Welcome! Log In Create A New Profile

Advanced

PogoPlug V4 won't boot after failed env input

Posted by devinger 
Forum List Message List New Topic
devinger
PogoPlug V4 won't boot after failed env input
October 20, 2014 10:12AM
Hello everyone,

I was trying to do a reinstall of arch on my pogoplug when the power in the part of the house where the pogolpug was connected went down. My pogo didn't start correctly so I soldered a serial cable. I can see what is happening via putty. Could somebody please help me to get the pogoplug working again? I am not a very experienced user.

This is the installation log, in-till power went down: 
login as: root
root@192.168.178.17's password:
~ # killall hbwd
~ # cd /tmp
/tmp # wget http://download.doozan.com/uboot/nanddump
Connecting to download.doozan.com (50.116.34.13:80)
/tmp # wget http://download.doozan.com/uboot/nandwrite
Connecting to download.doozan.com (50.116.34.13:80)
/tmp # wget http://download.doozan.com/uboot/flash_erase
Connecting to download.doozan.com (50.116.34.13:80)
/tmp # wget http://download.doozan.com/uboot/fw_printenv
Connecting to download.doozan.com (50.116.34.13:80)
/tmp # chmod +x flash_erase fw_printenv nanddump nandwrite
/tmp # cp fw_printenv fw_setenv
/tmp # mount -o remount,rw /
/tmp # echo "/dev/mtd0 0xc0000 0x20000 0x20000">/etc/fw_env.config
/tmp # wget http://download.qnology.com/pogoplug/v4/uboot.2014.07-tld-1.pogo_v4.
bodhi.tar
Connecting to download.qnology.com (162.252.240.221:80)
/tmp # wget http://download.qnology.com/pogoplug/v4/uboot.2014.07-tld-1.pogo_v4.
bodhi.md5
Connecting to download.qnology.com (162.252.240.221:80)
/tmp # md5sum uboot.2014.07-tld-1.pogo_v4.bodhi.tar
d4b497dc5239844fd2d45f4ca83132e0  uboot.2014.07-tld-1.pogo_v4.bodhi.tar
/tmp # cat uboot.2014.07-tld-1.pogo_v4.bodhi.md5
d4b497dc5239844fd2d45f4ca83132e0

/tmp #
/tmp # tar -xf uboot.2014.07-tld-1.pogo_v4.bodhi.tar
/tmp # /tmp/flash_erase /dev/mtd0 0 4
Erase Total 4 Units
Performing Flash Erase of length 131072 at offset 0x60000 done
/tmp # /tmp/nandwrite /dev/mtd0 /tmp/uboot.2014.07-tld-1.pogo_v4.mtd0.kwb
Writing data to block 0 at offset 0x0
Writing data to block 1 at offset 0x20000
Writing data to block 2 at offset 0x40000
Writing data to block 3 at offset 0x60000
/tmp #
/tmp # wget http://download.qnology.com/pogoplug/v4/uboot.2014.07-tld-1.environm
ent.img.bodhi.tar
Connecting to download.qnology.com (162.252.240.221:80)
/tmp # wget http://download.qnology.com/pogoplug/v4/uboot.2014.07-tld-1.environm
ent.img.bodhi.md5
Connecting to download.qnology.com (162.252.240.221:80)
/tmp # d5sum uboot.2014.07-tld-1.environment.img.bodhi.tar
-sh: d5sum: not found
/tmp # cat uboot.2014.07-tld-1.environment.img.bodhi.md5
c5921e3ea0a07a859878339ffb771088

/tmp # tar -xf uboot.2014.07-tld-1.environment.img.bodhi.tar
/tmp # /tmp/flash_erase /dev/mtd0 0xc0000 1
Erase Total 1 Units
Performing Flash Erase of length 131072 at offset 0xc0000 done
/tmp # /tmp/nandwrite -s 786432 /dev/mtd0 uboot.2014.07-tld-1.environment.img
Writing data to block 6 at offset 0xc0000
/tmp #
/tmp # /tmp/fw_setenv ethaddr "$(cat /sys/class/net/eth0/address)"
Cannot parse config file: Invalid argument
/tmp # /tmp/fw_printenv ethaddr
Cannot parse config file: Invalid argument
/tmp # /tmp/fw_setenv ethaddr "$(cat /sys/class/net/eth0/address)"
Cannot parse config file: Invalid argument
/tmp # /tmp/fw_setenv ethaddr "$(cat /sys/class/net/eth0/address)"
Cannot parse config file: Invalid argument
/tmp # /tmp/fw_printenv ethaddr
Cannot parse config file: Invalid argument
/tmp # /tmp/fw_setenv arcNumber 3960
Cannot parse config file: Invalid argument
/tmp # /tmp/fw_setenv machid F78
Cannot parse config file: Invalid argument
/tmp # /tmp/flash_erase /dev/mtd0 0xc0000 1
Erase Total 1 Units
Performing Flash Erase of length 131072 at offset 0xc0000 done
/tmp # /tmp/nandwrite -s 786432 /dev/mtd0 uboot.2014.07-tld-1.environment.img
Writing data to block 6 at offset 0xc0000
/tmp #
/tmp # /tmp/fw_setenv ethaddr "$(cat /sys/class/net/eth0/address)"
Cannot parse config file: Invalid argument
/tmp # /tmp/fw_setenv usb_rootfstype ext3
Cannot parse config file: Invalid argument
/tmp # reboot
-sh: reboot: not found
/tmp # /
-sh: /: Permission denied
/tmp #
/tmp # #SET MACADDRESS
/tmp # /tmp/fw_setenv ethaddr "$(cat /sys/class/net/eth0/address)"
Cannot parse config file: Invalid argument
/tmp # /tmp/fw_setenv ethaddr "$(cat /sys/class/net/eth0/address)"
Cannot parse config file: Invalid argument
/tmp # /tmp/fw_printenv ethaddr
Cannot parse config file: Invalid argument
/tmp # /tmp/fw_setenv arcNumber 3960
Cannot parse config file: Invalid argument
/tmp # /tmp/fw_setenv machid F78.
Cannot parse config file: Invalid argument
/tmp # wget http://download.qnology.com/pogoplug/v4/uboot.2014.07-tld-1.environm
ent.img.bodhi.tar
Connecting to download.qnology.com (162.252.240.221:80)
wget: can't open 'uboot.2014.07-tld-1.environment.img.bodhi.tar': File exists
/tmp # wget http://download.qnology.com/pogoplug/v4/uboot.2014.07-tld-1.environm
ent.img.bodhi.md5
Connecting to download.qnology.com (162.252.240.221:80)
wget: can't open 'uboot.2014.07-tld-1.environment.img.bodhi.md5': File exists
/tmp # md5sum uboot.2014.07-tld-1.environment.img.bodhi.tar
c5921e3ea0a07a859878339ffb771088  uboot.2014.07-tld-1.environment.img.bodhi.tar
/tmp # cat uboot.2014.07-tld-1.environment.img.bodhi.md5
c5921e3ea0a07a859878339ffb771088

/tmp # tar -xf uboot.2014.07-tld-1.environment.img.bodhi.tar
/tmp # /tmp/flash_erase /dev/mtd0 0xc0000 1
Erase Total 1 Units
Performing Flash Erase of length 131072 at offset 0xc0000 done
/tmp # /tmp/nandwrite -s 786432 /dev/mtd0 uboot.2014.07-tld-1.environment.img
Writing data to block 6 at offset 0xc0000
/tmp #
/tmp # /tmp/fw_setenv ethaddr "$(cat /sys/class/net/eth0/address)"
Cannot parse config file: Invalid argument

This is what is happening when de device boots: 
U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45)
Pogoplug V4

SoC:   Kirkwood 88F6192_A1
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  128 MiB
MMC:   kwsdio: 0
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Warning: failed to set MAC address

Hit any key to stop autoboot:  0
Pogov4> printenv
arcNumber=2097
baudrate=115200
bootargs=root=ubi0:rootfs ubi.mtd=2,512 rootfstype=ubifs console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x25,0x31,0x00,0xd4,0x6f mem=128 poweroutage=yes
bootcmd=run boot_nand
bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot
bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot;
bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot;
bootdelay=10
console=ttyS0,115200
device=0:1
ethact=egiga0
if_netconsole=ping $serverip
ipaddr=192.168.0.231
led_error=orange blinking
led_exit=green off
led_init=green blinking
machid=0x831
mainlineLinux=yes
mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
mmc_init=mmc rescan
mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage
mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd
mmc_root=/dev/mmcblk0p1
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
partition=nand0,2
preboot_nc=run if_netconsole start_netconsole
rootdelay=10
rootfstype=ext3
sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
sata_init=ide reset
sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage
sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd
sata_root=/dev/sda1
serverip=192.168.0.220
set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
usb_init=usb start
usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage
usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd
usb_root=/dev/sda1

Environment size: 2304/131068 bytes

As you can see it loads Uboot, but doesn't set a mac adress. I really hope somebody can help me with this.



Edited 1 time(s). Last edit at 10/20/2014 10:14AM by devinger.
Reply Quote
bodhi
Re: PogoPlug V4 won't boot after failed env input
October 21, 2014 12:13AM
devinger,

When you see the u-boot banner, and the countdown: 

> U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45)
> Pogoplug V4
> 
> SoC:   Kirkwood 88F6192_A1
> DRAM:  128 MiB
> WARNING: Caches not enabled
> NAND:  128 MiB
> MMC:   kwsdio: 0
> In:    serial
> Out:   serial
> Err:   serial
> Net:   egiga0
> Warning: failed to set MAC address
> 
> Hit any key to stop autoboot:  0

Interrupt u-boot, and set the envs (ethaddr is your MAC address) 
Pogov4> setenv arcNumber 3960
Pogov4> setenv machid f78
Pogov4> setenv ethaddr xx:xx:xx:xx:xx

then 

Pogov4> boot

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)



Edited 1 time(s). Last edit at 10/21/2014 12:13AM by bodhi.
Reply Quote
devinger
Re: PogoPlug V4 won't boot after failed env input
October 21, 2014 01:54PM
Thanks for the reply. I tried it but got the following: 
Pogov4> setenv arcNumber 3960
Pogov4> setenv machid f78
Pogov4> setenv ethaddr 00:25:31:04:ED:6A
Pogov4> boot
## Error: "boot_nand" not defined



Edited 1 time(s). Last edit at 10/21/2014 01:55PM by devinger.
Reply Quote
bodhi
Re: PogoPlug V4 won't boot after failed env input
October 21, 2014 04:32PM
Looks like the bootcmd is also bad, should reset it to:

setenv bootcmd 'run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; reset'

And then

boot

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Reply Quote
devinger
Re: PogoPlug V4 won't boot after failed env input
October 21, 2014 06:33PM
Thanks for the reply.

Did it, unfortunately nothing really happend :( The green light is blinking but thats it. 

Pogov4> setenv arcNumber 3960
Pogov4> setenv machid f78
Pogov4> setenv ethaddr 00:25:31:04:ED:6A
Pogov4> setenv bootcmd 'run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; reset
> boot
>

I do really appreciate you your help so far! :)
Reply Quote
grayman4hire
Re: PogoPlug V4 won't boot after failed env input
October 21, 2014 08:30PM
Hi @devinger,

Sorry to hear you're having issues with hacking your Pogoplug. I'm the author of the tutorial and trying to figure out what went wrong with your setup.

@bodhi/anyone see anything obvious that would cause the "Cannot parse config file: Invalid argument"? 

/tmp # /tmp/fw_setenv ethaddr "$(cat /sys/class/net/eth0/address)"
Cannot parse config file: Invalid argument

I assume the "config file" the error is referring to is the /etc/fw_env.config generated by the following echo command: 

#setup fw_env.config
echo "/dev/mtd0 0xc0000 0x20000 0x20000">/etc/fw_env.config

@devinger, was your Pogoplug new? Is the installation log your provided complete and accurate? Anything else you can add that might help explain what may have happened?

Really odd that you're also missing or have incorrect environment variables.
Reply Quote
devinger
Re: PogoPlug V4 won't boot after failed env input
October 21, 2014 09:27PM
Great that you want to help!
I used your tutorial before and it worked with the same pogoplug :) after connecting my hdd caused the pogoplug to crash with arch I tried to reinstall the software. I did it once before (reinstalling everything) and it all went fine. The log is from when I restarted the pogo on the pogo os without a usb stick (it booted correctly thanks to your tutorial :) ) and did a reinstall. I just copy d everything and started to look for a solution on which the first step was soldering the cable
Reply Quote
grayman4hire
Re: PogoPlug V4 won't boot after failed env input
October 21, 2014 09:54PM
That doesn't really explain why you bootcmd is set wrong. The default uboot environment parameter image should have set it correctly.

"bootcmd=run boot_nand" should be "bootcmd=run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; reset"

See @bluechalk's post for the correct default uboot parameters - http://forum.doozan.com/read.php?3,18024

At any rate, let's move on and get you working. This should be an easy fix.

Theoretically, you should be able to apply the default uBoot Environment Parameters and then update the env parameters appropriately. Run the following from the Pogoplug OS and post the output/results. 

#stop my.pogoplug.com service
killall hbwd

#download firmware utilities
cd /tmp
wget http://download.doozan.com/uboot/nanddump
wget http://download.doozan.com/uboot/nandwrite
wget http://download.doozan.com/uboot/flash_erase
wget http://download.doozan.com/uboot/fw_printenv

#make executable
chmod +x flash_erase fw_printenv nanddump nandwrite

#printenv and setenv are normally symbolic links
cp fw_printenv fw_setenv

#remount '/' as read/write
#by default the Pogoplug OS (internal flash) is read only
#skip if running from Debian/ALARM
mount -o remount,rw /

#setup fw_env.config
echo "/dev/mtd0 0xc0000 0x20000 0x20000">/etc/fw_env.config

#output current uboot environment parameters
/tmp/fw_printenv

#Download and Flash uBoot Environment Parameters

#download default uboot env settings and md5
wget http://download.qnology.com/pogoplug/v4/uboot.2014.07-tld-1.environment.img.bodhi.tar
wget http://download.qnology.com/pogoplug/v4/uboot.2014.07-tld-1.environment.img.bodhi.md5

#check md5 sum (output should match)
md5sum uboot.2014.07-tld-1.environment.img.bodhi.tar
cat uboot.2014.07-tld-1.environment.img.bodhi.md5

#extract uboot env settings
tar -xf uboot.2014.07-tld-1.environment.img.bodhi.tar

#flash default uboot env setting
#BE EXTRA CAREFUL WITH THE NEXT TWO COMMANDS. NO TYPOS!
/tmp/flash_erase /dev/mtd0 0xc0000 1
/tmp/nandwrite -s 786432 /dev/mtd0 uboot.2014.07-tld-1.environment.img

#output current uboot parameters after applying default
/tmp/fw_printenv

#Update uBoot Environment Parameters

#SET MACADDRESS
/tmp/fw_setenv ethaddr "$(cat /sys/class/net/eth0/address)"

#double check the MAC Address matches with 
#what is on the bottom of your Pogoplug
/tmp/fw_printenv ethaddr

#set archNumber and machid (for LED)
/tmp/fw_setenv arcNumber 3960
/tmp/fw_setenv machid F78

#set rootfs file system type
/tmp/fw_setenv usb_rootfstype ext3

#set to original mtd partition layout
/tmp/fw_setenv mtdparts 'mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)'

#print out all uboot environment parameters
#make sure there are no errors
/tmp/fw_printenv
Reply Quote
bodhi
Re: PogoPlug V4 won't boot after failed env input
October 22, 2014 12:47AM
@devinger ,

Try: 
Pogov4> setenv arcNumber 3960
Pogov4> setenv machid f78
Pogov4> setenv ethaddr 00:25:31:04:ED:6A
Pogov4> setenv bootcmd 'run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; reset'
Pogov4> run bootcmd

And post the log of what happen after that here!

@grayman,

re: 
Cannot parse config file: Invalid argument
Hard to say without knowing what devinger's Pogo enviroment looks like at that time.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Reply Quote
devinger
Re: PogoPlug V4 won't boot after failed env input
October 22, 2014 07:12AM
I have a big smile on my face right now!

I tried bodhi his awnser first and this is what happend: 

U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45)
Pogoplug V4

SoC:   Kirkwood 88F6192_A1
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  128 MiB
MMC:   kwsdio: 0
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Warning: failed to set MAC address

Hit any key to stop autoboot:  0
Pogov4> setenv arcNumber 3960
Pogov4> setenv machid f78
Pogov4> setenv ethaddr 00:25:31:04:ED:6A
Pogov4> setenv bootcmd 'run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; rese                                                                             t'
Pogov4> run bootcmd
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
3927160 bytes read in 285 ms (13.1 MiB/s)
** File not found /boot/uInitrd **
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-3.16.2-1-ARCH
   Created:      2014-09-06   8:40:50 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3927096 Bytes = 3.7 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
Using machid 0xf78 from environment

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.16.2-1-ARCH (nobody@root-armv5-copy) (gcc version                                                                              4.8.2 20131219 (prerelease) (GCC) ) #1 PREEMPT Sat Sep 6 02:40:37 MDT 2014
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397                                                                             f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: Pogoplug V4
[    0.000000] Memory policy: Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pag                                                                             es: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdela                                                                             y=10 rootfstype=ext3 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(dat                                                                             a)
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] allocated 262144 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memor                                                                             y cgroups
[    0.000000] Memory: 121184K/131072K available (5466K kernel code, 340K rwdata                                                                             , 1668K rodata, 256K init, 697K bss, 9888K reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xffe00000   (2048 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff000000   ( 872 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06ffb24   (7135 kB)
[    0.000000]       .init : 0xc0700000 - 0xc074012c   ( 257 kB)
[    0.000000]       .data : 0xc0742000 - 0xc07973bc   ( 341 kB)
[    0.000000]        .bss : 0xc07973bc - 0xc08459a8   ( 698 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:114
[    0.000019] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 25769                                                                             803770ns
[    0.990289] Console: colour dummy device 80x30
[    0.990326] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216)
[    1.080114] pid_max: default: 32768 minimum: 301
[    1.080251] Security Framework initialized
[    1.080350] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    1.080378] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    1.081550] Initializing cgroup subsys memory
[    1.081767] Initializing cgroup subsys devices
[    1.081842] Initializing cgroup subsys freezer
[    1.081881] Initializing cgroup subsys net_cls
[    1.081929] Initializing cgroup subsys blkio
[    1.081976] Initializing cgroup subsys bfqio
[    1.082042] Initializing cgroup subsys perf_event
[    1.082076] Initializing cgroup subsys net_prio
[    1.082246] CPU: Testing write buffer coherency: ok
[    1.082904] Setting up static identity map for 0x532bc0 - 0x532c18
[    1.086054] devtmpfs: initialized
[    1.091354] pinctrl core: initialized pinctrl subsystem
[    1.091989] NET: Registered protocol family 16
[    1.092720] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    1.094380] cpuidle: using governor ladder
[    1.094423] cpuidle: using governor menu
[    1.094644] Kirkwood: MV88F6281-A1, TCLK=166666667.
[    1.094677] Feroceon L2: Enabling L2
[    1.094729] Feroceon L2: Cache support initialised.
[    1.097930] Kirkwood PCIe port 0: link up
[    1.097945] PCI: bus0 uses PCIe port 0
[    1.098274] PCI host bridge to bus 0000:00
[    1.098302] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[    1.098320] pci_bus 0000:00: root bus resource [io  0x1000-0xffff]
[    1.098337] pci_bus 0000:00: No busn resource found for root bus, will use [b                                                                             us 00-ff]
[    1.099489] PCI: bus0: Fast back to back transfers disabled
[    1.099567] pci 0000:00:01.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff 64bi                                                                             t]
[    1.099600] pci 0000:00:01.0: BAR 2: assigned [mem 0xe0010000-0xe0010fff 64bi                                                                             t]
[    1.099631] pci 0000:00:01.0: BAR 4: assigned [mem 0xe0011000-0xe0011fff 64bi                                                                             t]
[    1.132491] vgaarb: loaded
[    1.132994] SCSI subsystem initialized
[    1.133736] usbcore: registered new interface driver usbfs
[    1.133856] usbcore: registered new interface driver hub
[    1.134027] usbcore: registered new device driver usb
[    1.134270] pps_core: LinuxPPS API ver. 1 registered
[    1.134283] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome                                                                             tti <giometti@linux.it>
[    1.134332] PTP clock support registered
[    1.135861] Switched to clocksource orion_clocksource
[    1.163097] FS-Cache: Loaded
[    1.181947] NET: Registered protocol family 2
[    1.183303] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    1.183340] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    1.183369] TCP: Hash tables configured (established 1024 bind 1024)
[    1.183468] TCP: reno registered
[    1.183485] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    1.183516] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    1.183788] NET: Registered protocol family 1
[    1.183895] pci 0000:00:01.0: enabling device (0140 -> 0142)
[    1.186527] futex hash table entries: 256 (order: -1, 3072 bytes)
[    1.204251] VFS: Disk quotas dquot_6.5.2
[    1.204651] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.207487] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    1.209348] fuse init (API version 7.23)
[    1.211959] aufs 3.16-20140825
[    1.212007] msgmni has been set to 236
[    1.214612] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2                                                                             50)
[    1.214643] io scheduler noop registered
[    1.214663] io scheduler deadline registered
[    1.215285] io scheduler cfq registered
[    1.215361] io scheduler bfq registered (default)
[    1.215372] BFQ I/O-scheduler version: v7r5
[    1.215687] mv_xor mv_xor.0: Marvell shared XOR driver
[    1.256023] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[    1.295992] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[    1.296283] mv_xor mv_xor.1: Marvell shared XOR driver
[    1.335974] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[    1.375970] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[    1.383805] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    1.385345] console [ttyS0] disabled
[    1.405432] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 104                                                                             16666) is a 16550A
[    1.987478] console [ttyS0] enabled
[    2.004742] brd: module loaded
[    2.014511] loop: module loaded
[    2.018259] sata_mv sata_mv.0: cannot get optional clkdev
[    2.023717] sata_mv sata_mv.0: slots 32 ports 1
[    2.030709] scsi0 : sata_mv
[    2.034366] ata1: SATA max UDMA/133 irq 21
[    2.039990] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[    2.046511] nand: Hynix H27U1G8F2BTR-BC
[    2.050334] nand: 128MiB, SLC, page size: 2048, OOB size: 64
[    2.056005] Scanning device for bad blocks
[    2.144017] 4 cmdlinepart partitions found on MTD device orion_nand
[    2.150281] Creating 4 MTD partitions on "orion_nand":
[    2.155403] 0x000000000000-0x000000100000 : "u-boot"
[    2.161043] 0x000000100000-0x000000500000 : "uImage"
[    2.166599] 0x000000500000-0x000002500000 : "rootfs"
[    2.172168] 0x000002500000-0x000008000000 : "data"
[    2.186848] libphy: orion_mdio_bus: probed
[    2.191077] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    2.395901] ata1: SATA link down (SStatus 0 SControl F300)
[    3.280104] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address                                                                              00:00:00:00:00:00
[    3.289012] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.295520] ehci-pci: EHCI PCI platform driver
[    3.300082] ehci-orion: EHCI orion driver
[    3.304174] orion-ehci orion-ehci.0: EHCI Host Controller
[    3.309614] orion-ehci orion-ehci.0: new USB bus registered, assigned bus num                                                                             ber 1
[    3.317345] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[    3.335913] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[    3.343127] hub 1-0:1.0: USB hub found
[    3.347004] hub 1-0:1.0: 1 port detected
[    3.351808] xhci_hcd 0000:00:01.0: xHCI Host Controller
[    3.357114] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus numbe                                                                             r 2
[    3.367050] hub 2-0:1.0: USB hub found
[    3.370838] hub 2-0:1.0: 2 ports detected
[    3.375679] xhci_hcd 0000:00:01.0: xHCI Host Controller
[    3.380969] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus numbe                                                                             r 3
[    3.389684] hub 3-0:1.0: USB hub found
[    3.393466] hub 3-0:1.0: 2 ports detected
[    3.398805] usbcore: registered new interface driver usb-storage
[    3.405391] mousedev: PS/2 mouse device common for all mice
[    3.665935] usb 1-1: new high-speed USB device number 2 using orion-ehci
[    3.817955] usb-storage 1-1:1.0: USB Mass Storage device detected
[    3.824463] scsi1 : usb-storage 1-1:1.0
[    4.415905] rtc-mv rtc-mv: internal RTC not ticking
[    4.420980] i2c /dev entries driver
[    4.425382] sdhci: Secure Digital Host Controller Interface driver
[    4.431575] sdhci: Copyright(c) Pierre Ossman
[    4.436039] mvsdio mvsdio: no pins associated
[    4.476013] sdhci-pltfm: SDHCI platform and OF driver helper
[    4.485558] ledtrig-cpu: registered to indicate activity on CPUs
[    4.491834] usbcore: registered new interface driver r8712u
[    4.497727] gre: GRE over IPv4 demultiplexor driver
[    4.502667] TCP: cubic registered
[    4.506122] NET: Registered protocol family 17
[    4.510770] Key type dns_resolver registered
[    4.517438] registered taskstats version 1
[    4.523552] console [netcon0] enabled
[    4.527297] netconsole: network logging started
[    4.532486] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[    4.539672] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    4.547500] Waiting 10 sec before mounting root device...
[    4.826883] scsi 1:0:0:0: Direct-Access     SanDisk  Cruzer Fit       1.27 PQ                                                                             : 0 ANSI: 6
[    4.836778] sd 1:0:0:0: Attached scsi generic sg0 type 0
[    4.842293] sd 1:0:0:0: [sda] 15633408 512-byte logical blocks: (8.00 GB/7.45                                                                              GiB)
[    4.851520] sd 1:0:0:0: [sda] Write Protect is off
[    4.857144] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doe                                                                             sn't support DPO or FUA
[    4.872258]  sda: sda1
[    4.878271] sd 1:0:0:0: [sda] Attached SCSI removable disk
[   14.557413] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsyste                                                                             m
[   15.372007] EXT4-fs (sda1): recovery complete
[   15.406162] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts:                                                                              (null)
[   15.413864] VFS: Mounted root (ext3 filesystem) on device 8:1.
[   15.425595] devtmpfs: mounted
[   15.429845] Freeing unused kernel memory: 256K (c0700000 - c0740000)
[   15.693506] random: systemd urandom read with 44 bits of entropy available
[   15.725504] systemd[1]: systemd 216 running in system mode. (+PAM -AUDIT -SEL                                                                             INUX -IMA -APPARMOR +SMACK -SYSVINIT +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ                                                                             4 +SECCOMP +BLKID -ELFUTILS +KMOD -IDN )
[   15.743564] systemd[1]: Detected architecture 'arm'.

Welcome to Arch Linux ARM!

[   15.889971] NET: Registered protocol family 10
[   15.896045] systemd[1]: Inserted module 'ipv6'
[   15.908909] systemd[1]: Set hostname to <alarm>.
[   16.572677] systemd[1]: Cannot add dependency job for unit display-manager.se                                                                             rvice, ignoring: Unit display-manager.service failed to load: No such file or di                                                                             rectory.
[   16.594350] systemd[1]: Expecting device dev-ttyS0.device...
         Expecting device dev-ttyS0.device...
[   16.616172] systemd[1]: Starting Forward Password Requests to Wall Directory                                                                              Watch.
[   16.624437] systemd[1]: Started Forward Password Requests to Wall Directory W                                                                             atch.
[   16.632274] systemd[1]: Starting Remote File Systems.
[  OK  ] Reached target Remote File Systems.
[   16.656072] systemd[1]: Reached target Remote File Systems.
[   16.661889] systemd[1]: Starting Dispatch Password Requests to Console Direct                                                                             ory Watch.
[   16.670346] systemd[1]: Started Dispatch Password Requests to Console Directo                                                                             ry Watch.
[   16.678471] systemd[1]: Starting Paths.
[  OK  ] Reached target Paths.
[   16.696076] systemd[1]: Reached target Paths.
[   16.700731] systemd[1]: Starting Arbitrary Executable File Formats File Syste                                                                             m Automount Point.
[  OK  ] Set up automount Arbitrary Executab...ats File System Automount Point.
[   16.736099] systemd[1]: Set up automount Arbitrary Executable File Formats Fi                                                                             le System Automount Point.
[   16.745705] systemd[1]: Starting Encrypted Volumes.
[  OK  ] Reached target Encrypted Volumes.
[   16.766069] systemd[1]: Reached target Encrypted Volumes.
[   16.771626] systemd[1]: Starting Swap.
[  OK  ] Reached target Swap.
[   16.796059] systemd[1]: Reached target Swap.
[   16.800497] systemd[1]: Starting Root Slice.
[  OK  ] Created slice Root Slice.
[   16.876122] systemd[1]: Created slice Root Slice.
[   16.881043] systemd[1]: Starting User and Session Slice.
[  OK  ] Created slice User and Session Slice.
[   16.906101] systemd[1]: Created slice User and Session Slice.
[   16.912044] systemd[1]: Starting Device-mapper event daemon FIFOs.
[  OK  ] Listening on Device-mapper event daemon FIFOs.
[   16.936074] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[   16.942764] systemd[1]: Starting Delayed Shutdown Socket.
[  OK  ] Listening on Delayed Shutdown Socket.
[   16.966079] systemd[1]: Listening on Delayed Shutdown Socket.
[   16.971994] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[  OK  ] Listening on /dev/initctl Compatibility Named Pipe.
[   16.996081] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[   17.003210] systemd[1]: Starting Journal Socket (/dev/log).
[  OK  ] Listening on Journal Socket (/dev/log).
[   17.026080] systemd[1]: Listening on Journal Socket (/dev/log).
[   17.032172] systemd[1]: Starting LVM2 metadata daemon socket.
[  OK  ] Listening on LVM2 metadata daemon socket.
[   17.056080] systemd[1]: Listening on LVM2 metadata daemon socket.
[   17.062395] systemd[1]: Starting udev Control Socket.
[  OK  ] Listening on udev Control Socket.
[   17.086084] systemd[1]: Listening on udev Control Socket.
[   17.091701] systemd[1]: Starting udev Kernel Socket.
[  OK  ] Listening on udev Kernel Socket.
[   17.116081] systemd[1]: Listening on udev Kernel Socket.
[   17.121604] systemd[1]: Starting Journal Socket.
[  OK  ] Listening on Journal Socket.
[   17.146080] systemd[1]: Listening on Journal Socket.
[   17.151356] systemd[1]: Starting System Slice.
[  OK  ] Created slice System Slice.
[   17.176103] systemd[1]: Created slice System Slice.
[   17.181223] systemd[1]: Starting system-getty.slice.
[  OK  ] Created slice system-getty.slice.
[   17.206103] systemd[1]: Created slice system-getty.slice.
[   17.211682] systemd[1]: Starting system-serial\x2dgetty.slice.
[  OK  ] Created slice system-serial\x2dgetty.slice.
[   17.236099] systemd[1]: Created slice system-serial\x2dgetty.slice.
[   17.243144] systemd[1]: Mounting Debug File System...
         Mounting Debug File System...
[   17.276753] systemd[1]: Started Load Kernel Modules.
[   17.282029] systemd[1]: Starting Apply Kernel Variables...
         Starting Apply Kernel Variables...
[   17.311868] systemd[1]: Mounting FUSE Control File System...
         Mounting FUSE Control File System...
[   17.342725] systemd[1]: Mounting POSIX Message Queue File System...
         Mounting POSIX Message Queue File System...
[   17.381730] systemd[1]: Starting Setup Virtual Console...
         Starting Setup Virtual Console...
[   17.436613] systemd[1]: Starting udev Coldplug all Devices...
         Starting udev Coldplug all Devices...
[   17.471744] systemd[1]: Mounted Huge Pages File System.
[   17.489404] systemd[1]: Started Set Up Additional Binary Formats.
[   17.496566] systemd[1]: Starting Create list of required static device nodes                                                                              for the current kernel...
         Starting Create list of required st... nodes for the current kernel...
[   17.534099] systemd[1]: Mounted Configuration File System.
[   17.552593] systemd[1]: Starting Journal Service...
         Starting Journal Service...
[  OK  ] Started Journal Service.
[   17.606414] systemd[1]: Started Journal Service.
[  OK  ] Reached target Slices.
         Starting Remount Root and Kernel File Systems...
         Mounting Temporary Directory...
[  OK  ] Mounted POSIX Message Queue File System.
[  OK  ] Mounted Debug File System.
[  OK  ] Mounted FUSE Control File System.
[  OK  ] Mounted Temporary Directory.
[  OK  ] Started Apply Kernel Variables.
[  OK  ] Started Setup Virtual Console.
[  OK  ] Started Create list of required sta...ce nodes for the current kernel.
[  OK  ] Started Remount Root and Kernel File Systems.
[  OK  ] Started udev Coldplug all Devices.
         Starting Load/Save Random Seed...
         Starting Create Static Device Nodes in /dev...
[  OK  ] Started Load/Save Random Seed.
[  OK  ] Started Create Static Device Nodes in /dev.
         Starting udev Kernel Device Manager...
[  OK  ] Reached target Local File Systems (Pre).
[  OK  ] Reached target Local File Systems.
         Starting Trigger Flushing of Journal to Persistent Storage...
[   18.990684] systemd-udevd[90]: starting version 216
         Starting Create Volatile Files and Directories...
[  OK  ] Started udev Kernel Device Manager.
[  OK  ] Started Create Volatile Files and Directories.
[   19.259360] systemd-journald[78]: Received request to flush runtime journal f                                                                             rom PID 1
[  OK  ] Started Trigger Flushing of Journal to Persistent Storage.
         Starting Network Time Synchronization...
         Starting Update UTMP about System Boot/Shutdown...
[  OK  ] Found device /dev/ttyS0.
[   20.067656] usbcore: registered new interface driver uas
[   20.077709] random: nonblocking pool is initialized
[  OK  ] Started Update UTMP about System Boot/Shutdown.
[  OK  ] Started Network Time Synchronization.
[  OK  ] Reached target System Time Synchronized.
[  OK  ] Reached target System Initialization.
[  OK  ] Listening on D-Bus System Message Bus Socket.
[  OK  ] Reached target Sockets.
[  OK  ] Reached target Timers.
[  OK  ] Reached target Basic System.
         Starting Entropy Harvesting Daemon...
         Starting Login Service...
         Starting D-Bus System Message Bus...
[  OK  ] Started D-Bus System Message Bus.
         Starting Network Service...
         Starting Permit User Sessions...
[  OK  ] Started Entropy Harvesting Daemon.
[  OK  ] Started Permit User Sessions.
[  OK  ] Started Login Service.
[  OK  ] Started Network Service.
[  OK  ] Reached target Network.
         Starting OpenSSH Daemon...
[  OK  ] Started OpenSSH Daemon.
         Starting Network Name Resolution...
         Starting Getty on tty1...
[  OK  ] Started Getty on tty1.
         Starting Serial Getty on ttyS0...
[  OK  ] Started Serial Getty on ttyS0.
[  OK  ] Reached target Login Prompts.
[  OK  ] Started Network Name Resolution.
[  OK  ] Reached target Multi-User System.
[  OK  ] Reached target Graphical Interface.

Arch Linux 3.16.2-1-ARCH (ttyS0)

alarm login:

When I rebooted it got the same problem as before so I did the same input but added saveenv. It didn't help.
But at least Arch is booting :)

So I have three questions left.
1 How do I save this changes so the pogoplug automaticly reboots in arch?
2 How do I set the original pogo software when I am nut plugging in a usb device with the arch kernel?
3 My pogoplug gets a kernel crash when I insert my sagate hdd. I don't know if you can help me with that but I read somewhere I need to change UAS settings 
fw_setenv usb_custom_params usb-storage.quirks=0x0bc2:0x3321:u

Do you know where I need to put insert this line/how to get it working?



Edited 3 time(s). Last edit at 10/22/2014 09:33AM by devinger.
Reply Quote
bodhi
Re: PogoPlug V4 won't boot after failed env input
October 22, 2014 12:01PM
Cool!

Quote

1 How do I save this changes so the pogoplug automaticly reboots in arch?

Strange that your boot cmd was disabled. What you did originally could not have affect this boot cmd. I will have to look at your envs listing again closely.

Quote

3 My pogoplug gets a kernel crash when I insert my sagate hdd. I don't know if you can help me with that but I read somewhere I need to change UAS settings

At the serial prompt, add it to the end of bootargs 
setenv usb_custom_params 'usb-storage.quirks=0x0bc2:0x3321:u'
setenv set_bootargs_usb 'setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts $usb_custom_param'

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)



Edited 2 time(s). Last edit at 10/22/2014 04:28PM by bodhi.
Reply Quote
devinger
Re: PogoPlug V4 won't boot after failed env input
October 22, 2014 12:32PM
How and where do I enter it in bootargs? Directly in uboot or somewhere else because fw_setenv is not accepted as a command :)

The pogoplug now restarts correctly with boot and after waiting untill the countdown is finished. I didn't check it correctly

Thanks again for all the time and effort



Edited 1 time(s). Last edit at 10/22/2014 12:38PM by devinger.
Reply Quote
bodhi
Re: PogoPlug V4 won't boot after failed env input
October 22, 2014 04:30PM
I've edited the post above. Enter these the same way you did previouly.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Reply Quote
devinger
Re: PogoPlug V4 won't boot after failed env input
October 22, 2014 04:47PM
I allready tried that: 

U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45)
Pogoplug V4

SoC:   Kirkwood 88F6192_A1
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  128 MiB
MMC:   kwsdio: 0
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Hit any key to stop autoboot:  0
Pogov4> setenv usb_custom_params 'usb-storage.quirks=0x0bc2:0x3321:u'
Pogov4> setenv set_bootargs_usb 'setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts $usb_custom_param'
Pogov4> boot

After the boot I plug the device in and still get a kernel panic :( 

[  232.306382] WARNING: CPU: 0 PID: 43 at drivers/usb/storage/uas.c:157 uas_mark_cmd_dead+0x88/0xc8 [uas]()
[  232.315818] Modules linked in: uas mv_cesa ipv6
[  232.320370] CPU: 0 PID: 43 Comm: kworker/u2:2 Tainted: G      D W     3.16.2-1-ARCH #1
[  232.328273] Workqueue: scsi_tmf_2 scmd_eh_abort_handler
[  232.333508] [<c000f040>] (unwind_backtrace) from [<c000c588>] (show_stack+0x10/0x14)
[  232.341225] [<c000c588>] (show_stack) from [<c001b7bc>] (warn_slowpath_common+0x70/0x90)
[  232.349293] [<c001b7bc>] (warn_slowpath_common) from [<c001b878>] (warn_slowpath_null+0x1c/0x24)
[  232.358049] [<c001b878>] (warn_slowpath_null) from [<bf06b560>] (uas_mark_cmd_dead+0x88/0xc8 [uas])
[  232.367080] [<bf06b560>] (uas_mark_cmd_dead [uas]) from [<bf06cbb0>] (uas_eh_abort_handler+0x88/0x160 [uas])
[  232.376882] [<bf06cbb0>] (uas_eh_abort_handler [uas]) from [<c036a7d8>] (scmd_eh_abort_handler+0x7c/0x140)
[  232.386511] [<c036a7d8>] (scmd_eh_abort_handler) from [<c0033a1c>] (process_one_work+0x140/0x464)
[  232.395353] [<c0033a1c>] (process_one_work) from [<c00345c8>] (worker_thread+0x38/0x618)
[  232.403420] [<c00345c8>] (worker_thread) from [<c0039fd4>] (kthread+0xbc/0xd8)
[  232.410620] [<c0039fd4>] (kthread) from [<c0009590>] (ret_from_fork+0x14/0x24)
[  232.417807] ---[ end trace 45416352fa9dde13 ]---
[  232.437044] Unable to handle kernel NULL pointer dereference at virtual address 00000001
[  232.445113] pgd = c7164000
[  232.447811] [00000001] *pgd=00000000
[  232.451385] Internal error: Oops: 1 [#2] PREEMPT ARM
[  232.456331] Modules linked in: uas mv_cesa ipv6
[  232.460883] CPU: 0 PID: 77 Comm: systemd-journal Tainted: G      D W     3.16.2-1-ARCH #1
[  232.469025] task: c7118fc0 ti: c7134000 task.ti: c7134000
[  232.474411] PC is at dev_vprintk_emit+0x10c/0x154
[  232.479101] LR is at dev_printk_emit+0x20/0x30
[  232.483527] pc : [<c0344fe0>]    lr : [<c0345048>]    psr: 20000093
[  232.483527] sp : c7135d18  ip : c7135de4  fp : c781e068
[  232.494953] r10: c0673dc0  r9 : c7135de4  r8 : 00000006
[  232.500155] r7 : c71c4160  r6 : 20000093  r5 : c71c4290  r4 : c7135e00
[  232.506652] r3 : 00000001  r2 : c0673dc0  r1 : 00000000  r0 : 00000006
[  232.513150] Flags: nzCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment user
[  232.520338] Control: 0005397f  Table: 07164000  DAC: 00000015
[  232.526057] Process systemd-journal (pid: 77, stack limit = 0xc71341c0)
[  232.532641] Stack: (0xc7135d18 to 0xc7136000)
[  232.536982] 5d00:                                                       00001000 00000000
[  232.545124] 5d20: 00800001 00000000 000c0002 00000000 000c0002 00000000 00000271 00001000
[  232.553272] 5d40: c7135d68 c7b99800 00000040 c7134018 c7029d50 c00bd9dc c76757a8 00000000
[  232.561420] 5d60: 00000000 00800000 c7b99800 00000138 c074ae4c c01073d0 00000200 00000000
[  232.569567] 5d80: c76757a8 c0186864 00000000 c017d9d0 c7a8a528 c767586c c7fc1e20 c767586c
[  232.577715] 5da0: 60000013 00000001 0637110f c7135e00 bf06e4d0 20000093 c71c4160 00000000
[  232.585863] 5dc0: 00000001 c73b1350 c781e068 c0345048 c074d020 c7135de4 c0014610 c03450a0
[  232.594010] 5de0: c0673dc0 ea0003ff c71c42a0 c7135e00 c71c40e0 c0345114 00000002 c7135e14
[  232.602158] 5e00: bf06de50 c7135dfc c72f5800 bf06bcec bf06de50 00000000 00000000 c72f5800
[  232.610306] 5e20: c71c40e0 bf06c034 c72f5800 c71ac3f0 c781e068 c72f5800 c71ac3f0 20000093
[  232.618453] 5e40: c7b33600 c03e4ba4 c73b1320 c72f5800 c781e000 c040b2e8 c73b1300 c72ba124
[  232.626599] 5e60: c73b1300 c72ba134 c781e000 c040c29c 071c24d0 00000000 000000a9 c0532980
[  232.634746] 5e80: c717802d 00000001 00000002 07163001 c73b1340 00000001 00000800 00000000
[  232.642895] 5ea0: 00000000 00000000 071c24c0 c8906410 00000000 c72ba124 c71bfba0 c781e000
[  232.651042] 5ec0: c73b1300 00000000 c73b1300 c040e7f4 00000071 c7134030 00002000 0000000a
[  232.659190] 5ee0: c7178000 00000000 0000001a c7134010 c8906400 00000002 071c24c0 c7135fb0
[  232.667337] 5f00: 00000000 b6f86cf8 befd3e6c ffffff8d 00002000 c7b19600 c7b19600 00000009
[  232.675485] 5f20: c7135fb0 7b000000 00000000 00000000 c0792b64 c03e4138 c03e4114 c0059440
[  232.683632] 5f40: ffffffff 00000000 00000000 c075cf10 00001784 c075cf10 c7b19600 00000000
[  232.691781] 5f60: c7135fb0 7b000000 00000000 b6f86cf8 befd3c9c c00596a4 00022000 c075cf10
[  232.699928] 5f80: 00000009 c005bd18 c0771850 c0058d58 00000072 c0009db0 e89c3e34 b6f6b414
[  232.708075] 5fa0: 20000010 fed20200 00000000 c0531258 e89c3e34 0ca8ac9e 0000b55f 48ae0000
[  232.716222] 5fc0: 00006d00 00000000 00270000 00000000 7b000000 00000000 b6f86cf8 befd3c9c
[  232.724370] 5fe0: 4e1a9ffb befd39b8 b6f63e58 b6f6b414 20000010 ffffffff 00000000 00000000
[  232.732526] [<c0344fe0>] (dev_vprintk_emit) from [<c0345048>] (dev_printk_emit+0x20/0x30)
[  232.740676] [<c0345048>] (dev_printk_emit) from [<c03450a0>] (__dev_printk+0x48/0x90)
[  232.748476] [<c03450a0>] (__dev_printk) from [<c0345114>] (dev_printk+0x2c/0x3c)
[  232.755862] [<c0345114>] (dev_printk) from [<bf06bcec>] (uas_try_complete.isra.13+0xc4/0x12c [uas])
[  232.764889] [<bf06bcec>] (uas_try_complete.isra.13 [uas]) from [<bf06c034>] (uas_data_cmplt+0x54/0x1b4 [uas])
[  232.774783] [<bf06c034>] (uas_data_cmplt [uas]) from [<c03e4ba4>] (__usb_hcd_giveback_urb+0x60/0xd8)
[  232.783897] [<c03e4ba4>] (__usb_hcd_giveback_urb) from [<c040b2e8>] (xhci_giveback_urb_in_irq.isra.28+0xac/0xe0)
[  232.794041] [<c040b2e8>] (xhci_giveback_urb_in_irq.isra.28) from [<c040c29c>] (handle_cmd_completion+0x778/0xbf4)
[  232.804268] [<c040c29c>] (handle_cmd_completion) from [<c040e7f4>] (xhci_irq+0x418/0x152c)
[  232.812509] [<c040e7f4>] (xhci_irq) from [<c03e4138>] (usb_hcd_irq+0x24/0x38)
[  232.819632] [<c03e4138>] (usb_hcd_irq) from [<c0059440>] (handle_irq_event_percpu+0x34/0x248)
[  232.828133] [<c0059440>] (handle_irq_event_percpu) from [<c00596a4>] (handle_irq_event+0x50/0x84)
[  232.836978] [<c00596a4>] (handle_irq_event) from [<c005bd18>] (handle_level_irq+0x98/0x16c)
[  232.845298] [<c005bd18>] (handle_level_irq) from [<c0058d58>] (generic_handle_irq+0x20/0x34)
[  232.853706] [<c0058d58>] (generic_handle_irq) from [<c0009db0>] (handle_IRQ+0x44/0xb0)
[  232.861598] [<c0009db0>] (handle_IRQ) from [<c0531258>] (__irq_usr+0x38/0xa0)
[  232.868710] Code: eaffffe3 e5953040 e3530000 0a000009 (e5937000)
[  232.874781] ---[ end trace 45416352fa9dde14 ]---
[  232.879382] Kernel panic - not syncing: Fatal exception in interrupt
[  232.885710] ---[ end Kernel panic - not syncing: Fatal exception in interrupt
Reply Quote
devinger
Re: PogoPlug V4 won't boot after failed env input
October 22, 2014 07:42PM
@grayman


I tried to use input the parameters. I am sure I did some input wrong but I don't know what. 192.168.178.22 is my pc, 192.168.178.24 is the pogoplug This is what I used: 

arcNumber=3960
baudrate=115200
setenv bootcmd 'run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; reset'
setenv bootcmd_mmc 'run mmc_init; run set_bootargs_mmc; run mmc_boot'
setenv bootcmd_sata 'run sata_init; run set_bootargs_sata; run sata_boot;'
setenv bootcmd_usb 'run usb_init; run set_bootargs_usb; run usb_boot;'
bootdelay=10
console=ttyS0,115200
device=0:1
ethact=egiga0
ethaddr=00:25:31:04:ED:6A
setenv if_netconsole 'ping $serverip'
ipaddr=192.168.178.22
setenv led_error 'orange blinking'
setenv led_exit 'green off'
setenv led_init 'green blinking'
machid=F78
mainlineLinux=yes
setenv mmc_boot 'mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi'
setenv mmc_init 'mmc rescan'
setenv mmc_load_uimage 'ext2load mmc $device 0x800000 /boot/uImage'
setenv mmc_load_uinitrd 'ext2load mmc $device 0x1100000 /boot/uInitrd'
mmc_root=/dev/mmcblk0p1
mtddevname=uImage2
mtddevnum=2
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
ncip=192.168.178.24
partition=nand0,2
setenv preboot 'run if_netconsole start_netconsole'
setenv preboot_nc 'run if_netconsole start_netconsole'
rootdelay=10
rootfstype=ext2
setenv sata_boot 'mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi'
setenv sata_init 'ide reset'
setenv sata_load_uimage 'ext2load ide $device 0x800000 /boot/uImage'
setenv sata_load_uinitrd 'ext2load ide $device 0x1100000 /boot/uInitrd'
sata_root=/dev/sda1
serverip=192.168.178.22
setenv set_bootargs_mmc 'setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts'
setenv set_bootargs_sata 'setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts'
setenv set_bootargs_usb 'setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts'
setenv start_netconsole 'setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;'
stderr=nc
stdin=nc
stdout=nc
setenv usb_boot 'mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi'
setenv usb_init 'usb start'
setenv usb_load_uimage 'ext2load usb $device 0x800000 /boot/uImage'
setenv usb_load_uinitrd 'ext2load usb $device 0x1100000 /boot/uInitrd'
usb_root=/dev/sda1
usb_rootfstype=ext2

rebooted and got this: 
SoC:   Kirkwood 88F6192_A1
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  128 MiB
MMC:   kwsdio: 0
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Using egiga0 device
ping failed; host 192.168.0.220 is not alive
Hit any key to stop autoboot:  0
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
** Bad device usb 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
** Bad device mmc 0 **
** Bad device mmc 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!

Reset IDE: ide_preinit failed
** Bad device size - ide 0 **
** Bad device size - ide 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
resetting ...

I am sorry for not letting you know what happened earlier.
Reply Quote
bodhi
Re: PogoPlug V4 won't boot after failed env input
October 23, 2014 12:39AM
devinger,

> 'usb-storage.quirks=0x0bc2:0x3321:u'

Are you sure the quirk name is correct?

And to verify that the kernel took is as a parameter, look at the beginning of dmesg for kernel command line.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Reply Quote
devinger
Re: PogoPlug V4 won't boot after failed env input
October 23, 2014 07:05AM
You are right, it doesn't take it as a parameter: 

[    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext3 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)

I got the device id like this: 

[root@alarm ~]# lsusb
Bus 001 Device 002: ID 0781:5571 SanDisk Corp. Cruzer Fit
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 002: ID 0bc2:3321 Seagate RSS LLC
Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Reply Quote
bodhi
Re: PogoPlug V4 won't boot after failed env input
October 23, 2014 08:32PM
Instead of using $usb_customparams in set_bootargs_usb, put that quirk string in the env directly. See if it will take.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Reply Quote
devinger
Re: PogoPlug V4 won't boot after failed env input
October 24, 2014 07:17PM
Not sure if I did it right, I tried this: 

setenv set_bootargs_usb 'setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts $usb-storage.quirks=0x0bc2:0x3321:u'

and got a few seconds after loading the system and plugging in the hdd the usual kernel panic.

But, the dmesg changes! :) 
[    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext3 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) -storage.quirks=0x0bc2:0x3321:u

Almost certain I do something wrong with the input. I am very great full for the time you put in to me to help!



Edited 1 time(s). Last edit at 10/24/2014 07:31PM by devinger.
Reply Quote
bodhi
Re: PogoPlug V4 won't boot after failed env input
October 24, 2014 08:15PM
devinger,

Remove the $ 

> setenv set_bootargs_usb 'setenv bootargs
> console=$console root=$usb_root
> rootdelay=$rootdelay rootfstype=$rootfstype
> $mtdparts usb-storage.quirks=0x0bc2:0x3321:u'
>

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Reply Quote
devinger
Re: PogoPlug V4 won't boot after failed env input
October 25, 2014 01:40PM
Yeaaah I tought I tried it, but I made a typo so I did it again and.. I worked! 

setenv set_bootargs_usb 'setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts usb-storage.quirks=0x0bc2:0x3321:u'

Thank youu for all your patients and help! I can't say it enough!
Reply Quote
kanote
Re: PogoPlug V4 won't boot after failed env input
March 08, 2015 09:26AM
I have a similar problem :( 

U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45)
Pogoplug V4

SoC:   Kirkwood 88F6192_A1
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  128 MiB
MMC:   kwsdio: 0
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Warning: failed to set MAC address

Hit any key to stop autoboot:  0
Pogov4> setenv arcNumber 3960
Pogov4> setenv machid F78
Pogov4> setenv ethaddr 00:25:31:05:12:c6
Pogov4> boot
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
4054464 bytes read in 359 ms (10.8 MiB/s)
** File not found /boot/uInitrd **
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-3.19.0-1-ARCH
   Created:      2015-02-10   4:56:00 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4054400 Bytes = 3.9 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
Using machid 0xf78 from environment

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.19.0-1-ARCH (builduser@leming) (gcc version 4.9.2 20141224 (prerelease) (GCC) ) #1 PREEMPT Mon Feb 9 21:55:44 MST 2015
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: Pogoplug V4
[    0.000000] Memory policy: Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext3 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 120980K/131072K available (5722K kernel code, 354K rwdata, 1720K rodata, 268K init, 698K bss, 10092K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff000000   ( 872 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc074ccd4   (7444 kB)
[    0.000000]       .init : 0xc074d000 - 0xc0790000   ( 268 kB)
[    0.000000]       .data : 0xc0790000 - 0xc07e88bc   ( 355 kB)
[    0.000000]        .bss : 0xc07e88bc - 0xc08972b8   ( 699 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:114
[    0.000019] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 25769803770ns
[    5.207220] Console: colour dummy device 80x30
[    5.207260] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216)
[    5.297036] pid_max: default: 32768 minimum: 301
[    5.297181] Security Framework initialized
[    5.297295] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    5.297325] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    5.298374] Initializing cgroup subsys memory
[    5.298442] Initializing cgroup subsys devices
[    5.298479] Initializing cgroup subsys freezer
[    5.298512] Initializing cgroup subsys net_cls
[    5.298539] Initializing cgroup subsys blkio
[    5.298565] Initializing cgroup subsys bfqio
[    5.298592] Initializing cgroup subsys perf_event
[    5.298622] Initializing cgroup subsys net_prio
[    5.298756] CPU: Testing write buffer coherency: ok
[    5.299418] Setting up static identity map for 0x5741d0 - 0x574228
[    5.302283] devtmpfs: initialized
[    5.306491] pinctrl core: initialized pinctrl subsystem
[    5.307562] NET: Registered protocol family 16
[    5.308297] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    5.337071] cpuidle: using governor ladder
[    5.367070] cpuidle: using governor menu
[    5.367298] Kirkwood: MV88F6281-A1, TCLK=166666667.
[    5.367334] Feroceon L2: Enabling L2
[    5.367386] Feroceon L2: Cache support initialised.
[    5.370761] Kirkwood PCIe port 0: link up
[    5.370776] PCI: bus0 uses PCIe port 0
[    5.371122] PCI host bridge to bus 0000:00
[    5.371150] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[    5.371168] pci_bus 0000:00: root bus resource [io  0x1000-0xffff]
[    5.371183] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    5.372292] PCI: bus0: Fast back to back transfers disabled
[    5.372368] pci 0000:00:01.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff 64bit]
[    5.372401] pci 0000:00:01.0: BAR 2: assigned [mem 0xe0010000-0xe0010fff 64bit]
[    5.372431] pci 0000:00:01.0: BAR 4: assigned [mem 0xe0011000-0xe0011fff 64bit]
[    5.409454] vgaarb: loaded
[    5.409945] SCSI subsystem initialized
[    5.410677] usbcore: registered new interface driver usbfs
[    5.410789] usbcore: registered new interface driver hub
[    5.410877] usbcore: registered new device driver usb
[    5.411114] pps_core: LinuxPPS API ver. 1 registered
[    5.411127] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    5.411177] PTP clock support registered
[    5.412785] Switched to clocksource orion_clocksource
[    5.439570] FS-Cache: Loaded
[    5.458307] NET: Registered protocol family 2
[    5.459559] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    5.459597] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    5.459626] TCP: Hash tables configured (established 1024 bind 1024)
[    5.459725] TCP: reno registered
[    5.459744] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    5.459775] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    5.460046] NET: Registered protocol family 1
[    5.460164] pci 0000:00:01.0: enabling device (0140 -> 0142)
[    5.462710] futex hash table entries: 256 (order: -1, 3072 bytes)
[    5.481352] VFS: Disk quotas dquot_6.5.2
[    5.481750] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    5.484715] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    5.486289] fuse init (API version 7.23)
[    5.489644] aufs 3.x-rcN-20150126
[    5.492581] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[    5.492613] io scheduler noop registered
[    5.492632] io scheduler deadline registered
[    5.493100] io scheduler cfq registered
[    5.493774] io scheduler bfq registered (default)
[    5.493787] BFQ I/O-scheduler version: v7r7
[    5.494108] mv_xor mv_xor.0: Marvell shared XOR driver
[    5.532924] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[    5.572908] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[    5.573178] mv_xor mv_xor.1: Marvell shared XOR driver
[    5.612887] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[    5.652886] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[    5.660824] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    5.662397] console [ttyS0] disabled
[    5.682492] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 10416666) is a 16550A
[    6.250000] console [ttyS0] enabled
[    6.267365] brd: module loaded
[    6.277039] loop: module loaded
[    6.280697] sata_mv sata_mv.0: cannot get optional clkdev
[    6.286211] sata_mv sata_mv.0: slots 32 ports 1
[    6.293336] scsi host0: sata_mv
[    6.297027] ata1: SATA max UDMA/133 irq 21
[    6.302743] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[    6.309122] nand: Hynix H27U1G8F2BTR-BC
[    6.313001] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    6.320556] Scanning device for bad blocks
[    6.359223] Bad eraseblock 421 at 0x0000034a0000
[    6.413186] 4 cmdlinepart partitions found on MTD device orion_nand
[    6.419426] Creating 4 MTD partitions on "orion_nand":
[    6.424571] 0x000000000000-0x000000100000 : "u-boot"
[    6.430227] 0x000000100000-0x000000500000 : "uImage"
[    6.435868] 0x000000500000-0x000002500000 : "rootfs"
[    6.441504] 0x000002500000-0x000008000000 : "data"
[    6.456210] libphy: orion_mdio_bus: probed
[    6.460455] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    6.642855] ata1: SATA link down (SStatus 0 SControl F300)
[    7.547057] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:00:00:00:00:00
[    7.556118] xhci_hcd 0000:00:01.0: xHCI Host Controller
[    7.561358] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 1
[    7.571472] hub 1-0:1.0: USB hub found
[    7.575342] hub 1-0:1.0: 2 ports detected
[    7.580218] xhci_hcd 0000:00:01.0: xHCI Host Controller
[    7.585523] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 2
[    7.594287] hub 2-0:1.0: USB hub found
[    7.598070] hub 2-0:1.0: 2 ports detected
[    7.603135] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.609644] ehci-pci: EHCI PCI platform driver
[    7.614251] ehci-orion: EHCI orion driver
[    7.618353] orion-ehci orion-ehci.0: EHCI Host Controller
[    7.623824] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 3
[    7.631547] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[    7.652830] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[    7.660028] hub 3-0:1.0: USB hub found
[    7.663877] hub 3-0:1.0: 1 port detected
[    7.668715] usbcore: registered new interface driver uas
[    7.674519] usbcore: registered new interface driver usb-storage
[    7.680582] usbcore: registered new interface driver ums-alauda
[    7.686618] usbcore: registered new interface driver ums-cypress
[    7.692679] usbcore: registered new interface driver ums-datafab
[    7.699002] usbcore: registered new interface driver ums_eneub6250
[    7.705271] usbcore: registered new interface driver ums-freecom
[    7.711331] usbcore: registered new interface driver ums-isd200
[    7.717330] usbcore: registered new interface driver ums-jumpshot
[    7.723505] usbcore: registered new interface driver ums-karma
[    7.729389] usbcore: registered new interface driver ums-onetouch
[    7.735606] usbcore: registered new interface driver ums-realtek
[    7.741669] usbcore: registered new interface driver ums-sddr09
[    7.747674] usbcore: registered new interface driver ums-sddr55
[    7.753675] usbcore: registered new interface driver ums-usbat
[    7.760126] mousedev: PS/2 mouse device common for all mice
[    7.982861] usb 3-1: new high-speed USB device number 2 using orion-ehci
[    8.536709] usb-storage 3-1:1.0: USB Mass Storage device detected
[    8.543202] usb-storage 3-1:1.0: Quirks match for vid 13fe pid 3600: 4000
[    8.550122] scsi host1: usb-storage 3-1:1.0
[    8.772823] rtc-mv rtc-mv: internal RTC not ticking
[    8.777887] i2c /dev entries driver
[    8.782071] Driver 'mmcblk' needs updating - please use bus_type methods
[    8.788941] sdhci: Secure Digital Host Controller Interface driver
[    8.795120] sdhci: Copyright(c) Pierre Ossman
[    8.799561] mvsdio mvsdio: no pins associated
[    8.843100] sdhci-pltfm: SDHCI platform and OF driver helper
[    8.852600] ledtrig-cpu: registered to indicate activity on CPUs
[    8.858878] usbcore: registered new interface driver r8712u
[    8.864816] gre: GRE over IPv4 demultiplexor driver
[    8.869754] TCP: cubic registered
[    8.873152] NET: Registered protocol family 17
[    8.877800] Key type dns_resolver registered
[    8.884576] registered taskstats version 1
[    8.890591] console [netcon0] enabled
[    8.894342] netconsole: network logging started
[    8.899511] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[    8.906678] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    8.914617] Waiting 10 sec before mounting root device...
[    9.845963] scsi 1:0:0:0: Direct-Access              USB DISK 2.0     PMAP PQ: 0 ANSI: 0 CCS
[    9.856275] sd 1:0:0:0: Attached scsi generic sg0 type 0
[    9.861874] sd 1:0:0:0: [sda] 15646720 512-byte logical blocks: (8.01 GB/7.46 GiB)
[    9.872349] sd 1:0:0:0: [sda] Write Protect is off
[    9.879725] sd 1:0:0:0: [sda] No Caching mode page found
[    9.885082] sd 1:0:0:0: [sda] Assuming drive cache: write through
[    9.901086]  sda: sda1
[    9.910978] sd 1:0:0:0: [sda] Attached SCSI removable disk
[   18.924866] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[   19.723558] EXT4-fs (sda1): recovery complete
[   19.733988] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[   19.741700] VFS: Mounted root (ext3 filesystem) on device 8:1.
[   19.752969] devtmpfs: mounted
[   19.757265] Freeing unused kernel memory: 268K (c074d000 - c0790000)
[   20.204391] NET: Registered protocol family 10
[   20.210405] systemd[1]: Inserted module 'ipv6'
[   20.226636] random: systemd urandom read with 56 bits of entropy available
[   20.246230] systemd[1]: systemd 218 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID -ELFUTILS +KMOD +IDN)
[   20.264632] systemd[1]: Detected architecture 'arm'.

Welcome to Arch Linux ARM!

[   20.294463] systemd[1]: Set hostname to <alarm>.
[   21.038698] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
[   21.065008] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[   21.073764] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[   21.081953] systemd[1]: Starting Root Slice.
[  OK  ] Created slice Root Slice.
[   21.103043] systemd[1]: Created slice Root Slice.
[   21.107980] systemd[1]: Starting Journal Socket (/dev/log).
[  OK  ] Listening on Journal Socket (/dev/log).
[   21.133018] systemd[1]: Listening on Journal Socket (/dev/log).
[   21.139196] systemd[1]: Starting udev Kernel Socket.
[  OK  ] Listening on udev Kernel Socket.
[   21.163006] systemd[1]: Listening on udev Kernel Socket.
[   21.168522] systemd[1]: Starting LVM2 metadata daemon socket.
[  OK  ] Listening on LVM2 metadata daemon socket.
[   21.193001] systemd[1]: Listening on LVM2 metadata daemon socket.
[   21.199283] systemd[1]: Starting Delayed Shutdown Socket.
[  OK  ] Listening on Delayed Shutdown Socket.
[   21.222997] systemd[1]: Listening on Delayed Shutdown Socket.
[   21.228981] systemd[1]: Starting udev Control Socket.
[  OK  ] Listening on udev Control Socket.
[   21.253003] systemd[1]: Listening on udev Control Socket.
[   21.258607] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[   21.266741] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[   21.274676] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[  OK  ] Set up automount Arbitrary Executab...ats File System Automount Point.
[   21.303025] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[   21.312634] systemd[1]: Starting Device-mapper event daemon FIFOs.
[  OK  ] Listening on Device-mapper event daemon FIFOs.
[   21.342987] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[   21.349725] systemd[1]: Starting Remote File Systems.
[  OK  ] Reached target Remote File Systems.
[   21.372988] systemd[1]: Reached target Remote File Systems.
[   21.378751] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[  OK  ] Listening on /dev/initctl Compatibility Named Pipe.
[   21.403004] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[   21.410146] systemd[1]: Starting Paths.
[  OK  ] Reached target Paths.
[   21.432987] systemd[1]: Reached target Paths.
[   21.738743] systemd[1]: Listening on Journal Audit Socket.
[   21.744582] systemd[1]: Starting Encrypted Volumes.
[  OK  ] Reached target Encrypted Volumes.
[   21.773030] systemd[1]: Reached target Encrypted Volumes.
[   21.778718] systemd[1]: Starting System Slice.
[  OK  ] Created slice System Slice.
[   21.803025] systemd[1]: Created slice System Slice.
[   21.808216] systemd[1]: Starting system-serial\x2dgetty.slice.
[  OK  ] Created slice system-serial\x2dgetty.slice.
[   21.833025] systemd[1]: Created slice system-serial\x2dgetty.slice.
[   21.839619] systemd[1]: Starting Journal Socket.
[  OK  ] Listening on Journal Socket.
[   21.863015] systemd[1]: Listening on Journal Socket.
[   21.868318] systemd[1]: Starting udev Coldplug all Devices...
         Starting udev Coldplug all Devices...
[   21.898952] systemd[1]: Mounted Huge Pages File System.
[   21.910142] systemd[1]: Starting Remount Root and Kernel File Systems...
         Starting Remount Root and Kernel File Systems...
[   21.940256] systemd[1]: Mounting Debug File System...
         Mounting Debug File System...
[   22.020705] systemd[1]: Started Set Up Additional Binary Formats.
[   22.041138] systemd[1]: Started Load Kernel Modules.
[   22.047241] systemd[1]: Mounted Configuration File System.
[   22.053168] systemd[1]: Mounting Temporary Directory...
         Mounting Temporary Directory...
[   22.101623] systemd[1]: Starting Create list of required static device nodes for the current kernel...
         Starting Create list of required st... nodes for the current kernel...
[   22.148604] systemd[1]: Starting Journal Service...
         Starting Journal Service...
[   22.188838] systemd[1]: Mounting FUSE Control File System...
         Mounting FUSE Control File System...
[   22.228537] systemd[1]: Starting Setup Virtual Console...
         Starting Setup Virtual Console...
[   22.273512] systemd[1]: Starting Apply Kernel Variables...
         Starting Apply Kernel Variables...
[   22.328441] systemd[1]: Starting User and Session Slice.
[  OK  ] Created slice User and Session Slice.
[   22.373168] systemd[1]: Created slice User and Session Slice.
[   22.379689] systemd[1]: Starting Slices.
[  OK  ] Reached target Slices.
[   22.403135] systemd[1]: Reached target Slices.
[   22.409040] systemd[1]: Expecting device dev-ttyS0.device...
         Expecting device dev-ttyS0.device...
[   22.433195] systemd[1]: Starting system-getty.slice.
[  OK  ] Created slice system-getty.slice.
[   22.463136] systemd[1]: Created slice system-getty.slice.
[   22.468969] systemd[1]: Mounting POSIX Message Queue File System...
         Mounting POSIX Message Queue File System...
[   22.486484] systemd-journald[78]: File /var/log/journal/541b677484724c45b19ac52577fc2cc9/system.journal corrupted or uncleanly shut down, renaming and replacing.
[   22.506725] systemd[1]: Starting Swap.
[  OK  ] Reached target Swap.
[   22.523241] systemd[1]: Reached target Swap.
[  OK  ] Mounted FUSE Control File System.
[   22.553130] systemd[1]: Mounted FUSE Control File System.
[  OK  ] Mounted Debug File System.
[   22.583113] systemd[1]: Mounted Debug File System.
[  OK  ] Mounted Temporary Directory.
[   22.603077] systemd[1]: Mounted Temporary Directory.
[  OK  ] Mounted POSIX Message Queue File System.
[   22.633071] systemd[1]: Mounted POSIX Message Queue File System.
[  OK  ] Started Remount Root and Kernel File Systems.
[   22.673166] systemd[1]: Started Remount Root and Kernel File Systems.
[  OK  ] Started Create list of required sta...ce nodes for the current kernel.
[   22.723120] systemd[1]: Started Create list of required static device nodes for the current kernel.
[  OK  ] Started Setup Virtual Console.
[   22.763138] systemd[1]: Started Setup Virtual Console.
[  OK  ] Started Apply Kernel Variables.
[   22.783164] systemd[1]: Started Apply Kernel Variables.
[  OK  ] Started udev Coldplug all Devices.
[   22.943089] systemd[1]: Started udev Coldplug all Devices.
[  OK  ] Started Journal Service.
[   24.083152] systemd[1]: Started Journal Service.
         Starting Flush Journal to Persistent Storage...
         Starting Create Static Device Nodes in /dev...
         Starting Load/Save Random Seed...
[   24.785710] random: nonblocking pool is initialized
[  OK  ] Started Create Static Device Nodes in /dev.
[  OK  ] Started Load/Save Random Seed.
[   25.016758] systemd-journald[78]: Received request to flush runtime journal from PID 1
[  OK  ] Reached target Local File Systems (Pre).
[  OK  ] Reached target Local File Systems.
         Starting udev Kernel Device Manager...
[  OK  ] Started udev Kernel Device Manager.
[  OK  ] Started Flush Journal to Persistent Storage.
[  OK  ] Found device /dev/ttyS0.
[   28.319575] m25p80 spi0.0: m25p05-nonjedec (64 Kbytes)
         Starting Create Volatile Files and Directories...
[  OK  ] Started Create Volatile Files and Directories.
         Starting Network Time Synchronization...
         Starting Update UTMP about System Boot/Shutdown...
[  OK  ] Started Update UTMP about System Boot/Shutdown.
[  OK  ] Started Network Time Synchronization.
[  OK  ] Reached target System Time Synchronized.
[  OK  ] Reached target System Initialization.
[  OK  ] Listening on D-Bus System Message Bus Socket.
[  OK  ] Reached target Sockets.
[  OK  ] Reached target Basic System.
         Starting D-Bus System Message Bus...
[  OK  ] Started D-Bus System Message Bus.
         Starting Network Service...
         Starting Permit User Sessions...
         Starting Login Service...
         Starting Entropy Harvesting Daemon...
[  OK  ] Started Entropy Harvesting Daemon.
[  OK  ] Reached target Timers.
[  OK  ] Started Permit User Sessions.
[  OK  ] Started Network Service.
[  OK  ] Started Login Service.
[  OK  ] Reached target Network.
         Starting OpenSSH Daemon...
[  OK  ] Started OpenSSH Daemon.
         Starting Network Name Resolution...
         Starting Serial Getty on ttyS0...
[  OK  ] Started Serial Getty on ttyS0.
         Starting Getty on tty1...
[  OK  ] Started Getty on tty1.
[  OK  ] Reached target Login Prompts.
[  OK  ] Started Network Name Resolution.
[  OK  ] Reached target Multi-User System.
[  OK  ] Reached target Graphical Interface.

Arch Linux 3.19.0-1-ARCH (ttyS0)

alarm login: root
Password:
Last login: Wed Dec 10 22:17:03 on ttyS0
)"oot@alarm ~]# /tmp # /tmp/fw_setenv ethaddr "$(cat /sys/class/net/eth0/address
-bash: /tmp: Is a directory
[root@alarm ~]#

please help
Reply Quote
bodhi
Re: PogoPlug V4 won't boot after failed env input
March 08, 2015 04:00PM
kanote,

The problem: 

[    7.547057] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:00:00:00:00:00

Interrupt serial console and: 

setenv arcNumber 3960
setenv machid F78
setenv ethaddr 00:25:31:05:12:c6
saveenv
boot

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Reply Quote
Newer Topic Older Topic
Author:

Your Email:


Subject:
Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: