Hello,
I am hoping someone can help and point me to what could be done to revive my E02 and install debian. So far I have Uboot installed and have been trying to boot off USB to no avail. Here is my printenv. I currently have my serial connection going but I'm unable to make the next step.
arcNumber=3542
bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec
bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootdelay=10
bootdev=usb
device=0:1
device_type=mmc
devices=usb ide mmc
disk_number=3
disks=0 1 2 3
dtb_file=/boot/dts/kirkwood-pogo_e02.dtb
ethact=egiga0
ethaddr=52:3b:20:9c:11:51
if_netconsole=ping $serverip
init_ide=ide reset
init_mmc=mmc rescan
init_usb=usb start
ipaddr=192.168.0.231
led_error=orange blinking
led_exit=green off
led_init=green blinking
load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file
load_dtb_addr=0x1c00000
load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd
load_initrd_addr=0x1100000
load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage
load_uimage_addr=0x800000
machid=dd6
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
partition=nand0,2
preboot_nc=run if_netconsole start_netconsole
scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done
scan_ide=ide reset
scan_mmc=mmc rescan
scan_usb=usb start
serverip=192.168.0.220
set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
uenv_addr=0x810000
uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize
uenv_init_devices=echo Initializing devices...; setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done
uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in $disks; do if test $uenv_loaded -eq 0; then setenv device_type $devtype; setenv disk_number $disknum; run uenv_read; fi; done; done;
uenv_loaded=0
uenv_read=echo Loading envs from $device_type $disk_number...; if load $device_type $disk_number:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; echo ... envs loaded; fi
usb_ready_retry=15
Environment size: 3171/131068 bytes