Help - Why no serial console output after "Starting kernel..."? April 11, 2015 12:39PM |
Registered: 11 years ago Posts: 165 |
U-Boot 2013.10-tld-4 (Sep 08 2014 - 19:43:38) for OXNAS DRAM: 128 MiB NAND: 128 MiB In: serial Out: serial Err: serial Net: Led: GREEN mii0 Main Loop Waiting for PHY auto negotiation to complete.... TIMEOUT! ENET Speed is 10 Mbps - HALF duplex connection Using mii0 device ping failed; host 192.168.100.160 is not alive Hit any key to stop autoboot: 0 OX820> printenv autoload=no baudrate=115200 bootargs=console=ttyS0,115200n8 bootcmd=run dt_bootcmd_usb bootdelay=10 console=console=ttyS0,115200n8 dt_bootcmd_usb=usb start; run dt_usb_bootcmd; usb stop; reset dt_bootm=bootm $uimage_addr $uinitrd_addr $dtb_addr dt_load_dtb=ext2load usb 0:1 $dtb_addr $fdt_file dt_load_initrd=ext2load usb 0:1 $uinitrd_addr /boot/uInitrd dt_load_uimage=ext2load usb 0:1 $uimage_addr /boot/uImage dt_usb_boot=run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm dt_usb_bootcmd=run usb_set_bootargs; run dt_usb_boot dtb_addr=0x62c00000 ethact=mii0 ethaddr=00:25:31:02:xx:xx fdt_file=/boot/dts/ox820-pogoplug-pro.dtb if_netconsole=ping $serverip ipaddr=192.168.100.10 mtdids=nand0=41000000.nand mtdparts=mtdparts=41000000.nand:14m(boot),-(data) preboot=run preboot_nc preboot_nc=run if_netconsole start_netconsole serverip=192.168.100.160 setenv=fdt_file /boot/dts/ox820-pogoplug-classic.dtb start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version stderr=serial stdin=serial stdout=serial uimage_addr=0x60500000 uinitrd_addr=0x60e00000 usb_device=0:1 usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=/dev/sda1 rootdelay=10 Environment size: 1296/131068 bytes OX820> boot (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found 4170064 bytes read in 455 ms (8.7 MiB/s) 1975075 bytes read in 345 ms (5.5 MiB/s) 7029 bytes read in 237 ms (28.3 KiB/s) ## Booting kernel from Legacy Image at 60500000 ... Image Name: Linux-3.18.5-oxnas-tld-1 Created: 2015-04-08 3:59:57 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4170000 Bytes = 4 MiB Load Address: 60008000 Entry Point: 60008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 60e00000 ... Image Name: initramfs-3.18.5-oxnas-tld-1 Created: 2015-04-08 4:00:00 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 1975011 Bytes = 1.9 MiB Load Address: 60000000 Entry Point: 60000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 62c00000 Booting using the fdt blob at 0x62c00000 Loading Kernel Image ... OK Loading Ramdisk to 67c46000, end 67e282e3 ... OK Loading Device Tree to 67c41000, end 67c45b74 ... OK Led: GREEN Starting kernel ... Uncompressing Linux... done, booting the kernel.
Re: Help - Why no serial console output after "Starting kernel..."? April 11, 2015 12:45PM |
Registered: 11 years ago Posts: 165 |