Welcome! Log In Create A New Profile

Advanced

Bricked DS413J Help needed

Posted by BillyIT 
Forum List Message List New Topic
BillyIT
Bricked DS413J Help needed
February 18, 2023 02:54PM
Hi all,

I don't know if I'm in the good topic.

I have a synology DS413J that bricked maybe from power failure or bad updates.

When I have no disks connected, I have the blinking blue led of death.

I would like to unbrick it and why not install debian on it as there is no more updates of DSM.

Where is the serial port on this model?


Thanks
Reply Quote
Attachments:
open | download - rsz_20230218_211842.jpg (288.3 KB)
open | download - rsz_20230218_211849.jpg (288.5 KB)
daviddyer
Re: Bricked DS413J Help needed
February 18, 2023 10:07PM
https://www.netbsd.org/ports/sandpoint/instSynology.html

For Reference only



Edited 1 time(s). Last edit at 02/18/2023 10:10PM by daviddyer.
Reply Quote
bodhi
Re: Bricked DS413J Help needed
February 18, 2023 11:25PM
daviddyer Wrote:
-------------------------------------------------------
> https://www.netbsd.org/ports/sandpoint/instSynology.html
>
> For Reference only

That's a very good source. Most Synology NAS have the same serial pinout.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Reply Quote
BillyIT
Re: Bricked DS413J Help needed
February 19, 2023 12:47PM
Hi

Thanks

I'm confused because it's not the same on mine. Is it the jp1 with 6pin male or jp2
but only 3pin ? Or jp3 6pin without male connectors. I out pictures about it

Thanks for your help
Reply Quote
bodhi
Re: Bricked DS413J Help needed
February 19, 2023 01:58PM
BillyIT,

I have other Synology models, but not this one. However, they all look similar and heve the same pinout.

It should be "the jp1 with 6pin male". Find the marker for pin 1 (it might not be the triangle, but there should be marker).

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Reply Quote
BillyIT
Re: Bricked DS413J Help needed
February 23, 2023 02:15PM
When i tried the JP1, i don't have anything on putty.

On the picture i put in my first post The mark is on the pin 1
When i put a multimeter on pin2 and a mass point, it beeped
When i put a multimeter on pin 4 and 6, i have 3.xV for the two pins. I read something that there is TX that needs to be about 2.X V and Rx to 0v when not receiving data... Or something like that
Reply Quote
BillyIT
Re: Bricked DS413J Help needed
February 23, 2023 02:41PM
ok my bad, i changed my usb to ttl and don't know the port has changed ! I have my shell !!! youhou... so i need to find what's next now :)
Reply Quote
BillyIT
Re: Bricked DS413J Help needed
February 23, 2023 02:52PM
CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
PEX 1: interface detected no Link.

