U-Boot VAMP 0.6 Pogoplug V4
Posted by rustyspoons
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 24, 2014 05:53AM |
Registered: 9 years ago Posts: 22 |
Hi Bodhi,
Dmesg output All seems to be working well, even picks up the SATA controller!
Cpuinfo
Led's None listed...
Finallly, check TOP, very little CPU/Mem usage, everyone said the V4 was no good for this, I think it's running just fine :)
Dmesg output All seems to be working well, even picks up the SATA controller!
[root@localhost ~]# dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.9.4-200.fc18.armv5tel.kirkwood (mockbuild@arm04-builder21.arm.fedoraproject.org) (gcc version 4.7.2 20121109 (Red Hat 4.7.2-8) (GCC) ) #1 Sun May 26 12:22:58 UTC 2013
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Marvell OpenRD Ultimate Board
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat c0718f54, node_mem_map c07ff000
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 rootfstype=ext3 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] allocated 262144 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 128MB = 128MB total
[ 0.000000] Memory: 106300k/106300k available, 24772k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xc8800000 - 0xff000000 ( 872 MB)
lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc066a014 (6537 kB)
.init : 0xc066b000 - 0xc06b6224 ( 301 kB)
.data : 0xc06b8000 - 0xc0724a00 ( 435 kB)
.bss : 0xc0724a00 - 0xc07feeec ( 874 kB)
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:114
[ 0.000000] sched_clock: 32 bits at 166MHz, resolution 5ns, wraps every 25769ms
[ 0.000000] Console: colour dummy device 80x30
[ 7.118806] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216)
[ 7.158597] pid_max: default: 32768 minimum: 301
[ 7.158849] Security Framework initialized
[ 7.158920] SELinux: Initializing.
[ 7.159034] SELinux: Starting in permissive mode
[ 7.159367] Mount-cache hash table entries: 512
[ 7.160358] Initializing cgroup subsys cpuacct
[ 7.160389] Initializing cgroup subsys memory
[ 7.160454] Initializing cgroup subsys devices
[ 7.160471] Initializing cgroup subsys freezer
[ 7.160486] Initializing cgroup subsys net_cls
[ 7.160498] Initializing cgroup subsys blkio
[ 7.160509] Initializing cgroup subsys perf_event
[ 7.160728] CPU: Testing write buffer coherency: ok
[ 7.160892] ftrace: allocating 19422 entries in 38 pages
[ 7.204861] Setting up static identity map for 0xc048adb0 - 0xc048adec
[ 7.222265] devtmpfs: initialized
[ 7.233291] atomic64 test passed
[ 7.233315] pinctrl core: initialized pinctrl subsystem
[ 7.233966] regulator-dummy: no parameters
[ 7.234543] NET: Registered protocol family 16
[ 7.236505] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[ 7.237686] Kirkwood: MV88F6281-A1, TCLK=166666667.
[ 7.237714] Feroceon L2: Enabling L2
[ 7.237762] Feroceon L2: Cache support initialised, in WT override mode.
[ 7.238457] initial MPP regs: 01111111 11113322 00551111 00100000 00000000 00000000 00000000
[ 7.238490] final MPP regs: 01111111 11113322 00551111 00000000 00000000 00000000 00000000
[ 7.240057] Kirkwood PCIe port 0: link up
[ 7.240071] PCI: bus0 uses PCIe port 0
[ 7.240290] PCI host bridge to bus 0000:00
[ 7.240318] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[ 7.240335] pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
[ 7.240350] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 7.240398] pci 0000:00:00.0: [11ab:6281] type 00 class 0x058000
[ 7.240433] pci 0000:00:00.0: reg 10: [mem 0xd0000000-0xd00fffff 64bit pref]
[ 7.240453] pci 0000:00:00.0: reg 18: [mem 0x00000000-0x07ffffff]
[ 7.240511] pci 0000:00:00.0: supports D1 D2
[ 7.240717] pci 0000:00:01.0: [1b73:1009] type 00 class 0x0c0330
[ 7.240755] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x0000ffff 64bit]
[ 7.240785] pci 0000:00:01.0: reg 18: [mem 0x00000000-0x00000fff 64bit]
[ 7.240815] pci 0000:00:01.0: reg 20: [mem 0x00000000-0x00000fff 64bit]
[ 7.240878] pci 0000:00:01.0: supports D1
[ 7.240894] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 7.241116] PCI: bus0: Fast back to back transfers disabled
[ 7.241138] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 7.241189] pci 0000:00:01.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff 64bit]
[ 7.241220] pci 0000:00:01.0: BAR 2: assigned [mem 0xe0010000-0xe0010fff 64bit]
[ 7.241249] pci 0000:00:01.0: BAR 4: assigned [mem 0xe0011000-0xe0011fff 64bit]
[ 7.247756] bio: create slab <bio-0> at 0
[ 7.248525] vgaarb: loaded
[ 7.249085] SCSI subsystem initialized
[ 7.249327] libata version 3.00 loaded.
[ 7.249678] usbcore: registered new interface driver usbfs
[ 7.249758] usbcore: registered new interface driver hub
[ 7.249921] usbcore: registered new device driver usb
[ 7.250946] NetLabel: Initializing
[ 7.250961] NetLabel: domain hash size = 128
[ 7.250969] NetLabel: protocols = UNLABELED CIPSOv4
[ 7.251039] NetLabel: unlabeled traffic allowed by default
[ 7.251246] Switching to clocksource orion_clocksource
[ 7.316495] NET: Registered protocol family 2
[ 7.317483] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 7.317534] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 7.317563] TCP: Hash tables configured (established 1024 bind 1024)
[ 7.317650] TCP: reno registered
[ 7.317668] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 7.317699] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 7.318047] NET: Registered protocol family 1
[ 7.318123] PCI: enabling device 0000:00:01.0 (0140 -> 0142)
[ 7.318220] PCI: CLS 32 bytes, default 32
[ 7.318533] Unpacking initramfs...
[ 9.374063] Freeing initrd memory: 15156K
[ 9.375214] audit: initializing netlink socket (disabled)
[ 9.375276] type=2000 audit(2.250:1): initialized
[ 9.562477] VFS: Disk quotas dquot_6.5.2
[ 9.562751] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 9.565659] msgmni has been set to 237
[ 9.566061] SELinux: Registering netfilter hooks
[ 9.568920] alg: No test for stdrng (krng)
[ 9.568954] NET: Registered protocol family 38
[ 9.569101] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 9.569304] io scheduler noop registered
[ 9.569317] io scheduler deadline registered
[ 9.569603] io scheduler cfq registered (default)
[ 9.570421] mv_xor mv_xor.0: Marvell shared XOR driver
[ 9.601447] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 9.641439] mv_xor mv_xor.0: Marvell XOR: ( xor fill cpy )
[ 9.641642] mv_xor mv_xor.1: Marvell shared XOR driver
[ 9.681436] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[ 9.721436] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
[ 9.722018] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 9.743554] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 10.326663] console [ttyS0] enabled
[ 10.336511] loop: module loaded
[ 10.340443] libphy: Fixed MDIO Bus: probed
[ 10.344889] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 10.351518] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 10.357039] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 10.364787] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 10.381320] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 10.387337] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 10.394121] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 10.401334] usb usb1: Product: Marvell Orion EHCI
[ 10.406018] usb usb1: Manufacturer: Linux 3.9.4-200.fc18.armv5tel.kirkwood ehci_hcd
[ 10.413652] usb usb1: SerialNumber: orion-ehci.0
[ 10.418996] hub 1-0:1.0: USB hub found
[ 10.422782] hub 1-0:1.0: 1 port detected
[ 10.427143] ehci-pci: EHCI PCI platform driver
[ 10.431689] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 10.437905] uhci_hcd: USB Universal Host Controller Interface driver
[ 10.444510] xhci_hcd 0000:00:01.0: xHCI Host Controller
[ 10.450030] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 2
[ 10.459104] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 10.465898] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 10.473107] usb usb2: Product: xHCI Host Controller
[ 10.477964] usb usb2: Manufacturer: Linux 3.9.4-200.fc18.armv5tel.kirkwood xhci_hcd
[ 10.485608] usb usb2: SerialNumber: 0000:00:01.0
[ 10.490739] xHCI xhci_add_endpoint called for root hub
[ 10.490752] xHCI xhci_check_bandwidth called for root hub
[ 10.490966] hub 2-0:1.0: USB hub found
[ 10.494753] hub 2-0:1.0: 2 ports detected
[ 10.499285] xhci_hcd 0000:00:01.0: xHCI Host Controller
[ 10.504784] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 3
[ 10.512276] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003
[ 10.519039] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 10.526268] usb usb3: Product: xHCI Host Controller
[ 10.531126] usb usb3: Manufacturer: Linux 3.9.4-200.fc18.armv5tel.kirkwood xhci_hcd
[ 10.538773] usb usb3: SerialNumber: 0000:00:01.0
[ 10.543980] xHCI xhci_add_endpoint called for root hub
[ 10.543993] xHCI xhci_check_bandwidth called for root hub
[ 10.544209] hub 3-0:1.0: USB hub found
[ 10.547962] hub 3-0:1.0: 2 ports detected
[ 10.552714] usbcore: registered new interface driver usbserial
[ 10.558591] usbcore: registered new interface driver usbserial_generic
[ 10.565163] usbserial: USB Serial support registered for generic
[ 10.571463] mousedev: PS/2 mouse device common for all mice
[ 10.761317] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 10.912305] usb 1-1: New USB device found, idVendor=18a5, idProduct=0302
[ 10.918997] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 10.926133] usb 1-1: Product: STORE N GO
[ 10.931791] usb 1-1: Manufacturer: Verbatim
[ 10.937870] usb 1-1: SerialNumber: 10V2600000002448
[ 11.581312] rtc-mv rtc-mv: internal RTC not ticking
[ 11.586931] device-mapper: uevent: version 1.0.3
[ 11.592098] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[ 11.600600] cpuidle: using governor ladder
[ 11.604704] cpuidle: using governor menu
[ 11.608726] hidraw: raw HID events driver (C) Jiri Kosina
[ 11.614935] usbcore: registered new interface driver usbhid
[ 11.620485] usbhid: USB HID core driver
[ 11.624460] drop_monitor: Initializing network drop monitor service
[ 11.631167] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.636550] TCP: cubic registered
[ 11.639851] Initializing XFRM netlink socket
[ 11.645276] NET: Registered protocol family 10
[ 11.650705] mip6: Mobile IPv6
[ 11.653707] NET: Registered protocol family 17
[ 11.659059] registered taskstats version 1
[ 11.663740] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 11.671978] Freeing init memory: 300K
[ 11.710407] systemd[1]: systemd 201 running in system mode. (+PAM +LIBWRAP +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ)
[ 11.723371] systemd[1]: Running in initial RAM disk.
[ 11.751786] systemd[1]: No hostname configured.
[ 11.756331] systemd[1]: Set hostname to <localhost>.
[ 11.761834] systemd[1]: Initializing machine ID from random generator.
[ 11.839445] systemd[1]: Cannot add dependency job for unit timers.target, ignoring: Unit timers.target failed to load: No such file or directory. See system logs and 'systemctl status timers.target' for details.
[ 11.858276] systemd[1]: Cannot add dependency job for unit paths.target, ignoring: Unit paths.target failed to load: No such file or directory. See system logs and 'systemctl status paths.target' for details.
[ 11.877350] systemd[1]: Starting Encrypted Volumes.
[ 11.901490] systemd[1]: Reached target Encrypted Volumes.
[ 11.907538] systemd[1]: Starting udev Kernel Socket.
[ 11.931475] systemd[1]: Listening on udev Kernel Socket.
[ 11.937361] systemd[1]: Starting udev Control Socket.
[ 11.961471] systemd[1]: Listening on udev Control Socket.
[ 11.966973] systemd[1]: Starting Journal Socket.
[ 11.991468] systemd[1]: Listening on Journal Socket.
[ 11.998035] systemd[1]: Started Load Kernel Modules.
[ 12.003136] systemd[1]: Starting Journal Service...
[ 12.047018] systemd-journald[39]: Failed to resolve 'systemd-journal' group: No such process
[ 12.055745] systemd[1]: Started Journal Service.
[ 12.071787] systemd[1]: Starting Sockets.
[ 12.091503] systemd[1]: Reached target Sockets.
[ 12.096202] systemd[1]: Starting dracut cmdline hook...
[ 12.135102] systemd[1]: Starting Swap.
[ 12.151664] systemd[1]: Reached target Swap.
[ 12.156088] systemd[1]: Starting Local File Systems.
[ 12.191576] systemd[1]: Reached target Local File Systems.
[ 13.346071] systemd-udevd[99]: starting version 201
[ 14.633558] mvsdio mvsdio: no pins associated
[ 14.669433] Initializing USB Mass Storage driver...
[ 14.681360] mmc0: mvsdio driver initialized, using GPIO 29 for card detection
[ 14.709139] sata_mv sata_mv.0: version 1.28
[ 14.709258] sata_mv sata_mv.0: cannot get optional clkdev
[ 14.734791] scsi0 : usb-storage 1-1:1.0
[ 14.739321] usbcore: registered new interface driver usb-storage
[ 14.745368] USB Mass Storage support registered.
