PogoPlug E02 Black
Posted by msanad
|
PogoPlug E02 Black February 23, 2014 02:47AM |
Registered: 10 years ago Posts: 37 |
hello every one
i have bought my PogoPlug E02 black one one week ago and yesterday i tried to install uboot (/install_uboot_mtd0.sh) and then to install Arch Linux ARM but unfortunallty i go error message (Installation cancelled.) then i forced the installation with (--no-uboot-check ) but again i go this message (uBoot could not be downloaded, or the MD5 does not match.)
the prompet of the switched from bash to pogoplug and i have tried to install again but with no result.
then i found one topic (dont remeber it now ) which contains some steps how to remove some data from flash and the earse !!!! actully i'm not fimilar with these command in unix but i tried it.
now i cant access it via ssh but can access using serial connection , below is the messages i got , it stops at this line
then start the boot over again
now i need to know how to fix this issue to run ARM on this box or to return to the default pogoplug image.
Waiting for your help
thanks
i have bought my PogoPlug E02 black one one week ago and yesterday i tried to install uboot (/install_uboot_mtd0.sh) and then to install Arch Linux ARM but unfortunallty i go error message (Installation cancelled.) then i forced the installation with (--no-uboot-check ) but again i go this message (uBoot could not be downloaded, or the MD5 does not match.)
the prompet of the switched from bash to pogoplug and i have tried to install again but with no result.
then i found one topic (dont remeber it now ) which contains some steps how to remove some data from flash and the earse !!!! actully i'm not fimilar with these command in unix but i tried it.
now i cant access it via ssh but can access using serial connection , below is the messages i got , it stops at this line
Scheduling watchdog timeout to force reboot...
then start the boot over again
U-Boot 1.1.4 (Sep 28 2009 - 11:55:23) Cloud Engines v2.0 (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: PPV2 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x100000, size 0x200000 Reading data from 0x2ff800 -- 100% complete. 2097152 bytes read: OK ## Booting image at 00800000 ... Image Name: Linux-2.6.22.18 Created: 2010-10-19 23:05:02 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1979140 Bytes = 1.9 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux............................................................................................................................ done, booting the kernel. [ 0.000000] Linux version 2.6.22.18 (bdietrich@buildman) (gcc version 4.2.1) #81 Tue Oct 19 16:05:00 PDT 2010 [ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177 [ 0.000000] Machine: Feroceon-KW [ 0.000000] Using UBoot passing parameters structure [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] CPU0: D VIVT write-back cache [ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] Built 1 zonelists. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro [ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes) [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.010000] Memory: 256MB 0MB 0MB 0MB = 256MB total [ 0.010000] Memory: 255872KB available (3592K code, 253K data, 124K init) [ 0.250000] Mount-cache hash table entries: 512 [ 0.250000] CPU: Testing write buffer coherency: ok [ 0.250000] NET: Registered protocol family 16 [ 0.250000] [ 0.250000] CPU Interface [ 0.250000] ------------- [ 0.250000] SDRAM_CS0 ....base 00000000, size 256MB [ 0.250000] SDRAM_CS1 ....disable [ 0.250000] SDRAM_CS2 ....disable [ 0.250000] SDRAM_CS3 ....disable [ 0.250000] PEX0_MEM ....base e8000000, size 128MB [ 0.250000] PEX0_IO ....base f2000000, size 1MB [ 0.250000] INTER_REGS ....base f1000000, size 1MB [ 0.250000] NFLASH_CS ....base fa000000, size 2MB [ 0.250000] SPI_CS ....base f4000000, size 16MB [ 0.250000] BOOT_ROM_CS ....no such [ 0.250000] DEV_BOOTCS ....no such [ 0.250000] CRYPT_ENG ....base f0000000, size 2MB [ 0.250000] [ 0.250000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21_with_rx_desc_tuned)-- SHEEVA PLUG Soc: 88F6281 A0 LE [ 0.250000] [ 0.250000] Detected Tclk 200000000 and SysClk 400000000 [ 0.250000] MV Buttons Device Load [ 0.250000] Marvell USB EHCI Host controller #0: c0652600 [ 0.750000] PEX0 interface detected no Link. [ 0.750000] PCI: bus0: Fast back to back transfers enabled [ 0.750000] SCSI subsystem initialized [ 0.750000] usbcore: registered new interface driver usbfs [ 0.750000] usbcore: registered new interface driver hub [ 0.750000] usbcore: registered new device driver usb [ 0.750000] NET: Registered protocol family 2 [ 0.760000] Time: kw_clocksource clocksource has been installed. [ 0.850000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.850000] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.850000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes) [ 0.850000] TCP: Hash tables configured (established 8192 bind 8192) [ 0.850000] TCP reno registered [ 0.880000] RTC has been updated!!! [ 0.880000] RTC registered [ 0.880000] Use the XOR engines (acceleration) for enhancing the following functions: [ 0.880000] o RAID 5 Xor calculation [ 0.880000] o kernel memcpy [ 0.880000] o kenrel memzero [ 0.880000] Number of XOR engines to use: 4 [ 0.880000] cesadev_init(c00117b0) [ 0.880000] mvCesaInit: sessions=640, queue=64, pSram=f0000000 [ 0.880000] MV Buttons Driver Load [ 0.880000] squashfs: version 3.3 (2007/10/31) Phillip Lougher [ 0.880000] squashfs: LZMA suppport for slax.org by jro [ 0.880000] JFFS2 version 2.2. (NAND) أ‚آ© 2001-2006 Red Hat, Inc. [ 0.880000] io scheduler noop registered [ 0.880000] io scheduler anticipatory registered (default) [ 0.900000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [ 0.900000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A [ 0.910000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize [ 0.920000] Loading Marvell Ethernet Driver: [ 0.920000] o Cached descriptors in DRAM [ 0.920000] o DRAM SW cache-coherency [ 0.930000] o Single RX Queue support - ETH_DEF_RXQ=0 [ 0.930000] o Single TX Queue support - ETH_DEF_TXQ=0 [ 0.940000] o TCP segmentation offload enabled [ 0.940000] o Receive checksum offload enabled [ 0.950000] o Transmit checksum offload enabled [ 0.950000] o Network Fast Processing (Routing) supported [ 0.960000] o Driver ERROR statistics enabled [ 0.960000] o Driver INFO statistics enabled [ 0.970000] o Proc tool API enabled [ 0.970000] o Rx descripors: q0=128 [ 0.970000] o Tx descripors: q0=532 [ 0.980000] o Loading network interface(s): [ 0.990000] o eth0, ifindex = 1, GbE port = 0 [ 0.990000] o eth1, ifindex = 2, GbE port = 1 [ 1.000000] [ 1.000000] mvFpRuleDb (cfdf6000): 2048 entries, 8192 bytes [ 1.000000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI [ 1.010000] Copyright (c) 1999-2006 Intel Corporation. [ 1.020000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI [ 1.020000] e100: Copyright(c) 1999-2006 Intel Corporation [ 1.030000] [ 1.030000] Warning Sata is Powered Off [ 1.030000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ [ 1.040000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit) [ 1.050000] Scanning device for bad blocks [ 1.100000] Using static partition definition [ 1.110000] Creating 4 MTD partitions on "nand_mtd": [ 1.110000] 0x00000000-0x00100000 : "u-boot" [ 1.120000] 0x00100000-0x00500000 : "uImage" [ 1.120000] 0x00500000-0x02500000 : "root" [ 1.130000] 0x02500000-0x08000000 : "data" [ 1.130000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI [ 1.140000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 [ 1.180000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 [ 1.200000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 1.200000] usb usb1: configuration #1 chosen from 1 choice [ 1.210000] hub 1-0:1.0: USB hub found [ 1.210000] hub 1-0:1.0: 1 port detected [ 1.330000] USB Universal Host Controller Interface driver v3.0 [ 1.610000] usb 1-1: new high speed USB device using ehci_marvell and address 2 [ 1.760000] usb 1-1: configuration #1 chosen from 1 choice [ 1.760000] hub 1-1:1.0: USB hub found [ 1.770000] hub 1-1:1.0: 4 ports detected [ 1.880000] usbcore: registered new interface driver usblp [ 1.880000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver [ 1.890000] Initializing USB Mass Storage driver... [ 1.890000] usbcore: registered new interface driver usb-storage [ 1.900000] USB Mass Storage support registered. [ 1.910000] mice: PS/2 mouse device common for all mice [ 1.910000] i2c /dev entries driver [ 1.910000] Linux telephony interface: v1.00 [ 1.920000] md: linear personality registered for level -1 [ 1.920000] md: raid0 personality registered for level 0 [ 1.930000] md: raid1 personality registered for level 1 [ 2.100000] raid6: int32x1 97 MB/s [ 2.270000] raid6: int32x2 114 MB/s [ 2.440000] raid6: int32x4 122 MB/s [ 2.610000] raid6: int32x8 110 MB/s [ 2.610000] raid6: using algorithm int32x4 (122 MB/s) [ 2.610000] md: raid6 personality registered for level 6 [ 2.620000] md: raid5 personality registered for level 5 [ 2.620000] md: raid4 personality registered for level 4 [ 2.630000] raid5: measuring checksumming speed [ 2.680000] arm4regs : 1084.000 MB/sec [ 2.730000] 8regs : 754.800 MB/sec [ 2.780000] 32regs : 900.000 MB/sec [ 2.780000] raid5: using function: arm4regs (1084.000 MB/sec) [ 2.790000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com [ 2.790000] dm_crypt using the OCF package. [ 2.800000] sdhci: Secure Digital Host Controller Interface driver [ 2.800000] sdhci: Copyright(c) Pierre Ossman [ 2.810000] usbcore: registered new interface driver usbhid [ 2.810000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 2.820000] TCP cubic registered [ 2.820000] NET: Registered protocol family 1 [ 2.830000] NET: Registered protocol family 17 [ 2.830000] md: Autodetecting RAID arrays. [ 2.840000] md: autorun ... [ 2.840000] md: ... autorun DONE. [ 3.070000] VFS: Mounted root (jffs2 filesystem) readonly. [ 3.070000] Freeing init memory: 124K [ 3.070000] Warning: unable to open an initial console. [ 3.080000] Kernel panic - not syncing: No init found. Try passing init= option to kernel. [ 3.090000] Scheduling watchdog timeout to force reboot... U-Boot 1.1.4 (Sep 28 2009 - 11:55:23) Cloud Engines v2.0 (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: PPV2 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x100000, size 0x200000 Reading data from 0x2ff800 -- 100% complete. 2097152 bytes read: OK ## Booting image at 00800000 ... Image Name: Linux-2.6.22.18 Created: 2010-10-19 23:05:02 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1979140 Bytes = 1.9 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux............................................................................................................................ done, booting the kernel. [ 0.000000] Linux version 2.6.22.18 (bdietrich@buildman) (gcc version 4.2.1) #81 Tue Oct 19 16:05:00 PDT 2010 [ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177 [ 0.000000] Machine: Feroceon-KW [ 0.000000] Using UBoot passing parameters structure [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] CPU0: D VIVT write-back cache [ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] Built 1 zonelists. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro [ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes) [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.010000] Memory: 256MB 0MB 0MB 0MB = 256MB total [ 0.010000] Memory: 255872KB available (3592K code, 253K data, 124K init) [ 0.250000] Mount-cache hash table entries: 512 [ 0.250000] CPU: Testing write buffer coherency: ok [ 0.250000] NET: Registered protocol family 16 [ 0.250000] [ 0.250000] CPU Interface [ 0.250000] ------------- [ 0.250000] SDRAM_CS0 ....base 00000000, size 256MB [ 0.250000] SDRAM_CS1 ....disable [ 0.250000] SDRAM_CS2 ....disable [ 0.250000] SDRAM_CS3 ....disable [ 0.250000] PEX0_MEM ....base e8000000, size 128MB [ 0.250000] PEX0_IO ....base f2000000, size 1MB [ 0.250000] INTER_REGS ....base f1000000, size 1MB [ 0.250000] NFLASH_CS ....base fa000000, size 2MB [ 0.250000] SPI_CS ....base f4000000, size 16MB [ 0.250000] BOOT_ROM_CS ....no such [ 0.250000] DEV_BOOTCS ....no such [ 0.250000] CRYPT_ENG ....base f0000000, size 2MB [ 0.250000] [ 0.250000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21_with_rx_desc_tuned)-- SHEEVA PLUG Soc: 88F6281 A0 LE [ 0.250000] [ 0.250000] Detected Tclk 200000000 and SysClk 400000000 [ 0.250000] MV Buttons Device Load [ 0.250000] Marvell USB EHCI Host controller #0: c0652600 [ 0.750000] PEX0 interface detected no Link. [ 0.750000] PCI: bus0: Fast back to back transfers enabled [ 0.750000] SCSI subsystem initialized [ 0.750000] usbcore: registered new interface driver usbfs [ 0.750000] usbcore: registered new interface driver hub [ 0.750000] usbcore: registered new device driver usb [ 0.750000] NET: Registered protocol family 2 [ 0.760000] Time: kw_clocksource clocksource has been installed. [ 0.850000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.850000] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.850000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes) [ 0.850000] TCP: Hash tables configured (established 8192 bind 8192) [ 0.850000] TCP reno registered [ 0.880000] RTC has been updated!!! [ 0.880000] RTC registered [ 0.880000] Use the XOR engines (acceleration) for enhancing the following functions: [ 0.880000] o RAID 5 Xor calculation [ 0.880000] o kernel memcpy [ 0.880000] o kenrel memzero [ 0.880000] Number of XOR engines to use: 4 [ 0.880000] cesadev_init(c00117b0) [ 0.880000] mvCesaInit: sessions=640, queue=64, pSram=f0000000 [ 0.880000] MV Buttons Driver Load [ 0.880000] squashfs: version 3.3 (2007/10/31) Phillip Lougher [ 0.880000] squashfs: LZMA suppport for slax.org by jro [ 0.880000] JFFS2 version 2.2. (NAND) أ‚آ© 2001-2006 Red Hat, Inc. [ 0.880000] io scheduler noop registered [ 0.880000] io scheduler anticipatory registered (default) [ 0.900000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [ 0.900000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A [ 0.910000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize [ 0.920000] Loading Marvell Ethernet Driver: [ 0.920000] o Cached descriptors in DRAM [ 0.920000] o DRAM SW cache-coherency [ 0.930000] o Single RX Queue support - ETH_DEF_RXQ=0 [ 0.930000] o Single TX Queue support - ETH_DEF_TXQ=0 [ 0.940000] o TCP segmentation offload enabled [ 0.940000] o Receive checksum offload enabled [ 0.950000] o Transmit checksum offload enabled [ 0.950000] o Network Fast Processing (Routing) supported [ 0.960000] o Driver ERROR statistics enabled [ 0.960000] o Driver INFO statistics enabled [ 0.970000] o Proc tool API enabled [ 0.970000] o Rx descripors: q0=128 [ 0.970000] o Tx descripors: q0=532 [ 0.980000] o Loading network interface(s): [ 0.990000] o eth0, ifindex = 1, GbE port = 0 [ 0.990000] o eth1, ifindex = 2, GbE port = 1 [ 1.000000] [ 1.000000] mvFpRuleDb (cfdf6000): 2048 entries, 8192 bytes [ 1.000000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI [ 1.010000] Copyright (c) 1999-2006 Intel Corporation. [ 1.020000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI [ 1.020000] e100: Copyright(c) 1999-2006 Intel Corporation [ 1.030000] [ 1.030000] Warning Sata is Powered Off [ 1.030000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ [ 1.040000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit) [ 1.050000] Scanning device for bad blocks [ 1.100000] Using static partition definition [ 1.110000] Creating 4 MTD partitions on "nand_mtd": [ 1.110000] 0x00000000-0x00100000 : "u-boot" [ 1.120000] 0x00100000-0x00500000 : "uImage" [ 1.120000] 0x00500000-0x02500000 : "root" [ 1.130000] 0x02500000-0x08000000 : "data" [ 1.130000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI [ 1.140000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 [ 1.180000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 [ 1.200000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 1.200000] usb usb1: configuration #1 chosen from 1 choice [ 1.210000] hub 1-0:1.0: USB hub found [ 1.210000] hub 1-0:1.0: 1 port detected [ 1.330000] USB Universal Host Controller Interface driver v3.0 [ 1.610000] usb 1-1: new high speed USB device using ehci_marvell and address 2 [ 1.760000] usb 1-1: configuration #1 chosen from 1 choice [ 1.760000] hub 1-1:1.0: USB hub found [ 1.770000] hub 1-1:1.0: 4 ports detected [ 1.880000] usbcore: registered new interface driver usblp [ 1.880000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver [ 1.890000] Initializing USB Mass Storage driver... [ 1.890000] usbcore: registered new interface driver usb-storage [ 1.900000] USB Mass Storage support registered. [ 1.910000] mice: PS/2 mouse device common for all mice [ 1.910000] i2c /dev entries driver [ 1.910000] Linux telephony interface: v1.00 [ 1.920000] md: linear personality registered for level -1 [ 1.920000] md: raid0 personality registered for level 0 [ 1.930000] md: raid1 personality registered for level 1 [ 2.100000] raid6: int32x1 97 MB/s [ 2.270000] raid6: int32x2 114 MB/s [ 2.440000] raid6: int32x4 122 MB/s [ 2.610000] raid6: int32x8 110 MB/s [ 2.610000] raid6: using algorithm int32x4 (122 MB/s) [ 2.610000] md: raid6 personality registered for level 6 [ 2.620000] md: raid5 personality registered for level 5 [ 2.620000] md: raid4 personality registered for level 4 [ 2.630000] raid5: measuring checksumming speed [ 2.680000] arm4regs : 1071.600 MB/sec [ 2.730000] 8regs : 754.800 MB/sec [ 2.780000] 32regs : 900.000 MB/sec [ 2.780000] raid5: using function: arm4regs (1071.600 MB/sec) [ 2.790000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com [ 2.790000] dm_crypt using the OCF package. [ 2.800000] sdhci: Secure Digital Host Controller Interface driver [ 2.800000] sdhci: Copyright(c) Pierre Ossman [ 2.810000] usbcore: registered new interface driver usbhid [ 2.810000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 2.820000] TCP cubic registered [ 2.820000] NET: Registered protocol family 1 [ 2.830000] NET: Registered protocol family 17 [ 2.830000] md: Autodetecting RAID arrays. [ 2.840000] md: autorun ... [ 2.840000] md: ... autorun DONE. [ 3.070000] VFS: Mounted root (jffs2 filesystem) readonly. [ 3.070000] Freeing init memory: 124K [ 3.070000] Warning: unable to open an initial console. [ 3.080000] Kernel panic - not syncing: No init found. Try passing init= option to kernel. [ 3.090000] Scheduling watchdog timeout to force reboot... U-Boot 1.1.4 (Sep 28 2009 - 11:55:23) Cloud Engines v2.0 (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: PPV2 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 CE>> CE>> CE>>
now i need to know how to fix this issue to run ARM on this box or to return to the default pogoplug image.
Waiting for your help
thanks
|
Re: PogoPlug E02 Black February 23, 2014 03:07PM |
Admin Registered: 13 years ago Posts: 18,580 |
msanad,
Looks like it's booting the stock u-Boot and stock kernel. But I think you've messed up your u-Boot envs so it can't finish starting the kernel.
At the serial console get the listing of u-Boot envs and post here.
CE>> printenv
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Looks like it's booting the stock u-Boot and stock kernel. But I think you've messed up your u-Boot envs so it can't finish starting the kernel.
At the serial console get the listing of u-Boot envs and post here.
CE>> printenv
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: PogoPlug E02 Black February 23, 2014 03:14PM |
Registered: 10 years ago Posts: 37 |
bodhi
here is the output
here is the output
CE>> printenv baudrate=115200 loads_echo=0 rootpath=/mnt/ARM_FS/ netmask=255.255.0.0 run_diag=yes console=console=ttyS0,115200 CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_root=root=/dev/mtdblock2 ro ethmtu=1500 usb0Mode=host nandEcc=1bit ethact=egiga0 bootargs=console=ttyS0,115200 root=/dev/mtdblock2 ro serverip=169.254.254.252 ipaddr=169.254.254.253 ethaddr=00:25:31:04:A2:18 cesvcid=KUPZQP73T5R3KSCL5P5T6KGACJ ceboardver=PPV2 bootcmd=nand read.e 0x800000 0x100000 0x200000; setenv bootargs $(console) $(bootargs_root); bootm 0x800000 stdin=serial stdout=serial stderr=serial mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no Environment size: 787/131068 bytes CE>>
|
Re: PogoPlug E02 Black February 23, 2014 03:55PM |
Admin Registered: 13 years ago Posts: 18,580 |
OK. I don't have the log for original u-Boot envs so can't say why it did not boot. It seems OK. Let's do this:
1. Get the latest rootfs from here and put it on a new USB thumb drive (formatted as Ext3) using another Linux box:
http://forum.doozan.com/read.php?2,12096
2. Plug in this rootfs and power up
3. Interrupt serial console, execute these setenvs (Do not save it with saveenv since you are still testing). Just copy/paste these commands to the console one-by-one
4. If there was no error in step 3, go ahead and boot:
See how it goes. If you got it booted into Debian, then the rest is easy.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
1. Get the latest rootfs from here and put it on a new USB thumb drive (formatted as Ext3) using another Linux box:
http://forum.doozan.com/read.php?2,12096
2. Plug in this rootfs and power up
3. Interrupt serial console, execute these setenvs (Do not save it with saveenv since you are still testing). Just copy/paste these commands to the console one-by-one
setenv console 'ttyS0,115200' setenv usb_device '0:1' setenv mtdparts 'mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)' setenv usb_set_bootargs 'setenv bootargs console=$console root=/dev/sda1 rootdelay=10 rootfstype=ext3 $mtdparts' setenv usb_boot 'mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi' setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot' setenv bootcmd 'usb start; run usb_bootcmd; usb stop; reset'
4. If there was no error in step 3, go ahead and boot:
boot
See how it goes. If you got it booted into Debian, then the rest is easy.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: PogoPlug E02 Black February 23, 2014 04:12PM |
Registered: 10 years ago Posts: 37 |
|
Re: PogoPlug E02 Black February 23, 2014 04:57PM |
Admin Registered: 13 years ago Posts: 18,580 |
msanad Wrote:
-------------------------------------------------------
> As i'm using Windows 7 , i'm trying to find some
> program to formate the USB flash into EXT3 , do u
> have any suggestion ??
You can get Linux Live CD and boot the PC with it.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> As i'm using Windows 7 , i'm trying to find some
> program to formate the USB flash into EXT3 , do u
> have any suggestion ??
