Pogoplug E04 not booting from SD Card or USB

I followed this link to be able to boot my old Pogoplug EO4 from either an SD card or USB:
Qnology PogoPlug Booting from SD

All appears to be OK except it always keeps booting into the Popoplug. When I ssh into the device it is always the Pogoplug kernel.

I tried different SanDisk SD cards and USB sticks to no avail, it always only boots to the Pogoplug.

I used screen and booted a second time to capture the log file and the weird thing is alarm was loaded. I could login to the alarm kernel over serial (alarm, alarm), and at the same time I could ssh into the Pogoplug device as root and my root password.

I read through the posts here since the above link seems to be dead for sometime now and I saw a post from bodhi about the rootfs not being mounted properly.

I then logged into Linux mint as root and recreated my ArchLinux rootfs card. I plugged the SD card back into my Pogoplug and rebooted. It behaves differently and still wont boot into ArchLinux on the SD card.

If you look at the console log, it appears to all be working fine, but its not loading. Looking at the second console log after using the SD card from Linux mint, it appears as though it can't find the image, but it still loads. It also tries to load ArchLinux but hangs partway through.

At this point I'm wondering if the ArchLinux version is simply too new for the Pogoplug hardware and should I be trying to load an older version?
Here is my first serial console output:

U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45)
Pogoplug V4

SoC:   Kirkwood 88F6192_A1
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  128 MiB
MMC:   kwsdio: 0
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Hit any key to stop autoboot:  0 

MMC rescan: current device # 0 initialized OK
4621184 bytes read in 1036 ms (4.3 MiB/s)
** File not found /boot/uInitrd **
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-4.4.227-1-ARCH
   Created:      2020-06-13   3:57:53 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4621120 Bytes = 4.4 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
Using machid 0xf78 from environment

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.4.227-1-ARCH (builduser@leming) (gcc version 9.3.0 (GCC) ) #1 PREEMPT Sat Jun 13 04:13:48 UTC 2020
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: Pogoplug V4
[    0.000000] Memory policy: Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p1 rootdelay=10 rootfstype=ext3 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 119668K/131072K available (6614K kernel code, 548K rwdata, 1892K rodata, 300K init, 720K bss, 11404K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0856b2c   (8507 kB)
[    0.000000]       .init : 0xc0857000 - 0xc08a2000   ( 300 kB)
[    0.000000]       .data : 0xc08a2000 - 0xc092b35c   ( 549 kB)
[    0.000000]        .bss : 0xc092b35c - 0xc09df508   ( 721 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	Build-time adjustment of leaf fanout to 32.
[    0.000000] NR_IRQS:114
[    0.000019] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[   10.582633] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[   10.582917] Console: colour dummy device 80x30
[   10.582963] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216)
[   10.672738] pid_max: default: 32768 minimum: 301
[   10.672876] Security Framework initialized
[   10.672994] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[   10.673022] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[   10.674135] Initializing cgroup subsys io
[   10.674187] Initializing cgroup subsys memory
[   10.674270] Initializing cgroup subsys devices
[   10.674312] Initializing cgroup subsys freezer
[   10.674345] Initializing cgroup subsys net_cls
[   10.674378] Initializing cgroup subsys perf_event
[   10.674413] Initializing cgroup subsys net_prio
[   10.674533] CPU: Testing write buffer coherency: ok
[   10.675242] Setting up static identity map for 0x81e0 - 0x8238
[   10.678217] devtmpfs: initialized
[   10.681982] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[   10.682045] futex hash table entries: 256 (order: -1, 3072 bytes)
[   10.682928] pinctrl core: initialized pinctrl subsystem
[   10.684059] NET: Registered protocol family 16
[   10.684887] DMA: preallocated 256 KiB pool for atomic coherent allocations
[   10.712770] cpuidle: using governor ladder
[   10.742767] cpuidle: using governor menu
[   10.743055] Kirkwood: MV88F6281-A1, TCLK=166666667.
[   10.743094] Feroceon L2: Enabling L2
[   10.743147] Feroceon L2: Cache support initialised.
[   10.746528] Kirkwood PCIe port 0: link up
[   10.746544] PCI: bus0 uses PCIe port 0
[   10.746885] PCI host bridge to bus 0000:00
[   10.746911] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[   10.746929] pci_bus 0000:00: root bus resource [io  0x1000-0xffff]
[   10.746945] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[   10.748093] PCI: bus0: Fast back to back transfers disabled
[   10.748165] pci 0000:00:01.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff 64bit]
[   10.748199] pci 0000:00:01.0: BAR 2: assigned [mem 0xe0010000-0xe0010fff 64bit]
[   10.748229] pci 0000:00:01.0: BAR 4: assigned [mem 0xe0011000-0xe0011fff 64bit]
[   10.784933] vgaarb: loaded
[   10.785421] SCSI subsystem initialized
[   10.786167] usbcore: registered new interface driver usbfs
[   10.786287] usbcore: registered new interface driver hub
[   10.786371] usbcore: registered new device driver usb
[   10.786597] pps_core: LinuxPPS API ver. 1 registered
[   10.786611] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[   10.786657] PTP clock support registered
[   10.788267] clocksource: Switched to clocksource orion_clocksource
[   10.847156] FS-Cache: Loaded
[   10.865953] NET: Registered protocol family 2
[   10.867086] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[   10.867127] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[   10.867156] TCP: Hash tables configured (established 1024 bind 1024)
[   10.867266] UDP hash table entries: 256 (order: 0, 4096 bytes)
[   10.867298] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[   10.867592] NET: Registered protocol family 1
[   10.868064] RPC: Registered named UNIX socket transport module.
[   10.868080] RPC: Registered udp transport module.
[   10.868090] RPC: Registered tcp transport module.
[   10.868100] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   10.868174] pci 0000:00:01.0: enabling device (0140 -> 0142)
[   10.890550] VFS: Disk quotas dquot_6.6.0
[   10.890955] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   10.893990] FS-Cache: Netfs 'nfs' registered for caching
[   10.895679] NFS: Registering the id_resolver key type
[   10.895751] Key type id_resolver registered
[   10.895762] Key type id_legacy registered
[   10.895894] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[   10.897793] fuse init (API version 7.23)
[   10.901182] aufs 4.4-20170911
[   10.908936] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[   10.908966] io scheduler noop registered
[   10.908985] io scheduler deadline registered
[   10.909386] io scheduler cfq registered
[   10.909764] io scheduler bfq registered (default)
[   10.909776] BFQ I/O-scheduler: v7r11
[   10.910099] mv_xor mv_xor.0: Marvell shared XOR driver
[   10.950165] mv_xor mv_xor.0: Marvell XOR (Registers Mode): ( xor cpy )
[   10.950506] mv_xor mv_xor.1: Marvell shared XOR driver
[   10.990075] mv_xor mv_xor.1: Marvell XOR (Registers Mode): ( xor cpy )
[   10.998247] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[   10.999812] console [ttyS0] disabled
[   11.019896] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 10416666) is a 16550A
[   11.637828] console [ttyS0] enabled
[   11.664684] brd: module loaded
[   11.679205] loop: module loaded
[   11.682859] sata_mv sata_mv.0: cannot get optional clkdev
[   11.688411] sata_mv sata_mv.0: slots 32 ports 1
[   11.695403] scsi host0: sata_mv
[   11.699141] ata1: SATA max UDMA/133 irq 21
[   11.704242] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[   11.710769] nand: Hynix H27U1G8F2BTR-BC
[   11.714596] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[   11.722181] Scanning device for bad blocks
[   11.810266] 5 cmdlinepart partitions found on MTD device orion_nand
[   11.816510] Creating 5 MTD partitions on "orion_nand":
[   11.821656] 0x000000000000-0x000000200000 : "u-boot"
[   11.827331] 0x000000200000-0x000000500000 : "uImage"
[   11.832970] 0x000000500000-0x000000800000 : "uImage2"
[   11.838698] 0x000000800000-0x000001000000 : "failsafe"
[   11.844482] 0x000001000000-0x000008000000 : "root"
[   11.859885] libphy: orion_mdio_bus: probed
[   11.864120] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[   12.058311] ata1: SATA link down (SStatus 0 SControl F300)
[   12.952765] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:05:f5:25
[   12.961703] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   12.968214] ehci-pci: EHCI PCI platform driver
[   12.972795] ehci-orion: EHCI orion driver
[   12.976900] orion-ehci orion-ehci.0: EHCI Host Controller
[   12.982346] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[   12.990119] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[   13.008312] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[   13.015622] hub 1-0:1.0: USB hub found
[   13.019477] hub 1-0:1.0: 1 port detected
[   13.024337] xhci_hcd 0000:00:01.0: xHCI Host Controller
[   13.029649] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 2
[   13.038593] xhci_hcd 0000:00:01.0: hcc params 0x200073a1 hci version 0x100 quirks 0x00080010
[   13.048394] hub 2-0:1.0: USB hub found
[   13.052181] hub 2-0:1.0: 2 ports detected
[   13.057053] xhci_hcd 0000:00:01.0: xHCI Host Controller
[   13.062345] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 3
[   13.069863] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[   13.079195] hub 3-0:1.0: USB hub found
[   13.082980] hub 3-0:1.0: 2 ports detected
[   13.088329] usbcore: registered new interface driver uas
[   13.093884] usbcore: registered new interface driver usb-storage
[   13.100039] usbcore: registered new interface driver ums-alauda
[   13.106019] usbcore: registered new interface driver ums-cypress
[   13.112135] usbcore: registered new interface driver ums-datafab
[   13.118192] usbcore: registered new interface driver ums_eneub6250
[   13.125101] usbcore: registered new interface driver ums-freecom
[   13.131196] usbcore: registered new interface driver ums-isd200
[   13.137165] usbcore: registered new interface driver ums-jumpshot
[   13.143335] usbcore: registered new interface driver ums-karma
[   13.149414] usbcore: registered new interface driver ums-onetouch
[   13.155597] usbcore: registered new interface driver ums-realtek
[   13.161687] usbcore: registered new interface driver ums-sddr09
[   13.167665] usbcore: registered new interface driver ums-sddr55
[   13.173666] usbcore: registered new interface driver ums-usbat
[   13.180362] mousedev: PS/2 mouse device common for all mice
[   14.188307] rtc-mv rtc-mv: internal RTC not ticking
[   14.193350] i2c /dev entries driver
[   14.197671] sdhci: Secure Digital Host Controller Interface driver
[   14.203861] sdhci: Copyright(c) Pierre Ossman
[   14.248616] sdhci-pltfm: SDHCI platform and OF driver helper
[   14.258136] ledtrig-cpu: registered to indicate activity on CPUs
[   14.264401] usbcore: registered new interface driver r8712u
[   14.270404] gre: GRE over IPv4 demultiplexor driver
[   14.275367] NET: Registered protocol family 17
[   14.280068] Key type dns_resolver registered
[   14.289046] registered taskstats version 1
[   14.295842] Key type encrypted registered
[   14.300862] console [netcon0] enabled
[   14.304509] netconsole: network logging started
[   14.309870] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[   14.317034] hctosys: unable to open rtc device (rtc0)
[   14.324132] Waiting 10 sec before mounting root device...
[   14.333401] mmc0: host does not support reading read-only switch, assuming write-enable
[   14.346119] mmc0: new high speed SDHC card at address 1234
[   14.352474] mmcblk0: mmc0:1234 SA04G 3.69 GiB 
[   14.361179]  mmcblk0: p1
[   24.341409] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem
[   28.207784] EXT4-fs (mmcblk0p1): recovery complete
[   28.224598] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
[   28.232747] VFS: Mounted root (ext3 filesystem) on device 179:1.
[   28.241354] devtmpfs: mounted
[   28.245612] Freeing unused kernel memory: 300K
[   29.323474] systemd[1]: System time before build time, advancing clock.
[   29.513747] NET: Registered protocol family 10
[   29.539415] ip_tables: (C) 2000-2006 Netfilter Core Team
[   29.680472] systemd[1]: systemd 246.1-1-arch running in system mode. (+PAM +AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid)
[   29.704035] systemd[1]: Detected architecture arm.

Welcome to Arch Linux ARM!

[   29.742098] systemd[1]: Set hostname to <alarm>.
[   31.750842] systemd[1]: Queued start job for default target Graphical Interface.
[   31.761670] random: systemd: uninitialized urandom read (16 bytes read, 31 bits of entropy available)
[   31.771563] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling.
[   31.783994] systemd[1]: (This warning is only shown for the first unit using IP firewalling.)
[   31.798164] systemd[1]: Created slice system-getty.slice.
[  OK  ] Created slice system-getty.slice.
[   31.828720] random: systemd: uninitialized urandom read (16 bytes read, 31 bits of entropy available)
[   31.840006] systemd[1]: Created slice system-modprobe.slice.
[  OK  ] Created slice system-modprobe.slice.
[   31.868667] random: systemd: uninitialized urandom read (16 bytes read, 31 bits of entropy available)
[   31.879913] systemd[1]: Created slice system-serial\x2dgetty.slice.
[  OK  ] Created slice system-serial\x2dgetty.slice.
[   31.908607] random: systemd: uninitialized urandom read (16 bytes read, 32 bits of entropy available)
[   31.919674] systemd[1]: Created slice User and Session Slice.
[  OK  ] Created slice User and Session Slice.
[   31.949079] random: systemd: uninitialized urandom read (16 bytes read, 32 bits of entropy available)
[   31.958908] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[  OK  ] Started Dispatch Password …ts to Console Directory Watch.
[   31.988649] random: systemd: uninitialized urandom read (16 bytes read, 32 bits of entropy available)
[   31.998388] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[  OK  ] Started Forward Password R…uests to Wall Directory Watch.
[   32.029335] random: systemd: uninitialized urandom read (16 bytes read, 32 bits of entropy available)
[   32.039605] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[  OK  ] Set up automount Arbitrary…s File System Automount Point.
[   32.069012] random: systemd: uninitialized urandom read (16 bytes read, 32 bits of entropy available)
[   32.078414] systemd[1]: Reached target Local Encrypted Volumes.
[  OK  ] Reached target Local Encrypted Volumes.
[   32.109179] random: systemd: uninitialized urandom read (16 bytes read, 33 bits of entropy available)
[   32.118561] systemd[1]: Reached target Paths.
[  OK  ] Reached target Paths.
[   32.138770] random: systemd: uninitialized urandom read (16 bytes read, 33 bits of entropy available)
[   32.148082] systemd[1]: Reached target Remote File Systems.
[  OK  ] Reached target Remote File Systems.
[   32.178752] systemd[1]: Reached target Slices.
[  OK  ] Reached target Slices.
[   32.198974] systemd[1]: Reached target Swap.
[  OK  ] Reached target Swap.
[   32.219772] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[  OK  ] Listening on Device-mapper event daemon FIFOs.
[   32.276272] systemd[1]: Listening on Process Core Dump Socket.
[  OK  ] Listening on Process Core Dump Socket.
[   32.311416] systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
[   32.321085] systemd[1]: Listening on Journal Socket (/dev/log).
[  OK  ] Listening on Journal Socket (/dev/log).
[   32.349993] systemd[1]: Listening on Journal Socket.
[  OK  ] Listening on Journal Socket.
[   32.380538] systemd[1]: Listening on Network Service Netlink Socket.
[  OK  ] Listening on Network Service Netlink Socket.
[   32.410159] systemd[1]: Listening on udev Control Socket.
[  OK  ] Listening on udev Control Socket.
[   32.439730] systemd[1]: Listening on udev Kernel Socket.
[  OK  ] Listening on udev Kernel Socket.
[   32.470229] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
[   32.486265] systemd[1]: Mounting POSIX Message Queue File System...
         Mounting POSIX Message Queue File System...
[   32.539515] systemd[1]: Mounting Kernel Debug File System...
         Mounting Kernel Debug File System...
[   32.650051] systemd[1]: Mounting Kernel Trace File System...
         Mounting Kernel Trace File System...
[   32.809284] systemd[1]: Mounting Temporary Directory (/tmp)...
         Mounting Temporary Directory (/tmp)...
[   32.940558] systemd[1]: Starting Create list of static device nodes for the current kernel...
         Starting Create list of st…odes for the current kernel...
[   33.203795] systemd[1]: Starting Load Kernel Module drm...
         Starting Load Kernel Module drm...
[   33.305958] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[   33.421691] systemd[1]: Condition check resulted in Load Kernel Modules being skipped.
[   33.559285] systemd[1]: Mounting FUSE Control File System...
         Mounting FUSE Control File System...
[   33.619655] systemd[1]: Condition check resulted in Kernel Configuration File System being skipped.
[   33.722498] systemd[1]: Starting Remount Root and Kernel File Systems...
         Starting Remount Root and Kernel File Systems...
[   33.799302] systemd[1]: Condition check resulted in Repartition Root Disk being skipped.
[   33.912547] systemd[1]: Starting Apply Kernel Variables...
         Starting Apply Kernel Variables...
[   34.039888] systemd[1]: Starting Coldplug All udev Devices...
         Starting Coldplug All udev Devices...
[   34.196563] systemd[1]: Mounted POSIX Message Queue File System.
[  OK  ] Mounted POSIX Message Queue File System.
[   34.310363] systemd[1]: Mounted Kernel Debug File System.
[  OK  ] Mounted Kernel Debug File System.
[   34.354544] systemd[1]: Mounted Kernel Trace File System.
[  OK  ] Mounted Kernel Trace File System.
[   34.440695] systemd[1]: Mounted Temporary Directory (/tmp).
[  OK  ] Mounted Temporary Directory (/tmp).
[   34.462458] systemd[1]: Finished Create list of static device nodes for the current kernel.
[  OK  ] Finished Create list of st… nodes for the current kernel.
[   34.535503] systemd[1]: modprobe@drm.service: Succeeded.
[   34.560563] systemd[1]: Finished Load Kernel Module drm.
[  OK  ] Finished Load Kernel Module drm.
[   34.590185] systemd[1]: Mounted FUSE Control File System.
[  OK  ] Mounted FUSE Control File System.
[   34.632963] systemd[1]: Finished Remount Root and Kernel File Systems.
[  OK  ] Finished Remount Root and Kernel File Systems.
[   34.693166] systemd[1]: Finished Apply Kernel Variables.
[  OK  ] Finished Apply Kernel Variables.
[   34.732196] systemd[1]: Condition check resulted in First Boot Wizard being skipped.
[   34.756018] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[   34.786280] systemd[1]: Starting Load/Save Random Seed...
         Starting Load/Save Random Seed...
[   34.839663] systemd[1]: Condition check resulted in Create System Users being skipped.
[   34.932504] systemd[1]: Starting Create Static Device Nodes in /dev...
         Starting Create Static Device Nodes in /dev...
[   35.413045] systemd[1]: Finished Create Static Device Nodes in /dev.
[  OK  ] Finished Create Static Device Nodes in /dev.
[   35.459842] systemd[1]: Reached target Local File Systems (Pre).
[  OK  ] Reached target Local File Systems (Pre).
[   35.479158] systemd[1]: Condition check resulted in Virtual Machine and Container Storage (Compatibility) being skipped.
[   35.518959] systemd[1]: Reached target Local File Systems.
[  OK  ] Reached target Local File Systems.
[   35.571621] systemd[1]: Started Entropy Daemon based on the HAVEGE algorithm.
[  OK  ] Started Entropy Daemon based on the HAVEGE algorithm.
[   35.620169] systemd[1]: Condition check resulted in Rebuild Dynamic Linker Cache being skipped.
[   35.707253] systemd[1]: Starting Journal Service...
         Starting Journal Service...
[   35.765449] systemd[1]: Condition check resulted in Commit a transient machine-id on disk being skipped.
[   35.931051] systemd[1]: Starting Rule-based Manager for Device Events and Files...
         Starting Rule-based Manage…for Device Events and Files...
[   36.732225] systemd[1]: Finished Coldplug All udev Devices.
[  OK  ] Finished Coldplug All udev Devices.
[**    ] (1 of 4) A start job is running for…e Events and Files (7s / 1min 34s)
[   39.619378] systemd[1]: Started Rule-based Manager for Device Events and File[  OK  ] Started Rule-based Manager for Device Events and Files.
[   39.657040] systemd[1]: Started Journal Service.
[  OK  ] Started Journal Service.
         Starting Flush Journal to Persistent Storage...
         Starting Network Service...
[***   ] (1 of 4) A start job is running for…ersistent Storage (10s / 1min 37s)
[   42.067125] MV-CESA:Could not register sha1 driver
[  *** ] (2 of 4) A start job is running for Network Service (11s / 1min 38s)
[  OK  ] Found device /dev/ttyS0.running for Network Service (12s / 1min 38s)
[  OK  ] Started Network Service.running for…/Save Random Seed (20s / 10min 3s)
[   ***] (1 of 2) A start job is running for…ersistent Storage (22s / 1min 37s)
[ ***  ] (1 of 2) A start job is running for…ersistent Storage (25s / 1min 37s)
[   57.641159] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[  OK  ] Finished Flush Journal to Persistent Storage.dom Seed (36s / 10min 3s)
         Starting Create Volatile Files and Directories...
[  OK  ] Finished Create Volatile Files and Directories.
         Starting Network Name Resolution...
         Starting Network Time Synchronization...
         Starting Update UTMP about System Boot/Shutdown...
[  OK  ] Finished Update UTMP about System Boot/Shutdown.
[    **] (2 of 3) A start job is running for…rk Name Resolution (40s / 2min 7s)
[  OK  ] Finished Load/Save Random Seed. for…rk Name Resolution (40s / 2min 7s)
[  OK  ] Started Network Time Synchronization.
[  OK  ] Reached target System Initialization.
[  OK  ] Started Daily Cleanup of Temporary Directories.
[  OK  ] Reached target System Time Set.
[  OK  ] Reached target System Time Synchronized.
[  OK  ] Started Daily verification of password and group files.
[  OK  ] Reached target Timers.
[  OK  ] Listening on D-Bus System Message Bus Socket.
[  OK  ] Reached target Sockets.
[  OK  ] Reached target Basic System.
[  OK  ] Started D-Bus System Message Bus.
         Starting User Login Management...
[  OK  ] Started Network Name Resolution.
[  OK  ] Reached target Network.
[  OK  ] Reached target Host and Network Name Lookups.
[  OK  ] Started OpenSSH Daemon.
         Starting Hostname Service...
         Starting Permit User Sessions...
[  OK  ] Finished Permit User Sessions.
[  OK  ] Started Getty on tty1.
[  OK  ] Started Serial Getty on ttyS0.
[  OK  ] Reached target Login Prompts.
[  OK  ] Started User Login Management.
[  OK  ] Reached target Multi-User System.
[  OK  ] Reached target Graphical Interface.
[  OK  ] Started Hostname Service.

