.254.254.253 ethaddr=00:25:31:02:D6:74 cesvcid=LE9FW64CV8GHU3Z46W8Q2S3Z7N ceboardver=PPV2 bootcmd=nand read.e 0x800000 0x100000 0x200000; setenv bootargs $(console) $(bootargs_root); bootm 0x800000
ethact=egiga0 bootdelay=3 baudrate=115200 arcNumber=2097 mainlineLinux=yes console=ttyS0,115200 led_init=green blinking led_exit=green off led_error=orange blinking mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) mtdids=nand0=orion_nand partition=nand0,2 stdin=serial stdout=serial stderr=serial rescue_installed=0 rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi ubifs_mtd=3 ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done usb_scan_list=1 2 3 4 usb_scan_1=usb=0:1 dev=sda1 usb_scan_2=usb=1:1 dev=sdb1 usb_scan_3=usb=2:1 dev=sdc1 usb_scan_4=usb=3:1 dev=sdd1 usb_init=run usb_scan usb_device=0:1 usb_root=/dev/sda1 usb_rootfstype=ext2 usb_rootdelay=10 usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset
[ 0.000000] Linux version 2.6.22.18 (bdietrich@buildman) (gcc version 4.2.1) #81 Tue Oct 19 16:05:00 PDT 2010 [ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177 [ 0.000000] Machine: Feroceon-KW [ 0.000000] Using UBoot passing parameters structure [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 65536 [ 0.000000] DMA zone: 512 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 65024 pages, LIFO batch:15 [ 0.000000] Normal zone: 0 pages used for memmap [ 0.000000] CPU0: D VIVT write-back cache [ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] Built 1 zonelists. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro [ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes) [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.010000] Memory: 256MB 0MB 0MB 0MB = 256MB total [ 0.010000] Memory: 255872KB available (3592K code, 253K data, 124K init) [ 0.010000] Calibrating delay loop... 1192.75 BogoMIPS (lpj=5963776) [ 0.250000] Mount-cache hash table entries: 512 [ 0.250000] CPU: Testing write buffer coherency: ok [ 0.250000] NET: Registered protocol family 16 [ 0.250000] [ 0.250000] CPU Interface [ 0.250000] ------------- [ 0.250000] SDRAM_CS0 ....base 00000000, size 256MB [ 0.250000] SDRAM_CS1 ....disable [ 0.250000] SDRAM_CS2 ....disable [ 0.250000] SDRAM_CS3 ....disable [ 0.250000] PEX0_MEM ....base e8000000, size 128MB [ 0.250000] PEX0_IO ....base f2000000, size 1MB [ 0.250000] INTER_REGS ....base f1000000, size 1MB [ 0.250000] NFLASH_CS ....base fa000000, size 2MB [ 0.250000] SPI_CS ....base f4000000, size 16MB [ 0.250000] BOOT_ROM_CS ....no such [ 0.250000] DEV_BOOTCS ....no such [ 0.250000] CRYPT_ENG ....base f0000000, size 2MB [ 0.250000] [ 0.250000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21_with_rx_desc_tuned)-- SHEEVA PLUG Soc: 88F6281 A0 LE [ 0.250000] [ 0.250000] Detected Tclk 200000000 and SysClk 400000000 [ 0.250000] MV Buttons Device Load [ 0.250000] Marvell USB EHCI Host controller #0: c0652600 [ 0.750000] PEX0 interface detected no Link. [ 0.750000] PCI: bus0: Fast back to back transfers enabled [ 0.750000] SCSI subsystem initialized [ 0.750000] usbcore: registered new interface driver usbfs [ 0.750000] usbcore: registered new interface driver hub [ 0.750000] usbcore: registered new device driver usb [ 0.750000] NET: Registered protocol family 2 [ 0.760000] Time: kw_clocksource clocksource has been installed. [ 0.850000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.850000] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.850000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes) [ 0.850000] TCP: Hash tables configured (established 8192 bind 8192) [ 0.850000] TCP reno registered [ 0.880000] RTC has been updated!!! [ 0.880000] RTC registered [ 0.880000] Use the XOR engines (acceleration) for enhancing the following functions: [ 0.880000] o RAID 5 Xor calculation [ 0.880000] o kernel memcpy [ 0.880000] o kenrel memzero [ 0.880000] Number of XOR engines to use: 4 [ 0.880000] cesadev_init(c00117b0) [ 0.880000] mvCesaInit: sessions=640, queue=64, pSram=f0000000 [ 0.880000] MV Buttons Driver Load [ 0.880000] squashfs: version 3.3 (2007/10/31) Phillip Lougher [ 0.880000] squashfs: LZMA suppport for slax.org by jro [ 0.880000] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.880000] io scheduler noop registered [ 0.880000] io scheduler anticipatory registered (default) [ 0.900000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [ 0.900000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A [ 0.910000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize [ 0.920000] Loading Marvell Ethernet Driver: [ 0.920000] o Cached descriptors in DRAM [ 0.920000] o DRAM SW cache-coherency [ 0.930000] o Single RX Queue support - ETH_DEF_RXQ=0 [ 0.930000] o Single TX Queue support - ETH_DEF_TXQ=0 [ 0.940000] o TCP segmentation offload enabled [ 0.940000] o Receive checksum offload enabled [ 0.950000] o Transmit checksum offload enabled [ 0.950000] o Network Fast Processing (Routing) supported [ 0.960000] o Driver ERROR statistics enabled [ 0.960000] o Driver INFO statistics enabled [ 0.970000] o Proc tool API enabled [ 0.970000] o Rx descripors: q0=128 [ 0.970000] o Tx descripors: q0=532 [ 0.980000] o Loading network interface(s): [ 0.990000] o eth0, ifindex = 1, GbE port = 0 [ 0.990000] o eth1, ifindex = 2, GbE port = 1 [ 1.000000] [ 1.000000] mvFpRuleDb (cfdf6000): 2048 entries, 8192 bytes [ 1.000000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI [ 1.010000] Copyright (c) 1999-2006 Intel Corporation. [ 1.020000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI [ 1.020000] e100: Copyright(c) 1999-2006 Intel Corporation [ 1.030000] [ 1.030000] Warning Sata is Powered Off [ 1.030000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ [ 1.040000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit) [ 1.050000] Scanning device for bad blocks [ 1.050000] Bad eraseblock 3 at 0x00060000 [ 1.110000] Using static partition definition [ 1.110000] Creating 4 MTD partitions on "nand_mtd": [ 1.120000] 0x00000000-0x00100000 : "u-boot" [ 1.120000] 0x00100000-0x00500000 : "uImage" [ 1.130000] 0x00500000-0x02500000 : "root" [ 1.130000] 0x02500000-0x08000000 : "data" [ 1.140000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI [ 1.140000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 [ 1.180000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 [ 1.200000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 1.200000] usb usb1: configuration #1 chosen from 1 choice [ 1.210000] hub 1-0:1.0: USB hub found [ 1.210000] hub 1-0:1.0: 1 port detected [ 1.330000] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.330000] USB Universal Host Controller Interface driver v3.0 [ 1.610000] usb 1-1: new high speed USB device using ehci_marvell and address 2 [ 1.760000] usb 1-1: configuration #1 chosen from 1 choice [ 1.760000] hub 1-1:1.0: USB hub found [ 1.770000] hub 1-1:1.0: 4 ports detected [ 1.880000] usbcore: registered new interface driver usblp [ 1.880000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver [ 1.890000] Initializing USB Mass Storage driver... [ 1.890000] usbcore: registered new interface driver usb-storage [ 1.900000] USB Mass Storage support registered. [ 1.910000] mice: PS/2 mouse device common for all mice [ 1.910000] i2c /dev entries driver [ 1.910000] Linux telephony interface: v1.00 [ 1.920000] md: linear personality registered for level -1 [ 1.920000] md: raid0 personality registered for level 0 [ 1.930000] md: raid1 personality registered for level 1 [ 2.100000] raid6: int32x1 97 MB/s [ 2.270000] raid6: int32x2 114 MB/s [ 2.440000] raid6: int32x4 122 MB/s [ 2.610000] raid6: int32x8 110 MB/s [ 2.610000] raid6: using algorithm int32x4 (122 MB/s) [ 2.610000] md: raid6 personality registered for level 6 [ 2.620000] md: raid5 personality registered for level 5 [ 2.620000] md: raid4 personality registered for level 4 [ 2.630000] raid5: measuring checksumming speed [ 2.680000] arm4regs : 1084.000 MB/sec [ 2.730000] 8regs : 754.800 MB/sec [ 2.780000] 32regs : 899.600 MB/sec [ 2.780000] raid5: using function: arm4regs (1084.000 MB/sec) [ 2.790000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com [ 2.790000] dm_crypt using the OCF package. [ 2.800000] sdhci: Secure Digital Host Controller Interface driver [ 2.800000] sdhci: Copyright(c) Pierre Ossman [ 2.810000] usbcore: registered new interface driver usbhid [ 2.810000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 2.820000] TCP cubic registered [ 2.820000] NET: Registered protocol family 1 [ 2.830000] NET: Registered protocol family 17 [ 2.830000] md: Autodetecting RAID arrays. [ 2.840000] md: autorun ... [ 2.840000] md: ... autorun DONE. [ 4.600000] Empty flash at 0x009ac208 ends at 0x009ac800 [ 8.800000] VFS: Mounted root (jffs2 filesystem) readonly. [ 8.800000] Freeing init memory: 124K [ 10.940000] eth0: link down [ 10.950000] eth0: started [ 12.530000] eth0: link up, full duplex, speed 100 Mbps
Pogoplug:/$ cd /tmp Pogoplug:/tmp$ wget http://jeff.doozan.com/debian/uboot/install_uboot_mtd0.sh Connecting to jeff.doozan.com (50.116.34.13:80) install_uboot_mtd0.s 100% |*******************************| 18406 00:00:00 ETA Pogoplug:/tmp$ chmod +x install_uboot_mtd0.sh Pogoplug:/tmp$ ./install_uboot_mtd0.sh !!!!!! DANGER DANGER DANGER DANGER DANGER DANGER !!!!!! If you lose power to your device while running this script, it could be left in an unusable state. This script will replace the bootloader on /dev/mtd0. This installer will only work on the following devices: Seagate Dockstar Seagate GoFlex Net Seagate GoFlex Home Pogoplug v1 Pogoplug Pink (v2) Do not run this installer on any other device. By typing ok, you agree to assume all liabilities and risks associated with running this installer. If you agree, type 'ok' and press ENTER to continue: ok # checking for /usr/sbin/nandwrite... # checking for /usr/sbin/nanddump... # checking for /usr/sbin/flash_erase... # checking for /usr/sbin/fw_printenv... # checking for /etc/fw_env.config... # Validating existing uBoot... Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x00080000... Connecting to jeff.doozan.com (50.116.34.13:80) valid-uboot.md5 100% |*******************************| 1133 --:--:-- ETA ## Unknown uBoot detected on mtd0: ec3fadd50ae24760b035b0afe9ac6018 ## ## The installer could not detect the version of your current uBoot ## This may happen if you have installed a different uBoot on ## /dev/mtd0 or if you have bad blocks on /dev/mtd0 ## ## If you have bad blocks on mtd0, you should not try to install uBoot. ## ## Installation cancelled.
Pogoplug:/tmp$ ./install_uboot_mtd0.sh --noprompt --no-uboot-check parameter # checking for /usr/sbin/nandwrite... # checking for /usr/sbin/nanddump... # checking for /usr/sbin/flash_erase... # checking for /usr/sbin/fw_printenv... # checking for /etc/fw_env.config... # Validating existing uBoot... Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x00080000... Connecting to jeff.doozan.com (50.116.34.13:80) valid-uboot.md5 100% |*******************************| 1133 --:--:-- ETA ## Unknown uBoot detected on mtd0: ec3fadd50ae24760b035b0afe9ac6018 ## ## --no-uboot-check flag detected, continuing installation ############################################ Your device could not be auto-detected. You must be using a device listed below to run this installer. What device are you using? Type the number of your device and press ENTER. 1 - Seagate Dockstar 2 - Seagate GoFlex Net 3 - Seagate GoFlex Home 4 - Pogoplug v1 5 - Pogoplug v2 - Pink 6 - Other 5 Selected Pogoplug v2 - Pink # Installing uBoot ## Installing pinkpogo davygravy-2012-02-20 Connecting to download.doozan.com (50.116.34.13:80) uboot.mtd0.kwb.md5 100% |*******************************| 32 --:--:-- ETA Connecting to download.doozan.com (50.116.34.13:80) uboot.mtd0.kwb 100% |*******************************| 512k 00:00:00 ETA Erase Total 4 Units Performing Flash Erase of length 131072 at offset 0x60000 MTD Erase failure: Input/output error Writing data to block 0 at offset 0x0 Writing data to block 1 at offset 0x20000 Writing data to block 2 at offset 0x40000 Writing data to block 3 at offset 0x60000 Bad block at 60000, 1 block(s) from 60000 will be skipped Writing data to block 4 at offset 0x80000 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x00080000... ## Verifying new uBoot... Connecting to download.doozan.com (50.116.34.13:80) uboot.mtd0.kwb.md5 100% |*******************************| 32 --:--:-- ETA ## ## ## VERIFICATION FAILED! ## ## uBoot was not properly installed to mtd0. ## ## ## YOUR DEVICE MAY BE IN AN UNUSABLE STATE. ## DO NOT REBOOT OR POWER OFF YOUR DEVICE ## ## ## Make a backup of /tmp/uboot-mtd0-dump someplace safe and ## then re-run this installer.
Re: uBoot install canceled with Pogo E02(Black) January 29, 2013 01:00PM |
Admin Registered: 13 years ago Posts: 18,548 |
Re: uBoot install canceled with Pogo E02(Black) January 30, 2013 06:08AM |
Registered: 11 years ago Posts: 3 |
Re: uBoot install canceled with Pogo E02(Black) January 30, 2013 09:32AM |
Registered: 11 years ago Posts: 5 |
Pogoplug:/tmp$ /usr/sbin/flash_erase /dev/mtd0 0 5 Erase Total 5 Units Performing Flash Erase of length 131072 at offset 0x60000 MTD Erase failure: Input/output error Pogoplug:/tmp$ /usr/sbin/nandwrite /dev/mtd0 uboot.mtd0.kwb Writing data to block 0 at offset 0x0 Writing data to block 1 at offset 0x20000 Writing data to block 2 at offset 0x40000 Writing data to block 3 at offset 0x60000 Bad block at 60000, 1 block(s) from 60000 will be skipped Writing data to block 4 at offset 0x80000
Pogoplug:/tmp$ /usr/sbin/nanddump -bnof /tmp/uBoot.dump -l 0x80000 /dev/mtd0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x00080000...
Pogoplug:/tmp$ wget -O /tmp/uboot.environment http://jeff.doozan.com/debian/uboot/files/environment/uboot.environment Connecting to jeff.doozan.com (50.116.34.13:80) uboot.environment 100% |***********************************************************| 128k 00:00:00 ETA
Pogoplug:/tmp$ /usr/sbin/flash_erase /dev/mtd0 0xc0000 1 Erase Total 1 Units Performing Flash Erase of length 131072 at offset 0xc0000 done Pogoplug:/tmp$ /usr/sbin/nandwrite -s 786432 /dev/mtd0 /tmp/uboot.environment Writing data to block 6 at offset 0xc0000
Pogoplug:/tmp$ /usr/sbin/fw_setenv ethaddr=00:25:31:02:D6:74 Pogoplug:/tmp$ /usr/sbin/fw_setenv serverip 192.168.25.2 Pogoplug:/tmp$ /usr/sbin/fw_setenv ipaddr 192.168.25.7 Pogoplug:/tmp$ /usr/sbin/fw_setenv serverip 192.168.25.2 Pogoplug:/tmp$/usr/sbin/fw_setenv start_netconsole 'setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;' Pogoplug:/tmp$ /usr/sbin/fw_setenv preboot 'dhcp; run if_netconsole start_netconsole' Pogoplug:/tmp$ /usr/sbin/fw_setenv if_netconsole 'ping $serverip'
Pogoplug:~$ cd /tmp Pogoplug:/tmp$ chmod +x install_uboot_mtd0.sh Pogoplug:/tmp$ ./install_uboot_mtd0.sh --no-uboot-check parameter !!!!!! DANGER DANGER DANGER DANGER DANGER DANGER !!!!!! If you lose power to your device while running this script, it could be left in an unusable state. This script will replace the bootloader on /dev/mtd0. This installer will only work on the following devices: Seagate Dockstar Seagate GoFlex Net Seagate GoFlex Home Pogoplug v1 Pogoplug Pink (v2) Do not run this installer on any other device. By typing ok, you agree to assume all liabilities and risks associated with running this installer. If you agree, type 'ok' and press ENTER to continue: ok # checking for /usr/sbin/nandwrite... # checking for /usr/sbin/nanddump... # checking for /usr/sbin/flash_erase... # checking for /usr/sbin/fw_printenv... # checking for /etc/fw_env.config... # Validating existing uBoot... Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x00080000... Connecting to jeff.doozan.com (50.116.34.13:80) valid-uboot.md5 100% |*******************************| 1133 --:--:-- ETA ## Unknown uBoot detected on mtd0: ec3fadd50ae24760b035b0afe9ac6018 ## ## --no-uboot-check flag detected, continuing installation ############################################ Your device could not be auto-detected. You must be using a device listed below to run this installer. What device are you using? Type the number of your device and press ENTER. 1 - Seagate Dockstar 2 - Seagate GoFlex Net 3 - Seagate GoFlex Home 4 - Pogoplug v1 5 - Pogoplug v2 - Pink 6 - Other 5 Selected Pogoplug v2 - Pink # Installing uBoot ## Installing pinkpogo davygravy-2012-02-20 Connecting to download.doozan.com (50.116.34.13:80) uboot.mtd0.kwb.md5 100% |*******************************| 32 --:--:-- ETA Connecting to download.doozan.com (50.116.34.13:80) uboot.mtd0.kwb 100% |*******************************| 512k 00:00:00 ETA Erase Total 4 Units Performing Flash Erase of length 131072 at offset 0x60000 MTD Erase failure: Input/output error Writing data to block 0 at offset 0x0 Writing data to block 1 at offset 0x20000 Writing data to block 2 at offset 0x40000 Writing data to block 3 at offset 0x60000 Bad block at 60000, 1 block(s) from 60000 will be skipped Writing data to block 4 at offset 0x80000 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x00080000... ## Verifying new uBoot... Connecting to download.doozan.com (50.116.34.13:80) uboot.mtd0.kwb.md5 100% |*******************************| 32 --:--:-- ETA ## ## ## VERIFICATION FAILED! ## ## uBoot was not properly installed to mtd0. ## ## ## YOUR DEVICE MAY BE IN AN UNUSABLE STATE. ## DO NOT REBOOT OR POWER OFF YOUR DEVICE ## ## ## Make a backup of /tmp/uboot-mtd0-dump someplace safe and ## then re-run this installer.
Re: uBoot install canceled with Pogo E02(Black) January 30, 2013 12:23PM |
Admin Registered: 13 years ago Posts: 18,548 |
Re: uBoot install canceled with Pogo E02(Black) January 31, 2013 09:28AM |
Registered: 11 years ago Posts: 5 |
Pogoplug:/tmp$ /usr/sbin/nanddump -nof /tmp/uBoot1.dump -l 0x60000 /dev/mtd0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x00060000... <nddump -nof /tmp/uBoot2.dump -l 0x20000 -s 0x80000 /dev/mtd0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00080000 and ending at 0x000a0000... Pogoplug:/tmp$ cat uBoot1.dump uBoot2.dump > uBoot.dump Pogoplug:/tmp$ Pogoplug:/tmp$ ls -l uBoot*.dump -rw-r--r-- 1 root root 524288 Jan 1 22:25 uBoot.dump -rw-r--r-- 1 root root 393216 Jan 1 22:25 uBoot1.dump -rw-r--r-- 1 root root 131072 Jan 1 22:25 uBoot2.dump Pogoplug:/tmp$ ls -l uboot.mtd0.kwb -rw-r--r-- 1 root root 524288 Jan 1 22:22 uboot.mtd0.kwb Pogoplug:/tmp$ ls -l uboot.mtd0.kwb -rw-r--r-- 1 root root 524288 Jan 1 22:22 uboot.mtd0.kwb Pogoplug:/tmp$ diff -s uboot.mtd0.kwb uBoot.dump Files uboot.mtd0.kwb and uBoot.dump are identical
Re: uBoot install canceled with Pogo E02(Black) January 31, 2013 02:25PM |
Admin Registered: 13 years ago Posts: 18,548 |
Pogoplug:/tmp$ /usr/sbin/fw_setenv ethaddr=00:25:31:02:D6:74
Re: uBoot install canceled with Pogo E02(Black) February 01, 2013 10:10PM |
Registered: 11 years ago Posts: 5 |
Pogoplug:/tmp$ /usr/sbin/fw_printenv ethact=egiga0 bootdelay=3 baudrate=115200 arcNumber=2097 mainlineLinux=yes console=ttyS0,115200 led_init=green blinking led_exit=green off led_error=orange blinking mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) mtdids=nand0=orion_nand partition=nand0,2 stdin=serial stdout=serial stderr=serial rescue_installed=0 rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi ubifs_mtd=3 ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done usb_scan_list=1 2 3 4 usb_scan_1=usb=0:1 dev=sda1 usb_scan_2=usb=1:1 dev=sdb1 usb_scan_3=usb=2:1 dev=sdc1 usb_scan_4=usb=3:1 dev=sdd1 usb_init=run usb_scan usb_device=0:1 usb_root=/dev/sda1 usb_rootfstype=ext2 usb_rootdelay=10 usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset ipaddr=192.168.25.7 serverip=192.168.25.2 start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; preboot=dhcp; run if_netconsole start_netconsole if_netconsole=ping $serverip
Re: uBoot install canceled with Pogo E02(Black) February 01, 2013 10:32PM |
Admin Registered: 13 years ago Posts: 18,548 |
Re: uBoot install canceled with Pogo E02(Black) February 02, 2013 09:30AM |
Registered: 11 years ago Posts: 5 |
c:/nc>nc -l -u -p 6666 U-Boot 2011.12 <Feb 20 2012 - 21:21:59> Pogoplug E02 arm-none-linux-guneabi-gcc <Sourcery G++ Lite 2009q3-67> 4.4.1 GNI Id <Sourcery G++ Lite 2009q3-67> 2.19.51.20090709 Hit any key to stop autoboot: 0 <Re>start USB... USB: Register 10011 NbrPorts 1 UBS EHCI 1.00 scanning bus for devices... 3 USB Device<s> found scanning bus for storage devices...1 Storage Device<s> found Loading file "/rescueme" from usb device 0:1 <usbda1> ** File not found /rescueme reading /rescueme.txt ** Unable to read "/rescueme.txt" from usb 0:1 ** Creating 1 MTD partitions on "nand0": 0x000002500000-0x000008000000 : "mtd=3" UBI : attaching mtd1 to ubi0 UBI : physical eraseblock size: 131072 bytes <128 KiB> UBI : logical eraseblock size: 129024 bytes UBI : smallest flash I/O unit: 2048 UBI : sub-page size: 512 UBI : VID header offset: 512 <aligned 512> UBI : data offset: 2048 UBI : attached mtd1 to ubi0 UBI : MTD device name: "mtd=3" UBI : MTD device size: 91 MiB UBI : number of good PEBs: 728 UBI : number of bad PEBs: 0 UBI : max. allowed volumes: 128 UBI : wear-leveling threshold: 4096 UBI : number of internal volumes: 1 UBI : number of user volumes: 0 UBI : available PEBs 717 UBI : total number of reserved PEBs : 11 UBI : number of PEBs reserved for bad PEB handling: 7 UBI : max/mean erase counter: 1/1 UBIPS error <pid 0>: ubifs_get_sb: cannot open "ubi:rootfs", error -19 Error reading superblock on volume 'ubi:rootfs'! Loading file "/boot/uImage" from usb device 0:1 <usbda1> 1 bytes read Found bootable drive on usb 0:1 Loading file "/boot/uImage" from usb device 0:1 <usbda1> 2177376 bytes read Loading file "/boot/uInitrd" from usb device 0:1 <usbda1> 3795183 bytes read ## Booting kernel from Legacy Image at 0080000 ... Image Name: Linux-3.0.3-rt12-PogoPlugMPD_xt Image Type: ARM Linux Kernel Image <uncompressed> Data Size: 2177312 Bytes = 2.1 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loadig init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs Image Type: ARM Linux RAMDisk Image <gzip compressed> Data Size: 3795119 Bytes = 3.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting Kernel ...
Re: uBoot install canceled with Pogo E02(Black) February 02, 2013 12:02PM |
Admin Registered: 13 years ago Posts: 18,548 |