You can get Linux Live CD and boot the PC with it.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: PogoPlug E02 Black February 23, 2014 05:02PM |
Admin Registered: 13 years ago Posts: 18,580 |
One more thing, if this causes an error:
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 02/23/2014 05:05PM by bodhi.
setenv usb_boot 'mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi'then try this instead
setenv usb_boot 'mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; ext2load usb $usb_device 0x1100000 /boot/uInitrd; bootm 0x800000 0x1100000'or
setenv usb_boot 'mw 0x800000 0 1; ext2load usb 0:1 0x800000 /boot/uImage; ext2load usb 0:1 0x1100000 /boot/uInitrd; bootm 0x800000 0x1100000'
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 02/23/2014 05:05PM by bodhi.
|
Re: PogoPlug E02 Black February 24, 2014 03:09AM |
Registered: 10 years ago Posts: 37 |
hi bodhi
i got these errors
Please check
i got these errors
CE>> setenv usb_boot 'mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi' ** Too many args (max. 16) ** CE>> setenv usb_boot 'mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; ext2load usb $usb_device 0x1100000 /boot/uInitrd; bootm 0x800000 0x1100000' ** Too many args (max. 16) ** CE>> setenv usb_boot 'mw 0x800000 0 1; ext2load usb 0:1 0x800000 /boot/uImage; ext2load usb 0:1 0x1100000 /boot/uInitrd; bootm 0x800000 0x1100000' ** Too many args (max. 16) ** CE>>
Please check
|
Re: PogoPlug E02 Black February 24, 2014 03:30AM |
Admin Registered: 13 years ago Posts: 18,580 |
I kind of expect it. The stock uBoot is quite old, so it's limited in scripting. Too bad the Pogo E02 does not have UART booting so you can try without flashing new uBoot to NAND. You could flash uBoot directly to NAND using serial console, but I don't know if you want to do that. If booting with stock u-Boot does not work, then you can try that. We'll come to that later if this does not work.
So let's break this usb_boot command in more pieces:
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
So let's break this usb_boot command in more pieces:
setenv load_uImage 'ext2load usb 0:1 0x800000 /boot/uImage' setenv load_uInitrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd setenv boot_debian 'bootm 0x800000 0x1100000' setenv usb_boot 'mw 0x800000 0 1; run load_uImage; run load_uInitrd; run boot_debian'
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: PogoPlug E02 Black February 24, 2014 03:36AM |
Registered: 10 years ago Posts: 37 |
|
Re: PogoPlug E02 Black February 24, 2014 03:40AM |
Admin Registered: 13 years ago Posts: 18,580 |
|
Re: PogoPlug E02 Black February 24, 2014 03:43AM |
Registered: 10 years ago Posts: 37 |
it seem something wrong
here is the output
here is the output
CE>> setenv load_uImage 'ext2load usb 0:1 0x800000 /boot/uImage' CE>> setenv load_uInitrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd CE>> setenv boot_debian 'bootm 0x800000 0x1100000' CE>> setenv usb_boot 'mw 0x800000 0 1; run load_uImage; run load_uInitrd; run boot_debian' CE>> setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot' CE>> setenv bootcmd 'usb start; run usb_bootcmd; usb stop; reset' CE>> CE>> CE>> boot Unknown command 'usb' - try 'help' ** Block device usb 0 not supported ** Block device usb 0 not supported ## Booting image at 00800000 ... Bad Magic Number Unknown command 'usb' - try 'help' U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: PPV2 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x100000, size 0x200000 Reading data from 0x2ff800 -- 100% complete. 2097152 bytes read: OK ## Booting image at 00800000 ... Image Name: Linux-2.6.22.18 Created: 2009-10-14 20:23:19 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1978544 Bytes = 1.9 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux............................................................................................................................ done, booting the kernel. [ 0.000000] Linux version 2.6.22.18 (bdietrich@brad-ux) (gcc version 4.2.1) #63 Wed Oct 14 13:23:16 PDT 2009 [ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177 [ 0.000000] Machine: Feroceon-KW [ 0.000000] Using UBoot passing parameters structure [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] CPU0: D VIVT write-back cache [ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] Built 1 zonelists. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro [ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes) [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 128MB 0MB 0MB 0MB = 128MB total [ 0.000000] Memory: 125824KB available (3592K code, 253K data, 124K init) [ 0.240000] Mount-cache hash table entries: 512 [ 0.240000] CPU: Testing write buffer coherency: ok [ 0.240000] NET: Registered protocol family 16 [ 0.240000] [ 0.240000] CPU Interface [ 0.240000] ------------- [ 0.240000] SDRAM_CS0 ....base 00000000, size 128MB [ 0.240000] SDRAM_CS1 ....disable [ 0.240000] SDRAM_CS2 ....disable [ 0.240000] SDRAM_CS3 ....disable [ 0.240000] PEX0_MEM ....base e8000000, size 128MB [ 0.240000] PEX0_IO ....base f2000000, size 1MB [ 0.240000] INTER_REGS ....base f1000000, size 1MB [ 0.240000] NFLASH_CS ....base fa000000, size 2MB [ 0.240000] SPI_CS ....base f4000000, size 16MB [ 0.240000] BOOT_ROM_CS ....no such [ 0.240000] DEV_BOOTCS ....no such [ 0.240000] CRYPT_ENG ....base f0000000, size 2MB [ 0.240000] [ 0.240000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21_with_rx_desc_tuned)-- SHEEVA PLUG Soc: 88F6281 A0 LE [ 0.240000] [ 0.240000] Detected Tclk 200000000 and SysClk 400000000 [ 0.240000] MV Buttons Device Load [ 0.240000] Marvell USB EHCI Host controller #0: c0539600 [ 0.740000] PEX0 interface detected no Link. [ 0.740000] PCI: bus0: Fast back to back transfers enabled [ 0.740000] SCSI subsystem initialized [ 0.740000] usbcore: registered new interface driver usbfs [ 0.740000] usbcore: registered new interface driver hub [ 0.740000] usbcore: registered new device driver usb [ 0.740000] NET: Registered protocol family 2 [ 0.750000] Time: kw_clocksource clocksource has been installed. [ 0.840000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.840000] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.840000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.840000] TCP: Hash tables configured (established 4096 bind 4096) [ 0.840000] TCP reno registered [ 0.870000] RTC has been updated!!! [ 0.870000] RTC registered [ 0.870000] Use the XOR engines (acceleration) for enhancing the following functions: [ 0.870000] o RAID 5 Xor calculation [ 0.870000] o kernel memcpy [ 0.870000] o kenrel memzero [ 0.870000] Number of XOR engines to use: 4 [ 0.870000] cesadev_init(c00116f0) [ 0.870000] mvCesaInit: sessions=640, queue=64, pSram=f0000000 [ 0.870000] MV Buttons Driver Load [ 0.870000] squashfs: version 3.3 (2007/10/31) Phillip Lougher [ 0.870000] squashfs: LZMA suppport for slax.org by jro [ 0.870000] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.870000] io scheduler noop registered [ 0.870000] io scheduler anticipatory registered (default) [ 0.890000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [ 0.890000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A [ 0.900000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize [ 0.910000] Loading Marvell Ethernet Driver: [ 0.910000] o Cached descriptors in DRAM [ 0.910000] o DRAM SW cache-coherency [ 0.920000] o Single RX Queue support - ETH_DEF_RXQ=0 [ 0.920000] o Single TX Queue support - ETH_DEF_TXQ=0 [ 0.930000] o TCP segmentation offload enabled [ 0.930000] o Receive checksum offload enabled [ 0.940000] o Transmit checksum offload enabled [ 0.940000] o Network Fast Processing (Routing) supported [ 0.950000] o Driver ERROR statistics enabled [ 0.950000] o Driver INFO statistics enabled [ 0.960000] o Proc tool API enabled [ 0.960000] o Rx descripors: q0=128 [ 0.960000] o Tx descripors: q0=532 [ 0.970000] o Loading network interface(s): [ 0.970000] o eth0, ifindex = 1, GbE port = 0 [ 0.980000] o eth1, ifindex = 2, GbE port = 1 [ 0.990000] [ 0.990000] mvFpRuleDb (c7ed4000): 1024 entries, 4096 bytes [ 0.990000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI [ 1.000000] Copyright (c) 1999-2006 Intel Corporation. [ 1.010000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI [ 1.010000] e100: Copyright(c) 1999-2006 Intel Corporation [ 1.020000] [ 1.020000] Warning Sata is Powered Off [ 1.020000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ [ 1.030000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit) [ 1.040000] Scanning device for bad blocks [ 1.090000] Using static partition definition [ 1.100000] Creating 4 MTD partitions on "nand_mtd": [ 1.100000] 0x00000000-0x00100000 : "u-boot" [ 1.110000] 0x00100000-0x00500000 : "uImage" [ 1.110000] 0x00500000-0x02500000 : "root" [ 1.120000] 0x02500000-0x08000000 : "data" [ 1.120000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI [ 1.130000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 [ 1.170000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 [ 1.190000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 1.190000] usb usb1: configuration #1 chosen from 1 choice [ 1.200000] hub 1-0:1.0: USB hub found [ 1.200000] hub 1-0:1.0: 1 port detected [ 1.320000] USB Universal Host Controller Interface driver v3.0 [ 1.600000] usb 1-1: new high speed USB device using ehci_marvell and address 2 [ 1.750000] usb 1-1: configuration #1 chosen from 1 choice [ 1.750000] hub 1-1:1.0: USB hub found [ 1.760000] hub 1-1:1.0: 4 ports detected [ 2.110000] usb 1-1.3: new high speed USB device using ehci_marvell and address 3 [ 2.210000] usb 1-1.3: configuration #1 chosen from 1 choice [ 2.220000] usbcore: registered new interface driver usblp [ 2.220000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver [ 2.230000] Initializing USB Mass Storage driver... [ 2.240000] scsi0 : SCSI emulation for USB Mass Storage devices [ 2.240000] usbcore: registered new interface driver usb-storage [ 2.250000] USB Mass Storage support registered. [ 2.250000] mice: PS/2 mouse device common for all mice [ 2.260000] i2c /dev entries driver [ 2.260000] Linux telephony interface: v1.00 [ 2.270000] md: linear personality registered for level -1 [ 2.270000] md: raid0 personality registered for level 0 [ 2.280000] md: raid1 personality registered for level 1 [ 2.450000] raid6: int32x1 97 MB/s [ 2.620000] raid6: int32x2 114 MB/s [ 2.790000] raid6: int32x4 122 MB/s [ 2.960000] raid6: int32x8 110 MB/s [ 2.960000] raid6: using algorithm int32x4 (122 MB/s) [ 2.960000] md: raid6 personality registered for level 6 [ 2.970000] md: raid5 personality registered for level 5 [ 2.970000] md: raid4 personality registered for level 4 [ 2.980000] raid5: measuring checksumming speed [ 3.030000] arm4regs : 1071.600 MB/sec [ 3.080000] 8regs : 754.800 MB/sec [ 3.130000] 32regs : 899.600 MB/sec [ 3.130000] raid5: using function: arm4regs (1071.600 MB/sec) [ 3.140000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com [ 3.140000] dm_crypt using the OCF package. [ 3.150000] sdhci: Secure Digital Host Controller Interface driver [ 3.150000] sdhci: Copyright(c) Pierre Ossman [ 3.160000] usbcore: registered new interface driver usbhid [ 3.160000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 3.170000] TCP cubic registered [ 3.170000] NET: Registered protocol family 1 [ 3.180000] NET: Registered protocol family 17 [ 3.180000] md: Autodetecting RAID arrays. [ 3.190000] md: autorun ... [ 3.190000] md: ... autorun DONE. [ 3.420000] VFS: Mounted root (jffs2 filesystem) readonly. [ 3.420000] Freeing init memory: 124K [ 3.420000] Warning: unable to open an initial console. [ 3.430000] Kernel panic - not syncing: No init found. Try passing init= option to kernel. [ 3.440000] Scheduling watchdog timeout to force reboot... U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: PPV2 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0
|
Re: PogoPlug E02 Black February 24, 2014 03:56PM |
Admin Registered: 13 years ago Posts: 18,580 |
Strange! Try running
CE>> help
at the prompt to see what commands are available.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
CE>> help
at the prompt to see what commands are available.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: PogoPlug E02 Black February 25, 2014 03:27AM |
Registered: 10 years ago Posts: 37 |
Here is the Output of help
U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: PPV2 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 CE>> CE>> CE>> CE>> CE>> CE>> CE>> CE>> CE>> CE>> CE>> CE>> CE>> CE>> help ? - alias for 'help' base - print or set address offset boot - boot default, i.e., run 'bootcmd' bootd - boot default, i.e., run 'bootcmd' bootext2 dev:boot_part1,boot_part2 addr boot_image linux_dev_name bootm - boot application image from memory bootp - boot image via network using BootP/TFTP protocol bubt - Burn an image on the Boot Nand Flash. chpart - change active partition cmp - memory compare cmpm - Compare Memory cp - memory copy cpumap - Display CPU memory mapping settings. crc32 - checksum calculation date - get/set/reset date & time dclk - Display the MV device CLKs. dhcp - invoke DHCP client to obtain IP/boot params diskboot- boot from IDE device echo - echo args to console eeprom - EEPROM sub-system erase - erase FLASH memory ext2load- load binary file from a Ext2 filesystem ext2ls - list files in a directory (default /) fi - Find value in the memory. flinfo - print FLASH memory information fsinfo - print information about filesystems fsload - load binary file from a filesystem image g - start application at cached address 'addr'(default addr 0x40000) go - start application at address 'addr' help - print online help icrc32 - checksum calculation ide - IDE sub-system iloop - infinite loop on address range imd - i2c memory display imm[.b, .s, .w, .l] - i2c memory modify (auto-incrementing) imw - memory write (fill) inm - memory modify (constant address) iprobe - probe to discover valid I2C chip addresses ir - reading and changing MV internal register values. loop - infinite loop on address range ls - list files in a directory (default /) map - Diasplay address decode windows md - memory display me - PCI master enable mm - memory modify (auto-incrementing) mp - map PCI BAR mtdparts- define flash/nand partitions mtest - simple RAM test mv_diag - perform board diagnostics mw - memory write (fill) nand - NAND sub-system nboot - boot from NAND device nbubt - Burn a boot loader image on the Boot Nand Flash. nm - memory modify (constant address) pci - list and access PCI Configuration Space phyRead - Read PCI-E Phy register pciePhyWrite - Write PCI-E Phy register phyRead - Read Phy register phyWrite - Write Phy register ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables protect - enable or disable FLASH write protection rarpboot- boot image via network using RARP/TFTP protocol reset - Perform RESET of the CPU resetenv - Return all environment variable to default. run - run commands in an environment variable saveenv - save environment variables to persistent storage se - PCI Slave enable setenv - set environment variables sflash - read, write or erase the external SPI Flash. sg - scanning the PHYs status sp - Scan PCI bus. tftpboot- boot image via network using TFTP protocol version - print monitor version
|
Re: PogoPlug E02 Black February 26, 2014 08:39AM |
Registered: 10 years ago Posts: 37 |
|
Re: PogoPlug E02 Black February 26, 2014 10:43AM |
Registered: 11 years ago Posts: 232 |
|
Re: PogoPlug E02 Black February 26, 2014 04:38PM |
Admin Registered: 13 years ago Posts: 18,580 |
Looks like this stock uboot does not have usb command. And as WarheadsSE said, rootfs in Nand was corrupted.
You have 2 choices, either:
1. Try to restore rootfs with a backup dump, from a good unit.
2. Flash new uboot so you can boot with usb. Setup tftp server on the box that you use to monitor serialconsole. And use tftp command to load new uboot image, and flash it.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
You have 2 choices, either:
1. Try to restore rootfs with a backup dump, from a good unit.
2. Flash new uboot so you can boot with usb. Setup tftp server on the box that you use to monitor serialconsole. And use tftp command to load new uboot image, and flash it.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: PogoPlug E02 Black March 02, 2014 06:33AM |
Registered: 10 years ago Posts: 37 |
bodhi Wrote:
-------------------------------------------------------
> Looks like this stock uboot does not have usb
> command. And as WarheadsSE said, rootfs in Nand
> was corrupted.
>
> You have 2 choices, either:
> 1. Try to restore rootfs with a backup dump, from
> a good unit.
> 2. Flash new uboot so you can boot with usb. Setup
> tftp server on the box that you use to monitor
> serialconsole. And use tftp command to load new
> uboot image, and flash it.
As i dont Have alot of experince with Unix , could you help me in either choice , i think the second one i applicable as i already have tftp and work with Pogoplug E02 before and have serial connection with the box.
-------------------------------------------------------
> Looks like this stock uboot does not have usb
> command. And as WarheadsSE said, rootfs in Nand
> was corrupted.
>
> You have 2 choices, either:
> 1. Try to restore rootfs with a backup dump, from
> a good unit.
> 2. Flash new uboot so you can boot with usb. Setup
> tftp server on the box that you use to monitor
> serialconsole. And use tftp command to load new
> uboot image, and flash it.
As i dont Have alot of experince with Unix , could you help me in either choice , i think the second one i applicable as i already have tftp and work with Pogoplug E02 before and have serial connection with the box.
|
Re: PogoPlug E02 Black March 02, 2014 03:32PM |
Admin Registered: 13 years ago Posts: 18,580 |
msanad,
Be careful when you flash u-Boot with Pogo E02 because if something goes wrong during flashing (typos, power outage,…) then the only way to recover is JTAG.
You can download the latest Pogo E02 u-Boot from here:
http://forum.doozan.com/read.php?3,12381
And then follow the instruction here:
http://forum.doozan.com/read.php?3,14916,14917#msg-14917
Note about uboot.kwb image referred to in the instruction thread above: is the uBoot image retrieved by Jeff script (http://projects.doozan.com/uboot/install_uboot_mtd0.sh)
In this case, replace that with the u-Boot image you will download: uboot.2013.10.tld-2.pogo_e02.mtd0.kwb
Update 1: make sure there is no bad block in the first 1M of your NAND. If there is, don't flash U-Boot just yet. You will need plan B.
Update 2: I just looked at your original dmesg. It seems there is no bad block! so you're good to proceed.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 4 time(s). Last edit at 03/02/2014 03:41PM by bodhi.
Be careful when you flash u-Boot with Pogo E02 because if something goes wrong during flashing (typos, power outage,…) then the only way to recover is JTAG.
You can download the latest Pogo E02 u-Boot from here:
http://forum.doozan.com/read.php?3,12381
And then follow the instruction here:
http://forum.doozan.com/read.php?3,14916,14917#msg-14917
Note about uboot.kwb image referred to in the instruction thread above: is the uBoot image retrieved by Jeff script (http://projects.doozan.com/uboot/install_uboot_mtd0.sh)
In this case, replace that with the u-Boot image you will download: uboot.2013.10.tld-2.pogo_e02.mtd0.kwb
Update 1: make sure there is no bad block in the first 1M of your NAND. If there is, don't flash U-Boot just yet. You will need plan B.
Update 2: I just looked at your original dmesg. It seems there is no bad block! so you're good to proceed.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 4 time(s). Last edit at 03/02/2014 03:41PM by bodhi.
|
Re: PogoPlug E02 Black March 03, 2014 01:44PM |
Registered: 10 years ago Posts: 37 |
Well , I have download the Uboot Image and follow the instruction in the post here : http://forum.doozan.com/read.php?3,14916,14917#msg-14917
after flashing and erasing the NAND then write it again and after make boot commad , the kernal load till this line Scheduling watchdog timeout to force reboot...
but after while (few seconds) it load again but this time stops at
then i made saveenv because i see this line WARNING: Caches not enabled
but still stops at Starting kernel ...
The prompt name changed to PogoE02>
i made it restart by pressing the on-board bottom which make it start booting from the begaining.
here is all logs
loading the new Uboot
Saving the Env and boot again
Here is the Help output
Print Env output
Waiting for your feedback
after flashing and erasing the NAND then write it again and after make boot commad , the kernal load till this line Scheduling watchdog timeout to force reboot...
but after while (few seconds) it load again but this time stops at
Starting kernel ... Uncompressing Linux............................................................................................................................ done, booting the kernel.
then i made saveenv because i see this line WARNING: Caches not enabled
but still stops at Starting kernel ...
Uncompressing Linux............................................................................................................................ done, booting the kernel.
The prompt name changed to PogoE02>
i made it restart by pressing the on-board bottom which make it start booting from the begaining.
here is all logs
Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x100000, size 0x200000 Reading data from 0x2d1800 -- 91% complete. U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: PPV2 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x100000, size 0x200000 Reading data from 0x2ff800 -- 100% complete. 2097152 bytes read: OK ## Booting image at 00800000 ... Image Name: Linux-2.6.22.18 Created: 2009-10-14 20:23:19 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1978544 Bytes = 1.9 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux............................................................................................................................ done, booting the kernel. [ 0.000000] Linux version 2.6.22.18 (bdietrich@brad-ux) (gcc version 4.2.1) #63 Wed Oct 14 13:23:16 PDT 2009 [ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177 [ 0.000000] Machine: Feroceon-KW [ 0.000000] Using UBoot passing parameters structure [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] CPU0: D VIVT write-back cache [ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] Built 1 zonelists. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro [ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes) [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 128MB 0MB 0MB 0MB = 128MB total [ 0.000000] Memory: 125824KB available (3592K code, 253K data, 124K init) [ 0.240000] Mount-cache hash table entries: 512 [ 0.240000] CPU: Testing write buffer coherency: ok [ 0.240000] NET: Registered protocol family 16 [ 0.240000] [ 0.240000] CPU Interface [ 0.240000] ------------- [ 0.240000] SDRAM_CS0 ....base 00000000, size 128MB [ 0.240000] SDRAM_CS1 ....disable [ 0.240000] SDRAM_CS2 ....disable [ 0.240000] SDRAM_CS3 ....disable [ 0.240000] PEX0_MEM ....base e8000000, size 128MB [ 0.240000] PEX0_IO ....base f2000000, size 1MB [ 0.240000] INTER_REGS ....base f1000000, size 1MB [ 0.240000] NFLASH_CS ....base fa000000, size 2MB [ 0.240000] SPI_CS ....base f4000000, size 16MB [ 0.240000] BOOT_ROM_CS ....no such [ 0.240000] DEV_BOOTCS ....no such [ 0.240000] CRYPT_ENG ....base f0000000, size 2MB [ 0.240000] [ 0.240000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21_with_rx_desc_tuned)-- SHEEVA PLUG Soc: 88F6281 A0 LE [ 0.240000] [ 0.240000] Detected Tclk 200000000 and SysClk 400000000 [ 0.240000] MV Buttons Device Load [ 0.240000] Marvell USB EHCI Host controller #0: c0539600 [ 0.740000] PEX0 interface detected no Link. [ 0.740000] PCI: bus0: Fast back to back transfers enabled [ 0.740000] SCSI subsystem initialized [ 0.740000] usbcore: registered new interface driver usbfs [ 0.740000] usbcore: registered new interface driver hub [ 0.740000] usbcore: registered new device driver usb [ 0.740000] NET: Registered protocol family 2 [ 0.750000] Time: kw_clocksource clocksource has been installed. [ 0.840000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.840000] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.840000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.840000] TCP: Hash tables configured (established 4096 bind 4096) [ 0.840000] TCP reno registered [ 0.870000] RTC has been updated!!! [ 0.870000] RTC registered [ 0.870000] Use the XOR engines (acceleration) for enhancing the following functions: [ 0.870000] o RAID 5 Xor calculation [ 0.870000] o kernel memcpy [ 0.870000] o kenrel memzero [ 0.870000] Number of XOR engines to use: 4 [ 0.870000] cesadev_init(c00116f0) [ 0.870000] mvCesaInit: sessions=640, queue=64, pSram=f0000000 [ 0.870000] MV Buttons Driver Load [ 0.870000] squashfs: version 3.3 (2007/10/31) Phillip Lougher [ 0.870000] squashfs: LZMA suppport for slax.org by jro [ 0.870000] JFFS2 version 2.2. (NAND) أ‚آ© 2001-2006 Red Hat, Inc. [ 0.870000] io scheduler noop registered [ 0.870000] io scheduler anticipatory registered (default) [ 0.890000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [ 0.890000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A [ 0.900000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize [ 0.910000] Loading Marvell Ethernet Driver: [ 0.910000] o Cached descriptors in DRAM [ 0.910000] o DRAM SW cache-coherency [ 0.920000] o Single RX Queue support - ETH_DEF_RXQ=0 [ 0.920000] o Single TX Queue support - ETH_DEF_TXQ=0 [ 0.930000] o TCP segmentation offload enabled [ 0.930000] o Receive checksum offload enabled [ 0.940000] o Transmit checksum offload enabled [ 0.940000] o Network Fast Processing (Routing) supported [ 0.950000] o Driver ERROR statistics enabled [ 0.950000] o Driver INFO statistics enabled [ 0.960000] o Proc tool API enabled [ 0.960000] o Rx descripors: q0=128 [ 0.960000] o Tx descripors: q0=532 [ 0.970000] o Loading network interface(s): [ 0.970000] o eth0, ifindex = 1, GbE port = 0 [ 0.980000] o eth1, ifindex = 2, GbE port = 1 [ 0.990000] [ 0.990000] mvFpRuleDb (c7ed4000): 1024 entries, 4096 bytes [ 0.990000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI [ 1.000000] Copyright (c) 1999-2006 Intel Corporation. [ 1.010000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI [ 1.010000] e100: Copyright(c) 1999-2006 Intel Corporation [ 1.020000] [ 1.020000] Warning Sata is Powered Off [ 1.020000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ [ 1.030000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit) [ 1.040000] Scanning device for bad blocks [ 1.090000] Using static partition definition [ 1.100000] Creating 4 MTD partitions on "nand_mtd": [ 1.100000] 0x00000000-0x00100000 : "u-boot" [ 1.110000] 0x00100000-0x00500000 : "uImage" [ 1.110000] 0x00500000-0x02500000 : "root" [ 1.120000] 0x02500000-0x08000000 : "data" [ 1.120000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI [ 1.130000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 [ 1.170000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 [ 1.190000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 1.190000] usb usb1: configuration #1 chosen from 1 choice [ 1.200000] hub 1-0:1.0: USB hub found [ 1.200000] hub 1-0:1.0: 1 port detected [ 1.320000] USB Universal Host Controller Interface driver v3.0 [ 1.600000] usb 1-1: new high speed USB device using ehci_marvell and address 2 [ 1.750000] usb 1-1: configuration #1 chosen from 1 choice [ 1.750000] hub 1-1:1.0: USB hub found [ 1.760000] hub 1-1:1.0: 4 ports detected [ 1.870000] usbcore: registered new interface driver usblp [ 1.870000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver [ 1.880000] Initializing USB Mass Storage driver... [ 1.880000] usbcore: registered new interface driver usb-storage [ 1.890000] USB Mass Storage support registered. [ 1.900000] mice: PS/2 mouse device common for all mice [ 1.900000] i2c /dev entries driver [ 1.900000] Linux telephony interface: v1.00 [ 1.910000] md: linear personality registered for level -1 [ 1.910000] md: raid0 personality registered for level 0 [ 1.920000] md: raid1 personality registered for level 1 [ 2.090000] raid6: int32x1 97 MB/s [ 2.260000] raid6: int32x2 114 MB/s [ 2.430000] raid6: int32x4 122 MB/s [ 2.600000] raid6: int32x8 110 MB/s [ 2.600000] raid6: using algorithm int32x4 (122 MB/s) [ 2.600000] md: raid6 personality registered for level 6 [ 2.610000] md: raid5 personality registered for level 5 [ 2.610000] md: raid4 personality registered for level 4 [ 2.620000] raid5: measuring checksumming speed [ 2.670000] arm4regs : 1084.000 MB/sec [ 2.720000] 8regs : 754.800 MB/sec [ 2.770000] 32regs : 900.000 MB/sec [ 2.770000] raid5: using function: arm4regs (1084.000 MB/sec) [ 2.780000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com [ 2.780000] dm_crypt using the OCF package. [ 2.790000] sdhci: Secure Digital Host Controller Interface driver [ 2.790000] sdhci: Copyright(c) Pierre Ossman [ 2.800000] usbcore: registered new interface driver usbhid [ 2.800000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 2.810000] TCP cubic registered [ 2.810000] NET: Registered protocol family 1 [ 2.820000] NET: Registered protocol family 17 [ 2.820000] md: Autodetecting RAID arrays. [ 2.830000] md: autorun ... [ 2.830000] md: ... autorun DONE. [ 3.060000] VFS: Mounted root (jffs2 filesystem) readonly. [ 3.060000] Freeing init memory: 124K [ 3.060000] Warning: unable to open an initial console. [ 3.070000] Kernel panic - not syncing: No init found. Try passing init= option to kernel. [ 3.080000] Scheduling watchdog timeout to force reboot... U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: PPV2 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x100000, size 0x200000 Reading data from 0x2ff800 -- 100% complete. 2097152 bytes read: OK ## Booting image at 00800000 ... Image Name: Linux-2.6.22.18 Created: 2009-10-14 20:23:19 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1978544 Bytes = 1.9 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux............................................................................................................................ done, booting the kernel. U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: PPV2 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 CE>> CE>> CE>> CE>> CE>> CE>> CE>> CE>> CE>> CE>>
loading the new Uboot
CE>> setenv serverip 192.168.1.2
CE>> setenv ipaddr 192.168.1.3
CE>> tftp 0x800000 uboot.2013.10.tld-2.pogo_e02.mtd0.kwb
Using egiga0 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.3
Filename 'uboot.2013.10.tld-2.pogo_e02.mtd0.kwb'.
Load address: 0x800000
Loading: #################################################################
######################################
done
Bytes transferred = 524288 (80000 hex)
CE>> nand erase 0x0 0x80000
NAND erase: device 0 offset 0x0, size 0x80000
Erasing at 0x60000 -- 100% complete.
OK
CE>> nand write.e 0x800000 0x0 0x80000
NAND write: device 0 offset 0x0, size 0x80000
Writing data at 0x7f800 -- 100% complete.
524288 bytes written: OK
CE>> boot
NAND read: device 0 offset 0x100000, size 0x200000
Reading data from 0x2ff800 -- 100% complete.
2097152 bytes read: OK
## Booting image at 00800000 ...
Image Name: Linux-2.6.22.18
Created: 2009-10-14 20:23:19 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1978544 Bytes = 1.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux............................................................................................................................ done, booting the kernel.
[ 0.000000] Linux version 2.6.22.18 (bdietrich@brad-ux) (gcc version 4.2.1) #63 Wed Oct 14 13:23:16 PDT 2009
[ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177
[ 0.000000] Machine: Feroceon-KW
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] CPU0: D VIVT write-back cache
[ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[ 0.000000] Built 1 zonelists. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 128MB 0MB 0MB 0MB = 128MB total
[ 0.000000] Memory: 125824KB available (3592K code, 253K data, 124K init)
[ 0.240000] Mount-cache hash table entries: 512
[ 0.240000] CPU: Testing write buffer coherency: ok
[ 0.240000] NET: Registered protocol family 16
[ 0.240000]
[ 0.240000] CPU Interface
[ 0.240000] -------------
[ 0.240000] SDRAM_CS0 ....base 00000000, size 128MB
[ 0.240000] SDRAM_CS1 ....disable
[ 0.240000] SDRAM_CS2 ....disable
[ 0.240000] SDRAM_CS3 ....disable
[ 0.240000] PEX0_MEM ....base e8000000, size 128MB
[ 0.240000] PEX0_IO ....base f2000000, size 1MB
[ 0.240000] INTER_REGS ....base f1000000, size 1MB
[ 0.240000] NFLASH_CS ....base fa000000, size 2MB
[ 0.240000] SPI_CS ....base f4000000, size 16MB
[ 0.240000] BOOT_ROM_CS ....no such
[ 0.240000] DEV_BOOTCS ....no such
[ 0.240000] CRYPT_ENG ....base f0000000, size 2MB
[ 0.240000]
[ 0.240000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21_with_rx_desc_tuned)-- SHEEVA PLUG Soc: 88F6281 A0 LE
[ 0.240000]
[ 0.240000] Detected Tclk 200000000 and SysClk 400000000
[ 0.240000] MV Buttons Device Load
[ 0.240000] Marvell USB EHCI Host controller #0: c0539600
[ 0.740000] PEX0 interface detected no Link.
[ 0.740000] PCI: bus0: Fast back to back transfers enabled
[ 0.740000] SCSI subsystem initialized
[ 0.740000] usbcore: registered new interface driver usbfs
[ 0.740000] usbcore: registered new interface driver hub
[ 0.740000] usbcore: registered new device driver usb
[ 0.740000] NET: Registered protocol family 2
[ 0.750000] Time: kw_clocksource clocksource has been installed.
[ 0.840000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.840000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.840000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.840000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.840000] TCP reno registered
[ 0.870000] RTC has been updated!!!
[ 0.870000] RTC registered
[ 0.870000] Use the XOR engines (acceleration) for enhancing the following functions:
[ 0.870000] o RAID 5 Xor calculation
[ 0.870000] o kernel memcpy
[ 0.870000] o kenrel memzero
[ 0.870000] Number of XOR engines to use: 4
[ 0.870000] cesadev_init(c00116f0)
[ 0.870000] mvCesaInit: sessions=640, queue=64, pSram=f0000000
[ 0.870000] MV Buttons Driver Load
[ 0.870000] squashfs: version 3.3 (2007/10/31) Phillip Lougher
[ 0.870000] squashfs: LZMA suppport for slax.org by jro
[ 0.870000] JFFS2 version 2.2. (NAND) أ‚آ© 2001-2006 Red Hat, Inc.
[ 0.870000] io scheduler noop registered
[ 0.870000] io scheduler anticipatory registered (default)
[ 0.890000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
[ 0.890000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 0.900000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
[ 0.910000] Loading Marvell Ethernet Driver:
[ 0.910000] o Cached descriptors in DRAM
[ 0.910000] o DRAM SW cache-coherency
[ 0.920000] o Single RX Queue support - ETH_DEF_RXQ=0
[ 0.920000] o Single TX Queue support - ETH_DEF_TXQ=0
[ 0.930000] o TCP segmentation offload enabled
[ 0.930000] o Receive checksum offload enabled
[ 0.940000] o Transmit checksum offload enabled
[ 0.940000] o Network Fast Processing (Routing) supported
[ 0.950000] o Driver ERROR statistics enabled
[ 0.950000] o Driver INFO statistics enabled
[ 0.960000] o Proc tool API enabled
[ 0.960000] o Rx descripors: q0=128
[ 0.960000] o Tx descripors: q0=532
[ 0.970000] o Loading network interface(s):
[ 0.970000] o eth0, ifindex = 1, GbE port = 0
[ 0.980000] o eth1, ifindex = 2, GbE port = 1
[ 0.990000]
[ 0.990000] mvFpRuleDb (c7ed4000): 1024 entries, 4096 bytes
[ 0.990000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
[ 1.000000] Copyright (c) 1999-2006 Intel Corporation.
[ 1.010000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
[ 1.010000] e100: Copyright(c) 1999-2006 Intel Corporation
[ 1.020000]
[ 1.020000] Warning Sata is Powered Off
[ 1.020000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
[ 1.030000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit)
[ 1.040000] Scanning device for bad blocks
[ 1.090000] Using static partition definition
[ 1.100000] Creating 4 MTD partitions on "nand_mtd":
[ 1.100000] 0x00000000-0x00100000 : "u-boot"
[ 1.110000] 0x00100000-0x00500000 : "uImage"
[ 1.110000] 0x00500000-0x02500000 : "root"
[ 1.120000] 0x02500000-0x08000000 : "data"
[ 1.120000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
[ 1.130000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
[ 1.170000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
[ 1.190000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 1.190000] usb usb1: configuration #1 chosen from 1 choice
[ 1.200000] hub 1-0:1.0: USB hub found
[ 1.200000] hub 1-0:1.0: 1 port detected
[ 1.320000] USB Universal Host Controller Interface driver v3.0
[ 1.600000] usb 1-1: new high speed USB device using ehci_marvell and address 2
[ 1.750000] usb 1-1: configuration #1 chosen from 1 choice
[ 1.750000] hub 1-1:1.0: USB hub found
[ 1.760000] hub 1-1:1.0: 4 ports detected
[ 1.870000] usbcore: registered new interface driver usblp
[ 1.870000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[ 1.880000] Initializing USB Mass Storage driver...
[ 1.880000] usbcore: registered new interface driver usb-storage
[ 1.890000] USB Mass Storage support registered.
[ 1.900000] mice: PS/2 mouse device common for all mice
[ 1.900000] i2c /dev entries driver
[ 1.900000] Linux telephony interface: v1.00
[ 1.910000] md: linear personality registered for level -1
[ 1.910000] md: raid0 personality registered for level 0
[ 1.920000] md: raid1 personality registered for level 1
[ 2.090000] raid6: int32x1 97 MB/s
[ 2.260000] raid6: int32x2 114 MB/s
[ 2.430000] raid6: int32x4 122 MB/s
[ 2.600000] raid6: int32x8 110 MB/s
[ 2.600000] raid6: using algorithm int32x4 (122 MB/s)
[ 2.600000] md: raid6 personality registered for level 6
[ 2.610000] md: raid5 personality registered for level 5
[ 2.610000] md: raid4 personality registered for level 4
[ 2.620000] raid5: measuring checksumming speed
[ 2.670000] arm4regs : 1071.600 MB/sec
[ 2.720000] 8regs : 754.800 MB/sec
[ 2.770000] 32regs : 900.000 MB/sec
[ 2.770000] raid5: using function: arm4regs (1071.600 MB/sec)
[ 2.780000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
[ 2.780000] dm_crypt using the OCF package.
[ 2.790000] sdhci: Secure Digital Host Controller Interface driver
[ 2.790000] sdhci: Copyright(c) Pierre Ossman
[ 2.800000] usbcore: registered new interface driver usbhid
[ 2.800000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 2.810000] TCP cubic registered
[ 2.810000] NET: Registered protocol family 1
[ 2.820000] NET: Registered protocol family 17
[ 2.820000] md: Autodetecting RAID arrays.
[ 2.830000] md: autorun ...
[ 2.830000] md: ... autorun DONE.
[ 3.060000] VFS: Mounted root (jffs2 filesystem) readonly.
[ 3.060000] Freeing init memory: 124K
[ 3.060000] Warning: unable to open an initial console.
[ 3.070000] Kernel panic - not syncing: No init found. Try passing init= option to kernel.
[ 3.080000] Scheduling watchdog timeout to force reboot...
U-Boot 2013.10 (Feb 21 2014 - 19:35:02)-tld-2
Pogo E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x100000, size 0x300000
3145728 bytes read: OK
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-2.6.22.18
Created: 2009-10-14 20:23:19 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1978544 Bytes = 1.9 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
Uncompressing Linux............................................................................................................................ done, booting the kernel.
U-Boot 2013.10 (Feb 21 2014 - 19:35:02)-tld-2
Pogo E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
Hit any key to stop autoboot: 0
PogoE02>
PogoE02>
Saving the Env and boot again
PogoE02> saveenv Saving Environment to NAND... Erasing NAND... Erasing at 0xc0000 -- 100% complete. Writing to NAND... OK PogoE02> PogoE02> PogoE02> boot NAND read: device 0 offset 0x100000, size 0x300000 3145728 bytes read: OK ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-2.6.22.18 Created: 2009-10-14 20:23:19 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1978544 Bytes = 1.9 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... Uncompressing Linux............................................................................................................................ done, booting the kernel. U-Boot 2013.10 (Feb 21 2014 - 19:35:02)-tld-2 Pogo E02 SoC: Kirkwood 88F6281_A0 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x100000, size 0x300000 3145728 bytes read: OK ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-2.6.22.18 Created: 2009-10-14 20:23:19 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1978544 Bytes = 1.9 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... Uncompressing Linux............................................................................................................................ done, booting the kernel. U-Boot 2013.10 (Feb 21 2014 - 19:35:02)-tld-2 Pogo E02 SoC: Kirkwood 88F6281_A0 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 PogoE02> PogoE02> PogoE02> PogoE02> PogoE02>
Here is the Help output
PogoE02> help ? - alias for 'help' base - print or set address offset bdinfo - print Board Info structure boot - boot default, i.e., run 'bootcmd' bootd - boot default, i.e., run 'bootcmd' bootm - boot application image from memory bootp - boot image via network using BOOTP/TFTP protocol chpart - change active partition cmp - memory compare coninfo - print console devices and information cp - memory copy crc32 - checksum calculation date - get/set/reset date & time dhcp - boot image via network using DHCP/TFTP protocol dns - lookup the IP of a hostname echo - echo args to console editenv - edit environment variable env - environment handling commands exit - exit script ext2load- load binary file from a Ext2 filesystem ext2ls - list files in a directory (default /) ext4load- load binary file from a Ext4 filesystem ext4ls - list files in a directory (default /) false - do nothing, unsuccessfully fatinfo - print information about filesystem fatload - load binary file from a dos filesystem fatls - list files in a directory (default /) fdt - flattened device tree utility commands fsinfo - print information about filesystems fsload - load binary file from a filesystem image go - start application at address 'addr' help - print command description/usage iminfo - print header information for application image imxtract- extract a part of a multi-image itest - return true/false on integer compare loadb - load binary file over serial line (kermit mode) loads - load S-Record file over serial line loadx - load binary file over serial line (xmodem mode) loady - load binary file over serial line (ymodem mode) loop - infinite loop on address range ls - list files in a directory (default /) md - memory display mii - MII utility commands mm - memory modify (auto-incrementing address) mtdparts- define flash/nand partitions mw - memory write (fill) nand - NAND sub-system nboot - boot from NAND device nfs - boot image via network using NFS protocol nm - memory modify (constant address) ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables reset - Perform RESET of the CPU run - run commands in an environment variable saveenv - save environment variables to persistent storage setenv - set environment variables showvar - print local hushshell variables sleep - delay execution for some time sntp - synchronize RTC via network source - run script from memory test - minimal test like /bin/sh tftpboot- boot image via network using TFTP protocol true - do nothing, successfully ubi - ubi commands ubifsload- load file from an UBIFS filesystem ubifsls - list files in a directory ubifsmount- mount UBIFS volume ubifsumount- unmount UBIFS volume usb - USB sub-system usbboot - boot from USB device version - print monitor, compiler and linker version
Print Env output
PogoE02> printenv arcNumber=2097 baudrate=115200 bootargs_root=root=/dev/mtdblock2 ro bootcmd=nand read.e 0x800000 0x100000 0x300000; setenv bootargs $(console) $(bootargs_root); bootm 0x800000 bootcmd_pogo=fsload uboot-original-mtd0.kwb; go 0x800200 bootcmd_usb=run usb_init; run usb_load_uimage; run set_bootargs_usb; run usb_boot; bootdelay=3 console=console=ttyS0,115200 ethact=egiga0 ethaddr=00:25:31:04:A2:18 ipaddr=192.168.1.4 led_error=orange blinking led_exit=green off led_init=green blinking mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) partition=nand0,2 serverip=192.168.1.3 set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts stderr=serial stdin=serial stdout=serial usb_boot=if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000;else bootm 0x800000;fi; usb_device=0:1 usb_init=usb start usb_load_uimage=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage usb_root=/dev/sda1 usb_rootdelay=10 usb_rootfstype=ext2 Environment size: 1152/131068 bytes
Waiting for your feedback
|
Re: PogoPlug E02 Black March 03, 2014 04:39PM |
Admin Registered: 13 years ago Posts: 18,580 |
Congrats! You're running with the latest UBoot.
However, your rootfs in Nand seems to be no good. Use a new USB thumb dive, put the latest Debian rootfs on and boot with it. See link in my signature to download rootfs and instruction.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
However, your rootfs in Nand seems to be no good. Use a new USB thumb dive, put the latest Debian rootfs on and boot with it. See link in my signature to download rootfs and instruction.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: PogoPlug E02 Black March 04, 2014 02:43PM |
Registered: 10 years ago Posts: 37 |
OK fine
Now i have formate USB Flash Memory and put the latest rootfs on it , then insert it the the front USB port on Pogo plug
and exceute the following commands
here is the logs
Then what ??
Now i have formate USB Flash Memory and put the latest rootfs on it , then insert it the the front USB port on Pogo plug
and exceute the following commands
setenv console 'ttyS0,115200' setenv usb_device '0:1' setenv mtdparts 'mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)' setenv usb_set_bootargs 'setenv bootargs console=$console root=/dev/sda1 rootdelay=10 rootfstype=ext3 $mtdparts' setenv usb_boot 'mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi' setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot' setenv bootcmd 'usb start; run usb_bootcmd; usb stop; reset'
boot
here is the logs
U-Boot 2013.10 (Feb 21 2014 - 19:35:02)-tld-2
Pogo E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
Hit any key to stop autoboot: 0
PogoE02>
PogoE02>
PogoE02>
PogoE02>
PogoE02>
PogoE02> setenv console 'ttyS0,115200'
PogoE02> setenv usb_device '0:1'
PogoE02> setenv mtdparts 'mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)'
PogoE02> setenv usb_set_bootargs 'setenv bootargs console=$console root=/dev/sda1 rootdelay=10 rootfstype=ext3 $mtdparts'
PogoE02> setenv usb_boot 'mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi'
PogoE02> setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot'
PogoE02> setenv bootcmd 'usb start; run usb_bootcmd; usb stop; reset'
PogoE02> boot
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
2399792 bytes read in 362 ms (6.3 MiB/s)
6568066 bytes read in 599 ms (10.5 MiB/s)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-3.13.1-kirkwood-tld-2
Created: 2014-02-05 19:30:49 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2399728 Bytes = 2.3 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-3.13.1-kirkwood-tld-2
Created: 2014-02-05 19:31:01 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 6568002 Bytes = 6.3 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.13.1-kirkwood-tld-2 (root@tldDebian) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 PREEMPT Tue Feb 4 03:19:07 PST 2014
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Pogoplug E02
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext3 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 246168K/262144K available (4659K kernel code, 346K rwdata, 1588K rodata, 211K init, 425K bss, 15976K reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06220ac (6249 kB)
[ 0.000000] .init : 0xc0623000 - 0xc0657e4c ( 212 kB)
[ 0.000000] .data : 0xc0658000 - 0xc06ae824 ( 347 kB)
[ 0.000000] .bss : 0xc06ae824 - 0xc0718d6c ( 426 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:114
[ 0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474836475ns
[ 0.000000] Console: colour dummy device 80x30
[ 13.456558] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[ 13.546342] pid_max: default: 32768 minimum: 301
[ 13.546446] Security Framework initialized
[ 13.546521] Mount-cache hash table entries: 512
[ 13.547149] Initializing cgroup subsys devices
[ 13.547175] Initializing cgroup subsys freezer
[ 13.547188] Initializing cgroup subsys net_cls
[ 13.547199] Initializing cgroup subsys blkio
[ 13.547286] CPU: Testing write buffer coherency: ok
[ 13.547680] Setting up static identity map for 0x469248 - 0x469284
[ 13.549815] devtmpfs: initialized
[ 13.552240] prandom: seed boundary self test passed
[ 13.556258] prandom: 100 self tests passed
[ 13.556269] pinctrl core: initialized pinctrl subsystem
[ 13.556673] regulator-dummy: no parameters
[ 13.557008] NET: Registered protocol family 16
[ 13.557442] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 13.558055] cpuidle: using governor ladder
[ 13.558074] cpuidle: using governor menu
[ 13.558189] Kirkwood: MV88F6281-A0, TCLK=200000000.
[ 13.558210] Feroceon L2: Enabling L2
[ 13.558249] Feroceon L2: Cache support initialised.
[ 13.562240] bio: create slab <bio-0> at 0
[ 13.562680] vgaarb: loaded
[ 13.562895] usbcore: registered new interface driver usbfs
[ 13.562955] usbcore: registered new interface driver hub
[ 13.563059] usbcore: registered new device driver usb
[ 13.563669] Switched to clocksource orion_clocksource
[ 13.584167] NET: Registered protocol family 2
[ 13.584826] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 13.584863] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 13.584894] TCP: Hash tables configured (established 2048 bind 2048)
[ 13.584963] TCP: reno registered
[ 13.584976] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 13.584998] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 13.585200] NET: Registered protocol family 1
[ 13.585523] RPC: Registered named UNIX socket transport module.
[ 13.585534] RPC: Registered udp transport module.
[ 13.585541] RPC: Registered tcp transport module.
[ 13.585549] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 13.585795] Unpacking initramfs...
[ 14.129664] Freeing initrd memory: 6408K (c1101000 - c1743000)
[ 14.129777] NetWinder Floating Point Emulator V0.97 (double precision)
[ 14.130373] audit: initializing netlink socket (disabled)
[ 14.130425] type=2000 audit(0.660:1): initialized
[ 14.131211] zbud: loaded
[ 14.131379] VFS: Disk quotas dquot_6.5.2
[ 14.131430] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 14.131810] NFS: Registering the id_resolver key type
[ 14.131868] Key type id_resolver registered
[ 14.131877] Key type id_legacy registered
[ 14.131896] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 14.131905] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 14.132074] jffs2: version 2.2. (NAND) (SUMMARY) آ© 2001-2006 Red Hat, Inc.
[ 14.132344] msgmni has been set to 493
[ 14.132468] Key type big_key registered
[ 14.134387] alg: No test for stdrng (krng)
[ 14.134480] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 14.134493] io scheduler noop registered
[ 14.134501] io scheduler deadline registered
[ 14.134524] io scheduler cfq registered (default)
[ 14.134728] mv_xor mv_xor.0: Marvell shared XOR driver
[ 14.173732] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 14.213733] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 14.213835] mv_xor mv_xor.1: Marvell shared XOR driver
[ 14.253734] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[ 14.293733] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[ 14.293994] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 14.314571] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 12500000) is a 16550A
[ 14.841832] console [ttyS0] enabled
[ 14.846394] Could not find valid ONFI parameter page; aborting
[ 14.852259] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit)
[ 14.860757] NAND device: 128MiB, SLC, page size: 2048, OOB size: 64
[ 14.867071] Scanning device for bad blocks
[ 14.978468] 4 cmdlinepart partitions found on MTD device orion_nand
[ 14.984780] Creating 4 MTD partitions on "orion_nand":
[ 14.989948] 0x000000000000-0x000000100000 : "u-boot"
[ 14.995182] 0x000000100000-0x000000500000 : "uImage"
[ 15.000372] 0x000000500000-0x000002500000 : "rootfs"
[ 15.005635] 0x000002500000-0x000008000000 : "data"
[ 15.011239] libphy: Fixed MDIO Bus: probed
[ 15.027100] libphy: orion_mdio_bus: probed
[ 15.031313] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 16.039106] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:04:a2:18
[ 16.048017] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 16.054597] ehci-pci: EHCI PCI platform driver
[ 16.059105] ehci-orion: EHCI orion driver
[ 16.063187] orion-ehci orion-ehci.0: EHCI Host Controller
[ 16.068648] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 16.076395] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 16.093708] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 16.099827] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 16.106668] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 16.113942] usb usb1: Product: EHCI Host Controller
[ 16.118845] usb usb1: Manufacturer: Linux 3.13.1-kirkwood-tld-2 ehci_hcd
[ 16.125592] usb usb1: SerialNumber: orion-ehci.0
[ 16.130691] hub 1-0:1.0: USB hub found
[ 16.134529] hub 1-0:1.0: 1 port detected
[ 16.138938] mousedev: PS/2 mouse device common for all mice
[ 16.453725] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 16.605146] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[ 16.611894] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 16.619087] usb 1-1: Product: USB2.0 Hub
[ 16.623634] hub 1-1:1.0: USB hub found
[ 16.627769] hub 1-1:1.0: 4 ports detected
[ 16.914023] usb 1-1.4: new high-speed USB device number 3 using orion-ehci
[ 17.030893] usb 1-1.4: New USB device found, idVendor=058f, idProduct=6387
[ 17.037846] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 17.045236] usb 1-1.4: Product: Mass Storage
[ 17.049549] usb 1-1.4: SerialNumber: 819B6C75
[ 17.153695] rtc-mv rtc-mv: internal RTC not ticking
[ 17.158694] i2c /dev entries driver
[ 17.162697] drop_monitor: Initializing network drop monitor service
[ 17.169201] TCP: cubic registered
[ 17.172535] NET: Registered protocol family 17
[ 17.177119] Key type dns_resolver registered
[ 17.181857] registered taskstats version 1
[ 17.186767] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 17.193986] Freeing unused kernel memory: 208K (c0623000 - c0657000)
Loading, please wait...
[ 17.264391] udevd[54]: starting version 175
[ 17.418904] SCSI subsystem initialized
[ 17.457221] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[ 17.498898] scsi0 : usb-storage 1-1.4:1.0
[ 17.514364] usbcore: registered new interface driver usb-storage
[ 18.495755] scsi 0:0:0:0: Direct-Access USB Disk 8.07 PQ: 0 ANSI: 4
[ 18.532712] sd 0:0:0:0: [sda] 7864320 512-byte logical blocks: (4.02 GB/3.75 GiB)
[ 18.541310] sd 0:0:0:0: [sda] Write Protect is off
[ 18.547180] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 18.576299] sda: sda1
[ 18.582430] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 18.598281] sd 0:0:0:0: Attached scsi generic sg0 type 0
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
[ 27.660322] EXT3-fs (sda1): mounted filesystem with ordered data mode
[ 27.666893] kjournald starting. Commit interval 5 seconds
Begin: Running /scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... done.
Target filesystem doesn't have requested /sbin/init.
No init found. Try passing init= bootarg.
modprobe: module i8042 not found in modules.dep
[ 27.755323] uhci_hcd: USB Universal Host Controller Interface driver
[ 27.768452] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 27.784310] hidraw: raw HID events driver (C) Jiri Kosina
[ 27.791839] usbcore: registered new interface driver usbhid
[ 27.797602] usbhid: USB HID core driver
BusyBox v1.20.2 (Debian 1:1.20.0-7) built-in shell (ash)
Enter 'help' for a list of built-in commands.
/bin/sh: can't access tty; job control turned off
(initramfs)
(initramfs)
(initramfs)
(initramfs)
(initramfs)
(initramfs)
(initramfs)
(initramfs)
(initramfs)
Then what ??
|
Re: PogoPlug E02 Black March 04, 2014 04:44PM |
Admin Registered: 13 years ago Posts: 18,580 |
Did you extract the rootfs archive as root user?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: PogoPlug E02 Black March 04, 2014 04:49PM |
Registered: 10 years ago Posts: 37 |
|
Re: PogoPlug E02 Black March 04, 2014 05:03PM |
Admin Registered: 13 years ago Posts: 18,580 |
msanad Wrote:
-------------------------------------------------------
> i'm using Windows 7 so i use some software to
> format the USB flash memory and extract the Zip
> file to it as administrator user.
>
> is this enough ??
Afraid not! Must be root user on Linux. You can do this using Linux Live Cd if there is no other Linux box available.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> i'm using Windows 7 so i use some software to
> format the USB flash memory and extract the Zip
> file to it as administrator user.
>
> is this enough ??
Afraid not! Must be root user on Linux. You can do this using Linux Live Cd if there is no other Linux box available.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: PogoPlug E02 Black March 04, 2014 05:09PM |
Registered: 10 years ago Posts: 37 |
|
Re: PogoPlug E02 Black March 04, 2014 05:13PM |
Registered: 10 years ago Posts: 37 |
|
Re: PogoPlug E02 Black March 05, 2014 04:49PM |
Registered: 10 years ago Posts: 37 |
I'm following these steps
but dont understand this point , what do you mean by the following :
Download at Dropbox: Debian-3.13.1-kirkwood-tld-2-rootfs-bodhi.tar.bz2 md5: 7e41aa117a9cea341f007bc6a53ad6a8 Installation: - format a new ext3 USB drive, and label it rootfs. Note: if your uBoot env for usb_rootfstype is ext2, then use an ext2 USB drive. - As root user, cd to top level directory and extract it (assuming the USB drive is mounted at /media/sdb1) cd /media/sdb1 tar -xjf Debian-3.13.1-kirkwood-tld-2-rootfs-bodhi.tar.bz2
but dont understand this point , what do you mean by the following :
- edit /media/sdb1/etc/fstab entry for /dev/root to match the rootfstype of your usb_rootfstype. sync - reboot
|
Re: PogoPlug E02 Black March 05, 2014 05:20PM |
Registered: 10 years ago Posts: 37 |
Now i logged to root@debian:~# , So what is next
Here is the log
Here is the log
U-Boot 2013.10 (Feb 21 2014 - 19:35:02)-tld-2
Pogo E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
Hit any key to stop autoboot: 0
PogoE02>
PogoE02>
PogoE02>
PogoE02>
PogoE02>
PogoE02>
PogoE02> setenv console 'ttyS0,115200'
PogoE02> setenv usb_device '0:1'
PogoE02> setenv mtdparts 'mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)'
PogoE02> setenv usb_set_bootargs 'setenv bootargs console=$console root=/dev/sda1 rootdelay=10 rootfstype=ext3 $mtdparts'
PogoE02> setenv usb_boot 'mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi'
PogoE02> setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot'
PogoE02> setenv bootcmd 'usb start; run usb_bootcmd; usb stop; reset'
PogoE02> boot
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
2399792 bytes read in 353 ms (6.5 MiB/s)
6568066 bytes read in 579 ms (10.8 MiB/s)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-3.13.1-kirkwood-tld-2
Created: 2014-02-05 19:30:49 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2399728 Bytes = 2.3 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-3.13.1-kirkwood-tld-2
Created: 2014-02-05 19:31:01 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 6568002 Bytes = 6.3 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.13.1-kirkwood-tld-2 (root@tldDebian) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 PREEMPT Tue Feb 4 03:19:07 PST 2014
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Pogoplug E02
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext3 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 246168K/262144K available (4659K kernel code, 346K rwdata, 1588K rodata, 211K init, 425K bss, 15976K reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06220ac (6249 kB)
[ 0.000000] .init : 0xc0623000 - 0xc0657e4c ( 212 kB)
[ 0.000000] .data : 0xc0658000 - 0xc06ae824 ( 347 kB)
[ 0.000000] .bss : 0xc06ae824 - 0xc0718d6c ( 426 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:114
[ 0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474836475ns
[ 0.000000] Console: colour dummy device 80x30
[ 7.587040] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[ 7.676826] pid_max: default: 32768 minimum: 301
[ 7.676931] Security Framework initialized
[ 7.677007] Mount-cache hash table entries: 512
[ 7.677639] Initializing cgroup subsys devices
[ 7.677665] Initializing cgroup subsys freezer
[ 7.677680] Initializing cgroup subsys net_cls
[ 7.677691] Initializing cgroup subsys blkio
[ 7.677779] CPU: Testing write buffer coherency: ok
[ 7.678172] Setting up static identity map for 0x469248 - 0x469284
[ 7.680307] devtmpfs: initialized
[ 7.682748] prandom: seed boundary self test passed
[ 7.686767] prandom: 100 self tests passed
[ 7.686863] pinctrl core: initialized pinctrl subsystem
[ 7.687199] regulator-dummy: no parameters
[ 7.687534] NET: Registered protocol family 16
[ 7.687970] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 7.688585] cpuidle: using governor ladder
[ 7.688604] cpuidle: using governor menu
[ 7.688719] Kirkwood: MV88F6281-A0, TCLK=200000000.
[ 7.688740] Feroceon L2: Enabling L2
[ 7.688780] Feroceon L2: Cache support initialised.
[ 7.692766] bio: create slab <bio-0> at 0
[ 7.693206] vgaarb: loaded
[ 7.693422] usbcore: registered new interface driver usbfs
[ 7.693481] usbcore: registered new interface driver hub
[ 7.693584] usbcore: registered new device driver usb
[ 7.694193] Switched to clocksource orion_clocksource
[ 7.714639] NET: Registered protocol family 2
[ 7.715300] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 7.715337] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 7.715367] TCP: Hash tables configured (established 2048 bind 2048)
[ 7.715436] TCP: reno registered
[ 7.715449] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 7.715471] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 7.715673] NET: Registered protocol family 1
[ 7.715998] RPC: Registered named UNIX socket transport module.
[ 7.716009] RPC: Registered udp transport module.
[ 7.716017] RPC: Registered tcp transport module.
[ 7.716024] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 7.716270] Unpacking initramfs...
[ 8.260115] Freeing initrd memory: 6408K (c1101000 - c1743000)
[ 8.260229] NetWinder Floating Point Emulator V0.97 (double precision)
[ 8.260824] audit: initializing netlink socket (disabled)
[ 8.260875] type=2000 audit(0.660:1): initialized
[ 8.261661] zbud: loaded
[ 8.261832] VFS: Disk quotas dquot_6.5.2
[ 8.261883] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 8.262263] NFS: Registering the id_resolver key type
[ 8.262329] Key type id_resolver registered
[ 8.262338] Key type id_legacy registered
[ 8.262357] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 8.262366] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 8.262533] jffs2: version 2.2. (NAND) (SUMMARY) آ© 2001-2006 Red Hat, Inc.
[ 8.262804] msgmni has been set to 493
[ 8.262929] Key type big_key registered
[ 8.264841] alg: No test for stdrng (krng)
[ 8.264936] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 8.264948] io scheduler noop registered
[ 8.264956] io scheduler deadline registered
[ 8.264980] io scheduler cfq registered (default)
[ 8.265184] mv_xor mv_xor.0: Marvell shared XOR driver
[ 8.304256] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 8.344257] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 8.344357] mv_xor mv_xor.1: Marvell shared XOR driver
[ 8.384257] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[ 8.424255] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[ 8.424516] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 8.445092] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 12500000) is a 16550A
[ 8.972303] console [ttyS0] enabled
[ 8.976862] Could not find valid ONFI parameter page; aborting
[ 8.982730] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit)
[ 8.991227] NAND device: 128MiB, SLC, page size: 2048, OOB size: 64
[ 8.997543] Scanning device for bad blocks
[ 9.108913] 4 cmdlinepart partitions found on MTD device orion_nand
[ 9.115224] Creating 4 MTD partitions on "orion_nand":
[ 9.120385] 0x000000000000-0x000000100000 : "u-boot"
[ 9.125617] 0x000000100000-0x000000500000 : "uImage"
[ 9.130811] 0x000000500000-0x000002500000 : "rootfs"
[ 9.136074] 0x000002500000-0x000008000000 : "data"
[ 9.141682] libphy: Fixed MDIO Bus: probed
[ 9.157607] libphy: orion_mdio_bus: probed
[ 9.161820] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 10.169615] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:04:a2:18
[ 10.178522] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 10.185103] ehci-pci: EHCI PCI platform driver
[ 10.189612] ehci-orion: EHCI orion driver
[ 10.193695] orion-ehci orion-ehci.0: EHCI Host Controller
[ 10.199155] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 10.206900] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 10.224229] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 10.230348] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 10.237192] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 10.244467] usb usb1: Product: EHCI Host Controller
[ 10.249368] usb usb1: Manufacturer: Linux 3.13.1-kirkwood-tld-2 ehci_hcd
[ 10.256116] usb usb1: SerialNumber: orion-ehci.0
[ 10.261218] hub 1-0:1.0: USB hub found
[ 10.265054] hub 1-0:1.0: 1 port detected
[ 10.269462] mousedev: PS/2 mouse device common for all mice
[ 10.584248] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 10.735654] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[ 10.742401] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 10.749593] usb 1-1: Product: USB2.0 Hub
[ 10.754142] hub 1-1:1.0: USB hub found
[ 10.758277] hub 1-1:1.0: 4 ports detected
[ 11.044530] usb 1-1.4: new high-speed USB device number 3 using orion-ehci
[ 11.161401] usb 1-1.4: New USB device found, idVendor=058f, idProduct=6387
[ 11.168351] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 11.175741] usb 1-1.4: Product: Mass Storage
[ 11.180047] usb 1-1.4: SerialNumber: 819B6C75
[ 11.284219] rtc-mv rtc-mv: internal RTC not ticking
[ 11.289217] i2c /dev entries driver
[ 11.293227] drop_monitor: Initializing network drop monitor service
[ 11.299734] TCP: cubic registered
[ 11.303067] NET: Registered protocol family 17
[ 11.307654] Key type dns_resolver registered
[ 11.312385] registered taskstats version 1
[ 11.317337] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 11.324551] Freeing unused kernel memory: 208K (c0623000 - c0657000)
Loading, please wait...
[ 11.394893] udevd[54]: starting version 175
[ 11.550849] SCSI subsystem initialized
[ 11.594063] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[ 11.631388] scsi0 : usb-storage 1-1.4:1.0
[ 11.644616] usbcore: registered new interface driver usb-storage
[ 12.646262] scsi 0:0:0:0: Direct-Access USB Disk 8.07 PQ: 0 ANSI: 4
[ 12.683091] sd 0:0:0:0: [sda] 7864320 512-byte logical blocks: (4.02 GB/3.75 GiB)
[ 12.691817] sd 0:0:0:0: [sda] Write Protect is off
[ 12.697694] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 12.726806] sda: sda1
[ 12.732934] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 12.748742] sd 0:0:0:0: Attached scsi generic sg0 type 0
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
[ 21.787494] EXT3-fs (sda1): recovery required on readonly filesystem
[ 21.793897] EXT3-fs (sda1): write access will be enabled during recovery
[ 32.537299] kjournald starting. Commit interval 5 seconds
[ 33.726567] EXT3-fs (sda1): recovery complete
[ 33.730950] EXT3-fs (sda1): mounted filesystem with ordered data mode
Begin: Running /scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: udevd[ 35.175226] udevd[227]: starting version 175
. ok
[....] Synthesizing the initial hotplug events...done.
[....] Waiting for /dev to be fully populated...[ 35.628255] alg: hash: Test 1 failed for mv-hmac-sha1
[ 35.633360] 00000000: 0c aa 9f d5 37 c3 79 3a 91 d9 21 5f 42 2b 2c 24
[ 35.649739] 00000010: b7 c3 16 0c
[ 35.659359] orion_wdt: Initial timeout 21 sec
[ 35.826333] random: nonblocking pool is initialized
done.
[....] Activating swap...done.
[....] Checking root file system...fsck from util-linux 2.20.1
New_Volume: clean, 17118/245760 files, 137137/982134 blocks
done.
[ 38.176136] EXT3-fs (sda1): using internal journal
[....] Loading kernel modules...done.
[....] Cleaning up temporary files... /lib/init/rw. ok
[....] Activating lvm and md swap...done.
[....] Checking file systems...fsck from util-linux 2.20.1
done.
[....] Mounting local filesystems...done.
[....] Activating swapfile swap...done.
[....] Cleaning up temporary files.... ok
[....] Setting kernel variables ...done.
[....] Configuring network interfaces...[ 42.280451] NET: Registered protocol family 10
Internet Systems Consortium DHCP Client 4.2.2
Copyright 2004-2011 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
[ 42.474878] mv643xx_eth_port mv643xx_eth_port.0 eth0: link down
[ 42.480971] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Listening on LPF/eth0/00:25:31:04:a2:18
Sending on LPF/eth0/00:25:31:04:a2:18
Sending on Socket/fallback
DHCPREQUEST on eth0 to 255.255.255.255 port 67
[ 44.129319] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, full duplex, flow control disabled
[ 44.139157] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPACK from 192.168.1.1
bound to 192.168.1.3 -- renewal in 35704 seconds.
done.
[....] Starting rpcbind daemon.... ok
[....] Starting NFS common utilities: statd idmapd. ok
[....] Cleaning up temporary files.... ok
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1652 (syslogd)
. ok
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1651 (klogd)
. ok
[....] Starting system message bus: dbus. ok
[....] Starting NFS common utilities: statd idmapd. ok
[....] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. ok
[....] Starting NTP server: ntpd. ok
[....] Starting rpcbind daemon...[....] Already running.. ok
[....] Not starting NFS kernel daemon: no exports. ... (warning).
[....] Starting OpenBSD Secure Shell server: sshd. ok
Debian GNU/Linux 7 debian ttyS0
debian login: root
roPassword:
Login incorrect
debian login: root
Password:
Last login: Wed Mar 5 15:13:52 PST 2014 on ttyS0
Linux debian 3.13.1-kirkwood-tld-2 #1 PREEMPT Tue Feb 4 03:19:07 PST 2014 armv5tel
The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
root@debian:~#
root@debian:~#
root@debian:~#
root@debian:~#
|
Re: PogoPlug E02 Black March 05, 2014 05:55PM |
Admin Registered: 13 years ago Posts: 18,580 |
Congrats! you're all set. Enjoy playing with your Pogo E02… remember to change your root password, and generate new SSH key.
Don't worry about this step, it is just a precaution.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 03/05/2014 05:58PM by bodhi.
Don't worry about this step, it is just a precaution.
- edit /media/sdb1/etc/fstab entry for /dev/root to match the rootfstype of your usb_rootfstype.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 03/05/2014 05:58PM by bodhi.
