Welcome! Log In Create A New Profile

Advanced

can this device run "Bodhi's U-boot"

Posted by Gravelrash 
can this device run "Bodhi's U-boot"
October 23, 2015 06:06AM
HP T5325

please see below screen output mainly in relation to the S.O.C. statement


_ _ .____
| |_| | | _ \
| _ | | (_))
| |-| | | |
|_| |_| |_| ..
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
** BOARD: DB-88F6281A-BP LE

U-Boot 1.1.4 (Jan 8 2010 - 14:03:56) MIC version : 3.4.19-16

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD4E0


Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz


DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM CS[1] base 0x10000000 size 256MB
DRAM Total size 512MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
[1024kB@f8000000] Flash: 1 MB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: SM22 Firm: I052 Ser#: (03)5526888-20080228
Type: Hard Disk
Capacity: 463.6 MB = 0.4 GB (949536 x 512)


2148560 bytes read
Checking Button Status: off
Checking GotoWOL Status: off
## Booting image at 00200000 ...
Image Name: Linux-2.6.22.18-1-armel
Created: 2009-10-08 13:56:48 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2148496 Bytes = 2 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux.............................................................
............................................................................ done, booting the kernel

============================
Breaking stuff since 1994 :-)
============================
Re: can this device run "Bodhi's U-boot"
October 23, 2015 12:18PM
Gravelrash,

> Soc: 88F6281 A0 (DDR2)
> CPU running @ 1200Mhz L2 running @ 400Mhz
> SysClock = 400Mhz , TClock = 200Mhz

Most definitely. Try booting UART serial console using the sheevaplug or dockstar u-boot image. If you can use kwboot to boot with UART then it's safe to flash.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: can this device run "Bodhi's U-boot"
October 23, 2015 12:38PM
Thanks - i will give it a go in a while
Author:

Your Email:


Subject:


Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: