No USB Boot / Getting Kernel Messages in NC February 24, 2015 11:46AM |
Registered: 9 years ago Posts: 6 |
usb_custom_params 'loglevel=7 netconsole=6666@192.168.1.10/eth0,6666@192.169.1.50/' set_bootargs_usb 'setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts $usb_custom_params'
baudrate=115200 bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot; bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot; bootdelay=10 console=ttyS0,115200 device=0:1 ethact=egiga0 led_error=orange blinking led_exit=green off led_init=green blinking mainlineLinux=yes mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi mmc_init=mmc rescan mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd mmc_root=/dev/mmcblk0p1 mtdids=nand0=orion_nand partition=nand0,2 preboot_nc=run if_netconsole start_netconsole rootdelay=10 sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi sata_init=ide reset sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd sata_root=/dev/sda1 set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts stderr=serial stdin=serial stdout=serial usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_init=usb start usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd machid=f78 arcNumber=3960 mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) rootfstype=ext3 ethaddr=00:25:31:04:e2:38 serverip=192.168.1.50 bootcmd=run bootcmd_uenv; run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; run bootcmd_pogo; reset bootcmd_pogo=if ubi part root 2048 && ubifsmount ubi:rootfs && ubifsload 0x800000 uboot.mtd0.dockstar.original.kwb ; then go 0x800200; fi devices=usb mmc ide bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi uenv_import=echo importing envs ...; env import -t 0x810000 uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x810000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; ipaddr=192.168.1.10 usb_root=LABEL=rootfs set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts $usb_custom_params if_netconsole=ping $serverip start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; preboot=run if_netconsole start_netconsole usb_custom_params=loglevel=7 netconsole=6666@192.168.1.10/eth0,6666@192.169.1.50/
U-Boot 2014.07-tld-2 (Sep 19 2014 - 16:13:05) Pogoplug V4 gcc (Debian 4.6.3-14) 4.6.3 GNU ld (GNU Binutils for Debian) 2.22 Hit any key to stop autoboot: 0 (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Reset IDE: ide_preinit failed Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 21 15632694 0001b1cd-01 83 Boot loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** no IDE devices available (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found 2822232 bytes read in 373 ms (7.2 MiB/s) 6114335 bytes read in 459 ms (12.7 MiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.17.0-kirkwood-tld-1 Created: 2014-10-25 3:29:23 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2822168 Bytes = 2.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-3.17.0-kirkwood-tld-1 Created: 2014-10-25 3:29:30 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6114271 Bytes = 5.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ...
Re: No USB Boot / Getting Kernel Messages in NC February 24, 2015 02:14PM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: No USB Boot / Getting Kernel Messages in NC February 24, 2015 05:32PM |
Registered: 9 years ago Posts: 6 |
Re: No USB Boot / Getting Kernel Messages in NC February 24, 2015 05:49PM |
Admin Registered: 13 years ago Posts: 18,495 |
cat /lib/udev/rules.d/75-persistent-net-generator.rules | grep KERNEL cat /etc/udev/rules.d/70-persistent-net.rules