Synology Model: DS413j
Fan Status: Not Good
Fan 1: Not Good
Fan 2: Not Good

Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
## Booting image at f8090000 ...
Bad Magic Number
Reply Quote
BillyIT
Re: Bricked DS413J Help needed
February 23, 2023 03:56PM 
Marvell>> tftpboot 2000000 zImage
Using egiga0 device
TFTP from server 192.168.10.10; our IP address is 192.168.10.200
Filename 'zImage'.
Load address: 0x2000000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         ############################################
done
Bytes transferred = 1553696 (17b520 hex)
Marvell>> tftpboot  8000000 rd.bin
Using egiga0 device
TFTP from server 192.168.10.10; our IP address is 192.168.10.200
Filename 'rd.bin'.
Load address: 0x8000000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #####################################################
done
Bytes transferred = 3263402 (31cbaa hex)
Marvell>> bootm 0x2000000 0x8000000
## Booting image at 02000000 ...
   Image Name:   Linux-2.6.32.12
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1553632 Bytes =  1.5 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 08000000 ...
   Image Name:   synology_88f6282_413j 25556
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    3263338 Bytes =  3.1 MB
   Load Address: 00800000
   Entry Point:  00800000
   Verifying Checksum ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Linux version 2.6.32.12 (root@build4) (gcc version 4.6.4 (Marvell GCC release 20150204-c4af733b 64K MAXPAGESIZE ALIGN CVE-2015-0235) ) #25556 Thu Mar 4 17:56:48 CST 2021
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: Synology 6282 board
[    0.000000] Using UBoot passing parameters structure
[    0.000000] Sys Clk = 200000000, Tclk = 166666667
[    0.000000] Synology Board ID: 26
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 130048
[    0.000000] Kernel command line: console=ttyS0,115200 ip=off initrd=0x00800040,8M root=/dev/md0 rw syno_hw_version=DS413jv10 ihd_num=4 netif_num=1 flash_size=8
[    0.000000] Synology Hardware Version: DS413jv10-j
[    0.000000] Internal HD num: 4
[    0.000000] Internal netif num: 1
[    0.000000] Flash Memory Size: 8 MB
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 512MB = 512MB total
[    0.000000] Memory: 502784KB available (3656K code, 519K data, 124K init, 0K highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:128
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Calibrating delay loop... 1589.24 BogoMIPS (lpj=7946240)
[    0.240000] Mount-cache hash table entries: 512
[    0.240000] CPU: Testing write buffer coherency: ok
[    0.240000] devtmpfs: initialized
[    0.240000] xor: measuring software checksum speed
[    0.290000]    arm4regs  :  1448.400 MB/sec
[    0.340000]    8regs     :   869.200 MB/sec
[    0.390000]    32regs    :  1122.000 MB/sec
[    0.390000] xor: using function: arm4regs (1448.400 MB/sec)
[    0.390000] NET: Registered protocol family 16
[    0.390000] Feroceon L2: Enabling L2
[    0.390000] Feroceon L2: Cache support initialised, in WT override mode.
[    0.410000]
[    0.410000] CPU Interface
[    0.410000] -------------
[    0.410000] SDRAM_CS0 ....base 00000000, size 512MB
[    0.410000] SDRAM_CS1 ....disable
[    0.410000] SDRAM_CS2 ....disable
[    0.410000] SDRAM_CS3 ....disable
[    0.410000] PEX0_MEM ....base e0000000, size 128MB
[    0.410000] PEX0_IO ....base f2000000, size   1MB
[    0.410000] PEX1_MEM ....base e8000000, size 128MB
[    0.410000] PEX1_IO ....base f2100000, size   1MB
[    0.410000] INTER_REGS ....base f1000000, size   1MB
[    0.410000] NFLASH_CS ....base fa000000, size   2MB
[    0.410000] SPI_CS ....base f4000000, size  16MB
[    0.410000] BOOT_ROM_CS ....no such
[    0.410000] DEV_BOOTCS ....no such
[    0.410000] CRYPT_ENG ....base f0000000, size   2MB
[    0.410000]  Detected Tclk 200000000 and SysClk 533333333
[    0.410000] Apply DS 413j GPIO
[    0.410000] Synology 6282 DS411 GPIO Init
[    0.410000] PCIe link is enable, apply PCIe workaround
[    0.910000] PEX0 interface detected Link X4
[    1.410000] PEX1 interface detected no Link.
[    1.410000] PCI: bus0: Fast back to back transfers disabled
[    1.410000] PCI: bus1: Fast back to back transfers enabled
[    1.420000] bio: create slab <bio-0> at 0
[    1.420000] vgaarb: loaded
[    1.420000] SCSI subsystem initialized
[    1.590000] raid6: int32x1    126 MB/s
[    1.760000] raid6: int32x2    185 MB/s
[    1.930000] raid6: int32x4    180 MB/s
[    2.100000] raid6: int32x8    193 MB/s
[    2.100000] raid6: using algorithm int32x8 (193 MB/s)
[    2.100000] Switching to clocksource kw_clocksource
[    2.100000] NET: Registered protocol family 2
[    2.100000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[    2.100000] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    2.100000] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[    2.100000] TCP: Hash tables configured (established 16384 bind 16384)
[    2.100000] TCP reno registered
[    2.100000] NET: Registered protocol family 1
[    2.100000] RPC: Registered udp transport module.
[    2.100000] RPC: Registered tcp transport module.
[    2.100000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    2.100000] Trying to unpack rootfs image as initramfs...
[    2.100000] Freeing initrd memory: 8192K
[    2.100000] XOR registered 4 channels
[    2.100000] XOR 2nd invalidate WA enabled
[    2.100000] VFS: Disk quotas dquot_6.5.2
[    2.100000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    2.100000] msgmni has been set to 998
[    2.100000] alg: No test for md5 (md5-generic)
[    2.100000] alg: No test for des (des-generic)
[    2.100000] alg: No test for des3_ede (des3_ede-generic)
[    2.100000] alg: No test for stdrng (krng)
[    2.100000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[    2.100000] io scheduler noop registered
[    2.100000] io scheduler anticipatory registered (default)
[    2.110000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    2.110000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[    2.120000] console [ttyS0] enabled
[    2.130000] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[    2.140000] brd: module loaded
[    2.140000] sata_mv 0000:00:01.0: version 1.28
[    2.150000] PCI: enabling device 0000:00:01.0 (0140 -> 0143)
[    2.150000] sata_mv 0000:00:01.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx
[    2.160000] scsi0 : sata_mv
[    2.160000] scsi1 : sata_mv
[    2.170000] scsi2 : sata_mv
[    2.170000] scsi3 : sata_mv
[    2.170000] ata1: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0022000 irq 9
[    2.180000] ata2: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0024000 irq 9
[    2.190000] ata3: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0026000 irq 9
[    2.200000] ata4: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0028000 irq 9
▒
         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** LOADER **
 ** MARVELL BOARD: Synology Disk Station LE

U-Boot 1.1.4 (May 22 2012 - 19:52:31) Marvell version: 3.5.9

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 0068B3D4

Soc: 88F6282 A1CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000   size 512MB
DRAM Total size 512MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Using default environment

[8192kB@f8000000] Flash:  8 MB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
PEX 1: interface detected no Link.

Synology Model: DS413j
Fan Status: Not Good
Fan 1: Not Good
Fan 2: Not Good

Net:   egiga0 [PRIME], egiga1
Hit any key to stop autoboot:  0
## Booting image at f8090000 ...
Bad Magic Number
Marvell>>


I can't succeed for now...
if you can help me have debian, i'm ok with that ! it could be fun !

===========
Moderator edit: please post log in fomartted code



Edited 1 time(s). Last edit at 02/23/2023 04:17PM by bodhi.
Reply Quote
bodhi
Re: Bricked DS413J Help needed
February 23, 2023 04:21PM
Congrats!

Now you can look at the Debian working thread, and post there. I think jhackert completed the Debian boot.

https://forum.doozan.com/read.php?2,132369

Thanks for this too, I forgot to add this box to the kernel support list!

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Reply Quote
BillyIT
Re: Bricked DS413J Help needed
February 24, 2023 04:12AM
Do I need to continue his thread or another one?
Reply Quote
bodhi
Re: Bricked DS413J Help needed
February 24, 2023 02:14PM
Yes. Read the post to see how jhackert booted Debian rootfs:

https://forum.doozan.com/read.php?2,132369

And post in that thread. I think there is still something need to be done. I will help after you can boot into Debian like he did.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Reply Quote
Newer Topic Older Topic
Author:

Subject:
Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: