2023.04 U-Boot Kirkwood - Pogo V4
Posted by bodhi
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 May 24, 2023 06:22PM |
Admin Registered: 13 years ago Posts: 18,545 |
That truncated log is not good!
When you post the good log, please also do this in Debian.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
When you post the good log, please also do this in Debian.
cat /proc/mtd
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 May 24, 2023 06:24PM |
Registered: 1 year ago Posts: 81 |
Here's a non-truncated log of a boot with a USB 2 drive in the top port. I note that there's more error messages ("Bad device specification") when loading envs from usb & sata - but I don't know why.
Edited 1 time(s). Last edit at 05/24/2023 06:29PM by dhargens.
U-Boot 2023.04-tld-1 (May 10 2023 - 23:00:14 -0700)
Pogoplug V4
SoC: Kirkwood 88F6192_A1
Model: Cloud Engines PogoPlug Series 4
DRAM: 128 MiB
Core: 20 devices, 16 uclasses, devicetree: separate
NAND: 128 MiB
MMC: mvsdio@90000: 0
Loading Environment from NAND... OK
In: serial
Out: serial
Err: serial
pcie0.0: Link up
Net: eth0: ethernet-controller@72000
Hit any key to stop autoboot: 0
Initializing devices...
resetting USB...
Bus ehci@50000: USB EHCI 1.00
Bus xhci_pci: Register 400081f NbrPorts 4
Starting the controller
USB XHCI 1.00
scanning bus ehci@50000 for devices... 2 USB Device(s) found
scanning bus xhci_pci for devices... 1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
resetting USB...
Bus ehci@50000: USB EHCI 1.00
Bus xhci_pci: Register 400081f NbrPorts 4
Starting the controller
USB XHCI 1.00
scanning bus ehci@50000 for devices... 2 USB Device(s) found
scanning bus xhci_pci for devices... 1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Loading envs from usb 0...
Failed to load '/boot/uEnv.txt'
Loading envs from usb 1...
** Bad device specification usb 1 **
Couldn't find partition usb 1:1
Can't set block device
Loading envs from usb 2...
** Bad device specification usb 2 **
Couldn't find partition usb 2:1
Can't set block device
Loading envs from usb 3...
** Bad device specification usb 3 **
Couldn't find partition usb 3:1
Can't set block device
Loading envs from sata 0...
** Bad device specification sata 0 **
Couldn't find partition sata 0:1
Can't set block device
Loading envs from sata 1...
** Bad device specification sata 1 **
Couldn't find partition sata 1:1
Can't set block device
Loading envs from sata 2...
** Bad device specification sata 2 **
Couldn't find partition sata 2:1
Can't set block device
Loading envs from sata 3...
** Bad device specification sata 3 **
Couldn't find partition sata 3:1
Can't set block device
running scan_disk ...
Scan device usb
resetting USB...
Bus ehci@50000: USB EHCI 1.00
Bus xhci_pci: Register 400081f NbrPorts 4
Starting the controller
USB XHCI 1.00
scanning bus ehci@50000 for devices... 2 USB Device(s) found
scanning bus xhci_pci for devices... 1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
resetting USB...
Bus ehci@50000: USB EHCI 1.00
Bus xhci_pci: Register 400081f NbrPorts 4
Starting the controller
USB XHCI 1.00
scanning bus ehci@50000 for devices... 2 USB Device(s) found
scanning bus xhci_pci for devices... 1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
device usb 0:1
1 bytes read in 14 ms (0 Bytes/s)
Found bootable drive on usb 0
loading uImage ...
5435888 bytes read in 164 ms (31.6 MiB/s)
loading uInitrd ...
9671860 bytes read in 305 ms (30.2 MiB/s)
loading DTB /boot/dts/kirkwood-pogoplug_v4.dtb ...
9970 bytes read in 19 ms (511.7 KiB/s)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-5.13.6-kirkwood-tld-1
Created: 2021-09-24 0:22:58 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5435824 Bytes = 5.2 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02100000 ...
Image Name: initramfs-5.13.6-kirkwood-tld-1
Created: 2023-05-18 7:19:06 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 9671796 Bytes = 9.2 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01c00000
Booting using the fdt blob at 0x1c00000
Working FDT set to 1c00000
Starting kernel ...
Loading Kernel Image
Loading Ramdisk to 07213000, end 07b4c474 ... OK
Loading Device Tree to 0720d000, end 072126f1 ... OK
Working FDT set to 720d000
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 5.13.6-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 PREEMPT Sat Jul 31 22:10:39 PDT 2021
[ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: Pogoplug v4
[ 0.000000][ T0] Memory policy: Data cache writeback
[ 0.000000][ T0] Zone ranges:
[ 0.000000][ T0] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000][ T0] Movable zone start for each node
[ 0.000000][ T0] Early memory node ranges
[ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 32512
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
[ 0.000000][ T0]
[ 0.000000][ T0] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000][ T0] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000][ T0] Memory: 101108K/131072K available (11264K kernel code, 1553K rwdata, 4272K rodata, 1024K init, 309K bss, 29964K reserved, 0K cma-reserved)
[ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x408/0x7b4 with crng_init=0
[ 0.000000][ T0] trace event string verifier disabled
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] Trampoline variant of Tasks RCU enabled.
[ 0.000000][ T0] Tracing variant of Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[ 0.000003][ T0] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[ 0.000090][ T0] Switching to timer-based delay loop, resolution 6ns
[ 0.001400][ T0] Console: colour dummy device 80x30
[ 0.001514][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666)
[ 0.001581][ T0] pid_max: default: 32768 minimum: 301
[ 0.002195][ T0] LSM: Security Framework initializing
[ 0.002471][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.002546][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.004750][ T0] CPU: Testing write buffer coherency: ok
[ 0.008466][ T1] Setting up static identity map for 0x100000 - 0x100058
[ 0.008934][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[ 0.009453][ T1] rcu: Hierarchical SRCU implementation.
[ 0.011716][ T1] devtmpfs: initialized
[ 0.020056][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.020227][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.076237][ T1] prandom32: self test passed (less than 6 bits correlated)
[ 0.076304][ T1] prandom: seed boundary self test passed
[ 0.082638][ T1] prandom: 100 self tests passed
[ 0.082683][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.085199][ T1] NET: Registered protocol family 16
[ 0.086541][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.088053][ T1] audit: initializing netlink subsys (disabled)
[ 0.090342][ T1] thermal_sys: Registered thermal governor 'step_wise'
[ 0.090902][ T16] audit: type=2000 audit(0.080:1): state=initialized audit_enabled=0 res=1
[ 0.091194][ T1] cpuidle: using governor ladder
[ 0.091340][ T1] cpuidle: using governor menu
[ 0.092121][ T1] Feroceon L2: Enabling L2
[ 0.092199][ T1] Feroceon L2: Cache support initialised.
[ 0.105790][ T1] No ATAGs?
[ 2.560099][ C0] random: fast init done
[ 7.400996][ T39] "cryptomgr_test" (39) uses obsolete ecb(arc4) skcipher
[ 7.440010][ T59] wait_for_initramfs() called before rootfs_initcalls
[ 7.650215][ T1] raid6: int32x8 gen() 74 MB/s
[ 7.820211][ T1] raid6: int32x8 xor() 46 MB/s
[ 7.990381][ T1] raid6: int32x4 gen() 76 MB/s
[ 8.160195][ T1] raid6: int32x4 xor() 49 MB/s
[ 8.330213][ T1] raid6: int32x2 gen() 98 MB/s
[ 8.500174][ T1] raid6: int32x2 xor() 60 MB/s
[ 8.670138][ T1] raid6: int32x1 gen() 75 MB/s
[ 8.840243][ T1] raid6: int32x1 xor() 43 MB/s
[ 8.840270][ T1] raid6: using algorithm int32x2 gen() 98 MB/s
[ 8.840290][ T1] raid6: .... xor() 60 MB/s, rmw enabled
[ 8.840308][ T1] raid6: using intx1 recovery algorithm
[ 8.840723][ T1] vgaarb: loaded
[ 8.841567][ T1] SCSI subsystem initialized
[ 8.842346][ T1] usbcore: registered new interface driver usbfs
[ 8.842453][ T1] usbcore: registered new interface driver hub
[ 8.842536][ T1] usbcore: registered new device driver usb
[ 8.842866][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 8.842890][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 8.842941][ T1] PTP clock support registered
[ 8.845680][ T1] clocksource: Switched to clocksource orion_clocksource
[ 8.996718][ T1] VFS: Disk quotas dquot_6.6.0
[ 8.996880][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 9.019790][ T1] NET: Registered protocol family 2
[ 9.020039][ T1] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 9.021457][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 9.021534][ T1] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 9.021585][ T1] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 9.021628][ T1] TCP: Hash tables configured (established 1024 bind 1024)
[ 9.022018][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 9.022134][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 9.022198][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 9.022545][ T1] NET: Registered protocol family 1
[ 9.036301][ T1] RPC: Registered named UNIX socket transport module.
[ 9.036337][ T1] RPC: Registered udp transport module.
[ 9.036356][ T1] RPC: Registered tcp transport module.
[ 9.036373][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 9.036400][ T1] PCI: CLS 0 bytes, default 32
[ 9.036669][ T1] NetWinder Floating Point Emulator V0.97 (double precision)
[ 9.037560][ T58] Trying to unpack rootfs image as initramfs...
[ 11.617856][ T58] Freeing initrd memory: 9448K
[ 12.557207][ T1] Initialise system trusted keyrings
[ 12.557323][ T1] Key type blacklist registered
[ 12.557713][ T1] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[ 12.557898][ T1] zbud: loaded
[ 12.560158][ T1] NFS: Registering the id_resolver key type
[ 12.560220][ T1] Key type id_resolver registered
[ 12.560243][ T1] Key type id_legacy registered
[ 12.560310][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 12.560346][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 12.560368][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 12.560783][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 12.561617][ T1] fuse: init (API version 7.34)
[ 12.562219][ T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 12.562553][ T1] orangefs_init: module version upstream loaded
[ 12.562583][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled
[ 12.715321][ T1] xor: measuring software checksum speed
[ 12.728689][ T1] arm4regs : 746 MB/sec
[ 12.750806][ T1] 8regs : 447 MB/sec
[ 12.766035][ T1] 32regs : 651 MB/sec
[ 12.766061][ T1] xor: using function: arm4regs (746 MB/sec)
[ 12.766095][ T1] async_tx: api initialized (async)
[ 12.766126][ T1] Key type asymmetric registered
[ 12.766145][ T1] Asymmetric key parser 'x509' registered
[ 12.766238][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[ 12.766356][ T1] io scheduler bfq registered
[ 13.063800][ T1] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 47
[ 13.063846][ T1] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 49
[ 13.064424][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 13.067370][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges:
[ 13.067506][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000
[ 13.067574][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 13.067624][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 13.068063][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00
[ 13.068099][ T1] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 13.068137][ T1] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff])
[ 13.068170][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[ 13.068199][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 13.068381][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400
[ 13.068440][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[ 13.070149][ T1] PCI: bus0: Fast back to back transfers disabled
[ 13.070204][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 13.070563][ T1] pci 0000:01:00.0: [1b73:1009] type 00 class 0x0c0330
[ 13.070624][ T1] pci 0000:01:00.0: reg 0x10: [mem 0x90000000-0x9000ffff 64bit]
[ 13.070672][ T1] pci 0000:01:00.0: reg 0x18: [mem 0x90010000-0x90010fff 64bit]
[ 13.070718][ T1] pci 0000:01:00.0: reg 0x20: [mem 0x90011000-0x90011fff 64bit]
[ 13.070856][ T1] pci 0000:01:00.0: supports D1
[ 13.070883][ T1] pci 0000:01:00.0: PME# supported from D0 D1 D3hot
[ 13.070999][ T1] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 13.097056][ T1] PCI: bus1: Fast back to back transfers disabled
[ 13.097107][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 13.097432][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff]
[ 13.097476][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0100000-0xe01007ff pref]
[ 13.097518][ T1] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff 64bit]
[ 13.097564][ T1] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0010000-0xe0010fff 64bit]
[ 13.097608][ T1] pci 0000:01:00.0: BAR 4: assigned [mem 0xe0011000-0xe0011fff 64bit]
[ 13.097652][ T1] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 13.097685][ T1] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff]
[ 13.097874][ T1] pcieport 0000:00:01.0: enabling device (0140 -> 0142)
[ 13.098816][ T1] mv_xor f1060800.xor: Marvell shared XOR driver
[ 13.157361][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 13.161328][ T1] mv_xor f1060900.xor: Marvell shared XOR driver
[ 13.227350][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 13.231736][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 13.233860][ T1] printk: console [ttyS0] disabled
[ 13.234007][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 10416666) is a 16550A
[ 14.334660][ T1] printk: console [ttyS0] enabled
[ 14.352732][ T1] loop: module loaded
[ 14.357849][ T1] sata_mv f1080000.sata: slots 32 ports 2
[ 14.369143][ T1] scsi host0: sata_mv
[ 14.373979][ T1] scsi host1: sata_mv
[ 14.378315][ T1] ata1: SATA max UDMA/133 irq 32
[ 14.383114][ T1] ata2: SATA max UDMA/133 irq 32
[ 14.389747][ T1] Could not find a valid ONFI parameter page, trying bit-wise majority to recover it
[ 14.399157][ T1] ONFI parameter recovery failed, aborting
[ 14.404810][ T1] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[ 14.411866][ T1] nand: Hynix NAND 128MiB 3,3V 8-bit
[ 14.417021][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 14.425742][ T1] Scanning device for bad blocks
[ 14.531700][ T1] 5 cmdlinepart partitions found on MTD device orion_nand
[ 14.538678][ T1] Creating 5 MTD partitions on "orion_nand":
[ 14.544503][ T1] 0x000000000000-0x000000200000 : "u-boot"
[ 14.552460][ T1] 0x000000200000-0x000000500000 : "uImage"
[ 14.560264][ T1] 0x000000500000-0x000000800000 : "uImage2"
[ 14.568122][ T1] 0x000000800000-0x000001000000 : "failsafe"
[ 14.576119][ T1] 0x000001000000-0x000008000000 : "root"
[ 14.585248][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 14.593824][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 14.606064][ T1] libphy: Fixed MDIO Bus: probed
[ 14.613132][ T1] libphy: orion_mdio_bus: probed
[ 14.642672][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 14.716353][ T94] ata1: SATA link down (SStatus 0 SControl F300)
[ 15.057480][ T96] ata2: SATA link down (SStatus 0 SControl F300)
[ 15.407173][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:04:0d:95
[ 15.416831][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 15.424077][ T1] ehci-pci: EHCI PCI platform driver
[ 15.429334][ T1] ehci-orion: EHCI orion driver
[ 15.434346][ T1] orion-ehci f1050000.ehci: EHCI Host Controller
[ 15.440605][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 15.449234][ T1] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
[ 15.485717][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 15.492836][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13
[ 15.501825][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 15.509754][ T1] usb usb1: Product: EHCI Host Controller
[ 15.515317][ T1] usb usb1: Manufacturer: Linux 5.13.6-kirkwood-tld-1 ehci_hcd
[ 15.522722][ T1] usb usb1: SerialNumber: f1050000.ehci
[ 15.529174][ T1] hub 1-0:1.0: USB hub found
[ 15.533697][ T1] hub 1-0:1.0: 1 port detected
[ 15.539714][ T1] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 15.545656][ T1] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[ 15.555588][ T1] xhci_hcd 0000:01:00.0: hcc params 0x200073a1 hci version 0x100 quirks 0x0000000000080010
[ 15.566485][ T1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13
[ 15.575435][ T1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 15.583371][ T1] usb usb2: Product: xHCI Host Controller
[ 15.588965][ T1] usb usb2: Manufacturer: Linux 5.13.6-kirkwood-tld-1 xhci-hcd
[ 15.596368][ T1] usb usb2: SerialNumber: 0000:01:00.0
[ 15.602622][ T1] hub 2-0:1.0: USB hub found
[ 15.607224][ T1] hub 2-0:1.0: 2 ports detected
[ 15.612912][ T1] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 15.618949][ T1] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3
[ 15.627105][ T1] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed
[ 15.634185][ T1] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 15.643466][ T1] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.13
[ 15.652445][ T1] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 15.660375][ T1] usb usb3: Product: xHCI Host Controller
[ 15.665963][ T1] usb usb3: Manufacturer: Linux 5.13.6-kirkwood-tld-1 xhci-hcd
[ 15.673342][ T1] usb usb3: SerialNumber: 0000:01:00.0
[ 15.679800][ T1] hub 3-0:1.0: USB hub found
[ 15.684305][ T1] hub 3-0:1.0: 2 ports detected
[ 15.690461][ T1] usbcore: registered new interface driver usb-storage
[ 15.697916][ T1] mousedev: PS/2 mouse device common for all mice
[ 15.825728][ T17] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 16.026865][ T17] usb 1-1: New USB device found, idVendor=0781, idProduct=5571, bcdDevice= 1.00
[ 16.035771][ T17] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 16.043624][ T17] usb 1-1: Product: Cruzer Fit
[ 16.048268][ T17] usb 1-1: Manufacturer: SanDisk'
[ 16.053140][ T17] usb 1-1: SerialNumber: 03022114021123185139
[ 16.060179][ T17] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 16.067931][ T17] scsi host2: usb-storage 1-1:1.0
[ 16.725732][ T1] rtc-mv f1010300.rtc: internal RTC not ticking
[ 16.732092][ T1] i2c /dev entries driver
[ 16.737262][ T1] device-mapper: uevent: version 1.0.3
[ 16.742974][ T1] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com
[ 16.752801][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 16.760105][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 16.767441][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 16.774828][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 16.781638][ T1] device-mapper: raid: Loading target version 1.15.1
[ 16.790265][ T1] hid: raw HID events driver (C) Jiri Kosina
[ 16.796635][ T1] drop_monitor: Initializing network drop monitor service
[ 16.804270][ T1] NET: Registered protocol family 10
[ 16.811551][ T1] Segment Routing with IPv6
[ 16.816041][ T1] RPL Segment Routing with IPv6
[ 16.820872][ T1] NET: Registered protocol family 17
[ 16.826378][ T1] Key type dns_resolver registered
[ 16.832191][ T1] registered taskstats version 1
[ 16.837099][ T1] Loading compiled-in X.509 certificates
[ 16.843241][ T1] zswap: loaded using pool lzo/zbud
[ 16.848911][ T1] Key type ._fscrypt registered
[ 16.853618][ T1] Key type .fscrypt registered
[ 16.858326][ T1] Key type fscrypt-provisioning registered
[ 16.867614][ T1] Key type big_key registered
[ 16.917095][ T1] Key type encrypted registered
[ 16.931446][ T1] Freeing unused kernel memory: 1024K
[ 16.956998][ T1] Checked W+X mappings: passed, no W+X pages found
[ 16.963365][ T1] Run /init as init process
Loading, please wait...
[ 17.127523][ T58] scsi 2:0:0:0: Direct-Access SanDisk' Cruzer Fit 1.00 PQ: 0 ANSI: 6
[ 17.147579][ T7] sd 2:0:0:0: [sda] 30031872 512-byte logical blocks: (15.4 GB/14.3 GiB)
[ 17.167457][ T7] sd 2:0:0:0: [sda] Write Protect is off
[ 17.185834][ T7] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Starting version 247.3-7+deb11u2
[ 17.213056][ T7] sda: sda1
[ 17.222434][ T7] sd 2:0:0:0: [sda] Attached SCSI removable disk
[ 18.352939][ T144] input: gpio_keys as /devices/platform/gpio_keys/input/input0
[ 18.669805][ T144] usbcore: registered new interface driver uas
[ 18.826333][ T7] mvsdio f1090000.mvsdio: Got CD GPIO
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.36.1
[/sbin/fsck.ext4 (1) -- /dev/sda1] fsck.ext4 -a -C0 /dev/sda1
rootfs: clean, 18138/940240 files, 395278/3753728 blocks
done.
[ 29.729582][ T168] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
[ 30.731406][ T1] systemd[1]: System time before build time, advancing clock.
[ 30.812176][ T1] systemd[1]: Inserted module 'autofs4'
[ 30.908481][ T1] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified)
[ 30.933554][ T1] systemd[1]: Detected architecture arm.
Welcome to Debian GNU/Linux 11 (bullseye)!
[ 30.978364][ T1] systemd[1]: Set hostname to <deb01>.
[ 33.545338][ T1] systemd[1]: Queued start job for default target Graphical Interface.
[ 33.557548][ T1] random: systemd: uninitialized urandom read (16 bytes read)
[ 33.565344][ T1] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling.
[ 33.578551][ T1] systemd[1]: (This warning is only shown for the first unit using IP firewalling.)
[ 33.590655][ T1] systemd[1]: Created slice system-getty.slice.
[ OK ] Created slice system-getty.slice.
[ 33.626136][ T1] random: systemd: uninitialized urandom read (16 bytes read)
[ 33.635199][ T1] systemd[1]: Created slice system-modprobe.slice.
[ OK ] Created slice system-modprobe.slice.
[ 33.676129][ T1] random: systemd: uninitialized urandom read (16 bytes read)
[ 33.685136][ T1] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ OK ] Created slice system-serial\x2dgetty.slice.
[ 33.727435][ T1] systemd[1]: Created slice User and Session Slice.
[ OK ] Created slice User and Session Slice.
[ 33.766913][ T1] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ OK ] Started Dispatch Password …ts to Console Directory Watch.
[ 33.806776][ T1] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ OK ] Started Forward Password R…uests to Wall Directory Watch.
[ 33.848128][ T1] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ OK ] Set up automount Arbitrary…s File System Automount Point.
[ 33.886672][ T1] systemd[1]: Reached target Local Encrypted Volumes.
[ OK ] Reached target Local Encrypted Volumes.
[ 33.927020][ T1] systemd[1]: Reached target Paths.
[ OK ] Reached target Paths.
[ 33.966658][ T1] systemd[1]: Reached target Slices.
[ OK ] Reached target Slices.
[ 34.009268][ T1] systemd[1]: Listening on RPCbind Server Activation Socket.
[ OK ] Listening on RPCbind Server Activation Socket.
[ 34.047450][ T1] systemd[1]: Listening on fsck to fsckd communication Socket.
[ OK ] Listening on fsck to fsckd communication Socket.
[ 34.086884][ T1] systemd[1]: Listening on initctl Compatibility Named Pipe.
[ OK ] Listening on initctl Compatibility Named Pipe.
[ 34.128114][ T1] systemd[1]: Listening on Journal Audit Socket.
[ OK ] Listening on Journal Audit Socket.
[ 34.167489][ T1] systemd[1]: Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket (/dev/log).
[ 34.207737][ T1] systemd[1]: Listening on Journal Socket.
[ OK ] Listening on Journal Socket.
[ 34.248546][ T1] systemd[1]: Listening on udev Control Socket.
[ OK ] Listening on udev Control Socket.
[ 34.287430][ T1] systemd[1]: Listening on udev Kernel Socket.
[ OK ] Listening on udev Kernel Socket.
[ 34.328069][ T1] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
[ 34.344141][ T1] systemd[1]: Mounting POSIX Message Queue File System...
Mounting POSIX Message Queue File System...
[ 34.391897][ T1] systemd[1]: Mounting NFSD configuration filesystem...
Mounting NFSD configuration filesystem...
[ 34.442338][ T1] systemd[1]: Mounting RPC Pipe File System...
Mounting RPC Pipe File System...
[ 34.493387][ T1] systemd[1]: Mounting Kernel Debug File System...
Mounting Kernel Debug File System...
[ 34.543247][ T1] systemd[1]: Mounting Kernel Trace File System...
Mounting Kernel Trace File System...
[ 34.586450][ T1] systemd[1]: Condition check resulted in Kernel Module supporting RPCSEC_GSS being skipped.
[ 34.606688][ T1] systemd[1]: Starting Restore / save the current clock...
Starting Restore / save the current clock...
[ 34.654786][ T1] systemd[1]: Starting Create list of static device nodes for the current kernel...
Starting Create list of st…odes for the current kernel...
[ 34.710735][ T1] systemd[1]: Starting Load Kernel Module configfs...
Starting Load Kernel Module configfs...
[ 34.783991][ T1] systemd[1]: Starting Load Kernel Module drm...
Starting Load Kernel Module drm...
[ 34.833874][ T1] systemd[1]: Starting Load Kernel Module fuse...
Starting Load Kernel Module fuse...
[ 34.880389][ C0] random: crng init done
[ 34.884512][ C0] random: 7 urandom warning(s) missed due to ratelimiting
[ 34.898337][ T1] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[ 34.908869][ T1] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[ 34.926715][ T1] systemd[1]: Starting Journal Service...
Starting Journal Service...
[ 34.966962][ T1] systemd[1]: Starting Load Kernel Modules...
Starting Load Kernel Modules...
[ 35.007884][ T1] systemd[1]: Starting Remount Root and Kernel File Systems...
Starting Remount Root and Kernel File Systems...
[ 35.083272][ T1] systemd[1]: Starting Coldplug All udev Devices...
Starting Coldplug All udev Devices...
[ 35.260974][ T1] systemd[1]: Mounted POSIX Message Queue File System.
[ OK ] Mounted POSIX Message Queue File System.
[ 35.337360][ T1] systemd[1]: Mounted NFSD configuration filesystem.
[ OK ] Mounted NFSD configuration filesystem.
[ 35.384304][ T1] systemd[1]: Mounted RPC Pipe File System.
[ OK ] Mounted RPC Pipe File System.
[ 35.447970][ T1] systemd[1]: Mounted Kernel Debug File System.
[ OK ] Mounted Kernel Debug File System.
[ 35.463330][ T1] systemd[1]: Mounted Kernel Trace File System.
[ OK ] Mounted Kernel Trace File System.
[ 35.539222][ T1] systemd[1]: Finished Restore / save the current clock.
[ OK ] Finished Restore / save the current clock.
[ 35.586243][ T1] systemd[1]: Finished Create list of static device nodes for the current kernel.
[ 35.605992][ T214] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro. Quota mode: none.
[ OK ] Finished Create list of st… nodes for the current kernel.
[ 35.689838][ T1] systemd[1]: modprobe@configfs.service: Succeeded.
[ 35.726230][ T1] systemd[1]: Finished Load Kernel Module configfs.
[ OK ] Finished Load Kernel Module configfs.
[ 35.749611][ T1] systemd[1]: modprobe@drm.service: Succeeded.
[ 35.786243][ T1] systemd[1]: Finished Load Kernel Module drm.
[ OK ] Finished Load Kernel Module drm.
[ 35.809646][ T1] systemd[1]: modprobe@fuse.service: Succeeded.
[ 35.834347][ T1] systemd[1]: Finished Load Kernel Module fuse.
[ OK ] Finished Load Kernel Module fuse.
[ 35.896220][ T1] systemd[1]: Finished Load Kernel Modules.
[ OK ] Finished Load Kernel Modules.
[ 35.939218][ T1] systemd[1]: Finished Remount Root and Kernel File Systems.
[ OK ] Finished Remount Root and Kernel File Systems.
[ 36.026816][ T1] systemd[1]: Activating swap /swapfile1...
Activating swap /swapfile1...
[ 36.106575][ T1] systemd[1]: Mounting FUSE Control File System...
Mounting FUSE Control File System...
[ 36.185872][ T218] Adding 524284k swap on /swapfile1. Priority:-2 extents:3 across:540668k FS
[ 36.266287][ T1] systemd[1]: Mounting Kernel Configuration File System...
Mounting Kernel Configuration File System...
[ 36.327206][ T1] systemd[1]: Starting pNFS block layout mapping daemon...
Starting pNFS block layout mapping daemon...
[ 36.369291][ T1] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[ 36.397252][ T1] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
[ 36.457950][ T1] systemd[1]: Starting Load/Save Random Seed...
Starting Load/Save Random Seed...
[ 36.507698][ T1] systemd[1]: Starting Apply Kernel Variables...
Starting Apply Kernel Variables...
[ 36.577933][ T1] systemd[1]: Starting Create System Users...
Starting Create System Users...
[ 36.620382][ T1] systemd[1]: Activated swap /swapfile1.
[ OK ] Activated swap /swapfile1.
[ 36.739056][ T1] systemd[1]: Started Journal Service.
[ OK ] Started Journal Service.
[ OK ] Mounted FUSE Control File System.
[ OK ] Mounted Kernel Configuration File System.
[ OK ] Started pNFS block layout mapping daemon.
[ OK ] Finished Load/Save Random Seed.
[ OK ] Finished Apply Kernel Variables.
[ OK ] Reached target Swap.
Starting Flush Journal to Persistent Storage...
[ OK ] Finished Create System Users.
Starting Create Static Device Nodes in /dev...
[ 37.400501][ T210] systemd-journald[210]: Received client request to flush runtime journal.
[ OK ] Finished Coldplug All udev Devices.
[ 37.442075][ T210] systemd-journald[210]: File /var/log/journal/c4334d5b2fba8bce5294b56551baee86/system.journal corrupted or uncleanly shut down, renaming and replacing.
Starting Helper to synchronize boot up for ifupdown...
[ OK ] Finished Create Static Device Nodes in /dev.
[ OK ] Reached target Local File Systems (Pre).
[ OK ] Reached target Local File Systems.
Starting Preprocess NFS configuration...
Starting Rule-based Manage…for Device Events and Files...
[ OK ] Finished Preprocess NFS configuration.
Starting NFSv4 ID-name mapping service...
[ OK ] Reached target NFS client services.
[ OK ] Started NFSv4 ID-name mapping service.
[ OK ] Finished Flush Journal to Persistent Storage.
Starting Create Volatile Files and Directories...
[ OK ] Started Rule-based Manager for Device Events and Files.
[ OK ] Finished Create Volatile Files and Directories.
Starting RPC bind portmap service...
Starting Update UTMP about System Boot/Shutdown...
[ OK ] Started RPC bind portmap service.
[ OK ] Reached target RPC Port Mapper.
[ OK ] Finished Update UTMP about System Boot/Shutdown.
[ OK ] Reached target System Initialization.
[ OK ] Started Daily apt download activities.
[ OK ] Started Daily apt upgrade and clean activities.
[ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems.
[ OK ] Started Daily man-db regeneration.
[ OK ] Started Update the plocate database daily.
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Reached target Timers.
[ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
Starting Avahi mDNS/DNS-SD Stack...
[ OK ] Started D-Bus System Message Bus.
Starting Remove Stale Onli…t4 Metadata Check Snapshots...
Starting User Login Management...
[ OK ] Started Avahi mDNS/DNS-SD Stack.
[ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots.
[ OK ] Started User Login Management.
[ OK ] Found device /dev/ttyS0.
[ 41.449703][ T255] orion_wdt: Initial timeout 25 sec
[ 42.229063][ T255] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 42.311508][ T238] marvell-cesa f1030000.crypto: CESA device successfully registered
[* ] A start job is running for Helper t…oot up for ifupdown (9s / 3min 3s)
[ OK ] Finished Helper to synchronize boot up for ifupdown.
Starting Raise network interfaces...
[** ] A start job is running for Raise network interfaces (12s / 5min 9s)
[*** ] A start job is running for Raise network interfaces (12s / 5min 9s)
[ *** ] A start job is running for Raise network interfaces (13s / 5min 9s)
[ *** ] A start job is running for Raise network interfaces (13s / 5min 9s)
[ 47.435141][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 47.445747][ T100] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ ***] A start job is running for Raise network interfaces (14s / 5min 9s)
[ **] A start job is running for Raise network interfaces (14s / 5min 9s)
[ *] A start job is running for Raise network interfaces (15s / 5min 9s)
[ **] A start job is running for Raise network interfaces (15s / 5min 9s)
[ ***] A start job is running for Raise network interfaces (15s / 5min 9s)
[ OK ] Finished Raise network interfaces.
[ OK ] Reached target Network.
Starting NFS Mount Daemon...
Starting Network Time Service...
Starting /etc/rc.local Compatibility...
Starting OpenBSD Secure Shell server...
[ OK ] Started NFS Mount Daemon.
Starting NFS server and services...
[ OK ] Started Network Time Service.
[ OK ] Started /etc/rc.local Compatibility.
[ OK ] Started OpenBSD Secure Shell server.
[ 51.811436][ T383] NFSD: Using UMH upcall client tracking operations.
[ 51.818180][ T383] NFSD: starting 90-second grace period (net f000001c)
[ OK ] Finished NFS server and services.
[ OK ] Reached target Remote File Systems (Pre).
[ OK ] Reached target Remote File Systems.
Starting LSB: Starts syslogd...
Starting Permit User Sessions...
[ OK ] Finished Permit User Sessions.
[ OK ] Started Getty on tty1.
[ OK ] Started Serial Getty on ttyS0.
[ OK ] Reached target Login Prompts.
[ OK ] Started LSB: Starts syslogd.
Starting LSB: Starts klogd...
[ OK ] Started LSB: Starts klogd.
[ OK ] Reached target Multi-User System.
[ OK ] Reached target Graphical Interface.
Starting Update UTMP about System Runlevel Changes...
[ OK ] Finished Update UTMP about System Runlevel Changes.
Debian GNU/Linux 11 deb01 ttyS0
deb01 login:
Edited 1 time(s). Last edit at 05/24/2023 06:29PM by dhargens.
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 May 24, 2023 06:28PM |
Registered: 1 year ago Posts: 81 |
And here's a non-truncated boot from the rear port using a USB 3 drive. It too has errors in the same place as above.
U-Boot 2023.04-tld-1 (May 10 2023 - 23:00:14 -0700)
Pogoplug V4
SoC: Kirkwood 88F6192_A1
Model: Cloud Engines PogoPlug Series 4
DRAM: 128 MiB
Core: 20 devices, 16 uclasses, devicetree: separate
NAND: 128 MiB
MMC: mvsdio@90000: 0
Loading Environment from NAND... OK
In: serial
Out: serial
Err: serial
pcie0.0: Link up
Net: eth0: ethernet-controller@72000
Hit any key to stop autoboot: 0
Initializing devices...
resetting USB...
Bus ehci@50000: USB EHCI 1.00
Bus xhci_pci: Register 400081f NbrPorts 4
Starting the controller
USB XHCI 1.00
scanning bus ehci@50000 for devices... 1 USB Device(s) found
scanning bus xhci_pci for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
resetting USB...
Bus ehci@50000: USB EHCI 1.00
Bus xhci_pci: Register 400081f NbrPorts 4
Starting the controller
USB XHCI 1.00
scanning bus ehci@50000 for devices... 1 USB Device(s) found
scanning bus xhci_pci for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Loading envs from usb 0...
Failed to load '/boot/uEnv.txt'
Loading envs from usb 1...
** Bad device specification usb 1 **
Couldn't find partition usb 1:1
Can't set block device
Loading envs from usb 2...
** Bad device specification usb 2 **
Couldn't find partition usb 2:1
Can't set block device
Loading envs from usb 3...
** Bad device specification usb 3 **
Couldn't find partition usb 3:1
Can't set block device
Loading envs from sata 0...
** Bad device specification sata 0 **
Couldn't find partition sata 0:1
Can't set block device
Loading envs from sata 1...
** Bad device specification sata 1 **
Couldn't find partition sata 1:1
Can't set block device
Loading envs from sata 2...
** Bad device specification sata 2 **
Couldn't find partition sata 2:1
Can't set block device
Loading envs from sata 3...
** Bad device specification sata 3 **
Couldn't find partition sata 3:1
Can't set block device
running scan_disk ...
Scan device usb
resetting USB...
Bus ehci@50000: USB EHCI 1.00
Bus xhci_pci: Register 400081f NbrPorts 4
Starting the controller
USB XHCI 1.00
scanning bus ehci@50000 for devices... 1 USB Device(s) found
scanning bus xhci_pci for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
resetting USB...
Bus ehci@50000: USB EHCI 1.00
Bus xhci_pci: Register 400081f NbrPorts 4
Starting the controller
USB XHCI 1.00
scanning bus ehci@50000 for devices... 1 USB Device(s) found
scanning bus xhci_pci for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
device usb 0:1
1 bytes read in 20 ms (0 Bytes/s)
Found bootable drive on usb 0
loading uImage ...
5435888 bytes read in 129 ms (40.2 MiB/s)
loading uInitrd ...
9672174 bytes read in 128 ms (72.1 MiB/s)
loading DTB /boot/dts/kirkwood-pogoplug_v4.dtb ...
9970 bytes read in 27 ms (360.4 KiB/s)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-5.13.6-kirkwood-tld-1
Created: 2021-09-24 0:22:58 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5435824 Bytes = 5.2 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02100000 ...
Image Name: initramfs-5.13.6-kirkwood-tld-1
Created: 2023-03-31 2:14:18 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 9672110 Bytes = 9.2 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01c00000
Booting using the fdt blob at 0x1c00000
Working FDT set to 1c00000
Starting kernel ...
Loading Kernel Image
Loading Ramdisk to 07213000, end 07b4c5ae ... OK
Loading Device Tree to 0720d000, end 072126f1 ... OK
Working FDT set to 720d000
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 5.13.6-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 PREEMPT Sat Jul 31 22:10:39 PDT 2021
[ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: Pogoplug v4
[ 0.000000][ T0] Memory policy: Data cache writeback
[ 0.000000][ T0] Zone ranges:
[ 0.000000][ T0] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000][ T0] Movable zone start for each node
[ 0.000000][ T0] Early memory node ranges
[ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 32512
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
[ 0.000000][ T0]
[ 0.000000][ T0] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000][ T0] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000][ T0] Memory: 101108K/131072K available (11264K kernel code, 1553K rwdata, 4272K rodata, 1024K init, 309K bss, 29964K reserved, 0K cma-reserved)
[ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x408/0x7b4 with crng_init=0
[ 0.000000][ T0] trace event string verifier disabled
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] Trampoline variant of Tasks RCU enabled.
[ 0.000000][ T0] Tracing variant of Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[ 0.000003][ T0] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[ 0.000090][ T0] Switching to timer-based delay loop, resolution 6ns
[ 0.001401][ T0] Console: colour dummy device 80x30
[ 0.001515][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666)
[ 0.001582][ T0] pid_max: default: 32768 minimum: 301
[ 0.002195][ T0] LSM: Security Framework initializing
[ 0.002471][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.002546][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.004750][ T0] CPU: Testing write buffer coherency: ok
[ 0.008467][ T1] Setting up static identity map for 0x100000 - 0x100058
[ 0.008935][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[ 0.009453][ T1] rcu: Hierarchical SRCU implementation.
[ 0.011723][ T1] devtmpfs: initialized
[ 0.020046][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.020215][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.076232][ T1] prandom32: self test passed (less than 6 bits correlated)
[ 0.076302][ T1] prandom: seed boundary self test passed
[ 0.082636][ T1] prandom: 100 self tests passed
[ 0.082683][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.085195][ T1] NET: Registered protocol family 16
[ 0.086537][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.088053][ T1] audit: initializing netlink subsys (disabled)
[ 0.090359][ T1] thermal_sys: Registered thermal governor 'step_wise'
[ 0.090923][ T16] audit: type=2000 audit(0.080:1): state=initialized audit_enabled=0 res=1
[ 0.091216][ T1] cpuidle: using governor ladder
[ 0.091368][ T1] cpuidle: using governor menu
[ 0.092148][ T1] Feroceon L2: Enabling L2
[ 0.092226][ T1] Feroceon L2: Cache support initialised.
[ 0.105818][ T1] No ATAGs?
[ 2.560099][ C0] random: fast init done
[ 7.400975][ T39] "cryptomgr_test" (39) uses obsolete ecb(arc4) skcipher
[ 7.439978][ T59] wait_for_initramfs() called before rootfs_initcalls
[ 7.650326][ T1] raid6: int32x8 gen() 74 MB/s
[ 7.820258][ T1] raid6: int32x8 xor() 46 MB/s
[ 7.990411][ T1] raid6: int32x4 gen() 76 MB/s
[ 8.160143][ T1] raid6: int32x4 xor() 49 MB/s
[ 8.330333][ T1] raid6: int32x2 gen() 99 MB/s
[ 8.500144][ T1] raid6: int32x2 xor() 60 MB/s
[ 8.670395][ T1] raid6: int32x1 gen() 75 MB/s
[ 8.840273][ T1] raid6: int32x1 xor() 42 MB/s
[ 8.840299][ T1] raid6: using algorithm int32x2 gen() 99 MB/s
[ 8.840320][ T1] raid6: .... xor() 60 MB/s, rmw enabled
[ 8.840337][ T1] raid6: using intx1 recovery algorithm
[ 8.840755][ T1] vgaarb: loaded
[ 8.841600][ T1] SCSI subsystem initialized
[ 8.842390][ T1] usbcore: registered new interface driver usbfs
[ 8.842498][ T1] usbcore: registered new interface driver hub
[ 8.842584][ T1] usbcore: registered new device driver usb
[ 8.842916][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 8.842940][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 8.842992][ T1] PTP clock support registered
[ 8.845736][ T1] clocksource: Switched to clocksource orion_clocksource
[ 8.996774][ T1] VFS: Disk quotas dquot_6.6.0
[ 8.996933][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 9.019653][ T1] NET: Registered protocol family 2
[ 9.019902][ T1] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 9.021317][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 9.021393][ T1] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 9.021445][ T1] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 9.021488][ T1] TCP: Hash tables configured (established 1024 bind 1024)
[ 9.021880][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 9.021993][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 9.022056][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 9.022402][ T1] NET: Registered protocol family 1
[ 9.036360][ T1] RPC: Registered named UNIX socket transport module.
[ 9.036396][ T1] RPC: Registered udp transport module.
[ 9.036415][ T1] RPC: Registered tcp transport module.
[ 9.036432][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 9.036459][ T1] PCI: CLS 0 bytes, default 32
[ 9.036726][ T1] NetWinder Floating Point Emulator V0.97 (double precision)
[ 9.037617][ T58] Trying to unpack rootfs image as initramfs...
[ 11.619056][ T58] Freeing initrd memory: 9448K
[ 12.558486][ T1] Initialise system trusted keyrings
[ 12.558589][ T1] Key type blacklist registered
[ 12.558981][ T1] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[ 12.559169][ T1] zbud: loaded
[ 12.561425][ T1] NFS: Registering the id_resolver key type
[ 12.561487][ T1] Key type id_resolver registered
[ 12.561510][ T1] Key type id_legacy registered
[ 12.561578][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 12.561615][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 12.561639][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 12.562052][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 12.562887][ T1] fuse: init (API version 7.34)
[ 12.563496][ T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 12.563834][ T1] orangefs_init: module version upstream loaded
[ 12.563864][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled
[ 12.715372][ T1] xor: measuring software checksum speed
[ 12.728742][ T1] arm4regs : 746 MB/sec
[ 12.750860][ T1] 8regs : 447 MB/sec
[ 12.766088][ T1] 32regs : 651 MB/sec
[ 12.766114][ T1] xor: using function: arm4regs (746 MB/sec)
[ 12.766149][ T1] async_tx: api initialized (async)
[ 12.766180][ T1] Key type asymmetric registered
[ 12.766200][ T1] Asymmetric key parser 'x509' registered
[ 12.766293][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[ 12.766412][ T1] io scheduler bfq registered
[ 13.063922][ T1] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 47
[ 13.063970][ T1] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 49
[ 13.064551][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 13.067505][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges:
[ 13.067639][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000
[ 13.067708][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 13.067759][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 13.068197][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00
[ 13.068234][ T1] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 13.068270][ T1] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff])
[ 13.068303][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[ 13.068332][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 13.068511][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400
[ 13.068571][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[ 13.070277][ T1] PCI: bus0: Fast back to back transfers disabled
[ 13.070332][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 13.070692][ T1] pci 0000:01:00.0: [1b73:1009] type 00 class 0x0c0330
[ 13.070752][ T1] pci 0000:01:00.0: reg 0x10: [mem 0x90000000-0x9000ffff 64bit]
[ 13.070801][ T1] pci 0000:01:00.0: reg 0x18: [mem 0x90010000-0x90010fff 64bit]
[ 13.070846][ T1] pci 0000:01:00.0: reg 0x20: [mem 0x90011000-0x90011fff 64bit]
[ 13.070985][ T1] pci 0000:01:00.0: supports D1
[ 13.071013][ T1] pci 0000:01:00.0: PME# supported from D0 D1 D3hot
[ 13.071127][ T1] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 13.097112][ T1] PCI: bus1: Fast back to back transfers disabled
[ 13.097162][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 13.097488][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff]
[ 13.097532][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0100000-0xe01007ff pref]
[ 13.097574][ T1] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff 64bit]
[ 13.097621][ T1] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0010000-0xe0010fff 64bit]
[ 13.097665][ T1] pci 0000:01:00.0: BAR 4: assigned [mem 0xe0011000-0xe0011fff 64bit]
[ 13.097709][ T1] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 13.097741][ T1] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff]
[ 13.097927][ T1] pcieport 0000:00:01.0: enabling device (0140 -> 0142)
[ 13.098878][ T1] mv_xor f1060800.xor: Marvell shared XOR driver
[ 13.157414][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 13.161395][ T1] mv_xor f1060900.xor: Marvell shared XOR driver
[ 13.227401][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 13.231805][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 13.233926][ T1] printk: console [ttyS0] disabled
[ 13.234074][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 10416666) is a 16550A
[ 14.334669][ T1] printk: console [ttyS0] enabled
[ 14.352720][ T1] loop: module loaded
[ 14.357844][ T1] sata_mv f1080000.sata: slots 32 ports 2
[ 14.369134][ T1] scsi host0: sata_mv
[ 14.373964][ T1] scsi host1: sata_mv
[ 14.378303][ T1] ata1: SATA max UDMA/133 irq 32
[ 14.383095][ T1] ata2: SATA max UDMA/133 irq 32
[ 14.389738][ T1] Could not find a valid ONFI parameter page, trying bit-wise majority to recover it
[ 14.399156][ T1] ONFI parameter recovery failed, aborting
[ 14.404818][ T1] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[ 14.411874][ T1] nand: Hynix NAND 128MiB 3,3V 8-bit
[ 14.417028][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 14.425718][ T1] Scanning device for bad blocks
[ 14.531709][ T1] 5 cmdlinepart partitions found on MTD device orion_nand
[ 14.538685][ T1] Creating 5 MTD partitions on "orion_nand":
[ 14.544512][ T1] 0x000000000000-0x000000200000 : "u-boot"
[ 14.552471][ T1] 0x000000200000-0x000000500000 : "uImage"
[ 14.560271][ T1] 0x000000500000-0x000000800000 : "uImage2"
[ 14.568150][ T1] 0x000000800000-0x000001000000 : "failsafe"
[ 14.576139][ T1] 0x000001000000-0x000008000000 : "root"
[ 14.585244][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 14.593815][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 14.606049][ T1] libphy: Fixed MDIO Bus: probed
[ 14.613121][ T1] libphy: orion_mdio_bus: probed
[ 14.642591][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 14.716269][ T94] ata1: SATA link down (SStatus 0 SControl F300)
[ 15.057538][ T96] ata2: SATA link down (SStatus 0 SControl F300)
[ 15.407248][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:04:0d:95
[ 15.416906][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 15.424152][ T1] ehci-pci: EHCI PCI platform driver
[ 15.429402][ T1] ehci-orion: EHCI orion driver
[ 15.434415][ T1] orion-ehci f1050000.ehci: EHCI Host Controller
[ 15.440672][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 15.449302][ T1] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
[ 15.485770][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 15.492872][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13
[ 15.501857][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 15.509787][ T1] usb usb1: Product: EHCI Host Controller
[ 15.515350][ T1] usb usb1: Manufacturer: Linux 5.13.6-kirkwood-tld-1 ehci_hcd
[ 15.522754][ T1] usb usb1: SerialNumber: f1050000.ehci
[ 15.529201][ T1] hub 1-0:1.0: USB hub found
[ 15.533720][ T1] hub 1-0:1.0: 1 port detected
[ 15.539734][ T1] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 15.545671][ T1] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[ 15.555586][ T1] xhci_hcd 0000:01:00.0: hcc params 0x200073a1 hci version 0x100 quirks 0x0000000000080010
[ 15.566720][ T1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13
[ 15.575667][ T1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 15.583605][ T1] usb usb2: Product: xHCI Host Controller
[ 15.589197][ T1] usb usb2: Manufacturer: Linux 5.13.6-kirkwood-tld-1 xhci-hcd
[ 15.596600][ T1] usb usb2: SerialNumber: 0000:01:00.0
[ 15.602854][ T1] hub 2-0:1.0: USB hub found
[ 15.607453][ T1] hub 2-0:1.0: 2 ports detected
[ 15.613129][ T1] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 15.619173][ T1] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3
[ 15.627323][ T1] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed
[ 15.634401][ T1] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 15.643674][ T1] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.13
[ 15.652659][ T1] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 15.660617][ T1] usb usb3: Product: xHCI Host Controller
[ 15.666204][ T1] usb usb3: Manufacturer: Linux 5.13.6-kirkwood-tld-1 xhci-hcd
[ 15.673583][ T1] usb usb3: SerialNumber: 0000:01:00.0
[ 15.679866][ T1] hub 3-0:1.0: USB hub found
[ 15.684371][ T1] hub 3-0:1.0: 2 ports detected
[ 15.690344][ T1] usbcore: registered new interface driver usb-storage
[ 15.697687][ T1] mousedev: PS/2 mouse device common for all mice
[ 15.975889][ T17] usb 3-1: new SuperSpeed USB device number 2 using xhci_hcd
[ 16.007366][ T17] usb 3-1: New USB device found, idVendor=0781, idProduct=5583, bcdDevice= 1.00
[ 16.016264][ T17] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 16.024082][ T17] usb 3-1: Product: SanDisk 3.2Gen1
[ 16.029241][ T17] usb 3-1: Manufacturer: USB
[ 16.033767][ T17] usb 3-1: SerialNumber: 0501c10c74b9c1541ce43b9a0ebe975b7003f71eec568210b28326f8f998dae4b85000000000000000000000c0caed5e0009071083558107162f1bf4
[ 16.054414][ T17] usb-storage 3-1:1.0: USB Mass Storage device detected
[ 16.062140][ T17] scsi host2: usb-storage 3-1:1.0
[ 16.725787][ T1] rtc-mv f1010300.rtc: internal RTC not ticking
[ 16.732145][ T1] i2c /dev entries driver
[ 16.737313][ T1] device-mapper: uevent: version 1.0.3
[ 16.743035][ T1] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com
[ 16.752855][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 16.760155][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 16.767490][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 16.774869][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 16.781670][ T1] device-mapper: raid: Loading target version 1.15.1
[ 16.790311][ T1] hid: raw HID events driver (C) Jiri Kosina
[ 16.796680][ T1] drop_monitor: Initializing network drop monitor service
[ 16.804349][ T1] NET: Registered protocol family 10
[ 16.811621][ T1] Segment Routing with IPv6
[ 16.816116][ T1] RPL Segment Routing with IPv6
[ 16.820951][ T1] NET: Registered protocol family 17
[ 16.826458][ T1] Key type dns_resolver registered
[ 16.832251][ T1] registered taskstats version 1
[ 16.837156][ T1] Loading compiled-in X.509 certificates
[ 16.843304][ T1] zswap: loaded using pool lzo/zbud
[ 16.849002][ T1] Key type ._fscrypt registered
[ 16.853703][ T1] Key type .fscrypt registered
[ 16.858412][ T1] Key type fscrypt-provisioning registered
[ 16.867733][ T1] Key type big_key registered
[ 16.917222][ T1] Key type encrypted registered
[ 16.931503][ T1] Freeing unused kernel memory: 1024K
[ 16.957074][ T1] Checked W+X mappings: passed, no W+X pages found
[ 16.963442][ T1] Run /init as init process
Loading, please wait...
[ 17.128356][ T58] scsi 2:0:0:0: Direct-Access USB SanDisk 3.2Gen1 1.00 PQ: 0 ANSI: 6
[ 17.147829][ T7] sd 2:0:0:0: [sda] 60125184 512-byte logical blocks: (30.8 GB/28.7 GiB)
[ 17.158626][ T7] sd 2:0:0:0: [sda] Write Protect is off
[ 17.175978][ T7] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 17.204938][ T7] sda: sda1
Starting version 247.3-7+deb11u1
[ 17.227000][ T7] sd 2:0:0:0: [sda] Attached SCSI removable disk
[ 18.352877][ T147] input: gpio_keys as /devices/platform/gpio_keys/input/input0
[ 18.545258][ T147] usbcore: registered new interface driver uas
[ 18.848481][ T7] mvsdio f1090000.mvsdio: Got CD GPIO
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.36.1
[/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1
rootfs: clean, 18907/1880480 files, 485624/7515392 blocks
done.
[ 29.676267][ T168] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 29.758903][ T168] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.96 booting
Using makefile-style concurrent boot in runlevel S.
Setting hostname to 'debian'...done.
Starting fake hwclock: loading system time.
Fri Mar 31 23:58:35 UTC 2023
Starting hotplug events dispatcher: systemd-udevd.
Synthesizing the initial hotplug events (subsystems)...done.
Synthesizing the initial hotplug events (devices)...done.
Waiting for /dev to be fully populated...[ 33.756879][ C0] random: crng init done
[ 34.505992][ T363] orion_wdt: Initial timeout 25 sec
[ 35.277790][ T367] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 35.346357][ T358] marvell-cesa f1030000.crypto: CESA device successfully registered
done.
Not activating swap on swapfile. ... (warning).
[ 37.109620][ T508] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro. Quota mode: none.
Will now check all file systems.
Checking all file systems.
LABEL=rootfs is mounted
Done checking file systems.
Log is being saved in /var/log/fsck/checkfs if that location is writable.
Cleaning up temporary files...Cleaning /tmp...done.
/tmp.
[ 39.845777][ T797] Adding 524284k swap on /swapfile1. Priority:-2 extents:13 across:17840620k FS
Will now mount local filesystems:.
Will now activate swapfile swap, if any:swapon: /swapfile1: found signature [pagesize=4096, signature=swap]
swapon: /swapfile1: pagesize=4096, swapsize=536870912, devsize=536870912
swapon /swapfile1
done.
Checking minimum space in /tmp...done.
Cleaning up temporary files....
Initializing random number generator...done.
Starting Setting kernel variables: sysctl
.
Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1
Copyright 2004-2018 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/00:25:31:04:0d:95
Sending on LPF/eth0/00:25:31:04:0d:95
Sending on Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
[ 44.379905][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 44.390525][ T17] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8
DHCPOFFER of 192.168.1.186 from 192.168.1.254
DHCPREQUEST for 192.168.1.186 on eth0 to 255.255.255.255 port 67
DHCPACK of 192.168.1.186 from 192.168.1.254
bound to 192.168.1.186 -- renewal in 32779 seconds.
done.
Starting RPC port mapper daemon: rpcbind.
Starting NFS common utilities: statd idmapd.
Cleaning up temporary files....
INIT: Entering runlevel: 2
Using makefile-style concurrent boot in runlevel 2.
Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1068 (syslogd)
.
Starting NFS common utilities: statd idmapd.
Starting system message bus: dbus.
Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
Not starting NFS kernel daemon: no exports. ... (warning).
Starting NTP server: ntpd.
Starting OpenBSD Secure Shell server: sshd.
Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1108 (klogd)
.
Running local boot scripts (/etc/rc.local)
.
Debian GNU/Linux 11 debian ttyS0
debian login:
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 May 24, 2023 06:40PM |
Registered: 1 year ago Posts: 81 |
One difference between logs 1, 2 and 3 might be that I'm using different USB drives on each boot - some older Sandisk Cruzer Fits (2.0) and a new Sandisk Ultra Fit (3.2). The older Cruzer has an led on it, while the new ones don't - and neither does the Ultra. Didn't think there'd be a difference between them, but maybe they've changed the hardware between 'models' and most people won't notice it.
Hope that helps explain the discrepancies.
Hope that helps explain the discrepancies.
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 May 24, 2023 06:40PM |
Registered: 1 year ago Posts: 81 |
bodhi Wrote:
-------------------------------------------------------
> That truncated log is not good!
>
> When you post the good log, please also do this in Debian.
Here's that output on my live system:
-------------------------------------------------------
> That truncated log is not good!
>
> When you post the good log, please also do this in Debian.
> cat /proc/mtd
Here's that output on my live system:
$ cat /proc/mtd dev: size erasesize name mtd0: 00200000 00020000 "u-boot" mtd1: 00300000 00020000 "uImage" mtd2: 00300000 00020000 "uImage2" mtd3: 00800000 00020000 "failsafe" mtd4: 07000000 00020000 "root"
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 May 24, 2023 06:55PM |
Admin Registered: 13 years ago Posts: 18,545 |
dhargens,
> And here's a non-truncated boot from the rear port
> using a USB 3 drive. It too has errors in the same
> place as above.
I don't see any error in this log.
The above is OK. They are not errors. Just the scanning for all potential USB and SATA disks drives.
And finally u-boot found the boot drive
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> And here's a non-truncated boot from the rear port
> using a USB 3 drive. It too has errors in the same
> place as above.
I don't see any error in this log.
> Loading envs from usb 1... > ** Bad device specification usb 1 ** > Couldn't find partition usb 1:1 > Can't set block device > Loading envs from usb 2... > ** Bad device specification usb 2 ** > Couldn't find partition usb 2:1 > Can't set block device > Loading envs from usb 3... > ** Bad device specification usb 3 ** > Couldn't find partition usb 3:1 > Can't set block device > Loading envs from sata 0... > ** Bad device specification sata 0 ** > Couldn't find partition sata 0:1 > Can't set block device > Loading envs from sata 1... > ** Bad device specification sata 1 ** > Couldn't find partition sata 1:1 > Can't set block device > Loading envs from sata 2... > ** Bad device specification sata 2 ** > Couldn't find partition sata 2:1 > Can't set block device > Loading envs from sata 3... > ** Bad device specification sata 3 ** > Couldn't find partition sata 3:1 > Can't set block device
The above is OK. They are not errors. Just the scanning for all potential USB and SATA disks drives.
And finally u-boot found the boot drive
scanning usb for storage devices... 1 Storage Device(s) found device usb 0:1 1 bytes read in 20 ms (0 Bytes/s) Found bootable drive on usb 0
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 May 24, 2023 07:00PM |
Admin Registered: 13 years ago Posts: 18,545 |
Ah I see that was your question in a post before.
They are infornation only, not errors. Wish I can suppress them, but I can't :)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Quote
Here's a non-truncated log of a boot with a USB 2 drive in the top port. I note that there's more error messages ("Bad device specification") when loading envs from usb & sata - but I don't know why.
They are infornation only, not errors. Wish I can suppress them, but I can't :)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 May 24, 2023 07:04PM |
Registered: 1 year ago Posts: 81 |
bodhi Wrote:
-------------------------------------------------------
> dhargens,
>
> I don't see any error in this log.
> scanning for all potential USB and SATA disks
> drives.
>
> And finally u-boot found the boot drive
All of these booted and work, so I thought that was a success.
-------------------------------------------------------
> dhargens,
>
> I don't see any error in this log.
> > Loading envs from usb 1... > > ** Bad device specification usb 1 ** > > Couldn't find partition usb 1:1 > > Can't set block device > > Loading envs from usb 2... > > ** Bad device specification usb 2 ** > > Couldn't find partition usb 2:1 > > Can't set block device > > Loading envs from usb 3... > > ** Bad device specification usb 3 ** > > Couldn't find partition usb 3:1 > > Can't set block device > > Loading envs from sata 0... > > ** Bad device specification sata 0 ** > > Couldn't find partition sata 0:1 > > Can't set block device > > Loading envs from sata 1... > > ** Bad device specification sata 1 ** > > Couldn't find partition sata 1:1 > > Can't set block device > > Loading envs from sata 2... > > ** Bad device specification sata 2 ** > > Couldn't find partition sata 2:1 > > Can't set block device > > Loading envs from sata 3... > > ** Bad device specification sata 3 ** > > Couldn't find partition sata 3:1 > > Can't set block device> The above is OK. They are not errors. Just the
> scanning for all potential USB and SATA disks
> drives.
>
> And finally u-boot found the boot drive
> scanning usb for storage devices... 1 Storage > Device(s) found > device usb 0:1 > 1 bytes read in 20 ms (0 Bytes/s) > Found bootable drive on usb 0Ok, well you would know better than I. The last two that had that report differed from the first, and I thought it might be significant, so I pointed it out.
All of these booted and work, so I thought that was a success.
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 May 24, 2023 07:10PM |
Admin Registered: 13 years ago Posts: 18,545 |
> They are infornation only, not errors. Wish I can
> suppress them, but I can't :)
I migth be able to make them less noisy. But that will be some day when I can revisit this subject.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> suppress them, but I can't :)
I migth be able to make them less noisy. But that will be some day when I can revisit this subject.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 May 24, 2023 07:27PM |
Registered: 1 year ago Posts: 81 |
bodhi Wrote:
-------------------------------------------------------
> I migth be able to make them less noisy. But that
> will be some day when I can revisit this subject.
No worries. As long as it's expected, then I'm good with it. Was trying to point out a difference between boots, which didn't really make sense to me. Seems it's USB hardware, and when I get back I'll look at it further and update as needed.
-------------------------------------------------------
> I migth be able to make them less noisy. But that
> will be some day when I can revisit this subject.
No worries. As long as it's expected, then I'm good with it. Was trying to point out a difference between boots, which didn't really make sense to me. Seems it's USB hardware, and when I get back I'll look at it further and update as needed.
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 May 24, 2023 07:44PM |
Admin Registered: 13 years ago Posts: 18,545 |
I think we might not be done yet (my mistake in the envs image). So stay tume.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 May 24, 2023 07:55PM |
Registered: 1 year ago Posts: 81 |
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 May 24, 2023 08:13PM |
Admin Registered: 13 years ago Posts: 18,545 |
dhargens,
> I'll be glad to help when I return on the 5th or
> so.
OK cool! in the mean time I put this warning in the 1st post until I can figure out some weird message while flashing the default envs image.
Things look normal in using, but nandwrite output some message that could be wrong. I want to make sure that I am seeing artifacts of a bad nandwrite binary version.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> I'll be glad to help when I return on the 5th or
> so.
OK cool! in the mean time I put this warning in the 1st post until I can figure out some weird message while flashing the default envs image.
Quote
Please do not use. I'm revising this installation instruction and upload new version
Things look normal in using, but nandwrite output some message that could be wrong. I want to make sure that I am seeing artifacts of a bad nandwrite binary version.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 May 25, 2023 06:28PM |
Admin Registered: 13 years ago Posts: 18,545 |
I've uploaded a new tarball. In this I updated the envs related files (u-boot kwb image is the same). The envs was updated slightly to correct typos. The envs image was updated to avoid misleading error message during flashing.
This should be the final update.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 05/25/2023 10:02PM by bodhi.
uboot.2023.04-tld-1.pogo_v4.environment.img uboot.2023.04-tld-1.pogo_v4.environment uboot.2023.04-tld-1.pogo_v4.boot.scr
This should be the final update.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 05/25/2023 10:02PM by bodhi.
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 May 30, 2023 01:15PM |
Registered: 1 year ago Posts: 81 |
I updated a previously updated 2023.04 with the newest version from Post 1, and it boots fine. I don't have a serial connection for another week, so I can only see dmesg output, and it looks fine. I corrected the 'ethaddr' to what's on the V4's label, but otherwise all vars are from the update. I see there's no 'cpu' in the LED trigger file, though I'm not sure that was added in this update.
I'll post the serial connection next week, and whatever's needed to confirm things.
I'll post the serial connection next week, and whatever's needed to confirm things.
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 May 30, 2023 02:26PM |
Admin Registered: 13 years ago Posts: 18,545 |
dhargens,
CPU LED trigger is in the kernel, not in u-boot. I think I will release new Kirkwood kernel version sometime this week.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
CPU LED trigger is in the kernel, not in u-boot. I think I will release new Kirkwood kernel version sometime this week.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 May 30, 2023 05:00PM |
Registered: 4 years ago Posts: 54 |
Thank you for this thread. Last week, via eBay, it inspired me to add a V4 to my Pogoplug collection. It was the last version I didn't own. I was able to use the shirt pin method to gain serial access and then install this latest U-Boot and Debian. I was a little rusty on the timing when trying to kwboot but after a few tries got it down pat!
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 May 30, 2023 08:25PM |
Admin Registered: 13 years ago Posts: 18,545 |
bluzfanmr1,
> I was able to use the shirt pin method to gain
> serial access
Cool! I thought I was the only one lazy and soldering challenge :)
> and then install this latest U-Boot
> and Debian. I was a little rusty on the timing
> when trying to kwboot but after a few tries got it
> down pat!
Awesome!
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> I was able to use the shirt pin method to gain
> serial access
Cool! I thought I was the only one lazy and soldering challenge :)
> and then install this latest U-Boot
> and Debian. I was a little rusty on the timing
> when trying to kwboot but after a few tries got it
> down pat!
Awesome!
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 May 30, 2023 09:54PM |
Registered: 7 years ago Posts: 7 |
I also followed your instructions and successfully got the new 2023.04 U-Boot Kirkwood PogoV4 working without any issue. I upgraded my Pogoplug V4 A3 from the last 2017.07 U Boot.
`
I have a 1TB hard drive that sits inside the top slot, but still boot off the usb 2.0 flash drive; I use the pogoplug for a home SAMBA server with just 2 Macs, 2 Windows and 1 chrombook.
I needed to briefly look for 'fw_printenv' as it was not in the uboot-tools; simply had to 'apt install libubootenv'.
On review of my old fw_printenv with the new one - I see that 'machid=f78' and 'arcNumber=3860' are no longer needed
I have learned and done a lot with your help; Thank you
`
I have a 1TB hard drive that sits inside the top slot, but still boot off the usb 2.0 flash drive; I use the pogoplug for a home SAMBA server with just 2 Macs, 2 Windows and 1 chrombook.
I needed to briefly look for 'fw_printenv' as it was not in the uboot-tools; simply had to 'apt install libubootenv'.
On review of my old fw_printenv with the new one - I see that 'machid=f78' and 'arcNumber=3860' are no longer needed
I have learned and done a lot with your help; Thank you
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 May 30, 2023 10:43PM |
Admin Registered: 13 years ago Posts: 18,545 |
dancyran,
> I also followed your instructions and successfully
> got the new 2023.04 U-Boot Kirkwood PogoV4
> working without any issue. I upgraded my Pogoplug
> V4 A3 from the last 2017.07 U Boot.
Cool!
> On review of my old fw_printenv with the new one -
> I see that 'machid=f78' and 'arcNumber=3860' are
> no longer needed
That's right.The new default envs removed these envs.
> I have learned and done a lot with your help;
> Thank you
Thanks for the feedback!
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> I also followed your instructions and successfully
> got the new 2023.04 U-Boot Kirkwood PogoV4
> working without any issue. I upgraded my Pogoplug
> V4 A3 from the last 2017.07 U Boot.
Cool!
> On review of my old fw_printenv with the new one -
> I see that 'machid=f78' and 'arcNumber=3860' are
> no longer needed
That's right.The new default envs removed these envs.
> I have learned and done a lot with your help;
> Thank you
Thanks for the feedback!
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 May 31, 2023 02:03PM |
Registered: 4 years ago Posts: 54 |
Since a serial connection for the Pogoplug V4/Mobile is much harder than a serial connection for the Pogoplug E02, I thought I'd share a picture of my serial cable that uses the shirt pin method. This option eliminates the need for soldering.
You can firmly but carefully push each pin into the solder for each connection until they stick without falling. I cut off the top of the pins to get them to fit into the end of the cable connectors. The middle pin has tape around it to keep the 3 connections from touching. Just be careful not to push the pins too hard or you will end up with one sticking deep in your thumb like I did!
@bodhi thank you for this site and all your help!
You can firmly but carefully push each pin into the solder for each connection until they stick without falling. I cut off the top of the pins to get them to fit into the end of the cable connectors. The middle pin has tape around it to keep the 3 connections from touching. Just be careful not to push the pins too hard or you will end up with one sticking deep in your thumb like I did!
@bodhi thank you for this site and all your help!
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 May 31, 2023 03:31PM |
Admin Registered: 13 years ago Posts: 18,545 |
> You can firmly but carefully push each pin into
> the solder for each connection until they stick
> without falling. I cut off the top of the pins to
> get them to fit into the end of the cable
> connectors. The middle pin has tape around it to
> keep the 3 connections from touching. Just be
> careful not to push the pins too hard or you will
> end up with one sticking deep in your thumb like I
> did!
Nice job! better than my original approach. I just used 3 test clips to hold the shirt pins and connect the serial module converter pins to the 3 test clips. This approach is very temporary (the whole contraption is fragile and could fall apart).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> the solder for each connection until they stick
> without falling. I cut off the top of the pins to
> get them to fit into the end of the cable
> connectors. The middle pin has tape around it to
> keep the 3 connections from touching. Just be
> careful not to push the pins too hard or you will
> end up with one sticking deep in your thumb like I
> did!
Nice job! better than my original approach. I just used 3 test clips to hold the shirt pins and connect the serial module converter pins to the 3 test clips. This approach is very temporary (the whole contraption is fragile and could fall apart).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 June 05, 2023 02:52PM |
Registered: 4 years ago Posts: 54 |
I went ahead and updated to the latest kernel (linux-6.3.5-kirkwood-tld-1-bodhi.tar.bz2 (02 Jun 2023)) on my new Pogoplug V4 and it stopped booting. I hooked up serial console and when booting it stops at the same spot below, whether regular booting or using kwboot. Do I have a hardware issue with this new box or have I done something wrong?
root@Pogoplug2:~# ./kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2023.04-tld-1.pogo_v4.kwb -p kwboot version 2022.07-00607-g36b661dc91 Patching image boot signature to UART Sending boot message. Please reboot the target...- Sending boot image header (512 bytes)... 25 % [.... ] Done Sending boot image data (516244 bytes)... 0 % [......................................................................] 1 % [......................................................................] 3 % [......................................................................] 5 % [......................................................................] 6 % [......................................................................] 8 % [......................................................................] 10 % [......................................................................] 12 % [......................................................................] 13 % [......................................................................] 15 % [......................................................................] 17 % [......................................................................] 19 % [......................................................................] 20 % [......................................................................] 22 % [......................................................................] 24 % [......................................................................] 26 % [......................................................................] 27 % [......................................................................] 29 % [......................................................................] 31 % [......................................................................] 33 % [......................................................................] 34 % [......................................................................] 36 % [......................................................................] 38 % [......................................................................] 39 % [......................................................................] 41 % [......................................................................] 43 % [......................................................................] 45 % [......................................................................] 46 % [......................................................................] 48 % [......................................................................] 50 % [......................................................................] 52 % [......................................................................] 53 % [......................................................................] 55 % [......................................................................] 57 % [......................................................................] 59 % [......................................................................] 60 % [......................................................................] 62 % [......................................................................] 64 % [......................................................................] 65 % [......................................................................] 67 % [......................................................................] 69 % [......................................................................] 71 % [......................................................................] 72 % [......................................................................] 74 % [......................................................................] 76 % [......................................................................] 78 % [......................................................................] 79 % [......................................................................] 81 % [......................................................................] 83 % [......................................................................] 85 % [......................................................................] 86 % [......................................................................] 88 % [......................................................................] 90 % [......................................................................] 92 % [......................................................................] 93 % [......................................................................] 95 % [......................................................................] 97 % [......................................................................] 98 % [............................................ ] Done Finishing transfer [Type Ctrl-\ + c to quit] U-Boot 2023.04-tld-1 (May 10 2023 - 23:00:14 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 Model: Cloud Engines PogoPlug Series 4 DRAM: 128 MiB Core: 20 devices, 16 uclasses, devicetree: separate NAND: 128 MiB MMC: mvsdio@90000: 0 Loading Environment from NAND... OK
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 June 05, 2023 04:47PM |
Admin Registered: 13 years ago Posts: 18,545 |
bluzfanmr1,
> Do I have a
> hardware issue with this new box or have I done
> something wrong?
The appearance does look much like a HW problem, but I'd bet it is not. Just your envs are messed up.
> U-Boot 2023.04-tld-1 (May 10 2023 - 23:00:14
> -0700)
> Pogoplug V4
>
> SoC: Kirkwood 88F6192_A1
> Model: Cloud Engines PogoPlug Series 4
> DRAM: 128 MiB
> Core: 20 devices, 16 uclasses, devicetree:
> separate
> NAND: 128 MiB
> MMC: mvsdio@90000: 0
> Loading Environment from NAND... OK
At this point, the current envs on NAND come in to play. So its' likely that you envs were set to netconsole only. So look back in your installation (keeping a log of what you did during installation would be very helpful)
1. Did you install previous u-boot before? and did you set up netconsole? if you kept the log, or remember the serverip that you used for netconsole. Start netconsole on that box and see if the u-boot banner wil apper and you can interrupt the countdown.
2 . If the above did not work then try kwboot the older version (u-boot 2017.07). And I will suggest more recovery steps.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 06/05/2023 04:49PM by bodhi.
> Do I have a
> hardware issue with this new box or have I done
> something wrong?
The appearance does look much like a HW problem, but I'd bet it is not. Just your envs are messed up.
> U-Boot 2023.04-tld-1 (May 10 2023 - 23:00:14
> -0700)
> Pogoplug V4
>
> SoC: Kirkwood 88F6192_A1
> Model: Cloud Engines PogoPlug Series 4
> DRAM: 128 MiB
> Core: 20 devices, 16 uclasses, devicetree:
> separate
> NAND: 128 MiB
> MMC: mvsdio@90000: 0
> Loading Environment from NAND... OK
At this point, the current envs on NAND come in to play. So its' likely that you envs were set to netconsole only. So look back in your installation (keeping a log of what you did during installation would be very helpful)
1. Did you install previous u-boot before? and did you set up netconsole? if you kept the log, or remember the serverip that you used for netconsole. Start netconsole on that box and see if the u-boot banner wil apper and you can interrupt the countdown.
2 . If the above did not work then try kwboot the older version (u-boot 2017.07). And I will suggest more recovery steps.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 06/05/2023 04:49PM by bodhi.
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 June 05, 2023 05:15PM |
Admin Registered: 13 years ago Posts: 18,545 |
Further more, try finding your box in the network, and log in. It might have booted into Debian, but you can not see that in serial console. In this case, fixing the envs is easy.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 June 05, 2023 05:21PM |
Registered: 4 years ago Posts: 54 |
bodhi Wrote:
-------------------------------------------------------
> bluzfanmr1,
>
> > Do I have a
> > hardware issue with this new box or have I done
> > something wrong?
>
> The appearance does look much like a HW problem,
> but I'd bet it is not. Just your envs are messed
> up.
>
>
> > U-Boot 2023.04-tld-1 (May 10 2023 - 23:00:14
> > -0700)
> > Pogoplug V4
> >
> > SoC: Kirkwood 88F6192_A1
> > Model: Cloud Engines PogoPlug Series 4
> > DRAM: 128 MiB
> > Core: 20 devices, 16 uclasses, devicetree:
> > separate
> > NAND: 128 MiB
> > MMC: mvsdio@90000: 0
> > Loading Environment from NAND... OK
>
> At this point, the current envs on NAND come in to
> play. So its' likely that you envs were set to
> netconsole only. So look back in your installation
> (keeping a log of what you did during installation
> would be very helpful)
>
> 1. Did you install previous u-boot before? and
> did you set up netconsole? if you kept the log, or
> remember the serverip that you used for
> netconsole. Start netconsole on that box and see
> if the u-boot banner wil apper and you can
> interrupt the countdown.
>
> 2 . If the above did not work then try kwboot the
> older version (u-boot 2017.07). And I will suggest
> more recovery steps.
I know better, but didn't keep the logs. Lesson learned. I did not try the previous u-boot (2017) and installed 2023.04 straight from stock. Yes, I had set up netconsole, but it wasn't working. I didn't think of trying to kwboot the older u-boot, so I tried it and it worked! I now have both serial and netconsole working, though for netconsole I only see the u-boot and not the kernel boot.
The last thing I did was update the kernel on this box and 2 other boxes. The other 2 boxes came back up fine but the new V4 with the 2023.04 had this issue. Here is what I have now:
-------------------------------------------------------
> bluzfanmr1,
>
> > Do I have a
> > hardware issue with this new box or have I done
> > something wrong?
>
> The appearance does look much like a HW problem,
> but I'd bet it is not. Just your envs are messed
> up.
>
>
> > U-Boot 2023.04-tld-1 (May 10 2023 - 23:00:14
> > -0700)
> > Pogoplug V4
> >
> > SoC: Kirkwood 88F6192_A1
> > Model: Cloud Engines PogoPlug Series 4
> > DRAM: 128 MiB
> > Core: 20 devices, 16 uclasses, devicetree:
> > separate
> > NAND: 128 MiB
> > MMC: mvsdio@90000: 0
> > Loading Environment from NAND... OK
>
> At this point, the current envs on NAND come in to
> play. So its' likely that you envs were set to
> netconsole only. So look back in your installation
> (keeping a log of what you did during installation
> would be very helpful)
>
> 1. Did you install previous u-boot before? and
> did you set up netconsole? if you kept the log, or
> remember the serverip that you used for
> netconsole. Start netconsole on that box and see
> if the u-boot banner wil apper and you can
> interrupt the countdown.
>
> 2 . If the above did not work then try kwboot the
> older version (u-boot 2017.07). And I will suggest
> more recovery steps.
I know better, but didn't keep the logs. Lesson learned. I did not try the previous u-boot (2017) and installed 2023.04 straight from stock. Yes, I had set up netconsole, but it wasn't working. I didn't think of trying to kwboot the older u-boot, so I tried it and it worked! I now have both serial and netconsole working, though for netconsole I only see the u-boot and not the kernel boot.
The last thing I did was update the kernel on this box and 2 other boxes. The other 2 boxes came back up fine but the new V4 with the 2023.04 had this issue. Here is what I have now:
Pogov4> printenv baudrate=115200 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; reset bootcmd_exec=if run load_uimage; then; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb console=ttyS0,115200 device=0:1 devices=sata usb mmc disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-pogoplug_v4.dtb ethact=egiga0 ethaddr=00:25:31:xx:xx:xx fdtcontroladdr=7b51650 if_netconsole=ping $serverip ipaddr=10.1.1.210 load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x2100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) nc_ready=1 ncip=10.1.1.199 preboot=run preboot_nc preboot_nc=setenv nc_ready 0; for pingstat in 1 2 3; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb reset; sleep 1; usb reset"; setenv scan_sata "sata init"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=10.1.1.199 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin serial,nc; setenv stdout serial,nc; setenv stderr serial,nc; version stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=echo Initializing devices...; setenv init_usb "usb reset; sleep 1; usb reset"; setenv init_sata sata init; setenv init_mmc mmc rescan; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in $disks; do if test $uenv_loaded -eq 0; then setenv device_type $devtype; setenv disk_number $disknum; run uenv_read; fi; done; done; uenv_read=echo Loading envs from $device_type $disk_number...; if load $device_type $disk_number:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; echo ... envs loaded; fi ver=U-Boot 2023.04-tld-1 (May 10 2023 - 23:00:14 -0700)\ Pogoplug V4 Environment size: 3090/131068 bytes
Pogov4> reset
resetting ...
U-Boot 2023.04-tld-1 (May 10 2023 - 23:00:14 -0700)
Pogoplug V4
SoC: Kirkwood 88F6192_A1
Model: Cloud Engines PogoPlug Series 4
DRAM: 128 MiB
Core: 20 devices, 16 uclasses, devicetree: separate
NAND: 128 MiB
MMC: mvsdio@90000: 0
Loading Environment from NAND... OK
In: serial
Out: serial
Err: serial
pcie0.0: Link up
Net: eth0: ethernet-controller@72000
ethernet-controller@72000 Waiting for PHY auto negotiation to complete...... done
Using ethernet-controller@72000 device
host 10.1.1.1 is alive
ethernet-controller@72000 Waiting for PHY auto negotiation to complete....... done
Using ethernet-controller@72000 device
host 10.1.1.1 is alive
ethernet-controller@72000 Waiting for PHY auto negotiation to complete...... done
Using ethernet-controller@72000 device
host 10.1.1.1 is alive
U-Boot 2023.04-tld-1 (May 10 2023 - 23:00:14 -0700)
Pogoplug V4
ethernet-controller@72000 Waiting for PHY auto negotiation to complete...... done
gcc (Debian 12.2.0-14) 12.2.0
GNU ld (GNU Binutils for Debian) 2.40
Hit any key to stop autoboot: 0
Initializing devices...
resetting USB...
Bus ehci@50000: USB EHCI 1.00
Bus xhci_pci: Register 400081f NbrPorts 4
Starting the controller
USB XHCI 1.00
scanning bus ehci@50000 for devices... 1 USB Device(s) found
scanning bus xhci_pci for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
resetting USB...
Bus ehci@50000: USB EHCI 1.00
Bus xhci_pci: Register 400081f NbrPorts 4
Starting the controller
USB XHCI 1.00
scanning bus ehci@50000 for devices... 1 USB Device(s) found
scanning bus xhci_pci for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Card did not respond to voltage select! : -110
Loading envs from sata 0...
** Bad device specification sata 0 **
Couldn't find partition sata 0:1
Can't set block device
Loading envs from sata 1...
** Bad device specification sata 1 **
Couldn't find partition sata 1:1
Can't set block device
Loading envs from sata 2...
** Bad device specification sata 2 **
Couldn't find partition sata 2:1
Can't set block device
Loading envs from sata 3...
** Bad device specification sata 3 **
Couldn't find partition sata 3:1
Can't set block device
Loading envs from usb 0...
Failed to load '/boot/uEnv.txt'
Loading envs from usb 1...
** Bad device specification usb 1 **
Couldn't find partition usb 1:1
Can't set block device
Loading envs from usb 2...
** Bad device specification usb 2 **
Couldn't find partition usb 2:1
Can't set block device
Loading envs from usb 3...
** Bad device specification usb 3 **
Couldn't find partition usb 3:1
Can't set block device
Loading envs from mmc 0...
Card did not respond to voltage select! : -110
** Bad device specification mmc 0 **
Couldn't find partition mmc 0:1
Can't set block device
Loading envs from mmc 1...
** Bad device specification mmc 1 **
Couldn't find partition mmc 1:1
Can't set block device
Loading envs from mmc 2...
** Bad device specification mmc 2 **
Couldn't find partition mmc 2:1
Can't set block device
Loading envs from mmc 3...
** Bad device specification mmc 3 **
Couldn't find partition mmc 3:1
Can't set block device
running scan_disk ...
Scan device sata
device sata 0:1
** Bad device specification sata 0 **
Couldn't find partition sata 0:1
Can't set block device
device sata 1:1
** Bad device specification sata 1 **
Couldn't find partition sata 1:1
Can't set block device
device sata 2:1
** Bad device specification sata 2 **
Couldn't find partition sata 2:1
Can't set block device
device sata 3:1
** Bad device specification sata 3 **
Couldn't find partition sata 3:1
Can't set block device
Scan device usb
resetting USB...
Bus ehci@50000: USB EHCI 1.00
Bus xhci_pci: Register 400081f NbrPorts 4
Starting the controller
USB XHCI 1.00
scanning bus ehci@50000 for devices... 1 USB Device(s) found
scanning bus xhci_pci for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
resetting USB...
Bus ehci@50000: USB EHCI 1.00
Bus xhci_pci: Register 400081f NbrPorts 4
Starting the controller
USB XHCI 1.00
scanning bus ehci@50000 for devices... 1 USB Device(s) found
scanning bus xhci_pci for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
device usb 0:1
1 bytes read in 12 ms (0 Bytes/s)
Found bootable drive on usb 0
loading uImage ...
6116624 bytes read in 321 ms (18.2 MiB/s)
loading uInitrd ...
10337792 bytes read in 515 ms (19.1 MiB/s)
loading DTB /boot/dts/kirkwood-pogoplug_v4.dtb ...
10178 bytes read in 21 ms (472.7 KiB/s)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-6.3.5-kirkwood-tld-1
Created: 2023-06-03 18:08:32 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 6116560 Bytes = 5.8 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02100000 ...
Image Name: initramfs-6.3.5-kirkwood-tld-1
Created: 2023-06-03 18:08:43 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 10337728 Bytes = 9.9 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01c00000
Booting using the fdt blob at 0x1c00000
Working FDT set to 1c00000
Starting kernel ...
Loading Kernel Image
Loading Ramdisk to 07171000, end 07b4cdc0 ... OK
Loading Device Tree to 0716b000, end 071707c1 ... OK
Working FDT set to 716b000
Starting kernel ...
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 6.3.5-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 PREEMPT Wed May 31 18:12:24 PDT 2023
[ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: Pogoplug v4
[ 0.000000][ T0] Memory policy: Data cache writeback
[ 0.000000][ T0] Zone ranges:
[ 0.000000][ T0] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000][ T0] Movable zone start for each node
[ 0.000000][ T0] Early memory node ranges
[ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
[ 0.000000][ T0] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000][ T0] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000][ T0] Memory: 98148K/131072K available (12288K kernel code, 1697K rwdata, 5228K rodata, 1024K init, 302K bss, 32924K reserved, 0K cma-reserved)
[ 0.000000][ T0] trace event string verifier disabled
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] Trampoline variant of Tasks RCU enabled.
[ 0.000000][ T0] Tracing variant of Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[ 0.000003][ T0] sched_clock: 32 bits at 167MHz, resolution 6ns, wraps every 12884901885ns
[ 0.000074][ T0] Switching to timer-based delay loop, resolution 6ns
[ 0.003105][ T0] Console: colour dummy device 80x30
[ 0.003201][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666)
[ 0.003243][ T0] pid_max: default: 32768 minimum: 301
[ 0.004453][ T0] LSM: initializing lsm=capability,integrity
[ 0.005133][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.005189][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.009090][ T0] CPU: Testing write buffer coherency: ok
[ 0.014151][ T1] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.014182][ T1] cblist_init_generic: Setting shift to 0 and lim to 1.
[ 0.014767][ T1] cblist_init_generic: Setting shift to 0 and lim to 1.
[ 0.015525][ T1] Setting up static identity map for 0x100000 - 0x100058
[ 0.016017][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[ 0.016666][ T1] rcu: Hierarchical SRCU implementation.
[ 0.016692][ T1] rcu: Max phase no-delay instances is 1000.
[ 0.019635][ T1] devtmpfs: initialized
[ 0.032057][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.032127][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.032909][ T1] prandom: seed boundary self test passed
[ 0.039281][ T1] prandom: 100 self tests passed
[ 0.039306][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.044178][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.045621][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.047954][ T1] audit: initializing netlink subsys (disabled)
[ 0.051390][ T1] thermal_sys: Registered thermal governor 'step_wise'
[ 0.052028][ T16] audit: type=2000 audit(0.040:1): state=initialized audit_enabled=0 res=1
[ 0.052261][ T1] cpuidle: using governor ladder
[ 0.052389][ T1] cpuidle: using governor menu
[ 0.053279][ T1] Feroceon L2: Enabling L2
[ 0.053334][ T1] Feroceon L2: Cache support initialised.
[ 0.066968][ T1] No ATAGs?
[ 0.430097][ T1] raid6: int32x8 gen() 74 MB/s
[ 0.770096][ T1] raid6: int32x4 gen() 74 MB/s
[ 1.110136][ T1] raid6: int32x2 gen() 96 MB/s
[ 1.450094][ T1] raid6: int32x1 gen() 74 MB/s
[ 1.450113][ T1] raid6: using algorithm int32x2 gen() 96 MB/s
[ 1.790096][ T1] raid6: .... xor() 58 MB/s, rmw enabled
[ 1.790114][ T1] raid6: using intx1 recovery algorithm
[ 1.791855][ T1] SCSI subsystem initialized
[ 1.793046][ T1] usbcore: registered new interface driver usbfs
[ 1.793141][ T1] usbcore: registered new interface driver hub
[ 1.793230][ T1] usbcore: registered new device driver usb
[ 1.793857][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 1.793872][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.793926][ T1] PTP clock support registered
[ 1.797593][ T1] vgaarb: loaded
[ 1.811039][ T1] clocksource: Switched to clocksource orion_clocksource
[ 1.813241][ T1] VFS: Disk quotas dquot_6.6.0
[ 1.813381][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.848793][ T1] NET: Registered PF_INET protocol family
[ 1.849229][ T1] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 1.851515][ T1] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 1.851914][ T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 1.851956][ T1] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 1.852006][ T1] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 1.852056][ T1] TCP: Hash tables configured (established 1024 bind 1024)
[ 1.852618][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 1.852763][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 1.852814][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 1.853251][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 1.854696][ T1] RPC: Registered named UNIX socket transport module.
[ 1.854715][ T1] RPC: Registered udp transport module.
[ 1.854724][ T1] RPC: Registered tcp transport module.
[ 1.854731][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.854762][ T1] PCI: CLS 0 bytes, default 32
[ 1.855418][ T1] NetWinder Floating Point Emulator V0.97 (double precision)
[ 1.861787][ T30] Trying to unpack rootfs image as initramfs...
[ 4.735451][ T30] Freeing initrd memory: 10096K
[ 5.702827][ T1] Initialise system trusted keyrings
[ 5.702963][ T1] Key type blacklist registered
[ 5.704855][ T1] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 5.705106][ T1] zbud: loaded
[ 5.708991][ T1] NFS: Registering the id_resolver key type
[ 5.709064][ T1] Key type id_resolver registered
[ 5.709077][ T1] Key type id_legacy registered
[ 5.709221][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 5.709250][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 5.710030][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 5.710937][ T1] fuse: init (API version 7.38)
[ 5.711955][ T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 5.712521][ T1] orangefs_init: module version upstream loaded
[ 5.712660][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled
[ 5.863044][ T1] xor: measuring software checksum speed
[ 5.876307][ T1] arm4regs : 746 MB/sec
[ 5.898344][ T1] 8regs : 447 MB/sec
[ 5.913890][ T1] 32regs : 634 MB/sec
[ 5.913904][ T1] xor: using function: arm4regs (746 MB/sec)
[ 5.913929][ T1] async_tx: api initialized (async)
[ 5.913957][ T1] Key type asymmetric registered
[ 5.913969][ T1] Asymmetric key parser 'x509' registered
[ 5.975910][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[ 5.976222][ T1] io scheduler bfq registered
[ 6.257635][ T1] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 47
[ 6.257670][ T1] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 49
[ 6.258389][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 6.260606][ T1] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 6.262471][ T1] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 6.264369][ T1] mv_xor f1060800.xor: Marvell shared XOR driver
[ 6.333319][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 6.340090][ T1] mv_xor f1060900.xor: Marvell shared XOR driver
[ 6.403343][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 6.410525][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 6.413494][ T1] printk: console [ttyS0] disabled
[ 6.413665][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 27, base_baud = 10416666) is a 16550A
[ 6.413780][ T1] printk: console [ttyS0] enabled
[ 7.302801][ T1] loop: module loaded
[ 7.308084][ T1] sata_mv f1080000.sata: slots 32 ports 2
[ 7.320471][ T1] scsi host0: sata_mv
[ 7.325888][ T1] scsi host1: sata_mv
[ 7.330345][ T1] ata1: SATA max UDMA/133 irq 28
[ 7.335228][ T1] ata2: SATA max UDMA/133 irq 28
[ 7.342285][ T1] Could not find a valid ONFI parameter page, trying bit-wise majority to recover it
[ 7.351800][ T1] ONFI parameter recovery failed, aborting
[ 7.357462][ T1] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[ 7.364533][ T1] nand: Hynix NAND 128MiB 3,3V 8-bit
[ 7.369666][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 7.377982][ T1] Scanning device for bad blocks
[ 7.424255][ T1] Bad eraseblock 499 at 0x000003e60000
[ 7.473090][ T1] 5 cmdlinepart partitions found on MTD device orion_nand
[ 7.480043][ T1] Creating 5 MTD partitions on "orion_nand":
[ 7.485889][ T1] 0x000000000000-0x000000200000 : "u-boot"
[ 7.492763][ T1] 0x000000200000-0x000000500000 : "uImage"
[ 7.499361][ T1] 0x000000500000-0x000000800000 : "uImage2"
[ 7.506193][ T1] 0x000000800000-0x000001000000 : "failsafe"
[ 7.513120][ T1] 0x000001000000-0x000008000000 : "root"
[ 7.521218][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 7.529731][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 7.572289][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 7.671275][ T50] ata1: SATA link down (SStatus 0 SControl F300)
[ 8.012868][ T52] ata2: SATA link down (SStatus 0 SControl F300)
[ 8.322988][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:04:40:0d
[ 8.333239][ T1] orion-ehci f1050000.ehci: EHCI Host Controller
[ 8.339464][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 8.348138][ T1] orion-ehci f1050000.ehci: irq 31, io mem 0xf1050000
[ 8.381098][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 8.388246][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.03
[ 8.397229][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.405157][ T1] usb usb1: Product: EHCI Host Controller
[ 8.410718][ T1] usb usb1: Manufacturer: Linux 6.3.5-kirkwood-tld-1 ehci_hcd
[ 8.418047][ T1] usb usb1: SerialNumber: f1050000.ehci
[ 8.424900][ T1] hub 1-0:1.0: USB hub found
[ 8.429423][ T1] hub 1-0:1.0: 1 port detected
[ 8.435582][ T1] usbcore: registered new interface driver usb-storage
[ 8.443263][ T1] mousedev: PS/2 mouse device common for all mice
[ 9.521104][ T1] rtc-mv f1010300.rtc: internal RTC not ticking
[ 9.527548][ T1] i2c_dev: i2c /dev entries driver
[ 9.533798][ T1] device-mapper: uevent: version 1.0.3
[ 9.539681][ T1] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com
[ 9.549919][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 9.557251][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 9.564595][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 9.572068][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 9.578851][ T1] device-mapper: raid: Loading target version 1.15.1
[ 9.587825][ T1] ledtrig-cpu: registered to indicate activity on CPUs
[ 9.594734][ T1] hid: raw HID events driver (C) Jiri Kosina
[ 9.601244][ T1] drop_monitor: Initializing network drop monitor service
[ 9.609142][ T1] NET: Registered PF_INET6 protocol family
[ 9.617918][ T1] Segment Routing with IPv6
[ 9.622425][ T1] RPL Segment Routing with IPv6
[ 9.627254][ T1] In-situ OAM (IOAM) with IPv6
[ 9.632090][ T1] NET: Registered PF_PACKET protocol family
[ 9.638421][ T1] Key type dns_resolver registered
[ 9.666843][ T1] registered taskstats version 1
[ 9.672145][ T1] Loading compiled-in X.509 certificates
[ 9.679575][ T1] zswap: loaded using pool lzo/zbud
[ 9.685880][ T1] Key type .fscrypt registered
[ 9.690503][ T1] Key type fscrypt-provisioning registered
[ 9.706592][ T1] Key type big_key registered
[ 9.764953][ T1] Key type encrypted registered
[ 9.911303][ T102] "cryptomgr_test" (102) uses obsolete ecb(arc4) skcipher
[ 13.321001][ T1] Freeing unused kernel image (initmem) memory: 1024K
[ 13.342305][ T1] Checked W+X mappings: passed, no W+X pages found
[ 13.348683][ T1] Run /init as init process
Loading, please wait...
Starting version 247.3-7+deb11u2
[ 14.684180][ T136] input: gpio_keys as /devices/platform/gpio_keys/input/input0
[ 15.023392][ T8] mvsdio f1090000.mvsdio: Got CD GPIO
Begin: Loading essential drivers ... [ 15.513597][ T150] netpoll: netconsole: local port 6666
[ 15.518935][ T150] netpoll: netconsole: local IPv4 address 10.1.1.210
[ 15.525610][ T150] netpoll: netconsole: interface 'eth0'
[ 15.531001][ T150] netpoll: netconsole: remote port 6666
[ 15.538357][ T150] netpoll: netconsole: remote IPv4 address 10.1.1.199
[ 15.544832][ T150] netpoll: netconsole: remote ethernet address ff:ff:ff:ff:ff:ff
[ 15.552416][ T150] netpoll: netconsole: device eth0 not up yet, forcing it
[ 18.729006][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 18.739599][ T47] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 18.752002][ T150] printk: console [netcon0] enabled
[ 18.765313][ T150] netconsole: network logging started
done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Waiting for root file system ... Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
done.
Gave up waiting for root file system device. Common problems:
- Boot args (cat /proc/cmdline)
- Check rootdelay= (did the system wait long enough?)
- Missing modules (cat /proc/modules; ls /dev)
ALERT! LABEL=rootfs does not exist. Dropping to a shell!
BusyBox v1.30.1 (Debian 1:1.30.1-6+b3) built-in shell (ash)
Enter 'help' for a list of built-in commands.
(initramfs)
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 June 05, 2023 05:48PM |
Admin Registered: 13 years ago Posts: 18,545 |
bluzfanmr1,
> I know better, but didn't keep the logs. Lesson
> learned. I did not try the previous u-boot (2017)
> and installed 2023.04 straight from stock. Yes, I
> had set up netconsole, but it wasn't working. I
> didn't think of trying to kwboot the older u-boot,
> so I tried it and it worked! I now have both
> serial and netconsole working, though for
> netconsole I only see the u-boot and not the
> kernel boot.
Cool! it is normal to see u-boot log only in netconsole. Further set up is needed if you want to see kernel booting. But it will not be a complete log like with serial console.
=====
Looking at the log, the USB drive was not initialized by the kernel. So my guess is you are pluging a USB 3.0 thumb drive. Which port are you using? one of the 2 USB 3.0 in the back, or the USB 2.0 on the top?
If the USB 3.0 is attached to the USB 2.0 port on top, it's problemmatic (either use USB 2.0 thumb drive, or a USB 3.0 hub wih the top port).
If the USB 3.0 drive is attached to one of the 2 ports in the back, then it might be the case that this brand/model/capacity (please post this info) has some quirks. Try attaching to the other USB 3.0 port.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> I know better, but didn't keep the logs. Lesson
> learned. I did not try the previous u-boot (2017)
> and installed 2023.04 straight from stock. Yes, I
> had set up netconsole, but it wasn't working. I
> didn't think of trying to kwboot the older u-boot,
> so I tried it and it worked! I now have both
> serial and netconsole working, though for
> netconsole I only see the u-boot and not the
> kernel boot.
Cool! it is normal to see u-boot log only in netconsole. Further set up is needed if you want to see kernel booting. But it will not be a complete log like with serial console.
=====
Looking at the log, the USB drive was not initialized by the kernel. So my guess is you are pluging a USB 3.0 thumb drive. Which port are you using? one of the 2 USB 3.0 in the back, or the USB 2.0 on the top?
If the USB 3.0 is attached to the USB 2.0 port on top, it's problemmatic (either use USB 2.0 thumb drive, or a USB 3.0 hub wih the top port).
If the USB 3.0 drive is attached to one of the 2 ports in the back, then it might be the case that this brand/model/capacity (please post this info) has some quirks. Try attaching to the other USB 3.0 port.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 June 05, 2023 06:01PM |
Registered: 4 years ago Posts: 54 |
bodhi Wrote:
-------------------------------------------------------
> bluzfanmr1,
>
>
> > I know better, but didn't keep the logs.
> Lesson
> > learned. I did not try the previous u-boot
> (2017)
> > and installed 2023.04 straight from stock. Yes,
> I
> > had set up netconsole, but it wasn't working.
> I
> > didn't think of trying to kwboot the older
> u-boot,
> > so I tried it and it worked! I now have both
> > serial and netconsole working, though for
> > netconsole I only see the u-boot and not the
> > kernel boot.
>
> Cool! it is normal to see u-boot log only in
> netconsole.
> Further
> set up is needed if you want to see kernel
> booting. But it will not be a complete log like
> with serial console.
>
> =====
>
> Looking at the log, the USB drive was not
> initialized by the kernel. So my guess is you are
> pluging a USB 3.0 thumb drive. Which port are you
> using? one of the 2 USB 3.0 in the back, or the
> USB 2.0 on the top?
>
> If the USB 3.0 is attached to the USB 2.0 port on
> top, it's problemmatic (either use USB 2.0 thumb
> drive, or a USB 3.0 hub wih the top port).
>
> If the USB 3.0 drive is attached to one of the 2
> ports in the back, then it might be the case that
> this brand/model/capacity (please post this info)
> has some quirks. Try attaching to the other USB
> 3.0 port.
I was using a USB 2.0 but it was plugged into one of the USB 3.0 ports in the back. I plugged the USB 2.0 into the top and it works!
I don't know what happened to make it stop booting. I had previously tried moving the usb around without luck. The only thing I changed here to get it working again was kwboot with the 2017 version. I did not make that permanent or change any other environment variables. That being said, and according to the log, it's using the 2023 version of uboot again. I'm confused by that but glad it's working again. Thanks for your help!
-------------------------------------------------------
> bluzfanmr1,
>
>
> > I know better, but didn't keep the logs.
> Lesson
> > learned. I did not try the previous u-boot
> (2017)
> > and installed 2023.04 straight from stock. Yes,
> I
> > had set up netconsole, but it wasn't working.
> I
> > didn't think of trying to kwboot the older
> u-boot,
> > so I tried it and it worked! I now have both
> > serial and netconsole working, though for
> > netconsole I only see the u-boot and not the
> > kernel boot.
>
> Cool! it is normal to see u-boot log only in
> netconsole.
> Further
> set up is needed if you want to see kernel
> booting. But it will not be a complete log like
> with serial console.
>
> =====
>
> Looking at the log, the USB drive was not
> initialized by the kernel. So my guess is you are
> pluging a USB 3.0 thumb drive. Which port are you
> using? one of the 2 USB 3.0 in the back, or the
> USB 2.0 on the top?
>
> If the USB 3.0 is attached to the USB 2.0 port on
> top, it's problemmatic (either use USB 2.0 thumb
> drive, or a USB 3.0 hub wih the top port).
>
> If the USB 3.0 drive is attached to one of the 2
> ports in the back, then it might be the case that
> this brand/model/capacity (please post this info)
> has some quirks. Try attaching to the other USB
> 3.0 port.
I was using a USB 2.0 but it was plugged into one of the USB 3.0 ports in the back. I plugged the USB 2.0 into the top and it works!
I don't know what happened to make it stop booting. I had previously tried moving the usb around without luck. The only thing I changed here to get it working again was kwboot with the 2017 version. I did not make that permanent or change any other environment variables. That being said, and according to the log, it's using the 2023 version of uboot again. I'm confused by that but glad it's working again. Thanks for your help!
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 June 05, 2023 06:14PM |
Admin Registered: 13 years ago Posts: 18,545 |
> I don't know what happened to make it stop
> booting. I had previously tried moving the usb
> around without luck. The only thing I changed
> here to get it working again was kwboot with the
> 2017 version. I did not make that permanent or
> change any other environment variables. That
> being said, and according to the log, it's using
> the 2023 version of uboot again. I'm confused by
> that but glad it's working again. Thanks for your
> help!
Cool!
I think we should taking advantage of booting with USB 3.0 rootfs drive in one of the 2 ports in the back. It'll make the rootfs running much faster. I'm running with the Sandisk Ultra Fit (USB 3.0) rootfs and it boots consistently.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> booting. I had previously tried moving the usb
> around without luck. The only thing I changed
> here to get it working again was kwboot with the
> 2017 version. I did not make that permanent or
> change any other environment variables. That
> being said, and according to the log, it's using
> the 2023 version of uboot again. I'm confused by
> that but glad it's working again. Thanks for your
> help!
Cool!
I think we should taking advantage of booting with USB 3.0 rootfs drive in one of the 2 ports in the back. It'll make the rootfs running much faster. I'm running with the Sandisk Ultra Fit (USB 3.0) rootfs and it boots consistently.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: 2023.04 U-Boot Kirkwood - Pogo V4 June 06, 2023 02:46PM |
Registered: 4 years ago Posts: 54 |
@bodhi one last quick question. I noticed a file named uInitr in the boot folder that I've never noticed before. Should that file be there or can it be deleted? I thought I may have left the d off the end when copying and pasting earlier in the upgrade process. Thank you.
root@PogoplugV4:~$ ls -lha /boot/ total 83M drwxr-xr-x 3 root root 4.0K Jun 5 17:38 . drwxr-xr-x 21 root root 4.0K May 30 13:35 .. -rw-r--r-- 1 root root 4.2M May 31 17:51 System.map-6.3.5-kirkwood-tld-1 -rw-r--r-- 1 root root 192K May 31 17:51 config-6.3.5-kirkwood-tld-1 drwxr-xr-x 2 root root 4.0K Apr 29 15:33 dts -rw-r--r-- 1 root root 9.9M Jun 3 12:08 initrd.img-6.3.5-kirkwood-tld-1 -rw-r--r-- 1 root root 161K Jun 1 16:30 linux-6.3.5-kirkwood-tld-1.patch -rw-r--r-- 1 root root 8.1M May 31 19:35 linux-headers-6.3.5-kirkwood-tld-1_1_armel.deb -rw-r--r-- 1 root root 24M May 31 19:35 linux-image-6.3.5-kirkwood-tld-1_1_armel.deb -rw-r--r-- 1 root root 5.9M Jun 3 12:08 uImage -rw-r--r-- 1 root root 9.3M May 30 14:54 uInitr -rw-r--r-- 1 root root 9.9M Jun 3 12:08 uInitrd -rwxr-xr-x 1 root root 5.9M May 31 17:51 vmlinuz-6.3.5-kirkwood-tld-1 -rwxr-xr-x 1 root root 5.9M May 31 19:15 zImage-6.3.5-kirkwood-tld-1