[ 14.754425] sata_mv sata_mv.0: slots 32 ports 2
[ 14.801057] scsi1 : sata_mv
[ 14.808776] scsi2 : sata_mv
[ 14.812439] ata1: SATA max UDMA/133 irq 21
[ 14.816521] ata2: SATA max UDMA/133 irq 21
[ 15.161325] ata1: SATA link down (SStatus 0 SControl F300)
[ 15.511321] ata2: SATA link down (SStatus 0 SControl F300)
[ 15.732324] scsi 0:0:0:0: Direct-Access Verbatim STORE N GO 1.00 PQ: 0 ANSI: 2
[ 15.745131] sd 0:0:0:0: [sda] 7831552 512-byte logical blocks: (4.00 GB/3.73 GiB)
[ 15.755040] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 15.765880] sd 0:0:0:0: [sda] Write Protect is off
[ 15.770691] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
[ 15.778284] sd 0:0:0:0: [sda] No Caching mode page present
[ 15.783839] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 15.795360] sd 0:0:0:0: [sda] No Caching mode page present
[ 15.800859] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 15.816334] sda: sda1 sda2 sda3
[ 15.830744] sd 0:0:0:0: [sda] No Caching mode page present
[ 15.836287] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 15.842400] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 16.757969] EXT4-fs (sda3): INFO: recovery required on readonly filesystem
[ 16.764899] EXT4-fs (sda3): write access will be enabled during recovery
[ 16.961324] usb 1-1: reset high-speed USB device number 2 using orion-ehci
[ 47.321327] usb 1-1: reset high-speed USB device number 2 using orion-ehci
[ 56.051673] EXT4-fs (sda3): orphan cleanup on readonly fs
[ 56.057104] EXT4-fs (sda3): ext4_orphan_cleanup: deleting unreferenced inode 128015
[ 56.057482] EXT4-fs (sda3): ext4_orphan_cleanup: deleting unreferenced inode 128016
[ 56.057596] EXT4-fs (sda3): 2 orphan inodes deleted
[ 56.062524] EXT4-fs (sda3): recovery complete
[ 56.733343] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[ 57.142773] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[ 57.849000] systemd-journald[39]: Received SIGTERM
[ 58.464978] SELinux: Disabled at runtime.
[ 58.469129] SELinux: Unregistering netfilter hooks
[ 58.469201] type=1404 audit(51.340:2): selinux=0 auid=4294967295 ses=4294967295
[ 59.135918] systemd-readahead[245]: Disabling readahead replay due to low memory.
[ 59.160446] systemd-readahead[246]: Disabling readahead collector due to low memory.
[ 59.989817] systemd-udevd[250]: starting version 201
[ 61.362552] EXT4-fs (sda3): re-mounted. Opts: (null)
[ 62.243496] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 62.250463] libphy: mv643xx_eth smi: probed
[ 62.511360] usb 1-1: reset high-speed USB device number 2 using orion-ehci
[ 62.722613] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:05:2a:77
[ 62.786942] orion_wdt: Initial timeout 25 sec
[ 62.806389] ONFI param page 0 valid
[ 62.809872] ONFI flash detected
[ 62.813091] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix H27U1G8F2BTR-BC), 128MiB, page size: 2048, OOB size: 64
[ 62.876533] Scanning device for bad blocks
[ 63.023961] Creating 3 MTD partitions on "orion_nand":
[ 63.029095] 0x000000000000-0x000000100000 : "u-boot"
[ 63.070956] 0x000000100000-0x000000500000 : "uImage"
[ 63.088536] 0x000000500000-0x000008000000 : "root"
[ 63.106047] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:00:00:00:00:00
[ 63.352016] Adding 511996k swap on /dev/sda2. Priority:-1 extents:1 across:511996k
[ 63.585538] openrd-client-audio openrd-client-audio: ASoC: CODEC cs42l51-codec.0-004a not registered
[ 63.639930] openrd-client-audio openrd-client-audio: snd_soc_register_card() failed: -517
[ 63.651446] platform openrd-client-audio: Driver openrd-client-audio requests probe deferral
[ 66.853755] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem
[ 67.419020] EXT4-fs (sda1): mounted filesystem without journal. Opts: (null)
[ 68.127942] systemd[1]: Unit rngd.service entered failed state.
