Welcome! Log In Create A New Profile

Advanced

[NSA310S] 2017.07 U-Boot Kirkwood Boot ZyxelOS NAND?

Posted by ianco 
Forum List Message List New Topic
ianco
[NSA310S] 2017.07 U-Boot Kirkwood Boot ZyxelOS NAND?
June 29, 2021 11:44AM
Hello everyone!
Having updated Uboot Stock with 2017.07 U-Boot Kirkwood on Zyxel NSA310S and can safely boot to Debian.
I wanted to try to boot ZyxelOS from Nand using the same parameters as Uboot Stock, but I get stuck on:
""......... done, booting the kernel."
and nothing more.

Do you have any suggestions?

Stock env 
bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
bootcmd=nand read.e 0x2000000 $(kernel_addr) 0xA00000; bootm 0x2000000
bootdelay=2
baudrate=115200
loads_echo=0
ipaddr=10.4.52.165
serverip=10.4.52.7
rootpath=/srv/ubuntu
netmask=255.255.255.0
nandEcc=1bit
kernel_addr=C80000
MODEL_ID=AD03
PRODUCT_NAME=STG-315
FEATURE_BIT=00
CONTRY_TYPE=FF
VENDOR_NAME=MitraStar Technology Corp.
run_diag=yes
ethaddr=28:28:5D:XX:XX:XX


Test 
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:50:06 -0700)
ZyXEL NSA310S/320S 1/2-Bay Power Media Server

SoC:   Kirkwood 88F6702_A1
DRAM:  256 MiB
WARNING: Caches not enabled
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
MV88E1318 PHY initialized on egiga0
Hit any key to stop autoboot:  0 
NSA3x0S> printenv
arcNumber=4931
baudrate=115200
bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; reset
bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootdelay=10
bootdev=usb
console=ttyS0,115200
device=0:1
devices=usb ide
disks=0 1 2 3
dtb_file=/boot/dts/kirkwood-nsa310s.dtb
ethact=egiga0
ethaddr=28:28:5D:XX:XX:XX
if_netconsole=ping $serverip
ipaddr=192.168.0.231
led_error=orange blinking
led_exit=green off
led_init=green blinking
load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file
load_dtb_addr=0x1c00000
load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd
load_initrd_addr=0x1100000
load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage
load_uimage_addr=0x800000
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2)
partition=nand0,2
preboot_nc=run if_netconsole start_netconsole
scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start";  setenv scan_ide "ide reset";  setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done
serverip=192.168.0.220
set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
uenv_addr=0x810000
uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize
uenv_init_devices=setenv init_usb "usb start";  setenv init_ide "ide reset";  setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done;
uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices;  do for disknum in 0; do run uenv_read_disk; done; done;
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read;  fi; else if $devtype part $disknum; then run uenv_read; fi;  fi
usb_ready_retry=15

Environment size: 3010/131068 bytes
NSA3x0S> setenv bootargs console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
NSA3x0S> nand read.e 0x2000000 0xC80000 0xA00000; bootm 0x2000000

NAND read: device 0 offset 0xc80000, size 0xa00000
 10485760 bytes read: OK
## Booting kernel from Legacy Image at 02000000 ...
   Image Name:   Linux-2.6.31.8
   Created:      2017-06-08   3:14:38 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    5957132 Bytes = 5.7 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

Starting kernel ...

Uncompressing Linux................................................................................................................................................................................................................................................................................................ done, booting the kernel.
Reply Quote
bodhi
Re: [NSA310S] 2017.07 U-Boot Kirkwood Boot ZyxelOS NAND?
June 29, 2021 02:58PM
ianco,

I have not tried to investigate this, because stock OS is not good for any thing other than a rescue system.

If you want to have a rescue system on NAND, you could use OpenWrt. The Wiki thread:

https://forum.doozan.com/read.php?2,23630

Quote

Rescue Systems

Rescue System V2 (Original)
MacPlug & SMBPLug
Rescue System Pogo V3
Rescue System V4, using a custom LEDE firmware (BETA)
Rescue System for Pogo E02 using LEDE/OpenWrt (Install with Serial Console)
Rescue System for Pogo V4/Mobile using OpenWrt (Install with NetConsole)

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Reply Quote
ianco
Re: [NSA310S] 2017.07 U-Boot Kirkwood Boot ZyxelOS NAND?
June 29, 2021 04:08PM
Quote
bodhi
I have not tried to investigate this

If you want I can help as a tester to investigate. you tell me what to do and I execute.
in the meantime I tried to set "setenv mainlineLinux no" but nothing has changed.

...meanwhile I would like to report a typing bug that I found in "bootcmd_exec". This bug occurs when NSA310S is booted without USB and HDD: 

U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:50:06 -0700)
ZyXEL NSA310S/320S 1/2-Bay Power Media Server

SoC:   Kirkwood 88F6702_A1
DRAM:  256 MiB
WARNING: Caches not enabled
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
MV88E1318 PHY initialized on egiga0
Hit any key to stop autoboot:  0 
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found

Reset IDE: ide_preinit failed
## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0
loading envs from usb 0 ...
** Bad device usb 0 **

no IDE devices available
running scan_disk ...
Scan device usb
device usb 0:1
** Bad device usb 0 **
device usb 1:1
** Bad device usb 1 **
device usb 2:1
** Bad device usb 2 **
device usb 3:1
** Bad device usb 3 **
Scan device ide

Reset IDE: ide_preinit failed
device ide 0:1
** Bad device ide 0 **
device ide 1:1
** Bad device ide 1 **
device ide 2:1
** Bad device ide 2 **
device ide 3:1
** Bad device ide 3 **
loading uImage ...
** Bad device usb 0 **
loading uInitrd ...
** Bad device usb 0 **
loading DTB /boot/dts/kirkwood-nsa310s.dtb ...
** Bad device usb 0 **
Unknown command 'bootm0x800000' - try 'help'
resetting ...

bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm$load_uimage_addr; fi; fi

renaming: 
bootm$load_uimage_addr
in 
bootm $load_uimage_addr
all solved
Reply Quote
bodhi
Re: [NSA310S] 2017.07 U-Boot Kirkwood Boot ZyxelOS NAND?
June 29, 2021 07:43PM
ianco,

> 
> bootm $load_uimage_addr
>
> all solved

That typo is already on my todo list when I release the next version (it does not effect much since the envs image is installed seperately). But thanks!

ATM, I have no time to look into this stock OS booting subject. It's at the bottom of my priority list of things to do.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Reply Quote
Newer Topic Older Topic
Author:

Your Email:


Subject:
Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: