Help reviving my old Iomega IX4-200d

         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** uboot_ver:v1.1.0 **

 ** MARVELL BOARD: IX4-110 LE

U-Boot 1.1.4 (Oct 15 2009 - 17:28:22) Marvell version: 3.4.18

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CF600

Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 256MB
DRAM CS[1] base 0x10000000   size 256MB
DRAM Total size 512MB  16bit width
Found 0x20 i2c device
Toggle power status
Set Power State as Always On
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:32 MB
Found ADT7473, program LED ...(led_volt=90)  OK
Found ADT7473, program thermal/Fan ...(pwm_min=0) (pwm_max=130) (therm=67) (temp_min=60)  OK

Marvell Serial ATA Adapter
Integrated Sata device found


CPU : Marvell Feroceon (Rev 1)
Found initrd at 0x2d4000

Streaming disabled
Write allocate disabled

Module 0 is RGMII
Module 1 is RGMII

USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
SCSI:  AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x7 impl IDE mode
flags: 64bit ncq stag led pmp slum part
scanning bus for devices...
  Device 0: (0:0) Vendor: ATA Prod.: WDC WD6400AAKS-2 Rev: 01.0
            Type: Hard Disk
            Capacity: 610479.3 MB = 596.1 GB (1250261615 x 512)
Net:   egiga0 [PRIME], egiga1
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0xb0000, size 0x224000

Reading data from 0x2d3e00 -- 100% complete.
 2244608 bytes read: OK

NAND read: device 0 offset 0x2d4000, size 0x2f0000

Reading data from 0x301000 --   6% complete.reading NAND page at offset 0x304000 failed
 3080192 bytes read: ERROR
## Booting image at 02000000 ...
   Image Name:   Linux-2.6.22.18
   Created:      2012-01-05  18:29:43 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1910204 Bytes =  1.8 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 12000000 ...
   Image Name:
   Created:      2012-05-02  20:38:45 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    1831340 Bytes =  1.7 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... Bad Data CRC▒

Quote

Updated 26 Sept 2021:

Basic Debian bullseye Kirkwood rootfs for most Kirwood plugs:

Quote

5. Done.

If you are installing on a Kirkwood box that runs stock u-boot (it is not on the new u-boot support list) then see
Boot Kirkwood rootfs with stock u-boot.

Quote

Boot Kirkwood rootfs with stock u-boot

Note: I've updated this instruction to make it more robust (to take into consideration the limitation of much older stock u-boots)

Assuming you have created a USB rootfs following the instruction in the release thread.

Power up, interrupt u-boot count down, and then.

setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial'
setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
setenv load_uinitrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd'
setenv usb_boot 'mw 0x800000 0 1; run load_uimage; run load_uinitrd; bootm 0x800000 0x2100000'
setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot'
setenv bootcmd 'usb reset; run usb_bootcmd; usb stop; reset'

And then,

printenv
saveenv
boot

root@debian:~# uname -a
Linux debian 5.13.6-kirkwood-tld-1 #1.0 PREEMPT Sat Jul 31 22:10:39 PDT 2021 armv5tel GNU/Linux