Arch Linux 4.4.227-1-ARCH (ttyS0)

alarm login:

As you can see its loaded Arch and I can login with alarm alarm.

Here is the console output after creating the SD card under Linux mint root:

U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45)
Pogoplug V4

SoC:   Kirkwood 88F6192_A1
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  128 MiB
MMC:   kwsdio: 0
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Hit any key to stop autoboot:  0 

MMC rescan: current device # 0 initialized OK
** File not found /boot/uImage **
** File not found /boot/uInitrd **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
** Bad device usb 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!

Reset IDE: ide_preinit failed
** Bad device size - ide 0 **
** Bad device size - ide 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    126976 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          2048 (aligned 2048)
UBI: data offset:                4096
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=4"
UBI: MTD device size:            112 MiB
UBI: number of good PEBs:        896
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     1
UBI: available PEBs:             0
UBI: total number of reserved PEBs: 896
UBI: number of PEBs reserved for bad PEB handling: 8
UBI: max/mean erase counter: 1/0
UBIFS: recovery needed
UBIFS: recovery deferred
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: mounted read-only
UBIFS: file system size:   110850048 bytes (108252 KiB, 105 MiB, 873 LEBs)
UBIFS: journal size:       9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
UBIFS: media format:       w4/r0 (latest is w4/r0)
UBIFS: default compressor: LZO
UBIFS: reserved for root:  0 bytes (0 KiB)
Loading file 'uboot.mtd0.dockstar.original.kwb' to addr 0x00800000 with size 524288 (0x00080000)...
Done
## Starting application at 0x00800200 ...


U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16)

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 00690D60

Soc: MV88F6192 Rev 3 (DDR2)
CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 200Mhz , TClock = 166Mhz 

DRAM CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3
DRAM CS[0] base 0x00000000   size 128MB 
DRAM Total size 128MB  16bit width
Flash:  0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB

CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: PPV4A3

Streaming disabled 
Write allocate disabled


USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net:   egiga0 [PRIME], egiga1
Hit any key to stop autoboot:  0 

Loading from NAND 128MB 3,3V 8-bit, offset 0x200000
   Image Name:   Linux-2.6.31.8
   Created:      2011-09-28  19:09:20 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2080956 Bytes =  2 MB
   Load Address: 00008000
   Entry Point:  00008000
## Booting image at 00800000 ...
   Image Name:   Linux-2.6.31.8
   Created:      2011-09-28  19:09:20 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2080956 Bytes =  2 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux..................................................................................................................................... done, booting the kernel.
[    0.000000] Linux version 2.6.31.8 (afenn@kt) (gcc version 4.3.2 (sdk3.3-ct-ng-1.4.1) ) #5 Wed Sep 28 12:09:12 PDT 2011
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053177
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: Feroceon-KW
[    0.000000] Using UBoot passing parameters structure
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 root=ubi0:rootfs ubi.mtd=4,2048 rootfstype=ubifs
[    0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 128MB = 128MB total
[    0.000000] Memory: 118356KB available (3852K code, 261K data, 124K init, 0K highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:128
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Calibrating delay loop... 799.53 BogoMIPS (lpj=3997696)
[    0.230000] Mount-cache hash table entries: 512
[    0.230000] CPU: Testing write buffer coherency: ok
[    0.230000] NET: Registered protocol family 16
[    0.230000] Feroceon L2: Enabling L2
[    0.230000] Feroceon L2: Cache support initialised.
[    0.230000] 
[    0.230000] CPU Interface
[    0.230000] -------------
[    0.230000] SDRAM_CS0 ....base 00000000, size 128MB 
[    0.230000] SDRAM_CS1 ....disable
[    0.230000] SDRAM_CS2 ....disable
[    0.230000] SDRAM_CS3 ....disable
[    0.230000] PEX0_MEM ....base e0000000, size 128MB 
[    0.230000] PEX0_IO ....base f2000000, size   1MB 
[    0.230000] PEX1_MEM ....no such
[    0.230000] PEX1_IO ....no such
[    0.230000] INTER_REGS ....base f1000000, size   1MB 
[    0.230000] NFLASH_CS ....base fa000000, size   2MB 
[    0.230000] SPI_CS ....base f4000000, size  16MB 
[    0.230000] BOOT_ROM_CS ....no such
[    0.230000] DEV_BOOTCS ....no such
[    0.230000] CRYPT_ENG ....base f0000000, size   2MB 
[    0.230000] 
[    0.230000]   Marvell Development Board (LSP Version KW_LSP_5.1.3_patch18)-- SHEEVA PLUG  Soc: 88F6192 A1 LE
[    0.230000] 
[    0.230000]  Detected Tclk 166666667 and SysClk 200000000 
[    0.230000] Marvell USB EHCI Host controller #0: c403e740
[    0.730000] PEX0 interface detected Link X1
[    0.740000] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[    0.740000] pci 0000:00:01.0: PME# disabled
[    0.740000] PCI: bus0: Fast back to back transfers disabled
[    0.740000] mvPexLocalBusNumSet: ERR. Invalid PEX interface 1
[    0.750000] bio: create slab <bio-0> at 0
[    0.750000] SCSI subsystem initialized
[    0.750000] usbcore: registered new interface driver usbfs
[    0.750000] usbcore: registered new interface driver hub
[    0.750000] usbcore: registered new device driver usb
[    0.750000] NET: Registered protocol family 2
[    0.750000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.750000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    0.750000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[    0.750000] TCP: Hash tables configured (established 4096 bind 4096)
[    0.750000] TCP reno registered
[    0.750000] NET: Registered protocol family 1
[    0.750000] cpufreq: Init kirkwood cpufreq driver
[    0.760000] XOR registered 4 channels
[    0.760000] XOR 2nd invalidate WA enabled
[    0.760000] cesadev_init(c000d7fc)
[    0.760000] mvCesaInit: sessions=640, queue=64, pSram=f0000000
[    0.760000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.770000] msgmni has been set to 231
[    0.770000] alg: No test for cipher_null (cipher_null-generic)
[    0.770000] alg: No test for ecb(cipher_null) (ecb-cipher_null)
[    0.770000] alg: No test for digest_null (digest_null-generic)
[    0.770000] alg: No test for compress_null (compress_null-generic)
[    0.780000] alg: No test for stdrng (krng)
[    0.780000] alg: No test for hmac(digest_null) (hmac(digest_null-generic))
[    0.790000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.790000] io scheduler noop registered
[    0.790000] io scheduler anticipatory registered (default)
[    0.790000] Initializing ths8200_init
[    0.790000] Initializing dove_adi9889_init
[    0.810000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.810000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[    0.810000] console [ttyS0] enabled
[    0.820000] 
[    0.820000] Warning Sata is Powered Off
[    0.820000] Loading Marvell Ethernet Driver:
[    0.830000]   o Cached descriptors in DRAM
[    0.830000]   o DRAM SW cache-coherency
[    0.840000]   o 1 Giga ports supported
[    0.840000]   o Single RX Queue support - ETH_DEF_RXQ=0
[    0.840000]   o Single TX Queue support - ETH_DEF_TXQ=0
[    0.850000]   o TCP segmentation offload (TSO) supported
[    0.850000]   o Large Receive offload (LRO) supported
[    0.860000]   o Receive checksum offload supported
[    0.860000]   o Transmit checksum offload supported
[    0.870000]   o Network Fast Processing (Routing) supported - (Disabled)
[    0.880000]   o Driver ERROR statistics enabled
[    0.880000]   o Proc tool API enabled
[    0.880000]   o SKB Reuse supported - (Disabled)
[    0.890000]   o SKB Recycle supported - (Disabled)
[    0.890000]   o Rx descripors: q0=128
[    0.900000]   o Tx descripors: q0=532
[    0.900000]   o Loading network interface(s):
[    0.910000]      o register under mv88fx_eth platform
[    0.910000]      o eth0, ifindex = 2, GbE port = 0
[    0.920000] 
[    0.920000] mvFpRuleDb (c4347000): 1024 entries, 4096 bytes
[    0.920000] Counter=0, opIdx=6, overhead=16
[    0.930000] Counter=1, opIdx=2, overhead=0
[    0.930000] Counter=2, opIdx=1, overhead=18
[    0.940000] Counter=3, opIdx=2, overhead=0
[    0.940000] tun: Universal TUN/TAP device driver, 1.6
[    0.950000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.950000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit)
[    0.960000] Scanning device for bad blocks
[    1.010000] Using static partition definition
[    1.020000] Creating 5 MTD partitions on "nand_mtd":
[    1.020000] 0x000000000000-0x000000200000 : "u-boot"
[    1.030000] 0x000000200000-0x000000500000 : "uImage"
[    1.030000] 0x000000500000-0x000000800000 : "uImage2"
[    1.040000] 0x000000800000-0x000001000000 : "failsafe"
[    1.040000] 0x000001000000-0x000008000000 : "root"
[    1.050000] UBI: attaching mtd4 to ubi0
[    1.050000] UBI: physical eraseblock size:   131072 bytes (128 KiB)
[    1.060000] UBI: logical eraseblock size:    126976 bytes
[    1.070000] UBI: smallest flash I/O unit:    2048
[    1.070000] UBI: sub-page size:              512
[    1.080000] UBI: VID header offset:          2048 (aligned 2048)
[    1.080000] UBI: data offset:                4096
[    1.310000] UBI: attached mtd4 to ubi0
[    1.320000] UBI: MTD device name:            "root"
[    1.320000] UBI: MTD device size:            112 MiB
[    1.330000] UBI: number of good PEBs:        896
[    1.330000] UBI: number of bad PEBs:         0
[    1.340000] UBI: max. allowed volumes:       128
[    1.340000] UBI: wear-leveling threshold:    4096
[    1.340000] UBI: number of internal volumes: 1
[    1.350000] UBI: number of user volumes:     1
[    1.350000] UBI: available PEBs:             0
[    1.360000] UBI: total number of reserved PEBs: 896
[    1.360000] UBI: number of PEBs reserved for bad PEB handling: 8
[    1.370000] UBI: max/mean erase counter: 1/0
[    1.370000] UBI: image sequence number: 0
[    1.380000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.380000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
[    1.390000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
[    1.400000] UBI: background thread "ubi_bgt0d" started, PID 446
[    1.430000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
[    1.450000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
[    1.450000] usb usb1: configuration #1 chosen from 1 choice
[    1.460000] hub 1-0:1.0: USB hub found
[    1.460000] hub 1-0:1.0: 1 port detected
[    1.470000] xhci_hcd 0000:00:01.0: xHCI Host Controller
[    1.470000] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 2
[    1.480000] xhci_hcd 0000:00:01.0: irq 9, io mem 0xe0000000
[    1.490000] usb usb2: config 1 interface 0 altsetting 0 endpoint 0x81 has no SuperSpeed companion descriptor
[    1.500000] usb usb2: configuration #1 chosen from 1 choice
[    1.500000] hub 2-0:1.0: USB hub found
[    1.510000] hub 2-0:1.0: 4 ports detected
[    1.510000] Initializing USB Mass Storage driver...
[    1.510000] usbcore: registered new interface driver usb-storage
[    1.520000] USB Mass Storage support registered.
[    1.530000] usbcore: registered new interface driver ums-datafab
[    1.530000] usbcore: registered new interface driver ums-freecom
[    1.540000] usbcore: registered new interface driver ums-jumpshot
[    1.540000] usbcore: registered new interface driver ums-sddr09
[    1.550000] usbcore: registered new interface driver ums-sddr55
[    1.560000] usbcore: registered new interface driver ums-usbat
[    1.560000] mice: PS/2 mouse device common for all mice
[    1.570000] i2c /dev entries driver
[    1.580000] sdhci: Secure Digital Host Controller Interface driver
[    1.580000] sdhci: Copyright(c) Pierre Ossman
[    1.590000] mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
[    1.600000] usbcore: registered new interface driver usbhid
[    1.600000] usbhid: v2.6:USB HID core driver
[    1.610000] TCP cubic registered
[    1.610000] NET: Registered protocol family 17
[    1.620000] RPC: Registered udp transport module.
[    1.620000] RPC: Registered tcp transport module.
[    1.630000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.700000] UBIFS: recovery needed
[    1.790000] UBIFS: recovery completed
[    1.790000] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    1.800000] UBIFS: file system size:   110850048 bytes (108252 KiB, 105 MiB, 873 LEBs)
[    1.800000] UBIFS: journal size:       9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
[    1.810000] UBIFS: media format:       w4/r0 (latest is w4/r0)
[    1.820000] UBIFS: default compressor: lzo
[    1.820000] UBIFS: reserved for root:  0 bytes (0 KiB)
[    1.830000] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    1.830000] Freeing init memory: 124K
[    1.860000] mmc0: new high speed SDHC card at address e2cf
[    1.880000] mmcblk0: mmc0:e2cf SU08G 7.40 GiB 
[    1.880000]  mmcblk0: p1
[    4.200000] eth0: link down
[    4.200000] eth0: started
udhcpc: option -h NAME is deprecated, use -x hostname:NAME
udhcpc (v1.21.1) started
HWADDR 00 0x25 0x31 0x05 0xf5 0x25
PIP0 245
PIP1 37
cat: can't open '/etc/resolv.conf': No such file or directory
route: SIOCDELRT: No such process
grep: /etc/resolv.conf: No such file or directory
Sending discover...
[    6.140000] eth0: link up, full duplex, speed 1 Gbps
Sending discover...
Sending select for 10.0.1.231...
Lease of 10.0.1.231 obtained, lease time 86400
HWADDR 00 0x25 0x31 0x05 0xf5 0x25
PIP0 245
PIP1 37
route: SIOCDELRT: No such process
Loading gpio_keys.ko...
Loading ejectbutton.ko...
[    7.590000] IRQ 93 uses trigger mode 0; requested 3
[    7.590000] input: gpio-keys as /devices/platform/gpio-keys.0/input/input0
[    7.600000] xce_ebtn: Pogoplug series V4 eject button initialized.
[    7.740000] ufsd: module license 'Commercial product' taints kernel.
[    7.750000] Disabling lock debugging due to kernel taint
[    7.780000] ufsd: driver (8.6 (U86_S[2012-02-28-18:39:23]), LBD=ON, delalloc, ioctl) loaded at bf00c000
[    7.780000] NTFS support included
[    7.780000] Hfs+/HfsX support included
[    7.780000] For 'CloudEngines_PogoPlug_2011-08-03'
Loading rt3070sta.ko:        [    8.120000] rtusb init rt2870 --->
[    8.120000] usbcore: registered new interface driver rt2870
Success
Loading xce.ko:              [    8.140000] Cloud Engines XCE Init [Version: 3.9.0.4]
[    8.150000] XCE: CPU MEMORY MAP:
[    8.150000] XCE:   -- 0x00001000 - 0xbeffffff (3055 MB)  User Space Mappings
[    8.160000] XCE:   -- 0xbf000000 - 0xbfffffff (  16 MB)  Kernel module space
[    8.170000] XCE:   -- 0xc0000000 - 0xc7ffffff ( 128 MB)  Kernel direct-mapped ram
[    8.170000] XCE:   -- 0xc8800000 - 0xe7ffffff ( 504 MB)  Kernel vmalloc space
[    8.180000] XCE:   -- 0xe8000000 - 0xfeffffff ( 367 MB)  Kernel platform space
[    8.190000] XCE: CPU FEATURES:
[    8.190000] XCE:   -- I Cache:         enabled
[    8.200000] XCE:   -- D Cache:         enabled
[    8.200000] XCE:   -- Branch Predict:  enabled
[    8.200000] XCE:   -- MMU:             enabled
[    8.210000] XCE:   -- Alignment Abort: enabled
[    8.210000] XCE: BLPARAMS:   -- Loading properties [c4b23efc].
[    8.220000] XCE: BLPARAMS:   -- MTD @ [c4343000].
[    8.230000] XCE: BLPARAMS: Locating parameter block...
[    8.230000] XCE: BLPARAMS: reading 2048 bytes @ a0000
[    8.240000] XCE: Loaded Property Size: 2048
[    8.240000] XCE:    - 'cesvcid' -> '2W8WWQ4MZYQW3RPV68JJC7JZES'
[    8.250000] XCE:    - 'ceboardver' -> 'PPV4A3'
[    8.250000] XCE:   -- ICache Prefetch: enabled
[    8.260000] XCE:   -- DCache Prefetch: enabled
[    8.260000] XCE:   -- L2 Cache:        enabled
[    8.270000] XCE:   -- L2 Prefetch:     disabled
[    8.270000] XCE:   -- L2 Writethrough: disabled
[    8.280000] XCE:   -- Write Allocate:  disabled
[    8.280000] XCE:   -- Streaming:       disabled
[    8.280000] XCE: Current GPIO State:
[    8.290000] XCE:  GPIO L OUT:    0x21400000
[    8.290000] XCE:  GPIO L OE:     0x30000000
[    8.300000] XCE:  GPIO L BLINK:  0x00000000
[    8.300000] XCE:  GPIO L POL:    0x00000000
[    8.300000] XCE:  GPIO L IN:     0x01400000
[    8.310000] XCE:  GPIO H OUT:    0xfffc7fff
[    8.310000] XCE:  GPIO H OE:     0x00000000
[    8.320000] XCE:  GPIO H BLINK:  0x00004000
[    8.320000] XCE:  GPIO H POL:    0x00000000
[    8.330000] XCE:  GPIO H IN:     0x0000000f
Success
Starting hbplug:             Success
/ # [    8.510000] XCE: BLPARAMS:   -- Loading properties [c4b07ecc].
[    8.520000] XCE: BLPARAMS:   -- MTD @ [c4343000].
[    8.520000] XCE: BLPARAMS: Locating parameter block...
[    8.530000] XCE: BLPARAMS: reading 2048 bytes @ a0000
[    8.530000] XCE: BLPARAMS: reading 2048 bytes @ a0800
[    8.540000] XCE: BLPARAMS: reading 2048 bytes @ a1000
[    8.550000] XCE: BLPARAMS: reading 2048 bytes @ a1800
[   16.780000] XCE: XCE: LED -> DISCONNECTED
[   16.950000] EXT3-fs: INFO: recovery required on readonly filesystem.
[   16.950000] EXT3-fs: write access will be enabled during recovery.
[   18.510000] kjournald starting.  Commit interval 5 seconds
[   18.520000] EXT3-fs: recovery complete.
[   18.530000] EXT3-fs: mounted filesystem with writeback data mode.
[   18.780000] kjournald starting.  Commit interval 5 seconds
[   18.790000] EXT3 FS on mmcblk0p1, internal journal
[   18.790000] EXT3-fs: mounted filesystem with writeback data mode.

It says it can't find a kernel image, goes into recovery but doesn't fully load ArchLinux.

Here is my fw_printenv from ssh also

/tmp # /tmp/fw_printenv
baudrate=115200
bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot
bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot;
bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot;
bootdelay=10
console=ttyS0,115200
device=0:1
ethact=egiga0
if_netconsole=ping $serverip
led_error=orange blinking
led_exit=green off
led_init=green blinking
mainlineLinux=yes
mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
mmc_init=mmc rescan
mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage
mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd
mmc_root=/dev/mmcblk0p1
mtdids=nand0=orion_nand
partition=nand0,2
preboot_nc=run if_netconsole start_netconsole
rootdelay=10
rootfstype=ext3
sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
sata_init=ide reset
sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage
sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd
sata_root=/dev/sda1
set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
usb_init=usb start
usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage
usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd
usb_root=/dev/sda1
ethaddr=00:25:31:05:f5:25
arcNumber=3960
machid=F78
usb_rootfstype=ext3
mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
bootcmd_pogo=if ubi part root 2048 && ubifsmount ubi:rootfs && ubifsload 0x800000 uboot.mtd0.dockstar.original.kwb ; then go 0x800200; fi
bootcmd=run bootcmd_mmc; run bootcmd_usb; run bootcmd_sata; run bootcmd_pogo; reset
serverip=10.0.1.231
ipaddr=10.0.1.220

Any help would be appreciated.

Rhodess,

> At this point I'm wondering if the ArchLinux
> version is simply too new for the Pogoplug
> hardware and should I be trying to load an older
> version?

Not the reason. Besides, the successful boot shows the kernel was built recently (6 months ago):

[    0.000000] Linux version 4.4.227-1-ARCH (builduser@leming) (gcc version 9.3.0 (GCC) ) #1 PREEMPT Sat Jun 13 04:13:48 UTC 2020

The failed boot showed that the SD rootfs created in Mint simply was not prepared correctly:

** File not found /boot/uImage **

When you create the rootfs on SD card using Mint, pay attention to these:

- You must be root user.
- use command line fdisk, clear the partitions, and create a new Ext3 partition. Don't use the GUI to do this.
- mount it, and untar the Arch rootfs to it.
- Do several sync commands.
- Unmount the card.


In the event that you used a rootfs tarbal other than one with kernel "Linux version 4.4.227-1-ARCH", list the /boot folder after you create it and post here.

Assuming the card is mounted at /media/sdb1:

ls -latr /media/sdb1/boot

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)



Edited 1 time(s). Last edit at 01/10/2021 04:55PM by bodhi.

Thanks Bodhi, the only thing different I did was sync only once.

Here was my process:

Reboot linux Mint
CTRL+ALT+F4
Login as root to command prompt

#Partition SD Card
fdisk /dev/mmcblk0

p # list current partitions
o # to delete all partitions
n # new partition
p # primary partition
1 (one) # first partition
<enter> # default start block
<enter> # default end block 
+4G # create a 4GB partition
w # write new partition to disk

#format newly created partition
mke2fs -L rootfs -j /dev/mmcblk0p1

#create mount point
mkdir /tmp/mnt

#mount SD Card
mount /dev/mmcblk0p1 /tmp/mnt

#cd /tmp/mnt
wget http://archlinuxarm.org/os/ArchLinuxARM-kirkwood-latest.tar.gz 
tar -xzvf ArchLinuxARM-kirkwood-latest.tar.gz
rm ArchLinuxARM-kirkwood-latest.tar.gz

#Sync and reboot
sync
cd ..
umount /tmp/mnt
reboot

Is there anything I missed other than multiple sync commands?

Rhodess,

> #mount SD Card
> mount /dev/mmcblk0p1 /tmp/mnt

At this point, list the mount points to check if the partition is OK

mount

And list the /boot folder

ls -lart /tmp/mnt/boot

========

BTW, I suspect that this is the problem

mke2fs -L rootfs -j /dev/mmcblk0p1

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)



Edited 2 time(s). Last edit at 01/10/2021 05:29PM by bodhi.

Yep that's it. -- No such file or directory.
I will unmount and try again. I also noticed during partitioning there was a mmc_erase: erase error -110, status 0x0 and it discarded blocks, but partitioned OK, or so I thought. I will try another SD card and a USB also, until I see one that shows the boot folder.

Thanks for the help bohdi

PS It doesn't seem to create the boot folder, I tried with 3 SD cards so far



Edited 1 time(s). Last edit at 01/10/2021 06:30PM by Rhodess.

Bodhi,

I mounted by SD card in another machine and get the following:

rhodess-HP rhodess # cd /media/rhodess/rootfs
rhodess-HP rootfs # ls -lart /
total 116
drwxr-xr-x   2 root root  4096 Nov 24  2017 srv
drwx------   2 root root 16384 Mar  9  2018 lost+found
drwxr-xr-x   2 root root  4096 Mar  9  2018 cdrom
drwxr-xr-x   3 root root  4096 Mar  9  2018 home
drwxr-xr-x   3 root root  4096 Mar 10  2018 media
drwxr-xr-x  12 root root  4096 Mar 11  2018 var
drwxr-xr-x   9 root root  4096 Oct 28  2018 opt
drwxr-xr-x   3 root root  4096 Nov 19  2018 .config
drwx------  11 root root  4096 Dec 15  2018 root
drwxr-xr-x  12 root root  4096 Apr 13  2019 usr
drwxr-xr-x  26 root root  4096 Jul 19 23:10 lib
drwxr-xr-x   2 root root  4096 Jul 19 23:10 lib64
drwxr-xr-x   2 root root  4096 Oct 30 23:05 bin
drwxr-xr-x   2 root root 12288 Oct 30 23:06 sbin
lrwxrwxrwx   1 root root    31 Jan  8 19:26 vmlinuz.old -> boot/vmlinuz-4.15.0-128-generic
lrwxrwxrwx   1 root root    31 Jan  8 19:26 vmlinuz -> boot/vmlinuz-4.15.0-129-generic
lrwxrwxrwx   1 root root    34 Jan  8 19:26 initrd.img.old -> boot/initrd.img-4.15.0-128-generic
lrwxrwxrwx   1 root root    34 Jan  8 19:26 initrd.img -> boot/initrd.img-4.15.0-129-generic
drwxr-xr-x  24 root root  4096 Jan  8 19:26 ..
drwxr-xr-x  24 root root  4096 Jan  8 19:26 .
drwxr-xr-x   3 root root 12288 Jan  8 19:27 boot
drwxr-xr-x   9 root root  4096 Jan 11 00:52 timeshift
dr-xr-xr-x 242 root root     0 Jan 11 20:40 proc
dr-xr-xr-x  13 root root     0 Jan 11 20:40 sys
drwxr-xr-x  21 root root  4600 Jan 11 20:42 dev
drwxr-xr-x  35 root root  1060 Jan 11 20:44 run
drwxr-xr-x 158 root root 12288 Jan 11 21:05 etc
drwxrwxrwt  14 root root  4096 Jan 11 21:17 tmp
rhodess-HP rootfs # ls -lart /boot
total 2348984
-rw-r--r--  1 root root   184840 Jan 28  2016 memtest86+_multiboot.bin
-rw-r--r--  1 root root   184380 Jan 28  2016 memtest86+.elf
-rw-r--r--  1 root root   182704 Jan 28  2016 memtest86+.bin
-rw-------  1 root root  3722376 Oct 10  2017 System.map-4.10.0-38-generic
-rw-r--r--  1 root root   204970 Oct 10  2017 config-4.10.0-38-generic
-rw-r--r--  1 root root  1443962 Oct 10  2017 abi-4.10.0-38-generic
-rw-r--r--  1 root root  7407392 Nov 24  2017 vmlinuz-4.10.0-38-generic
-rw-------  1 root root  7710896 Feb 16  2018 vmlinuz-4.13.0-36-generic
-rw-------  1 root root  3879946 Feb 16  2018 System.map-4.13.0-36-generic
-rw-r--r--  1 root root     2850 Feb 16  2018 retpoline-4.13.0-36-generic
-rw-r--r--  1 root root   213220 Feb 16  2018 config-4.13.0-36-generic
-rw-r--r--  1 root root  1501359 Feb 16  2018 abi-4.13.0-36-generic
-rw-------  1 root root  7711632 Mar  7  2018 vmlinuz-4.13.0-37-generic
-rw-------  1 root root  3879989 Mar  7  2018 System.map-4.13.0-37-generic
-rw-r--r--  1 root root     2850 Mar  7  2018 retpoline-4.13.0-37-generic
-rw-r--r--  1 root root   213220 Mar  7  2018 config-4.13.0-37-generic
-rw-r--r--  1 root root  1501359 Mar  7  2018 abi-4.13.0-37-generic
-rw-------  1 root root  7712208 Mar 14  2018 vmlinuz-4.13.0-38-generic
-rw-------  1 root root  3880619 Mar 14  2018 System.map-4.13.0-38-generic
-rw-r--r--  1 root root     2850 Mar 14  2018 retpoline-4.13.0-38-generic
-rw-r--r--  1 root root   213220 Mar 14  2018 config-4.13.0-38-generic
-rw-r--r--  1 root root  1501474 Mar 14  2018 abi-4.13.0-38-generic
-rw-------  1 root root  7711664 May  3  2018 vmlinuz-4.13.0-41-generic
-rw-------  1 root root  3882700 May  3  2018 System.map-4.13.0-41-generic
-rw-r--r--  1 root root      255 May  3  2018 retpoline-4.13.0-41-generic
-rw-r--r--  1 root root   213220 May  3  2018 config-4.13.0-41-generic
-rw-r--r--  1 root root  1501416 May  3  2018 abi-4.13.0-41-generic
-rw-------  1 root root  7713296 May 17  2018 vmlinuz-4.13.0-43-generic
-rw-------  1 root root  3884045 May 17  2018 System.map-4.13.0-43-generic
-rw-r--r--  1 root root      255 May 17  2018 retpoline-4.13.0-43-generic
-rw-r--r--  1 root root   213220 May 17  2018 config-4.13.0-43-generic
-rw-r--r--  1 root root  1501659 May 17  2018 abi-4.13.0-43-generic
-rw-------  1 root root  7712560 May 30  2018 vmlinuz-4.13.0-45-generic
-rw-------  1 root root  3883942 May 30  2018 System.map-4.13.0-45-generic
-rw-r--r--  1 root root      255 May 30  2018 retpoline-4.13.0-45-generic
-rw-r--r--  1 root root   213220 May 30  2018 config-4.13.0-45-generic
-rw-r--r--  1 root root  1501528 May 30  2018 abi-4.13.0-45-generic
-rw-------  1 root root  4039610 Jun 15  2018 System.map-4.15.0-24-generic
-rw-r--r--  1 root root        0 Jun 15  2018 retpoline-4.15.0-24-generic
-rw-r--r--  1 root root   216815 Jun 15  2018 config-4.15.0-24-generic
-rw-r--r--  1 root root  1537161 Jun 15  2018 abi-4.15.0-24-generic
-rw-------  1 root root  8102264 Jun 18  2018 vmlinuz-4.15.0-24-generic
-rw-------  1 root root  4039561 Jul 18  2018 System.map-4.15.0-29-generic
-rw-r--r--  1 root root        0 Jul 18  2018 retpoline-4.15.0-29-generic
-rw-r--r--  1 root root   216815 Jul 18  2018 config-4.15.0-29-generic
-rw-r--r--  1 root root  1537161 Jul 18  2018 abi-4.15.0-29-generic
-rw-------  1 root root  8101496 Jul 18  2018 vmlinuz-4.15.0-29-generic
-rw-------  1 root root  4039601 Jul 26  2018 System.map-4.15.0-30-generic
-rw-r--r--  1 root root        0 Jul 26  2018 retpoline-4.15.0-30-generic
-rw-r--r--  1 root root   216815 Jul 26  2018 config-4.15.0-30-generic
-rw-r--r--  1 root root  1537161 Jul 26  2018 abi-4.15.0-30-generic
-rw-------  1 root root  8101272 Aug  6  2018 vmlinuz-4.15.0-30-generic
-rw-------  1 root root  4041375 Aug 15  2018 System.map-4.15.0-33-generic
-rw-r--r--  1 root root        0 Aug 15  2018 retpoline-4.15.0-33-generic
-rw-r--r--  1 root root   216913 Aug 15  2018 config-4.15.0-33-generic
-rw-r--r--  1 root root  1537455 Aug 15  2018 abi-4.15.0-33-generic
-rw-------  1 root root  8108600 Aug 16  2018 vmlinuz-4.15.0-33-generic
-rw-------  1 root root  4043167 Aug 28  2018 System.map-4.15.0-34-generic
-rw-r--r--  1 root root        0 Aug 28  2018 retpoline-4.15.0-34-generic
-rw-r--r--  1 root root   216913 Aug 28  2018 config-4.15.0-34-generic
-rw-r--r--  1 root root  1537610 Aug 28  2018 abi-4.15.0-34-generic
-rw-------  1 root root  8114136 Aug 29  2018 vmlinuz-4.15.0-34-generic
-rw-------  1 root root  4045599 Sep 25  2018 System.map-4.15.0-36-generic
-rw-r--r--  1 root root        0 Sep 25  2018 retpoline-4.15.0-36-generic
-rw-r--r--  1 root root   216962 Sep 25  2018 config-4.15.0-36-generic
-rw-r--r--  1 root root  1537821 Sep 25  2018 abi-4.15.0-36-generic
-rw-------  1 root root  8119672 Sep 26  2018 vmlinuz-4.15.0-36-generic
-rw-------  1 root root  4046116 Oct 10  2018 System.map-4.15.0-38-generic
-rw-r--r--  1 root root        0 Oct 10  2018 retpoline-4.15.0-38-generic
-rw-r--r--  1 root root   216991 Oct 10  2018 config-4.15.0-38-generic
-rw-r--r--  1 root root  1537997 Oct 10  2018 abi-4.15.0-38-generic
-rw-------  1 root root  8120984 Oct 11  2018 vmlinuz-4.15.0-38-generic
-rw-------  1 root root  4046310 Oct 24  2018 System.map-4.15.0-39-generic
-rw-r--r--  1 root root        0 Oct 24  2018 retpoline-4.15.0-39-generic
-rw-r--r--  1 root root   217026 Oct 24  2018 config-4.15.0-39-generic
-rw-r--r--  1 root root  1537997 Oct 24  2018 abi-4.15.0-39-generic
-rw-------  1 root root  8121560 Oct 25  2018 vmlinuz-4.15.0-39-generic
-rw-------  1 root root  4047229 Nov 19  2018 System.map-4.15.0-42-generic
-rw-r--r--  1 root root        0 Nov 19  2018 retpoline-4.15.0-42-generic
-rw-r--r--  1 root root   217026 Nov 19  2018 config-4.15.0-42-generic
-rw-r--r--  1 root root  1538114 Nov 19  2018 abi-4.15.0-42-generic
-rw-------  1 root root  8119832 Nov 20  2018 vmlinuz-4.15.0-42-generic
-rw-------  1 root root  4047366 Dec  7  2018 System.map-4.15.0-43-generic
-rw-r--r--  1 root root   217026 Dec  7  2018 config-4.15.0-43-generic
-rw-------  1 root root  8119768 Dec  8  2018 vmlinuz-4.15.0-43-generic
-rw-------  1 root root  4049376 Feb 12  2019 System.map-4.15.0-46-generic
-rw-r--r--  1 root root   217004 Feb 12  2019 config-4.15.0-46-generic
-rw-------  1 root root  8125784 Feb 15  2019 vmlinuz-4.15.0-46-generic
-rw-------  1 root root  4049889 Mar 15  2019 System.map-4.15.0-47-generic
-rw-r--r--  1 root root   217004 Mar 15  2019 config-4.15.0-47-generic
-rw-------  1 root root  8130328 Mar 18  2019 vmlinuz-4.15.0-47-generic
-rw-------  1 root root  4050903 Jun 24  2019 System.map-4.15.0-54-generic
-rw-r--r--  1 root root   217286 Jun 24  2019 config-4.15.0-54-generic
-rw-------  1 root root  8140856 Jun 25  2019 vmlinuz-4.15.0-54-generic
-rw-------  1 root root  4062077 Sep 18  2019 System.map-4.15.0-65-generic
-rw-r--r--  1 root root   217370 Sep 18  2019 config-4.15.0-65-generic
-rw-------  1 root root  8181016 Sep 19  2019 vmlinuz-4.15.0-65-generic
-rw-------  1 root root  4062584 Oct  1  2019 System.map-4.15.0-66-generic
-rw-r--r--  1 root root   217370 Oct  1  2019 config-4.15.0-66-generic
-rw-------  1 root root  8181656 Oct  3  2019 vmlinuz-4.15.0-66-generic
-rw-------  1 root root  4066237 Jan 20  2020 System.map-4.15.0-76-generic
-rw-r--r--  1 root root   217503 Jan 20  2020 config-4.15.0-76-generic
-rw-------  1 root root  8187320 Jan 21  2020 vmlinuz-4.15.0-76-generic
-rw-------  1 root root  4067466 Feb 12  2020 System.map-4.15.0-88-generic
-rw-r--r--  1 root root   217503 Feb 12  2020 config-4.15.0-88-generic
-rw-------  1 root root  8193496 Feb 12  2020 vmlinuz-4.15.0-88-generic
-rw-------  1 root root  4067536 Feb 28  2020 System.map-4.15.0-91-generic
-rw-r--r--  1 root root   217465 Feb 28  2020 config-4.15.0-91-generic
-rw-------  1 root root  8193432 Mar  1  2020 vmlinuz-4.15.0-91-generic
-rw-------  1 root root  4068326 Apr  1  2020 System.map-4.15.0-96-generic
-rw-r--r--  1 root root   217465 Apr  1  2020 config-4.15.0-96-generic
-rw-------  1 root root  8191544 Apr  6  2020 vmlinuz-4.15.0-96-generic
-rw-------  1 root root  4069610 Apr 22  2020 System.map-4.15.0-99-generic
-rw-r--r--  1 root root   217466 Apr 22  2020 config-4.15.0-99-generic
-rw-------  1 root root  8202744 Apr 28  2020 vmlinuz-4.15.0-99-generic
-rw-------  1 root root  4071267 Jun  4  2020 System.map-4.15.0-106-generic
-rw-r--r--  1 root root   217481 Jun  4  2020 config-4.15.0-106-generic
-rw-------  1 root root  8199584 Jun  9  2020 vmlinuz-4.15.0-106-generic
-rw-------  1 root root  4071450 Jun 12  2020 System.map-4.15.0-107-generic
-rw-r--r--  1 root root   217481 Jun 12  2020 config-4.15.0-107-generic
-rw-------  1 root root  8198944 Jun 13  2020 vmlinuz-4.15.0-107-generic
-rw-r--r--  1 root root 58593529 Jun 24  2020 initrd.img-4.15.0-96-generic
-rw-r--r--  1 root root 58589670 Jun 24  2020 initrd.img-4.15.0-91-generic
-rw-r--r--  1 root root 58591151 Jun 24  2020 initrd.img-4.15.0-88-generic
-rw-r--r--  1 root root 58577118 Jun 24  2020 initrd.img-4.15.0-76-generic
-rw-r--r--  1 root root 58569512 Jun 24  2020 initrd.img-4.15.0-66-generic
-rw-r--r--  1 root root 58569170 Jun 24  2020 initrd.img-4.15.0-65-generic
-rw-r--r--  1 root root 58555742 Jun 24  2020 initrd.img-4.15.0-54-generic
-rw-r--r--  1 root root 58554719 Jun 24  2020 initrd.img-4.15.0-47-generic
-rw-r--r--  1 root root 58555784 Jun 24  2020 initrd.img-4.15.0-46-generic
-rw-r--r--  1 root root 58533495 Jun 24  2020 initrd.img-4.15.0-43-generic
-rw-r--r--  1 root root 58532311 Jun 24  2020 initrd.img-4.15.0-42-generic
-rw-r--r--  1 root root 58534552 Jun 24  2020 initrd.img-4.15.0-39-generic
-rw-r--r--  1 root root 58529186 Jun 24  2020 initrd.img-4.15.0-38-generic
-rw-r--r--  1 root root 58536608 Jun 24  2020 initrd.img-4.15.0-36-generic
-rw-r--r--  1 root root 58520792 Jun 24  2020 initrd.img-4.15.0-34-generic
-rw-r--r--  1 root root 58525919 Jun 24  2020 initrd.img-4.15.0-33-generic
-rw-r--r--  1 root root 58514266 Jun 24  2020 initrd.img-4.15.0-30-generic
-rw-r--r--  1 root root 58512611 Jun 24  2020 initrd.img-4.15.0-29-generic
-rw-r--r--  1 root root 58517771 Jun 24  2020 initrd.img-4.15.0-24-generic
-rw-r--r--  1 root root 55336808 Jun 24  2020 initrd.img-4.13.0-45-generic
-rw-r--r--  1 root root 55337678 Jun 24  2020 initrd.img-4.13.0-43-generic
-rw-r--r--  1 root root 55336549 Jun 24  2020 initrd.img-4.13.0-41-generic
-rw-r--r--  1 root root 55330731 Jun 24  2020 initrd.img-4.13.0-38-generic
-rw-r--r--  1 root root 55327630 Jun 24  2020 initrd.img-4.13.0-37-generic
-rw-r--r--  1 root root 55332572 Jun 24  2020 initrd.img-4.13.0-36-generic
-rw-r--r--  1 root root 47481833 Jun 24  2020 initrd.img-4.10.0-38-generic
-rw-r--r--  1 root root 58590214 Jun 24  2020 initrd.img-4.15.0-99-generic
-rw-r--r--  1 root root 58611584 Jun 24  2020 initrd.img-4.15.0-106-generic
-rw-r--r--  1 root root 58615311 Jul 19 23:15 initrd.img-4.15.0-107-generic
-rw-------  1 root root  4072752 Sep  5 21:00 System.map-4.15.0-117-generic
-rw-r--r--  1 root root   217477 Sep  5 21:00 config-4.15.0-117-generic
-rw-------  1 root root  8208384 Sep  6 14:03 vmlinuz-4.15.0-117-generic
-rw-------  1 root root  4074286 Oct 15 13:23 System.map-4.15.0-122-generic
-rw-r--r--  1 root root   217509 Oct 15 13:23 config-4.15.0-122-generic
-rw-------  1 root root  8205536 Oct 16 02:58 vmlinuz-4.15.0-122-generic
-rw-------  1 root root  4074286 Oct 21 12:24 System.map-4.15.0-123-generic
-rw-r--r--  1 root root   217509 Oct 21 12:24 config-4.15.0-123-generic
-rw-r--r--  1 root root 58625888 Oct 30 23:42 initrd.img-4.15.0-117-generic
-rw-r--r--  1 root root 58626379 Oct 30 23:42 initrd.img-4.15.0-122-generic
-rw-------  1 root root  8205440 Nov 10 12:33 vmlinuz-4.15.0-123-generic
-rw-r--r--  1 root root 59081139 Nov 20 22:16 initrd.img-4.15.0-123-generic
-rw-------  1 root root  4074563 Dec  9 15:13 System.map-4.15.0-128-generic
-rw-r--r--  1 root root   217466 Dec  9 15:13 config-4.15.0-128-generic
-rw-------  1 root root  8210048 Dec 11 10:33 vmlinuz-4.15.0-128-generic
-rw-------  1 root root  4076328 Dec 16 03:06 System.map-4.15.0-129-generic
-rw-r--r--  1 root root   217466 Dec 16 03:06 config-4.15.0-129-generic
-rw-------  1 root root  8213536 Dec 17 06:23 vmlinuz-4.15.0-129-generic
-rw-r--r--  1 root root 59088863 Dec 28 21:55 initrd.img-4.15.0-128-generic
drwxr-xr-x 24 root root     4096 Jan  8 19:26 ..
-rw-r--r--  1 root root 59092419 Jan  8 19:27 initrd.img-4.15.0-129-generic
drwxr-xr-x  3 root root    12288 Jan  8 19:27 .
drwxr-xr-x  5 root root     4096 Jan  8 19:27 grub
rhodess-HP rootfs #

It looks like the are named differently in the boot folder could that be the issue?

I saw on the ArchLnux site mention of the newer ArchLnux kernels not loading if the mbr has zeros in sector 1B8-1BB, so I checked that and its fine.

Is there a link to a known good image that I can write to an SD to see if that works?

Rhodess,

You've listed the wrong folders. Should be

cd /media/rhodess/rootfs

ls -lart ./rootfs
ls -lart ./boot

or just

ls -lart /media/rhodess/rootfs
ls -lart /media/rhodess/rootfs/boot

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Here is what I get from that:

rhodess-HP rhodess # cd /media/rhodess/rootfs
rhodess-HP rootfs # ls -lart ./rootfs
ls: cannot access './rootfs': No such file or directory
rhodess-HP rootfs # ls -lart ./boot
total 12876
drwxr-xr-x 18 root root    4096 Dec 31  1969 ..
-rwxr-xr-x  1 root root 4955992 Aug  8 23:27 zImage
drwxr-xr-x  3 root root    4096 Aug  9 13:54 .
-rw-r--r--  1 root root 8180393 Aug  9 13:54 initramfs-linux.img
drwxr-xr-x  2 root root   12288 Jan 10 13:14 dtbs
rhodess-HP rootfs # 

Rhodess,

Quote

> rhodess-HP rootfs # ls -lart ./boot
> total 12876
> drwxr-xr-x 18 root root 4096 Dec 31 1969 ..
> -rwxr-xr-x 1 root root 4955992 Aug 8 23:27
> zImage
> drwxr-xr-x 3 root root 4096 Aug 9 13:54 .
> -rw-r--r-- 1 root root 8180393 Aug 9 13:54
> initramfs-linux.img
> drwxr-xr-x 2 root root 12288 Jan 10 13:14 dtbs
> rhodess-HP rootfs #

Yes.This Arch rootfs is newer, was the reason. Apparently, in this version, Arch ARM has switched to booting with zImage for this box.

So now the mmc boot envs must be adjusted to conform to that.

Your u-boot is also old. So the envs are not good enough for booting witht the new rootfs.

Let me write a few steps in the next post.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Thanks bodhi, I appreciate the help

Rhodess,


Mount the SD card rootfs on another Linux box like you did. Assuming it is mounted at /media/rhodess/rootfs.

cd /media/rhodess/rootfs/boot

Get the file name of this Pogolug V4 DTB file

ls -l ./dtbs/*pogo*

Assuming the file name is kirkwood-pogoplug_v4.dtb. If it was name differently in this Arch rootfs then use that name below

cp -a zImage zImage.fdt
cat ./dtbs/kirkwood-pogoplug_v4.dtb  >> zImage.fdt
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n ArchLinuxARM -d zImage.fdt  uImage
sync

And umount the SD card. Bring it back to the Pogo V4 and start the box.

====

Note that I don't know the kernel version in this rootfs so I name it ArchLinuxARM in the mkimage command above. To keep track of the correct version, you should regenerate the uImage again after you has booted successfully into Arch.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Thanks bodhi,

I will try that tomorrow night after work

Hi bodhi,

Almost there!

It looks like its loading, but now I'm getting a kernel panic and it crashes

U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45)
Pogoplug V4

SoC:   Kirkwood 88F6192_A1
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  128 MiB
MMC:   kwsdio: 0
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Hit any key to stop autoboot: 0 

MMC rescan: current device # 0 initialized OK
4966364 bytes read in 1451 ms (3.3 MiB/s)
** File not found /boot/uInitrd **
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   ArchLinuxARM
   Created:      2021-01-13  14:45:08 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4966300 Bytes = 4.7 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
Using machid 0xf78 from environment

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.8.0-1-ARCH (builduser@leming) (armv5tel-unknown-linux-gnueabi-gcc (GCC) 9.3.0, GNU ld (GNU Binutils) 2.34) #1 Sun Aug 9 03:29:09 UTC 2020
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] OF: fdt: Machine model: Cloud Engines PogoPlug Series 4
[    0.000000] Memory policy: Data cache writeback
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p1 rootdelay=10 rootfstype=ext3 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 115388K/131072K available (9771K kernel code, 349K rwdata, 3404K rodata, 336K init, 197K bss, 15684K reserved, 0K cma-reserved)
[    0.000000] random: get_random_u32 called from cache_random_seq_create+0x80/0x134 with crng_init=0
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[    0.000013] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[    0.000061] Switching to timer-based delay loop, resolution 6ns
[    0.000400] Console: colour dummy device 80x30
[    0.000468] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666)
[    0.000499] pid_max: default: 32768 minimum: 301
[    0.001191] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.001224] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.003215] CPU: Testing write buffer coherency: ok
[    0.004612] Setting up static identity map for 0x8400 - 0x847c
[    0.005002] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[    0.005910] devtmpfs: initialized
[    0.011090] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.011129] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.011497] pinctrl core: initialized pinctrl subsystem
[    0.012570] thermal_sys: Registered thermal governor 'step_wise'
[    0.013626] NET: Registered protocol family 16
[    0.014491] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.015536] audit: initializing netlink subsys (disabled)
[    0.017216] cpuidle: using governor ladder
[    0.017240] cpuidle: using governor menu
[    0.017933] Feroceon L2: Enabling L2
[    0.017992] Feroceon L2: Cache support initialised.
[    0.030316] No ATAGs?
[    0.030852] Serial: AMBA PL011 UART driver
[    0.041062] audit: type=2000 audit(0.010:1): state=initialized audit_enabled=0 res=1
[    0.047884] AT91: Could not find identification node
[    0.048381] vgaarb: loaded
[    0.048970] SCSI subsystem initialized
[    0.049602] usbcore: registered new interface driver usbfs
[    0.049672] usbcore: registered new interface driver hub
[    0.049740] usbcore: registered new device driver usb
[    0.050240] pps_core: LinuxPPS API ver. 1 registered
[    0.050252] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.050284] PTP clock support registered
[    0.050631] Advanced Linux Sound Architecture Driver Initialized.
[    0.051855] clocksource: Switched to clocksource orion_clocksource
[    0.052263] VFS: Disk quotas dquot_6.6.0
[    0.052364] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.063921] NET: Registered protocol family 2
[    0.064866] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.064958] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.064988] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.065014] TCP: Hash tables configured (established 1024 bind 1024)
[    0.065516] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.065551] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.065838] NET: Registered protocol family 1
[    0.066442] RPC: Registered named UNIX socket transport module.
[    0.066455] RPC: Registered udp transport module.
[    0.066462] RPC: Registered tcp transport module.
[    0.066469] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.066484] PCI: CLS 0 bytes, default 32
[    0.069010] Initialise system trusted keyrings
[    0.069259] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[    0.080766] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.082364] NFS: Registering the id_resolver key type
[    0.082403] Key type id_resolver registered
[    0.082412] Key type id_legacy registered
[    0.082434] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.082481] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.083271] fuse: init (API version 7.31)
[    0.276296] Key type asymmetric registered
[    0.276314] Asymmetric key parser 'x509' registered
[    0.276383] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    0.276541] io scheduler mq-deadline registered
[    0.276554] io scheduler kyber registered
[    0.276937] io scheduler bfq registered
[    0.278684] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[    0.281211] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00
[    0.281236] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.281253] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[    0.281268] pci_bus 0000:00: root bus resource [io  0x1000-0xeffff]
[    0.281404] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400
[    0.281453] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[    0.283056] PCI: bus0: Fast back to back transfers disabled
[    0.283081] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.283285] pci 0000:01:00.0: [1b73:1009] type 00 class 0x0c0330
[    0.283339] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x0000ffff 64bit]
[    0.283367] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit]
[    0.283393] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit]
[    0.283497] pci 0000:01:00.0: supports D1
[    0.283512] pci 0000:01:00.0: PME# supported from D0 D1 D3hot
[    0.283559] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[    0.313136] PCI: bus1: Fast back to back transfers disabled
[    0.313163] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    0.313445] pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe00fffff]
[    0.313466] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0100000-0xe01007ff pref]
[    0.313490] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff 64bit]
[    0.313518] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0010000-0xe0010fff 64bit]
[    0.313545] pci 0000:01:00.0: BAR 4: assigned [mem 0xe0011000-0xe0011fff 64bit]
[    0.313569] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.313589] pci 0000:00:01.0:   bridge window [mem 0xe0000000-0xe00fffff]
[    0.313669] pci 0000:00:01.0: enabling device (0140 -> 0142)
[    0.313699] pci 0000:01:00.0: enabling device (0140 -> 0142)
[    0.314547] mv_xor f1060800.xor: Marvell shared XOR driver
[    0.372998] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    0.373402] mv_xor f1060900.xor: Marvell shared XOR driver
[    0.432976] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    0.433610] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.435234] printk: console [ttyS0] disabled
[    0.435380] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 10416666) is a 16550A
[    1.184119] printk: console [ttyS0] enabled
[    1.193599] brd: module loaded
[    1.207581] loop: module loaded
[    1.212020] sata_mv f1080000.sata: slots 32 ports 1
[    1.218821] scsi host0: sata_mv
[    1.222458] ata1: SATA max UDMA/133 irq 32
[    1.227797] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[    1.234168] nand: Hynix H27U1G8F2BTR-BC
[    1.237989] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.245562] Scanning device for bad blocks
[    1.364418] 5 cmdlinepart partitions found on MTD device orion_nand
[    1.370654] Creating 5 MTD partitions on "orion_nand":
[    1.375795] 0x000000000000-0x000000200000 : "u-boot"
[    1.382949] 0x000000200000-0x000000500000 : "uImage"
[    1.389569] 0x000000500000-0x000000800000 : "uImage2"
[    1.396307] 0x000000800000-0x000001000000 : "failsafe"
[    1.403196] 0x000001000000-0x000008000000 : "root"
[    1.411758] libphy: Fixed MDIO Bus: probed
[    1.418815] libphy: orion_mdio_bus: probed
[    1.424488] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    1.713400] ata1: SATA link down (SStatus 0 SControl F300)
[    2.112659] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:05:f5:25
[    2.121920] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.128416] ehci-pci: EHCI PCI platform driver
[    2.132923] ehci-platform: EHCI generic platform driver
[    2.138269] ehci-orion: EHCI orion driver
[    2.142509] orion-ehci f1050000.ehci: EHCI Host Controller
[    2.148001] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    2.155856] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
[    2.181894] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    2.188109] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08
[    2.196368] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.203580] usb usb1: Product: EHCI Host Controller
[    2.208434] usb usb1: Manufacturer: Linux 5.8.0-1-ARCH ehci_hcd
[    2.214346] usb usb1: SerialNumber: f1050000.ehci
[    2.219789] hub 1-0:1.0: USB hub found
[    2.223618] hub 1-0:1.0: 1 port detected
[    2.228144] ehci-atmel: EHCI Atmel driver
[    2.232281] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.238452] ohci-pci: OHCI PCI platform driver
[    2.242977] ohci-platform: OHCI generic platform driver
[    2.248301] ohci-atmel: OHCI Atmel driver
[    2.252690] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    2.257925] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[    2.266650] xhci_hcd 0000:01:00.0: hcc params 0x200073a1 hci version 0x100 quirks 0x0000000000080010
[    2.276316] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08
[    2.284579] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.291769] usb usb2: Product: xHCI Host Controller
[    2.296642] usb usb2: Manufacturer: Linux 5.8.0-1-ARCH xhci-hcd
[    2.302558] usb usb2: SerialNumber: 0000:01:00.0
[    2.307853] hub 2-0:1.0: USB hub found
[    2.311630] hub 2-0:1.0: 2 ports detected
[    2.316363] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    2.321583] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3
[    2.328992] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed
[    2.335793] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.344036] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.08
[    2.352290] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.359479] usb usb3: Product: xHCI Host Controller
[    2.364352] usb usb3: Manufacturer: Linux 5.8.0-1-ARCH xhci-hcd
[    2.370245] usb usb3: SerialNumber: 0000:01:00.0
[    2.375509] hub 3-0:1.0: USB hub found
[    2.379288] hub 3-0:1.0: 2 ports detected
[    2.384101] usbcore: registered new interface driver cdc_acm
[    2.389732] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    2.398005] usbcore: registered new interface driver uas
[    2.403524] usbcore: registered new interface driver usb-storage
[    2.409548] usbcore: registered new interface driver ums-alauda
[    2.415513] usbcore: registered new interface driver ums-cypress
[    2.421541] usbcore: registered new interface driver ums-datafab
[    2.427604] usbcore: registered new interface driver ums_eneub6250
[    2.433824] usbcore: registered new interface driver ums-freecom
[    2.439848] usbcore: registered new interface driver ums-isd200
[    2.445806] usbcore: registered new interface driver ums-jumpshot
[    2.451939] usbcore: registered new interface driver ums-karma
[    2.457793] usbcore: registered new interface driver ums-onetouch
[    2.463943] usbcore: registered new interface driver ums-realtek
[    2.469967] usbcore: registered new interface driver ums-sddr09
[    2.475926] usbcore: registered new interface driver ums-sddr55
[    2.481889] usbcore: registered new interface driver ums-usbat
[    2.487828] usbcore: registered new interface driver usbserial_generic
[    2.494392] usbserial: USB Serial support registered for generic
[    2.500418] usbcore: registered new interface driver ftdi_sio
[    2.506197] usbserial: USB Serial support registered for FTDI USB Serial Device
[    2.513846] usbcore: registered new interface driver pl2303
[    2.519427] usbserial: USB Serial support registered for pl2303
[    2.527563] mousedev: PS/2 mouse device common for all mice
[    3.601907] rtc-mv f1010300.rtc: internal RTC not ticking
[    3.607550] i2c /dev entries driver
[    3.611068] Driver for 1-wire Dallas network protocol.
[    3.618025] orion_wdt: Initial timeout 25 sec
[    3.623697] sdhci: Secure Digital Host Controller Interface driver
[    3.629848] sdhci: Copyright(c) Pierre Ossman
[    3.634686] mvsdio f1090000.mvsdio: Got CD GPIO
[    3.639232] mvsdio f1090000.mvsdio: Got WP GPIO
[    3.669594] sdhci-pltfm: SDHCI platform and OF driver helper
[    3.676239] ledtrig-cpu: registered to indicate activity on CPUs
[    3.684723] marvell-cesa f1030000.crypto: CESA device successfully registered
[    3.692270] hid: raw HID events driver (C) Jiri Kosina
[    3.697566] usbcore: registered new interface driver usbhid
[    3.703145] usbhid: USB HID core driver
[    3.710234] NET: Registered protocol family 10
[    3.718204] Segment Routing with IPv6
[    3.722033] NET: Registered protocol family 17
[    3.726705] Key type dns_resolver registered
[    3.731555] registered taskstats version 1
[    3.735713] Loading compiled-in X.509 certificates
[    3.740767] Key type ._fscrypt registered
[    3.744794] Key type .fscrypt registered
[    3.748700] Key type fscrypt-provisioning registered
[    3.756539] random: fast init done
[    3.761392] Key type encrypted registered
[    3.767998] printk: console [netcon0] enabled
[    3.772386] netconsole: network logging started
[    3.777591] input: gpio_keys as /devices/platform/gpio_keys/input/input0
[    3.785077] ALSA device list:
[    3.788039]   No soundcards found.
[    3.791729] Waiting 10 sec before mounting root device...
[    3.809161] mmc0: new high speed SDHC card at address 1234
[    3.815353] mmcblk0: mmc0:1234 SA04G 3.69 GiB (ro)
[    3.823621]  mmcblk0: p1
[   13.924642] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem
[   13.936613] EXT4-fs (mmcblk0p1): INFO: recovery required on readonly filesystem
[   13.943930] EXT4-fs (mmcblk0p1): write access unavailable, cannot proceed (try mounting with noload)
[   13.953169] VFS: Cannot open root device "mmcblk0p1" or unknown-block(179,1): error -30
[   13.961137] Please append a correct "root=" boot option; here are the available partitions:
[   13.969485] 0100            8192 ram0 
[   13.969489]  (driver?)
[   13.975581] 0101            8192 ram1 
[   13.975584]  (driver?)
[   13.981662] 0102            8192 ram2 
[   13.981665]  (driver?)
[   13.987763] 0103            8192 ram3 
[   13.987766]  (driver?)
[   13.993866] 1f00            2048 mtdblock0 
[   13.993870]  (driver?)
[   14.000376] 1f01            3072 mtdblock1 
[   14.000379]  (driver?)
[   14.006901] 1f02            3072 mtdblock2 
[   14.006904]  (driver?)
[   14.013433] 1f03            8192 mtdblock3 
[   14.013436]  (driver?)
[   14.019946] 1f04          114688 mtdblock4 
[   14.019949]  (driver?)
[   14.026479] b300         3864576 mmcblk0 
[   14.026483]  driver: mmcblk
[   14.033269]   b301         3863552 mmcblk0p1 07f2c1f7-01
[   14.033272] 
[   14.040042] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,1)
[   14.048442] CPU: 0 PID: 1 Comm: swapper Not tainted 5.8.0-1-ARCH #1
[   14.054673] Hardware name: Marvell Kirkwood (Flattened Device Tree)
[   14.060948] [<c00101ac>] (unwind_backtrace) from [<c000cef8>] (show_stack+0x10/0x14)
[   14.068671] [<c000cef8>] (show_stack) from [<c0025648>] (panic+0xe8/0x304)
[   14.075537] [<c0025648>] (panic) from [<c0d279b4>] (mount_block_root+0x1d4/0x278)
[   14.082992] [<c0d279b4>] (mount_block_root) from [<c0d27ca4>] (mount_root+0xf8/0x13c)
[   14.090791] [<c0d27ca4>] (mount_root) from [<c0d27e44>] (prepare_namespace+0x15c/0x1b4)
[   14.098772] [<c0d27e44>] (prepare_namespace) from [<c098e1dc>] (kernel_init+0x8/0xec)
[   14.106576] [<c098e1dc>] (kernel_init) from [<c0008560>] (ret_from_fork+0x14/0x34)
[   14.114110] Exception stack(0xc7841fb0 to 0xc7841ff8)
[   14.119142] 1fa0:                                     00000000 00000000 00000000 00000000
[   14.127284] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[   14.135429] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[   14.142021] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,1) ]---

Looks like its crashing here:

VFS: Cannot open root device "mmcblk0p1" or unknown-block(179,1): error -30
[   13.961137] Please append a correct "root=" boot option

Btw, my commands were as follows:

cd /media/rhodess/rootfs/boot
ls -l ./dtbs/*pogo*
cp -a zImage zImage.fdt
cat ./dtbs/kirkwood-pogoplug-series-4.dtb  >> zImage.fdt
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n ArchLinuxARM -d zImage.fdt  uImage
sync

Image Name:   ArchLinuxARM
Created:      Wed Jan 13 09:45:08 2021
Image Type:   ARM Linux Kernel Image (uncompressed)
Data Size:    4966300 Bytes = 4849.90 KiB = 4.74 MiB
Load Address: 00008000
Entry Point:  00008000

I will try redoing the card by logging in as root, after re-reading the output, it looks to me that it may be a write access issue



Edited 1 time(s). Last edit at 01/13/2021 02:10PM by Rhodess.

Rhodess,

> I will try redoing the card by logging in as root,
> after re-reading the output, it looks to me that
> it may be a write access issue

Right!

[   13.943930] EXT4-fs (mmcblk0p1): write access unavailable, cannot proceed (try mounting with noload)

Check the card switch, move it to write position.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

bodhi Wrote:
-------------------------------------------------------
> Rhodess,
>
>
> Mount the SD card rootfs on another Linux box like
> you did. Assuming it is mounted at
> /media/rhodess/rootfs.
>
>

> cd /media/rhodess/rootfs/boot
>

>
>
> Get the file name of this Pogolug V4 DTB file
>

> ls -l ./dtbs/*pogo*
>

> Assuming the file name is
> kirkwood-pogoplug_v4.dtb. If it was name
> differently in this Arch rootfs then use that name
> below
>
>

> cp -a zImage zImage.fdt
> cat ./dtbs/kirkwood-pogoplug_v4.dtb  >>
> zImage.fdt
> mkimage -A arm -O linux -T kernel -C none -a
> 0x00008000 -e 0x00008000 -n ArchLinuxARM -d
> zImage.fdt  uImage
> sync
>

>
> And umount the SD card. Bring it back to the Pogo
> V4 and start the box.
>
> ====
>
> Note that I don't know the kernel version in this
> rootfs so I name it ArchLinuxARM in the mkimage
> command above. To keep track of the correct
> version, you should regenerate the uImage again
> after you has booted successfully into Arch.

Quick question bodhi where you named ArchLinuxARM above, would that be "5.8.0-1-ARCH" based on my recent output?

I'm rebuilding so I thought I may as well have the correct name in the image.
e.g.

mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n 5.8.0-1-ARCH -d zImage.fdt  uImage

Thanks

Rhodess,

Yes, use this name so it can be referenced later: Linux-5.8.0-1-ARCH.

mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-5.8.0-1-ARCH -d zImage.fdt  uImage

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Well I thought I had it bodhi, It started to load up the kernel and then crashed. Once it hits this point it just hangs in a loop "40.219591] Exception stack(0xc7841d10 to 0xc7841d58)"

Here's my serial output:

U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45)
Pogoplug V4

SoC:   Kirkwood 88F6192_A1
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  128 MiB
MMC:   kwsdio: 0
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Hit any key to stop autoboot: 0 

MMC rescan: current device # 0 initialized OK
4966364 bytes read in 1337 ms (3.5 MiB/s)
** File not found /boot/uInitrd **
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-5.8.0-1-ARCH
   Created:      2021-01-14   5:11:20 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4966300 Bytes = 4.7 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
Using machid 0xf78 from environment

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.8.0-1-ARCH (builduser@leming) (armv5tel-unknown-linux-gnueabi-gcc (GCC) 9.3.0, GNU ld (GNU Binutils) 2.34) #1 Sun Aug 9 03:29:09 UTC 2020
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] OF: fdt: Machine model: Cloud Engines PogoPlug Series 4
[    0.000000] Memory policy: Data cache writeback
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p1 rootdelay=10 rootfstype=ext3 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 115388K/131072K available (9771K kernel code, 349K rwdata, 3404K rodata, 336K init, 197K bss, 15684K reserved, 0K cma-reserved)
[    0.000000] random: get_random_u32 called from cache_random_seq_create+0x80/0x134 with crng_init=0
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[    0.000013] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[    0.000061] Switching to timer-based delay loop, resolution 6ns
[    0.000400] Console: colour dummy device 80x30
[    0.000468] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666)
[    0.000499] pid_max: default: 32768 minimum: 301
[    0.001191] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.001224] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.003215] CPU: Testing write buffer coherency: ok
[    0.004612] Setting up static identity map for 0x8400 - 0x847c
[    0.005002] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[    0.005910] devtmpfs: initialized
[    0.011090] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.011129] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.011497] pinctrl core: initialized pinctrl subsystem
[    0.012570] thermal_sys: Registered thermal governor 'step_wise'
[    0.013626] NET: Registered protocol family 16
[    0.014491] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.015536] audit: initializing netlink subsys (disabled)
[    0.017216] cpuidle: using governor ladder
[    0.017240] cpuidle: using governor menu
[    0.017933] Feroceon L2: Enabling L2
[    0.017992] Feroceon L2: Cache support initialised.
[    0.030316] No ATAGs?
[    0.030852] Serial: AMBA PL011 UART driver
[    0.041062] audit: type=2000 audit(0.010:1): state=initialized audit_enabled=0 res=1
[    0.047896] AT91: Could not find identification node
[    0.048394] vgaarb: loaded
[    0.048979] SCSI subsystem initialized
[    0.049607] usbcore: registered new interface driver usbfs
[    0.049678] usbcore: registered new interface driver hub
[    0.049745] usbcore: registered new device driver usb
[    0.050247] pps_core: LinuxPPS API ver. 1 registered
[    0.050259] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.050291] PTP clock support registered
[    0.050639] Advanced Linux Sound Architecture Driver Initialized.
[    0.051863] clocksource: Switched to clocksource orion_clocksource
[    0.052277] VFS: Disk quotas dquot_6.6.0
[    0.052380] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.063960] NET: Registered protocol family 2
[    0.064907] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.064998] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.065028] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.065054] TCP: Hash tables configured (established 1024 bind 1024)
[    0.065556] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.065590] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.065882] NET: Registered protocol family 1
[    0.066490] RPC: Registered named UNIX socket transport module.
[    0.066503] RPC: Registered udp transport module.
[    0.066511] RPC: Registered tcp transport module.
[    0.066519] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.066534] PCI: CLS 0 bytes, default 32
[    0.069057] Initialise system trusted keyrings
[    0.069306] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[    0.080816] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.082426] NFS: Registering the id_resolver key type
[    0.082471] Key type id_resolver registered
[    0.082480] Key type id_legacy registered
[    0.082502] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.082549] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.083341] fuse: init (API version 7.31)
[    0.274192] Key type asymmetric registered
[    0.274211] Asymmetric key parser 'x509' registered
[    0.274280] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    0.274438] io scheduler mq-deadline registered
[    0.274451] io scheduler kyber registered
[    0.274837] io scheduler bfq registered
[    0.276585] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[    0.279114] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00
[    0.279140] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.279157] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[    0.279171] pci_bus 0000:00: root bus resource [io  0x1000-0xeffff]
[    0.279310] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400
[    0.279360] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[    0.280897] PCI: bus0: Fast back to back transfers disabled
[    0.280921] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.281118] pci 0000:01:00.0: [1b73:1009] type 00 class 0x0c0330
[    0.281170] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x0000ffff 64bit]
[    0.281197] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit]
[    0.281223] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit]
[    0.281326] pci 0000:01:00.0: supports D1
[    0.281341] pci 0000:01:00.0: PME# supported from D0 D1 D3hot
[    0.281388] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[    0.303166] PCI: bus1: Fast back to back transfers disabled
[    0.303193] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    0.303476] pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe00fffff]
[    0.303497] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0100000-0xe01007ff pref]
[    0.303521] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff 64bit]
[    0.303550] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0010000-0xe0010fff 64bit]
[    0.303577] pci 0000:01:00.0: BAR 4: assigned [mem 0xe0011000-0xe0011fff 64bit]
[    0.303602] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.303622] pci 0000:00:01.0:   bridge window [mem 0xe0000000-0xe00fffff]
[    0.303701] pci 0000:00:01.0: enabling device (0140 -> 0142)
[    0.303731] pci 0000:01:00.0: enabling device (0140 -> 0142)
[    0.304583] mv_xor f1060800.xor: Marvell shared XOR driver
[    0.363011] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    0.363415] mv_xor f1060900.xor: Marvell shared XOR driver
[    0.422987] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    0.423622] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.425245] printk: console [ttyS0] disabled
[    0.425391] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 10416666) is a 16550A
[    1.174120] printk: console [ttyS0] enabled
[    1.183571] brd: module loaded
[    1.197566] loop: module loaded
[    1.202005] sata_mv f1080000.sata: slots 32 ports 1
[    1.208797] scsi host0: sata_mv
[    1.212432] ata1: SATA max UDMA/133 irq 32
[    1.217763] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[    1.224139] nand: Hynix H27U1G8F2BTR-BC
[    1.227966] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.235538] Scanning device for bad blocks
[    1.354428] 5 cmdlinepart partitions found on MTD device orion_nand
[    1.360663] Creating 5 MTD partitions on "orion_nand":
[    1.365803] 0x000000000000-0x000000200000 : "u-boot"
[    1.372950] 0x000000200000-0x000000500000 : "uImage"
[    1.379576] 0x000000500000-0x000000800000 : "uImage2"
[    1.386321] 0x000000800000-0x000001000000 : "failsafe"
[    1.393210] 0x000001000000-0x000008000000 : "root"
[    1.401772] libphy: Fixed MDIO Bus: probed
[    1.408837] libphy: orion_mdio_bus: probed
[    1.414508] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    1.703407] ata1: SATA link down (SStatus 0 SControl F300)
[    2.102680] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:05:f5:25
[    2.111937] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.118435] ehci-pci: EHCI PCI platform driver
[    2.122941] ehci-platform: EHCI generic platform driver
[    2.128287] ehci-orion: EHCI orion driver
[    2.132530] orion-ehci f1050000.ehci: EHCI Host Controller
[    2.138028] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    2.145885] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
[    2.171905] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    2.178117] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08
[    2.186379] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.193589] usb usb1: Product: EHCI Host Controller
[    2.198445] usb usb1: Manufacturer: Linux 5.8.0-1-ARCH ehci_hcd
[    2.204355] usb usb1: SerialNumber: f1050000.ehci
[    2.209797] hub 1-0:1.0: USB hub found
[    2.213630] hub 1-0:1.0: 1 port detected
[    2.218157] ehci-atmel: EHCI Atmel driver
[    2.222291] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.228463] ohci-pci: OHCI PCI platform driver
[    2.232986] ohci-platform: OHCI generic platform driver
[    2.238311] ohci-atmel: OHCI Atmel driver
[    2.242695] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    2.247925] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[    2.256651] xhci_hcd 0000:01:00.0: hcc params 0x200073a1 hci version 0x100 quirks 0x0000000000080010
[    2.266326] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08
[    2.274589] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.281777] usb usb2: Product: xHCI Host Controller
[    2.286654] usb usb2: Manufacturer: Linux 5.8.0-1-ARCH xhci-hcd
[    2.292569] usb usb2: SerialNumber: 0000:01:00.0
[    2.297859] hub 2-0:1.0: USB hub found
[    2.301642] hub 2-0:1.0: 2 ports detected
[    2.306373] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    2.311592] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3
[    2.319003] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed
[    2.325819] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.334062] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.08
[    2.342318] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.349506] usb usb3: Product: xHCI Host Controller
[    2.354381] usb usb3: Manufacturer: Linux 5.8.0-1-ARCH xhci-hcd
[    2.360271] usb usb3: SerialNumber: 0000:01:00.0
[    2.365539] hub 3-0:1.0: USB hub found
[    2.369314] hub 3-0:1.0: 2 ports detected
[    2.374126] usbcore: registered new interface driver cdc_acm
[    2.379759] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    2.388031] usbcore: registered new interface driver uas
[    2.393537] usbcore: registered new interface driver usb-storage
[    2.399567] usbcore: registered new interface driver ums-alauda
[    2.405532] usbcore: registered new interface driver ums-cypress
[    2.411561] usbcore: registered new interface driver ums-datafab
[    2.417633] usbcore: registered new interface driver ums_eneub6250
[    2.423851] usbcore: registered new interface driver ums-freecom
[    2.429875] usbcore: registered new interface driver ums-isd200
[    2.435834] usbcore: registered new interface driver ums-jumpshot
[    2.441966] usbcore: registered new interface driver ums-karma
[    2.447818] usbcore: registered new interface driver ums-onetouch
[    2.453970] usbcore: registered new interface driver ums-realtek
[    2.459995] usbcore: registered new interface driver ums-sddr09
[    2.465956] usbcore: registered new interface driver ums-sddr55
[    2.471915] usbcore: registered new interface driver ums-usbat
[    2.477855] usbcore: registered new interface driver usbserial_generic
[    2.484420] usbserial: USB Serial support registered for generic
[    2.490448] usbcore: registered new interface driver ftdi_sio
[    2.496226] usbserial: USB Serial support registered for FTDI USB Serial Device
[    2.503863] usbcore: registered new interface driver pl2303
[    2.509444] usbserial: USB Serial support registered for pl2303
[    2.517594] mousedev: PS/2 mouse device common for all mice
[    3.601917] rtc-mv f1010300.rtc: internal RTC not ticking
[    3.607566] i2c /dev entries driver
[    3.611086] Driver for 1-wire Dallas network protocol.
[    3.618052] orion_wdt: Initial timeout 25 sec
[    3.623719] sdhci: Secure Digital Host Controller Interface driver
[    3.629873] sdhci: Copyright(c) Pierre Ossman
[    3.634708] mvsdio f1090000.mvsdio: Got CD GPIO
[    3.639256] mvsdio f1090000.mvsdio: Got WP GPIO
[    3.669622] sdhci-pltfm: SDHCI platform and OF driver helper
[    3.676259] ledtrig-cpu: registered to indicate activity on CPUs
[    3.684734] marvell-cesa f1030000.crypto: CESA device successfully registered
[    3.692278] hid: raw HID events driver (C) Jiri Kosina
[    3.697574] usbcore: registered new interface driver usbhid
[    3.703153] usbhid: USB HID core driver
[    3.710240] NET: Registered protocol family 10
[    3.718253] Segment Routing with IPv6
[    3.722062] NET: Registered protocol family 17
[    3.726736] Key type dns_resolver registered
[    3.731585] registered taskstats version 1
[    3.735737] Loading compiled-in X.509 certificates
[    3.740792] Key type ._fscrypt registered
[    3.744817] Key type .fscrypt registered
[    3.748724] Key type fscrypt-provisioning registered
[    3.757843] random: fast init done
[    3.761493] Key type encrypted registered
[    3.768100] printk: console [netcon0] enabled
[    3.772485] netconsole: network logging started
[    3.777687] input: gpio_keys as /devices/platform/gpio_keys/input/input0
[    3.785175] ALSA device list:
[    3.788131]   No soundcards found.
[    3.791818] Waiting 10 sec before mounting root device...
[    3.809307] mmc0: new high speed SDHC card at address e2cf
[    3.815496] mmcblk0: mmc0:e2cf SU08G 7.40 GiB 
[    3.822391]  mmcblk0: p1
[   13.922893] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem
[   13.967175] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
[   13.975348] VFS: Mounted root (ext3 filesystem) readonly on device 179:1.
[   14.003441] devtmpfs: mounted
[   14.007835] Freeing unused kernel memory: 336K
[   14.012287] Kernel memory protection not selected by kernel config.
[   14.018539] Run /sbin/init as init process
[   40.001871] watchdog: BUG: soft lockup - CPU#0 stuck for 23s! [init:1]
[   40.008378] Modules linked in:
[   40.011426] CPU: 0 PID: 1 Comm: init Not tainted 5.8.0-1-ARCH #1
[   40.017405] Hardware name: Marvell Kirkwood (Flattened Device Tree)
[   40.023669] PC is at handle_mm_fault+0x2c/0xbac
[   40.028184] LR is at do_page_fault+0x114/0x350
[   40.032604] pc : [<c01300a4>]    lr : [<c0010ba8>]    psr: 20000013
[   40.038842] sp : c7841d60  ip : 00000000  fp : 00000215
[   40.044043] r10: 00000800  r9 : c6c108fc  r8 : c6c108c0
[   40.049246] r7 : c7839d60  r6 : 00000215  r5 : 006592b8  r4 : c6c11d20
[   40.055743] r3 : c7839d60  r2 : c0d7d248  r1 : 00659000  r0 : c6c11d20
[   40.062243] Flags: nzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
[   40.069342] Control: 0005397f  Table: 06c14000  DAC: 00000051
[   40.075063] CPU: 0 PID: 1 Comm: init Not tainted 5.8.0-1-ARCH #1
[   40.081038] Hardware name: Marvell Kirkwood (Flattened Device Tree)
[   40.087306] [<c00101ac>] (unwind_backtrace) from [<c000cef8>] (show_stack+0x10/0x14)
[   40.095023] [<c000cef8>] (show_stack) from [<c00aa478>] (watchdog_timer_fn+0x190/0x1e4)
[   40.103010] [<c00aa478>] (watchdog_timer_fn) from [<c0071c68>] (__hrtimer_run_queues.constprop.0+0x120/0x1b8)
[   40.112893] [<c0071c68>] (__hrtimer_run_queues.constprop.0) from [<c00726c8>] (hrtimer_interrupt+0x104/0x28c)
[   40.122788] [<c00726c8>] (hrtimer_interrupt) from [<c07786bc>] (orion_clkevt_irq_handler+0x10/0x1c)
[   40.131811] [<c07786bc>] (orion_clkevt_irq_handler) from [<c0063dac>] (__handle_irq_event_percpu+0x3c/0x140)
[   40.141599] [<c0063dac>] (__handle_irq_event_percpu) from [<c0063edc>] (handle_irq_event_percpu+0x2c/0x88)
[   40.151215] [<c0063edc>] (handle_irq_event_percpu) from [<c0063f60>] (handle_irq_event+0x28/0x3c)
[   40.160057] [<c0063f60>] (handle_irq_event) from [<c0067a08>] (handle_edge_irq+0x90/0x1c8)
[   40.168287] [<c0067a08>] (handle_edge_irq) from [<c00631dc>] (generic_handle_irq+0x30/0x44)
[   40.176614] [<c00631dc>] (generic_handle_irq) from [<c0485a9c>] (orion_bridge_irq_handler+0x4c/0x58)
[   40.185715] [<c0485a9c>] (orion_bridge_irq_handler) from [<c00631dc>] (generic_handle_irq+0x30/0x44)
[   40.194811] [<c00631dc>] (generic_handle_irq) from [<c00637a4>] (__handle_domain_irq+0x48/0xa4)
[   40.203478] [<c00637a4>] (__handle_domain_irq) from [<c0485a2c>] (orion_handle_irq+0x68/0x8c)
[   40.211971] [<c0485a2c>] (orion_handle_irq) from [<c0008f28>] (__irq_svc+0x68/0x84)
[   40.219591] Exception stack(0xc7841d10 to 0xc7841d58)
[   40.224625] 1d00:                                     c6c11d20 00659000 c0d7d248 c7839d60
[   40.232767] 1d20: c6c11d20 006592b8 00000215 c7839d60 c6c108c0 c6c108fc 00000800 00000215
[   40.240912] 1d40: 00000000 c7841d60 c0010ba8 c01300a4 20000013 ffffffff
[   40.247502] [<c0008f28>] (__irq_svc) from [<c01300a4>] (handle_mm_fault+0x2c/0xbac)
[   40.255130] [<c01300a4>] (handle_mm_fault) from [<c0010ba8>] (do_page_fault+0x114/0x350)
[   40.263188] [<c0010ba8>] (do_page_fault) from [<c0010f54>] (do_DataAbort+0x38/0xc0)
[   40.270817] [<c0010f54>] (do_DataAbort) from [<c0008e8c>] (__dabt_svc+0x6c/0xa0)
[   40.278178] Exception stack(0xc7841e30 to 0xc7841e78)
[   40.283211] 1e20:                                     00000000 60000013 00000055 00000055
[   40.291354] 1e40: 00000000 c7840000 006592b8 00000d48 c732d840 004f1000 006592b8 c7158d00
[   40.299500] 1e60: 00000003 c7841e80 c0409e8c c0409ea0 80000013 ffffffff
[   40.306090] [<c0008e8c>] (__dabt_svc) from [<c0409ea0>] (__clear_user_memset+0xb0/0x168)
[   40.314150] [<c0409ea0>] (__clear_user_memset) from [<c01d4a48>] (load_elf_binary+0xe88/0x13cc)
[   40.322818] [<c01d4a48>] (load_elf_binary) from [<c01710bc>] (__do_execve_file+0x5a4/0x93c)
[   40.331134] [<c01710bc>] (__do_execve_file) from [<c01714fc>] (do_execve+0x2c/0x34)
[   40.338762] [<c01714fc>] (do_execve) from [<c0009c2c>] (try_to_run_init_process+0xc/0x38)
[   40.346916] [<c0009c2c>] (try_to_run_init_process) from [<c098e250>] (kernel_init+0x7c/0xec)
[   40.355317] [<c098e250>] (kernel_init) from [<c0008560>] (ret_from_fork+0x14/0x34)
[   40.362851] Exception stack(0xc7841fb0 to 0xc7841ff8)
[   40.367883] 1fa0:                                     00000000 00000000 00000000 00000000
[   40.376026] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[   40.384170] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[   68.001862] watchdog: BUG: soft lockup - CPU#0 stuck for 23s! [init:1]
[   68.008360] Modules linked in:
[   68.011409] CPU: 0 PID: 1 Comm: init Tainted: G             L    5.8.0-1-ARCH #1
[   68.018764] Hardware name: Marvell Kirkwood (Flattened Device Tree)
[   68.025007] PC is at do_page_fault+0x4c/0x350
[   68.029342] LR is at do_DataAbort+0x38/0xc0
[   68.033505] pc : [<c0010ae0>]    lr : [<c0010f54>]    psr: 40000013
[   68.039743] sp : c7841dc0  ip : 80000013  fp : c7158d00
[   68.044943] r10: 006592b8  r9 : c7840000  r8 : c6c108c0
[   68.050146] r7 : c7839d60  r6 : 00000805  r5 : 006592b8  r4 : c7841e30
[   68.056643] r3 : ffffe000  r2 : c7841dc0  r1 : 00000805  r0 : 006592b8
[   68.063140] Flags: nZcv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
[   68.070244] Control: 0005397f  Table: 06c14000  DAC: 00000051
[   68.075964] CPU: 0 PID: 1 Comm: init Tainted: G             L    5.8.0-1-ARCH #1
[   68.083321] Hardware name: Marvell Kirkwood (Flattened Device Tree)
[   68.089567] [<c00101ac>] (unwind_backtrace) from [<c000cef8>] (show_stack+0x10/0x14)
[   68.097287] [<c000cef8>] (show_stack) from [<c00aa478>] (watchdog_timer_fn+0x190/0x1e4)
[   68.105265] [<c00aa478>] (watchdog_timer_fn) from [<c0071c68>] (__hrtimer_run_queues.constprop.0+0x120/0x1b8)
[   68.115140] [<c0071c68>] (__hrtimer_run_queues.constprop.0) from [<c00726c8>] (hrtimer_interrupt+0x104/0x28c)
[   68.125020] [<c00726c8>] (hrtimer_interrupt) from [<c07786bc>] (orion_clkevt_irq_handler+0x10/0x1c)
[   68.134035] [<c07786bc>] (orion_clkevt_irq_handler) from [<c0063dac>] (__handle_irq_event_percpu+0x3c/0x140)
[   68.143822] [<c0063dac>] (__handle_irq_event_percpu) from [<c0063edc>] (handle_irq_event_percpu+0x2c/0x88)
[   68.153437] [<c0063edc>] (handle_irq_event_percpu) from [<c0063f60>] (handle_irq_event+0x28/0x3c)
[   68.162277] [<c0063f60>] (handle_irq_event) from [<c0067a08>] (handle_edge_irq+0x90/0x1c8)
[   68.170509] [<c0067a08>] (handle_edge_irq) from [<c00631dc>] (generic_handle_irq+0x30/0x44)
[   68.178832] [<c00631dc>] (generic_handle_irq) from [<c0485a9c>] (orion_bridge_irq_handler+0x4c/0x58)
[   68.187928] [<c0485a9c>] (orion_bridge_irq_handler) from [<c00631dc>] (generic_handle_irq+0x30/0x44)
[   68.197026] [<c00631dc>] (generic_handle_irq) from [<c00637a4>] (__handle_domain_irq+0x48/0xa4)
[   68.205692] [<c00637a4>] (__handle_domain_irq) from [<c0485a2c>] (orion_handle_irq+0x68/0x8c)
[   68.214184] [<c0485a2c>] (orion_handle_irq) from [<c0008f28>] (__irq_svc+0x68/0x84)
[   68.221805] Exception stack(0xc7841d70 to 0xc7841db8)
[   68.226838] 1d60:                                     006592b8 00000805 c7841dc0 ffffe000
[   68.234981] 1d80: c7841e30 006592b8 00000805 c7839d60 c6c108c0 c7840000 006592b8 c7158d00
[   68.243126] 1da0: 80000013 c7841dc0 c0010f54 c0010ae0 40000013 ffffffff
[   68.249712] [<c0008f28>] (__irq_svc) from [<c0010ae0>] (do_page_fault+0x4c/0x350)
[   68.257167] [<c0010ae0>] (do_page_fault) from [<c0010f54>] (do_DataAbort+0x38/0xc0)
[   68.264796] [<c0010f54>] (do_DataAbort) from [<c0008e8c>] (__dabt_svc+0x6c/0xa0)
[   68.272159] Exception stack(0xc7841e30 to 0xc7841e78)
[   68.277192] 1e20:                                     00000000 60000013 00000055 00000055
[   68.285335] 1e40: 00000000 c7840000 006592b8 00000d48 c732d840 004f1000 006592b8 c7158d00
[   68.293479] 1e60: 00000003 c7841e80 c0409e8c c0409ea0 80000013 ffffffff
[   68.300067] [<c0008e8c>] (__dabt_svc) from [<c0409ea0>] (__clear_user_memset+0xb0/0x168)
[   68.308128] [<c0409ea0>] (__clear_user_memset) from [<c01d4a48>] (load_elf_binary+0xe88/0x13cc)
[   68.316794] [<c01d4a48>] (load_elf_binary) from [<c01710bc>] (__do_execve_file+0x5a4/0x93c)
[   68.325114] [<c01710bc>] (__do_execve_file) from [<c01714fc>] (do_execve+0x2c/0x34)
[   68.332743] [<c01714fc>] (do_execve) from [<c0009c2c>] (try_to_run_init_process+0xc/0x38)
[   68.340892] [<c0009c2c>] (try_to_run_init_process) from [<c098e250>] (kernel_init+0x7c/0xec)
[   68.349296] [<c098e250>] (kernel_init) from [<c0008560>] (ret_from_fork+0x14/0x34)
[   68.356831] Exception stack(0xc7841fb0 to 0xc7841ff8)
[   68.361863] 1fa0:                                     00000000 00000000 00000000 00000000
[   68.370005] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[   68.378150] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[   96.001860] watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [init:1]
[   96.008354] Modules linked in:
[   96.011401] CPU: 0 PID: 1 Comm: init Tainted: G             L    5.8.0-1-ARCH #1
[   96.018758] Hardware name: Marvell Kirkwood (Flattened Device Tree)
[   96.025000] PC is at do_page_fault+0x4c/0x350
[   96.029335] LR is at do_DataAbort+0x38/0xc0
[   96.033499] pc : [<c0010ae0>]    lr : [<c0010f54>]    psr: 40000013
[   96.039736] sp : c7841dc0  ip : 80000013  fp : c7158d00
[   96.044937] r10: 006592b8  r9 : c7840000  r8 : c6c108c0
[   96.050139] r7 : c7839d60  r6 : 00000805  r5 : 006592b8  r4 : c7841e30
[   96.056637] r3 : ffffe000  r2 : c7841dc0  r1 : 00000805  r0 : 006592b8
[   96.063135] Flags: nZcv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
[   96.070237] Control: 0005397f  Table: 06c14000  DAC: 00000051
[   96.075958] CPU: 0 PID: 1 Comm: init Tainted: G             L    5.8.0-1-ARCH #1
[   96.083315] Hardware name: Marvell Kirkwood (Flattened Device Tree)
[   96.089567] [<c00101ac>] (unwind_backtrace) from [<c000cef8>] (show_stack+0x10/0x14)
[   96.097280] [<c000cef8>] (show_stack) from [<c00aa478>] (watchdog_timer_fn+0x190/0x1e4)
[   96.105259] [<c00aa478>] (watchdog_timer_fn) from [<c0071c68>] (__hrtimer_run_queues.constprop.0+0x120/0x1b8)
[   96.115133] [<c0071c68>] (__hrtimer_run_queues.constprop.0) from [<c00726c8>] (hrtimer_interrupt+0x104/0x28c)
[   96.125011] [<c00726c8>] (hrtimer_interrupt) from [<c07786bc>] (orion_clkevt_irq_handler+0x10/0x1c)
[   96.134030] [<c07786bc>] (orion_clkevt_irq_handler) from [<c0063dac>] (__handle_irq_event_percpu+0x3c/0x140)
[   96.143816] [<c0063dac>] (__handle_irq_event_percpu) from [<c0063edc>] (handle_irq_event_percpu+0x2c/0x88)
[   96.153431] [<c0063edc>] (handle_irq_event_percpu) from [<c0063f60>] (handle_irq_event+0x28/0x3c)
[   96.162271] [<c0063f60>] (handle_irq_event) from [<c0067a08>] (handle_edge_irq+0x90/0x1c8)
[   96.170503] [<c0067a08>] (handle_edge_irq) from [<c00631dc>] (generic_handle_irq+0x30/0x44)
[   96.178826] [<c00631dc>] (generic_handle_irq) from [<c0485a9c>] (orion_bridge_irq_handler+0x4c/0x58)
[   96.187923] [<c0485a9c>] (orion_bridge_irq_handler) from [<c00631dc>] (generic_handle_irq+0x30/0x44)
[   96.197020] [<c00631dc>] (generic_handle_irq) from [<c00637a4>] (__handle_domain_irq+0x48/0xa4)
[   96.205685] [<c00637a4>] (__handle_domain_irq) from [<c0485a2c>] (orion_handle_irq+0x68/0x8c)
[   96.214178] [<c0485a2c>] (orion_handle_irq) from [<c0008f28>] (__irq_svc+0x68/0x84)
[   96.221799] Exception stack(0xc7841d70 to 0xc7841db8)
[   96.226831] 1d60:                                     006592b8 00000805 c7841dc0 ffffe000
[   96.234974] 1d80: c7841e30 006592b8 00000805 c7839d60 c6c108c0 c7840000 006592b8 c7158d00
[   96.243119] 1da0: 80000013 c7841dc0 c0010f54 c0010ae0 40000013 ffffffff
[   96.249705] [<c0008f28>] (__irq_svc) from [<c0010ae0>] (do_page_fault+0x4c/0x350)
[   96.257161] [<c0010ae0>] (do_page_fault) from [<c0010f54>] (do_DataAbort+0x38/0xc0)
[   96.264790] [<c0010f54>] (do_DataAbort) from [<c0008e8c>] (__dabt_svc+0x6c/0xa0)
[   96.272153] Exception stack(0xc7841e30 to 0xc7841e78)
[   96.277185] 1e20:                                     00000000 60000013 00000055 00000055
[   96.285328] 1e40: 00000000 c7840000 006592b8 00000d48 c732d840 004f1000 006592b8 c7158d00
[   96.293473] 1e60: 00000003 c7841e80 c0409e8c c0409ea0 80000013 ffffffff
[   96.300061] [<c0008e8c>] (__dabt_svc) from [<c0409ea0>] (__clear_user_memset+0xb0/0x168)
[   96.308121] [<c0409ea0>] (__clear_user_memset) from [<c01d4a48>] (load_elf_binary+0xe88/0x13cc)
[   96.316788] [<c01d4a48>] (load_elf_binary) from [<c01710bc>] (__do_execve_file+0x5a4/0x93c)
[   96.325107] [<c01710bc>] (__do_execve_file) from [<c01714fc>] (do_execve+0x2c/0x34)
[   96.332736] [<c01714fc>] (do_execve) from [<c0009c2c>] (try_to_run_init_process+0xc/0x38)
[   96.340885] [<c0009c2c>] (try_to_run_init_process) from [<c098e250>] (kernel_init+0x7c/0xec)
[   96.349289] [<c098e250>] (kernel_init) from [<c0008560>] (ret_from_fork+0x14/0x34)
[   96.356825] Exception stack(0xc7841fb0 to 0xc7841ff8)
[   96.361857] 1fa0:                                     00000000 00000000 00000000 00000000
[   96.369999] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[   96.378144] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[  124.001861] watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [init:1]
[  124.008355] Modules linked in:
[  124.011404] CPU: 0 PID: 1 Comm: init Tainted: G             L    5.8.0-1-ARCH #1
[  124.018759] Hardware name: Marvell Kirkwood (Flattened Device Tree)
[  124.024995] PC is at do_page_fault+0x4c/0x350
[  124.029329] LR is at do_DataAbort+0x38/0xc0
[  124.033491] pc : [<c0010ae0>]    lr : [<c0010f54>]    psr: 40000013
[  124.039730] sp : c7841dc0  ip : 80000013  fp : c7158d00
[  124.044931] r10: 006592b8  r9 : c7840000  r8 : c6c108c0
[  124.050134] r7 : c7839d60  r6 : 00000805  r5 : 006592b8  r4 : c7841e30
[  124.056630] r3 : ffffe000  r2 : c7841dc0  r1 : 00000805  r0 : 006592b8
[  124.063129] Flags: nZcv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
[  124.070230] Control: 0005397f  Table: 06c14000  DAC: 00000051
[  124.075952] CPU: 0 PID: 1 Comm: init Tainted: G             L    5.8.0-1-ARCH #1
[  124.083309] Hardware name: Marvell Kirkwood (Flattened Device Tree)
[  124.089561] [<c00101ac>] (unwind_backtrace) from [<c000cef8>] (show_stack+0x10/0x14)
[  124.097274] [<c000cef8>] (show_stack) from [<c00aa478>] (watchdog_timer_fn+0x190/0x1e4)
[  124.105253] [<c00aa478>] (watchdog_timer_fn) from [<c0071c68>] (__hrtimer_run_queues.constprop.0+0x120/0x1b8)
[  124.115127] [<c0071c68>] (__hrtimer_run_queues.constprop.0) from [<c00726c8>] (hrtimer_interrupt+0x104/0x28c)
[  124.125006] [<c00726c8>] (hrtimer_interrupt) from [<c07786bc>] (orion_clkevt_irq_handler+0x10/0x1c)
[  124.134022] [<c07786bc>] (orion_clkevt_irq_handler) from [<c0063dac>] (__handle_irq_event_percpu+0x3c/0x140)
[  124.143809] [<c0063dac>] (__handle_irq_event_percpu) from [<c0063edc>] (handle_irq_event_percpu+0x2c/0x88)
[  124.153424] [<c0063edc>] (handle_irq_event_percpu) from [<c0063f60>] (handle_irq_event+0x28/0x3c)
[  124.162264] [<c0063f60>] (handle_irq_event) from [<c0067a08>] (handle_edge_irq+0x90/0x1c8)
[  124.170496] [<c0067a08>] (handle_edge_irq) from [<c00631dc>] (generic_handle_irq+0x30/0x44)
[  124.178818] [<c00631dc>] (generic_handle_irq) from [<c0485a9c>] (orion_bridge_irq_handler+0x4c/0x58)
[  124.187916] [<c0485a9c>] (orion_bridge_irq_handler) from [<c00631dc>] (generic_handle_irq+0x30/0x44)
[  124.197012] [<c00631dc>] (generic_handle_irq) from [<c00637a4>] (__handle_domain_irq+0x48/0xa4)
[  124.205679] [<c00637a4>] (__handle_domain_irq) from [<c0485a2c>] (orion_handle_irq+0x68/0x8c)
[  124.214171] [<c0485a2c>] (orion_handle_irq) from [<c0008f28>] (__irq_svc+0x68/0x84)
[  124.221792] Exception stack(0xc7841d70 to 0xc7841db8)
[  124.226826] 1d60:                                     006592b8 00000805 c7841dc0 ffffe000
[  124.234969] 1d80: c7841e30 006592b8 00000805 c7839d60 c6c108c0 c7840000 006592b8 c7158d00
[  124.243113] 1da0: 80000013 c7841dc0 c0010f54 c0010ae0 40000013 ffffffff
[  124.249699] [<c0008f28>] (__irq_svc) from [<c0010ae0>] (do_page_fault+0x4c/0x350)
[  124.257155] [<c0010ae0>] (do_page_fault) from [<c0010f54>] (do_DataAbort+0x38/0xc0)
[  124.264782] [<c0010f54>] (do_DataAbort) from [<c0008e8c>] (__dabt_svc+0x6c/0xa0)
[  124.272137] Exception stack(0xc7841e30 to 0xc7841e78)
[  124.277169] 1e20:                                     00000000 60000013 00000055 00000055
[  124.285313] 1e40: 00000000 c7840000 006592b8 00000d48 c732d840 004f1000 006592b8 c7158d00
[  124.293458] 1e60: 00000003 c7841e80 c0409e8c c0409ea0 80000013 ffffffff
[  124.300045] [<c0008e8c>] (__dabt_svc) from [<c0409ea0>] (__clear_user_memset+0xb0/0x168)
[  124.308106] [<c0409ea0>] (__clear_user_memset) from [<c01d4a48>] (load_elf_binary+0xe88/0x13cc)
[  124.316773] [<c01d4a48>] (load_elf_binary) from [<c01710bc>] (__do_execve_file+0x5a4/0x93c)
[  124.325091] [<c01710bc>] (__do_execve_file) from [<c01714fc>] (do_execve+0x2c/0x34)
[  124.332722] [<c01714fc>] (do_execve) from [<c0009c2c>] (try_to_run_init_process+0xc/0x38)
[  124.340871] [<c0009c2c>] (try_to_run_init_process) from [<c098e250>] (kernel_init+0x7c/0xec)
[  124.349275] [<c098e250>] (kernel_init) from [<c0008560>] (ret_from_fork+0x14/0x34)
[  124.356809] Exception stack(0xc7841fb0 to 0xc7841ff8)
[  124.361841] 1fa0:                                     00000000 00000000 00000000 00000000
[  124.369984] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[  124.378129] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[  137.621938] random: crng init done
[  164.001860] watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [init:1]
[  164.008349] Modules linked in:
[  164.011398] CPU: 0 PID: 1 Comm: init Tainted: G             L    5.8.0-1-ARCH #1
[  164.018754] Hardware name: Marvell Kirkwood (Flattened Device Tree)
[  164.025007] PC is at memset+0x28/0xdc
[  164.028655] LR is at handle_mm_fault+0xa8/0xbac
[  164.033167] pc : [<c046b848>]    lr : [<c0130120>]    psr: 20000013
[  164.039405] sp : c7841d48  ip : c7841d70  fp : 00000215
[  164.044606] r10: 00000800  r9 : c6c108fc  r8 : c6c108c0
[  164.049808] r7 : 00000000  r6 : 00000215  r5 : 00659000  r4 : 00000000
[  164.056306] r3 : 00000000  r2 : 0000002c  r1 : 00000000  r0 : c7841d70
[  164.062803] Flags: nzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
[  164.069905] Control: 0005397f  Table: 06c14000  DAC: 00000051
[  164.075627] CPU: 0 PID: 1 Comm: init Tainted: G             L    5.8.0-1-ARCH #1
[  164.082984] Hardware name: Marvell Kirkwood (Flattened Device Tree)
[  164.089235] [<c00101ac>] (unwind_backtrace) from [<c000cef8>] (show_stack+0x10/0x14)
[  164.096949] [<c000cef8>] (show_stack) from [<c00aa478>] (watchdog_timer_fn+0x190/0x1e4)
[  164.104927] [<c00aa478>] (watchdog_timer_fn) from [<c0071c68>] (__hrtimer_run_queues.constprop.0+0x120/0x1b8)
[  164.114801] [<c0071c68>] (__hrtimer_run_queues.constprop.0) from [<c00726c8>] (hrtimer_interrupt+0x104/0x28c)
[  164.124680] [<c00726c8>] (hrtimer_interrupt) from [<c07786bc>] (orion_clkevt_irq_handler+0x10/0x1c)
[  164.133697] [<c07786bc>] (orion_clkevt_irq_handler) from [<c0063dac>] (__handle_irq_event_percpu+0x3c/0x140)
[  164.143483] [<c0063dac>] (__handle_irq_event_percpu) from [<c0063edc>] (handle_irq_event_percpu+0x2c/0x88)
[  164.153100] [<c0063edc>] (handle_irq_event_percpu) from [<c0063f60>] (handle_irq_event+0x28/0x3c)
[  164.161939] [<c0063f60>] (handle_irq_event) from [<c0067a08>] (handle_edge_irq+0x90/0x1c8)
[  164.170172] [<c0067a08>] (handle_edge_irq) from [<c00631dc>] (generic_handle_irq+0x30/0x44)
[  164.178493] [<c00631dc>] (generic_handle_irq) from [<c0485a9c>] (orion_bridge_irq_handler+0x4c/0x58)
[  164.187591] [<c0485a9c>] (orion_bridge_irq_handler) from [<c00631dc>] (generic_handle_irq+0x30/0x44)
[  164.196687] [<c00631dc>] (generic_handle_irq) from [<c00637a4>] (__handle_domain_irq+0x48/0xa4)
[  164.205353] [<c00637a4>] (__handle_domain_irq) from [<c0485a2c>] (orion_handle_irq+0x68/0x8c)
[  164.213846] [<c0485a2c>] (orion_handle_irq) from [<c0008f28>] (__irq_svc+0x68/0x84)
[  164.221468] Exception stack(0xc7841cf8 to 0xc7841d40)
[  164.226497] 1ce0:                                                       c7841d70 00000000
[  164.234642] 1d00: 0000002c 00000000 00000000 00659000 00000215 00000000 c6c108c0 c6c108fc
[  164.242791] 1d20: 00000800 00000215 c7841d70 c7841d48 c0130120 c046b848 20000013 ffffffff
[  164.250941] [<c0008f28>] (__irq_svc) from [<c046b848>] (memset+0x28/0xdc)
[  164.257708] [<c046b848>] (memset) from [<c0130120>] (handle_mm_fault+0xa8/0xbac)
[  164.265075] [<c0130120>] (handle_mm_fault) from [<c0010ba8>] (do_page_fault+0x114/0x350)
[  164.273133] [<c0010ba8>] (do_page_fault) from [<c0010f54>] (do_DataAbort+0x38/0xc0)
[  164.280762] [<c0010f54>] (do_DataAbort) from [<c0008e8c>] (__dabt_svc+0x6c/0xa0)
[  164.288125] Exception stack(0xc7841e30 to 0xc7841e78)
[  164.293157] 1e20:                                     00000000 60000013 00000055 00000055
[  164.301301] 1e40: 00000000 c7840000 006592b8 00000d48 c732d840 004f1000 006592b8 c7158d00
[  164.309445] 1e60: 00000003 c7841e80 c0409e8c c0409ea0 80000013 ffffffff
[  164.316032] [<c0008e8c>] (__dabt_svc) from [<c0409ea0>] (__clear_user_memset+0xb0/0x168)
[  164.324093] [<c0409ea0>] (__clear_user_memset) from [<c01d4a48>] (load_elf_binary+0xe88/0x13cc)
[  164.332761] [<c01d4a48>] (load_elf_binary) from [<c01710bc>] (__do_execve_file+0x5a4/0x93c)
[  164.341079] [<c01710bc>] (__do_execve_file) from [<c01714fc>] (do_execve+0x2c/0x34)
[  164.348708] [<c01714fc>] (do_execve) from [<c0009c2c>] (try_to_run_init_process+0xc/0x38)
[  164.356858] [<c0009c2c>] (try_to_run_init_process) from [<c098e250>] (kernel_init+0x7c/0xec)
[  164.365262] [<c098e250>] (kernel_init) from [<c0008560>] (ret_from_fork+0x14/0x34)
[  164.372797] Exception stack(0xc7841fb0 to 0xc7841ff8)
[  164.377829] 1fa0:                                     00000000 00000000 00000000 00000000
[  164.385970] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[  164.394108] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000

Do you have any ideas?

Rhodess,

Since this is Arch rootfs, I can only make an educated guess: that this might have something to do with you SD card.

This should not happen:

[   13.975348] VFS: Mounted root (ext3 filesystem) readonly on device 179:1.

Are you using a SD adapter with microSD or full size SD card?

And try using USB rootfs to see if you will see the same problem.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Hi bodhi, I’m using an 8Gb SanDisk micro SD with adapter. I do have a Kingston 4Gb full size card though, so I can try that and also USB.

Thanks for the update

No luck bodhi, I used a SanDisk USB and a PNY 4GB full-size flash card, and I booted from both. I get a kernel panic in both cases but both look to be different issues. The flash card gives the VFS read error, but the USB gives the same error as the SanDisk flash card I used the other day
Here is the USB log:

U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45)
Pogoplug V4

SoC:   Kirkwood 88F6192_A1
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  128 MiB
MMC:   kwsdio: 0
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Hit any key to stop autoboot: 0 
Card did not respond to voltage select!
** Bad device mmc 0 **
** Bad device mmc 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
4966364 bytes read in 338 ms (14 MiB/s)
** File not found /boot/uInitrd **
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-5.8.0-1-ARCH
   Created:      2021-01-15   5:43:57 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4966300 Bytes = 4.7 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
Using machid 0xf78 from environment

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.8.0-1-ARCH (builduser@leming) (armv5tel-unknown-linux-gnueabi-gcc (GCC) 9.3.0, GNU ld (GNU Binutils) 2.34) #1 Sun Aug 9 03:29:09 UTC 2020
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] OF: fdt: Machine model: Cloud Engines PogoPlug Series 4
[    0.000000] Memory policy: Data cache writeback
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext3 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 115388K/131072K available (9771K kernel code, 349K rwdata, 3404K rodata, 336K init, 197K bss, 15684K reserved, 0K cma-reserved)
[    0.000000] random: get_random_u32 called from cache_random_seq_create+0x80/0x134 with crng_init=0
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[    0.000013] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[    0.000061] Switching to timer-based delay loop, resolution 6ns
[    0.000398] Console: colour dummy device 80x30
[    0.000469] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666)
[    0.000500] pid_max: default: 32768 minimum: 301
[    0.001195] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.001229] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.003209] CPU: Testing write buffer coherency: ok
[    0.004624] Setting up static identity map for 0x8400 - 0x847c
[    0.005013] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[    0.005918] devtmpfs: initialized
[    0.011084] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.011121] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.011487] pinctrl core: initialized pinctrl subsystem
[    0.012563] thermal_sys: Registered thermal governor 'step_wise'
[    0.013618] NET: Registered protocol family 16
[    0.014483] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.015538] audit: initializing netlink subsys (disabled)
[    0.017233] cpuidle: using governor ladder
[    0.017258] cpuidle: using governor menu
[    0.017947] Feroceon L2: Enabling L2
[    0.018006] Feroceon L2: Cache support initialised.
[    0.030330] No ATAGs?
[    0.030865] Serial: AMBA PL011 UART driver
[    0.041104] audit: type=2000 audit(0.010:1): state=initialized audit_enabled=0 res=1
[    0.047904] AT91: Could not find identification node
[    0.048405] vgaarb: loaded
[    0.048992] SCSI subsystem initialized
[    0.049617] usbcore: registered new interface driver usbfs
[    0.049688] usbcore: registered new interface driver hub
[    0.049754] usbcore: registered new device driver usb
[    0.050255] pps_core: LinuxPPS API ver. 1 registered
[    0.050267] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.050298] PTP clock support registered
[    0.050646] Advanced Linux Sound Architecture Driver Initialized.
[    0.051876] clocksource: Switched to clocksource orion_clocksource
[    0.052283] VFS: Disk quotas dquot_6.6.0
[    0.052384] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.063944] NET: Registered protocol family 2
[    0.064893] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.064986] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.065016] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.065042] TCP: Hash tables configured (established 1024 bind 1024)
[    0.065552] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.065586] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.065877] NET: Registered protocol family 1
[    0.066484] RPC: Registered named UNIX socket transport module.
[    0.066496] RPC: Registered udp transport module.
[    0.066504] RPC: Registered tcp transport module.
[    0.066511] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.066527] PCI: CLS 0 bytes, default 32
[    0.069059] Initialise system trusted keyrings
[    0.069301] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[    0.080823] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.082429] NFS: Registering the id_resolver key type
[    0.082472] Key type id_resolver registered
[    0.082481] Key type id_legacy registered
[    0.082503] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.082551] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.083338] fuse: init (API version 7.31)
[    0.277740] Key type asymmetric registered
[    0.277759] Asymmetric key parser 'x509' registered
[    0.277827] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    0.277983] io scheduler mq-deadline registered
[    0.277996] io scheduler kyber registered
[    0.278386] io scheduler bfq registered
[    0.280128] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[    0.282724] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00
[    0.282750] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.282767] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[    0.282781] pci_bus 0000:00: root bus resource [io  0x1000-0xeffff]
[    0.282916] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400
[    0.282965] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[    0.284502] PCI: bus0: Fast back to back transfers disabled
[    0.284525] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.284722] pci 0000:01:00.0: [1b73:1009] type 00 class 0x0c0330
[    0.284775] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x0000ffff 64bit]
[    0.284802] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit]
[    0.284828] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit]
[    0.284930] pci 0000:01:00.0: supports D1
[    0.284946] pci 0000:01:00.0: PME# supported from D0 D1 D3hot
[    0.284993] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[    0.313170] PCI: bus1: Fast back to back transfers disabled
[    0.313196] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    0.313479] pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe00fffff]
[    0.313500] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0100000-0xe01007ff pref]
[    0.313524] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff 64bit]
[    0.313552] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0010000-0xe0010fff 64bit]
[    0.313579] pci 0000:01:00.0: BAR 4: assigned [mem 0xe0011000-0xe0011fff 64bit]
[    0.313603] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.313623] pci 0000:00:01.0:   bridge window [mem 0xe0000000-0xe00fffff]
[    0.313703] pci 0000:00:01.0: enabling device (0140 -> 0142)
[    0.313734] pci 0000:01:00.0: enabling device (0140 -> 0142)
[    0.314579] mv_xor f1060800.xor: Marvell shared XOR driver
[    0.373027] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    0.373430] mv_xor f1060900.xor: Marvell shared XOR driver
[    0.432991] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    0.433632] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.435257] printk: console [ttyS0] disabled
[    0.435402] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 10416666) is a 16550A
[    1.183711] printk: console [ttyS0] enabled
[    1.193157] brd: module loaded
[    1.207120] loop: module loaded
[    1.211494] sata_mv f1080000.sata: slots 32 ports 1
[    1.218361] scsi host0: sata_mv
[    1.222004] ata1: SATA max UDMA/133 irq 32
[    1.227336] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[    1.233708] nand: Hynix H27U1G8F2BTR-BC
[    1.237531] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.245103] Scanning device for bad blocks
[    1.363991] 5 cmdlinepart partitions found on MTD device orion_nand
[    1.370230] Creating 5 MTD partitions on "orion_nand":
[    1.375371] 0x000000000000-0x000000200000 : "u-boot"
[    1.382487] 0x000000200000-0x000000500000 : "uImage"
[    1.389111] 0x000000500000-0x000000800000 : "uImage2"
[    1.395860] 0x000000800000-0x000001000000 : "failsafe"
[    1.402754] 0x000001000000-0x000008000000 : "root"
[    1.411322] libphy: Fixed MDIO Bus: probed
[    1.418399] libphy: orion_mdio_bus: probed
[    1.424113] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    1.713422] ata1: SATA link down (SStatus 0 SControl F300)
[    2.112704] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:05:f5:25
[    2.121966] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.128468] ehci-pci: EHCI PCI platform driver
[    2.132974] ehci-platform: EHCI generic platform driver
[    2.138321] ehci-orion: EHCI orion driver
[    2.142563] orion-ehci f1050000.ehci: EHCI Host Controller
[    2.148060] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    2.155921] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
[    2.181918] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    2.188133] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08
[    2.196394] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.203605] usb usb1: Product: EHCI Host Controller
[    2.208460] usb usb1: Manufacturer: Linux 5.8.0-1-ARCH ehci_hcd
[    2.214371] usb usb1: SerialNumber: f1050000.ehci
[    2.219806] hub 1-0:1.0: USB hub found
[    2.223636] hub 1-0:1.0: 1 port detected
[    2.228160] ehci-atmel: EHCI Atmel driver
[    2.232299] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.238478] ohci-pci: OHCI PCI platform driver
[    2.243004] ohci-platform: OHCI generic platform driver
[    2.248333] ohci-atmel: OHCI Atmel driver
[    2.252713] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    2.257949] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[    2.266677] xhci_hcd 0000:01:00.0: hcc params 0x200073a1 hci version 0x100 quirks 0x0000000000080010
[    2.276351] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08
[    2.284611] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.291803] usb usb2: Product: xHCI Host Controller
[    2.296676] usb usb2: Manufacturer: Linux 5.8.0-1-ARCH xhci-hcd
[    2.302592] usb usb2: SerialNumber: 0000:01:00.0
[    2.307886] hub 2-0:1.0: USB hub found
[    2.311664] hub 2-0:1.0: 2 ports detected
[    2.316398] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    2.321616] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3
[    2.329025] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed
[    2.335438] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.343675] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.08
[    2.351926] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.359116] usb usb3: Product: xHCI Host Controller
[    2.363990] usb usb3: Manufacturer: Linux 5.8.0-1-ARCH xhci-hcd
[    2.369881] usb usb3: SerialNumber: 0000:01:00.0
[    2.375133] hub 3-0:1.0: USB hub found
[    2.378914] hub 3-0:1.0: 2 ports detected
[    2.383728] usbcore: registered new interface driver cdc_acm
[    2.389360] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    2.397629] usbcore: registered new interface driver uas
[    2.403139] usbcore: registered new interface driver usb-storage
[    2.409167] usbcore: registered new interface driver ums-alauda
[    2.415132] usbcore: registered new interface driver ums-cypress
[    2.421160] usbcore: registered new interface driver ums-datafab
[    2.427226] usbcore: registered new interface driver ums_eneub6250
[    2.433452] usbcore: registered new interface driver ums-freecom
[    2.439475] usbcore: registered new interface driver ums-isd200
[    2.445437] usbcore: registered new interface driver ums-jumpshot
[    2.451543] usbcore: registered new interface driver ums-karma
[    2.457418] usbcore: registered new interface driver ums-onetouch
[    2.463570] usbcore: registered new interface driver ums-realtek
[    2.469595] usbcore: registered new interface driver ums-sddr09
[    2.475557] usbcore: registered new interface driver ums-sddr55
[    2.481490] usbcore: registered new interface driver ums-usbat
[    2.487455] usbcore: registered new interface driver usbserial_generic
[    2.494021] usbserial: USB Serial support registered for generic
[    2.500048] usbcore: registered new interface driver ftdi_sio
[    2.505826] usbserial: USB Serial support registered for FTDI USB Serial Device
[    2.513458] usbcore: registered new interface driver pl2303
[    2.519038] usbserial: USB Serial support registered for pl2303
[    2.527271] mousedev: PS/2 mouse device common for all mice
[    2.671914] usb 1-1: new high-speed USB device number 2 using orion-ehci
[    2.873171] usb 1-1: New USB device found, idVendor=0781, idProduct=5571, bcdDevice= 1.00
[    2.881335] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.888463] random: fast init done
[    2.891859] usb 1-1: Product: Cruzer Fit
[    2.895782] usb 1-1: Manufacturer: SanDisk
[    2.899868] usb 1-1: SerialNumber: 4C530302040606121535
[    2.906091] usb-storage 1-1:1.0: USB Mass Storage device detected
[    2.912685] scsi host1: usb-storage 1-1:1.0
[    3.601915] rtc-mv f1010300.rtc: internal RTC not ticking
[    3.607605] i2c /dev entries driver
[    3.611114] Driver for 1-wire Dallas network protocol.
[    3.618145] orion_wdt: Initial timeout 25 sec
[    3.623823] sdhci: Secure Digital Host Controller Interface driver
[    3.629977] sdhci: Copyright(c) Pierre Ossman
[    3.634834] mvsdio f1090000.mvsdio: Got CD GPIO
[    3.639376] mvsdio f1090000.mvsdio: Got WP GPIO
[    3.669749] sdhci-pltfm: SDHCI platform and OF driver helper
[    3.676391] ledtrig-cpu: registered to indicate activity on CPUs
[    3.684798] marvell-cesa f1030000.crypto: CESA device successfully registered
[    3.692346] hid: raw HID events driver (C) Jiri Kosina
[    3.697661] usbcore: registered new interface driver usbhid
[    3.703242] usbhid: USB HID core driver
[    3.710301] NET: Registered protocol family 10
[    3.718253] Segment Routing with IPv6
[    3.722073] NET: Registered protocol family 17
[    3.726741] Key type dns_resolver registered
[    3.731612] registered taskstats version 1
[    3.735766] Loading compiled-in X.509 certificates
[    3.740834] Key type ._fscrypt registered
[    3.744860] Key type .fscrypt registered
[    3.748760] Key type fscrypt-provisioning registered
[    3.758052] Key type encrypted registered
[    3.764582] printk: console [netcon0] enabled
[    3.768952] netconsole: network logging started
[    3.774168] input: gpio_keys as /devices/platform/gpio_keys/input/input0
[    3.781597] ALSA device list:
[    3.784603]   No soundcards found.
[    3.788294] Waiting 10 sec before mounting root device...
[    3.922928] scsi 1:0:0:0: Direct-Access     SanDisk  Cruzer Fit       1.00 PQ: 0 ANSI: 6
[    3.931992] sd 1:0:0:0: Attached scsi generic sg0 type 0
[    3.938119] sd 1:0:0:0: [sda] 15630336 512-byte logical blocks: (8.00 GB/7.45 GiB)
[    3.947074] sd 1:0:0:0: [sda] Write Protect is off
[    3.952570] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    3.967327]  sda: sda1
[    3.973227] sd 1:0:0:0: [sda] Attached SCSI removable disk
[   13.923611] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[   13.961465] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[   13.969202] VFS: Mounted root (ext3 filesystem) readonly on device 8:1.
[   13.984000] devtmpfs: mounted
[   13.988491] Freeing unused kernel memory: 336K
[   13.992952] Kernel memory protection not selected by kernel config.
[   13.999205] Run /sbin/init as init process
[   44.001882] watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [init:1]
[   44.008388] Modules linked in:
[   44.011437] CPU: 0 PID: 1 Comm: init Not tainted 5.8.0-1-ARCH #1
[   44.017416] Hardware name: Marvell Kirkwood (Flattened Device Tree)
[   44.023667] PC is at do_page_fault+0x64/0x350
[   44.028004] LR is at do_DataAbort+0x38/0xc0
[   44.032165] pc : [<c0010af8>]    lr : [<c0010f54>]    psr: 60000013
[   44.038403] sp : c7841dc0  ip : 80000013  fp : c7169200
[   44.043604] r10: b6fbf000  r9 : c7840000  r8 : c6c0c380
[   44.048806] r7 : c783d820  r6 : 00000805  r5 : b6ff1888  r4 : c7841e30
[   44.055303] r3 : 00000000  r2 : c7840000  r1 : 00000805  r0 : b6ff1888
[   44.061802] Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
[   44.068904] Control: 0005397f  Table: 06c10000  DAC: 00000051
[   44.074624] CPU: 0 PID: 1 Comm: init Not tainted 5.8.0-1-ARCH #1
[   44.080599] Hardware name: Marvell Kirkwood (Flattened Device Tree)
[   44.086867] [<c00101ac>] (unwind_backtrace) from [<c000cef8>] (show_stack+0x10/0x14)
[   44.094584] [<c000cef8>] (show_stack) from [<c00aa478>] (watchdog_timer_fn+0x190/0x1e4)
[   44.102571] [<c00aa478>] (watchdog_timer_fn) from [<c0071c68>] (__hrtimer_run_queues.constprop.0+0x120/0x1b8)
[   44.112454] [<c0071c68>] (__hrtimer_run_queues.constprop.0) from [<c00726c8>] (hrtimer_interrupt+0x104/0x28c)
[   44.122350] [<c00726c8>] (hrtimer_interrupt) from [<c07786bc>] (orion_clkevt_irq_handler+0x10/0x1c)
[   44.131370] [<c07786bc>] (orion_clkevt_irq_handler) from [<c0063dac>] (__handle_irq_event_percpu+0x3c/0x140)
[   44.141160] [<c0063dac>] (__handle_irq_event_percpu) from [<c0063edc>] (handle_irq_event_percpu+0x2c/0x88)
[   44.150775] [<c0063edc>] (handle_irq_event_percpu) from [<c0063f60>] (handle_irq_event+0x28/0x3c)
[   44.159618] [<c0063f60>] (handle_irq_event) from [<c0067a08>] (handle_edge_irq+0x90/0x1c8)
[   44.167849] [<c0067a08>] (handle_edge_irq) from [<c00631dc>] (generic_handle_irq+0x30/0x44)
[   44.176174] [<c00631dc>] (generic_handle_irq) from [<c0485a9c>] (orion_bridge_irq_handler+0x4c/0x58)
[   44.185268] [<c0485a9c>] (orion_bridge_irq_handler) from [<c00631dc>] (generic_handle_irq+0x30/0x44)
[   44.194363] [<c00631dc>] (generic_handle_irq) from [<c00637a4>] (__handle_domain_irq+0x48/0xa4)
[   44.203030] [<c00637a4>] (__handle_domain_irq) from [<c0485a2c>] (orion_handle_irq+0x68/0x8c)
[   44.211524] [<c0485a2c>] (orion_handle_irq) from [<c0008f28>] (__irq_svc+0x68/0x84)
[   44.219145] Exception stack(0xc7841d70 to 0xc7841db8)
[   44.224176] 1d60:                                     b6ff1888 00000805 c7840000 00000000
[   44.232320] 1d80: c7841e30 b6ff1888 00000805 c783d820 c6c0c380 c7840000 b6fbf000 c7169200
[   44.240464] 1da0: 80000013 c7841dc0 c0010f54 c0010af8 60000013 ffffffff
[   44.247051] [<c0008f28>] (__irq_svc) from [<c0010af8>] (do_page_fault+0x64/0x350)
[   44.254506] [<c0010af8>] (do_page_fault) from [<c0010f54>] (do_DataAbort+0x38/0xc0)
[   44.262133] [<c0010f54>] (do_DataAbort) from [<c0008e8c>] (__dabt_svc+0x6c/0xa0)
[   44.269488] Exception stack(0xc7841e30 to 0xc7841e78)
[   44.274521] 1e20:                                     00000000 60000013 00000055 00000055
[   44.282664] 1e40: 00000000 c7840000 b6ff1888 00000778 c732d700 00000003 b6fbf000 c7169200
[   44.290809] 1e60: 000005b7 c7841e80 c0409e8c c0409ea0 80000013 ffffffff
[   44.297400] [<c0008e8c>] (__dabt_svc) from [<c0409ea0>] (__clear_user_memset+0xb0/0x168)
[   44.305460] [<c0409ea0>] (__clear_user_memset) from [<c01d4f7c>] (load_elf_binary+0x13bc/0x13cc)
[   44.314214] [<c01d4f7c>] (load_elf_binary) from [<c01710bc>] (__do_execve_file+0x5a4/0x93c)
[   44.322530] [<c01710bc>] (__do_execve_file) from [<c01714fc>] (do_execve+0x2c/0x34)
[   44.330159] [<c01714fc>] (do_execve) from [<c0009c2c>] (try_to_run_init_process+0xc/0x38)
[   44.338313] [<c0009c2c>] (try_to_run_init_process) from [<c098e250>] (kernel_init+0x7c/0xec)
[   44.346722] [<c098e250>] (kernel_init) from [<c0008560>] (ret_from_fork+0x14/0x34)
[   44.354255] Exception stack(0xc7841fb0 to 0xc7841ff8)
[   44.359287] 1fa0:                                     00000000 00000000 00000000 00000000
[   44.367430] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[   44.375575] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[   72.001874] watchdog: BUG: soft lockup - CPU#0 stuck for 23s! [init:1]
[   72.008371] Modules linked in:
[   72.011418] CPU: 0 PID: 1 Comm: init Tainted: G             L    5.8.0-1-ARCH #1
[   72.018774] Hardware name: Marvell Kirkwood (Flattened Device Tree)
[   72.025024] PC is at ptep_set_access_flags+0xc/0x60
[   72.029892] LR is at handle_mm_fault+0x1c0/0xbac
[   72.034483] pc : [<c013991c>]    lr : [<c0130238>]    psr: 60000013
[   72.040720] sp : c7841d50  ip : 0128614f  fp : 00000215
[   72.045922] r10: 00000800  r9 : c6c0c3bc  r8 : c6c0c380
[   72.051124] r7 : 00000000  r6 : 00000215  r5 : b6ff1000  r4 : c6c0dea0
[   72.057621] r3 : 0128614f  r2 : c6c327c4  r1 : b6ff1000  r0 : c6c0dea0
[   72.064119] Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
[   72.071222] Control: 0005397f  Table: 06c10000  DAC: 00000051
[   72.076943] CPU: 0 PID: 1 Comm: init Tainted: G             L    5.8.0-1-ARCH #1
[   72.084299] Hardware name: Marvell Kirkwood (Flattened Device Tree)
[   72.090554] [<c00101ac>] (unwind_backtrace) from [<c000cef8>] (show_stack+0x10/0x14)
[   72.098273] [<c000cef8>] (show_stack) from [<c00aa478>] (watchdog_timer_fn+0x190/0x1e4)
[   72.106252] [<c00aa478>] (watchdog_timer_fn) from [<c0071c68>] (__hrtimer_run_queues.constprop.0+0x120/0x1b8)
[   72.116135] [<c0071c68>] (__hrtimer_run_queues.constprop.0) from [<c00726c8>] (hrtimer_interrupt+0x104/0x28c)
[   72.126014] [<c00726c8>] (hrtimer_interrupt) from [<c07786bc>] (orion_clkevt_irq_handler+0x10/0x1c)
[   72.135031] [<c07786bc>] (orion_clkevt_irq_handler) from [<c0063dac>] (__handle_irq_event_percpu+0x3c/0x140)
[   72.144817] [<c0063dac>] (__handle_irq_event_percpu) from [<c0063edc>] (handle_irq_event_percpu+0x2c/0x88)
[   72.154431] [<c0063edc>] (handle_irq_event_percpu) from [<c0063f60>] (handle_irq_event+0x28/0x3c)
[   72.163271] [<c0063f60>] (handle_irq_event) from [<c0067a08>] (handle_edge_irq+0x90/0x1c8)
[   72.171505] [<c0067a08>] (handle_edge_irq) from [<c00631dc>] (generic_handle_irq+0x30/0x44)
[   72.179827] [<c00631dc>] (generic_handle_irq) from [<c0485a9c>] (orion_bridge_irq_handler+0x4c/0x58)
[   72.188924] [<c0485a9c>] (orion_bridge_irq_handler) from [<c00631dc>] (generic_handle_irq+0x30/0x44)
[   72.198021] [<c00631dc>] (generic_handle_irq) from [<c00637a4>] (__handle_domain_irq+0x48/0xa4)
[   72.206686] [<c00637a4>] (__handle_domain_irq) from [<c0485a2c>] (orion_handle_irq+0x68/0x8c)
[   72.215180] [<c0485a2c>] (orion_handle_irq) from [<c0008f28>] (__irq_svc+0x68/0x84)
[   72.222800] Exception stack(0xc7841d00 to 0xc7841d48)
[   72.227837] 1d00: c6c0dea0 b6ff1000 c6c327c4 0128614f c6c0dea0 b6ff1000 00000215 00000000
[   72.235984] 1d20: c6c0c380 c6c0c3bc 00000800 00000215 0128614f c7841d50 c0130238 c013991c
[   72.244124] 1d40: 60000013 ffffffff
[   72.247606] [<c0008f28>] (__irq_svc) from [<c013991c>] (ptep_set_access_flags+0xc/0x60)
[   72.255585] [<c013991c>] (ptep_set_access_flags) from [<c0130238>] (handle_mm_fault+0x1c0/0xbac)
[   72.264334] [<c0130238>] (handle_mm_fault) from [<c0010ba8>] (do_page_fault+0x114/0x350)
[   72.272392] [<c0010ba8>] (do_page_fault) from [<c0010f54>] (do_DataAbort+0x38/0xc0)
[   72.280022] [<c0010f54>] (do_DataAbort) from [<c0008e8c>] (__dabt_svc+0x6c/0xa0)
[   72.287384] Exception stack(0xc7841e30 to 0xc7841e78)
[   72.292416] 1e20:                                     00000000 60000013 00000055 00000055
[   72.300559] 1e40: 00000000 c7840000 b6ff1888 00000778 c732d700 00000003 b6fbf000 c7169200
[   72.308705] 1e60: 000005b7 c7841e80 c0409e8c c0409ea0 80000013 ffffffff
[   72.315293] [<c0008e8c>] (__dabt_svc) from [<c0409ea0>] (__clear_user_memset+0xb0/0x168)
[   72.323353] [<c0409ea0>] (__clear_user_memset) from [<c01d4f7c>] (load_elf_binary+0x13bc/0x13cc)
[   72.332106] [<c01d4f7c>] (load_elf_binary) from [<c01710bc>] (__do_execve_file+0x5a4/0x93c)
[   72.340425] [<c01710bc>] (__do_execve_file) from [<c01714fc>] (do_execve+0x2c/0x34)
[   72.348055] [<c01714fc>] (do_execve) from [<c0009c2c>] (try_to_run_init_process+0xc/0x38)
[   72.356204] [<c0009c2c>] (try_to_run_init_process) from [<c098e250>] (kernel_init+0x7c/0xec)
[   72.364608] [<c098e250>] (kernel_init) from [<c0008560>] (ret_from_fork+0x14/0x34)
[   72.372142] Exception stack(0xc7841fb0 to 0xc7841ff8)
[   72.377174] 1fa0:                                     00000000 00000000 00000000 00000000
[   72.385317] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[   72.393463] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000

and here is the log from the flash card:

U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45)
Pogoplug V4

SoC:   Kirkwood 88F6192_A1
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  128 MiB
MMC:   kwsdio: 0
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Hit any key to stop autoboot: 0 

MMC rescan: current device # 0 initialized OK
4966364 bytes read in 1396 ms (3.4 MiB/s)
** File not found /boot/uInitrd **
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-5.8.0-1-ARCH
   Created:      2021-01-15   5:57:35 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4966300 Bytes = 4.7 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
Using machid 0xf78 from environment

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.8.0-1-ARCH (builduser@leming) (armv5tel-unknown-linux-gnueabi-gcc (GCC) 9.3.0, GNU ld (GNU Binutils) 2.34) #1 Sun Aug 9 03:29:09 UTC 2020
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] OF: fdt: Machine model: Cloud Engines PogoPlug Series 4
[    0.000000] Memory policy: Data cache writeback
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p1 rootdelay=10 rootfstype=ext3 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 115388K/131072K available (9771K kernel code, 349K rwdata, 3404K rodata, 336K init, 197K bss, 15684K reserved, 0K cma-reserved)
[    0.000000] random: get_random_u32 called from cache_random_seq_create+0x80/0x134 with crng_init=0
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[    0.000013] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[    0.000061] Switching to timer-based delay loop, resolution 6ns
[    0.000400] Console: colour dummy device 80x30
[    0.000468] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666)
[    0.000499] pid_max: default: 32768 minimum: 301
[    0.001191] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.001224] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.003215] CPU: Testing write buffer coherency: ok
[    0.004612] Setting up static identity map for 0x8400 - 0x847c
[    0.005002] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[    0.005910] devtmpfs: initialized
[    0.011090] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.011129] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.011497] pinctrl core: initialized pinctrl subsystem
[    0.012570] thermal_sys: Registered thermal governor 'step_wise'
[    0.013626] NET: Registered protocol family 16
[    0.014491] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.015536] audit: initializing netlink subsys (disabled)
[    0.017216] cpuidle: using governor ladder
[    0.017240] cpuidle: using governor menu
[    0.017933] Feroceon L2: Enabling L2
[    0.017992] Feroceon L2: Cache support initialised.
[    0.030316] No ATAGs?
[    0.030852] Serial: AMBA PL011 UART driver
[    0.041062] audit: type=2000 audit(0.010:1): state=initialized audit_enabled=0 res=1
[    0.047899] AT91: Could not find identification node
[    0.048396] vgaarb: loaded
[    0.048984] SCSI subsystem initialized
[    0.049614] usbcore: registered new interface driver usbfs
[    0.049686] usbcore: registered new interface driver hub
[    0.049752] usbcore: registered new device driver usb
[    0.050252] pps_core: LinuxPPS API ver. 1 registered
[    0.050263] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.050294] PTP clock support registered
[    0.050642] Advanced Linux Sound Architecture Driver Initialized.
[    0.051874] clocksource: Switched to clocksource orion_clocksource
[    0.052280] VFS: Disk quotas dquot_6.6.0
[    0.052383] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.063949] NET: Registered protocol family 2
[    0.064897] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.064988] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.065017] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.065044] TCP: Hash tables configured (established 1024 bind 1024)
[    0.065548] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.065582] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.065869] NET: Registered protocol family 1
[    0.066477] RPC: Registered named UNIX socket transport module.
[    0.066490] RPC: Registered udp transport module.
[    0.066499] RPC: Registered tcp transport module.
[    0.066506] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.066522] PCI: CLS 0 bytes, default 32
[    0.069059] Initialise system trusted keyrings
[    0.069307] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[    0.080819] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.082423] NFS: Registering the id_resolver key type
[    0.082469] Key type id_resolver registered
[    0.082477] Key type id_legacy registered
[    0.082499] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.082548] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.083335] fuse: init (API version 7.31)
[    0.274522] Key type asymmetric registered
[    0.274540] Asymmetric key parser 'x509' registered
[    0.274610] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    0.274770] io scheduler mq-deadline registered
[    0.274783] io scheduler kyber registered
[    0.275175] io scheduler bfq registered
[    0.276917] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[    0.279447] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00
[    0.279473] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.279490] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[    0.279505] pci_bus 0000:00: root bus resource [io  0x1000-0xeffff]
[    0.279642] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400
[    0.279691] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[    0.281225] PCI: bus0: Fast back to back transfers disabled
[    0.281248] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.281448] pci 0000:01:00.0: [1b73:1009] type 00 class 0x0c0330
[    0.281501] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x0000ffff 64bit]
[    0.281528] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit]
[    0.281554] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit]
[    0.281655] pci 0000:01:00.0: supports D1
[    0.281671] pci 0000:01:00.0: PME# supported from D0 D1 D3hot
[    0.281718] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[    0.313152] PCI: bus1: Fast back to back transfers disabled
[    0.313178] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    0.313463] pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe00fffff]
[    0.313484] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0100000-0xe01007ff pref]
[    0.313508] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff 64bit]
[    0.313536] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0010000-0xe0010fff 64bit]
[    0.313563] pci 0000:01:00.0: BAR 4: assigned [mem 0xe0011000-0xe0011fff 64bit]
[    0.313588] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.313608] pci 0000:00:01.0:   bridge window [mem 0xe0000000-0xe00fffff]
[    0.313688] pci 0000:00:01.0: enabling device (0140 -> 0142)
[    0.313718] pci 0000:01:00.0: enabling device (0140 -> 0142)
[    0.314568] mv_xor f1060800.xor: Marvell shared XOR driver
[    0.373027] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    0.373431] mv_xor f1060900.xor: Marvell shared XOR driver
[    0.433002] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    0.433644] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.435268] printk: console [ttyS0] disabled
[    0.435414] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 10416666) is a 16550A
[    1.184115] printk: console [ttyS0] enabled
[    1.193567] brd: module loaded
[    1.207526] loop: module loaded
[    1.211940] sata_mv f1080000.sata: slots 32 ports 1
[    1.218734] scsi host0: sata_mv
[    1.222373] ata1: SATA max UDMA/133 irq 32
[    1.227712] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[    1.234088] nand: Hynix H27U1G8F2BTR-BC
[    1.237908] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.245480] Scanning device for bad blocks
[    1.364382] 5 cmdlinepart partitions found on MTD device orion_nand
[    1.370624] Creating 5 MTD partitions on "orion_nand":
[    1.375764] 0x000000000000-0x000000200000 : "u-boot"
[    1.382902] 0x000000200000-0x000000500000 : "uImage"
[    1.389532] 0x000000500000-0x000000800000 : "uImage2"
[    1.396271] 0x000000800000-0x000001000000 : "failsafe"
[    1.403150] 0x000001000000-0x000008000000 : "root"
[    1.411714] libphy: Fixed MDIO Bus: probed
[    1.418777] libphy: orion_mdio_bus: probed
[    1.424504] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    1.713421] ata1: SATA link down (SStatus 0 SControl F300)
[    2.112673] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:05:f5:25
[    2.121933] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.128429] ehci-pci: EHCI PCI platform driver
[    2.132934] ehci-platform: EHCI generic platform driver
[    2.138274] ehci-orion: EHCI orion driver
[    2.142516] orion-ehci f1050000.ehci: EHCI Host Controller
[    2.148015] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    2.155872] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
[    2.181915] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    2.188121] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08
[    2.196383] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.203594] usb usb1: Product: EHCI Host Controller
[    2.208449] usb usb1: Manufacturer: Linux 5.8.0-1-ARCH ehci_hcd
[    2.214360] usb usb1: SerialNumber: f1050000.ehci
[    2.219798] hub 1-0:1.0: USB hub found
[    2.223626] hub 1-0:1.0: 1 port detected
[    2.228149] ehci-atmel: EHCI Atmel driver
[    2.232287] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.238465] ohci-pci: OHCI PCI platform driver
[    2.242982] ohci-platform: OHCI generic platform driver
[    2.248304] ohci-atmel: OHCI Atmel driver
[    2.252686] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    2.257920] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[    2.266647] xhci_hcd 0000:01:00.0: hcc params 0x200073a1 hci version 0x100 quirks 0x0000000000080010
[    2.276322] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08
[    2.284583] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.291773] usb usb2: Product: xHCI Host Controller
[    2.296647] usb usb2: Manufacturer: Linux 5.8.0-1-ARCH xhci-hcd
[    2.302554] usb usb2: SerialNumber: 0000:01:00.0
[    2.307852] hub 2-0:1.0: USB hub found
[    2.311635] hub 2-0:1.0: 2 ports detected
[    2.316364] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    2.321587] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3
[    2.328994] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed
[    2.335810] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.344059] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.08
[    2.352312] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.359502] usb usb3: Product: xHCI Host Controller
[    2.364375] usb usb3: Manufacturer: Linux 5.8.0-1-ARCH xhci-hcd
[    2.370267] usb usb3: SerialNumber: 0000:01:00.0
[    2.375534] hub 3-0:1.0: USB hub found
[    2.379309] hub 3-0:1.0: 2 ports detected
[    2.384123] usbcore: registered new interface driver cdc_acm
[    2.389754] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    2.398028] usbcore: registered new interface driver uas
[    2.403544] usbcore: registered new interface driver usb-storage
[    2.409568] usbcore: registered new interface driver ums-alauda
[    2.415535] usbcore: registered new interface driver ums-cypress
[    2.421564] usbcore: registered new interface driver ums-datafab
[    2.427625] usbcore: registered new interface driver ums_eneub6250
[    2.433846] usbcore: registered new interface driver ums-freecom
[    2.439870] usbcore: registered new interface driver ums-isd200
[    2.445828] usbcore: registered new interface driver ums-jumpshot
[    2.451962] usbcore: registered new interface driver ums-karma
[    2.457814] usbcore: registered new interface driver ums-onetouch
[    2.463965] usbcore: registered new interface driver ums-realtek
[    2.469989] usbcore: registered new interface driver ums-sddr09
[    2.475951] usbcore: registered new interface driver ums-sddr55
[    2.481911] usbcore: registered new interface driver ums-usbat
[    2.487848] usbcore: registered new interface driver usbserial_generic
[    2.494407] usbserial: USB Serial support registered for generic
[    2.500441] usbcore: registered new interface driver ftdi_sio
[    2.506221] usbserial: USB Serial support registered for FTDI USB Serial Device
[    2.513855] usbcore: registered new interface driver pl2303
[    2.519441] usbserial: USB Serial support registered for pl2303
[    2.527582] mousedev: PS/2 mouse device common for all mice
[    3.601928] rtc-mv f1010300.rtc: internal RTC not ticking
[    3.607575] i2c /dev entries driver
[    3.611092] Driver for 1-wire Dallas network protocol.
[    3.618053] orion_wdt: Initial timeout 25 sec
[    3.623722] sdhci: Secure Digital Host Controller Interface driver
[    3.629878] sdhci: Copyright(c) Pierre Ossman
[    3.634710] mvsdio f1090000.mvsdio: Got CD GPIO
[    3.639253] mvsdio f1090000.mvsdio: Got WP GPIO
[    3.669627] sdhci-pltfm: SDHCI platform and OF driver helper
[    3.676264] ledtrig-cpu: registered to indicate activity on CPUs
[    3.684751] marvell-cesa f1030000.crypto: CESA device successfully registered
[    3.692298] hid: raw HID events driver (C) Jiri Kosina
[    3.697589] usbcore: registered new interface driver usbhid
[    3.703169] usbhid: USB HID core driver
[    3.710265] NET: Registered protocol family 10
[    3.718253] Segment Routing with IPv6
[    3.722078] NET: Registered protocol family 17
[    3.726747] Key type dns_resolver registered
[    3.731602] registered taskstats version 1
[    3.735761] Loading compiled-in X.509 certificates
[    3.740819] Key type ._fscrypt registered
[    3.744841] Key type .fscrypt registered
[    3.748749] Key type fscrypt-provisioning registered
[    3.756582] random: fast init done
[    3.761436] Key type encrypted registered
[    3.768038] printk: console [netcon0] enabled
[    3.772425] netconsole: network logging started
[    3.777630] input: gpio_keys as /devices/platform/gpio_keys/input/input0
[    3.785112] ALSA device list:
[    3.788070]   No soundcards found.
[    3.791756] Waiting 10 sec before mounting root device...
[    3.809187] mmc0: new high speed SDHC card at address 1234
[    3.815373] mmcblk0: mmc0:1234 SA04G 3.69 GiB 
[    3.824155]  mmcblk0: p1
[   13.924727] List of all partitions:
[   13.928220] 0100            8192 ram0 
[   13.928224]  (driver?)
[   13.934349] 0101            8192 ram1 
[   13.934352]  (driver?)
[   13.940428] 0102            8192 ram2 
[   13.940431]  (driver?)
[   13.946538] 0103            8192 ram3 
[   13.946542]  (driver?)
[   13.952644] 1f00            2048 mtdblock0 
[   13.952648]  (driver?)
[   13.959160] 1f01            3072 mtdblock1 
[   13.959163]  (driver?)
[   13.965694] 1f02            3072 mtdblock2 
[   13.965697]  (driver?)
[   13.972225] 1f03            8192 mtdblock3 
[   13.972229]  (driver?)
[   13.978739] 1f04          114688 mtdblock4 
[   13.978741]  (driver?)
[   13.985271] b300         3864576 mmcblk0 
[   13.985275]  driver: mmcblk
[   13.992062]   b301         3864308 mmcblk0p1 07f2c1f7-01
[   13.992066] 
[   13.998829] No filesystem could mount root, tried: 
[   13.998832]  ext3
[   14.003703] 
[   14.007103] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,1)
[   14.015504] CPU: 0 PID: 1 Comm: swapper Not tainted 5.8.0-1-ARCH #1
[   14.021742] Hardware name: Marvell Kirkwood (Flattened Device Tree)
[   14.028019] [<c00101ac>] (unwind_backtrace) from [<c000cef8>] (show_stack+0x10/0x14)
[   14.035740] [<c000cef8>] (show_stack) from [<c0025648>] (panic+0xe8/0x304)
[   14.042607] [<c0025648>] (panic) from [<c0d27a18>] (mount_block_root+0x238/0x278)
[   14.050069] [<c0d27a18>] (mount_block_root) from [<c0d27ca4>] (mount_root+0xf8/0x13c)
[   14.057870] [<c0d27ca4>] (mount_root) from [<c0d27e44>] (prepare_namespace+0x15c/0x1b4)
[   14.065849] [<c0d27e44>] (prepare_namespace) from [<c098e1dc>] (kernel_init+0x8/0xec)
[   14.073654] [<c098e1dc>] (kernel_init) from [<c0008560>] (ret_from_fork+0x14/0x34)
[   14.081187] Exception stack(0xc7841fb0 to 0xc7841ff8)
[   14.086219] 1fa0:                                     00000000 00000000 00000000 00000000
[   14.094362] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[   14.102507] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[   14.109100] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,1) ]---

Any more ideas?

Rhodess,

The SD card boot is actually is a litle bit better.

But at this point, you are seeing the same error with both USB and SD card. So I wonder whether this new Arch rootfs has some particular problem with this Pogo V4 box.

What you should do is to boot with the rootfs Debian-5.2.9-kirkwood-tld-1-rootfs-bodhi.tar.bz2 on USB to confirm that the box is OK. And then go from there.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Thanks bodhi, I’ll read up on what I need to do to go that route then. Thanks for your patience

Hi bodhi, I just read through your post and to ensure I don't mess anything up, do I need to flash back to factory first, or am I OK to do this with my existing uboot?

Rhodess,

> Hi bodhi, I just read through your post and to
> ensure I don't mess anything up, do I need to
> flash back to factory first, or am I OK to do this
> with my existing uboot?

If you create Debian rootfs on SD card then it will run the same way with your current u-boot settings. No need to adjust anything.

Quote
https://forum.doozan.com/read.php?2,12096

Step 4 needs adjustment like this:

4. Create uImage with embedded DTB for booting with older u-boots (2012 or earlier). Do not do this step if you have installed the latest U-Boot for Kirkwood (or are installing this u-boot at the same time).

Please replace kirkwood-goflexnet.dtb below with the correct DTB name for your box (see the folder /media/sdb1/boot/dts for the exact spelling of your Kirkwood box name).

Generate the uImage with DTB embedded inside:
cd /media/sdb1/boot
cp -a zImage-5.2.9-kirkwood-tld-1 zImage.fdt
cat dts/kirkwood-pogoplug_v4.dtb >> zImage.fdt
mv uImage uImage.orig
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-5.2.9-kirkwood-tld-1 -d zImage.fdt uImage
sync

After that bring the SD card to this box and power up. Watch serial console log and see if it will boot all the way into Debian.

========

Once you are in Debian, install the latest u-boot version. Note that after you installed new u-boot, and before reboot, you have to restore the original uImage (since the new u-boot will load the DTB file separately).

cd /boot
cp -a uImage uImage.pogo_v4
cp -a uImage.orig uImage

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Hi bodhi,

Its currently stuck at booting the kernel:

U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45)
Pogoplug V4

SoC:   Kirkwood 88F6192_A1
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  128 MiB
MMC:   kwsdio: 0
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Hit any key to stop autoboot: 0 

MMC rescan: current device # 0 initialized OK
4973642 bytes read in 1699 ms (2.8 MiB/s)
9713936 bytes read in 1809 ms (5.1 MiB/s)
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-5.2.9-kirkwood-tld-1
   Created:      2021-01-16   4:40:19 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4973578 Bytes = 4.7 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
   Image Name:   initramfs-5.2.9-kirkwood-tld-1
   Created:      2019-08-25   2:22:50 UTC
   Image Type:   ARM Linux RamDisk Image (gzip compressed)
   Data Size:    9713872 Bytes = 9.3 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
Using machid 0xf78 from environment

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

Rhodess,

You're almost there!

Power up, interrupt serial console.

And then change these 3 envs:

setenv set_bootargs_mmc 'setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts earlyprintk=serial'
setenv mmc_load_uinitrd 'ext2load mmc $device 0x2100000 /boot/uInitrd'
setenv mmc_boot 'mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x2100000; else bootm 0x800000; fi'

And do printenv again so I don't have to scroll back to previous posts to find it next time when needed :).

printenv

And then boot

boot

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

I'm in! The changes you gave me allowed it to boot up, so I'm now into Debian. Heres my print_env:

arcNumber=3960
baudrate=115200
bootcmd=run bootcmd_mmc; run bootcmd_usb; run bootcmd_sata; run bootcmd_pogo; reset
bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot
bootcmd_pogo=if ubi part root 2048 && ubifsmount ubi:rootfs && ubifsload 0x800000 uboot.mtd0.dockstar.original.kwb ; then go 0x800200; fi
bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot;
bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot;
bootdelay=10
console=ttyS0,115200
device=0:1
ethact=egiga0
ethaddr=00:25:31:05:f5:25
if_netconsole=ping $serverip
ipaddr=10.0.1.220
led_error=orange blinking
led_exit=green off
led_init=green blinking
machid=F78
mainlineLinux=yes
mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x2100000; else bootm 0x800000; fi
mmc_init=mmc rescan
mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage
mmc_load_uinitrd=ext2load mmc $device 0x2100000 /boot/uInitrd
mmc_root=/dev/mmcblk0p1
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root
partition=nand0,2
preboot_nc=run if_netconsole start_netconsole
rootdelay=10
rootfstype=ext3
sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
sata_init=ide reset
sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage
sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd
sata_root=/dev/sda1
serverip=10.0.1.231
set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts earlyprintk=serial
set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
usb_init=usb start
usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage
usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd
usb_root=/dev/sda1
usb_rootfstype=ext3

Environment size: 2428/131068 bytes

I'm currently logged in as root. I haven't updated or changed anything yet since in the previous post you wanted me to install the latest uboot version and then restore the original image.

Also in the post you referred me to it says to generate new ssh keys and upgrade. I didn't want to risk that at this point though since I don't know if you want to make further changes.



Edited 1 time(s). Last edit at 01/16/2021 01:13AM by Rhodess.

Rhodess,

> I'm in! The changes you gave me allowed it to boot
> up, so I'm now into Debian.

Cool!

> Also in the post you referred me to it says to
> generate new ssh keys and upgrade. I didn't want
> to risk that at this point though since I don't
> know if you want to make further changes.

Yes, do generate new ssh keys so you know you have a Debian system of your own. No need to upgrade yet, though.

> I'm currently logged in as root. I haven't updated or changed anything yet since in the previous post you wanted me to install the latest uboot version and then restore the
> original image.

OK. So now we know the new Arch rootfs has some problem booting with this box. Not sure it is a common problem for all Kirkwood boxes, or just this Pogo V4.

At this point, you will need to make a decision whether to pursue running Arch rootfs, or run Debian. Let me know which is your preference.

=========

For both Arch or Debian, running new u-boot is better. But it will need some adjustment again to be able to boot Arch, if you plan to do so. The new u-boot will work for this Debian rootfs for sure. (Note that your Debian rootfs right now has the DTB embedded inside uImage, with new u-boot, you need to reverse Step 4, i.e. restore the original uImage).

If you decide to install new u-boot, then try UART booting using kwboot first, to ensure you have a rescue path. Here is an example for kwboot booting:

https://forum.doozan.com/read.php?3,51739,51919#msg-51919

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Thanks bodhi,

I have no preference really, either Arch or Debian. My main goal was to boot from the sd card, the assumption being that the port is less likely to be used vs the USB ports. so once I have it all running properly I intend to image the flash card for recovery/backup incase my sd card gets damaged, and also have it boot native, but without all the pogo services running.

Reading through the posts and Arch wiki, there are pro's and cons for both Arch and Debian. Since it will never be a pogo again, on account the company is bust, for me, usage would be a samba server, print server, possibly router etc.

So which would be the best for that, if either, then I would go for the one that's least likely to fail due to upgrades, or easier to recover etc.

I will go for the new u-boot though,which I assume is this one "uboot.2017.07-tld-1.pogo_v4.bodhi.tar" md5:e2c2b4927dcd8189f0c97dd81b72ad7e from uboot.2017.07-tld-1.pogo_v4.bodhi.tar, correct?

To summarise then, I would need to do the following, dependent on the Linux version:
Debian:
1. download kwboot-2016.05.tar and follow this UART Booting HowTo for Selected Kirkwood Devices
2. Make the setenv change for pogoplug v4 via this thread Need help/advice on brand new pogoplugV4
3. Install uboot.2017.07-tld-1.pogo_v4.bodhi.tar following steps 1-11
4. Restore the original uImage
5. Reboot

Arch:
Same as above, but adding additional changes to the pogo environment before proceeding with step 1.

Have I understood everything correctly?

Rhodess,

> I will go for the new u-boot though,which I assume
> is this one
> "uboot.2017.07-tld-1.pogo_v4.bodhi.tar"
> md5:e2c2b4927dcd8189f0c97dd81b72ad7e from
> uboot.2017.07-tld-1.pogo_v4.bodhi.tar,
> correct?

Correct.

> To summarise then, I would need to do the
> following, dependent on the Linux version:
> Debian:

> 1. download kwboot-2016.05.tar and follow this
> UART
> Booting HowTo for Selected Kirkwood Devices

Yes. That davygravy's post and the link I posted above: https://forum.doozan.com/read.php?3,51739,51919#msg-51919


> 2. Make the setenv change for pogoplug v4 via this
> thread
> Need
> help/advice on brand new pogoplugV4

No. You don't need to do any change in envs before installing new u-boot.

> 3. Install uboot.2017.07-tld-1.pogo_v4.bodhi.tar
> following steps 1-11

Step 1 to 11 includes every necessary envs change to the installed default envs image to boot this Pogo V4 box.

> 4. Restore the original uImage

Yes.

> 5. Reboot
>
> Arch:
> Same as above, but adding additional changes to
> the pogo environment before proceeding with step
> 1.

No, complete the installation steps 1 to 11 first. And then modify a couple additional envs. This can be done later quite easily with uEnv.txt or permanent to flash.

So install it to boot Debian first. And then worry about Arch later.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)