Who has had success with 3TB GFH? [Solved] December 24, 2012 07:55PM |
Registered: 11 years ago Posts: 20 |
Recovery/transformation command (? for help): p Disk /dev/sda: 5860533168 sectors, 2.7 TiB Logical sector size: 512 bytes Disk identifier (GUID): E6D0FDC0-0A69-47A9-B3DF-672B315FAB76 Partition table holds up to 128 entries First usable sector is 34, last usable sector is 5860533134 Partitions will be aligned on 2048-sector boundaries Total free space is 2014 sectors (1007.0 KiB) Number Start (sector) End (sector) Size Code Name 1 2048 33556479 16.0 GiB 8300 Linux filesystem 2 33556480 5860533134 2.7 TiB 8300 Linux filesystem Recovery/transformation command (? for help): o Disk size is 5860533168 sectors (2.7 TiB) MBR disk identifier: 0x00000000 MBR partitions: Number Boot Start Sector End Sector Status Code 1 * 2048 33556479 primary 0x83 4 1 2047 primary 0xEE
Re: Who has had success with 3TB GFH? [Solved] -- for me too ... January 21, 2013 10:30AM |
Registered: 12 years ago Posts: 157 |
rescue:~# fw_printenv ethact=egiga0 bootdelay=3 baudrate=115200 mainlineLinux=yes console=ttyS0,115200 led_init=green blinking led_exit=green off led_error=orange blinking mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) mtdids=nand0=orion_nand partition=nand0,2 stdin=serial stdout=serial stderr=serial rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi ubifs_mtd=3 ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done usb_scan_list=1 2 3 4 usb_init=run usb_scan usb_device=0:1 usb_root=/dev/sda1 usb_rootdelay=10 usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi ethaddr=XX:XX:XX:XX:XX:XX arcNumber=3338 serverip=192.XXX.XXX.XXX if_netconsole=ping $serverip start_netconsole=setenv ncip $serverip; setenv bootdelay 5; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; preboot=run if_netconsole start_netconsole ipaddr=192.XXX.XXX.XXX usb_scan_1=usb=0:1 dev=sda2 usb_scan_2=usb=1:1 dev=sdb2 usb_scan_3=usb=2:1 dev=sdc2 usb_scan_4=usb=3:1 dev=sdd2 usb_rootfstype=ext4 usb_root_label=USB-Root usb_set_bootargs=setenv bootargs console=$console root=LABEL=$usb_root_label rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params ide_scan=ide_scan_done=0;for scan in $ide_scan_list; do run ide_scan_$scan; if test $ide_scan_done -eq 0 && ext2load ide $ide 0x800000 /boot/uImage 1; then ide_scan_done=1; echo "Found bootable drive on ide $ide"; setenv ide_device $ide; setenv ide_root /dev/$dev; fi; done ide_init=ide reset; run ide_scan ide_scan_list=1 2 ide_scan_1=ide=0:1 dev=sda2 ide_scan_2=ide=1:1 dev=sdb2 ide_rootfstype=ext4 ide_rootdelay=10 ide_set_bootargs=setenv bootargs console=$console root=LABEL=$ide_root_label rootdelay=$ide_rootdelay rootfstype=$ide_rootfstype $mtdparts $ide_custom_params ide_boot=ext2load ide $ide_device 0x800000 /boot/uImage; ext2load ide $ide_device 0x1100000 /boot/uInitrd; run ide_set_bootargs; bootm 0x800000 0x1100000 ide_bootcmd=run ide_init; run ide_boot bootcmd=usb start; usb_stop; usb_start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run ide_bootcmd; run rescue_bootcmd; run pogo_bootcmd; reset rescue_installed=1 ide_root_label=HDD-Root
rescue:~# blkid /dev/sda1: LABEL="HDD-Boot" UUID="f24cd4da-19c5-4868-951a-80dd734211fa" TYPE="ext2" /dev/sda2: LABEL="HDD-Root" UUID="f2cc90ef-6338-4462-a5a7-d98d9e1c6a64" TYPE="ext4" /dev/sda3: UUID="bdc7b7f8-efec-469e-bb1b-40a2ad94bf6d" TYPE="swap" /dev/sda4: UUID="8y8UaH-aHxy-rUhZ-Q2ce-ibda-g8H5-jknncc" TYPE="lvm2pv" rescue:~# gdisk /dev/sda GPT fdisk (gdisk) version 0.8.5 Partition table scan: MBR: hybrid BSD: not present APM: not present GPT: present Found valid GPT with hybrid MBR; using GPT. Command (? for help): r Recovery/transformation command (? for help): p Disk /dev/sda: 5860533168 sectors, 2.7 TiB Logical sector size: 512 bytes Disk identifier (GUID): FA87030F-1005-4B21-B8AA-649C50CFFB55 Partition table holds up to 128 entries First usable sector is 34, last usable sector is 5860533134 Partitions will be aligned on 2048-sector boundaries Total free space is 2014 sectors (1007.0 KiB) Number Start (sector) End (sector) Size Code Name 1 2048 264191 128.0 MiB 8300 Linux filesystem 2 264192 10749951 5.0 GiB 8300 Linux filesystem 3 10749952 11798527 512.0 MiB 8300 Linux filesystem 4 11798528 5860533134 2.7 TiB 8300 Linux filesystem Recovery/transformation command (? for help): o Disk size is 5860533168 sectors (2.7 TiB) MBR disk identifier: 0x00000000 MBR partitions: Number Boot Start Sector End Sector Status Code 1 1 2047 primary 0xEE 2 * 2048 264191 primary 0x83 3 * 264192 10749951 primary 0x83 4 10749952 11798527 primary 0x83
U-Boot 2011.12 (Apr 18 2012 - 23:08:20) Seagate GoFlexNet arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1 GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709 Hit any key to stop autoboot: 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 1 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found Unknown command 'usb_stop' - try 'help' Unknown command 'usb_start' - try 'help' ** Block device usb 0 not supported ** Invalid boot device ** Creating 1 MTD partitions on "nand0": 0x000002500000-0x000010000000 : "mtd=3" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI error: validate_ec_hdr: bad VID header offset 2048, expected 512 UBI error: validate_ec_hdr: bad EC header UBI error: ubi_io_read_ec_hdr: validation failed for PEB 0 UBI error: ubi_init: cannot attach mtd1 UBI error: ubi_init: UBI error: cannot initialize UBI, error -22 UBI init error 22 ** Block device usb 0 not supported ** Block device usb 1 not supported ** Block device usb 2 not supported ** Block device usb 3 not supported ** Block device usb 0 not supported ** Block device usb 0 not supported Wrong Image Format for bootm command ERROR: can't get kernel image! stopping USB.. Reset IDE: Bus 0: OK Bus 1: not available Device 0: Model: ST3000DM001-1CH166 Firm: CC44 Ser#: W1F1P3N3 Type: Hard Disk Supports 48-bit addressing Capacity: 764436.4 MB = 746.5 GB (1565565872 x 512) Loading file "/boot/uImage" from ide device 0:1 (hda1) Failed to mount ext2 filesystem... ** Bad ext2 partition or disk - ide 0:1 ** ** Bad partition 1 ** ** No boot file defined ** ** No boot file defined ** Wrong Image Format for bootm command ERROR: can't get kernel image! NAND read: device 0 offset 0x100000, size 0x400000 4194304 bytes read: OK ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.3.2-kirkwide Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3627768 Bytes = 3.5 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ...
Re: Who has had success with 3TB GFH? [Solved] -- for me too ... February 27, 2013 02:43PM |
Registered: 11 years ago Posts: 10 |