Welcome! Log In Create A New Profile

Advanced

Pogoplug Series 4 V4-A03-01 PreInternet new uboot + dumb dumb = Kernel Panic

Posted by Jake 
Forum List Message List New Topic
Jake
Pogoplug Series 4 V4-A03-01 PreInternet new uboot + dumb dumb = Kernel Panic
January 23, 2021 08:09PM
Hello,
I picked up a new old stock Pogoplug Series 4 (V4-A03-01) recently after coming across this hackaday article.
I then watched the youtube uploads from Films by Kris.
This then lead me to Kris's "show notes" he posted on paste bin.
Hopefully adding the links and keywords will help others find this.

These are the commands I tried while following Kris's example (copied from pastebin):
Quote

#connect
screen /dev/ttyUSB0 115200,cs8,-parenb,-cstopb,-hupcl
#list partition
cat /proc/partitions
cat /proc/mtd
#remount / (root) as read/write
mount -o remount,rw /
#change root password
passwd root
#start telnetd or ssh server (both are already there)
#startup script can be found here
#(might want to enable dropbear and telnet and disable pogo services 'hbmgr.sh'):
vi /etc/init.d/rcS
#mount sdcard
mkdir /mnt/sdcard
mknod /dev/mmcblk0 b 179 0
mknod /dev/mmcblk0p1 b 179 1
mount /dev/mmcblk0p1 /mnt/sdcard
#mount USB drive
mkdir /mnt/usb
mknod /dev/sda b 8 0
mknod /dev/sda1 b 8 1
mount /dev/sda1 /mnt/usb
#add these lines to /etc/fstab
/dev/sda1 /mnt/usb vfat defaults 0 0
/dev/mmcblk0p1 /mnt/sdcard vfat defaults 0 0
The busybox install looked straight forward. I used an USB drive to transfer the busybox binary and everything seemed to be working. With the new busybox binary mounted to /tmp, I tested several new commands and everything seemed to work. So I copied /bin/busybox to a USB drive, and replaced the original binary with the new one. Kris lists the command he used to link everything on PB:
Quote

busybox --list|while read c;do echo $c;ln -s /bin/busybox $c;done
This is where things went south for me. I got a bunch of warnings about each command with a message (IIRC) calling something about each one illegal. This ended with an infinitely repeating "#" prompt. I let it sit for a few hours, but nothing changed and not knowing what else to do, I rebooted, then got kernel panic (my bootlog is attached to this post along with results of several other uboot commands and the kwboot versions too).

Questions:
Why does does my original Pogoplug printenv look so much different than the others I've seen posted here?
The lines with tabs seem to be unusual:
Quote

baudrate=115200
----bootargs=console=ttyS0,115200 root=ubi0:rootfs ubi.mtd=4,2048 rootfstype=ubifs
----boot=bootm 0x800000
bootcmd=run boot_nand
bootdelay=1
----boot_nand=run load_nand boot || run load_nand2 boot
----CASset=min
----ceboardver=PPV4A3
----disaMvPnp=no
----disL2Cache=no
----disL2Prefetch=yes
----enaCpuStream=no
----enaDCPref=yes
----enaICPref=yes
----enaMonExt=no
----enaWrAllo=no
----Environment size: 801/131068 bytes
ethact=egiga0
----ethaddr=00:50:43:00:02:02
----ethmtu=1500
----ethprime=egiga0
----hddPowerCtrl=no
ipaddr=169.254.254.253
----load_nand2=nboot 0x800000 0 0x500000
----load_nand=nboot 0x800000 0 0x200000
----loads_echo=0
mainlineLinux=no
----MALLOC_len=1
----nandEcc=1bit
----netbsd_en=no
----netmask=255.255.0.0
----pcieTune=no
----pexMode=RC
----rootpath=/mnt/ARM_FS/
----run_diag=yes
----sata_dma_mode=yes
serverip=169.254.254.254
----setL2CacheWT=yes
stderr=serial
stdin=serial
stdout=serial
----usb0Mode=host
----vxworks_en=no

I thought I would check in and see what the more experienced people here thought I should do next. This device has never had ethernet connected. Is there a copy of the complete stock pre-internet connected image somewhere already?
Is it possible to recover the original OS at this point? Do I dump the NAND with the original memory display command in uboot, decompress it somehow and try to modify it, or is there some other way to recover?
Thanks for taking the time to read this.
-Jake


Restating questions for easier unpacking:
1. Why does does my original Pogoplug printenv look so much different than the others I've seen posted here?
2. Is there a copy of this stock pre-internet-connected image somewhere already?
3. Is it possible to recover the original OS at this point?
4. Do I dump the NAND with the original memory display command in uboot, decompress it somehow and try to modify it, or is there some other way to recover?
+5. What other questions should I be asking in order to learn more about embedded Linux and apply this experience to other devices?



Edited 2 time(s). Last edit at 01/23/2021 09:10PM by Jake.
Reply Quote
Attachments:
open | download - uboot-orig-and-kwboot-cli-info (29.1 KB)
bodhi
Re: Pogoplug Series 4 V4-A03-01 PreInternet new uboot + dumb dumb = Kernel Panic
January 23, 2021 11:00PM
Jake,

Forget all about what you've read about this device.


See these 2 posts:

Debian:

https://forum.doozan.com/read.php?2,12096

U-Boot:

https://forum.doozan.com/read.php?3,12381

Basically, you can intall new u-boot and Debian rootfs (i.e. latest Linux kernel) from inside stock OS (in one session). Stock FW will be no longer relevant after that.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Reply Quote
Jake
Re: Pogoplug Series 4 V4-A03-01 PreInternet new uboot + dumb dumb = Kernel Panic
January 23, 2021 11:51PM
Thanks for the reply Mr Bodhi :-)
I can't log into the original OS though. I only have access to the original uboot cli (then kernel panic b4 user space loads.

