Help reviving my old Iomega IX4-200d September 07, 2022 09:48AM |
Registered: 1 year ago Posts: 7 |
Re: Help reviving my old Iomega IX4-200d September 07, 2022 03:15PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Help reviving my old Iomega IX4-200d September 08, 2022 02:57AM |
Registered: 1 year ago Posts: 7 |
__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** uboot_ver:v1.1.0 ** ** MARVELL BOARD: IX4-110 LE U-Boot 1.1.4 (Oct 15 2009 - 17:28:22) Marvell version: 3.4.18 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CF600 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM CS[1] base 0x10000000 size 256MB DRAM Total size 512MB 16bit width Found 0x20 i2c device Toggle power status Set Power State as Always On Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:32 MB Found ADT7473, program LED ...(led_volt=90) OK Found ADT7473, program thermal/Fan ...(pwm_min=0) (pwm_max=130) (therm=67) (temp_min=60) OK Marvell Serial ATA Adapter Integrated Sata device found CPU : Marvell Feroceon (Rev 1) Found initrd at 0x2d4000 Streaming disabled Write allocate disabled Module 0 is RGMII Module 1 is RGMII USB 0: host mode PEX 0: PCI Express Root Complex Interface PEX interface detected Link X1 SCSI: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x7 impl IDE mode flags: 64bit ncq stag led pmp slum part scanning bus for devices... Device 0: (0:0) Vendor: ATA Prod.: WDC WD6400AAKS-2 Rev: 01.0 Type: Hard Disk Capacity: 610479.3 MB = 596.1 GB (1250261615 x 512) Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 NAND read: device 0 offset 0xb0000, size 0x224000 Reading data from 0x2d3e00 -- 100% complete. 2244608 bytes read: OK NAND read: device 0 offset 0x2d4000, size 0x2f0000 Reading data from 0x301000 -- 6% complete.reading NAND page at offset 0x304000 failed 3080192 bytes read: ERROR ## Booting image at 02000000 ... Image Name: Linux-2.6.22.18 Created: 2012-01-05 18:29:43 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1910204 Bytes = 1.8 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 12000000 ... Image Name: Created: 2012-05-02 20:38:45 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 1831340 Bytes = 1.7 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... Bad Data CRCâ–’
Re: Help reviving my old Iomega IX4-200d September 08, 2022 04:15PM |
Registered: 2 years ago Posts: 52 |
Re: Help reviving my old Iomega IX4-200d September 08, 2022 05:34PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Help reviving my old Iomega IX4-200d September 09, 2022 01:25AM |
Registered: 1 year ago Posts: 7 |
Re: Help reviving my old Iomega IX4-200d September 09, 2022 04:22AM |
Registered: 2 years ago Posts: 52 |
Re: Help reviving my old Iomega IX4-200d September 09, 2022 03:27PM |
Admin Registered: 13 years ago Posts: 18,821 |
Quote
Updated 26 Sept 2021:
Basic Debian bullseye Kirkwood rootfs for most Kirwood plugs:
Quote
5. Done.
If you are installing on a Kirkwood box that runs stock u-boot (it is not on the new u-boot support list) then see
Boot Kirkwood rootfs with stock u-boot.
Re: Help reviving my old Iomega IX4-200d September 18, 2022 02:08AM |
Registered: 1 year ago Posts: 7 |
Re: Help reviving my old Iomega IX4-200d September 18, 2022 11:27PM |
Admin Registered: 13 years ago Posts: 18,821 |
Quote
Boot Kirkwood rootfs with stock u-boot
Note: I've updated this instruction to make it more robust (to take into consideration the limitation of much older stock u-boots)
Assuming you have created a USB rootfs following the instruction in the release thread.
Power up, interrupt u-boot count down, and then.
setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial'
setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
setenv load_uinitrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd'
setenv usb_boot 'mw 0x800000 0 1; run load_uimage; run load_uinitrd; bootm 0x800000 0x2100000'
setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot'
setenv bootcmd 'usb reset; run usb_bootcmd; usb stop; reset'
And then,
printenv
saveenv
boot
Re: Help reviving my old Iomega IX4-200d September 19, 2022 01:37PM |
Registered: 1 year ago Posts: 7 |
root@debian:~# uname -a Linux debian 5.13.6-kirkwood-tld-1 #1.0 PREEMPT Sat Jul 31 22:10:39 PDT 2021 armv5tel GNU/Linux
Re: Help reviving my old Iomega IX4-200d September 20, 2022 11:12PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Help reviving my old Iomega IX4-200d September 21, 2022 02:32AM |
Registered: 1 year ago Posts: 7 |
Re: Help reviving my old Iomega IX4-200d September 22, 2022 02:45AM |
Admin Registered: 13 years ago Posts: 18,821 |