Trying again to unbrick my stora MS2110
Posted by aaronouthier
|
Re: Trying again to unbrick my stora MS2110 August 14, 2021 09:01PM |
Registered: 3 years ago Posts: 81 |
Yeah, so looking at the Wiki again, I realized step 3 requires me to run dpkg from with stock os in order to create the correct uimage and uninitrd to boot old uboot, since I am on old uboot, but have no bootable OS, I may need to try and flash envs and new uboot from serial console. How safe is this? I realize if I mess up, I have a brick that is bootable ONLY by jtag, but will the system "freak out" if I overwrite uboot while it is running, or is uboot copied to RAM before execution, and run from RAM?
If writing uboot while booted from uboot isn't likely to crash my system, then is it better to attempt writing environment or uboot first?
If writing uboot while booted from uboot isn't likely to crash my system, then is it better to attempt writing environment or uboot first?
|
Re: Trying again to unbrick my stora MS2110 August 14, 2021 10:50PM |
Admin Registered: 13 years ago Posts: 18,545 |
aaronouthier,
> Yeah, so looking at the Wiki again, I realized
> step 3 requires me to run dpkg from with stock os
> in order to create the correct uimage and uninitrd
> to boot old uboot, since I am on old uboot, but
> have no bootable OS
No. You're misread it. run dpkg only when you upgrade kernel.
https://forum.doozan.com/read.php?2,12096
After you booted with the basic rootfs Debian-5.2.9-kirkwood-tld-1-rootfs-bodhi.tar.bz2 successfully, then you have Debian running on USB. Log in and upgrade kernel to the latest.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> Yeah, so looking at the Wiki again, I realized
> step 3 requires me to run dpkg from with stock os
> in order to create the correct uimage and uninitrd
> to boot old uboot, since I am on old uboot, but
> have no bootable OS
No. You're misread it. run dpkg only when you upgrade kernel.
https://forum.doozan.com/read.php?2,12096
Quote
Note: If this is your first time installation, then you only need rootfs Debian-5.2.9-kirkwood-tld-1-rootfs-bodhi.tar.bz2 (this has kernel linux-5.2.9-kirkwood-tld-1 already installed). Please scroll down to 25 Aug 2019 section for download link and installation instruction.
After you booted with the basic rootfs Debian-5.2.9-kirkwood-tld-1-rootfs-bodhi.tar.bz2 successfully, then you have Debian running on USB. Log in and upgrade kernel to the latest.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Trying again to unbrick my stora MS2110 August 15, 2021 04:57AM |
Registered: 3 years ago Posts: 12 |
Hi
Especially for you, I will post a firmware dump later if you are interested in double loading.
https://forum.doozan.com/read.php?3,123779
Especially for you, I will post a firmware dump later if you are interested in double loading.
https://forum.doozan.com/read.php?3,123779
|
Re: Trying again to unbrick my stora MS2110 August 16, 2021 09:04PM |
Registered: 3 years ago Posts: 81 |
Thanks AMD, but I don't need it. I'd rather do this my own way.
Getting stuck after booting:
System hangs here.
What now?
Getting stuck after booting:
## Booting image at 00800000 ... Image Name: Linux-4.12.1-kirkwood-tld-1 Created: 2017-07-20 8:11:24 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3821528 Bytes = 3.6 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 01100000 ... Image Name: initramfs-4.12.1-kirkwood-tld-1 Created: 2017-07-24 0:18:23 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7245632 Bytes = 6.9 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Error: unrecognized/unsupported machine ID (r1 = 0x0000020f). Available machine support: ID (hex) NAME ffffffff Generic DT based system ffffffff Marvell Kirkwood (Flattened Device Tree) Please check your kernel config and/or bootloader.
System hangs here.
What now?
|
Re: Trying again to unbrick my stora MS2110 August 16, 2021 11:52PM |
Admin Registered: 13 years ago Posts: 18,545 |
aaronouthier,
> Getting stuck after booting:
> Uncompressing Linux... done, booting the kernel.
>
> Error: unrecognized/unsupported machine ID (r1 =
> 0x0000020f).
It means you're missing the DTB. If you installed my latest u-boot then the DTB is loaded separately.
If you boot with stock u-boot then the DTB must be embedded inside uImage.
Interrupt serial console and
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> Getting stuck after booting:
> Uncompressing Linux... done, booting the kernel.
>
> Error: unrecognized/unsupported machine ID (r1 =
> 0x0000020f).
It means you're missing the DTB. If you installed my latest u-boot then the DTB is loaded separately.
If you boot with stock u-boot then the DTB must be embedded inside uImage.
Interrupt serial console and
printenv bootPlease post the entire bootlog (don't post excerpt).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Trying again to unbrick my stora MS2110 August 18, 2021 09:22PM |
Registered: 3 years ago Posts: 81 |
This is stock uboot, with the old debian install (I forgot what date, but it was the one mentioned in the wiki for use with stock uboot). Also, I did specify the dtb fie. Unit doesn't autoboot, so I specified the boot commands by hand.
My Stora is powered off at the moment. I will power it up a bit later and post the requested logs/boot transcript and envs.
My Stora is powered off at the moment. I will power it up a bit later and post the requested logs/boot transcript and envs.
|
Re: Trying again to unbrick my stora MS2110 August 18, 2021 10:12PM |
Registered: 3 years ago Posts: 81 |
Bootlog:
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: RD-88F6281A LE
U-Boot 1.1.4 (Sep 4 2009 - 09:36:11) Marvell version: 3.4.14
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CEE60
Soc: 88F6281 A0 (DDR2)
CPU running @ 1000Mhz L2 running @ 333Mhz
SysClock = 333Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 64MB
DRAM CS[1] base 0x04000000 size 64MB
DRAM Total size 128MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB
CRC in Flash: 89e2abae, Calculated CRC: 89e2abae
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
Module 0 is RGMII
Module 1 is TDM
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME], egiga1
USB: scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Trying to load image from USB flash drive using FAT FS
reading /flashware.img
** Unable to read "/flashware.img" from usb 0:1 **
Trying to load image from USB flash drive using ext2 FS partition 0
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - usb 0:0 **
Trying to load image from USB flash drive using ext2 FS partition 1
** Unable to read "/flashware.img" from usb 0:1 **
Couldn't load recovery image from USB flash drive, Trying network interface
Aquiring an IP address using DHCP...
egiga0 no link
egiga1 no link
BOOTP broadcast 1
BOOTP broadcast 2
Abort
egiga0 no link
egiga1 no link
BOOTP broadcast 1
Abort
egiga0 no link
egiga1 no link
BOOTP broadcast 1
Abort
Failed to retreive an IP address assuming default (169.254.100.100)!
Starting the Recovery process to retreive the file...
egiga0 no link
egiga1 no link
uImage load address 0x02000000
Warning: Missing environment variable "deviceName". Assuming default!
Warning: Missing environment variable "modelNumber". Assuming default!
Broadcasting Distress Beacon Packet.
Abort
Failed
Power Button is pressed!
MPP Sel: 00000530, Data IN Enable: 00020058, Data In Polarity: 00000040, Data In: 00000011
Power Button is released!
MAC: 00:01:E8:52:25:5A, IP: 10.82.37.90
egiga0 no link
egiga1 no link
Using egiga0 device
TFTP from server 10.0.0.1; our IP address is 10.82.37.90
Filename 'uImage'.
Load address: 0x800000
Loading: *
Abort
Hit any key to stop autoboot: 0
|
Re: Trying again to unbrick my stora MS2110 August 18, 2021 10:14PM |
Registered: 3 years ago Posts: 81 |
Environment:
Marvell>> printenv baudrate=115200 loads_echo=0 CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_end=:::DB88FXX81:eth0:none ethmtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 nandEcc=1bit netretry=no loadaddr=0x02000000 autoload=no eth1mtu=1500 stdin=serial stdout=serial stderr=serial mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootcmd=tftpboot 0x2000000 $(image_name);setenv bootargs $(console) $(bootargs_root) nfsroot=$(serverip):$(rootpath) ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvNetConfig) $(mvPhoneConfig); bootm 0x2000000; standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; bootdelay=3 disaMvPnp=no eth1addr=00:50:43:00:02:02 hddPowerCtrl=no rcvrip=169.254.100.100 enaAutoRecovery=yes ethaddr=00:01:E8:52:25:5A ipaddr=10.82.37.90 serverip=10.0.0.1 netmask=255.0.0.0 image_name=uImage console=console=ttyS0,115200 bootargs_root=root=/dev/nfs rw rootpath=/mnt/Axentra/marvell.nfs.rootfs/ ethact=egiga0 Environment size: 1277/131068 bytes
|
Re: Trying again to unbrick my stora MS2110 August 18, 2021 10:19PM |
Registered: 3 years ago Posts: 81 |
bodhi Wrote:
-------------------------------------------------------
> aaronouthier,
>
> > Getting stuck after booting:
> > Uncompressing Linux... done, booting the
> kernel.
> >
> > Error: unrecognized/unsupported machine ID (r1
> =
> > 0x0000020f).
>
> It means you're missing the DTB. If you installed
> my latest u-boot then the DTB is loaded
> separately.