Quote

U-Boot 1.1.4 (Oct 1 2011 - 12:06:06) Cloud Engines 1.1.2 (3.4.27) PHYADDR=0

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006918B4

Soc: 88F6192 A1 (DDR2)
CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 200Mhz , TClock = 166Mhz

DRAM CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB
*** Warning - bad CRC or NAND, using default environment

Flash: 0 kB

CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD (GUESSED): PPV4A3

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0

Loading from NAND 128MB 3,3V 8-bit, offset 0x200000
Image Name: Linux-2.6.31.8
Created: 2011-09-28 19:09:20 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2080956 Bytes = 2 MB
Load Address: 00008000
Entry Point: 00008000
## Booting image at 00800000 ...
Image Name: Linux-2.6.31.8
Created: 2011-09-28 19:09:20 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2080956 Bytes = 2 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux..................................................................................
................................................... done, booting the kernel.
[ 0.000000] Linux version 2.6.31.8 (afenn@kt) (gcc version 4.3.2 (sdk3.3-ct-ng-1.4.1) ) #5 Wed Sep 28 12:09:12 PDT 2011
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Feroceon-KW
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Ignoring unrecognised tag 0x41004345
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=ubi0:rootfs ubi.mtd=4,2048 rootfstype=ubifs
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 128MB = 128MB total
[ 0.000000] Memory: 118356KB available (3852K code, 261K data, 124K init, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Calibrating delay loop... 799.53 BogoMIPS (lpj=3997696)
[ 0.230000] Mount-cache hash table entries: 512
[ 0.230000] CPU: Testing write buffer coherency: ok
[ 0.230000] NET: Registered protocol family 16
[ 0.230000] Feroceon L2: Enabling L2
[ 0.230000] Feroceon L2: Cache support initialised.
[ 0.230000]
[ 0.230000] CPU Interface
[ 0.230000] -------------
[ 0.230000] SDRAM_CS0 ....base 00000000, size 128MB
[ 0.230000] SDRAM_CS1 ....disable
[ 0.230000] SDRAM_CS2 ....disable
[ 0.230000] SDRAM_CS3 ....disable
[ 0.230000] PEX0_MEM ....base e0000000, size 128MB
[ 0.230000] PEX0_IO ....base f2000000, size 1MB
[ 0.230000] PEX1_MEM ....no such
[ 0.230000] PEX1_IO ....no such
[ 0.230000] INTER_REGS ....base f1000000, size 1MB
[ 0.230000] NFLASH_CS ....base fa000000, size 2MB
[ 0.230000] SPI_CS ....base f4000000, size 16MB
[ 0.230000] BOOT_ROM_CS ....no such
[ 0.230000] DEV_BOOTCS ....no such
[ 0.230000] CRYPT_ENG ....base f0000000, size 2MB
[ 0.230000]
[ 0.230000] Marvell Development Board (LSP Version KW_LSP_5.1.3_patch18)-- RD-88F6192A-NAS Soc: 88F6192 A1 LE
[ 0.230000]
[ 0.230000] Detected Tclk 166666667 and SysClk 200000000
[ 0.230000] Marvell USB EHCI Host controller #0: c403e740
[ 0.730000] PEX0 interface detected Link X1
[ 0.740000] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 0.740000] pci 0000:00:01.0: PME# disabled
[ 0.740000] PCI: bus0: Fast back to back transfers disabled
[ 0.740000] mvPexLocalBusNumSet: ERR. Invalid PEX interface 1
[ 0.750000] bio: create slab <bio-0> at 0
[ 0.750000] SCSI subsystem initialized
[ 0.750000] usbcore: registered new interface driver usbfs
[ 0.750000] usbcore: registered new interface driver hub
[ 0.750000] usbcore: registered new device driver usb
[ 0.750000] NET: Registered protocol family 2
[ 0.750000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.750000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.750000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.750000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.750000] TCP reno registered
[ 0.750000] NET: Registered protocol family 1
[ 0.750000] cpufreq: Init kirkwood cpufreq driver
[ 0.760000] XOR registered 4 channels
[ 0.760000] XOR 2nd invalidate WA enabled
[ 0.760000] cesadev_init(c000d7fc)
[ 0.760000] mvCesaInit: sessions=640, queue=64, pSram=f0000000
[ 0.760000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.770000] msgmni has been set to 231
[ 0.770000] alg: No test for cipher_null (cipher_null-generic)
[ 0.770000] alg: No test for ecb(cipher_null) (ecb-cipher_null)
[ 0.770000] alg: No test for digest_null (digest_null-generic)
[ 0.770000] alg: No test for compress_null (compress_null-generic)
[ 0.780000] alg: No test for stdrng (krng)
[ 0.780000] alg: No test for hmac(digest_null) (hmac(digest_null-generic))
[ 0.790000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.790000] io scheduler noop registered
[ 0.790000] io scheduler anticipatory registered (default)
[ 0.790000] Initializing ths8200_init
[ 0.790000] Initializing dove_adi9889_init
[ 0.810000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.810000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 0.810000] console [ttyS0] enabled
[ 0.820000] Integrated Sata device found
[ 0.830000] IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
[ 0.850000] scsi0 : Marvell SCSI to SATA adapter
[ 0.860000] scsi1 : Marvell SCSI to SATA adapter
[ 0.870000] Loading Marvell Ethernet Driver:
[ 0.870000] o Cached descriptors in DRAM
[ 0.880000] o DRAM SW cache-coherency
[ 0.880000] o 1 Giga ports supported
[ 0.880000] o Single RX Queue support - ETH_DEF_RXQ=0
[ 0.890000] o Single TX Queue support - ETH_DEF_TXQ=0
[ 0.890000] o TCP segmentation offload (TSO) supported
[ 0.900000] o Large Receive offload (LRO) supported
[ 0.900000] o Receive checksum offload supported
[ 0.910000] o Transmit checksum offload supported
[ 0.910000] o Network Fast Processing (Routing) supported - (Disabled)
[ 0.920000] o Driver ERROR statistics enabled
[ 0.930000] o Proc tool API enabled
[ 0.930000] o SKB Reuse supported - (Disabled)
[ 0.930000] o SKB Recycle supported - (Disabled)
[ 0.940000] o Rx descripors: q0=128
[ 0.940000] o Tx descripors: q0=532
[ 0.950000] o Loading network interface(s):
[ 0.950000] o register under mv88fx_eth platform
[ 0.960000] o eth0, ifindex = 2, GbE port = 0
[ 0.960000]
[ 0.960000] mvFpRuleDb (c45b1000): 1024 entries, 4096 bytes
[ 0.970000] Counter=0, opIdx=6, overhead=16
[ 0.970000] Counter=1, opIdx=2, overhead=0
[ 0.980000] Counter=2, opIdx=1, overhead=18
[ 0.980000] Counter=3, opIdx=2, overhead=0
[ 0.990000] tun: Universal TUN/TAP device driver, 1.6
[ 0.990000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 1.000000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit)
[ 1.010000] Scanning device for bad blocks
[ 1.020000] Bad eraseblock 240 at 0x000001e00000
[ 1.060000] Using static partition definition
[ 1.070000] Creating 5 MTD partitions on "nand_mtd":
[ 1.070000] 0x000000000000-0x000000200000 : "u-boot"
[ 1.080000] 0x000000200000-0x000000500000 : "uImage"
[ 1.080000] 0x000000500000-0x000000800000 : "uImage2"
[ 1.090000] 0x000000800000-0x000001000000 : "failsafe"
[ 1.090000] 0x000001000000-0x000008000000 : "root"
[ 1.100000] UBI: attaching mtd4 to ubi0
[ 1.100000] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 1.110000] UBI: logical eraseblock size: 126976 bytes
[ 1.120000] UBI: smallest flash I/O unit: 2048
[ 1.120000] UBI: sub-page size: 512
[ 1.120000] UBI: VID header offset: 2048 (aligned 2048)
[ 1.130000] UBI: data offset: 4096
[ 1.360000] UBI: attached mtd4 to ubi0
[ 1.360000] UBI: MTD device name: "root"
[ 1.360000] UBI: MTD device size: 112 MiB
[ 1.370000] UBI: number of good PEBs: 895
[ 1.370000] UBI: number of bad PEBs: 1
[ 1.380000] UBI: max. allowed volumes: 128
[ 1.380000] UBI: wear-leveling threshold: 4096
[ 1.390000] UBI: number of internal volumes: 1
[ 1.390000] UBI: number of user volumes: 1
[ 1.400000] UBI: available PEBs: 0
[ 1.400000] UBI: total number of reserved PEBs: 895
[ 1.410000] UBI: number of PEBs reserved for bad PEB handling: 8
[ 1.410000] UBI: max/mean erase counter: 1/0
[ 1.420000] UBI: image sequence number: 0
[ 1.420000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.430000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
[ 1.430000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
[ 1.440000] UBI: background thread "ubi_bgt0d" started, PID 452
[ 1.470000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
[ 1.490000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
[ 1.490000] usb usb1: configuration #1 chosen from 1 choice
[ 1.500000] hub 1-0:1.0: USB hub found
[ 1.500000] hub 1-0:1.0: 1 port detected
[ 1.510000] xhci_hcd 0000:00:01.0: xHCI Host Controller
[ 1.510000] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 2
[ 1.520000] xhci_hcd 0000:00:01.0: irq 9, io mem 0xe0000000
[ 1.530000] usb usb2: config 1 interface 0 altsetting 0 endpoint 0x81 has no SuperSpeed companion descriptor
[ 1.540000] usb usb2: configuration #1 chosen from 1 choice
[ 1.540000] hub 2-0:1.0: USB hub found
[ 1.550000] hub 2-0:1.0: 4 ports detected
[ 1.550000] Initializing USB Mass Storage driver...
[ 1.550000] usbcore: registered new interface driver usb-storage
[ 1.560000] USB Mass Storage support registered.
[ 1.570000] usbcore: registered new interface driver ums-datafab
[ 1.570000] usbcore: registered new interface driver ums-freecom
[ 1.580000] usbcore: registered new interface driver ums-jumpshot
[ 1.580000] usbcore: registered new interface driver ums-sddr09
[ 1.590000] usbcore: registered new interface driver ums-sddr55
[ 1.600000] usbcore: registered new interface driver ums-usbat
[ 1.600000] mice: PS/2 mouse device common for all mice
[ 1.610000] i2c /dev entries driver
[ 1.620000] sdhci: Secure Digital Host Controller Interface driver
[ 1.620000] sdhci: Copyright(c) Pierre Ossman
[ 1.630000] mmc0: mvsdio driver initialized, using GPIO 27 for card detection
[ 1.640000] usbcore: registered new interface driver usbhid
[ 1.640000] usbhid: v2.6:USB HID core driver
[ 1.650000] TCP cubic registered
[ 1.650000] NET: Registered protocol family 17
[ 1.660000] RPC: Registered udp transport module.
[ 1.660000] RPC: Registered tcp transport module.
[ 1.670000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.740000] UBIFS: recovery needed
[ 1.840000] UBIFS: recovery completed
[ 1.840000] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 1.850000] UBIFS: file system size: 110723072 bytes (108128 KiB, 105 MiB, 872 LEBs)
[ 1.860000] UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
[ 1.860000] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 1.870000] UBIFS: default compressor: lzo
[ 1.870000] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 1.880000] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 1.890000] Freeing init memory: 124K
[ 2.950000] Kernel panic - not syncing: Attempted to kill init!
[ 2.950000] Backtrace:
[ 2.950000] [<c00fe1bc>] (dump_backtrace+0x0/0x114) from [<c0035594>] (dump_stack+0x18/0x1c)
[ 2.960000] r7:c401ff50 r6:c4019c40 r5:c4019c40 r4:c0415830
[ 2.970000] [<c003557c>] (dump_stack+0x0/0x1c) from [<c00355e4>] (panic+0x4c/0x114)
[ 2.980000] [<c0035598>] (panic+0x0/0x114) from [<c012dce8>] (do_exit+0x7c/0x5b4)
[ 2.980000] r3:c03f1d94 r2:c401fe40 r1:c401fd04 r0:c00c250b
[ 2.990000] [<c012dc6c>] (do_exit+0x0/0x5b4) from [<c012e2b4>] (do_group_exit+0x94/0xc8)
[ 3.000000] [<c012e220>] (do_group_exit+0x0/0xc8) from [<c0137d4c>] (get_signal_to_deliver+0x2e0/0x318)
[ 3.010000] r5:c401fed0 r4:00000004
[ 3.010000] [<c0137a6c>] (get_signal_to_deliver+0x0/0x318) from [<c00fca38>] (do_signal+0x5c/0x58c)
[ 3.020000] [<c00fc9dc>] (do_signal+0x0/0x58c) from [<c00fcf98>] (do_notify_resume+0x30/0x34)
[ 3.030000] [<c00fcf68>] (do_notify_resume+0x0/0x34) from [<c002c7cc>] (work_pending+0x1c/0x20)



Edited 1 time(s). Last edit at 01/23/2021 11:56PM by Jake.
Reply Quote
bodhi
Re: Pogoplug Series 4 V4-A03-01 PreInternet new uboot + dumb dumb = Kernel Panic
January 24, 2021 03:21PM
Jake,

Are you the same Jake here?

https://forum.doozan.com/read.php?3,7852,114859#msg-114859

You stock OS seems to be corrupted. So now you should use kwboot to boot the box into Debian on USB and then install new u-boot.

Basically, you can kwboot the box using the latest Pogo V4 u-boot image uboot.2017.07-tld-1.pogo_v4.mtd0.kwb

And then boot into the rootfs Debian-5.2.9-kirkwood-tld-1-rootfs-bodhi.tar.bz2. There is no need to change any u-boot env.


- Example of kwboot (ignore this if you already know how):
https://forum.doozan.com/read.php?3,51739,51919#msg-51919

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Reply Quote
Jake
Re: Pogoplug Series 4 V4-A03-01 PreInternet new uboot + dumb dumb = Kernel Panic
January 24, 2021 10:01PM
bodhi Wrote:

> Are you the same Jake?


Yup. The same indeed.
...I thought I was on the right path with kwboot. The oddity of my environment variables is the only reason I asked.
I had to order more USB drives though. It looks like kwboot doesn't like any of my sdcard adapters. It labels the initial partition type as DOS, and it spits out "EHCI timmed out on TD - token=..." with all variations I have tried. I used the Gnome Disk Utility and mke2fs to completely wipe the drives, including the boot table of a spare USB flash and several spare sdcards formatted as ext3, and ext4, but they all have the same result. The last log also has a spot that mentions ext4 on the file below. I don't recall what it said when I formatted ext3, but I do recall seeing the "Partition Type: DOS" message.
Quote

U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:34:01 -0700)
Pogoplug V4

SoC: Kirkwood 88F6192_A1
DRAM: 128 MiB
WARNING: Caches not enabled
NAND: 128 MiB
MMC: MVEBU_MMC: 0
*** Warning - bad CRC, using default environment

In: serial
Out: serial
Err: serial
Net: egiga0
Hit any key to stop autoboot: 0
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices...
Use USB retry period from the environment: 15 second(s)
1 Storage Device(s) found

Reset IDE: ide_preinit failed
Card did not respond to voltage select!
mmc_init: -95, time 14

Partition Map for USB device 0 -- Partition Type: DOS

Part Start Sector Num Sectors UUID Type
1 2048 15521792 00000000-01 0c Boot

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **

no IDE devices available
Card did not respond to voltage select!
mmc_init: -95, time 14
running scan_disk ...
Scan device usb
device usb 0:1
1 bytes read in 692 ms (0 Bytes/s)

Found bootable drive on usb 0
loading uImage ...
EHCI timed out on TD - token=0xb0008d80
EHCI timed out on TD - token=0xc4008988
EHCI timed out on TD - token=0x128d80
EHCI timed out on TD - token=0x40008d80
EHCI timed out on TD - token=0x128d80
EHCI timed out on TD - token=0x3e008d80
EHCI timed out on TD - token=0x128d80
EHCI timed out on TD - token=0x2e008d80
EHCI timed out on TD - token=0x128d80
EHCI timed out on TD - token=0x2e008d80
EHCI timed out on TD - token=0x128d80
EHCI timed out on TD - token=0x2e008d80
EHCI timed out on TD - token=0x128d80
EHCI timed out on TD - token=0x2e008d80
EHCI timed out on TD - token=0x128d80
** ext4fs_devread read error - block
loading uInitrd ...
EHCI timed out on TD - token=0x2008d80
EHCI timed out on TD - token=0x128d80
EHCI timed out on TD - token=0x2008d80
EHCI timed out on TD - token=0x128d80
EHCI timed out on TD - token=0x2008d80
EHCI timed out on TD - token=0x128d80
** Can't read partition table on 0:0 **
** Invalid partition 1 **
loading DTB /boot/dts/kirkwood-pogoplug_v4 ...
EHCI timed out on TD - token=0x2008d80
EHCI timed out on TD - token=0x128d80
EHCI timed out on TD - token=0x2008d80
EHCI timed out on TD - token=0x128d80
EHCI timed out on TD - token=0x2008d80
EHCI timed out on TD - token=0x128d80
** Can't read partition table on 0:0 **
** Invalid partition 1 **
Unknown command 'bootm0x800000' - try 'help'
resetting ...

I think the issue is my flash media, but I tried:
Debian-5.2.9-kirkwood-tld-1-rootfs-bodhi.tar.bz2
(w/ step 4 and wo/)
uboot.2017.07-tld-1.pogo_v4.mtd0.kwb
uboot.2014.07-tld-1.pogo_v4.mtd0.kwb

Probably the wrong place to ask, but do you have any advice on an easier path into JTAG with embedded Linux on these devices? I have a FT2232 breakout, and I've etched my own Goodfet42, but I have not figured out a way to work with SWD on these (something I've needed before). I haven't made a solid attempt at using them well either. I'm on Fedora SB (mostly)/Gentoo on this machine, and I just got urjtag to mess with.
Every time I've tried messing with JTAG I find myself in a Grand Canyon size rabbit hole. My last attempt involved trying to load a SAMD21 with the Arduino bootloader. By the time I emerged from that project I had a STM32 working with micropython and a desire to never touch a SAMD chip again :-)
-Jake
Reply Quote
bodhi
Re: Pogoplug Series 4 V4-A03-01 PreInternet new uboot + dumb dumb = Kernel Panic
January 25, 2021 03:41AM
Jake,


> scanning usb for storage devices...
> Use USB retry period from the environment: 15
> second(s)
> 1 Storage Device(s) found

So the USB was initialized by u-boot.

> Found bootable drive on usb 0
> loading uImage ...
> EHCI timed out on TD - token=0xb0008d80

> I think the issue is my flash media,

Yes.

> Probably the wrong place to ask, but do you have
> any advice on an easier path into JTAG with
> embedded Linux on these devices?

No need for JTAG. You won't get better result with JTAG, as you can boot with serial console.

The issue is the USB drive. Try using a SanDisk brand USB thumb drive. The error "EHCI timed out on TD" happens with some older USB controller on the drives. My experience is the SanDisk USB is best for booting.

Usually kwboot should work. But the worst case is you have to flash u-boot in serial console and then try to overcome that error. We'll come to that when all else failed.

Fo rnow, try slowing down the boot process this way:

- kwboot with uboot.2017.07-tld-1.pogo_v4.mtd0.kwb
- interrupt serial console
- Initialize the USB drive 

usb reset
and then wait 10 seconds 
run set_bootargs
run bootcmd_exec

See if by waiting long enough to let the USB to settle down, you can get it to load the kernel and run it.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Reply Quote
Jake
Re: Pogoplug Series 4 V4-A03-01 PreInternet new uboot + dumb dumb = Kernel Panic
January 27, 2021 08:32PM
Thanks Bodhi
I got it working.

Quote

Sandisk Cruiser Fit 16GB USB2.0
New drive, second iteration
return to previous ext3 setup 
(insert flash drive)
    $ su
    # cd /../media/rootfs/boot/
    # cp -a zImage-5.2.9-kirkwood-tld-1 backup_zImage-5.2.9-kirkwood-tld-1.bak
    # chmod -x backup_zImage-5.2.9-kirkwood-tld-1.bak
    # cp -a zImage-5.2.9-kirkwood-tld-1  zImage.fdt
    # cat dts/kirkwood-pogoplug_v4.dtb >> zImage.fdt
    # mv uImage uImage.orig
    # mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-5.2.9-kirkwood-tld-1 -d zImage.fdt  uImage
        Image Name:   Linux-5.2.9-kirkwood-tld-1
        Created:      Wed Jan 27 15:10:04 2021
        Image Type:   ARM Linux Kernel Image (uncompressed)
        Data Size:    4973578 Bytes = 4857.01 KiB = 4.74 MiB
        Load Address: 00008000
        Entry Point:  00008000
    # sync
    # cd /
    # umount /dev/sdb1
    # exit
    $ cd ../../../projects/pogoplug/kwboot/
    $ (connect pogoplug plug to power, usb to ttl converter to Pogo's UART)
    $ ./kwboot -t -B 115200 /dev/ttyUSB0 -b ./uboot.2017.07-tld-1.pogo_v4.mtd0.kwb -p
    (cycle pogo power, start twisting and separating wires, maybe do rainman dance, blow on cartridge slot, bang on it, curse at it...connects)
    ...perfection :-)

Sending boot message. Please reboot the target.../
Sending boot image...
0 % [......................................................................]
1 % [......................................................................]
...
97 % [......................................................................]
99 % [....................................]

U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:34:01 -0700)
Pogoplug V4

SoC: Kirkwood 88F6192_A1
DRAM: 128 MiB
WARNING: Caches not enabled
NAND: 128 MiB
MMC: MVEBU_MMC: 0
*** Warning - bad CRC, using default environment

In: serial
Out: serial
Err: serial
Net: egiga0
Hit any key to stop autoboot: 0
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices...
Use USB retry period from the environment: 15 second(s)
1 Storage Device(s) found

Reset IDE: ide_preinit failed
Card did not respond to voltage select!
mmc_init: -95, time 14

Partition Map for USB device 0 -- Partition Type: DOS

Part Start Sector Num Sectors UUID Type
1 32 30031840 00000000-01 0c

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **

no IDE devices available
Card did not respond to voltage select!
mmc_init: -95, time 14
running scan_disk ...
Scan device usb
device usb 0:1
1 bytes read in 692 ms (0 Bytes/s)
Found bootable drive on usb 0
loading uImage ...
4973642 bytes read in 1006 ms (4.7 MiB/s)
loading uInitrd ...
9713936 bytes read in 932 ms (9.9 MiB/s)
loading DTB /boot/dts/kirkwood-pogoplug_v4 ...
** File not found /boot/dts/kirkwood-pogoplug_v4 **
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-5.2.9-kirkwood-tld-1
Created: 2021-01-27 23:10:04 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4973578 Bytes = 4.7 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-5.2.9-kirkwood-tld-1
Created: 2019-08-25 2:22:50 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 9713872 Bytes = 9.3 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Loading Ramdisk to 071c6000, end 07b098d0 ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 5.2.9-kirkwood-tld-1 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 PREEMPT Sat Aug 17 15:00:56 PDT 2019
[ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: Pogoplug v4
[ 0.000000][ T0] Memory policy: Data cache writeback
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 32512
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
[ 0.000000][ T0] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000][ T0] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000][ T0] Memory: 104836K/131072K available (9216K kernel code, 868K rwdata, 3400K rodata, 1024K init, 301K bss, 26236K reserved, 0K cma-reserved)
[ 0.000000][ T0] random: get_random_u32 called from cache_alloc_refill+0x38c/0x928 with crng_init=0
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[ 0.000013][ T0] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[ 0.000073][ T0] Switching to timer-based delay loop, resolution 6ns
[ 0.001200][ T0] Console: colour dummy device 80x30
[ 0.001280][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666)
[ 0.001319][ T0] pid_max: default: 32768 minimum: 301
[ 0.001872][ T0] LSM: Security Framework initializing
[ 0.002155][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.002197][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.003496][ T0] *** VALIDATE proc ***
[ 0.003894][ T0] *** VALIDATE cgroup1 ***
[ 0.003931][ T0] *** VALIDATE cgroup2 ***
[ 0.004080][ T0] CPU: Testing write buffer coherency: ok
[ 0.006708][ T1] Setting up static identity map for 0x100000 - 0x100058
[ 0.007153][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[ 0.007593][ T1] rcu: Hierarchical SRCU implementation.
[ 0.012655][ T1] devtmpfs: initialized
[ 0.020217][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.020268][ T1] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.020649][ T1] xor: measuring software checksum speed
[ 0.120173][ T1] arm4regs : 699.200 MB/sec
[ 0.220119][ T1] 8regs : 435.600 MB/sec
[ 0.320113][ T1] 32regs : 633.200 MB/sec
[ 0.320142][ T1] xor: using function: arm4regs (699.200 MB/sec)
[ 0.320173][ T1] prandom: seed boundary self test passed
[ 0.326439][ T1] prandom: 100 self tests passed
[ 0.326458][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.328635][ T1] NET: Registered protocol family 16
[ 0.329513][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.330848][ T1] audit: initializing netlink subsys (disabled)
[ 0.332819][ T14] audit: type=2000 audit(0.330:1): state=initialized audit_enabled=0 res=1
[ 0.333005][ T1] cpuidle: using governor ladder
[ 0.333124][ T1] cpuidle: using governor menu
[ 0.333940][ T1] Feroceon L2: Enabling L2
[ 0.334012][ T1] Feroceon L2: Cache support initialised.
[ 0.342452][ T1] No ATAGs?
[ 2.560082][ C0] random: fast init done
[ 9.236072][ T71] alg: No test for lzo-rle (lzo-rle-generic)
[ 9.236562][ T73] alg: No test for lzo-rle (lzo-rle-scomp)
[ 9.420705][ T1] raid6: int32x8 gen() 86 MB/s
[ 9.590690][ T1] raid6: int32x8 xor() 58 MB/s
[ 9.760475][ T1] raid6: int32x4 gen() 88 MB/s
[ 9.930180][ T1] raid6: int32x4 xor() 57 MB/s
[ 10.100643][ T1] raid6: int32x2 gen() 93 MB/s
[ 10.270321][ T1] raid6: int32x2 xor() 66 MB/s
[ 10.440563][ T1] raid6: int32x1 gen() 75 MB/s
[ 10.610518][ T1] raid6: int32x1 xor() 50 MB/s
[ 10.610534][ T1] raid6: using algorithm int32x2 gen() 93 MB/s
[ 10.610546][ T1] raid6: .... xor() 66 MB/s, rmw enabled
[ 10.610559][ T1] raid6: using intx1 recovery algorithm
[ 10.610928][ T1] vgaarb: loaded
[ 10.611676][ T1] SCSI subsystem initialized
[ 10.612386][ T1] usbcore: registered new interface driver usbfs
[ 10.612474][ T1] usbcore: registered new interface driver hub
[ 10.612611][ T1] usbcore: registered new device driver usb
[ 10.612868][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 10.612885][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 10.612924][ T1] PTP clock support registered
[ 10.614818][ T1] clocksource: Switched to clocksource orion_clocksource
[ 12.160026][ T1] VFS: Disk quotas dquot_6.6.0
[ 12.160162][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 12.173812][ T1] NET: Registered protocol family 2
[ 12.175109][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes)
[ 12.175162][ T1] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 12.175197][ T1] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 12.175228][ T1] TCP: Hash tables configured (established 1024 bind 1024)
[ 12.175377][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 12.175416][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 12.175743][ T1] NET: Registered protocol family 1
[ 12.176689][ T1] RPC: Registered named UNIX socket transport module.
[ 12.176709][ T1] RPC: Registered udp transport module.
[ 12.176722][ T1] RPC: Registered tcp transport module.
[ 12.176734][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 12.176756][ T1] PCI: CLS 0 bytes, default 32
[ 12.177105][ T1] Trying to unpack rootfs image as initramfs...
[ 13.421634][ T1] Freeing initrd memory: 9488K
[ 13.421911][ T1] NetWinder Floating Point Emulator V0.97 (double precision)
[ 13.423672][ T1] Initialise system trusted keyrings
[ 13.423750][ T1] Key type blacklist registered
[ 13.424088][ T1] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[ 13.424244][ T1] zbud: loaded
[ 13.426027][ T1] NFS: Registering the id_resolver key type
[ 13.426080][ T1] Key type id_resolver registered
[ 13.426094][ T1] Key type id_legacy registered
[ 13.426123][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 13.426148][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 13.426568][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 13.426915][ T1] fuse: init (API version 7.31)
[ 13.427482][ T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 13.427757][ T1] orangefs_init: module version upstream loaded
[ 13.427777][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, no debug enabled
[ 13.452755][ T1] async_tx: api initialized (async)
[ 13.452791][ T1] Key type asymmetric registered
[ 13.452806][ T1] Asymmetric key parser 'x509' registered
[ 13.452913][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[ 13.454344][ T1] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 47
[ 13.454371][ T1] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 49
[ 13.455071][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 13.457884][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00
[ 13.457918][ T1] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 13.457941][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[ 13.457962][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 13.458111][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400
[ 13.458172][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[ 13.459891][ T1] PCI: bus0: Fast back to back transfers disabled
[ 13.459931][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 13.460204][ T1] pci 0000:01:00.0: [1b73:1009] type 00 class 0x0c0330
[ 13.460264][ T1] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x0000ffff 64bit]
[ 13.460299][ T1] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit]
[ 13.460332][ T1] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit]
[ 13.460453][ T1] pci 0000:01:00.0: supports D1
[ 13.460475][ T1] pci 0000:01:00.0: PME# supported from D0 D1 D3hot
[ 13.460569][ T1] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
[ 13.486259][ T1] PCI: bus1: Fast back to back transfers disabled
[ 13.486300][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 13.486605][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff]
[ 13.486632][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0100000-0xe01007ff pref]
[ 13.486663][ T1] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff 64bit]
[ 13.486698][ T1] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0010000-0xe0010fff 64bit]
[ 13.486732][ T1] pci 0000:01:00.0: BAR 4: assigned [mem 0xe0011000-0xe0011fff 64bit]
[ 13.486762][ T1] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 13.486790][ T1] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff]
[ 13.486952][ T1] pcieport 0000:00:01.0: enabling device (0140 -> 0142)
[ 13.487071][ T1] pci 0000:01:00.0: enabling device (0140 -> 0142)
[ 13.487884][ T1] mv_xor f1060800.xor: Marvell shared XOR driver
[ 13.546019][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 13.548980][ T1] mv_xor f1060900.xor: Marvell shared XOR driver
[ 13.606044][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 13.609407][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 13.611297][ T1] printk: console [ttyS0] disabled
[ 13.611405][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 10416666) is a 16550A
[ 14.568005][ T1] printk: console [ttyS0] enabled
[ 14.583948][ T1] loop: module loaded
[ 14.588685][ T1] sata_mv f1080000.sata: slots 32 ports 2
[ 14.598265][ T1] scsi host0: sata_mv
[ 14.602958][ T1] scsi host1: sata_mv
[ 14.607321][ T1] ata1: SATA max UDMA/133 irq 32
[ 14.612101][ T1] ata2: SATA max UDMA/133 irq 32
[ 14.618747][ T1] Could not find a valid ONFI parameter page, trying bit-wise majority to recover it
[ 14.628320][ T1] ONFI parameter recovery failed, aborting
[ 14.633970][ T1] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[ 14.641022][ T1] nand: Hynix NAND 128MiB 3,3V 8-bit
[ 14.646171][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 14.654422][ T1] Scanning device for bad blocks
[ 14.679040][ T1] Bad eraseblock 240 at 0x000001e00000
[ 14.748827][ T1] 5 cmdlinepart partitions found on MTD device orion_nand
[ 14.755792][ T1] Creating 5 MTD partitions on "orion_nand":
[ 14.761613][ T1] 0x000000000000-0x000000200000 : "u-boot"
[ 14.769206][ T1] 0x000000200000-0x000000500000 : "uImage"
[ 14.776667][ T1] 0x000000500000-0x000000800000 : "uImage2"
[ 14.784135][ T1] 0x000000800000-0x000001000000 : "failsafe"
[ 14.791809][ T1] 0x000001000000-0x000008000000 : "root"
[ 14.801356][ T1] libphy: Fixed MDIO Bus: probed
[ 14.807364][ T1] libphy: orion_mdio_bus: probed
[ 14.832840][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 14.841193][ T1] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set
[ 14.949563][ T112] ata1: SATA link down (SStatus 0 SControl F300)
[ 15.296741][ T114] ata2: SATA link down (SStatus 0 SControl F300)
[ 15.565789][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address ************
[ 15.575394][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 15.582626][ T1] ehci-pci: EHCI PCI platform driver
[ 15.587860][ T1] ehci-orion: EHCI orion driver
[ 15.592844][ T1] orion-ehci f1050000.ehci: EHCI Host Controller
[ 15.599079][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 15.607682][ T1] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
[ 15.634873][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 15.641958][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02
[ 15.650922][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 15.658841][ T1] usb usb1: Product: EHCI Host Controller
[ 15.664394][ T1] usb usb1: Manufacturer: Linux 5.2.9-kirkwood-tld-1 ehci_hcd
[ 15.671703][ T1] usb usb1: SerialNumber: f1050000.ehci
[ 15.677963][ T1] hub 1-0:1.0: USB hub found
[ 15.682452][ T1] hub 1-0:1.0: 1 port detected
[ 15.688288][ T1] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 15.694221][ T1] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[ 15.703805][ T1] xhci_hcd 0000:01:00.0: hcc params 0x200073a1 hci version 0x100 quirks 0x0000000000080010
[ 15.714384][ T1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02
[ 15.723354][ T1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 15.731270][ T1] usb usb2: Product: xHCI Host Controller
[ 15.736850][ T1] usb usb2: Manufacturer: Linux 5.2.9-kirkwood-tld-1 xhci-hcd
[ 15.744132][ T1] usb usb2: SerialNumber: 0000:01:00.0
[ 15.750235][ T1] hub 2-0:1.0: USB hub found
[ 15.754729][ T1] hub 2-0:1.0: 2 ports detected
[ 15.760256][ T1] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 15.766266][ T1] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3
[ 15.774345][ T1] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed
[ 15.781472][ T1] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 15.790469][ T1] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.02
[ 15.799572][ T1] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 15.807497][ T1] usb usb3: Product: xHCI Host Controller
[ 15.813055][ T1] usb usb3: Manufacturer: Linux 5.2.9-kirkwood-tld-1 xhci-hcd
[ 15.820365][ T1] usb usb3: SerialNumber: 0000:01:00.0
[ 15.826446][ T1] hub 3-0:1.0: USB hub found
[ 15.830943][ T1] hub 3-0:1.0: 2 ports detected
[ 15.836771][ T1] usbcore: registered new interface driver usb-storage
[ 15.843946][ T1] mousedev: PS/2 mouse device common for all mice
[ 16.054869][ T15] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 16.255934][ T15] usb 1-1: New USB device found, idVendor=0781, idProduct=5571, bcdDevice= 1.00
[ 16.264800][ T15] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 16.272662][ T15] usb 1-1: Product: Cruzer Fit
[ 16.277291][ T15] usb 1-1: Manufacturer: SanDisk'
[ 16.282154][ T15] usb 1-1: SerialNumber: **********************
[ 16.289071][ T15] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 16.296499][ T15] scsi host2: usb-storage 1-1:1.0
[ 16.884871][ T1] rtc-mv f1010300.rtc: internal RTC not ticking
[ 16.891193][ T1] i2c /dev entries driver
[ 16.896351][ T1] device-mapper: uevent: version 1.0.3
[ 16.902035][ T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com
[ 16.911763][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 16.919059][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 16.926402][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 16.933780][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 16.940584][ T1] device-mapper: raid: Loading target version 1.14.0
[ 16.948674][ T1] hidraw: raw HID events driver (C) Jiri Kosina
[ 16.955267][ T1] drop_monitor: Initializing network drop monitor service
[ 16.962684][ T1] NET: Registered protocol family 17
[ 16.968203][ T1] Key type dns_resolver registered
[ 16.974324][ T1] registered taskstats version 1
[ 16.979155][ T1] Loading compiled-in X.509 certificates
[ 16.984731][ T1] zswap: loaded using pool lzo/zbud
[ 17.123089][ T1] Key type big_key registered
[ 17.188503][ T1] Key type encrypted registered
[ 17.196205][ T1] hctosys: unable to open rtc device (rtc0)
[ 17.206971][ T1] Freeing unused kernel memory: 1024K
[ 17.215953][ T1] Checked W+X mappings: passed, no W+X pages found
[ 17.222288][ T1] Run /init as init process
Loading, please wait...
[ 17.367378][ T23] scsi 2:0:0:0: Direct-Access SanDisk' Cruzer Fit 1.00 PQ: 0 ANSI: 6
[ 17.387043][ T7] sd 2:0:0:0: [sda] 30031872 512-byte logical blocks: (15.4 GB/14.3 GiB)
[ 17.405278][ T7] sd 2:0:0:0: [sda] Write Protect is off
[ 17.414991][ T7] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 17.442111][ T7] sda: sda1
[ 17.458996][ T7] sd 2:0:0:0: [sda] Attached SCSI removable disk
Starting version 241
[ 18.607062][ T167] usbcore: registered new interface driver uas
[ 18.736577][ T164] mvsdio f1090000.mvsdio: Got CD GPIO
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.33.1
[/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1
rootfs: clean, 15076/940240 files, 220947/3753980 blocks
done.
[ 29.523018][ T193] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 29.577238][ T193] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.93 booting
[info] Using makefile-style concurrent boot in runlevel S.
[ ok ] Starting hotplug events dispatcher: systemd-udevd.
[ ok ] Synthesizing the initial hotplug events (subsystems)...done.
[....] Synthesizing the initial hotplug events (devices)...[ 33.290325][ T372] input: gpio_keys as /devices/platform/gpio_keys/input/input0
done.
[....] Waiting for /dev to be fully populated...[ 33.622363][ T394] systemd-udevd[394]: Using default interface naming scheme 'v240'.
[ 33.710115][ T394] systemd-udevd[394]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 33.928848][ C0] random: crng init done
[ 33.949965][ T393] watchdog: f1020300.watchdog-timer: driver supplied timeout (4294967295) out of range
[ 34.090811][ T393] watchdog: f1020300.watchdog-timer: falling back to default timeout (25)
[ 34.247982][ T393] orion_wdt: Initial timeout 25 sec
[ 34.383024][ T374] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 34.515307][ T395] marvell-cesa f1030000.crypto: CESA device successfully registered
[ 34.671007][ T392] systemd-udevd[392]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
done.
[ ok ] Setting hostname to 'debian'...done.
[ ok ] Activating swap:.
[ 36.378403][ T590] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[info] Will now check all file systems.
fsck from util-linux 2.33.1
Checking all file systems.
LABEL=rootfs is mounted
[....] Done checking file systems. A log is being saved in /var/log/fsck/check[ ok that location is writable..
[ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done.
[ ok .
[ ok ] Will now mount local filesystems:.
[ ok ] Will now activate swapfile swap:done.
[ ok ] Checking minimum space in /tmp...done.
[ ok ] Cleaning up temporary files....
[ ok ] Starting Setting kernel variables: sysctl.
[ ok ] Initializing random number generator...done.
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1
Copyright 2004-2018 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Listening on LPF/eth0/52:3b:20:9c:11:51
Sending on LPF/eth0/52:3b:20:9c:11:51
Sending on Socket/fallback
DHCPREQUEST for 192.168.0.15 on eth0 to 255.255.255.255 port 67
DHCPREQUEST for 192.168.0.15 on eth0 to 255.255.255.255 port 67
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 21
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 14
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 9
No DHCPOFFERS received.
Trying recorded lease 192.168.0.15
[ 120.215389][ T1120] NET: Registered protocol family 10
[ 120.226798][ T1120] Segment Routing with IPv6
PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data.

--- 192.168.0.1 ping statistics ---
1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms

No working leases in persistent database - sleeping.
done.
[ ok ] Starting RPC port mapper daemon: rpcbind.
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1326 (syslogd)
. ok
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1353 (klogd)
. ok
[ ok ] Starting system message bus: dbus.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting NFS common utilities: statd idmapd.
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[ ok ] Running local boot scripts (/etc/rc.local).

Debian GNU/Linux 10 debian ttyS0

debian login: root
Password: root
Last login: Wed Dec 31 16:02:34 PST 1969 from 192.168.0.100 on pts/0
Linux debian 5.2.9-kirkwood-tld-1 #1 PREEMPT Sat Aug 17 15:00:56 PDT 2019 armv5tel

The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.

Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law. 
root@debian:~#
Thanks again!
-Jake



Edited 1 time(s). Last edit at 01/27/2021 08:37PM by Jake.
Reply Quote
bodhi
Re: Pogoplug Series 4 V4-A03-01 PreInternet new uboot + dumb dumb = Kernel Panic
January 27, 2021 09:50PM
> (cycle pogo power, start twisting and
> separating wires, maybe do rainman dance, blow on
> cartridge slot, bang on it, curse at
> it...connects)
> ...perfection :-)

You forgot to say bodhi's name 3 times :))

Cool!

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Reply Quote
Newer Topic Older Topic
Author:

Your Email:


Subject:
Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: