Goflex net bad blocks and no boot. October 24, 2014 03:36AM |
Registered: 9 years ago Posts: 64 |
U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:35:50) Seagate GoFlex Net SoC: Kirkwood 88F6281_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 88E1116 Initialized on egiga0 No link on egiga0 ping failed; host 192.168.178.26 is not alive Hit any key to stop autoboot: 0 (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found 2756040 bytes read in 477 ms (5.5 MiB/s) 6032465 bytes read in 592 ms (9.7 MiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.16.0-kirkwood-tld-2 Created: 2014-09-01 23:18:31 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2755976 Bytes = 2.6 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-3.16.0-kirkwood-tld-2 Created: 2014-09-01 23:18:48 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6032401 Bytes = 5.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.16.0-kirkwood-tld-2 (root@tldDebian) (gcc version 4.6.3 (Debian 4.6.3-14) ) #2 PREEMPT Sun Aug 31 18:56:01 PDT 2014 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: Seagate GoFlex Net [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext3 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 115744K/131072K available (5441K kernel code, 397K rwdata, 1840K rodata, 257K init, 299K bss, 15328K reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc07248b0 (7283 kB) [ 0.000000] .init : 0xc0725000 - 0xc0765444 ( 258 kB) [ 0.000000] .data : 0xc0766000 - 0xc07c975c ( 398 kB) [ 0.000000] .bss : 0xc07c975c - 0xc08144dc ( 300 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:114 [ 0.000011] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474836475ns [ 20.493464] Console: colour dummy device 80x30 [ 20.493492] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584) [ 20.583246] pid_max: default: 32768 minimum: 301 [ 20.583363] Security Framework initialized [ 20.583430] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 20.583449] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 20.584320] Initializing cgroup subsys devices [ 20.584383] Initializing cgroup subsys freezer [ 20.584412] Initializing cgroup subsys net_cls [ 20.584459] Initializing cgroup subsys blkio [ 20.584557] CPU: Testing write buffer coherency: ok [ 20.585027] Setting up static identity map for 0x5273f0 - 0x527448 [ 20.587399] devtmpfs: initialized [ 20.591378] prandom: seed boundary self test passed [ 20.595443] prandom: 100 self tests passed [ 20.595474] pinctrl core: initialized pinctrl subsystem [ 20.595987] regulator-dummy: no parameters [ 20.596461] NET: Registered protocol family 16 [ 20.596916] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 20.598166] cpuidle: using governor ladder [ 20.598194] cpuidle: using governor menu [ 20.598334] Kirkwood: MV88F6281-A1, TCLK=200000000. [ 20.598358] Feroceon L2: Enabling L2 [ 20.598397] Feroceon L2: Cache support initialised. [ 20.634770] vgaarb: loaded [ 20.635126] usbcore: registered new interface driver usbfs [ 20.635203] usbcore: registered new interface driver hub [ 20.635328] usbcore: registered new device driver usb [ 20.636324] Switched to clocksource orion_clocksource [ 20.675100] NET: Registered protocol family 2 [ 20.676090] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 20.676115] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 20.676135] TCP: Hash tables configured (established 1024 bind 1024) [ 20.676206] TCP: reno registered [ 20.676219] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 20.676241] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 20.676505] NET: Registered protocol family 1 [ 20.676843] RPC: Registered named UNIX socket transport module. [ 20.676855] RPC: Registered udp transport module. [ 20.676862] RPC: Registered tcp transport module. [ 20.676870] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 20.677181] Unpacking initramfs... [ 21.179454] Freeing initrd memory: 5884K (c1101000 - c16c0000) [ 21.179593] NetWinder Floating Point Emulator V0.97 (double precision) [ 21.180756] futex hash table entries: 256 (order: -1, 3072 bytes) [ 21.180825] audit: initializing netlink subsys (disabled) [ 21.180880] audit: type=2000 audit(0.680:1): initialized [ 21.181700] zbud: loaded [ 21.181972] VFS: Disk quotas dquot_6.5.2 [ 21.182023] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 21.182586] NFS: Registering the id_resolver key type [ 21.182645] Key type id_resolver registered [ 21.182655] Key type id_legacy registered [ 21.182681] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 21.182696] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 21.182867] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 21.183178] msgmni has been set to 237 [ 21.183331] Key type big_key registered [ 21.185686] alg: No test for stdrng (krng) [ 21.185805] bounce: pool size: 64 pages [ 21.185872] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 21.185891] io scheduler noop registered [ 21.185906] io scheduler deadline registered [ 21.186076] io scheduler cfq registered (default) [ 21.186592] mv_xor mv_xor.0: Marvell shared XOR driver [ 21.226404] mv_xor mv_xor.0: Marvell XOR: ( xor cpy ) [ 21.266391] mv_xor mv_xor.0: Marvell XOR: ( xor cpy ) [ 21.266567] mv_xor mv_xor.1: Marvell shared XOR driver [ 21.306390] mv_xor mv_xor.1: Marvell XOR: ( xor cpy ) [ 21.346388] mv_xor mv_xor.1: Marvell XOR: ( xor cpy ) [ 21.346820] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 21.347824] console [ttyS0] disabled [ 21.367924] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 12500000) is a 16550A [ 21.915194] console [ttyS0] enabled [ 21.920126] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda [ 21.926537] nand: Micron MT29F2G08AAD [ 21.930215] nand: 256MiB, SLC, page size: 2048, OOB size: 64 [ 21.935908] Scanning device for bad blocks [ 22.103884] Bad eraseblock 1534 at 0x00000bfc0000 [ 22.163412] 4 cmdlinepart partitions found on MTD device orion_nand [ 22.169726] Creating 4 MTD partitions on "orion_nand": [ 22.174894] 0x000000000000-0x000000100000 : "u-boot" [ 22.180291] 0x000000100000-0x000000500000 : "uImage" [ 22.185644] 0x000000500000-0x000002500000 : "rootfs" [ 22.191025] 0x000002500000-0x000010000000 : "data" [ 22.197176] libphy: Fixed MDIO Bus: probed [ 22.213951] libphy: orion_mdio_bus: probed [ 22.218240] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 23.297450] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:10:75:26:65:ae [ 23.306443] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 23.313001] ehci-pci: EHCI PCI platform driver [ 23.317547] ehci-orion: EHCI orion driver [ 23.321653] orion-ehci orion-ehci.0: EHCI Host Controller [ 23.327127] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 [ 23.334852] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000 [ 23.356362] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00 [ 23.362498] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 23.369344] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 23.376619] usb usb1: Product: EHCI Host Controller [ 23.381520] usb usb1: Manufacturer: Linux 3.16.0-kirkwood-tld-2 ehci_hcd [ 23.388267] usb usb1: SerialNumber: orion-ehci.0 [ 23.393650] hub 1-0:1.0: USB hub found [ 23.397499] hub 1-0:1.0: 1 port detected [ 23.402311] mousedev: PS/2 mouse device common for all mice [ 23.716383] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 23.944114] usb 1-1: New USB device found, idVendor=058f, idProduct=6387 [ 23.950874] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 23.958070] usb 1-1: Product: Mass Storage [ 23.962184] usb 1-1: Manufacturer: Generic [ 23.966299] usb 1-1: SerialNumber: 065414A6 [ 24.416355] rtc-mv rtc-mv: internal RTC not ticking [ 24.421447] i2c /dev entries driver [ 24.426765] hidraw: raw HID events driver (C) Jiri Kosina [ 24.432547] drop_monitor: Initializing network drop monitor service [ 24.439106] TCP: cubic registered [ 24.442447] NET: Registered protocol family 17 [ 24.447080] Key type dns_resolver registered [ 24.452105] registered taskstats version 1 [ 24.457253] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 24.465431] Freeing unused kernel memory: 256K (c0725000 - c0765000) Loading, please wait... [ 24.547301] udevd[55]: starting version 175 [ 24.722850] SCSI subsystem initialized [ 24.768293] usb-storage 1-1:1.0: USB Mass Storage device detected [ 24.784262] sata_mv sata_mv.0: cannot get optional clkdev [ 24.816169] scsi0 : usb-storage 1-1:1.0 [ 24.820268] sata_mv sata_mv.0: slots 32 ports 2 [ 24.836109] usbcore: registered new interface driver usb-storage [ 24.860866] scsi1 : sata_mv [ 24.867852] usbcore: registered new interface driver uas [ 24.882622] scsi2 : sata_mv [ 24.885778] ata1: SATA max UDMA/133 irq 21 [ 24.911416] ata2: SATA max UDMA/133 irq 21 [ 25.256374] ata1: SATA link down (SStatus 0 SControl F300) [ 25.626888] ata2: SATA link down (SStatus 0 SControl F300) [ 25.828598] scsi 0:0:0:0: Direct-Access Generic Flash Disk 8.07 PQ: 0 ANSI: 2 [ 25.868684] sd 0:0:0:0: [sda] 7989248 512-byte logical blocks: (4.09 GB/3.80 GiB) [ 25.876773] sd 0:0:0:0: [sda] Write Protect is off [ 25.882017] sd 0:0:0:0: [sda] No Caching mode page found [ 25.887407] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 25.937149] sda: sda1 [ 25.942398] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 25.959586] sd 0:0:0:0: Attached scsi generic sg0 type 0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. mount: mounting /dev/sda1 on /root failed: Invalid argument Begin: Running /scripts/local-bottom ... done. done. Begin: Running /scripts/init-bottom ... mount: mounting /dev on /root/dev failed: No such file or directory done. Target filesystem doesn't have requested /sbin/init. No init found. Try passing init= bootarg. modprobe: module i8042 not found in modules.dep [ 35.845694] uhci_hcd: USB Universal Host Controller Interface driver [ 35.860027] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 35.874891] usbcore: registered new interface driver usbhid [ 35.880626] usbhid: USB HID core driver
Re: Goflex net bad blocks and no boot. October 24, 2014 05:18AM |
Admin Registered: 13 years ago Posts: 18,555 |
printenvPlease post this u-boot envs listing here.
Re: Goflex net bad blocks and no boot. October 24, 2014 05:34AM |
Registered: 9 years ago Posts: 64 |
U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:35:50) Seagate GoFlex Net SoC: Kirkwood 88F6281_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 88E1116 Initialized on egiga0 Using egiga0 device Abort ping failed; host 192.168.178.26 is not alive Hit any key to stop autoboot: 0 GoFlexNet> printenv arcNumber=3089 baudrate=115200 bootcmd=run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; reset bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot; bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot; bootdelay=10 console=ttyS0,115200 device=0:1 ethact=egiga0 ethaddr=00:10:75:26:65:AE if_netconsole=ping $serverip ipaddr=192.168.178.35 led_error=orange blinking led_exit=green off led_init=green blinking mainlineLinux=yes mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi mmc_init=mmc rescan mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd mmc_root=/dev/mmcblk0p1 mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) partition=nand0,2 preboot=run if_netconsole start_netconsole preboot_nc=run if_netconsole start_netconsole rootdelay=10 rootfstype=ext3 sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi sata_init=ide reset sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd sata_root=/dev/sda1 serverip=192.168.178.26 set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_init=usb start usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd usb_root=/dev/sda1 Environment size: 2253/131068 bytes GoFlexNet> printenv
Re: Goflex net bad blocks and no boot. October 24, 2014 05:54AM |
Admin Registered: 13 years ago Posts: 18,555 |
preboot=run if_netconsole start_netconsoleSince you have serial console, there is no need for this, so you can temporarily turn it off (in case you want to use it in the future):
setenv preboot_nc 'run if_netconsole start_netconsole' setenv preboot
rootfstype=ext3
setenv rootfstype
Re: Goflex net bad blocks and no boot. October 24, 2014 06:22AM |
Registered: 9 years ago Posts: 64 |
tune2fs -j /dev/sdc1
Re: Goflex net bad blocks and no boot. October 24, 2014 09:47AM |
Registered: 9 years ago Posts: 70 |
Re: Goflex net bad blocks and no boot. October 24, 2014 11:27AM |
Registered: 9 years ago Posts: 64 |