|
DS216 play Redboot problem? April 20, 2021 03:56PM |
Registered: 2 years ago Posts: 3 |
U-Boot 2014.01-g982ae47-dirty (Dec 11 2015 - 09:47:34) - stm24-2014-09-25
Board: B2120-revc-STxH410 [ARM]
I2C: ready
DRAM: 1 GiB
SPI: info: found ST N25Q064 (8MiB) device (page=256,erase=65536)
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Synology Model: DS216play
Fan Status: Good
Net: stmac-1
Warning: stmac-1 using MAC address from net device
USB0: Register 2000240 NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
Transcoding memorylayout: 1 channel mode.
Press Ctrl+C to abort autoboot in 3 second
EEPROM @0x0 read: addr 4f000000 off 60000 count 393216 ... done
EEPROM @0x0 read: addr 44000000 off 390000 count 4456448 ... done
EEPROM @0x0 read: addr 43000000 off c0000 count 2949120 ... done
## Booting kernel from Legacy Image at 43000000 ...
Image Name: Linux-3.10.105
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2716320 Bytes = 2.6 MiB
Load Address: 43008000
Entry Point: 43008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 44000000 ...
Image Name: synology_monaco_ds216play 24922
Image Type: ARM Linux RAMDisk Image (uncompressed)
Data Size: 4153493 Bytes = 4 MiB
Load Address: 44000000
Entry Point: 44000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 4f000000
Booting using the fdt blob at 0x4f000000
Loading Kernel Image ... OK
Loading Ramdisk to 43c08000, end 43ffe095 ... OK
Using Device Tree in place at 4f000000, end 4f02abcc
Starting kernel ...
Using FDT blob at 0x4f000000
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.10.105 (root@build9) (gcc version 4.9.3 20150311 (prerelease) (crosstool-NG 1.20.0) ) #24922 SMP Fri May 10 02:58:37 CST 2019
[ 0.000000] Machine: STi SoC with Flattened Device Tree, model: STiH410 B2120
[ 0.000000] Ignoring memory below PHYS_OFFSET: 0x40000000-0x43000000
[ 0.000000] Ignoring memory below PHYS_OFFSET: 0x42000000-0x43000000
[ 0.000000] cma: CMA: reserved 16 MiB at 6e000000
[ 0.000000] PERCPU: Embedded 7 pages/cpu @815cf000 s6976 r8192 d13504 u32768
[ 0.000000] Kernel command line: console=ttyS0,115200 CONSOLE=/dev/ttyS0 ip=o ff mtdparts=stm-nand-bch.0:0x500000(boot),-(rfs) bpa2parts=BPA2_Region|aud-coded |aud-transcoded|vid-coded|vid-transcoded|vid-raw-input|vid-output-0|vid-decimate d-1|vid-copied-1|vid-macroblock-0|vid-extra-data-0|vid-extra-data-1|v4l2-coded-v ideo-buffers|vid-enc-data-0|vid-enc-scaled-0|vid-encoded-0|v4l2-clut|v4l2-grab|g fx-memory|aud-codec-data|vid-codec-data|aud-output-0|aud-output-1|vid-output-1|v id-decimated-0|vid-copied-0|vid-macroblock-1|blitter|vid-enc-data-1|vid-enc-scal ed-1|vid-encoded-1|coredisplay-video|multicom|hades-l3|BPA2_Region0|BPA2_Region1 :240M:0x71000000,v4l2-vb2|v4l2-stmc8jpg|v4l2-stmvout|v4l2-compo:24M:0x6F800000,c oprocs:32M:0x40000000,modules|audio:8M:0x6F000000,bigphysarea|te-buffers|m2m-ca3 :32M:0x48000000,STMCReserve:32768:0x47FF8000 vmalloc=535m mem=720m@0x42000000 ro ot=/dev/md0 rw syno_hw_version=DS216play hd_power_on_seq=2 ihd_num=2 netif_num=1 flash_size=8 phys_memsize=1024 syno_mem_mod[ 0.000000] bpa2: partition 'BPA2 _Region' created at 0x71000000 (high), size 245760 kB (0x0f000000 B)
[ 0.000000] bpa2: partition 'v4l2-vb2' created at 0x6f800000 (high), size 245 76 kB (0x01800000 B)
[ 0.000000] bpa2: partition 'coprocs' created at 0x40000000 (high), size 3276 8 kB (0x02000000 B)
[ 0.000000] bpa2: partition 'modules' created at 0x6f000000 (high), size 8192 kB (0x00800000 B)
[ 0.000000] bpa2: partition 'bigphysarea' created at 0x48000000 (low), size 3 2768 kB (0x02000000 B)
[ 0.000000] bpa2: partition 'STMCReserve' created at 0x47ff8000 (low), size 3 2 kB (0x00008000 B)
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 704MB = 704MB total
[ 0.000000] Memory: 653248k/653248k available, 67648k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xac800000 - 0xff000000 (1320 MB)
[ 0.000000] lowmem : 0x80000000 - 0xac000000 ( 704 MB)
[ 0.000000] modules : 0x7f000000 - 0x80000000 ( 16 MB)
[ 0.000000] .text : 0x80008000 - 0x80665b18 (6519 kB)
[ 0.000000] .init : 0x80666000 - 0x806a0b40 ( 235 kB)
[ 0.000000] .data : 0x806a2000 - 0x806dea00 ( 243 kB)
[ 0.000000] .bss : 0x806dea00 - 0x8073ac24 ( 369 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] st-lpc: lpc_clk running @ 30000000 Hz
[ 0.000000] sched_clock: 32 bits at 30MHz, resolution 33ns, wraps every 14316 5ms
[ 0.000000] st-lpc: clocksource initialised: iomem: ac81c000
[ 0.000000] L310 cache controller enabled
[ 0.000000] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x10480000, Cache siz e: 1048576 B
[ 0.000000] Console: colour dummy device 80x30
[ 0.001807] Calibrating delay loop... 2996.63 BogoMIPS (lpj=14983168)
[ 0.060212] pid_max: default: 32768 minimum: 301
[ 0.060282] Security Framework initialized
[ 0.060297] AppArmor: AppArmor initialized
[ 0.060324] Mount-cache hash table entries: 512
[ 0.060686] CPU: Testing write buffer coherency: ok
[ 0.060992] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.061567] Setting up static identity map for 0x804c6b50 - 0x804c6c2c
[ 0.120233] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.120283] Brought up 2 CPUs
[ 0.120293] SMP: Total of 2 processors activated (5985.89 BogoMIPS).
[ 0.120297] CPU: All CPU(s) started in SVC mode.
[ 0.120649] devtmpfs: initialized
[ 0.123771] xor: measuring software checksum speed
[ 0.220220] arm4regs : 2325.200 MB/sec
[ 0.320221] 8regs : 1668.400 MB/sec
[ 0.420220] 32regs : 1695.200 MB/sec
[ 0.420225] xor: using function: arm4regs (2325.200 MB/sec)
[ 0.420232] pinctrl core: initialized pinctrl subsystem
[ 0.420580] regulator-dummy: no parameters
[ 0.421171] NET: Registered protocol family 16
[ 0.424367] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[ 0.428531] syscon 9620000.sbc-syscfg: regmap [mem 0x09620000-0x09620fff] reg istered
[ 0.428668] syscon 9280000.front-syscfg: regmap [mem 0x09280000-0x09280fff] r egistered
[ 0.428792] syscon 9290000.rear-syscfg: regmap [mem 0x09290000-0x09290fff] re gistered
[ 0.428911] syscon 92a0000.flash-syscfg: regmap [mem 0x092a0000-0x092a0fff] r egistered
[ 0.429042] syscon 9600000.fvdp-lite-syscfg: regmap [mem 0x09600000-0x09600ff f] registered
[ 0.429161] syscon 92b0000.core-syscfg: regmap [mem 0x092b0000-0x092b0fff] re gistered
[ 0.429284] syscon 94b5100.lpm-syscfg: regmap [mem 0x094b5100-0x094b60ff] reg istered
[ 0.442595] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.442603] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.442754] st-pinctrl 961f080.pin-controller-sbc: nbanks = 6
[ 0.442760] st-pinctrl 961f080.pin-controller-sbc: nfunctions = 14
[ 0.442766] st-pinctrl 961f080.pin-controller-sbc: ngroups = 27
[ 0.442912] st-pinctrl 961f080.pin-controller-sbc: PIO0 bank added.
[ 0.443091] st-pinctrl 961f080.pin-controller-sbc: PIO1 bank added.
[ 0.443250] st-pinctrl 961f080.pin-controller-sbc: PIO2 bank added.
[ 0.443419] st-pinctrl 961f080.pin-controller-sbc: PIO3 bank added.
[ 0.443576] st-pinctrl 961f080.pin-controller-sbc: PIO4 bank added.
[ 0.443734] st-pinctrl 961f080.pin-controller-sbc: PIO5 bank added.
[ 0.443821] st-pinctrl 961f080.pin-controller-sbc: Function[0 name:wa keup-pin, groups:1]
[ 0.443832] st-pinctrl 961f080.pin-controller-sbc: Function[1 name:rc , groups:1]
[ 0.443842] st-pinctrl 961f080.pin-controller-sbc: Function[2 name:sb c_serial0, groups:1]
[ 0.443852] st-pinctrl 961f080.pin-controller-sbc: Function[3 name:sb c_serial1, groups:1]
[ 0.443862] st-pinctrl 961f080.pin-controller-sbc: Function[4 name:i2 c10, groups:1]
[ 0.443872] st-pinctrl 961f080.pin-controller-sbc: Function[5 name:i2 c11, groups:1]
[ 0.443888] st-pinctrl 961f080.pin-controller-sbc: Function[6 name:ke yscan, groups:1]
[ 0.443944] st-pinctrl 961f080.pin-controller-sbc: Function[7 name:gm ac1, groups:8]
[ 0.443958] st-pinctrl 961f080.pin-controller-sbc: Function[8 name:pw m1, groups:4]
[ 0.443972] st-pinctrl 961f080.pin-controller-sbc: Function[9 name:sp i10, groups:2]
[ 0.443986] st-pinctrl 961f080.pin-controller-sbc: Function[10 name:sp i11, groups:2]
[ 0.443999] st-pinctrl 961f080.pin-controller-sbc: Function[11 name:sp i12, groups:2]
[ 0.444008] st-pinctrl 961f080.pin-controller-sbc: Function[12 name:ce c0, groups:1]
[ 0.444026] st-pinctrl 961f080.pin-controller-sbc: Function[13 name:hd mirx0, groups:1]
[ 0.444123] st-pinctrl 920f080.pin-controller-front0: nbanks = 10
[ 0.444130] st-pinctrl 920f080.pin-controller-front0: nfunctions = 24
[ 0.444135] st-pinctrl 920f080.pin-controller-front0: ngroups = 53
[ 0.444277] st-pinctrl 920f080.pin-controller-front0: PIO10 bank added.
[ 0.444442] st-pinctrl 920f080.pin-controller-front0: PIO11 bank added.
[ 0.444605] st-pinctrl 920f080.pin-controller-front0: PIO12 bank added.
[ 0.444774] st-pinctrl 920f080.pin-controller-front0: PIO13 bank added.
[ 0.444939] st-pinctrl 920f080.pin-controller-front0: PIO14 bank added.
[ 0.445106] st-pinctrl 920f080.pin-controller-front0: PIO15 bank added.
[ 0.445273] st-pinctrl 920f080.pin-controller-front0: PIO16 bank added.
[ 0.445435] st-pinctrl 920f080.pin-controller-front0: PIO17 bank added.
[ 0.445599] st-pinctrl 920f080.pin-controller-front0: PIO18 bank added.
[ 0.445764] st-pinctrl 920f080.pin-controller-front0: PIO19 bank added.
[ 0.445858] st-pinctrl 920f080.pin-controller-front0: Function[0 name:se rial0, groups:4]
[ 0.445877] st-pinctrl 920f080.pin-controller-front0: Function[1 name:se rial1, groups:4]
[ 0.445895] st-pinctrl 920f080.pin-controller-front0: Function[2 name:se rial2, groups:1]
[ 0.445917] st-pinctrl 920f080.pin-controller-front0: Function[3 name:mm c1, groups:1]
[ 0.445928] st-pinctrl 920f080.pin-controller-front0: Function[4 name:i2 c0, groups:1]
[ 0.445939] st-pinctrl 920f080.pin-controller-front0: Function[5 name:i2 c1, groups:1]
[ 0.445949] st-pinctrl 920f080.pin-controller-front0: Function[6 name:i2 c2, groups:1]
[ 0.445967] st-pinctrl 920f080.pin-controller-front0: Function[7 name:i2 c3, groups:3]
[ 0.445991] st-pinctrl 920f080.pin-controller-front0: Function[8 name:sp i0, groups:4]
[ 0.446014] st-pinctrl 920f080.pin-controller-front0: Function[9 name:sp i1, groups:4]
[ 0.446045] st-pinctrl 920f080.pin-controller-front0: Function[10 name:sp i2, groups:6]
[ 0.446077] st-pinctrl 920f080.pin-controller-front0: Function[11 name:sp i3, groups:6]
[ 0.446098] st-pinctrl 920f080.pin-controller-front0: Function[12 name:sy strace, groups:1]
[ 0.446108] st-pinctrl 920f080.pin-controller-front0: Function[13 name:sc r0, groups:1]
[ 0.446116] st-pinctrl 920f080.pin-controller-front0: Function[14 name:sc r1, groups:1]
[ 0.446146] st-pinctrl 920f080.pin-controller-front0: Function[15 name:ts in0, groups:2]
[ 0.446178] st-pinctrl 920f080.pin-controller-front0: Function[16 name:ts in1, groups:2]
[ 0.446208] st-pinctrl 920f080.pin-controller-front0: Function[17 name:ts in2, groups:2]
[ 0.446222] st-pinctrl 920f080.pin-controller-front0: Function[18 name:ts in3, groups:1]
[ 0.446235] st-pinctrl 920f080.pin-controller-front0: Function[19 name:ts in4, groups:1]
[ 0.446258] st-pinctrl 920f080.pin-controller-front0: Function[20 name:ts in5, groups:2]
[ 0.446288] st-pinctrl 920f080.pin-controller-front0: Function[21 name:ts out0, groups:2]
[ 0.446302] st-pinctrl 920f080.pin-controller-front0: Function[22 name:ts out1, groups:1]
[ 0.446326] st-pinctrl 920f080.pin-controller-front0: Function[23 name:mt sin0, groups:1]
[ 0.446419] st-pinctrl 921f080.pin-controller-front1: nbanks = 1
[ 0.446425] st-pinctrl 921f080.pin-controller-front1: nfunctions = 1
[ 0.446431] st-pinctrl 921f080.pin-controller-front1: ngroups = 1
[ 0.446570] st-pinctrl 921f080.pin-controller-front1: PIO20 bank added.
[ 0.446672] st-pinctrl 921f080.pin-controller-front1: Function[0 name:ts in4, groups:1]
[ 0.446750] st-pinctrl 922f080.pin-controller-rear: nbanks = 6
[ 0.446756] st-pinctrl 922f080.pin-controller-rear: nfunctions = 11
[ 0.446761] st-pinctrl 922f080.pin-controller-rear: ngroups = 17
[ 0.446908] st-pinctrl 922f080.pin-controller-rear: PIO30 bank added.
[ 0.447086] st-pinctrl 922f080.pin-controller-rear: PIO31 bank added.
[ 0.447251] st-pinctrl 922f080.pin-controller-rear: PIO32 bank added.
[ 0.447407] st-pinctrl 922f080.pin-controller-rear: PIO33 bank added.
[ 0.447583] st-pinctrl 922f080.pin-controller-rear: PIO34 bank added.
[ 0.447750] st-pinctrl 922f080.pin-controller-rear: PIO35 bank added.
[ 0.447990] st-pinctrl 922f080.pin-controller-rear: Function[0 name:dv o, groups:2]
[ 0.448005] st-pinctrl 922f080.pin-controller-rear: Function[1 name:i2 c4, groups:1]
[ 0.448019] st-pinctrl 922f080.pin-controller-rear: Function[2 name:i2 c5, groups:1]
[ 0.448034] st-pinctrl 922f080.pin-controller-rear: Function[3 name:us b0, groups:1]
[ 0.448047] st-pinctrl 922f080.pin-controller-rear: Function[4 name:us b1, groups:1]
[ 0.448068] st-pinctrl 922f080.pin-controller-rear: Function[5 name:us b3, groups:1]
[ 0.448080] st-pinctrl 922f080.pin-controller-rear: Function[6 name:pw m0, groups:1]
[ 0.448116] st-pinctrl 922f080.pin-controller-rear: Function[7 name:sp i4, groups:4]
[ 0.448152] st-pinctrl 922f080.pin-controller-rear: Function[8 name:i2 s_out, groups:2]
[ 0.448189] st-pinctrl 922f080.pin-controller-rear: Function[9 name:i2 s_in, groups:2]
[ 0.448200] st-pinctrl 922f080.pin-controller-rear: Function[10 name:sp dif_out, groups:1]
[ 0.448291] st-pinctrl 923f080.pin-controller-flash: nbanks = 3
[ 0.448298] st-pinctrl 923f080.pin-controller-flash: nfunctions = 3
[ 0.448303] st-pinctrl 923f080.pin-controller-flash: ngroups = 3
[ 0.448434] st-pinctrl 923f080.pin-controller-flash: PIO40 bank added.
[ 0.448604] st-pinctrl 923f080.pin-controller-flash: PIO41 bank added.
[ 0.448774] st-pinctrl 923f080.pin-controller-flash: PIO42 bank added.
[ 0.448901] st-pinctrl 923f080.pin-controller-flash: Function[0 name:mm c0, groups:1]
[ 0.448931] st-pinctrl 923f080.pin-controller-flash: Function[1 name:fs m, groups:1]
[ 0.448994] st-pinctrl 923f080.pin-controller-flash: Function[2 name:na nd, groups:1]
[ 0.450857] reset-stih407 powerdown-controller.8: registered
[ 0.452576] reset-stih407 softreset-controller.10: registered
[ 0.452775] reset-stih407 picophyreset-controller.11: registered
[ 0.455602] st-clk clocks.0: SoC clock tree intialized
[ 0.465989] bio: create slab <bio-0> at 0
[ 1.820586] st-fdma 8e20000.fdma-mpe: IRQ: 37
[ 1.820603] st-fdma 8e20000.fdma-mpe: Base address: ac8c0000
[ 1.822196] st-fdma 8e40000.fdma-mpe: IRQ: 39
[ 1.822211] st-fdma 8e40000.fdma-mpe: Base address: ac9c0000
[ 1.823728] st-fdma 8e60000.fdma-mpe: IRQ: 41
[ 1.823750] st-fdma 8e60000.fdma-mpe: Base address: aca00000
[ 1.825521] vmmc0: at 3300 mV
[ 1.825567] st-vsense 9061004.voltage-regulator: vmmc0 vsense voltage regula tor registered
[ 1.825924] vgaarb: loaded
[ 1.826214] SCSI subsystem initialized
[ 1.826659] media: Linux media interface: v0.10
[ 1.826721] Linux video capture interface: v2.00
[ 1.826930] pps_core: LinuxPPS API ver. 1 registered
[ 1.826934] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome tti <giometti@linux.it>
[ 1.826986] PTP clock support registered
[ 1.827899] Switching to clocksource st-lpc clocksource
[ 1.828166] AppArmor: AppArmor Filesystem Enabled
[ 1.837294] NET: Registered protocol family 2
[ 1.837678] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 1.837747] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 1.837813] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.837889] TCP: reno registered
[ 1.837899] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 1.837970] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 1.838137] NET: Registered protocol family 1
[ 1.838297] RPC: Registered named UNIX socket transport module.
[ 1.838304] RPC: Registered udp transport module.
[ 1.838307] RPC: Registered tcp transport module.
[ 1.838311] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.838425] Trying to unpack rootfs image as initramfs...
[ 3.174389] Freeing initrd memory: 4056K (80c08000 - 80ffe000)
[ 3.176942] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counter s available
[ 3.178469] sti pm: Copying poke table & poke loop to buffer
[ 3.178479] sti pm: entering prepare:CONTROLLER PASSIVE STANDBY
[ 3.178484] sti pm: support mode: CONTROLLER PASSIVE STANDBY
[ 3.178488] sti pm: Suspend support registered
[ 3.178650] synology : fan ctrl initialized.
[ 3.178661] synology : fan sense initialized.
[ 3.178673] synology : sata power initialized.
[ 3.178689] synology : model id initialized.
[ 3.178698] synology : disk led ctrl initialized.
[ 3.178705] synology : phy led ctrl initialized.
[ 3.180063] Initialise module verification
[ 3.180088] audit: initializing netlink socket (disabled)
[ 3.180111] type=2000 audit(3.170:1): initialized
[ 3.226497] st-pinctrl 920f080.pin-controller-front0: maps: function systrace group systrace-default num 6
[ 3.226608] stm-systrace 9180000.systrace: Systrace: syscfg0=0x003f0000 (prev : 0x003f0000)
[ 3.226619] stm-systrace 9180000.systrace: Systrace: syscfg1=0x00580058 (prev : 0x00580058)
[ 3.226628] stm-systrace 9180000.systrace: Systrace: syscfg2=0x00990098 (prev : 0x00990098)
[ 3.226636] stm-systrace 9180000.systrace: Systrace: syscfg3=0x00530050 (prev : 0x00530050)
[ 3.226645] stm-systrace 9180000.systrace: Systrace: syscfg4=0x00550054 (prev : 0x00550054)
[ 3.226653] stm-systrace 9180000.systrace: Systrace: syscfg5=0x00570056 (prev : 0x00570056)
[ 3.226662] stm-systrace 9180000.systrace: Systrace: syscfg6=0x03ff03ff (prev : 0x03ff0000)
[ 3.226672] stm-systrace 9180000.systrace: Systrace: STM_CR[0x0000] = 0x00000 600 (prev. 0x00000000)
[ 3.226680] stm-systrace 9180000.systrace: Systrace: STM_MCR[0x0008] = 0x0000 0000 (prev. 0x00000000)
[ 3.226688] stm-systrace 9180000.systrace: Systrace: STM_TER[0x0010] = 0x0000 03ff (prev. 0x000003ff)
[ 3.226696] stm-systrace 9180000.systrace: Systrace: STM_FTR[0x0080] = 0x0000 0001 (prev. 0x00000000)
[ 3.226704] stm-systrace 9180000.systrace: Systrace: STM_CTR[0x0088] = 0x0000 0001 (prev. 0x00000000)
[ 3.226710] Systrace: STM IP revision is V3
[ 3.226714] Systrace: STM_PID=0x00680dec(0x00680dec)
[ 3.226717] Systrace: STM_CID=0xb105f00d(0xb105f00d)
[ 3.226722] MTT: registering output driver stm
[ 3.226727] stm-systrace 9180000.systrace: Systrace: driver probed.
[ 3.239146] VFS: Disk quotas dquot_6.5.2
[ 3.242481] NFS: Registering the id_resolver key type
[ 3.242511] Key type id_resolver registered
[ 3.242516] Key type id_legacy registered
[ 3.242541] msgmni has been set to 1315
[ 3.243185] async_tx: api initialized (async)
[ 3.243193] Key type asymmetric registered
[ 3.243198] Asymmetric key parser 'x509' registered
[ 3.243604] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 50)
[ 3.243613] io scheduler noop registered
[ 3.243628] io scheduler cfq registered (default)
[ 3.364447] STMicroelectronics ASC driver initialized
[ 3.364593] st-pinctrl 961f080.pin-controller-sbc: maps: function sbc_serial0 group sbc_serial0-0 num 3
[ 3.364688] 9530000.serial: ttyS0 at MMIO 0x9530000 (irq = 170) is a st-asc
[ 5.022688] console [ttyS0] enabled
[ 5.026515] st-pinctrl 961f080.pin-controller-sbc: maps: function sbc_serial1 group sbc_serial1-0 num 3
[ 5.035978] 9531000.serial: ttyS1 at MMIO 0x9531000 (irq = 171) is a st-asc
[ 5.043953] st-hwrandom 8a89000.rng: ST Random Number Generator Device Probe Successful
[ 5.060618] brd: module loaded
[ 5.063663] Loading iSCSI transport class v2.0-870.
[ 5.071210] ahci ahci.0: can't get clock
[ 5.075130] miphy28lp-phy 9b22000.miphy28lp: miphy28lp_phy_init_sata
[ 5.081486] miphy28lp-phy 9b22000.miphy28lp: sata-up mode, addr 0xac8e4000
[ 5.092424] ahci ahci.0: forcing PORTS_IMPL to 0x1
[ 5.097226] ahci ahci.0: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl plat form mode
[ 5.105145] ahci ahci.0: flags: ncq sntf pm led clo only pmp pio slum part cc c apst
[ 5.114421] scsi0 : ahci_platform
[ 5.118241] ata1: SATA max UDMA/133 mmio [mem 0x09b20000-0x09b20fff] port 0x1 00 irq 191
[ 8.467945] ata1: SATA link down (SStatus 0 SControl 300)
[ 8.473332] ata1: No present pin info for SATA link down event
[ 8.479582] ahci ahci.1: can't get clock
[ 8.483498] miphy28lp-phy 9b2a000.miphy28lp: miphy28lp_phy_init_sata
[ 8.489857] miphy28lp-phy 9b2a000.miphy28lp: sata-up mode, addr 0xac8ea000
[ 8.498604] ahci ahci.1: forcing PORTS_IMPL to 0x1
[ 8.503403] ahci ahci.1: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl plat form mode
[ 8.511320] ahci ahci.1: flags: ncq sntf pm led clo only pmp pio slum part cc c apst
[ 8.520327] scsi1 : ahci_platform
[ 8.524071] ata2: SATA max UDMA/133 mmio [mem 0x09b28000-0x09b28fff] port 0x1 00 irq 202
[ 16.857945] ata2: SATA link down (SStatus 0 SControl 300)
[ 16.863330] ata2: No present pin info for SATA link down event
[ 16.870597] st-pinctrl 923f080.pin-controller-flash: maps: function fsm group fsm num 7
[ 16.878853] stm-spi-fsm 9022000.spifsm: No provision for SPI reset on boot-fr om-spi system
[ 16.887106] stm-spi-fsm 9022000.spifsm: Individual block locking scheme enabl ed
[ 16.894413] stm-spi-fsm 9022000.spifsm: found device: n25q064, size = 800000 (8MiB) erasesize = 0x00010000 (64KiB)
[ 16.904773] Searching for RedBoot partition table in n25q064 at offset 0x7f00 00
[ 16.917253] No RedBoot partition table detected in n25q064
[ 16.926734] st-pinctrl 961f080.pin-controller-sbc: maps: function gmac1 group rgmii1-0 num 13
[ 16.935271] st-pinctrl 961f080.pin-controller-sbc: maps: function gmac1 group rgmii1-mdio num 3
[ 16.944143] stmmaceth 9630000.dwmac: phy-addr property limits bus scan to thi s addr
[ 16.951902] stmmac - user ID: 0xca, Synopsys ID: 0x37
[ 16.956938] Ring mode enabled
[ 16.959986] DMA HW capability register supported
[ 16.964500] Enhanced/Alternate descriptors
[ 16.968848] Enabled extended descriptors
[ 16.972842] RX Checksum Offload Engine supported (type 2)
[ 16.978318] TX Checksum insertion supported
[ 16.982573] Wake-Up On Lan supported
[ 16.986235] Enable RX Mitigation via HW Watchdog Timer
[ 16.992707] libphy: stmmac: probed
[ 16.996100] eth0: PHY ID 001cc915 at 1 IRQ POLL (stmmac-0:01) active
[ 17.003398] i2c /dev entries driver
[ 17.007142] st-pinctrl 922f080.pin-controller-rear: maps: function i2c4 group i2c4-default num 3
[ 17.016634] st-i2c 9844000.i2c: ST I2C(0x0) initialized
[ 17.021908] st-pinctrl 922f080.pin-controller-rear: maps: function i2c5 group i2c5-default num 3
[ 17.030731] st-i2c 9845000.i2c: No ID specified in DT alias
[ 17.038807] st_thermal 91a0000.temp0: STMicroelectronics thermal sensor initi alised
[ 17.047427] st-lpc-wdt 8787000.lpc_wdt: LPC Watchdog driver registered, reset type is cold
[ 17.056081] md: linear personality registered for level -1
[ 17.061588] md: raid0 personality registered for level 0
[ 17.066884] md: raid1 personality registered for level 1
[ 17.072189] md: raid10 personality registered for level 10
[ 17.077885] md: raid6 personality registered for level 6
[ 17.083199] md: raid5 personality registered for level 5
[ 17.088518] md: raid4 personality registered for level 4
[ 17.094296] device-mapper: ioctl: 4.25.0-ioctl (2013-06-26) initialised: dm-d evel@redhat.com
[ 17.103115] sdhci: Secure Digital Host Controller Interface driver
[ 17.109301] sdhci: Copyright(c) Pierre Ossman
[ 17.113642] sdhci-pltfm: SDHCI platform and OF driver helper
[ 17.129782] ST_DDR CNTRL driver registered
[ 17.134256] st-lpm driver registered
[ 17.138238] TCP: cubic registered
[ 17.141542] NET: Registered protocol family 17
[ 17.146023] Key type dns_resolver registered
[ 17.150417] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 17.158079] Registering SWP/SWPB emulation handler
[ 17.163760] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 17.173153] Loading module verification blacklist certificates
[ 17.179037] Loading module verification certificates
[ 17.184049] MODSIGN: Loaded cert 'Synology SDG kernel module signing key: 7bd 0b0d6bcd31651c22ce3978bdc8c8bdc417329'
[ 17.199108] MODSIGN: Loaded cert 'Synology Root Certification Authority: f2c0 75361f168425f8b5ef31b796406c3aab2089'
[ 17.209496] MODSIGN: Loaded cert 'Synology Kernel Module Signing Certificatio n Authority: 600839b5d127e0e11d817a31f0575d323a7c0e28'
[ 17.221397] MODSIGN: Loaded cert 'Synology kernel module signing key: 4646ce5 4489669338118a3b1286da156ac366fa5'
[ 17.250847] MTT: registering output driver dfs
[ 17.255296] MTT: multicore-trace initialized.
[ 17.259719] vmmc0: disabling
[ 17.262591] regulator-dummy: disabling
[ 17.282596] Freeing unused kernel memory: 232K (80666000 - 806a0000)
START /linuxrc.syno
Insert basic USB modules...
:: Loading module phy-stih407-usb[ 17.394718] stih407-usb-genphy f8.usbpicophy : STiH407 USB Generic picoPHY driver probed!
[ 17.403226] stih407-usb-genphy fc.usbpicophy: STiH407 USB Generic picoPHY dri ver probed!
[ 17.411734] stih407-usb-genphy 100.usbpicophy: STiH407 USB Generic picoPHY dr iver probed!
... [ OK ]
:: Loading module phy-st-usb3[ 17.443191] sti-usb3-phy 8f90000.usb3_phy: USB3 MiPHY Ref clk 30 MHz enabled
[ 17.450329] sti-usb3-phy 8f90000.usb3_phy: usb3 ioaddr 0xac94e000, pipew ioad dr 0xac964000
[ 17.458681] sti-usb3-phy 8f90000.usb3_phy: USB3 MiPHY2 probed
... [ OK ]
:: Loading module usb-common ... [ OK ]
:: Loading module usbcore[ 17.522914] usbcore: registered new interface driver usbfs
[ 17.530398] usbcore: registered new interface driver hub
[ 17.542338] usbcore: registered new device driver usb
... [ OK ]
:: Loading module dwc3 ... [ OK ]
:: Loading module ehci-hcd[ 17.597623] ehci_hcd: USB 2.0 'Enhanced' Host Contr oller (EHCI) Driver
... [ OK ]
:: Loading module ehci-pci[ 17.621140] ehci-pci: EHCI PCI platform driver
... [ OK ]
:: Loading module ehci-platform[ 17.642613] ehci-platform: EHCI generic platfo rm driver
... [ OK ]
:: Loading module ohci-hcd[ 17.671214] ohci_hcd: USB 1.1 'Open' Host Controlle r (OHCI) Driver
... [ OK ]
:: Loading module xhci-hcd ... [ OK ]
:: Loading module st-hcd[ 17.748099] st-pinctrl 922f080.pin-controller-rear: m aps: function usb0 group usb2-0 num 3
[ 17.756415] st-hcd 9a03c00.usb: 48MHz ohci clk not found
[ 17.761875] stih407-usb-genphy f8.usbpicophy: Generic picoPHY usb port init.
[ 17.768944] stih407-usb-genphy f8.usbpicophy: found picoPHY in rst state
[ 17.776234] ehci-platform ehci-platform.0: EHCI Host Controller
[ 17.782166] ehci-platform ehci-platform.0: new USB bus registered, assigned b us number 1
[ 17.790643] ehci-platform ehci-platform.0: irq 183, io mem 0x09a03e00
[ 17.807946] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00, overcu rrent ignored
[ 17.816909] hub 1-0:1.0: USB hub found
[ 17.820715] hub 1-0:1.0: 1 port detected
[ 17.826868] ohci-platform ohci-platform.0: Generic Platform OHCI Controller
[ 17.833885] ohci-platform ohci-platform.0: new USB bus registered, assigned b us number 2
[ 17.842035] ohci-platform ohci-platform.0: irq 212, io mem 0x09a03c00
[ 17.912714] hub 2-0:1.0: USB hub found
[ 17.916476] hub 2-0:1.0: 1 port detected
... [ OK ]
:: Loading module dwc3-st[ 17.955689] st-pinctrl 922f080.pin-controller-rear: maps: function usb3 group usb3-2 num 3
[ 17.964130] usb-st-dwc3 8f94000.dwc3: glue-logic addr 0xac9fc000, syscfg-reg offset 0x110
[ 17.973363] dwc3 9900000.dwc3: unable to find phy
[ 17.978602] sti-usb3-phy 8f90000.usb3_phy: MiPHY28LP setup
[ 17.984085] sti-usb3-phy 8f90000.usb3_phy: MiPHY28LP release 0x231 found
[ 17.990988] sti-usb3-phy 8f90000.usb3_phy: USB3 MIPHY28LP timer initialized
[ 17.997956] stih407-usb-genphy 100.usbpicophy: Generic picoPHY usb port init.
[ 18.204950] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 18.210470] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus nu mber 3
[ 18.218794] xhci-hcd xhci-hcd.0.auto: irq 187, io mem 0x09900000
[ 18.225526] hub 3-0:1.0: USB hub found
[ 18.229369] hub 3-0:1.0: 1 port detected
[ 18.233444] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 18.238956] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus nu mber 4
[ 18.250707] hub 4-0:1.0: USB hub found
[ 18.254478] hub 4-0:1.0: 1 port detected
[ 18.258608] usb-st-dwc3 8f94000.dwc3: configured as host DRD
[ 18.264367] usb-st-dwc3 8f94000.dwc3: probe exits fine...
... [ OK ]
insmod: can't insert '/lib/modules/etxhci-hcd.ko': No such file or directory
Insert net driver(Mindspeed only)...
[ 18.331354] ds216play_synobios: module license 'Synology Inc.' taints kernel.
[ 18.339486] Disabling lock debugging due to kernel taint
[ 18.346968] synobios: load, major number 201
[ 18.351347] synobios cpu_arch proc entry initialized
[ 18.356302] synobios crypto_hw proc entry initialized
[ 18.361365] synobios syno_platform proc entry initialized
[ 18.366990] synobios open /dev/ttyS1 success
Starting /usr/syno/bin/synocfgen...
/usr/syno/bin/synocfgen returns 0
Exit on error [1] DISK NOT INSTALLED...
Thr Nov 5 00:12:30 UTC 2020
none /sys/kernel/debug debugfs rw,relatime 0 0
sys /sys sysfs rw,relatime 0 0
none /dev devtmpfs rw,relatime,size=326624k,nr_inodes=81656,mode=755 0 0
proc /proc proc rw,relatime 0 0
linuxrc.syno failed on 1
starting pid 1844, tty '': '/etc/rc'
:: Starting /etc/rc
:: Mounting procfs ... [ OK ]
:: Mounting tmpfs ... [ OK ]
:: Mounting devtmpfs ... [ OK ]
:: Mounting devpts ... [ OK ]
:: Mounting sysfs ... [ OK ]
mdadm: error opening /dev/md1: No such file or directory
rc: Use all internal disk as swap.
rc: No internal disk installed.
swapon: can't stat '/dev/md1': No such file or directory
:: Loading module fat ... [ OK ]
:: Loading module vfat ... [ OK ]
:: Loading module synobios[ 19.015538] synobios: load, major number 201
[ 19.019864] synobios cpu_arch proc entry initialized
[ 19.024818] synobios crypto_hw proc entry initialized
[ 19.029872] synobios syno_platform proc entry initialized
[ 19.035493] synobios open /dev/ttyS1 success
... [ OK ]
[ 19.223874] dwmac1000: Master AXI performs any burst length
udhcpc (v1.16.1) started
eth0 Link encap:Ethernet HWaddr 00:00:0B:2D:F5:7B
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:1 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:60 (60.0 B) TX bytes:0 (0.0 B)
Interrupt:130
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
:: Starting syslogd ... [ OK ]
/etc/rc: line 273: /usr/syno/bin/syno_pstore_collect: not found
:: Starting scemd
[ 24.208167] libphy: stmmac-0:01 - Link is Up - 100/Full
:: Starting services in background
Starting findhostd in flash_rd...
Starting services in flash_rd...
Running /usr/syno/etc/rc.d/J01httpd.sh...
Starting httpd:80 in flash_rd...
Starting httpd:5000 in flash_rd...
Running /usr/syno/etc/rc.d/J03ssdpd.sh...
/usr/bin/minissdpd -i eth0
(15): upnp:rootdevice
(51): uuid:upnp_SynologyNAS-00000b2df57b::upnp:rootdevice
(60): Synology/synology_monaco_ds216play/6.2-24922/169.254.231.220
(48): http://169.254.231.220:5000/description-eth0.xml
Connected.
done.
/usr/syno/bin/reg_ssdp_service 169.254.231.220 00000b2df57b 6.2-24922 synology_m onaco_ds216play eth0
Running /usr/syno/etc/rc.d/J04synoagentregisterd.sh...
Starting synoagentregisterd...
Running /usr/syno/etc/rc.d/J30DisableNCQ.sh...
cat: can't open '/sys/block/sd*/device//model': No such file or directory
Running /usr/syno/etc/rc.d/J80ADTFanControl.sh...
Running /usr/syno/etc/rc.d/J98nbnsd.sh...
Starting nbnsd...
Running /usr/syno/etc/rc.d/J99avahi.sh...
Starting Avahi mDNS/DNS-SD Daemon
cname_load_conf failed:/var/tmp/nginx/avahi-aliases.conf
:: Loading module usb-storage[ 27.512858] usbcore: registered new interface dr iver usb-storage
... [ OK ]
mknod: /dev/ubi_ctrl: File exists
============ Date ============
Thr Nov
Thu Nov 5 00:12:39 2020
6 RedBoot partitions found on MTD device n25q064 [ 22.278634] Creating 6 MTD partitions on "n25q064": [ 22.278639] 0x000000000000-0x0000000c0000 : "RedBoot" [ 22.284723] 0x0000000c0000-0x000000390000 : "zImage" [ 22.286362] 0x000000390000-0x0000007d0000 : "rd.gz" [ 22.288018] 0x0000007d0000-0x0000007e0000 : "vendor" [ 22.288041] vender Mac0 address : 00:11:32:74:xx:xx [ 22.288045] vender Mac1 doesn't set ucSum:0x00 Buf:0x00 Sum:0. [ 22.288047] vender Mac2 doesn't set ucSum:0x00 Buf:0x00 Sum:0. [ 22.288050] vender Mac3 doesn't set ucSum:0x00 Buf:0x00 Sum:0. [ 22.289703] serial number='1730NEN10xxxx' [ 22.289704] 0x0000007e0000-0x0000007f0000 : "RedBoot Config" [ 22.291332] 0x0000007f0000-0x000000800000 : "FIS directory"As mentioned, I tried to verify content of flash and it seems consistent. Does anyone have idea which way to go?
|
Re: DS216 play Redboot problem? April 21, 2021 12:09AM |
Admin Registered: 13 years ago Posts: 18,548 |
Quote
[ 0.000000] Linux version 3.10.105 (root@build9) (gcc version 4.9.3 20150311 (prerelease) (crosstool-NG 1.20.0) ) #24922 SMP Fri May 10 02:58:37 CST 2019
[ 0.000000] Machine: STi SoC with Flattened Device Tree, model: STiH410 B2120
Quote
correct logging when the kernel found the mtd partitions on flash
6 RedBoot partitions found on MTD device n25q064 [ 22.278634] Creating 6 MTD partitions on "n25q064": [ 22.278639] 0x000000000000-0x0000000c0000 : "RedBoot" [ 22.284723] 0x0000000c0000-0x000000390000 : "zImage" [ 22.286362] 0x000000390000-0x0000007d0000 : "rd.gz" [ 22.288018] 0x0000007d0000-0x0000007e0000 : "vendor" [ 22.288041] vender Mac0 address : 00:11:32:74:xx:xx [ 22.288045] vender Mac1 doesn't set ucSum:0x00 Buf:0x00 Sum:0. [ 22.288047] vender Mac2 doesn't set ucSum:0x00 Buf:0x00 Sum:0. [ 22.288050] vender Mac3 doesn't set ucSum:0x00 Buf:0x00 Sum:0. [ 22.289703] serial number='1730NEN10xxxx' [ 22.289704] 0x0000007e0000-0x0000007f0000 : "RedBoot Config" [ 22.291332] 0x0000007f0000-0x000000800000 : "FIS directory"
Quote
Booting using the fdt blob at 0x4f000000
Press Ctrl+C to abort autoboot in 3 second
printenv
|
Re: DS216 play Redboot problem? April 21, 2021 05:19PM |
Registered: 2 years ago Posts: 3 |
▒ U-Boot 2014.01-g982ae47-dirty (Aug 27 2015 - 18:57:06) - stm24-2014-09-25 Board: B2120-revc-STxH410 [ARM] I2C: ready DRAM: 1 GiB SPI: info: found ST N25Q064 (8MiB) device (page=256,erase=65536) *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Synology Model: DS216play Fan Status: Not Good Fan 1: Not Good Net: stmac-1 Warning: stmac-1 using MAC address from net device USB0: Register 2000240 NbrPorts 2 Starting the controller USB XHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found Transcoding memorylayout: 1 channel mode. Press Ctrl+C to abort autoboot in 3 second B2120> <INTERRUPT> B2120> printenv baudrate=115200 board=b2120 bootargs= bootcmd=run syno_bootargs; run spiboot bootdelay=10 ethact=stmac-1 ethaddr=00:11:32:71:xx:xx fdt_high=0xFFFFFFFF fdt_load_addr=0x4F000000 fdt_spi_addr=0x00060000 initrd_high=0x44000000 kernel_load_addr=0x43000000 kernel_spi_addr=0x000C0000 load_addr=0x40000000 rd_load_addr=0x44000000 rd_spi_addr=0x00390000 spiboot=eeprom read $fdt_load_addr $fdt_spi_addr 60000;eeprom read $rd_load_addr $rd_spi_addr 440000;eeprom read $kernel_load_addr $kernel_spi_addr 2D0000;bootm $kernel_load_addr $rd_load_addr $fdt_load_addr stderr=serial stdin=serial stdout=serial syno_boot_dev=/dev/md0 syno_bootargs=setenv bootargs "console=ttyS0,115200 CONSOLE=/dev/ttyS0 ip=off mt dparts=stm-nand-bch.0:0x500000(boot),-(rfs) bpa2parts=BPA2_Region|aud-coded|aud- transcoded|vid-coded|vid-transcoded|vid-raw-input|vid-output-0|vid-decimated-1|v id-copied-1|vid-macroblock-0|vid-extra-data-0|vid-extra-data-1|v4l2-coded-video- buffers|vid-enc-data-0|vid-enc-scaled-0|vid-encoded-0|v4l2-clut|v4l2-grab|gfx-me mory|aud-codec-data|vid-codec-data|aud-output-0|aud-output-1|vid-output-1|vid-de cimated-0|vid-copied-0|vid-macroblock-1|blitter|vid-enc-data-1|vid-enc-scaled-1| vid-encoded-1|coredisplay-video|multicom|hades-l3|BPA2_Region0|BPA2_Region1:240M :0x71000000,v4l2-vb2|v4l2-stmc8jpg|v4l2-stmvout|v4l2-compo:24M:0x6F800000,coproc s:32M:0x40000000,modules|audio:8M:0x6F000000,bigphysarea|te-buffers|m2m-ca3:32M: 0x48000000,STMCReserve:32768:0x47FF8000 vmalloc=535m mem=720m@0x42000000 root=$s yno_boot_dev rw $syno_extra_args syno_hw_version=$syno_hw_version hd_power_on_se q=$syno_hdd_powerup_seq ihd_num=$syno_hdd_powerup_seq netif_num=$syno_net_if_num flash_size=8 phys_memsize=$syno_phys_memsize" syno_mem_mode=1 syno_extra_args= syno_hdd_powerup_seq=2 syno_hw_version=DS216play syno_net_if_num=1 syno_phys_memsize=1024 Environment size: 1885/16380 bytes B2120>I deleted here the mac adress.
|
Re: DS216 play Redboot problem? April 21, 2021 05:41PM |
Admin Registered: 13 years ago Posts: 18,548 |
bootcmd=run syno_bootargs; run spiboot spiboot=eeprom read $fdt_load_addr $fdt_spi_addr 60000; eeprom read $rd_load_addr $rd_spi_addr 440000;eeprom read $kernel_load_addr $kernel_spi_addr 2D0000;bootm $kernel_load_addr $rd_load_addr $fdt_load_addr
syno_bootargs=setenv bootargs "console=ttyS0,115200 CONSOLE=/dev/ttyS0 ip=off mtdparts=stm-nand-bch.0:0x500000(boot),-(rfs)
fdt_spi_addr=0x00060000
|
Re: DS216 play Redboot problem? April 22, 2021 04:20PM |
Registered: 2 years ago Posts: 3 |
0x000000000000-0x0000000c0000 : "RedBoot" [ 22.284723] 0x0000000c0000-0x000000390000 : "zImage" [ 22.286362] 0x000000390000-0x0000007d0000 : "rd.gz" [ 22.288018] 0x0000007d0000-0x0000007e0000 : "vendor" [ 22.288041] vender Mac0 address : 00:11:32:74:xx:xx [ 22.288045] vender Mac1 doesn't set ucSum:0x00 Buf:0x00 Sum:0. [ 22.288047] vender Mac2 doesn't set ucSum:0x00 Buf:0x00 Sum:0. [ 22.288050] vender Mac3 doesn't set ucSum:0x00 Buf:0x00 Sum:0. [ 22.289703] serial number='1730NEN10xxxx' [ 22.289704] 0x0000007e0000-0x0000007f0000 : "RedBoot Config" [ 22.291332] 0x0000007f0000-0x000000800000 : "FIS directory"I can create different layout myself from available info, u-boot, zimage, ramdisk, vender partition I can create also.
|
Re: DS216 play Redboot problem? April 22, 2021 07:53PM |
Admin Registered: 13 years ago Posts: 18,548 |