[ 72.342693] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 174.858681] usb 2-1: new full-speed USB device number 2 using xhci_hcd
[ 174.880098] usb 2-1: New USB device found, idVendor=08bb, idProduct=2704
[ 174.886784] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 174.893933] usb 2-1: Product: USB Audio DAC
[ 174.898359] usb 2-1: Manufacturer: Burr-Brown from TI
[ 174.905311] usb 2-1: ep 0x85 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 174.920963] input: Burr-Brown from TI USB Audio DAC as /devices/pci0000:00/0000:00:01.0/usb2/2-1/2-1:1.2/input/input0
[ 174.942809] hid-generic 0003:08BB:2704.0001: input,hidraw0: USB HID v1.00 Device [Burr-Brown from TI USB Audio DAC ] on usb-0000:00:01.0-1/input2
[ 174.959218] openrd-client-audio openrd-client-audio: ASoC: CODEC cs42l51-codec.0-004a not registered
[ 174.968343] openrd-client-audio openrd-client-audio: snd_soc_register_card() failed: -517
[ 174.983685] platform openrd-client-audio: Driver openrd-client-audio requests probe deferral
[ 175.113079] openrd-client-audio openrd-client-audio: ASoC: CODEC cs42l51-codec.0-004a not registered
[ 175.124600] openrd-client-audio openrd-client-audio: snd_soc_register_card() failed: -517
[ 175.134566] platform openrd-client-audio: Driver openrd-client-audio requests probe deferral
[ 175.147866] openrd-client-audio openrd-client-audio: ASoC: CODEC cs42l51-codec.0-004a not registered
[ 175.160682] usbcore: registered new interface driver snd-usb-audio
[ 175.167306] openrd-client-audio openrd-client-audio: snd_soc_register_card() failed: -517
[ 175.184507] platform openrd-client-audio: Driver openrd-client-audio requests probe deferral
[ 190.114916] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 190.124804] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 2780.393800] usb 1-1: reset high-speed USB device number 2 using orion-ehci
[ 2811.506515] usb 1-1: reset high-speed USB device number 2 using orion-ehci
[ 2811.513406] ALSA sound/usb/pcm.c:1350 delay: estimated 0, actual 220
[ 2811.516129] ALSA sound/usb/pcm.c:1350 delay: estimated 441, actual 220
[root@localhost ~]#
Cpuinfo
[root@localhost ~]# cat /proc/cpuinfo processor : 0 model name : Feroceon 88FR131 rev 1 (v5l) BogoMIPS : 795.44 Features : swp half thumb fastmult edsp CPU implementer : 0x56 CPU architecture: 5TE CPU variant : 0x2 CPU part : 0x131 CPU revision : 1 Hardware : Marvell OpenRD Ultimate Board Revision : 0000 Serial : 0000000000000000 [root@localhost ~]#
Led's None listed...
[root@localhost ~]# ls /sys/class/leds/ -l total 0
Finallly, check TOP, very little CPU/Mem usage, everyone said the V4 was no good for this, I think it's running just fine :)
Tasks: 64 total, 1 running, 63 sleeping, 0 stopped, 0 zombie
%Cpu(s): 2.4 us, 0.0 sy, 0.0 ni, 97.3 id, 0.0 wa, 0.0 hi, 0.3 si, 0.0 st
KiB Mem: 121756 total, 119448 used, 2308 free, 16208 buffers
KiB Swap: 511996 total, 220 used, 511776 free, 43792 cached
PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
627 squeezel 10 -10 12572 9m 3960 S 2.3 8.4 6:08.04 squeezelite
25929 root 20 0 5032 1276 1016 R 0.7 1.0 0:00.06 top
25895 root 20 0 13824 4224 3376 S 0.3 3.5 0:00.50 sshd
1 root 20 0 6160 3016 1792 S 0.0 2.5 0:06.21 systemd
2 root 20 0 0 0 0 S 0.0 0.0 0:00.05 kthreadd
3 root 20 0 0 0 0 S 0.0 0.0 0:04.90 ksoftirqd/0
5 root 0 -20 0 0 0 S 0.0 0.0 0:00.00 kworker/0:0H
6 root 20 0 0 0 0 S 0.0 0.0 0:00.01 kworker/u:0
7 root 0 -20 0 0 0 S 0.0 0.0 0:00.00 kworker/u:0H
8 root rt 0 0 0 0 S 0.0 0.0 0:00.26 watchdog/0
9 root 0 -20 0 0 0 S 0.0 0.0 0:00.00 khelper
10 root 20 0 0 0 0 S 0.0 0.0 0:00.00 kdevtmpfs
11 root 0 -20 0 0 0 S 0.0 0.0 0:00.00 netns
12 root 20 0 0 0 0 S 0.0 0.0 0:00.00 bdi-default
13 root 0 -20 0 0 0 S 0.0 0.0 0:00.00 kintegrityd
14 root 0 -20 0 0 0 S 0.0 0.0 0:00.00 kblockd
15 root 0 -20 0 0 0 S 0.0 0.0 0:00.00 ata_sff
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 24, 2014 06:05AM |
Admin Registered: 13 years ago Posts: 18,585 |
Dale,
> Finallly, check TOP, very little CPU/Mem
> usage, everyone said the V4 was no good for this,
> I think it's running just fine :)
Very nice :)
> [ 0.000000] Machine: Marvell OpenRD Ultimate
> Board
This is the reason. It was not identified as Pogo V4. The kernel is running it as OpenRD plug. My u-boot build has a wrong machid inside the code, but because setting it explicitly in u-boot env is enough to correct that, I did not bother fixing.