>
> If you boot with stock u-boot then the DTB must be
> embedded inside uImage.
>
> Interrupt serial console and
>
>
> excerpt).
I just realized, all of the items you requested are listed in the last post on page 1. The only thing that has changed since then is I removed a few env vars.
-------------------------------------------------------
> aaronouthier,
>
> > Getting stuck after booting:
> > Uncompressing Linux... done, booting the
> kernel.
> >
> > Error: unrecognized/unsupported machine ID (r1
> =
> > 0x0000020f).
>
> It means you're missing the DTB. If you installed
> my latest u-boot then the DTB is loaded
> separately.
>
> If you boot with stock u-boot then the DTB must be
> embedded inside uImage.
>
> Interrupt serial console and
>
>
> printenv > boot >> Please post the entire bootlog (don't post
> excerpt).
I just realized, all of the items you requested are listed in the last post on page 1. The only thing that has changed since then is I removed a few env vars.
|
Re: Trying again to unbrick my stora MS2110 August 19, 2021 01:45AM |
Admin Registered: 13 years ago Posts: 18,545 |
aaronouthier,
> I just realized, all of the items you requested
> are listed in the last post on page 1. The only
> thing that has changed since then is I removed a
> few env vars.
Sure. But the entire boot log in one post will tell the whole story. That'll helps saving time to go back and reread posts. Especially when I'm going back and forth from multiple topics in this forum.
If I can see the boot log with printenvs in serial console, most of the time I can tell what the problem is right away, without asking more questions. We all are in a different time zones, too. It does not work like IRC chat where questions/asnwers happen instantly.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> I just realized, all of the items you requested
> are listed in the last post on page 1. The only
> thing that has changed since then is I removed a
> few env vars.
Sure. But the entire boot log in one post will tell the whole story. That'll helps saving time to go back and reread posts. Especially when I'm going back and forth from multiple topics in this forum.
If I can see the boot log with printenvs in serial console, most of the time I can tell what the problem is right away, without asking more questions. We all are in a different time zones, too. It does not work like IRC chat where questions/asnwers happen instantly.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Trying again to unbrick my stora MS2110 August 19, 2021 07:22AM |
Registered: 3 years ago Posts: 81 |
|
Re: Trying again to unbrick my stora MS2110 August 19, 2021 07:40AM |
Registered: 3 years ago Posts: 81 |
I fixed the inability to load the USB by backing up the stick and reformatting as ext3. I originally used ext4.
The following was from August 14th:
aaronouthier Wrote:
-------------------------------------------------------
> Autoboot is failing with:
>
> Trying to boot manually with:
>
> gives:
>
> Environment is:
>
The following was from August 14th:
aaronouthier Wrote:
-------------------------------------------------------
> Autoboot is failing with:
>
> Hit any key to stop autoboot: 0 > Unknown command 'isL2Prefetch=yes' - try 'help' >>
> Trying to boot manually with:
>
> ext2load usb 0:1 0x1c00000 > /boot/dts/kirkwood-netgear_stora_ms2000.dtb > ext2load usb 0:1 0x1100000 /boot/uInitrd > ext2load usb 0:1 0x800000 /boot/uImage > bootm 0x800000 0x1100000 0x1c00000 >>
> gives:
>
> ## Booting image at 00800000 ... > Image Name: Linux-5.2.9-kirkwood-tld-1 > Created: 2021-03-20 7:34:32 UTC > Image Type: ARM Linux Kernel Image > (uncompressed) > Data Size: 4975115 Bytes = 4.7 MB > Load Address: 00008000 > Entry Point: 00008000 > Verifying Checksum ... OK > OK > ## Loading Ramdisk Image at 01100000 ... > Image Name: initramfs-5.2.9-kirkwood-tld-1 > Created: 2019-08-25 2:22:50 UTC > Image Type: ARM Linux RAMDisk Image (gzip > compressed) > Data Size: 9713872 Bytes = 9.3 MB > Load Address: 00000000 > Entry Point: 00000000 > Verifying Checksum ... OK > > Starting kernel ... > > Uncompressing Linux... done, booting the kernel. > [ 0.000000][ T0] Booting Linux on physical > CPU 0x0 > [ 0.000000][ T0] Linux version > 5.2.9-kirkwood-tld-1 (root@tldDebian) (gcc version > 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 > PREEMPT Sat Aug 17 15:00:56 PDT 2019 > [ 0.000000][ T0] CPU: Feroceon 88FR131 > [56251311] revision 1 (ARMv5TE), cr=0005397f > [ 0.000000][ T0] CPU: VIVT data cache, VIVT > instruction cache > [ 0.000000][ T0] OF: fdt: Machine model: > NETGEAR MS2000 / MS2110 aka Stora > [ 0.000000][ T0] Memory policy: Data cache > writeback > [ 0.000000][ T0] INITRD: > 0x00800000+0x00401000 overlaps in-use memory > region - disabling initrd > [ 0.000000][ T0] Built 1 zonelists, mobility > grouping on. Total pages: 32512 > [ 0.000000][ T0] Kernel command line: > console=ttyS0,115200 ip=off initrd=0x00800040,4M > root=/dev/md0 rw ihd_num=2 netif_num=1 > [ 0.000000][ T0] Dentry cache hash table > entries: 16384 (order: 4, 65536 bytes) > [ 0.000000][ T0] Inode-cache hash table > entries: 8192 (order: 3, 32768 bytes) > [ 0.000000][ T0] Memory: 114320K/131072K > available (9216K kernel code, 868K rwdata, 3400K > rodata, 1024K init, 301K bss, 16752K reserved, 0K > cma-reserved) > [ 0.000000][ T0] random: get_random_u32 > called from cache_alloc_refill+0x38c/0x928 with > crng_init=0 > [ 0.000000][ T0] rcu: Preemptible > hierarchical RCU implementation. > [ 0.000000][ T0] Tasks RCU enabled. > [ 0.000000][ T0] rcu: RCU calculated value > of scheduler-enlistment delay is 10 jiffies. > [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, > preallocated irqs: 16 > [ 0.000000][ T0] clocksource: > orion_clocksource: mask: 0xffffffff max_cycles: > 0xffffffff, max_idle_ns: 9556302233 ns > [ 0.000011][ T0] sched_clock: 32 bits at > 200MHz, resolution 5ns, wraps every 10737418237ns > [ 0.000057][ T0] Switching to timer-based > delay loop, resolution 5ns > [ 0.000949][ T0] Console: colour dummy > device 80x30 > [ 0.001010][ T0] Calibrating delay loop > (skipped), value calculated using timer > frequency.. 400.00 BogoMIPS (lpj=2000000) > [ 0.001042][ T0] pid_max: default: 32768 > minimum: 301 > [ 0.001482][ T0] LSM: Security Framework > initializing > [ 0.001703][ T0] Mount-cache hash table > entries: 1024 (order: 0, 4096 bytes) > [ 0.001735][ T0] Mountpoint-cache hash table > entries: 1024 (order: 0, 4096 bytes) > [ 0.002748][ T0] *** VALIDATE proc *** > [ 0.003058][ T0] *** VALIDATE cgroup1 *** > [ 0.003090][ T0] *** VALIDATE cgroup2 *** > [ 0.003205][ T0] CPU: Testing write buffer > coherency: ok > [ 0.005202][ T1] Setting up static identity > map for 0x100000 - 0x100058 > [ 0.005554][ T1] mvebu-soc-id: MVEBU SoC > ID=0x6281, Rev=0x2 > [ 0.005892][ T1] rcu: Hierarchical SRCU > implementation. > [ 0.009731][ T1] devtmpfs: initialized > [ 0.016660][ T1] clocksource: jiffies: mask: > 0xffffffff max_cycles: 0xffffffff, max_idle_ns: > 19112604462750000 ns > [ 0.016698][ T1] futex hash table entries: > 256 (order: -1, 3072 bytes) > [ 0.016988][ T1] xor: measuring software > checksum speed > [ 0.110135][ T1] arm4regs : 902.400 > MB/sec > [ 0.210092][ T1] 8regs : 542.000 > MB/sec > [ 0.310084][ T1] 32regs : 787.600 > MB/sec > [ 0.310107][ T1] xor: using function: > arm4regs (902.400 MB/sec) > [ 0.310132][ T1] prandom: seed boundary self > test passed > [ 0.315168][ T1] prandom: 100 self tests > passed > [ 0.315182][ T1] pinctrl core: initialized > pinctrl subsystem > [ 0.316919][ T1] NET: Registered protocol > family 16 > [ 0.317664][ T1] DMA: preallocated 256 KiB > pool for atomic coherent allocations > [ 0.318658][ T1] audit: initializing netlink > subsys (disabled) > [ 0.320173][ T14] audit: type=2000 > audit(0.310:1): state=initialized audit_enabled=0 > res=1 > [ 0.320313][ T1] cpuidle: using governor > ladder > [ 0.320405][ T1] cpuidle: using governor > menu > [ 0.321132][ T1] Feroceon L2: Enabling L2 > [ 0.321190][ T1] Feroceon L2: Cache support > initialised. > [ 0.328281][ T1] No ATAGs? > [ 2.560065][ C0] random: fast init done > [ 7.479637][ T71] alg: No test for lzo-rle > (lzo-rle-generic) > [ 7.480274][ T73] alg: No test for lzo-rle > (lzo-rle-scomp) > [ 7.660936][ T1] raid6: int32x8 gen() 106 > MB/s > [ 7.830398][ T1] raid6: int32x8 xor() 72 > MB/s > [ 8.000672][ T1] raid6: int32x4 gen() 108 > MB/s > [ 8.170240][ T1] raid6: int32x4 xor() 69 > MB/s > [ 8.340475][ T1] raid6: int32x2 gen() 110 > MB/s > [ 8.510152][ T1] raid6: int32x2 xor() 78 > MB/s > [ 8.680539][ T1] raid6: int32x1 gen() 83 > MB/s > [ 8.850202][ T1] raid6: int32x1 xor() 57 > MB/s > [ 8.850215][ T1] raid6: using algorithm > int32x2 gen() 110 MB/s > [ 8.850225][ T1] raid6: .... xor() 78 MB/s, > rmw enabled > [ 8.850235][ T1] raid6: using intx1 recovery > algorithm > [ 8.850538][ T1] vgaarb: loaded > [ 8.851159][ T1] SCSI subsystem initialized > [ 8.851773][ T1] usbcore: registered new > interface driver usbfs > [ 8.851850][ T1] usbcore: registered new > interface driver hub > [ 8.851964][ T1] usbcore: registered new > device driver usb > [ 8.852184][ T1] pps_core: LinuxPPS API ver. > 1 registered > [ 8.852198][ T1] pps_core: Software ver. > 5.3.6 - Copyright 2005-2007 Rodolfo Giometti > <giometti@linux.it> > [ 8.852231][ T1] PTP clock support > registered > [ 8.853895][ T1] clocksource: Switched to > clocksource orion_clocksource > [ 10.099017][ T1] VFS: Disk quotas > dquot_6.6.0 > [ 10.099131][ T1] VFS: Dquot-cache hash table > entries: 1024 (order 0, 4096 bytes) > [ 10.111014][ T1] NET: Registered protocol > family 2 > [ 10.112005][ T1] tcp_listen_portaddr_hash > hash table entries: 512 (order: 0, 4096 bytes) > [ 10.112046][ T1] TCP established hash table > entries: 1024 (order: 0, 4096 bytes) > [ 10.112074][ T1] TCP bind hash table > entries: 1024 (order: 0, 4096 bytes) > [ 10.112099][ T1] TCP: Hash tables configured > (established 1024 bind 1024) > [ 10.112218][ T1] UDP hash table entries: 256 > (order: 0, 4096 bytes) > [ 10.112250][ T1] UDP-Lite hash table > entries: 256 (order: 0, 4096 bytes) > [ 10.112521][ T1] NET: Registered protocol > family 1 > [ 10.113299][ T1] RPC: Registered named UNIX > socket transport module. > [ 10.113317][ T1] RPC: Registered udp > transport module. > [ 10.113328][ T1] RPC: Registered tcp > transport module. > [ 10.113338][ T1] RPC: Registered tcp NFSv4.1 > backchannel transport module. > [ 10.113355][ T1] PCI: CLS 0 bytes, default > 32 > [ 10.113994][ T1] NetWinder Floating Point > Emulator V0.97 (double precision) > [ 10.115401][ T1] Initialise system trusted > keyrings > [ 10.115463][ T1] Key type blacklist > registered > [ 10.115734][ T1] workingset: > timestamp_bits=30 max_order=15 bucket_order=0 > [ 10.115874][ T1] zbud: loaded > [ 10.117198][ T1] NFS: Registering the > id_resolver key type > [ 10.117233][ T1] Key type id_resolver > registered > [ 10.117245][ T1] Key type id_legacy > registered > [ 10.117269][ T1] nfs4filelayout_init: NFSv4 > File Layout Driver Registering... > [ 10.117289][ T1] Installing knfsd (copyright > (C) 1996 okir@monad.swb.de). > [ 10.117636][ T1] jffs2: version 2.2. (NAND) > (SUMMARY) © 2001-2006 Red Hat, Inc. > [ 10.117921][ T1] fuse: init (API version > 7.31) > [ 10.118392][ T1] orangefs_debugfs_init: > called with debug mask: :none: :0: > [ 10.118629][ T1] orangefs_init: module > version upstream loaded > [ 10.118644][ T1] SGI XFS with ACLs, security > attributes, realtime, scrub, no debug enabled > [ 10.122390][ T1] async_tx: api initialized > (async) > [ 10.122414][ T1] Key type asymmetric > registered > [ 10.122426][ T1] Asymmetric key parser > 'x509' registered > [ 10.122494][ T1] Block layer SCSI generic > (bsg) driver version 0.4 loaded (major 246) > [ 10.124292][ T1] kirkwood-pinctrl > f1010000.pin-controller: registered pinctrl > driver > [ 10.126612][ T1] mvebu-pcie > mbus@f1000000:pcie@82000000: PCI host bridge to > bus 0000:00 > [ 10.126640][ T1] pci_bus 0000:00: root bus > resource [bus 00-ff] > [ 10.126658][ T1] pci_bus 0000:00: root bus > resource [mem 0xe0000000-0xefffffff] > [ 10.126675][ T1] pci_bus 0000:00: root bus > resource [io 0x1000-0xeffff] > [ 10.126810][ T1] pci 0000:00:01.0: > [11ab:6281] type 01 class 0x060400 > [ 10.126857][ T1] pci 0000:00:01.0: reg 0x38: > [mem 0x00000000-0x000007ff pref] > [ 10.128493][ T1] PCI: bus0: Fast back to > back transfers disabled > [ 10.128526][ T1] pci 0000:00:01.0: bridge > configuration invalid ([bus 00-00]), > reconfiguring > [ 10.130065][ T1] PCI: bus1: Fast back to > back transfers enabled > [ 10.130097][ T1] pci_bus 0000:01: busn_res: > [bus 01-ff] end is updated to 01 > [ 10.130338][ T1] pci 0000:00:01.0: BAR 6: > assigned [mem 0xe0000000-0xe00007ff pref] > [ 10.130360][ T1] pci 0000:00:01.0: PCI > bridge to [bus 01] > [ 10.131097][ T1] mv_xor f1060800.xor: > Marvell shared XOR driver > [ 10.194900][ T1] mv_xor f1060800.xor: > Marvell XOR (Registers Mode): ( xor cpy intr ) > [ 10.197432][ T1] mv_xor f1060900.xor: > Marvell shared XOR driver > [ 10.254925][ T1] mv_xor f1060900.xor: > Marvell XOR (Registers Mode): ( xor cpy intr ) > [ 10.257717][ T1] Serial: 8250/16550 driver, > 2 ports, IRQ sharing disabled > [ 10.259270][ T1] printk: console [ttyS0] > disabled > [ 10.259352][ T1] f1012000.serial: ttyS0 at > MMIO 0xf1012000 (irq = 26, base_baud = 12500000) > is a 16550A > [ 11.097387][ T1] printk: console [ttyS0] > enabled > [ 11.111582][ T1] loop: module loaded > [ 11.116197][ T1] sata_mv f1080000.sata: > slots 32 ports 2 > [ 11.125369][ T1] scsi host0: sata_mv > [ 11.129949][ T1] scsi host1: sata_mv > [ 11.134246][ T1] ata1: SATA max UDMA/133 irq > 33 > [ 11.139069][ T1] ata2: SATA max UDMA/133 irq > 33 > [ 11.145063][ T1] nand: device found, > Manufacturer ID: 0xec, Chip ID: 0xda > [ 11.152209][ T1] nand: Samsung NAND 256MiB > 3,3V 8-bit > [ 11.157650][ T1] nand: 256 MiB, SLC, erase > size: 128 KiB, page size: 2048, OOB size: 64 > [ 11.165999][ T1] Scanning device for bad > blocks > [ 11.228721][ T1] Bad eraseblock 540 at > 0x000004380000 > [ 11.272801][ T1] Bad eraseblock 902 at > 0x0000070c0000 > [ 11.278220][ T1] Bad eraseblock 903 at > 0x0000070e0000 > [ 11.294340][ T1] Bad eraseblock 1004 at > 0x000007d80000 > [ 11.302926][ T1] Bad eraseblock 1034 at > 0x000008140000 > [ 11.308427][ T1] Bad eraseblock 1035 at > 0x000008160000 > [ 11.354827][ T1] Bad eraseblock 1418 at > 0x00000b140000 > [ 11.360312][ T1] Bad eraseblock 1419 at > 0x00000b160000 > [ 11.381317][ T1] Bad eraseblock 1564 at > 0x00000c380000 > [ 11.425741][ T1] Bad eraseblock 1927 at > 0x00000f0e0000 > [ 11.441991][ T1] Bad eraseblock 2028 at > 0x00000fd80000 > [ 11.449534][ T1] 3 fixed-partitions > partitions found on MTD device orion_nand > [ 11.457014][ T1] Creating 3 MTD partitions > on "orion_nand": > [ 11.462913][ T1] > 0x000000000000-0x000000100000 : "u-boot" > [ 11.470279][ T1] > 0x000000100000-0x000000700000 : "uImage" > [ 11.476056][ T112] ata1: SATA link down > (SStatus 0 SControl F300) > [ 11.483881][ T1] > 0x000000700000-0x000010000000 : "root" > [ 11.493692][ T1] libphy: Fixed MDIO Bus: > probed > [ 11.499521][ T1] libphy: orion_mdio_bus: > probed > [ 11.504404][ T1] [Firmware Warn]: > /ocp@f1000000/mdio-bus@72004/ethernet-phy@8: > Whitelisted compatible string. Please remove > [ 11.517092][ T1] mv643xx_eth: MV-643xx > 10/100/1000 ethernet driver version 1.4 > [ 11.525259][ T1] mv643xx_eth_port > mv643xx_eth_port.0: DMA mask not set > [ 11.815573][ T114] ata2: SATA link down > (SStatus 0 SControl F300) > [ 12.244665][ T1] mv643xx_eth_port > mv643xx_eth_port.0 eth0: port 0 with MAC address > 00:01:f1:93:1d:17 > [ 12.254333][ T1] ehci_hcd: USB 2.0 > 'Enhanced' Host Controller (EHCI) Driver > [ 12.261621][ T1] ehci-pci: EHCI PCI platform > driver > [ 12.266893][ T1] ehci-orion: EHCI orion > driver > [ 12.271849][ T1] orion-ehci f1050000.ehci: > EHCI Host Controller > [ 12.278134][ T1] orion-ehci f1050000.ehci: > new USB bus registered, assigned bus number 1 > [ 12.286800][ T1] orion-ehci f1050000.ehci: > irq 30, io mem 0xf1050000 > [ 12.313943][ T1] orion-ehci f1050000.ehci: > USB 2.0 started, EHCI 1.00 > [ 12.321001][ T1] usb usb1: New USB device > found, idVendor=1d6b, idProduct=0002, bcdDevice= > 5.02 > [ 12.330040][ T1] usb usb1: New USB device > strings: Mfr=3, Product=2, SerialNumber=1 > [ 12.338025][ T1] usb usb1: Product: EHCI > Host Controller > [ 12.343633][ T1] usb usb1: Manufacturer: > Linux 5.2.9-kirkwood-tld-1 ehci_hcd > [ 12.351007][ T1] usb usb1: SerialNumber: > f1050000.ehci > [ 12.357185][ T1] hub 1-0:1.0: USB hub found > [ 12.361702][ T1] hub 1-0:1.0: 1 port > detected > [ 12.367238][ T1] usbcore: registered new > interface driver usb-storage > [ 12.374476][ T1] mousedev: PS/2 mouse device > common for all mice > [ 12.733939][ T15] usb 1-1: new high-speed USB > device number 2 using orion-ehci > [ 12.934936][ T15] usb 1-1: New USB device > found, idVendor=0781, idProduct=557d, bcdDevice= > 1.00 > [ 12.943874][ T15] usb 1-1: New USB device > strings: Mfr=1, Product=2, SerialNumber=3 > [ 12.951792][ T15] usb 1-1: Product: Cruzer > Force > [ 12.956639][ T15] usb 1-1: Manufacturer: > SanDisk > [ 12.961453][ T15] usb 1-1: SerialNumber: > 4C530000090703120451 > [ 12.968273][ T15] usb-storage 1-1:1.0: USB > Mass Storage device detected > [ 12.975665][ T15] scsi host2: usb-storage > 1-1:1.0 > [ 13.443953][ T1] rtc-mv f1010300.rtc: > internal RTC not ticking > [ 13.450278][ T1] i2c /dev entries driver > [ 13.461806][ T1] rtc-pcf8563 0-0051: > registered as rtc0 > [ 13.469186][ T1] device-mapper: uevent: > version 1.0.3 > [ 13.474934][ T1] device-mapper: ioctl: > 4.40.0-ioctl (2019-01-18) initialised: > dm-devel@redhat.com > [ 13.484662][ T1] device-mapper: multipath > round-robin: version 1.2.0 loaded > [ 13.491924][ T1] device-mapper: multipath > queue-length: version 0.2.0 loaded > [ 13.499352][ T1] device-mapper: multipath > service-time: version 0.3.0 loaded > [ 13.506839][ T1] device-mapper: > dm-log-userspace: version 1.3.0 loaded > [ 13.513665][ T1] device-mapper: raid: > Loading target version 1.14.0 > [ 13.522298][ T1] hidraw: raw HID events > driver (C) Jiri Kosina > [ 13.528865][ T1] drop_monitor: Initializing > network drop monitor service > [ 13.536268][ T1] NET: Registered protocol > family 17 > [ 13.541721][ T1] Key type dns_resolver > registered > [ 13.547834][ T1] registered taskstats > version 1 > [ 13.552658][ T1] Loading compiled-in X.509 > certificates > [ 13.558296][ T1] zswap: loaded using pool > lzo/zbud > [ 13.581518][ T1] Key type big_key > registered > [ 13.590228][ T1] Key type encrypted > registered > [ 13.598956][ T1] rtc-pcf8563 0-0051: setting > system clock to 2021-08-14T11:36:04 UTC > (1628940964) > [ 13.609338][ T1] md: Waiting for all devices > to be available before autodetect > [ 13.616955][ T1] md: If you don't use raid, > use raid=noautodetect > [ 13.624227][ T1] md: Autodetecting RAID > arrays. > [ 13.629044][ T1] md: autorun ... > [ 13.632548][ T1] md: ... autorun DONE. > [ 13.636984][ T1] EXT4-fs (md0): unable to > read superblock > [ 13.642786][ T1] EXT4-fs (md0): unable to > read superblock > [ 13.650117][ T1] VFS: Cannot open root > device "md0" or unknown-block(9,0): error -5 > [ 13.658233][ T1] Please append a correct > "root=" boot option; here are the available > partitions: > [ 13.667428][ T1] 1f00 1024 > mtdblock0 > [ 13.667433][ T1] (driver?) > [ 13.675612][ T1] 1f01 6144 > mtdblock1 > [ 13.675616][ T1] (driver?) > [ 13.683585][ T1] 1f02 254976 > mtdblock2 > [ 13.683588][ T1] (driver?) > [ 13.691621][ T1] Kernel panic - not syncing: > VFS: Unable to mount root fs on > unknown-block(9,0) > [ 13.700634][ T1] CPU: 0 PID: 1 Comm: swapper > Not tainted 5.2.9-kirkwood-tld-1 #1 > [ 13.708325][ T1] Hardware name: Marvell > Kirkwood (Flattened Device Tree) > [ 13.715349][ T1] [<c010f6ac>] > (unwind_backtrace) from [<c010bb00>] > (show_stack+0x10/0x14) > [ 13.723839][ T1] [<c010bb00>] (show_stack) > from [<c0119fa0>] (panic+0xe0/0x30c) > [ 13.731461][ T1] [<c0119fa0>] (panic) from > [<c0e01628>] (mount_block_root+0x1bc/0x2a4) > [ 13.739686][ T1] [<c0e01628>] > (mount_block_root) from [<c0e017f8>] > (mount_root+0xe8/0x154) > [ 13.748258][ T1] [<c0e017f8>] (mount_root) > from [<c0e019b0>] (prepare_namespace+0x14c/0x18c) > [ 13.757005][ T1] [<c0e019b0>] > (prepare_namespace) from [<c0e011c8>] > (kernel_init_freeable+0x270/0x2dc) > [ 13.766624][ T1] [<c0e011c8>] > (kernel_init_freeable) from [<c09dcee0>] > (kernel_init+0x8/0x10c) > [ 13.775542][ T1] [<c09dcee0>] (kernel_init) > from [<c01010e0>] (ret_from_fork+0x14/0x34) > [ 13.783843][ T1] Exception stack(0xc7881fb0 > to 0xc7881ff8) > [ 13.789618][ T1] 1fa0: > 00000000 00000000 00000000 00000000 > [ 13.798533][ T1] 1fc0: 00000000 00000000 > 00000000 00000000 00000000 00000000 00000000 > 00000000 > [ 13.807452][ T1] 1fe0: 00000000 00000000 > 00000000 00000000 00000013 00000000 > [ 13.814804][ T1] ---[ end Kernel panic - not > syncing: VFS: Unable to mount root fs on > unknown-block(9,0) ]--- >>
> Environment is:
>
> baudrate=115200 > loads_echo=0 > CASset=min > MALLOC_len=1 > ethprime=egiga0 > bootargs_end=:::DB88FXX81:eth0:none > standalone=fsload 0x2000000 $(image_name);setenv > bootargs $(console) root=/dev/mtdblock0 rw > ip=$(ipaddr):$(serverip)$(bootargs_end) > $(mvPhoneConfig); bootm 0x2000000; > ethmtu=1500 > mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs > mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 > usb0Mode=host > yuk_ethaddr=00:00:00:EE:51:81 > nandEcc=1bit > netretry=no > rcvrip=169.254.100.100 > loadaddr=0x02000000 > autoload=no > bootargs=console=ttyS0,115200 ip=off > initrd=0x00800040,4M root=/dev/md0 rw ihd_num=2 > netif_num=1 > eth1addr=00:50:43:00:02:02 > eth1mtu=1500 > usb_set_bootargs=setenv bootargs > console=ttyS0,115200 root=LABEL=rootfs > rootdelay=10 earlyprintk=serial > load_uimage=ext2load usb 0:1 0x800000 > /boot/uImage > load_uinitrd=ext2load usb 0:1 0x2100000 > /boot/uInitrd > usb_boot=mw 0x800000 0 1; run load_uimage; run > load_uinitrd; bootm 0x800000 0x2100000 > usb_bootcmd=run usb_set_bootargs; run usb_boot > bootcmd=usb start; run usb_bootcmd; usb stop; > reset > arcNumber=2743 > stdin=serial > stdout=serial > stderr=serial > mainlineLinux=no > enaMonExt=no > enaCpuStream=no > enaWrAllo=no > pexMode=RC > disL2Cache=no > setL2CacheWT=yes > disL2Prefetch=yes > enaICPref=yes > enaDCPref=yes > sata_dma_mode=yes > netbsd_en=no > vxworks_en=no > bootdelay=3 > disaMvPnp=no > hddPowerCtrl=no > enaAutoRecovery=yes > ethaddr=00:01:E8:BF:D6:4F > ipaddr=10.191.214.79 > serverip=10.0.0.1 > netmask=255.0.0.0 > image_name=uImage > console=console=ttyS0,115200 > bootargs_root=root=/dev/nfs rw > rootpath=/mnt/Axentra/marvell.nfs.rootfs/ > ethact=egiga0 > > Environment size: 1576/131068 bytes >
|
Re: Trying again to unbrick my stora MS2110 August 19, 2021 08:17AM |
Registered: 3 years ago Posts: 81 |
@Bodhi,
Please read my previous post above, in addition to this one.
aaronouthier Wrote:
-------------------------------------------------------
> Bootlog:
>
Please read my previous post above, in addition to this one.
aaronouthier Wrote:
-------------------------------------------------------
> Bootlog:
>
> __ __ _ _ > | \/ | __ _ _ ____ _____| | | > | |\/| |/ _` | '__\ \ / / _ \ | | > | | | | (_| | | \ V / __/ | | > |_| |_|\__,_|_| \_/ \___|_|_| > _ _ ____ _ > | | | | | __ ) ___ ___ | |_ > | | | |___| _ \ / _ \ / _ \| __| > | |_| |___| |_) | (_) | (_) | |_ > \___/ |____/ \___/ \___/ \__| > ** MARVELL BOARD: RD-88F6281A LE > > U-Boot 1.1.4 (Sep 4 2009 - 09:36:11) Marvell > version: 3.4.14 > > U-Boot code: 00600000 -> 0067FFF0 BSS: -> > 006CEE60 > > Soc: 88F6281 A0 (DDR2) > CPU running @ 1000Mhz L2 running @ 333Mhz > SysClock = 333Mhz , TClock = 200Mhz > > DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 > DRAM CS[0] base 0x00000000 size 64MB > DRAM CS[1] base 0x04000000 size 64MB > DRAM Total size 128MB 16bit width > Flash: 0 kB > Addresses 8M - 0M are saved for the U-Boot usage. > Mem malloc Initialization (8M - 7M): Done > NAND:256 MB > CRC in Flash: 89e2abae, Calculated CRC: 89e2abae > > CPU : Marvell Feroceon (Rev 1) > > Streaming disabled > Write allocate disabled > > Module 0 is RGMII > Module 1 is TDM > > USB 0: host mode > PEX 0: interface detected no Link. > Net: egiga0 [PRIME], egiga1 > USB: scanning bus for devices... 2 USB Device(s) > found > scanning bus for storage devices... 1 > Storage Device(s) found > Trying to load image from USB flash drive using > FAT FS > reading /flashware.img > > ** Unable to read "/flashware.img" from usb 0:1 > ** > Trying to load image from USB flash drive using > ext2 FS partition 0 > Failed to mount ext2 filesystem... > ** Bad ext2 partition or disk - usb 0:0 ** > Trying to load image from USB flash drive using > ext2 FS partition 1 > > ** Unable to read "/flashware.img" from usb 0:1 > ** > Couldn't load recovery image from USB flash drive, > Trying network interface > Aquiring an IP address using DHCP... > egiga0 no link > egiga1 no link > BOOTP broadcast 1 > BOOTP broadcast 2 > > Abort > egiga0 no link > egiga1 no link > BOOTP broadcast 1 > > Abort > egiga0 no link > egiga1 no link > BOOTP broadcast 1 > > Abort > Failed to retreive an IP address assuming default > (169.254.100.100)! > Starting the Recovery process to retreive the > file... > egiga0 no link > egiga1 no link > uImage load address 0x02000000 > Warning: Missing environment variable > "deviceName". Assuming default! > Warning: Missing environment variable > "modelNumber". Assuming default! > Broadcasting Distress Beacon Packet. > > Abort > Failed > Power Button is pressed! > MPP Sel: 00000530, Data IN Enable: 00020058, Data > In Polarity: 00000040, Data In: 00000011 > Power Button is released! > MAC: 00:01:E8:52:25:5A, IP: 10.82.37.90 > egiga0 no link > egiga1 no link > Using egiga0 device > TFTP from server 10.0.0.1; our IP address is > 10.82.37.90 > Filename 'uImage'. > Load address: 0x800000 > Loading: * > Abort > Hit any key to stop autoboot: 0 >
Environment: Marvell>> printenv baudrate=115200 loads_echo=0 CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_end=:::DB88FXX81:eth0:none ethmtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 nandEcc=1bit netretry=no loadaddr=0x02000000 autoload=no eth1mtu=1500 stdin=serial stdout=serial stderr=serial mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootcmd=tftpboot 0x2000000 $(image_name);setenv bootargs $(console) $(bootargs_root) nfsroot=$(serverip):$(rootpath) ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvNetConfig) $(mvPhoneConfig); bootm 0x2000000; standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; bootdelay=3 disaMvPnp=no eth1addr=00:50:43:00:02:02 hddPowerCtrl=no rcvrip=169.254.100.100 enaAutoRecovery=yes ethaddr=00:01:E8:52:25:5A ipaddr=10.82.37.90 serverip=10.0.0.1 netmask=255.0.0.0 image_name=uImage console=console=ttyS0,115200 bootargs_root=root=/dev/nfs rw rootpath=/mnt/Axentra/marvell.nfs.rootfs/ ethact=egiga0 Environment size: 1277/131068 bytes
|
Re: Trying again to unbrick my stora MS2110 August 19, 2021 04:01PM |
Admin Registered: 13 years ago Posts: 18,545 |
aaronouthier,
I could not tell if you are running new u-boot or stock u-boot. And if new u-boot, which version?
And did you execute these commands
And then boot?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
I could not tell if you are running new u-boot or stock u-boot. And if new u-boot, which version?
And did you execute these commands
> ext2load usb 0:1 0x1c00000 > /boot/dts/kirkwood-netgear_stora_ms2000.dtb > ext2load usb 0:1 0x1100000 /boot/uInitrd > ext2load usb 0:1 0x800000 /boot/uImage > bootm 0x800000 0x1100000 0x1c00000
And then boot?
boot
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Trying again to unbrick my stora MS2110 August 19, 2021 04:13PM |
Registered: 3 years ago Posts: 81 |
I said in my post last night that I was running stock uBoot. I haven't yet been able to boot to USB, so I can't update uBoot, if I understand correctly.
I never executed just "boot". I used the "bootm" command that you referenced. System hangs, at the aforementioned spot, shortly after bootm command.
I realize you're helping many different folks, in your free time, and without pay. I sometimes start to get frustrated when I mention something, and you don't see it. I have to take a step and remember the first sentence in this paragraph. Perhaps I shouldn't make 4 different posts in a row. Thanks Bodhi, for all you do. I'll get this working someday...
Edited 2 time(s). Last edit at 08/19/2021 04:49PM by aaronouthier.
I never executed just "boot". I used the "bootm" command that you referenced. System hangs, at the aforementioned spot, shortly after bootm command.
I realize you're helping many different folks, in your free time, and without pay. I sometimes start to get frustrated when I mention something, and you don't see it. I have to take a step and remember the first sentence in this paragraph. Perhaps I shouldn't make 4 different posts in a row. Thanks Bodhi, for all you do. I'll get this working someday...
Edited 2 time(s). Last edit at 08/19/2021 04:49PM by aaronouthier.
|
Re: Trying again to unbrick my stora MS2110 August 19, 2021 05:03PM |
Admin Registered: 13 years ago Posts: 18,545 |
aaronouthier,
OK, so booting with stock u-boot needs only uImage and uInitrd. There is no FDT capabilty, so the DTB cannot be loaded and run like with new u-boot.
This error indicated that the uImage does not have the DTB embedded inside.
In the rootfs, you must do Step 4
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
OK, so booting with stock u-boot needs only uImage and uInitrd. There is no FDT capabilty, so the DTB cannot be loaded and run like with new u-boot.
ext2load usb 0:1 0x1100000 /boot/uInitrd ext2load usb 0:1 0x800000 /boot/uImage bootm 0x800000 0x1100000
This error indicated that the uImage does not have the DTB embedded inside.
Quote
Error: unrecognized/unsupported machine ID (r1 = 0x0000020f).
Available machine support:
ID (hex) NAME
ffffffff Generic DT based system
ffffffff Marvell Kirkwood (Flattened Device Tree)
Please check your kernel config and/or bootloader.
In the rootfs, you must do Step 4
Quote
4b. Boot with DTB file embedded in the kernel image.Again, this step 4b is for stock U-Boot only.
Please replace kirkwood-goflexnet.dtb below with the correct DTB name for your box.
Generate the uImage and uInitrd (the kernel files vmlinuz-5.13.6-kirkwood-tld-1 and initrd.img-5.13.6-kirkwood-tld-1 were generated by dpkg in Step 3):
cd /boot
mv uImage uImage.orig
mv uInitrd uInitrd.orig
cp -a zImage-5.13.6-kirkwood-tld-1 zImage.fdt
cat dts/kirkwood-netgear_stora_ms2000.dtb >> zImage.fdt
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n 5.13.6-kirkwood-tld-1 -d zImage.fdt uImage
mkimage -A arm -O linux -T ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n initramfs-5.13.6-kirkwood-tld-1 -d initrd.img-5.13.6-kirkwood-tld-1 uInitrd
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Trying again to unbrick my stora MS2110 August 19, 2021 05:47PM |
Registered: 3 years ago Posts: 81 |
Small issue, but easy to figure out ;p
There was no file called 5.13.6-kirkwood-tld-1 present, so I substituted 4.12.1 for all occurrences of 5.13.6.
I completed the above, however, I now get:
I see the message about not able to open the RTC. I suspect my CR2032 battery is dead. I'll need to replace it. Could that have caused my Kernel Panic?
cd /boot mv uImage uImage.orig mv uInitrd uInitrd.orig cp -a zImage-5.13.6-kirkwood-tld-1 zImage.fdt cat dts/kirkwood-netgear_stora_ms2000.dtb >> zImage.fdt mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n 5.13.6-kirkwood-tld-1 -d zImage.fdt uImage mkimage -A arm -O linux -T ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n initramfs-5.13.6-kirkwood-tld-1 -d initrd.img-5.13.6-kirkwood-tld-1 uInitrd
There was no file called 5.13.6-kirkwood-tld-1 present, so I substituted 4.12.1 for all occurrences of 5.13.6.
I completed the above, however, I now get:
Marvell>> bootm 0x800000 0x1100000 ## Booting image at 00800000 ... Image Name: 4.12.1-kirkwood-tld-1 Created: 2021-08-19 22:29:13 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3833397 Bytes = 3.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 01100000 ... Image Name: initramfs-4.12.1-kirkwood-tld-1 Created: 2021-08-19 22:32:11 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7245632 Bytes = 6.9 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.1-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: NETGEAR MS2000 / MS2110 aka Stora [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlyprintk [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 109436K/131072K available (8192K kernel code, 716K rwdata, 1972K rodata, 1024K init, 288K bss, 21636K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0db3274 ( 717 kB) [ 0.000000] .bss : 0xc0db9b9c - 0xc0e01e60 ( 289 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000009] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.007918] Switching to timer-based delay loop, resolution 5ns [ 0.014433] Console: colour dummy device 80x30 [ 0.019029] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.029648] pid_max: default: 32768 minimum: 301 [ 0.034555] Security Framework initialized [ 0.038915] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.045595] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.053818] CPU: Testing write buffer coherency: ok [ 0.059963] Setting up static identity map for 0x100000 - 0x100058 [ 0.066504] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.075405] devtmpfs: initialized [ 0.083949] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.093935] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.100606] prandom: seed boundary self test passed [ 0.110099] prandom: 100 self tests passed [ 0.114270] pinctrl core: initialized pinctrl subsystem [ 0.120943] NET: Registered protocol family 16 [ 0.125946] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.134792] cpuidle: using governor ladder [ 0.139113] cpuidle: using governor menu [ 0.143538] Feroceon L2: Enabling L2 [ 0.147227] Feroceon L2: Cache support initialised. [ 0.152625] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.169250] No ATAGs? [ 0.180316] vgaarb: loaded [ 0.185816] SCSI subsystem initialized [ 0.190251] usbcore: registered new interface driver usbfs [ 0.195882] usbcore: registered new interface driver hub [ 0.201403] usbcore: registered new device driver usb [ 0.207763] clocksource: Switched to clocksource orion_clocksource [ 0.321887] VFS: Disk quotas dquot_6.6.0 [ 0.325960] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.345644] NET: Registered protocol family 2 [ 0.350974] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.358052] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.364478] TCP: Hash tables configured (established 1024 bind 1024) [ 0.371005] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.376914] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.383471] NET: Registered protocol family 1 [ 0.388403] RPC: Registered named UNIX socket transport module. [ 0.394384] RPC: Registered udp transport module. [ 0.399237] RPC: Registered tcp transport module. [ 0.404008] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.410831] Unpacking initramfs... [ 0.414312] Initramfs unpacking failed: junk in compressed archive [ 0.444381] Freeing initrd memory: 7076K [ 0.448506] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.456171] audit: initializing netlink subsys (disabled) [ 0.462258] Initialise system trusted keyrings [ 0.466817] Key type blacklist registered [ 0.470977] audit: type=2000 audit(0.444:1): state=initialized audit_enabled=0 res=1 [ 0.478976] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 0.485568] zbud: loaded [ 0.489407] NFS: Registering the id_resolver key type [ 0.494536] Key type id_resolver registered [ 0.498857] Key type id_legacy registered [ 0.502951] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.509743] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.516384] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.523786] fuse init (API version 7.26) [ 0.528234] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.535020] orangefs_init: module version upstream loaded [ 0.540516] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 2.567772] random: fast init done [ 7.592287] Key type asymmetric registered [ 7.596457] Asymmetric key parser 'x509' registered [ 7.601788] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 7.609389] io scheduler noop registered [ 7.613381] io scheduler deadline registered [ 7.617873] io scheduler cfq registered (default) [ 7.623923] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 7.641273] loop: module loaded [ 7.646423] libphy: Fixed MDIO Bus: probed [ 7.651554] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.658206] ehci-pci: EHCI PCI platform driver [ 7.662783] ehci-orion: EHCI orion driver [ 7.667094] usbcore: registered new interface driver usb-storage [ 7.673606] mousedev: PS/2 mouse device common for all mice [ 7.679646] i2c /dev entries driver [ 7.683633] kirkwood-cpufreq kirkwood-cpufreq: Unable to get cpuclk [ 7.690068] kirkwood-cpufreq: probe of kirkwood-cpufreq failed with error -22 [ 7.697843] hidraw: raw HID events driver (C) Jiri Kosina [ 7.703709] drop_monitor: Initializing network drop monitor service [ 7.710341] NET: Registered protocol family 17 [ 7.714949] Key type dns_resolver registered [ 7.720142] registered taskstats version 1 [ 7.724310] Loading compiled-in X.509 certificates [ 7.729265] zswap: loaded using pool lzo/zbud [ 7.736554] Key type big_key registered [ 7.742774] Key type encrypted registered [ 7.748532] hctosys: unable to open rtc device (rtc0) [ 8.880306] Unable to handle kernel paging request at virtual address c8000000 [ 8.887591] pgd = c0004000 [ 8.890371] [c8000000] *pgd=00000000 [ 8.894025] Internal error: Oops: 5 [#1] PREEMPT ARM [ 8.899055] Modules linked in: [ 8.902188] CPU: 0 PID: 1 Comm: swapper Not tainted 4.12.1-kirkwood-tld-1 #1 [ 8.909284] Hardware name: Marvell Kirkwood (Flattened Device Tree) [ 8.915610] task: c7832020 task.stack: c7834000 [ 8.920216] PC is at crc32_be+0x6c/0x160 [ 8.924206] LR is at 0xc0950bd0 [ 8.927424] pc : [<c0584814>] lr : [<c0950bd0>] psr: 20000053 [ 8.927424] sp : c7835ef0 ip : c09522dc fp : 00000000 [ 8.939015] r10: c0db9ba0 r9 : c0c4b838 r8 : e3172a00 [ 8.944304] r7 : 00000000 r6 : c7fffffc r5 : 1d3e9e27 r4 : 00000007 [ 8.950888] r3 : e93e3658 r2 : 1e1bdfbc r1 : c115f354 r0 : 8bff03b7 [ 8.957472] Flags: nzCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment none [ 8.964746] Control: 0005397f Table: 00004000 DAC: 00000053 [ 8.970552] Process swapper (pid: 1, stack limit = 0xc7834190) [ 8.976444] Stack: (0xc7835ef0 to 0xc7836000) [ 8.980872] 5ee0: c115f358 f0defde7 3a025302 c0c59544 [ 8.989100] 5f00: 00000000 c0c3f8f0 00000007 c0c3f8bc 000000b8 c010178c 00000000 c01333b0 [ 8.997325] 5f20: 00000000 c0299eec 00000000 c0aeb5e0 000000b8 00000007 00000007 c0aec440 [ 9.005550] 5f40: 000000b7 c0aec440 c7ffced7 00000000 c0d0bc24 00000007 c0c4b830 000000b8 [ 9.013775] 5f60: 00000007 c0c4b834 000000b8 c0c59544 c0db9ba0 c0c00e18 00000007 00000007 [ 9.022000] 5f80: 00000000 c0c005ac 00000000 c08331f8 00000000 00000000 00000000 00000000 [ 9.030225] 5fa0: 00000000 c0833200 00000000 c01070f0 00000000 00000000 00000000 00000000 [ 9.038450] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 9.046676] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000 fdffffff dfdfeffb [ 9.054919] [<c0584814>] (crc32_be) from [<c0c3f8f0>] (of_fdt_raw_init+0x34/0x78) [ 9.062458] [<c0c3f8f0>] (of_fdt_raw_init) from [<c010178c>] (do_one_initcall+0xa8/0x158) [ 9.070692] [<c010178c>] (do_one_initcall) from [<c0c00e18>] (kernel_init_freeable+0x198/0x260) [ 9.079447] [<c0c00e18>] (kernel_init_freeable) from [<c0833200>] (kernel_init+0x8/0x10c) [ 9.087680] [<c0833200>] (kernel_init) from [<c01070f0>] (ret_from_fork+0x14/0x24) [ 9.095303] Code: e1a05002 e59fe0f4 e3550000 0a00002b (e5963004) [ 9.101454] ---[ end trace c9fb935f282424c8 ]--- [ 9.106232] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b [ 9.106232] [ 9.115505] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b [ 9.115505] [ 133.867837] random: crng init done
I see the message about not able to open the RTC. I suspect my CR2032 battery is dead. I'll need to replace it. Could that have caused my Kernel Panic?
|
Re: Trying again to unbrick my stora MS2110 August 19, 2021 08:27PM |
Admin Registered: 13 years ago Posts: 18,545 |
Cool!
Adjust your load addresses to load uInitrd higher:
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Adjust your load addresses to load uInitrd higher:
ext2load usb 0:1 0x2100000 /boot/uInitrd ext2load usb 0:1 0x800000 /boot/uImage bootm 0x800000 0x2100000
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Trying again to unbrick my stora MS2110 August 19, 2021 09:38PM |
Registered: 3 years ago Posts: 81 |
When it rains, it pours.
Still something amiss:
I am noticing the number of bad blocks is increasing!
Still something amiss:
Marvell>> bootm 0x800000 0x2100000 ## Booting image at 00800000 ... Image Name: 4.12.1-kirkwood-tld-1 Created: 2021-08-19 22:29:13 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3833397 Bytes = 3.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 02100000 ... Image Name: initramfs-4.12.1-kirkwood-tld-1 Created: 2021-08-19 22:32:11 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7245632 Bytes = 6.9 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.1-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: NETGEAR MS2000 / MS2110 aka Stora [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlyprintk [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 109420K/131072K available (8192K kernel code, 716K rwdata, 1972K rodata, 1024K init, 288K bss, 21652K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0db3274 ( 717 kB) [ 0.000000] .bss : 0xc0db9b9c - 0xc0e01e60 ( 289 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000009] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.007918] Switching to timer-based delay loop, resolution 5ns [ 0.014433] Console: colour dummy device 80x30 [ 0.019029] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.029648] pid_max: default: 32768 minimum: 301 [ 0.034555] Security Framework initialized [ 0.038915] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.045595] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.053819] CPU: Testing write buffer coherency: ok [ 0.059964] Setting up static identity map for 0x100000 - 0x100058 [ 0.066504] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.075406] devtmpfs: initialized [ 0.083941] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.093924] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.100594] prandom: seed boundary self test passed [ 0.110090] prandom: 100 self tests passed [ 0.114261] pinctrl core: initialized pinctrl subsystem [ 0.120940] NET: Registered protocol family 16 [ 0.125937] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.134773] cpuidle: using governor ladder [ 0.139086] cpuidle: using governor menu [ 0.143513] Feroceon L2: Enabling L2 [ 0.147201] Feroceon L2: Cache support initialised. [ 0.152600] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.169223] No ATAGs? [ 0.180293] vgaarb: loaded [ 0.185792] SCSI subsystem initialized [ 0.190224] usbcore: registered new interface driver usbfs [ 0.195847] usbcore: registered new interface driver hub [ 0.201367] usbcore: registered new device driver usb [ 0.207726] clocksource: Switched to clocksource orion_clocksource [ 0.321843] VFS: Disk quotas dquot_6.6.0 [ 0.325915] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.345613] NET: Registered protocol family 2 [ 0.350949] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.358027] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.364452] TCP: Hash tables configured (established 1024 bind 1024) [ 0.370981] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.376888] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.383447] NET: Registered protocol family 1 [ 0.388378] RPC: Registered named UNIX socket transport module. [ 0.394358] RPC: Registered udp transport module. [ 0.399212] RPC: Registered tcp transport module. [ 0.403982] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.410806] Unpacking initramfs... [ 1.204573] Freeing initrd memory: 7076K [ 1.208746] NetWinder Floating Point Emulator V0.97 (double precision) [ 1.216452] audit: initializing netlink subsys (disabled) [ 1.222531] Initialise system trusted keyrings [ 1.227090] Key type blacklist registered [ 1.231253] audit: type=2000 audit(1.204:1): state=initialized audit_enabled=0 res=1 [ 1.239256] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 1.245846] zbud: loaded [ 1.249683] NFS: Registering the id_resolver key type [ 1.254813] Key type id_resolver registered [ 1.259135] Key type id_legacy registered [ 1.263227] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.270020] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 1.276661] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.284019] fuse init (API version 7.26) [ 1.288468] orangefs_debugfs_init: called with debug mask: :none: :0: [ 1.295251] orangefs_init: module version upstream loaded [ 1.300750] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 2.567735] random: fast init done [ 8.363441] Key type asymmetric registered [ 8.367611] Asymmetric key parser 'x509' registered [ 8.372833] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 8.380421] io scheduler noop registered [ 8.384414] io scheduler deadline registered [ 8.388894] io scheduler cfq registered (default) [ 8.395131] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 8.404776] mvebu-pcie mbus@f1000000:pcie-controller@82000000: PCI host bridge to bus 0000:00 [ 8.413443] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 8.419818] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 8.426757] pci_bus 0000:00: root bus resource [bus 00-ff] [ 8.432716] PCI: bus0: Fast back to back transfers disabled [ 8.438402] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 8.446634] PCI: bus1: Fast back to back transfers enabled [ 8.452290] pci 0000:00:01.0: PCI bridge to [bus 01] [ 8.458002] mv_xor f1060800.xor: Marvell shared XOR driver [ 8.518645] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 8.526513] mv_xor f1060900.xor: Marvell shared XOR driver [ 8.588634] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 8.596755] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 8.604783] console [ttyS0] disabled [ 8.608573] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 8.617617] console [ttyS0] enabled [ 8.617617] console [ttyS0] enabled [ 8.624768] bootconsole [earlycon0] disabled [ 8.624768] bootconsole [earlycon0] disabled [ 8.643784] loop: module loaded [ 8.647608] sata_mv f1080000.sata: slots 32 ports 2 [ 8.655925] scsi host0: sata_mv [ 8.659673] scsi host1: sata_mv [ 8.663107] ata1: SATA max UDMA/133 irq 33 [ 8.667228] ata2: SATA max UDMA/133 irq 33 [ 8.672284] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xda [ 8.678787] nand: Samsung NAND 256MiB 3,3V 8-bit [ 8.683430] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 8.691069] Scanning device for bad blocks [ 8.753283] Bad eraseblock 540 at 0x000004380000 [ 8.796828] Bad eraseblock 902 at 0x0000070c0000 [ 8.801548] Bad eraseblock 903 at 0x0000070e0000 [ 8.816992] Bad eraseblock 1004 at 0x000007d80000 [ 8.824912] Bad eraseblock 1034 at 0x000008140000 [ 8.829713] Bad eraseblock 1035 at 0x000008160000 [ 8.875593] Bad eraseblock 1418 at 0x00000b140000 [ 8.880394] Bad eraseblock 1419 at 0x00000b160000 [ 8.900679] Bad eraseblock 1564 at 0x00000c380000 [ 8.944527] Bad eraseblock 1927 at 0x00000f0e0000 [ 8.960149] Bad eraseblock 2028 at 0x00000fd80000 [ 8.966975] 3 ofpart partitions found on MTD device orion_nand [ 8.972883] Creating 3 MTD partitions on "orion_nand": [ 8.978100] 0x000000000000-0x000000100000 : "u-boot" [ 8.984658] 0x000000100000-0x000000700000 : "uImage" [ 8.991330] 0x000000700000-0x000010000000 : "root" [ 9.001165] libphy: Fixed MDIO Bus: probed [ 9.006359] libphy: orion_mdio_bus: probed [ 9.010554] ata1: SATA link down (SStatus 0 SControl F300) [ 9.016282] [Firmware Warn]: /ocp@f1000000/mdio-bus@72004/ethernet-phy@8: Whitelisted compatible string. Please remove [ 9.032731] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 9.339227] ata2: SATA link down (SStatus 0 SControl F300) [ 10.144407] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:01:e2:d3:7d:d4 [ 10.153324] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 10.159936] ehci-pci: EHCI PCI platform driver [ 10.164465] ehci-orion: EHCI orion driver [ 10.168785] orion-ehci f1050000.ehci: EHCI Host Controller [ 10.174326] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 10.182306] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 10.217770] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 10.224084] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 10.230945] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.238231] usb usb1: Product: EHCI Host Controller [ 10.243133] usb usb1: Manufacturer: Linux 4.12.1-kirkwood-tld-1 ehci_hcd [ 10.249888] usb usb1: SerialNumber: f1050000.ehci [ 10.255377] hub 1-0:1.0: USB hub found [ 10.259261] hub 1-0:1.0: 1 port detected [ 10.263915] usbcore: registered new interface driver usb-storage [ 10.270420] mousedev: PS/2 mouse device common for all mice [ 10.617770] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 10.808691] usb 1-1: New USB device found, idVendor=0781, idProduct=557d [ 10.815444] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 10.822657] usb 1-1: Product: Cruzer Force [ 10.826781] usb 1-1: Manufacturer: SanDisk [ 10.830921] usb 1-1: SerialNumber: 4C530000090703120451 [ 10.837063] usb-storage 1-1:1.0: USB Mass Storage device detected [ 10.843639] scsi host2: usb-storage 1-1:1.0 [ 11.297763] rtc-mv f1010300.rtc: internal RTC not ticking [ 11.303396] i2c /dev entries driver [ 11.310124] rtc-pcf8563 0-0051: low voltage detected, date/time is not reliable. [ 11.317842] rtc-pcf8563 0-0051: rtc core: registered rtc-pcf8563 as rtc0 [ 11.327968] hidraw: raw HID events driver (C) Jiri Kosina [ 11.333872] drop_monitor: Initializing network drop monitor service [ 11.340479] NET: Registered protocol family 17 [ 11.345034] Key type dns_resolver registered [ 11.350260] registered taskstats version 1 [ 11.354381] Loading compiled-in X.509 certificates [ 11.359299] zswap: loaded using pool lzo/zbud [ 11.375450] Key type big_key registered [ 11.390693] Key type encrypted registered [ 11.397678] rtc-pcf8563 0-0051: low voltage detected, date/time is not reliable. [ 11.405300] rtc-pcf8563 0-0051: hctosys: unable to read the hardware clock [ 11.416678] Freeing unused kernel memory: 1024K Loading, please wait... starting version 232 [ 11.861563] scsi 2:0:0:0: Direct-Access SanDisk Cruzer Force 1.00 PQ: 0 ANSI: 6 [ 11.881645] sd 2:0:0:0: [sda] 123174912 512-byte logical blocks: (63.1 GB/58.7 GiB) [ 11.898884] sd 2:0:0:0: [sda] Write Protect is off [ 11.907531] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 11.932037] sda: sda1 [ 11.939500] sd 2:0:0:0: [sda] Attached SCSI removable disk [ 12.000132] usbcore: registered new interface driver uas Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Warning: fsck not present, so skipping unknown file system mount: can't find /root in /etc/fstab done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... mount: mounting /dev on /root/dev failed: No such file or directory mount: mounting /dev on /root/dev failed: No such file or directory done. mount: mounting /run on /root/run failed: No such file or directory run-init: current directory on the same filesystem as the root: error 0 Target filesystem doesn't have requested /sbin/init. run-init: current directory on the same filesystem as the root: error 0 run-init: current directory on the same filesystem as the root: error 0 run-init: current directory on the same filesystem as the root: error 0 run-init: current directory on the same filesystem as the root: error 0 run-init: current directory on the same filesystem as the root: error 0 No init found. Try passing init= bootarg. BusyBox v1.22.1 (Debian 1:1.22.0-19+b3) built-in shell (ash) Enter 'help' for a list of built-in commands. (initramfs) [ 181.777807] random: crng init done
I am noticing the number of bad blocks is increasing!
|
Re: Trying again to unbrick my stora MS2110 August 20, 2021 01:56AM |
Admin Registered: 13 years ago Posts: 18,545 |
aaronouthier,
So the bootargs is incorrect.
Since you are booting with USB now, circle back to the generic instruction I wrote for booting Kirkwood box with stock u-boot (in the Wiki):
https://forum.doozan.com/read.php?2,102054,105374#msg-105374
What you've missed is:
So:
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
So the bootargs is incorrect.
Since you are booting with USB now, circle back to the generic instruction I wrote for booting Kirkwood box with stock u-boot (in the Wiki):
https://forum.doozan.com/read.php?2,102054,105374#msg-105374
setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' setenv load_uinitrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd' setenv usb_boot 'mw 0x800000 0 1; run load_uimage; if run load_uinitrd; then bootm 0x800000 0x2100000; else bootm 0x800000; fi' setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot' setenv bootcmd 'usb start; run usb_bootcmd; usb stop; reset'
What you've missed is:
setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial'
So:
setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' ext2load usb 0:1 0x2100000 /boot/uInitrd ext2load usb 0:1 0x800000 /boot/uImage bootm 0x800000 0x2100000
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Trying again to unbrick my stora MS2110 August 20, 2021 05:54AM |
Registered: 3 years ago Posts: 81 |
Oh!
I'm embarrassed now. This is like the 3rd time that I'm being told to read the instructions better. I actually had those lines in there at one point, but used resetenv a few weeks ago, thinking I had something wrong. I of course then had to chainload AMD's uboot again to fix. I actually do try to figure things out on my own, I swear it.
I'm sure this will come as a complete shock and surprise, but I can be quite silly at times...
I will check this after the sun comes up. It's almost 4 AM here in So. Cal. I'm going back to sleep.
I'm embarrassed now. This is like the 3rd time that I'm being told to read the instructions better. I actually had those lines in there at one point, but used resetenv a few weeks ago, thinking I had something wrong. I of course then had to chainload AMD's uboot again to fix. I actually do try to figure things out on my own, I swear it.
I'm sure this will come as a complete shock and surprise, but I can be quite silly at times...
I will check this after the sun comes up. It's almost 4 AM here in So. Cal. I'm going back to sleep.
|
Re: Trying again to unbrick my stora MS2110 August 20, 2021 06:56AM |
Registered: 3 years ago Posts: 81 |
Well, sleep and I are having a love-hate relationship right now, heh-heh.
I am happy to report that we now have liftoff!
I had to modify 2 of the environment variables, since there is a maximum of 16 arguments per line, and because stock fw's search for flashware.img causes USB to be already started, and USB START borks usb functionality.
Here is what I have:
I am updating the packages on usb system now, and will be rereading the directions before attempting to update uboot and environment.
I am happy to report that we now have liftoff!
I had to modify 2 of the environment variables, since there is a maximum of 16 arguments per line, and because stock fw's search for flashware.img causes USB to be already started, and USB START borks usb functionality.
Here is what I have:
setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' setenv load_uinitrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd' setenv usb_boot 'mw 0x800000 0 1; run load_uimage; run load_uinitrd; bootm 0x800000 0x2100000;' setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot' setenv bootcmd 'run usb_bootcmd; usb stop; reset'
I am updating the packages on usb system now, and will be rereading the directions before attempting to update uboot and environment.
|
Re: Trying again to unbrick my stora MS2110 August 20, 2021 08:10AM |
Registered: 3 years ago Posts: 81 |
Well, all is well that ends well!
uBoot and environment has been flashed, and although it was hinted at, I wasn't explicitly told to move uImage.orig and uInitrd.old to their original names, I realized I should before rebooting! Later on, I'll try updating the rootfs to the latest version.
I also need to find where I put the plastic shell for this thing and try to snap it back together. I hope there weren't any screws involved. It's been months since I disassembled my Stora!
I also need to set the proper eth_addr as listed on the bottom of the unit.
uBoot and environment has been flashed, and although it was hinted at, I wasn't explicitly told to move uImage.orig and uInitrd.old to their original names, I realized I should before rebooting! Later on, I'll try updating the rootfs to the latest version.
I also need to find where I put the plastic shell for this thing and try to snap it back together. I hope there weren't any screws involved. It's been months since I disassembled my Stora!
I also need to set the proper eth_addr as listed on the bottom of the unit.
|
Re: Trying again to unbrick my stora MS2110 August 20, 2021 04:31PM |
Admin Registered: 13 years ago Posts: 18,545 |
aaronouthier,
Congrats!
And thanks for the reminder,
I forgot to revise the instruction to take these into account. This stock u-boot is really ancient. Most of other Kirkwood plugs don't have these problems.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Congrats!
And thanks for the reminder,
and thisQuote
there is a maximum of 16 arguments per line
Quote
USB START borks usb functionality
I forgot to revise the instruction to take these into account. This stock u-boot is really ancient. Most of other Kirkwood plugs don't have these problems.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
