DS210j - flash chip failure and image rebuilding February 25, 2021 02:58PM |
Registered: 3 years ago Posts: 11 |
Re: DS210j - flash chip failure and image rebuilding February 25, 2021 04:05PM |
Admin Registered: 13 years ago Posts: 19,114 |
> 0x00000000-0x00080000 : "RedBoot" > 0x00080000-0x00280000 : "zImage" > 0x00280000-0x003c0000 : "rd.gz" > 0x003c0000-0x003d0000 : "vendor" > 0x003d0000-0x003f0000 : "RedBoot Config" > 0x003f0000-0x00400000 : "FIS directory"
[ 7.364601][ T1] 0x000000000000-0x000000080000 : "RedBoot" [ 7.371383][ T1] 0x000000080000-0x000000280000 : "zImage" [ 7.377942][ T1] 0x000000280000-0x0000003c0000 : "rd.gz" [ 7.384453][ T1] 0x0000003c0000-0x0000003d0000 : "vendor" [ 7.391052][ T1] 0x0000003d0000-0x0000003f0000 : "RedBoot config" [ 7.398293][ T1] 0x0000003f0000-0x000000400000 : "FIS directory"
Re: DS210j - flash chip failure and image rebuilding March 01, 2021 01:58PM |
Registered: 3 years ago Posts: 11 |
U-Boot 2015.10-tld-1 (Nov 06 2015 - 16:19:43 -0800) ZyXEL NSA310 1-Bay Power Media Server SoC: Kirkwood 88F6281_A1 DRAM: 256 MiB (ECC not enabled) WARNING: Caches not enabled NAND: 0 MiB *** Warning - readenv() failed, using default environment In: serial Out: serial Err: serial Net: egiga0 PHY reset timed out MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 NSA310>Should i see SPI flash memory in log at this moment? Since old flash chip was fried i'm afraid of damaged CPUs SPI interface. "sflash info" gives unknown command.
Re: DS210j - flash chip failure and image rebuilding March 01, 2021 04:15PM |
Admin Registered: 13 years ago Posts: 19,114 |
Re: DS210j - flash chip failure and image rebuilding March 02, 2021 01:52PM |
Registered: 3 years ago Posts: 11 |
Tried as well. T5325 does not boot, dreamplug stops at ram detection. Pitty, because SPI was ready according to log ;)Quote
bodhi
have you tried
> uboot.2017.07-tld-1.t5325.mtd0.kwb or
> uboot.2017.07-tld-1.dreamplug.mtd0.kwb?
Re: DS210j - flash chip failure and image rebuilding March 02, 2021 04:09PM |
Admin Registered: 13 years ago Posts: 19,114 |
Re: DS210j - flash chip failure and image rebuilding March 03, 2021 02:02PM |
Registered: 3 years ago Posts: 11 |
U-Boot 2015.10-tld-1 (Nov 06 2015 - 16:19:43 -0800) ZyXEL NSA310 1-Bay Power Media Server SoC: Kirkwood 88F6281_A1 DRAM: 256 MiB (ECC not enabled) WARNING: Caches not enabled NAND: 0 MiB *** Warning - readenv() failed, using default environment In: serial Out: serial Err: serial Net: egiga0 PHY reset timed out MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 NSA310> setenv ipaddr 192.168.1.50 NSA310> setenv serverip 192.168.1.10 NSA310> tftpboot 0x2000000 zImage Using egiga0 device TFTP from server 192.168.1.10; our IP address is 192.168.1.50 Filename 'zImage'. Load address: 0x2000000 Loading: T TFTP error: First block is not block 1 (0) Starting again NSA310> tftpboot 0x2000000 zImage Using egiga0 device TFTP from server 192.168.1.10; our IP address is 192.168.1.50 Filename 'zImage'. Load address: 0x2000000 Loading: ################################################################# ######################################### 7.5 MiB/s done Bytes transferred = 1551032 (17aab8 hex) NSA310> tftpboot 0x8000000 rd.bin Using egiga0 device TFTP from server 192.168.1.10; our IP address is 192.168.1.50 Filename 'rd.bin'. Load address: 0x8000000 Loading: ################################################################# ### 7.5 MiB/s done Bytes transferred = 995110 (f2f26 hex) NSA310> bootm 0x2000000 0x8000000 ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-2.6.32.12 Created: 2016-04-26 8:30:18 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1550968 Bytes = 1.5 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 08000000 ... Image Name: synology_88f6281_210j 5967 Created: 2016-04-26 9:42:51 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 995046 Bytes = 971.7 KiB Load Address: 00800000 Entry Point: 00800000 Verifying Checksum ... OK Loading Kernel Image ... OK Using machid 0x118f from environment Starting kernel ... Uncompressing Linux... done, booting the kernel.
Re: DS210j - flash chip failure and image rebuilding April 29, 2021 01:05PM |
Registered: 3 years ago Posts: 11 |
__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** ** MARVELL BOARD: Synology Disk Station LE U-Boot 1.1.4 (Apr 3 2012 - 20:15:28) Marvell version: 3.4.4 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 0068B43C Soc: 88F6281 A1 (DDR2) CPU running @ 800Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 6 tRP = 6 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 128MB DRAM CS[1] base 0x08000000 size 128MB DRAM Total size 256MB 16bit width [4096kB@f8000000] Flash: 4 MB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done Using default environment CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled Module 1 is AUDIO USB 0: host mode PEX 0: interface detected no Link. Synology Model: DS212j Fan Status: Not Good Fan 1: Not Good Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 ## Booting image at f8080000 ... Image Name: Linux-2.6.32.12 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1550968 Bytes = 1.5 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at f8280000 ... Image Name: synology_88f6281_210j 5967 Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 995046 Bytes = 971.7 kB Load Address: 00800000 Entry Point: 00800000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel.
Re: DS210j - flash chip failure and image rebuilding April 29, 2021 06:25PM |
Admin Registered: 13 years ago Posts: 19,114 |
Quote
> U-Boot 1.1.4 (Apr 3 2012 - 20:15:28) Marvell version: 3.4.4
....
> Hit any key to stop autoboot: 0
printenv
Re: DS210j - flash chip failure and image rebuilding April 30, 2021 11:09AM |
Registered: 3 years ago Posts: 11 |
Marvell>> printenv bootcmd=bootm F8080000 F8280000 baudrate=115200 loads_echo=0 ipaddr=192.168.101.224 serverip=192.168.101.111 rootpath=/mnt/ARM_FS/ netmask=255.255.0.0 stdin=serial stdout=serial stderr=serial console=console=ttyS0,115200 mtdparts=cfi_flash:0x380000(root),0x80000(uboot)ro mainlineLinux=no CASset=min enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes MALLOC_len=1 ethprime=egiga0 netbsd_en=no vxworks_en=no bootargs_root=root=/dev/nfs rw bootargs_end=:::DB88FXX81:egiga0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; bootdelay=3 disaMvPnp=no mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxo mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host bootargs=console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw syno_hw_version=DS212j ihd_num=2 netif_num=1 ethact=egiga0 ethaddr=00:00:5f:ff:00:00 eth1addr=00:01:5f:ff:00:01 Environment size: 1095/4092 bytes
Re: DS210j - flash chip failure and image rebuilding April 30, 2021 05:19PM |
Admin Registered: 13 years ago Posts: 19,114 |
bootargs=console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw syno_hw_version=DS212j ihd_num=2 netif_num=1
setenv bootargs 'console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw syno_hw_version=DS212j ihd_num=2 netif_num=1 earlyprintk=serial'
boot
Re: DS210j - flash chip failure and image rebuilding May 03, 2021 04:41AM |
Registered: 3 years ago Posts: 11 |
Marvell>> setenv bootargs 'console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw syno_hw_version=DS212j ihd_num=2 netif_num=1 earlyprintk=serial' Marvell>> printenv bootcmd=bootm F8080000 F8280000 baudrate=115200 loads_echo=0 ipaddr=192.168.101.224 serverip=192.168.101.111 rootpath=/mnt/ARM_FS/ netmask=255.255.0.0 stdin=serial stdout=serial stderr=serial console=console=ttyS0,115200 mtdparts=cfi_flash:0x380000(root),0x80000(uboot)ro mainlineLinux=no CASset=min enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes MALLOC_len=1 ethprime=egiga0 netbsd_en=no vxworks_en=no bootargs_root=root=/dev/nfs rw bootargs_end=:::DB88FXX81:egiga0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; bootdelay=3 disaMvPnp=no mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxo mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host ethact=egiga0 ethaddr=00:00:5f:ff:00:00 eth1addr=00:01:5f:ff:00:01 bootargs=console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw syno_hw_version=DS212j ihd_num=2 netif_num=1 earlyprintk=serial Environment size: 1114/4092 bytes Marvell>> bootm F8080000 F8280000 ## Booting image at f8080000 ... Image Name: Linux-2.6.32.12 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1550968 Bytes = 1.5 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at f8280000 ... Image Name: synology_88f6281_210j 5967 Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 995046 Bytes = 971.7 kB Load Address: 00800000 Entry Point: 00800000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel.
Re: DS210j - flash chip failure and image rebuilding May 03, 2021 05:12PM |
Admin Registered: 13 years ago Posts: 19,114 |