First, make sure your archNumber and machid are correct and in sync. See if you can boot the kernel at all, and what error it would spit out. And we go from there.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> Finallly, check TOP, very little CPU/Mem
> usage, everyone said the V4 was no good for this,
> I think it's running just fine :)
Very nice :)
> [ 0.000000] Machine: Marvell OpenRD Ultimate
> Board
This is the reason. It was not identified as Pogo V4. The kernel is running it as OpenRD plug. My u-boot build has a wrong machid inside the code, but because setting it explicitly in u-boot env is enough to correct that, I did not bother fixing.
First, make sure your archNumber and machid are correct and in sync. See if you can boot the kernel at all, and what error it would spit out. And we go from there.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 24, 2014 06:11AM |
Registered: 9 years ago Posts: 22 |
bodhi Wrote:
-------------------------------------------------------
> Dale,
>
> > Finallly, check TOP, very little CPU/Mem
> > usage, everyone said the V4 was no good for
> this,
> > I think it's running just fine :)
>
> Very nice :)
>
> > [ 0.000000] Machine: Marvell OpenRD Ultimate
> > Board
>
> This is the reason. It was not identified as Pogo
> V4. The kernel is running it as OpenRD plug. My
> u-boot build has a wrong machid inside the code,
> but because setting it explicitly in u-boot env is
> enough to correct that, I did not bother fixing.
>
> First, make sure your archNumber and machid are
> correct and in sync. See if you can boot the
> kernel at all, and what error it would spit out.
> And we go from there.
Bodhi, I have to clear the machid to get it to boot, I did notice looking at logs the E02 with VAMP has no machid.
If I set any machid regardless of arcNumber it will hang at uncompressing Kernel, I will see if any machid's work, maybe this kernel doesn't support or is not compiled to anything other than OpenRD?
Edited 2 time(s). Last edit at 10/24/2014 06:27AM by rustyspoons.
-------------------------------------------------------
> Dale,
>
> > Finallly, check TOP, very little CPU/Mem
> > usage, everyone said the V4 was no good for
> this,
> > I think it's running just fine :)
>
> Very nice :)
>
> > [ 0.000000] Machine: Marvell OpenRD Ultimate
> > Board
>
> This is the reason. It was not identified as Pogo
> V4. The kernel is running it as OpenRD plug. My
> u-boot build has a wrong machid inside the code,
> but because setting it explicitly in u-boot env is
> enough to correct that, I did not bother fixing.
>
> First, make sure your archNumber and machid are
> correct and in sync. See if you can boot the
> kernel at all, and what error it would spit out.
> And we go from there.
Bodhi, I have to clear the machid to get it to boot, I did notice looking at logs the E02 with VAMP has no machid.
If I set any machid regardless of arcNumber it will hang at uncompressing Kernel, I will see if any machid's work, maybe this kernel doesn't support or is not compiled to anything other than OpenRD?
Edited 2 time(s). Last edit at 10/24/2014 06:27AM by rustyspoons.
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 24, 2014 02:50PM |
Admin Registered: 13 years ago Posts: 18,585 |
@Dale,
> If I set any machid regardless of arcNumber it
> will hang at uncompressing Kernel, I will see if
> any machid's work, maybe this kernel doesn't
> support or is not compiled to anything other than
> OpenRD?
Probably. If you can find the link to the source code to build VAMP, post here and I'll take a look. As right now, it is running fine, so there is no need to be concerned. However, you should check the available memory to see if it is correct, because the OpenRD has 512M RAM.
Also, pls post the dmesg for the Pogo E02 running VAMP. Do you see it was identifed as a reference board, but not as Pogo E02?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> If I set any machid regardless of arcNumber it
> will hang at uncompressing Kernel, I will see if
> any machid's work, maybe this kernel doesn't
> support or is not compiled to anything other than
> OpenRD?
Probably. If you can find the link to the source code to build VAMP, post here and I'll take a look. As right now, it is running fine, so there is no need to be concerned. However, you should check the available memory to see if it is correct, because the OpenRD has 512M RAM.
Also, pls post the dmesg for the Pogo E02 running VAMP. Do you see it was identifed as a reference board, but not as Pogo E02?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 24, 2014 03:54PM |
Admin Registered: 13 years ago Posts: 18,585 |
According to the above, you are running with 128M RAM, so it does look OK:
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
KiB Mem: 121756 total, 119448 used, 2308 free, 16208 buffers
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: U-Boot VAMP 0.6 Pogoplug V4 January 12, 2015 03:13PM |
Registered: 9 years ago Posts: 24 |
Hi Bodhi and Dale-
I am trying to get VAMP working on my pogoplug V4.
I started today with a working Debian, which I achieved by following Quis blog.
I then updated U-Boot according to the 2014.07 U-Boot instructions (thanks Bodhi).
I then updated the pre-made environment according section B of that tutorial.
I then tried to cross reference that tutorial with this page to figure out how to get VAMP to work.
I have the VAMP 0.6 image on a USB drive. I made this by using dd on a linux computer.
I also have netconsole enabled.
I am still able to boot into Debian but I am not able to boot into VAMP.
Please note- I followed the netconsole instructions and I am able to "halt" the boot process, but I don't get a command prompt to enter commands at that time.
Nothing is bricked, but I would really like to get VAMP working as I am trying to use Squeezelite and failing epically with Debian.
Thanks and much love,
Peter
HERE IS THE OUTPUT OF PRINTENV
HERE IS THE OUTPUT THAT I GET IN NETCONSOLE WHEN I TRY TO BOOT WITH JUST THE USB VAMP
Edited 2 time(s). Last edit at 01/12/2015 03:38PM by monkmandolins.
I am trying to get VAMP working on my pogoplug V4.
I started today with a working Debian, which I achieved by following Quis blog.
I then updated U-Boot according to the 2014.07 U-Boot instructions (thanks Bodhi).
I then updated the pre-made environment according section B of that tutorial.
I then tried to cross reference that tutorial with this page to figure out how to get VAMP to work.
I have the VAMP 0.6 image on a USB drive. I made this by using dd on a linux computer.
I also have netconsole enabled.
I am still able to boot into Debian but I am not able to boot into VAMP.
Please note- I followed the netconsole instructions and I am able to "halt" the boot process, but I don't get a command prompt to enter commands at that time.
Nothing is bricked, but I would really like to get VAMP working as I am trying to use Squeezelite and failing epically with Debian.
Thanks and much love,
Peter
HERE IS THE OUTPUT OF PRINTENV
root@debian:~# fw_printenv ethaddr=b6:d0:5e:0f:a1:17 baudrate=115200 bootcmd=run bootcmd_uenv; run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; reset bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot; bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot; bootdelay=10 console=ttyS0,115200 device=0:1 ethact=egiga0 led_error=orange blinking led_exit=green off led_init=green blinking mainlineLinux=yes mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi mmc_init=mmc rescan mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd mmc_root=/dev/mmcblk0p1 mtdids=nand0=orion_nand partition=nand0,2 preboot_nc=run if_netconsole start_netconsole rootdelay=10 sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi sata_init=ide reset sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd sata_root=/dev/sda1 set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts stderr=serial stdin=serial stdout=serial usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_init=usb start bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi uenv_import=echo importing envs ...; env import -t 0x810000 uenv_load=usb start; mmc rescan; ide reset; setenv uenv_loaded 0; for devtype in usb mmc ide; do for disknum in 0; do run uenv_read_disk; done; done uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x810000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi arcNumber=3960 mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) rootfstype=ext3 serverip=10.42.0.1 ipaddr=10.42.0.96 if_netconsole=ping $serverip start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; preboot=run if_netconsole start_netconsole usb_load_uimage=ext2load usb 0x800000 /uImage usb_load_uinitrd=ext2load usb 0x1100000 /uInitrd usb_root=LABEL=rootfs
HERE IS THE OUTPUT THAT I GET IN NETCONSOLE WHEN I TRY TO BOOT WITH JUST THE USB VAMP
U-Boot 2014.07-tld-2 (Sep 19 2014 - 16:13:05)
Pogoplug V4
gcc (Debian 4.6.3-14) 4.6.3
GNU ld (GNU Binutils for Debian) 2.22
Hit any key to stop autoboot: 0
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Reset IDE: ide_preinit failed
Partition Map for USB device 0 -- Partition Type: DOS
Part Start Sector Num Sectors UUID Type
1 2048 409600 00081fe2-01 83
2 411648 1024000 00081fe2-02 82
3 1435648 6385664 00081fe2-03 83
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **
no IDE devices available
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
** Bad device usb 0x800000 **
** Bad device usb 0x1100000 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
** Bad device mmc 0 **
** Bad device mmc 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Reset IDE: ide_preinit failed
** Bad device size - ide 0 **
** Bad device size - ide 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
resetting ...
Edited 2 time(s). Last edit at 01/12/2015 03:38PM by monkmandolins.
|
Re: U-Boot VAMP 0.6 Pogoplug V4 January 12, 2015 11:09PM |
Admin Registered: 13 years ago Posts: 18,585 |
@monkmandolins,
If the above ddid not work, then make sure your rootfs (where /uImage and /uInitrd are) resides on partition 1.
See this post for explanation about booting process:
http://forum.doozan.com/read.php?3,19093
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
usb_load_uimage=ext2load usb 0x800000 /uImage usb_load_uinitrd=ext2load usb 0x1100000 /uInitrdshould be
usb_load_uimage=ext2load usb $device 0x800000 /uImage usb_load_uinitrd=ext2load usb $device 0x1100000 /uInitrd
If the above ddid not work, then make sure your rootfs (where /uImage and /uInitrd are) resides on partition 1.
See this post for explanation about booting process:
http://forum.doozan.com/read.php?3,19093
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: U-Boot VAMP 0.6 Pogoplug V4 January 14, 2015 09:53AM |
Registered: 9 years ago Posts: 24 |
Thanks Bodhi! This worked immediately!
The new login for VAMP 0.6, by the way, is user:root password:vamp
Do you have any idea how to get wifi working on this? The device is recognized, and here is the output of iwconfig:
And here is the output of ifconfig:
Thanks again for all of your help!
The new login for VAMP 0.6, by the way, is user:root password:vamp
Do you have any idea how to get wifi working on this? The device is recognized, and here is the output of iwconfig:
[root@localhost ~]# iwconfig
lo no wireless extensions.
eth1 no wireless extensions.
wlan0 IEEE 802.11bgn ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=27 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:on
eth0 no wireless extensions.
And here is the output of ifconfig:
[root@localhost ~]# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.42.0.36 netmask 255.255.255.0 broadcast 10.42.0.255
inet6 fe80::b4d0:5eff:fe0f:a117 prefixlen 64 scopeid 0x20<link>
ether b6:d0:5e:0f:a1:17 txqueuelen 1000 (Ethernet)
RX packets 1904 bytes 177846 (173.6 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 1172 bytes 690723 (674.5 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 11
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 0 (Local Loopback)
RX packets 8 bytes 892 (892.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 8 bytes 892 (892.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlan0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 00:0f:13:95:02:69 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
Thanks again for all of your help!
|
Re: U-Boot VAMP 0.6 Pogoplug V4 January 14, 2015 11:31AM |
Admin Registered: 13 years ago Posts: 18,585 |
monkmandolins,
I don't use VAMP so can't give you specific advice. Perhaps some VAMP-specific forums would have this info.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
I don't use VAMP so can't give you specific advice. Perhaps some VAMP-specific forums would have this info.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: U-Boot VAMP 0.6 Pogoplug V4 January 14, 2015 12:23PM |
Registered: 9 years ago Posts: 70 |
|
Re: U-Boot VAMP 0.6 Pogoplug V4 January 18, 2015 01:08PM |
Registered: 9 years ago Posts: 24 |
Hi
I got wireless working. The VAMP setup ended up being very choppy.
I will stop pestering about this, but I am really just wondering if there is a reliable and problem-free way to get squeezelite working on the Pogoplug.
When it plays (Arch) it works fantastic, but there have been enough issues that it required multiple reboots per day.
Any thoughts would be appreciated.
Peter
Edited 1 time(s). Last edit at 01/18/2015 01:58PM by monkmandolins.
I got wireless working. The VAMP setup ended up being very choppy.
I will stop pestering about this, but I am really just wondering if there is a reliable and problem-free way to get squeezelite working on the Pogoplug.
When it plays (Arch) it works fantastic, but there have been enough issues that it required multiple reboots per day.
Any thoughts would be appreciated.
Peter
Edited 1 time(s). Last edit at 01/18/2015 01:58PM by monkmandolins.
|
Re: U-Boot VAMP 0.6 Pogoplug V4 January 18, 2015 02:10PM |
Admin Registered: 13 years ago Posts: 18,585 |
monkmandolins,
You should not have to do more than just making sure your env config on VAMP is:
cat /etc/fw_env.config
(This was stated in the new u-boot instruction).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 01/18/2015 02:11PM by bodhi.
You should not have to do more than just making sure your env config on VAMP is:
cat /etc/fw_env.config
# MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd0 0xc0000 0x20000 0x20000
(This was stated in the new u-boot instruction).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 01/18/2015 02:11PM by bodhi.
