DS418J no ethernet

Hello all,
A friend gave me a DS418J for repair. The ethernet slot is dead, there is no link created and the NAS is not recognized on the network.
I tried :
- hard reset
- with and wiohout hard disk
- 3 cables (all OK...)
- USB adapter to ethernet (not good)

Power LED (blue is ON), but status LED is blinking green.

I add a link to the UART port on the MB for see the boot log, below the result :

hwsetting size: 000006E4
C4
f
5-5
Goto FSBL: 0x10100000
Welcome to FSBL ...
[FSBL] Warm Boot: 0x00000000
[FSBL] Secure: 0x0000BEEE
[FSBL] Flash Type: 0x00000001
[FSBL] DCache Enable: 0x00000000
********** FW_TYPE_BOOTCODE **********
    FW Image to 0x00020000, size=0x000624E0 (0x000824E0)
    FW Image fr 0x88120F80
md copy audio bin
j 64b


U-Boot 2012.07-g4cd3708 (Jan 25 2019 - 11:25:17)

CPU  : Cortex-A53 dual core - AARCH32
Board: Realtek QA Board
DRAM:  1 GiB
Watchdog: Disabled
Cache: Enabled
Non-Cache Region: 1 MB@0x07900000
nor flash id [0x00c22017]
sector 256k en: 0
sector  64k en: 1
sector  32k en: 0
sector   4k en: 1
page_program  : 1
max capacity  : 0x00800000
spi type name : MX 64Mbit
Factory: NOR
Factory: pp:0, seq#:0x37, size:0x200
------------can't find tmp/factory/000BootParam.h
[ENV] read_env from factory failed
[ENV] Using default environment variables

In:    serial
Out:   serial
Err:   serial
RTK_set_power_saving_config:Default POWERE_ON_S5 not set

Synology Model: DS418j

SYNO_CTRL_FAN_PERSISTER Pin not implement
SYNO_CTRL_FAN_PERSISTER Pin not implement
SYNO_CTRL_FAN_PERSISTER Pin not implement
SYNO_CTRL_FAN_PERSISTER Pin not implement
SYNO_CTRL_FAN_PERSISTER Pin not implement
SYNO_CTRL_FAN_PERSISTER Pin not implement
Net:   Realtek PCIe GBE Family Controller mcfg = 0024
dev->name=r8168#0
*** Reboot-Action invalid ***
Hit Esc or Tab key to enter console mode or rescue linux:  0
------------can't find tmp/factory/recovery
======== Checking into android recovery ====

check_acpu_boot_notification, boot-reason : 0x00480488
check_rtc_expire:RTC not detected in factory
customize_check_normal_boot: power up by button

SPI start addr(remap) = 0x88200000
DDR start addr        = 0x0b000000
reading byte size     = 0x002f0000
Uncompressed size: 8459080 = 0x811348

SPI start addr(remap) = 0x881c0000
DDR start addr        = 0x0b000000
reading byte size     = 0x00040000
Uncompressed size: 785544 = 0xBFC88

SPI start addr(remap) = 0x88100000
DDR start addr        = 0x01f00000
reading byte size     = 0x00010000

SPI start addr(remap) = 0x884f0000
DDR start addr        = 0x02200000
reading byte size     = 0x003ff000
Start Boot Setup ...
Start Audio Firmware ...
Start A/V Firmware ...
[bonding] 1295 chip
create_1293_thread
ClassifyBonding  0x00000810, num =  0x00000001 PN_VA1 (PN_VA1)
[FW]kylin_bring up hwsetting
Finish kylin_bring_temp hwsetting
[ACPU]: Set protect 6 fail, protect 6 is already enable : 0x00000040!!

HDMI Raw Enable: AC3 DTS MPEG2 AAC DDP

SPDIF Raw Enable: AC3 DTS MPEG2 AAC

Force 2ch Format: DTS DTSHD AC3 DDP MLP AAC WMAPRO


@@@@@@@One Step TV System magic number = 0xffffffff, addr = 0xa001f800@@@@@@@

@@@@One Step magic number not match! use fw default TV System!
HDMIOff = 0
[VO]vo->is_hdmi_off_clock_on:0
[VO_SetVideoStandard]st 25 p 1 1 0
[VO_SetVideoStandard]dp_standard:1067002368 data0  0x00000004 data1  0x00000000
[VO_SetVideoStandard]HDMIoff 0 is_tve_on 0 user_cvbs_off 1
lvds.format 0 port_setting  0x00000381 lvds_wb 0
[VO setTVStandard 25 3D 0 0]

(TVE) TVE_DAC_mode 0,cmd->enProg 1!!
~~comp 0, ch2 0, mode_3D 0!!
SetVideoStandard return!

(VO_ConfigHDMI_InfoFrame) L:264, is_hdmi_plugin 1, hdmiMode 1!!Mode 1 dataByte1  0x00000040  0x000000a8  0x00000000
dataByte4  0x00000000  0x00000000 int0  0x00000001

(HDMI_3D) mode 1, HDMI_gen 1, En_3D 0, Format_3D 0 scramble:0!!RGB_or_YCbCr:2 Pixel_Colocrt:2 Deep_Color:0 Deep_Depth:0
@@vo->hdr_ctrl.trans:0 HDMI_gen_dynamic_range_master_infoframe
@@set C1C0 to 2(BT709),set EC2EC1EC0 to 0

 go back SET_HDMI!!boot_info  0xa0000000 magic  0xbccbffff en 233


EXPORT ENV AT 0x10000000, ENV size info:0x00002000,0x00001ffc,0x00000004
rtk_preload_bootimages_spi : header info
 0x00000700 0x000624c0 0x0000fac0 0x00000000
 0x00000000 0x00000000 0x00000000 0x00026320
 0x00000000
rtk_preload_bootimages_spi : load U-Boot 64 from 0x88192f40 to 0x01500000 with size 0x00026320
copy_2nd_bootloader_and_run : src:0x01500000, dst:0x00021000, size:0x00028000
Jumping to 2nd bootloader...


U-Boot 2015.07-g428cfe7-dirty (May 16 2018 - 10:33:51 +0800)

CPU  : Cortex-A53 Quad Core
Board: Realtek QA Board
DRAM:  1 GiB
mapping memory 0x20000000-0x40000000 non-cached
In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  0
rtk_plat_set_fw not port yet, use default configs
## Flattened Device Tree blob at 01f00000
   Booting using the fdt blob at 0x1f00000
   reserving fdt memory region: addr=2200000 size=3ff000
   reserving fdt memory region: addr=0 size=30000
   reserving fdt memory region: addr=1f000 size=1000
   reserving fdt memory region: addr=1b00000 size=400000
   reserving fdt memory region: addr=1ffe000 size=4000
   reserving fdt memory region: addr=10000000 size=14000
   Using Device Tree in place at 0000000001f00000, end 0000000001f108ba
Bring UP slave CPUs

Starting Kernel ...


[ROS: openRPC() intr_scpu_dev_r buf  0x00e2ffa1 s  0x00e2ffa1 e  0x00e4ffa1 i  0x00e2ffa1
[ROS: openStubRPC() intr_w buf  0x00e6ffa1 s  0x00e6ffa1 e  0x00e8ffa1 i  0x00e6ffa1[AVCPU] Set Debug level flag  0x81bce334 *flag  0x01bbfde4 ucache  0xa1bbfde4
[AVCPU] Set Debug level *ptrDebugFlag  0x00000001
-------------------
Audio Version = 1012363 (Kylin)
Common Version = 0
Binary src compiled at Mar 21 2017 00:20:22
Note =
-------------------




[A] gloabl malloc size  0x003ffeb8
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.4.59+ (root@build5) (gcc version 4.9.4 20150629 (prerelease) (crosstool-NG crosstool-ng-1.22.0-169-g87eb166) ) #25556 SMP Fri Aug 16 14:54:00 CST 2024
[    0.000000] Boot CPU: AArch64 Processor [410fd034]
[    0.000000] cma: Reserved 32 MiB at 0x000000003e000000
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv0.1 detected in firmware.
[    0.000000] psci: Conflicting PSCI version detected.
[    0.000000] PERCPU: Embedded 15 pages/cpu @ffffffc03df9d000 s24576 r8192 d28672 u61440
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: enabling workaround for ARM erratum 845719
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 258048
[    0.000000] Kernel command line: ip=off console=ttyS0,115200 root=/dev/md0 rw syno_hdd_detect=4,5,6,7 syno_hdd_enable=85,86,82,81 HddHotplug=4 syno_usb_vbus_gpio=23@xhci-hcd.2.auto@0,22@xhci-hcd.5.auto@0 syno_hw_version=DS418j hd_power_on_seq=4 ihd_num=4 netif_num=1 swiotlb=1 audio_version=1012363 syno_fw_version=M.103 U-boot=2012.07-g4cd3708 (Jan 25 2019 - 11:25:17)
[    0.000000] SYNO GPIO hdd detect pin: 4 5 6 7
[    0.000000] SYNO GPIO hdd enable pin: 85 86 82 81
[    0.000000] Support HDD Hotplug.
[    0.000000] USB Vbus GPIO Control:
[    0.000000]  Gpp#23 - Host: xhci-hcd.2.auto      - Port:1 - Polarity: ACTIVE_HIGH
[    0.000000]  Gpp#22 - Host: xhci-hcd.5.auto      - Port:1 - Polarity: ACTIVE_HIGH
[    0.000000] Synology Hardware Version: DS418j
[    0.000000] Internal HD num: 4
[    0.000000] Internal netif num: 1
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[    0.000000] software IO TLB [mem 0x3ddd5000-0x3de15000] (0MB) mapped at [ffffffc03ddd5000-ffffffc03de14fff]
[    0.000000] Memory: 973920K/1048576K available (5536K kernel code, 324K rwdata, 2072K rodata, 264K init, 486K bss, 41888K reserved, 32768K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vmalloc : 0xffffff8000000000 - 0xffffffbdbfff0000   (   246 GB)
[    0.000000]     vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000   (     8 GB maximum)
[    0.000000]               0xffffffbdc0000000 - 0xffffffbdc1000000   (    16 MB actual)
[    0.000000]     fixed   : 0xffffffbffa7fd000 - 0xffffffbffac00000   (  4108 KB)
[    0.000000]     PCI I/O : 0xffffffbffae00000 - 0xffffffbffbe00000   (    16 MB)
[    0.000000]     modules : 0xffffffbffc000000 - 0xffffffc000000000   (    64 MB)
[    0.000000]     memory  : 0xffffffc000000000 - 0xffffffc040000000   (  1024 MB)
[    0.000000]       .init : 0xffffffc0009ef000 - 0xffffffc000a31000   (   264 KB)
[    0.000000]       .text : 0xffffffc000280000 - 0xffffffc0009eebb4   (  7611 KB)
[    0.000000]       .data : 0xffffffc000a40000 - 0xffffffc000a91280   (   325 KB)
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  CONFIG_RCU_FANOUT set to non-default value of 32
[    0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:64 nr_irqs:64 0
[    0.000000] Architected cp15 timer(s) running at 27.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x63a1e71a3, max_idle_ns: 440795203123 ns
[    0.000005] sched_clock: 56 bits at 27MHz, resolution 37ns, wraps every 4398046511093ns
[    0.000089] [RTK-TIMER0] set mode: CLOCK_EVT_MODE_SHUTDOWN
[    0.000100] [RTK-TIMER0] clocksource 0 register HZ
[    0.000110] clocksource: rtk_timer0_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 70787423951 ns
[    0.000164] [RTK-TIMER0] set mode: CLOCK_EVT_MODE_SHUTDOWN
[    0.000174] [RTK-TIMER1] set mode: CLOCK_EVT_MODE_SHUTDOWN
[    0.000183] [RTK-TIMER1] clocksource 1 register HZ
[    0.000193] clocksource: rtk_timer1_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 579169832313 ns
[    0.000539] [RTK_MEM_REMAP] initialized
[    0.000778] Calibrating delay loop (skipped), value calculated using timer frequency.. 54.00 BogoMIPS (lpj=270000)
[    0.000791] pid_max: default: 32768 minimum: 301
[    0.000929] Security Framework initialized
[    0.000954] AppArmor: AppArmor initialized
[    0.001013] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[    0.001024] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[    0.001726] Initializing cgroup subsys io
[    0.001744] Initializing cgroup subsys memory
[    0.001780] Initializing cgroup subsys devices
[    0.001793] Initializing cgroup subsys freezer
[    0.002095] ASID allocator initialised with 65536 entries
[    0.010125] pctrl-rtk: addr: 0x0002800c [0x13de8161 -> 0x135e8161], bit-diff = 0x00800000, mask = 0x28a03012
[    0.010156] pctrl-rtk: addr: 0x0002a010 [0x5801e416 -> 0x58010414], bit-diff = 0x0000e002, mask = 0x0100e0a2
[    0.010183] pctrl-rtk: addr: 0x0002c08c [0x00001f01 -> 0x00001901], bit-diff = 0x00000600, mask = 0x000006f8
[    0.010211] pctrl-rtk: addr: 0x0002e000 [0xb7d01001 -> 0x97d01001], bit-diff = 0x20000000, mask = 0x68000354
[    0.010238] pctrl-rtk: addr: 0x00030004 [0x1f840e01 -> 0x0f840e01], bit-diff = 0x10000000, mask = 0x507be1fc
[    0.010264] pctrl-rtk: addr: 0x00032050 [0x0000801f -> 0x0000801f], bit-diff = 0x00000000, mask = 0x00007020
[    0.010296] pctrl-rtk: addr: 0x00034088 [0x00001f80 -> 0x00001f80], bit-diff = 0x00000000, mask = 0x00002062
[    0.010353] pctrl-rtk: pctrl_ve1::POWER_OFF, ret = 0
[    0.010432] pctrl-rtk: pctrl_ve2::POWER_OFF, ret = 0
[    0.010503] pctrl-rtk: pctrl_ve3::POWER_OFF, ret = 0
[    0.010576] pctrl-rtk: pctrl_l4_icg_jpeg::ENABLE_HW_PM, ret = -1
[    0.010639] pctrl-rtk: pctrl_gpu::POWER_OFF, ret = 0
[    0.010724] pctrl-rtk: pctrl_gpu_core_1::POWER_OFF, ret = 0
[    0.010805] pctrl-rtk: pctrl_gpu_core_2::POWER_OFF, ret = 0
[    0.010895] pctrl-rtk: pctrl_gpu_core_3::POWER_OFF, ret = 0
[    0.011018] pctrl-rtk: pctrl_l4_icg_vo::ENABLE_HW_PM, ret = 0
[    0.011089] pctrl-rtk: pctrl_l4_icg_aio::ENABLE_HW_PM, ret = -1
[    0.011470] pctrl-rtk: pctrl_audio_dac::POWER_OFF, ret = 0
[    0.011592] pctrl-rtk: pctrl_video_dac::POWER_OFF, ret = 0
[    0.011657] pctrl-rtk: pctrl_mhl3_en::POWER_OFF, ret = 0
[    0.011716] pctrl-rtk: pctrl_l4_icg_se::ENABLE_HW_PM, ret = 0
[    0.011777] pctrl-rtk: pctrl_l4_icg_mipi::ENABLE_HW_PM, ret = -1
[    0.011908] pctrl-rtk: pctrl_mipi_aphy::POWER_OFF, ret = 0
[    0.012553] pctrl-rtk: pctrl_l4_icg_nand::ENABLE_HW_PM, ret = -1
[    0.012614] pctrl-rtk: pctrl_usb_p0_mac::POWER_ON, ret = 0
[    0.012675] pctrl-rtk: pctrl_usb_p0_phy::POWER_ON, ret = 0
[    0.012861] pctrl-rtk: pctrl_usb_p3_mac_A: rev not match
[    0.012904] pctrl-rtk: pctrl_usb_p3_mac::POWER_ON, ret = 0
[    0.012960] pctrl-rtk: pctrl_usb_p3_phy::POWER_ON, ret = 0
[    0.013223] pctrl-rtk: pctrl_cr::POWER_OFF, ret = 0
[    0.013352] pctrl-rtk: pctrl_sdio::POWER_OFF, ret = 0
[    0.013757] pctrl-rtk: pctrl_pll_ve1::POWER_OFF, ret = 0
[    0.014788] Detected VIPT I-cache on CPU1
[    0.014831] CPU1: Booted secondary processor [410fd034]
[    0.014903] Brought up 2 CPUs
[    0.014919] SMP: Total of 2 processors activated.
[    0.014931] CPU: All CPU(s) started at EL2
[    0.014951] alternatives: patching kernel code
[    0.015493] devtmpfs: initialized
[    0.028504] clk-rtk: scpu,pll,workaround 34055501
[    0.028513] clk-rtk: scpu,pll,workaround 04038500
[    0.033636] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.033666] futex hash table entries: 512 (order: 4, 65536 bytes)
[    0.035187] xor: measuring software checksum speed
[    0.129886]    8regs     :  1153.200 MB/sec
[    0.229945]    8regs_prefetch:  1086.800 MB/sec
[    0.330001]    32regs    :  1318.800 MB/sec
[    0.430061]    32regs_prefetch:  1188.800 MB/sec
[    0.430069] xor: using function: 32regs (1318.800 MB/sec)
[    0.430097] pinctrl core: initialized pinctrl subsystem
[    0.430960] NET: Registered protocol family 16
[    0.432596] vdso: 2 pages (1 code @ ffffffc000a45000, 1 data @ ffffffc000a44000)
[    0.432640] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.433680] DMA: preallocated 1024 KiB pool for atomic allocations
[    0.434107] rst-control : base ffffff8000454600, offset 0x40
[    0.434133] ****** rtk_lockapi_init 566, chip_revision = 0x00010000
[    0.434339] [PINCTRL] driver init
[    0.437423] [PINCTRL] init done
[    0.650409] raid6: int64x1  gen()   221 MB/s
[    0.820518] raid6: int64x1  xor()   235 MB/s
[    0.990674] raid6: int64x2  gen()   330 MB/s
[    1.160711] raid6: int64x2  xor()   302 MB/s
[    1.330794] raid6: int64x4  gen()   494 MB/s
[    1.500974] raid6: int64x4  xor()   372 MB/s
[    1.671048] raid6: int64x8  gen()   585 MB/s
[    1.841193] raid6: int64x8  xor()   374 MB/s
[    2.011376] raid6: neonx1   gen()   365 MB/s
[    2.181437] raid6: neonx1   xor()   383 MB/s
[    2.351540] raid6: neonx2   gen()   567 MB/s
[    2.521695] raid6: neonx2   xor()   508 MB/s
[    2.691813] raid6: neonx4   gen()   755 MB/s
[    2.861947] raid6: neonx4   xor()   590 MB/s
[    3.032037] raid6: neonx8   gen()   839 MB/s
[    3.202156] raid6: neonx8   xor()   619 MB/s
[    3.202163] raid6: using algorithm neonx8 gen() 839 MB/s
[    3.202170] raid6: .... xor() 619 MB/s, rmw enabled
[    3.202177] raid6: using intx1 recovery algorithm
[    3.202245] ACPI: Interpreter disabled.
[    3.202326] [RTD129x_PM] Initial RTD129x Power Management Driver.
[    3.202916] [RTD129x_PM] wakeup-gpio Cnt: en(1) act(1) list(1)
[    3.202971] [RTD129x_PM] wakeup-gpio[0] Successful registration! (en:1 act:0 gpio:124)
[    3.202983] [RTD129x_PM] gpio-output-change Cnt: en(0) act(0) list(-2)
[    3.202991] [RTD129x_PM] Set suspend-mode = ram
[    3.202999] [RTD129x_PM] Wakeup Flags Set Default : 0x2d
[    3.203371] SCSI subsystem initialized
[    3.203711] rtk-usb-power-manager 98000000.rtk_usb_power_manager: ENTER rtk_usb_power_manager_probe
[    3.203839] rtk-usb-power-manager 98000000.rtk_usb_power_manager: rtk_dwc3_drd status is okay
[    3.203854] rtk-usb-power-manager 98000000.rtk_usb_power_manager: ehci status is okay
[    3.203865] rtk-usb-power-manager 98000000.rtk_usb_power_manager: ohci status is okay
[    3.203876] rtk-usb-power-manager 98000000.rtk_usb_power_manager: rtk_dwc3_u3host status is okay
[    3.203900] rtk-usb-power-manager 98000000.rtk_usb_power_manager: set usb_power_domain/p3 on
[    3.209977] rtk-usb-power-manager 98000000.rtk_usb_power_manager: rtk_usb_power_manager_probe OK (take 0 ms)
[    3.212711] clocksource: Switched to clocksource arch_sys_counter
[    3.213224] AppArmor: AppArmor Filesystem Enabled
[    3.213305] pnp: PnP ACPI: disabled
[    3.215044] NET: Registered protocol family 2
[    3.215580] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    3.215719] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
[    3.215962] TCP: Hash tables configured (established 8192 bind 8192)
[    3.216024] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    3.216071] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    3.216312] NET: Registered protocol family 1
[    3.216636] RPC: Registered named UNIX socket transport module.
[    3.216645] RPC: Registered udp transport module.
[    3.216652] RPC: Registered tcp transport module.
[    3.216659] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    3.216883] Trying to unpack rootfs image as initramfs...
[    7.011196] Freeing initrd memory: 4092K (ffffffc002200000 - ffffffc0025ff000)
[    7.011945] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[    7.014381] audit: initializing netlink subsys (disabled)
[    7.014432] audit: type=2000 audit(7.009:1): initialized
[    7.014877] Initialise system trusted keyring
[    7.025944] VFS: Disk quotas dquot_6.6.0
[    7.026015] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    7.030013] NFS: Registering the id_resolver key type
[    7.030050] Key type id_resolver registered
[    7.030058] Key type id_legacy registered
[    7.102076] Key type asymmetric registered
[    7.102096] Asymmetric key parser 'x509' registered
[    7.102232] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    7.102249] io scheduler noop registered
[    7.102262] io scheduler deadline registered
[    7.102300] io scheduler cfq registered (default)
[    7.102615] [RTD129x PCIE Slot2] 9803b000.pcie2: PCIE host driver initial begin.
[    7.102628] [RTD129x PCIE Slot2] 9803b000.pcie2: Speed Mode: GEN2
[    7.102751] [RTD129x PCIE Slot2] 9803b000.pcie2: can't request 'DCSYS_BASE' address, no init msi
[    7.272773] [RTD129x PCIE Slot2] 9803b000.pcie2: PCIE device has link up in slot 2
[    7.272792] PCI host bridge /pcie2@9803B000 ranges:
[    7.272820]   MEM 0xc1000000..0xc1ffffff -> 0xc1000000
[    7.272833]    IO 0x00040000..0x0004ffff -> 0x00040000
[    7.273050] [RTD129x PCIE Slot2] 9803b000.pcie2: PCI host bridge to bus 0001:01
[    7.273067] pci_bus 0001:01: root bus resource [bus 00-ff]
[    7.273080] pci_bus 0001:01: root bus resource [mem 0xc1000000-0xc1ffffff]
[    7.273095] pci_bus 0001:01: root bus resource [io  0x0000-0xffff] (bus address [0x40000-0x4ffff])
[    7.273189] pci 0001:01:00.0: syno quirk detected Vendor ID:0x1b21, Device ID:0x0612; MSI disabled
[    7.273216] pci 0001:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[    7.273246] pci 0001:01:00.0: reg 0x14: initial BAR value 0x00000000 invalid
[    7.273276] pci 0001:01:00.0: reg 0x18: initial BAR value 0x00000000 invalid
[    7.273305] pci 0001:01:00.0: reg 0x1c: initial BAR value 0x00000000 invalid
[    7.273335] pci 0001:01:00.0: reg 0x20: initial BAR value 0x00000000 invalid
[    7.273829] pci 0001:01:00.0: BAR 6: assigned [mem 0xc1000000-0xc100ffff pref]
[    7.273846] pci 0001:01:00.0: BAR 5: assigned [mem 0xc1010000-0xc10101ff]
[    7.273864] pci 0001:01:00.0: BAR 4: assigned [io  0x1000-0x101f]
[    7.273881] pci 0001:01:00.0: BAR 0: assigned [io  0x1020-0x1027]
[    7.273897] pci 0001:01:00.0: BAR 2: assigned [io  0x1028-0x102f]
[    7.273913] pci 0001:01:00.0: BAR 1: assigned [io  0x1030-0x1033]
[    7.273929] pci 0001:01:00.0: BAR 3: assigned [io  0x1034-0x1037]
[    7.273968] [RTD129x PCIE Slot2] 9803b000.pcie2: PCIE host driver initial done.
[    7.275052] [SB2 DBG][sb2_dbg_init] memory monitor 0x98013b00 - 0x98013c00
[    7.275062] [SB2 DBG][sb2_dbg_init] initialized
[    7.275351] rpc is not paused & suspended
[    7.282851] rpc_int_base:ffffff8000498104 irq:18
[    7.283060] [PUWRAP] begin pu_init
[    7.283070] [PUWRAP] end pu_init result=0x0
[    7.283750] memalloc: Linear Memory Allocator
[    7.284173] jpu_init
[    7.284181] end jpu_init result=0x0
[    7.284364] misc rtk_lockapi: registered.
[    7.388529] AudioIntrRead:143 can't find process for handling AudioIntrRead programID:98
[    7.388550] AudioIntrRead: program:98 version:0 procedure:1 taskID:0 sysTID:4294967295 sysPID:4294967295 size:4 context:81bcc245 atomic
[    7.502699] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    7.504428] ####1 p->uartclk:27000000
[    7.504474] ####3 p->uartclk:27000000
[    7.504722] console [ttyS0] disabled
[    7.504771] 98007800.serial0: ttyS0 at MMIO 0x98007800 (irq = 194, base_baud = 1687500) is a 16550A
[    8.988100] console [ttyS0] enabled
[    8.992148] ####1 p->uartclk:432000000
[    8.996070] ####3 p->uartclk:432000000
[    9.000237] 9801b200.serial1: ttyS1 at MMIO 0x9801b200 (irq = 163, base_baud = 27000000) is a 16550A
[    9.034757] brd: module loaded
[    9.104065] Loading iSCSI transport class v2.0-870.
[    9.253131] ahci 0001:01:00.0: enabling device (0000 -> 0003)
[    9.259107] ahci 0001:01:00.0: SSS flag set, parallel bus scan disabled
[    9.266006] ahci 0001:01:00.0: AHCI 0001.0200 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
[    9.274330] ahci 0001:01:00.0: flags: 64bit ncq sntf stag led clo pmp pio slum part ccc sxs
[    9.283020] ahci 0001:01:00.0: Asmedia 1061 port=0, reg_addr=0xca6, reg_data=0xaf
[    9.290697] ahci 0001:01:00.0: Asmedia 1061 port=1, reg_addr=0xda6, reg_data=0xaf
[    9.556002] scsi host0: ahci
[    9.581641] scsi host1: ahci
[    9.587805] ata1: SATA max UDMA/133 abar m512@0xc1010000 port 0xc1010100 irq 21
[    9.595361] ata2: SATA max UDMA/133 abar m512@0xc1010000 port 0xc1010180 irq 21
[    9.952765] ata1: SATA link down (SStatus 0 SControl 300)
[    9.958313] ata1: Disk is not present for SATA link down event
[   10.312752] ata2: SATA link down (SStatus 0 SControl 300)
[   10.318288] ata2: Disk is not present for SATA link down event
[   10.345410] [SATA] spread-spectrum disable
[   10.391626] [SATA] set tx-driving to L (level 8)
[   10.428379] [SATA] spread-spectrum disable
[   10.474584] [SATA] set tx-driving to L (level 8)
[   10.491405] ahci_rtk 9803f000.sata: masking port_map 0x3 -> 0x3
[   10.497551] ahci_rtk 9803f000.sata: AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[   10.506660] ahci_rtk 9803f000.sata: flags: ncq sntf pm led clo only pmp fbs pio slum part ccc sadm sds apst
[   10.516745] ahci_rtk 9803f000.sata: port 0 is not capable of FBS
[   10.523297] ahci_rtk 9803f000.sata: port 1 is not capable of FBS
[   10.538354] scsi host2: ahci_rtk
[   10.557930] scsi host3: ahci_rtk
[   10.561722] ata3: SATA max UDMA/133 mmio [mem 0x9803f000-0x9803ffff] port 0x100 irq 12
[   10.569892] ata4: SATA max UDMA/133 mmio [mem 0x9803f000-0x9803ffff] port 0x180 irq 12
[   10.922743] ata3: SATA link down (SStatus 0 SControl 300)
[   10.928289] ata3: Disk is not present for SATA link down event
[   11.282729] ata4: SATA link down (SStatus 0 SControl 300)
[   11.288264] ata4: Disk is not present for SATA link down event
[   11.300007] RtkSFC MTD init ...
[   11.303269] NOR flash support list ..
[   11.307022] (X) HWSEMA support.
[   11.310241] (V) AUTO_HW_POLL support.
[   11.314008] (X) 4Bytes mode support.
[   11.317672] (X) Max erase size support.
[   11.321602] (V) Sfc_delay support.
[   11.325099] (X) Multi-read support.
[   11.341808] --RDID Seq: 0xc2 | 0x20 | 0x17
[   11.346102] *byte1=0xc2
[   11.348755] *byte2=0x16
[   11.351350] RtkSFC MTD: MXIC MX25L6445E detected....
[   11.356449] SFC_4KB_ERASE
[   11.359138] Supported Erase Size: 64KB 32KB 4KB.
[   11.363880] RtkSFC MTD: Enable RtkSFC MD PP callback function.
[   11.369855] MD_READ Enable..
[   11.372816] MD_WRITE Enable..
[   11.375912] [rtk_sfc_attach]descriptor size 0x800000
[   11.412494] Searching for RedBoot partition table in RtkSFC at offset 0x7ff000
[   11.423991] 5 RedBoot partitions found on MTD device RtkSFC
[   11.429701] Rtk SFC: using dynamic partition
[   11.434088] Creating 5 MTD partitions on "RtkSFC":
[   11.439002] 0x000000000000-0x000000100000 : "RedBoot"
[   11.447703] 0x000000100000-0x0000003f0000 : "zImage"
[   11.459579] 0x0000003f0000-0x0000007ef000 : "rd.gz"
[   11.468954] 0x0000007ef000-0x0000007ff000 : "vendor"
[   11.500944] vender Mac0 address : 00:11:32:97:53:d9
[   11.505987] vender Mac1 doesn't set ucSum:0x00 Buf:0x00 Sum:0.
[   11.511966] vender Mac2 doesn't set ucSum:0x00 Buf:0x00 Sum:0.
[   11.517958] vender Mac3 doesn't set ucSum:0x00 Buf:0x00 Sum:0.
[   11.523950] serial number='1880PUN013504'
[   11.545961] 0x0000007ff000-0x000000800000 : "FIS directory"
[   11.568866] Rtk SFC: (for SST/SPANSION/MXIC SPI Flash)
[   11.597705] Realtek SFC Driver is successfully installing.
[   11.597705]
[   11.639380] r8169 Gigabit Ethernet driver 2.32.5-LK-NAPI loaded
[   11.673722] r8169 98016000.gmac eth0: RTL8169SOC at 0xffffff80005a6000, 00:10:20:30:40:50, XID 10900800 IRQ 11
[   11.684018] r8169 98016000.gmac eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[   11.719526] rtk_rbus_init:89
[   11.722652] rtk_rbus_probe:27
[   11.725966] [Ethernet] Watch link status change.
[   11.731664] rtk_refclk_init:89
[   11.735149] rtk_refclk_probe:27
[   11.747287] rtk_md_probe: res.start=0x000000009800b000 res.end=0x000000009800bfff
[   11.755000] rtk_md_probe: mem[0] phys:0x000000009800b000 virt:0xffffff80005ae000 size:0x1000 type:1 name:MD reg space
[   11.776910] rtk_md_probe: mem[1] phys:0x000000003e117000 virt:0xffffff80005b0000 size:0x1000 type:1 name:MD driver data
[   11.798303] rtk_md_probe: mem[2] phys:0x000000003e118000 virt:0xffffff80005b2000 size:0x4000 type:1 name:MD command queue
[   11.809716] rtk_md_probe: irq=20
[   11.813412] Engine[0] Ctrl:0000000c Base:3e118000 ReadPtr:3e118000 WritePtr:3e118000 Limit:3e11c000
[   11.823115] rtc_rtd129x 9801b600.rtc: rtk_rtc already enabled
[   11.829464] rtc_rtd129x 9801b600.rtc: rtc core: registered rtc as rtc0
[   11.840691] i2c /dev entries driver
[   11.847155] md: linear personality registered for level -1
[   11.861699] md: raid0 personality registered for level 0
[   11.876374] md: raid1 personality registered for level 1
[   11.881837] md: raid10 personality registered for level 10
[   11.890176] md: raid6 personality registered for level 6
[   11.895677] md: raid5 personality registered for level 5
[   11.901123] md: raid4 personality registered for level 4
[   11.907379] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[   11.916441] cpufreq: freq_table: frequency-table,rev1:
[   11.921712] cpufreq:  0 .volidx = 0 .freq =  300000
[   11.926813] cpufreq:  1 .volidx = 0 .freq =  400000
[   11.931900] cpufreq:  2 .volidx = 0 .freq =  500000
[   11.936994] cpufreq:  3 .volidx = 2 .freq =  600000
[   11.942079] cpufreq:  4 .volidx = 3 .freq =  700000
[   11.947172] cpufreq:  5 .volidx = 4 .freq =  800000
[   11.952259] cpufreq:  6 .volidx = 5 .freq =  900000
[   11.957353] cpufreq:  7 .volidx = 6 .freq = 1000000
[   11.962438] cpufreq:  8 .volidx = 8 .freq = 1100000
[   11.967531] cpufreq:  9 .volidx = 10 .freq = 1200000
[   11.972714] cpufreq: 10 .volidx = 12 .freq = 1300000
[   11.977889] cpufreq: 11 .volidx = 13 .freq = 1400000
[   11.983074] cpufreq: volt_table: voltage-table:
[   11.987717] cpufreq: 0 .vdd_min =  800000 .vdd_max =  800000
[   11.993690] cpufreq: 1 .vdd_min =  812500 .vdd_max =  812500
[   11.999578] cpufreq: 2 .vdd_min =  825000 .vdd_max =  825000
[   12.005484] cpufreq: 3 .vdd_min =  850000 .vdd_max =  850000
[   12.011370] cpufreq: 4 .vdd_min =  875000 .vdd_max =  875000
[   12.017270] cpufreq: 5 .vdd_min =  900000 .vdd_max =  900000
[   12.023165] cpufreq: 6 .vdd_min =  925000 .vdd_max =  925000
[   12.029052] cpufreq: 7 .vdd_min =  950000 .vdd_max =  950000
[   12.034946] cpufreq: 8 .vdd_min =  962500 .vdd_max =  962500
[   12.040832] cpufreq: 9 .vdd_min =  975000 .vdd_max =  975000
[   12.046725] cpufreq: 10 .vdd_min = 1012500 .vdd_max = 1012500
[   12.052700] cpufreq: 11 .vdd_min = 1025000 .vdd_max = 1025000
[   12.058683] cpufreq: 12 .vdd_min = 1062500 .vdd_max = 1062500
[   12.064665] cpufreq: 13 .vdd_min = 1100000 .vdd_max = 1100000
[   12.070661] cpufreq: volt_table: l2-voltage-table:
[   12.075693] cpufreq: 0 .vdd_min =  900000 .vdd_max =  900000
[   12.081581] cpufreq: 1 .vdd_min =  900000 .vdd_max =  900000
[   12.087503] cpufreq: 2 .vdd_min =  900000 .vdd_max =  900000
[   12.093415] cpufreq: 3 .vdd_min =  900000 .vdd_max =  900000
[   12.099303] cpufreq: 4 .vdd_min =  900000 .vdd_max =  900000
[   12.105210] cpufreq: 5 .vdd_min =  900000 .vdd_max =  900000
[   12.111096] cpufreq: 6 .vdd_min =  900000 .vdd_max =  900000
[   12.116998] cpufreq: 7 .vdd_min =  900000 .vdd_max =  900000
[   12.122894] cpufreq: 8 .vdd_min =  900000 .vdd_max =  900000
[   12.128782] cpufreq: 9 .vdd_min =  900000 .vdd_max =  900000
[   12.134681] cpufreq: 10 .vdd_min =  950000 .vdd_max =  950000
[   12.140656] cpufreq: 11 .vdd_min =  950000 .vdd_max =  950000
[   12.146642] cpufreq: 12 .vdd_min = 1000000 .vdd_max = 1000000
[   12.152617] cpufreq: 13 .vdd_min = 1000000 .vdd_max = 1000000
[   12.176795] NET: Registered protocol family 17
[   12.181417] Key type dns_resolver registered
[   12.186404] registered taskstats version 1
[   12.191698] Loading compiled-in untrusted X.509 certificates
[   12.199566] Loading compiled-in X.509 certificates
[   12.205431] Loaded X.509 cert 'Synology SDG kernel module signing key: 7bd0b0d6bcd31651c22ce3978bdc8c8bdc417329'
[   12.218052] Loaded X.509 cert 'Synology Root Certification Authority: f2c075361f168425f8b5ef31b796406c3aab2089'
[   12.228427] Loaded X.509 cert 'Synology Kernel Module Signing Certification Authority: 600839b5d127e0e11d817a31f0575d323a7c0e28'
[   12.240290] Loaded X.509 cert 'Synology kernel module signing key: 4646ce54489669338118a3b1286da156ac366fa5'
[   12.250382] page_owner is disabled
[   12.253942] AppArmor: AppArmor sha1 policy hashing enabled
[   12.259810] scpu wrappee irq 16, scpu_wrap_addr 0xffffff80005e2000
[   12.259810]
[   12.268569] [SCPU_WRAPPER] initialized
[   12.272407] [SCPU_WRAPPER][scpu_wrapper_init] memory monitor 0x98013b00 - 0x98013c00
[   12.280532] rtc_rtd129x 9801b600.rtc: setting system clock to 2025-09-30 11:31:11 UTC (1759231871)
[   12.296503] thermal thermal_zone0: current temp is 47 C
[   12.301978] thermal cooling_device0: thermal-cpufreq-0 bind to TP0: 1 -> 6, ret = 0
[   12.309866] thermal cooling_device0: thermal-cpufreq-0 bind to TP1: 7 -> 11, ret = 0
[   12.323941] corectrl: token_owenr X -> cpufreq
[   12.331049] dcdc1: disabling
[   12.334073] dcdc2: disabling
[   12.337022] dcdc3: disabling
[   12.339971] dcdc5: disabling
[   12.342926] dcdc6: disabling
[   12.345875] ldo2: disabling
[   12.348734] ldo3: disabling
[   12.351936] Freeing unused kernel memory: 264K (ffffffc0009ef000 - ffffffc000a31000)
[   12.359890] Freeing alternatives memory: 40K (ffffffc000a31000 - ffffffc000a3b000)
START /linuxrc.syno
Insert basic USB modules...
:: Loading module phy-rtk-rle059[   12.460966] rtk-usb-phy-rle0599 98013824.usb_phy_rle0599: Probe RTK USB 2.0 RLE0599 PHY
9 ... [  OK  ]
:: Loading module phy-rtk-usb2[   12.480158] rtk-usb2phy 98028280.dwc3_drd_usb2phy: drivers/usb/phy/phy-rtk-usb2.c Probe RTK USB 2.0 PHY
[   12.490208] rtk-usb2phy 98031280.dwc3_u2host_usb2phy: drivers/usb/phy/phy-rtk-usb2.c Probe RTK USB 2.0 PHY
[   12.500302] rtk-usb2phy 981f8280.dwc3_u3host_usb2phy: drivers/usb/phy/phy-rtk-usb2.c Probe RTK USB 2.0 PHY
 ... [  OK  ]
:: Loading module phy-rtk-usb3[   12.520225] rtk-usb3phy 98013210.dwc3_drd_usb3phy: drivers/usb/phy/phy-rtk-usb3.c Probe RTK USB 3.0 PHY
[   12.530162] rtk-usb3phy 98013e10.dwc3_u3host_usb3phy: drivers/usb/phy/phy-rtk-usb3.c Probe RTK USB 3.0 PHY
 ... [  OK  ]
:: Loading module usb-common ... [  OK  ]
:: Loading module usbcore[   12.578107] usbcore: registered new interface driver usbfs
[   12.585384] usbcore: registered new interface driver hub
[   12.591765] usbcore: registered new device driver usb
 ... [  OK  ]
:: Loading module dwc3 ... [  OK  ]
:: Loading module ehci-hcd[   12.639091] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
 ... [  OK  ]
:: Loading module ehci-pci[   12.655840] ehci-pci: EHCI PCI platform driver
 ... [  OK  ]
:: Loading module xhci-hcd ... [  OK  ]
:: Loading module xhci-plat-hcd ... [  OK  ]
:: Loading module xhci-pci ... [  OK  ]
:: Loading module dwc3-rtk[   12.728447] rtk-dwc3 98013200.rtk_dwc3_drd: Probe Realtek-SoC USB DWC3 Host Controller
[   12.738290] dwc3 98020000.dwc3_drd: rtk dwc3 fixed dwc3 globals register start address 0xffffff80026f8100
[   12.749704] rtk-usb3phy 98013210.dwc3_drd_usb3phy: drivers/usb/phy/phy-rtk-usb3.c Init RTK USB 3.0 PHY
[   12.764422] rtk-usb3phy 98013210.dwc3_drd_usb3phy: drivers/usb/phy/phy-rtk-usb3.c Initialized RTK USB 3.0 PHY
[   12.974598] rtk-usb2phy 98028280.dwc3_drd_usb2phy: drivers/usb/phy/phy-rtk-usb2.c Init RTK USB 2.0 PHY
[   12.984158] rtk-usb2phy 98028280.dwc3_drd_usb2phy: drivers/usb/phy/phy-rtk-usb2.c Initialized RTK USB 2.0 PHY
[   13.294551] xhci-hcd xhci-hcd.2.auto: power control enabled
[   13.300263] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[   13.305993] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 2
[   13.314150] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x00010010
[   13.323089] xhci-hcd xhci-hcd.2.auto: irq 9, io mem 0x98020000
[   13.329534] hub 2-0:1.0: USB hub found
[   13.333485] hub 2-0:1.0: 1 port detected
[   13.338741]  port1 is going to power up Vbus by GPIO#23(ACTIVE_HIGH)
[   13.445293] host xhci-hcd.2.auto port 1 has Vbus GPIO#23 with polarity ACTIVE_HIGH
[   13.453268] xhci-hcd xhci-hcd.2.auto: power control enabled
[   13.458979] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[   13.464835] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3
[   13.472732] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[   13.481436] hub 3-0:1.0: USB hub found
[   13.485395] hub 3-0:1.0: 1 port detected
[   13.490635] host xhci-hcd.2.auto port 1 has Vbus GPIO#23 with polarity ACTIVE_HIGH
[   13.500116] rtk-usb-power-manager 98000000.rtk_usb_power_manager: rtk_usb_init_power_on for 98013200.rtk_dwc3_drd
[   13.510685] rtk-dwc3 98013200.rtk_dwc3_drd: dwc3_rtk_probe ok! (take 780 ms)
[   13.518183] rtk-dwc3 98013e00.rtk_dwc3_u3host: Probe Realtek-SoC USB DWC3 Host Controller
[   13.527005] dwc3 981f0000.dwc3_u3host: rtk dwc3 fixed dwc3 globals register start address 0xffffff8002718100
[   13.537452] rtk-usb3phy 98013e10.dwc3_u3host_usb3phy: drivers/usb/phy/phy-rtk-usb3.c Init RTK USB 3.0 PHY
[   13.552426] rtk-usb3phy 98013e10.dwc3_u3host_usb3phy: drivers/usb/phy/phy-rtk-usb3.c Initialized RTK USB 3.0 PHY
[   13.762871] rtk-usb2phy 981f8280.dwc3_u3host_usb2phy: drivers/usb/phy/phy-rtk-usb2.c Init RTK USB 2.0 PHY
[   13.772693] rtk-usb2phy 981f8280.dwc3_u3host_usb2phy: drivers/usb/phy/phy-rtk-usb2.c Initialized RTK USB 2.0 PHY
[   14.083352] xhci-hcd xhci-hcd.5.auto: power control enabled
[   14.089064] xhci-hcd xhci-hcd.5.auto: xHCI Host Controller
[   14.094883] xhci-hcd xhci-hcd.5.auto: new USB bus registered, assigned bus number 4
[   14.103116] xhci-hcd xhci-hcd.5.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x00010010
[   14.112035] xhci-hcd xhci-hcd.5.auto: irq 9, io mem 0x981f0000
[   14.118442] hub 4-0:1.0: USB hub found
[   14.122316] hub 4-0:1.0: 1 port detected
[   14.127932]  port1 is going to power up Vbus by GPIO#22(ACTIVE_HIGH)
[   14.234475] host xhci-hcd.5.auto port 1 has Vbus GPIO#22 with polarity ACTIVE_HIGH
[   14.242447] xhci-hcd xhci-hcd.5.auto: power control enabled
[   14.248189] xhci-hcd xhci-hcd.5.auto: xHCI Host Controller
[   14.253817] xhci-hcd xhci-hcd.5.auto: new USB bus registered, assigned bus number 5
[   14.261695] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM.
[   14.270386] hub 5-0:1.0: USB hub found
[   14.274266] hub 5-0:1.0: 1 port detected
[   14.279613] host xhci-hcd.5.auto port 1 has Vbus GPIO#22 with polarity ACTIVE_HIGH
[   14.287821] rtk-usb-power-manager 98000000.rtk_usb_power_manager: rtk_usb_init_power_on for 98013e00.rtk_dwc3_u3host
[   14.298638] rtk-dwc3 98013e00.rtk_dwc3_u3host: dwc3_rtk_probe ok! (take 780 ms)
 ... [  OK  ]
insmod: can't insert '/lib/modules/etxhci-hcd.ko': No such file [   14.330443] ds418j_synobios: module license 'Synology Inc.' taints kernel.
or directory
Insert net driver([   14.338394] Disabling lock debugging due to kernel taint
Mindspeed only)...
[   14.347401] Synobios DS418j GPIO initialized
[   14.352775] synobios: load, major number 201
[   14.357155] Brand: Synology
[   14.360038] Model: DS-418j
[   14.362923] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[   14.371599] synobios cpu_arch proc entry initialized
[   14.376698] synobios crypto_hw proc entry initialized
[   14.381870] synobios syno_platform proc entry initialized
[   14.387558] synobios open /dev/ttyS1 success
Starting /usr/syno/bin/synocfgen...
/usr/syno/bin/synocfgen returns 0
[   14.402182] synobios: unload
Exit on error [1] DISK NOT INSTALLED...
Tue Sep 30 11:31:13 UTC 2025
none /sys/kernel/debug debugfs rw,relatime 0 0
sys /sys sysfs rw,relatime 0 0
none /dev devtmpfs rw,relatime,size=486960k,nr_inodes=121740,mode=755 0 0
proc /proc proc rw,relatime 0 0
linuxrc.syno failed on 1
starting pid 1728, tty '': '/etc/rc'
:: Starting /etc/rc
:: Mounting procfs ... [  OK  ]
:: Mounting tmpfs ... [  OK  ]
:: Mounting devtmpfs ... [  OK  ]
:: Mounting devpts ... [  OK  ]
:: Mounting sysfs ... [  OK  ]
mdadm: error opening /dev/md1: No such file or directory
rc: Use all internal disk as swap.
rc: No internal disk installed.
swapon: can't stat '/dev/md1': No such file or directory
:: Loading module fat ... [  OK  ]
:: Loading module vfat ... [  OK  ]
:: Loading module r8168 ... [  OK  ]
[   15.058285] Synobios DS418j GPIO initialized
[   15.062747] synobios: load, major number 201
[   15.067128] Brand: Synology
[   15.070010] Model: DS-418j
[   15.072835] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[   15.081525] synobios cpu_arch proc entry initialized
[   15.086780] synobios crypto_hw proc entry initialized
[   15.091953] synobios syno_platform proc entry initialized
[   15.097651] synobios open /dev/ttyS1 success
mknod: /dev/synobios: File exists
Starting SW init...
/etc/rc:[   15.108739] synobios: unload
 line 215: /usr/syno/bin/syno_led_mask_on: not found
:: Loading module synobios[   15.831664] Synobios DS418j GPIO initialized
[   15.836524] synobios: load, major number 201
[   15.840908] Brand: Synology
[   15.843805] Model: DS-418j
[   15.846590] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[   15.855316] synobios cpu_arch proc entry initialized
[   15.860400] synobios crypto_hw proc entry initialized
[   15.865575] synobios syno_platform proc entry initialized
[   15.871247] synobios open /dev/ttyS1 success
 ... [  OK  ]
[   16.065131] r8169 98016000.gmac eth0: rtl_csiar_cond == 0 (loop: 100, delay: 10).
[   16.074061] r8169 98016000.gmac eth0: rtl_csiar_cond == 1 (loop: 100, delay: 10).
[   16.082978] r8169 98016000.gmac eth0: link down
udhcpc (v1.16.1) started
eth0      Link encap:Ethernet  HWaddr 00:11:32:97:53:D9
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:11

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

:: Starting syslogd ... [  OK  ]
/etc/rc: line 305: /usr/syno/bin/syno_pstore_collect: not found
:: Starting scemd
[   20.072712] pctrl-rtk: rtk_powerctrl_manager: begin
[   20.077960] pctrl-rtk: pctrl_l4_icg_scpu_wrapper::ENABLE_HW_PM, ret = 0
[   20.099762] pctrl-rtk: pctrl_l4_icg_tp::ENABLE_HW_PM, ret = -1
[   20.115755] pctrl-rtk: pctrl_l4_icg_rsa::ENABLE_HW_PM, ret = 0
[   20.131741] pctrl-rtk: pctrl_l4_icg_cp::ENABLE_HW_PM, ret = 0
[   20.147645] pctrl-rtk: pctrl_l4_icg_gspi::ENABLE_HW_PM, ret = -1
[   20.158872] pctrl-rtk: pctrl_nat::POWER_OFF, ret = 0
[   20.168974] pctrl-rtk: pctrl_l4_icg_nat_wrap::ENABLE_HW_PM, ret = -1
[   20.190543] pctrl-rtk: rtk_powerctrl_manager: done
:: Starting services in background
Starting findhostd in flash_rd...
Starting services in flash_rd...
Running /usr/syno/etc/rc.d/J01httpd.sh...
Starting httpd:80 in flash_rd...
Starting httpd:5000 in flash_rd...
Running /usr/syno/etc/rc.d/J03ssdpd.sh...
/usr/bin/minissdpd -i eth0
eth0 not RUNNING
Running /usr/syno/etc/rc.d/J04synoagentregisterd.sh...
Starting synoagentregisterd...
Running /usr/syno/etc/rc.d/J30DisableNCQ.sh...
cat: can't open '/sys/block/sd*/device//model': No such file or directory
Running /usr/syno/etc/rc.d/J80ADTFanControl.sh...
Running /usr/syno/etc/rc.d/J98nbnsd.sh...
Starting nbnsd...
Running /usr/syno/etc/rc.d/J99avahi.sh...
Starting Avahi mDNS/DNS-SD Daemo[   24.060856] random: avahi-daemon: uninitialized urandom read (4 bytes read, 13 bits of entropy available)
n
cname_load_conf failed:/var/tmp/[   24.074843] random: avahi-daemon: uninitialized urandom read (8 bytes read, 13 bits of entropy available)
nginx/avahi-aliases.conf
:: Loading module usb-storage[   24.160123] usbcore: registered new interface driver usb-storage
 ... [  OK  ]
:: Loading module syno_hddmon[   25.004877] Syno_HddMon: Initialization completed.
 ... [  OK  ]
============ Date ============
Tue Sep 30 11:31:24 UTC 2025

Tue Sep 30 11:31:25 2025

DiskStation login: ▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒oot
Password:
Login timed out after 60 seco
Tue Sep 30 11:36:18 2025

DiskStation login: root
Password:
Login incorrect
DiskStation login: root
Password:
Login incorrect
DiskStation login: [  523.740516] r8169 98016000.gmac eth0: link up 100 Mbps
[  523.745795] r8169_reset_task: reset with slow event.
[  523.786676] r8169 98016000.gmac eth0: rtl_csiar_cond == 0 (loop: 100, delay: 10).
[  523.795597] r8169 98016000.gmac eth0: rtl_csiar_cond == 1 (loop: 100, delay: 10).
[  523.804513] r8169 98016000.gmac eth0: link down
[  523.809165] r8169 98016000.gmac eth0: link down
[  537.455833] r8169 98016000.gmac eth0: link up 100 Mbps
[  537.461106] r8169_reset_task: reset with slow event.
[  537.496623] r8169 98016000.gmac eth0: rtl_csiar_cond == 0 (loop: 100, delay: 10).
[  537.505549] r8169 98016000.gmac eth0: rtl_csiar_cond == 1 (loop: 100, delay: 10).
[  537.514469] r8169 98016000.gmac eth0: link up 100 Mbps
[  537.519745] r8169 98016000.gmac eth0: link down
[  550.980308] r8169 98016000.gmac eth0: link up 100 Mbps
[  550.985587] r8169_reset_task: reset with slow event.

Login timed out after 60 seconds[  551.026641] r8169 98016000.gmac eth0: rtl_csiar_cond == 0 (loop: 100, delay: 10).
[  551.035567] r8169 98016000.gmac eth0: rtl_csiar_cond == 1 (loop: 100, delay: 10).
[  551.044496] r8169 98016000.gmac eth0: link down
[  551.049150] r8169 98016000.gmac eth0: link down

Tue Sep 30 11:40:11 2025

DiskStation login: [  564.523658] r8169 98016000.gmac eth0: link up 100 Mbps
[  564.528930] r8169_reset_task: reset with slow event.
[  564.566634] r8169 98016000.gmac eth0: rtl_csiar_cond == 0 (loop: 100, delay: 10).
[  564.575554] r8169 98016000.gmac eth0: rtl_csiar_cond == 1 (loop: 100, delay: 10).
[  564.584478] r8169 98016000.gmac eth0: link down
[  564.589129] r8169 98016000.gmac eth0: link down
[  578.138308] r8169 98016000.gmac eth0: link up 100 Mbps
[  578.143588] r8169_reset_task: reset with slow event.
[  578.176640] r8169 98016000.gmac eth0: rtl_csiar_cond == 0 (loop: 100, delay: 10).
[  578.185557] r8169 98016000.gmac eth0: rtl_csiar_cond == 1 (loop: 100, delay: 10).
[  578.194479] r8169 98016000.gmac eth0: link up 100 Mbps
[  578.199756] r8169 98016000.gmac eth0: link down
[  591.786515] r8169 98016000.gmac eth0: link up 100 Mbps
[  591.791786] r8169_reset_task: reset with slow event.
[  591.826635] r8169 98016000.gmac eth0: rtl_csiar_cond == 0 (loop: 100, delay: 10).
[  591.835552] r8169 98016000.gmac eth0: rtl_csiar_cond == 1 (loop: 100, delay: 10).
[  591.844476] r8169 98016000.gmac eth0: link up 100 Mbps
[  591.849751] r8169 98016000.gmac eth0: link down
[  605.269047] r8169 98016000.gmac eth0: link up 100 Mbps
[  605.274328] r8169_reset_task: reset with slow event.
[  605.306641] r8169 98016000.gmac eth0: rtl_csiar_cond == 0 (loop: 100, delay: 10).
[  605.315559] r8169 98016000.gmac eth0: rtl_csiar_cond == 1 (loop: 100, delay: 10).
[  605.324485] r8169 98016000.gmac eth0: link up 100 Mbps
[  605.329762] r8169 98016000.gmac eth0: link down
[  618.927739] r8169 98016000.gmac eth0: link up 100 Mbps
[  618.933020] r8169_reset_task: reset with slow event.
[  618.966634] r8169 98016000.gmac eth0: rtl_csiar_cond == 0 (loop: 100, delay: 10).
[  618.975552] r8169 98016000.gmac eth0: rtl_csiar_cond == 1 (loop: 100, delay: 10).
[  618.984466] r8169 98016000.gmac eth0: link up 100 Mbps
[  618.989744] r8169 98016000.gmac eth0: link down
[  632.406077] r8169 98016000.gmac eth0: link up 100 Mbps
[  632.411349] r8169_reset_task: reset with slow event.
[  632.446647] r8169 98016000.gmac eth0: rtl_csiar_cond == 0 (loop: 100, delay: 10).
[  632.455567] r8169 98016000.gmac eth0: rtl_csiar_cond == 1 (loop: 100, delay: 10).
[  632.464490] r8169 98016000.gmac eth0: link up 100 Mbps
[  632.469767] r8169 98016000.gmac eth0: link down

The last lines in the log appear when I connect a RJ45 cable.
The LED on the switch are off, but there is a quick flash after 10s.
The slot RJ45 is not damaged...
Could you help me ?

====
bodhi's edit: please use code tags (Formatted code button) to post log.



Edited 2 time(s). Last edit at 09/30/2025 03:43PM by bodhi.

bneben,

I don't have this NAS. So the following is my observation and educated guess.

This problem is probably related to the fact that this box use the Realtek 8169 NIC. And its MTU is set to jumbo frame.

In order for jumbo frame to work,

1. All nodes in the entire 1GBs LAN must run at 1Gbps. So each box connected to the network must has 1Gbps NIC.
2. The MTU must be set to the same number.

If either of the above is not satisified, the negotiation will fail.

Here in the log:

> [   11.639380] r8169 Gigabit Ethernet driver
> 2.32.5-LK-NAPI loaded
> [   11.673722] r8169 98016000.gmac eth0:
> RTL8169SOC at 0xffffff80005a6000,
> 00:10:20:30:40:50, XID 10900800 IRQ 11
> [   11.684018] r8169 98016000.gmac eth0: jumbo
> features [frames: 9200 bytes, tx checksumming:
> ko]

So it is 9200, and the box probably cannot negotiate this frame size within your LAN.

> DiskStation login: [  564.523658] r8169
> 98016000.gmac eth0: link up 100 Mbps
> [  564.528930] r8169_reset_task: reset with slow
> event.

<snip>

> 100 Mbps
> [  632.411349] r8169_reset_task: reset with slow
> event.
> [  632.446647] r8169 98016000.gmac eth0:
> rtl_csiar_cond == 0 (loop: 100, delay: 10).
> [  632.455567] r8169 98016000.gmac eth0:
> rtl_csiar_cond == 1 (loop: 100, delay: 10).
> [  632.464490] r8169 98016000.gmac eth0: link up
> 100 Mbps
> [  632.469767] r8169 98016000.gmac eth0: link
> down

So the speed is down to 100 Mbps, and the link keep going up/down because Auto Negotiation is active.

====

If you can log into the Diskstation DSM, you can try to use ethtool to set the MTU and Auto Negotiation to a typical settings for a Gbits network and see if the link will be stable.

For example, turn off auto negotiation after the NIC is running, at the Linux shell command line:

ethtool -s eth0 autoneg off

After you've done this, the NIC will stay up at 100Mbs. And you can connect with SSH.

And then set the MTU to 1500 (try if you can, figure out the ethtool command, I've forgot the exact syntax).

ethtool --help

And turn Auto Negotiation back on. After you see the speed is 1Gbps, turn it off again.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Wow thank you ! it seems that this is a good way to solve the issue ! I will try this evening

I'm back soon for an update !

Hi

Issue not solved yesterday...
I tried to connect the NAS directly to my computer, it is more easier than modify my switch.

So, after the cable plugged, I tried :
- to force the link to 1000 fullduplex on my PC => same issue
- to force the link to 100 fullduplex on my PC => connexion is established but to 10mbits !

In the second case above, the LAN LED in the NAS is green, and the log show a "link up to 10mbits". But no IP discovered by a scan on my computer, and no server detected by Synology assistant.

I'm blocked...
I verified lot of things on the mainboard (RJ45 slot, tracks, capacitor, resistors, pairs ...), all seems "ok" (for me)

I exposed the issue to Chatgpt, and he proposal me to install manually the DSM system on th hard disk, and try to boot on it. This way will give me the possibility to send commands to the NAS (because it is not possible righ now with Putty and the UART, I can only try to log me but no root/admin account works).

I attached the procedure shared by chatgpt... I will try this ! PS : sorry it is in French



Edited 2 time(s). Last edit at 10/02/2025 06:51AM by bneben.

Did you try adjusting the MTU like bohdi suggested?

I tried with a MTU @ 4088, 9014, 16128 (I can't set other value)
The only way to make a link is to set the speed @10Mbits (not 100 as noted above)

My controler is a RTL8125.

@bneben,


> I exposed the issue to Chatgpt, and he proposal me
> to install manually the DSM system on th hard
> disk, and try to boot on it.

It's the correct solution if you don't care about what's in the HDD.

Attach the ethernet cable to a switch like before. Power up and interrupt serial console at countdown

U-Boot 2015.07-g428cfe7-dirty (May 16 2018 - 10:33:51 +0800)

CPU  : Cortex-A53 Quad Core
Board: Realtek QA Board
DRAM:  1 GiB
mapping memory 0x20000000-0x40000000 non-cached
In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  0

List the current envs (to see what was the ipaddr before you set it like below).

printenv

And set your ipaddr to a sane value in your LAN, and try to bring up the network. For example, if your router is 192.168.0.1

setenv ipaddr 192.168.0.100
ping 192.168.0.1

If the ping was successful, then the network is up. Try setting up internet

setenv gatewayip 192.168.0.1
setenv netmask 255.255.255.0
ping 8.8.8.8

If you successfully ping the router and google.com then you have network in u-boot. Try booting into DSM

boot

See if the behavior change.


======

After doing the above, and if the link is still up/down. And if you had network in u-boot. You can reinstall DSM at u-boot prompt using a different HDD.

Reboot the box and set up envs for network like above. And boot. It will allow you to install DSM because there is nothing on the HDD.

After you've installed DSM, you can create new admin account (using the web page) to log in. Use admin as user name for this administrative account.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Unfortunatly, I can't stop the boot, I already tested.
-> Hit any key to stop autoboot: 0

I hit a key, but the boot don't stop...

Yes my hard disk is empty and can be used for test

> Unfortunatly, I can't stop the boot, I already
> tested.
> -> Hit any key to stop autoboot: 0
>
> I hit a key, but the boot don't stop...

Try Control-C.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

OK I will try.
Concerning the MTU value, it seems that the line that indicate 9200o is a default value, like the MAC address just above (00:10:20:30:40:50)
The MAC and MTU are set further down in the log :

eth0      Link encap:Ethernet  HWaddr 00:11:32:97:53:D9
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:11

bneben,

> eth0 Link encap:Ethernet HWaddr
> 00:11:32:97:53:D9
> UP BROADCAST MULTICAST MTU:1500

Yes, DSM must have failed and set to 1500.

The bottom line is you need to boot into DMS and fix the problem inside. The main problem seems to be Auto Negotiation. The NIC kept trying for 1Gbps and got 100Mbps so you dont have network up long enough to log in. If you test the network in u-boot successfully, like I suggested, you can install DSM and set your admin password, and then log in with either serial or SSH to work around this problem.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Unfortunately, nothing worked (the manually created disk), nor did being able to stop the NAS from booting (I think the timeout is set to 0).

However, I successfully enter in root account by remove the backup battery and enter the 101-0101 password, which gives me access to BusyBox v1.16.1 (but many commands don't work with this box...).

> Unfortunately, nothing worked (the manually
> created disk), nor did being able to stop the NAS
> from booting (I think the timeout is set to 0).
>

How about start pounding Control-C as soon as the box is power on, don't wait for the countdown.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Nothing can stop the boot :/
I tried different keys / ctrl+C (and others) / lot of time during the boot (and directly after the power up sequence)...

It seems that the inputs are not validate before the line "START /linuxrc.syno" (the inputs caracteres are showed after this line).

I can acces to the busybox with a root access, no more :/
I tried lot of things with the network (Speed connection, MTU, ...)

Quote
boot log

Hit Esc or Tab key to enter console mode or rescue linux: 0

So try typing Esc or Tab key as soon as you see the first character appear on the console.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)



Edited 1 time(s). Last edit at 10/07/2025 08:46PM by bodhi.

No keys are view as an input in the "boot sequence"... Until the line "START /linuxrc.syno".
I tried all keys.

But I have made a big jump this week ! With Busybox, I was authorized to enter some commands, so I put an ip-fix, connected the NAS directly to my computer and set my PC to the same network (without gateway, important !)
I locked the speed to 10mbits, and I'm connected to the nas successfully.

After that, I installed DSM on my drive, and configure it.
All seems OK in DSM.
But the connexion is lost if I set a speed to 100 or 1000mbits :/ Again same issue as above.

For me it seems a hardware issue... Maybe the RJ45 slot, or the input filters (resistors and capacitor) on the cable side on the MB. There are magnetics transformers also on the MB, but I don't think that this is the cause...

It is designed as showed on the picture attached. Strange things, I measured the values for the 4 resistors, and only one is 50ohms. One other is 75, other is 127 and last is 127 too... Without cables, all values should be 49.9ohms (or 50 with my multimeter ;) )

bneben Wrote:

> All seems OK in DSM.
> But the connexion is lost if I set a speed to 100
> or 1000mbits :/ Again same issue as above.

Did you try my recommendation above?

https://forum.doozan.com/read.php?3,140270,140273#msg-140273

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Yes, autoneg is off.

Update :

Following the RJ45 design, and as explained in this link :
https://www.we-online.com/components/media/o721295v410%20RD016%20EN-GB-Ethernet%20Front%20End.pdf

I have a physical issue, I don't know where right now, but I have made progress on the subject.

I used my DLink switch for launch a diag on the port where the NAS is plugged, and the result is that the pair "4" is shorted. All other pairs are "OK".
With my multimeter, I checked :
- the impedance of each pair => 1.4ohm each
- the impedence between each pair => 180 ohms between pair 4 and 1, 203ohm between pair 4 and 2 or 3, 150ohms between 2 and 3, 203ohm between 4 and 3, 124ohms between 3 and 1 (values measured on the RJ45 port)
- the value of each resistor on the Bob smith filter => RPair 1 : 128, RPair 2 : 73, RPair 3 : 73, RPair 4 : 50
- capacitor is 1.2nf

In reSume, values of each R of the filter should be equal, it is not the case.
There is no physical damages
Capacitor of the filter return a true value

New step, I will desolder the resistors / capacitors of the filter, and check again... The magnetics tranformers protect the board, so if an over voltage was applied, the filter should be dead :/



Edited 1 time(s). Last edit at 10/14/2025 01:52AM by bneben.