Iomega ix4-200d U-boot needed
Posted by Reto
|
Re: Iomega ix4-200d U-boot needed August 24, 2022 06:56PM |
Registered: 1 year ago Posts: 52 |
Good catch, I hadnt noticed that only 2 of the 4 disks are being detected.
I ran parted and can only see two but then this popped up in the console:
Im pretty sure I see the same in stock u-boot too for ata3 and 4 but they are detected and working there
I ran parted and can only see two but then this popped up in the console:
Welcome to GNU Parted! Type 'help' to view a list of commands. (parted) print all Model: SanDisk Cruzer Orbit (scsi) Disk /dev/sda: 32.0GB Sector size (logical/physical): 512B/512B Partition Table: msdos Disk Flags: Number Start End Size Type File system Flags 1 1049kB 32.0GB 32.0GB primary ext2 Model: ATA ST6000NM021A-2R7 (scsi) Disk /dev/sdb: 6001GB Sector size (logical/physical): 512B/4096B Partition Table: gpt Disk Flags: Number Start End Size File system Name Flags 1 1049kB 6001GB 6001GB primary Model: ATA ST6000NM021A-2R7 (scsi) Disk /dev/sdc: 6001GB Sector size (logical/physical): 512B/4096B Partition Table: gpt Disk Flags: Number Start End Size File system Name Flags 1 1049kB 6001GB 6001GB ext4 primary (parted) [ 2871.907134][ T152] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2876.964870][ T152] ata3.00: qc timeout (cmd 0xec) [ 2876.969754][ T152] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 2876.979539][ T152] ata3.00: revalidation failed (errno=-5) [ 2877.317131][ T152] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2887.524850][ T152] ata3.00: qc timeout (cmd 0xec) [ 2887.529735][ T152] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 2887.539233][ T152] ata3.00: revalidation failed (errno=-5) [ 2887.546412][ T152] ata3: limiting SATA link speed to 1.5 Gbps [ 2887.877103][ T152] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 2887.889423][ T152] ata3.00: configured for UDMA/133
Im pretty sure I see the same in stock u-boot too for ata3 and 4 but they are detected and working there
|
Re: Iomega ix4-200d U-boot needed August 24, 2022 06:57PM |
Admin Registered: 13 years ago Posts: 18,543 |
Here is the new test version. This has substantial change, so cross your finger :)
uboot.2022.10-rc3-tld-0.2.ix4_200d.mtd0.kwb.
Try kwboot and
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
uboot.2022.10-rc3-tld-0.2.ix4_200d.mtd0.kwb.
Try kwboot and
sata init sata info sata part
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Iomega ix4-200d U-boot needed August 24, 2022 06:59PM |
Admin Registered: 13 years ago Posts: 18,543 |
Quote
Im pretty sure I see the same in stock u-boot too for ata3 and 4 but they are detected and working there
Let see if the version I just uploaded above is better!
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Iomega ix4-200d U-boot needed August 24, 2022 07:08PM |
Registered: 1 year ago Posts: 52 |
Still only two disks but again, booting fine with new u-boot:
Edited 1 time(s). Last edit at 08/24/2022 07:12PM by CodeJACK.
=> setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts'
=> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage.orig'
=> setenv load_uinitrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd'
=> setenv load_dtb 'ext2load usb 0:1 0x2c00000 /boot/dts/kirkwood-iomega_ix4_200d.dtb'
=> setenv usb_boot 'usb reset; run set_bootargs; run load_uimage; run load_uinitrd; run load_dtb; bootm 0x800000 0x1100000 0x2c00000'
=> run usb_boot
resetting USB...
Bus ehci@50000: USB EHCI 1.00
scanning bus ehci@50000 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
5729264 bytes read in 247 ms (22.1 MiB/s)
11127733 bytes read in 470 ms (22.6 MiB/s)
9274 bytes read in 20 ms (452.1 KiB/s)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: linux-5.18.6-kirkwood-tld-1.patc
Created: 2022-08-24 23:03:37 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5729200 Bytes = 5.5 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-5.18.6-kirkwood-tld-1
Created: 2022-08-03 18:44:18 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 11127669 Bytes = 10.6 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 02c00000
Booting using the fdt blob at 0x2c00000
Loading Kernel Image
Loading Ramdisk to 1f0b4000, end 1fb50b75 ... OK
Loading Device Tree to 0fffa000, end 0ffff439 ... OK
Starting kernel ...
root@debian:~# dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.18.6-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1.0 PREEMPT Fri Jun 24 15:26:02 PDT 2022 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: Iomega ix4-200d [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x100000@0x0(u-boot),0x0500000@0x100000(uImage),-(rootfs) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000] Memory: 488452K/524288K available (11264K kernel code, 1633K rwdata, 4936K rodata, 1024K init, 300K bss, 35836K reserved, 0K cma-reserved) [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000002] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000058] Switching to timer-based delay loop, resolution 5ns [ 0.001587] Console: colour dummy device 80x30 [ 0.001661] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.001705] pid_max: default: 32768 minimum: 301 [ 0.002376] LSM: Security Framework initializing [ 0.002803] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.002856] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.004738] CPU: Testing write buffer coherency: ok [ 0.007776] cblist_init_generic: Setting adjustable number of callback queues. [ 0.007814] cblist_init_generic: Setting shift to 0 and lim to 1. [ 0.008213] cblist_init_generic: Setting shift to 0 and lim to 1. [ 0.008700] Setting up static identity map for 0x100000 - 0x100058 [ 0.009030] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.009433] rcu: Hierarchical SRCU implementation. [ 0.011300] devtmpfs: initialized [ 0.017713] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.017771] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.056182] prandom32: self test passed (less than 6 bits correlated) [ 0.056229] prandom: seed boundary self test passed [ 0.060538] prandom: 100 self tests passed [ 0.060568] pinctrl core: initialized pinctrl subsystem [ 0.063088] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.063978] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.065256] audit: initializing netlink subsys (disabled) [ 0.067311] thermal_sys: Registered thermal governor 'step_wise' [ 0.067754] audit: type=2000 audit(0.060:1): state=initialized audit_enabled=0 res=1 [ 0.067919] cpuidle: using governor ladder [ 0.068016] cpuidle: using governor menu [ 0.068569] Feroceon L2: Enabling L2 [ 0.068625] Feroceon L2: Cache support initialised. [ 0.079015] No ATAGs? [ 0.260295] raid6: int32x8 gen() 108 MB/s [ 0.430219] raid6: int32x4 gen() 95 MB/s [ 0.600181] raid6: int32x2 gen() 138 MB/s [ 0.770401] raid6: int32x1 gen() 99 MB/s [ 0.770425] raid6: using algorithm int32x2 gen() 138 MB/s [ 0.940127] raid6: .... xor() 81 MB/s, rmw enabled [ 0.940147] raid6: using intx1 recovery algorithm [ 0.941012] SCSI subsystem initialized [ 0.941367] libata version 3.00 loaded. [ 0.941699] usbcore: registered new interface driver usbfs [ 0.941814] usbcore: registered new interface driver hub [ 0.941879] usbcore: registered new device driver usb [ 0.942165] pps_core: LinuxPPS API ver. 1 registered [ 0.942184] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.942222] PTP clock support registered [ 0.943988] vgaarb: loaded [ 0.944766] clocksource: Switched to clocksource orion_clocksource [ 1.081709] VFS: Disk quotas dquot_6.6.0 [ 1.081832] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.106960] NET: Registered PF_INET protocol family [ 1.107321] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.115361] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 1.115616] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 1.115658] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 1.115734] TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 1.115796] TCP: Hash tables configured (established 4096 bind 4096) [ 1.116106] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.116212] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 1.116266] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 1.116601] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 1.117663] RPC: Registered named UNIX socket transport module. [ 1.117689] RPC: Registered udp transport module. [ 1.117702] RPC: Registered tcp transport module. [ 1.117714] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.117733] PCI: CLS 0 bytes, default 32 [ 1.117921] NetWinder Floating Point Emulator V0.97 (double precision) [ 1.125197] Trying to unpack rootfs image as initramfs... [ 3.084829] Freeing initrd memory: 10868K [ 3.845817] Initialise system trusted keyrings [ 3.845916] Key type blacklist registered [ 3.846308] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 3.846487] zbud: loaded [ 3.848810] NFS: Registering the id_resolver key type [ 3.848914] Key type id_resolver registered [ 3.848932] Key type id_legacy registered [ 3.848999] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 3.849027] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 3.849044] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 3.849484] jffs2: version 2.2. (NAND) (SUMMARY) \xc2\xa9 2001-2006 Red Hat, Inc. [ 3.850017] fuse: init (API version 7.36) [ 3.850496] orangefs_debugfs_init: called with debug mask: :none: :0: [ 3.850820] orangefs_init: module version upstream loaded [ 3.850842] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled [ 3.950085] xor: measuring software checksum speed [ 3.959052] arm4regs : 1112 MB/sec [ 3.973825] 8regs : 667 MB/sec [ 3.984253] 32regs : 947 MB/sec [ 3.984272] xor: using function: arm4regs (1112 MB/sec) [ 3.984294] async_tx: api initialized (async) [ 3.984316] Key type asymmetric registered [ 3.984331] Asymmetric key parser 'x509' registered [ 4.021936] alg: self-tests for CTR-KDF (hmac(sha256)) passed [ 4.022194] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 4.022363] io scheduler bfq registered [ 4.211925] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 4.214321] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges: [ 4.214379] mvebu-pcie mbus@f1000000:pcie@82000000: Parsing ranges property... [ 4.214422] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000 [ 4.214473] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 4.214510] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 4.214623] mvebu-pcie mbus@f1000000:pcie@82000000: pcie0.0: legacy INTx interrupts cannot be masked individually, /mbus@f1000000/pcie@82000000/pcie@1,0 does not contain intx interrupt [ 4.215184] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 4.215214] pci_bus 0000:00: root bus resource [bus 00-ff] [ 4.215241] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff]) [ 4.215265] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 4.215287] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 4.215309] pci_bus 0000:00: scanning bus [ 4.215407] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400 [ 4.215760] pci 0000:00:01.0: vgaarb: pci_notify [ 4.216632] pci_bus 0000:00: fixups for bus [ 4.216653] PCI: bus0: Fast back to back transfers disabled [ 4.216677] pci 0000:00:01.0: scanning [bus 00-00] behind bridge, pass 0 [ 4.216694] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 4.216722] pci 0000:00:01.0: scanning [bus 00-00] behind bridge, pass 1 [ 4.216922] pci_bus 0000:01: scanning bus [ 4.217003] pci 0000:01:00.0: [11ab:6121] type 00 class 0x01018f [ 4.217046] pci 0000:01:00.0: reg 0x10: [io 0x8000-0x8007] [ 4.217076] pci 0000:01:00.0: reg 0x14: [io 0x8040-0x8043] [ 4.217105] pci 0000:01:00.0: reg 0x18: [io 0x8200-0x8207] [ 4.217133] pci 0000:01:00.0: reg 0x1c: [io 0x8800-0x8803] [ 4.217160] pci 0000:01:00.0: reg 0x20: [io 0x900000-0x90000f] [ 4.217188] pci 0000:01:00.0: reg 0x24: [mem 0x00800000-0x008003ff] [ 4.217294] pci 0000:01:00.0: supports D1 [ 4.217314] pci 0000:01:00.0: PME# supported from D0 D1 D3hot [ 4.217337] pci 0000:01:00.0: PME# disabled [ 4.217627] pci 0000:01:00.0: vgaarb: pci_notify [ 4.217683] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 4.218510] pci_bus 0000:01: fixups for bus [ 4.218528] PCI: bus1: Fast back to back transfers disabled [ 4.218546] pci_bus 0000:01: bus scan returning with max=01 [ 4.218562] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 4.218590] pci_bus 0000:00: bus scan returning with max=01 [ 4.218625] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 4.218652] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff] [ 4.218683] pci 0000:01:00.0: BAR 5: assigned [mem 0xe0000000-0xe00003ff] [ 4.218712] pci 0000:01:00.0: BAR 4: assigned [io 0x10000-0x1000f] [ 4.218739] pci 0000:01:00.0: BAR 0: assigned [io 0x10010-0x10017] [ 4.218764] pci 0000:01:00.0: BAR 2: assigned [io 0x10018-0x1001f] [ 4.218789] pci 0000:01:00.0: BAR 1: assigned [io 0x10020-0x10023] [ 4.218815] pci 0000:01:00.0: BAR 3: assigned [io 0x10024-0x10027] [ 4.218842] pci 0000:00:01.0: PCI bridge to [bus 01] [ 4.218863] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff] [ 4.218894] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 4.218996] pcieport 0000:00:01.0: vgaarb: pci_notify [ 4.219032] pcieport 0000:00:01.0: assign IRQ: got 0 [ 4.219058] pcieport 0000:00:01.0: enabling device (0140 -> 0143) [ 4.219090] pcieport 0000:00:01.0: enabling bus mastering [ 4.219122] pcieport 0000:00:01.0: vgaarb: pci_notify [ 4.219750] mv_xor f1060800.xor: Marvell shared XOR driver [ 4.275909] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 4.279882] mv_xor f1060900.xor: Marvell shared XOR driver [ 4.335974] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 4.340273] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 4.341964] printk: console [ttyS0] disabled [ 4.342074] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 5.473946] printk: console [ttyS0] enabled [ 5.489312] loop: module loaded [ 5.493529] sata_mv f1080000.sata: version 1.28 [ 5.494116] sata_mv f1080000.sata: slots 32 ports 2 [ 5.504138] scsi host0: sata_mv [ 5.509036] scsi host1: sata_mv [ 5.513234] ata1: SATA max UDMA/133 irq 33 [ 5.518117] ata2: SATA max UDMA/133 irq 33 [ 5.523947] nand: device found, Manufacturer ID: 0xec, Chip ID: 0x75 [ 5.531128] nand: Samsung NAND 32MiB 3,3V 8-bit [ 5.536411] nand: 32 MiB, SLC, erase size: 16 KiB, page size: 512, OOB size: 16 [ 5.544487] Scanning device for bad blocks [ 5.856313] ata1: SATA link down (SStatus 0 SControl F300) [ 5.903936] 3 cmdlinepart partitions found on MTD device orion_nand [ 5.910959] Creating 3 MTD partitions on "orion_nand": [ 5.916883] 0x000000000000-0x000000100000 : "u-boot" [ 5.923266] 0x000000100000-0x000000600000 : "uImage" [ 5.929758] 0x000000600000-0x000002000000 : "rootfs" [ 5.937543] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 5.946159] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 5.989868] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 6.206449] ata2: SATA link down (SStatus 0 SControl F300) [ 6.755977] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:b8:13:1d:15 [ 7.525947] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:d0:b8:13:1d:16 [ 7.535646] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.542992] ehci-pci: EHCI PCI platform driver [ 7.548258] ehci-orion: EHCI orion driver [ 7.553251] orion-ehci f1050000.ehci: EHCI Host Controller [ 7.559583] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 7.568240] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 7.604806] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 7.611864] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.18 [ 7.620909] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.628897] usb usb1: Product: EHCI Host Controller [ 7.634500] usb usb1: Manufacturer: Linux 5.18.6-kirkwood-tld-1 ehci_hcd [ 7.641964] usb usb1: SerialNumber: f1050000.ehci [ 7.648213] hub 1-0:1.0: USB hub found [ 7.652734] hub 1-0:1.0: 1 port detected [ 7.658379] usbcore: registered new interface driver usb-storage [ 7.665656] mousedev: PS/2 mouse device common for all mice [ 7.673141] rtc-mv f1010300.rtc: registered as rtc0 [ 7.678856] rtc-mv f1010300.rtc: setting system clock to 2022-08-25T00:05:24 UTC (1661385924) [ 7.688523] i2c_dev: i2c /dev entries driver [ 7.695315] device-mapper: uevent: version 1.0.3 [ 7.701047] device-mapper: ioctl: 4.46.0-ioctl (2022-02-22) initialised: dm-devel@redhat.com [ 7.710919] device-mapper: multipath round-robin: version 1.2.0 loaded [ 7.718256] device-mapper: multipath queue-length: version 0.2.0 loaded [ 7.725638] device-mapper: multipath service-time: version 0.3.0 loaded [ 7.733082] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 7.739934] device-mapper: raid: Loading target version 1.15.1 [ 7.747499] hid: raw HID events driver (C) Jiri Kosina [ 7.753742] drop_monitor: Initializing network drop monitor service [ 7.761421] NET: Registered PF_INET6 protocol family [ 7.769289] Segment Routing with IPv6 [ 7.773679] RPL Segment Routing with IPv6 [ 7.778600] In-situ OAM (IOAM) with IPv6 [ 7.783373] NET: Registered PF_PACKET protocol family [ 7.789546] Key type dns_resolver registered [ 7.795477] registered taskstats version 1 [ 7.800308] Loading compiled-in X.509 certificates [ 7.807142] zswap: loaded using pool lzo/zbud [ 7.812943] Key type ._fscrypt registered [ 7.817772] Key type .fscrypt registered [ 7.822424] Key type fscrypt-provisioning registered [ 7.834088] Key type big_key registered [ 7.870711] Key type encrypted registered [ 7.944848] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 7.975829] "cryptomgr_test" (105) uses obsolete ecb(arc4) skcipher [ 8.146623] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=77.63 [ 8.164787] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 8.172665] usb 1-1: Product: USB2.0 Hub [ 8.195847] hub 1-1:1.0: USB hub found [ 8.204800] hub 1-1:1.0: 4 ports detected [ 8.534798] usb 1-1.2: new high-speed USB device number 3 using orion-ehci [ 8.695744] usb 1-1.2: New USB device found, idVendor=0781, idProduct=557c, bcdDevice= 1.27 [ 8.714788] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 8.722845] usb 1-1.2: Product: Cruzer Orbit [ 8.744786] usb 1-1.2: Manufacturer: SanDisk [ 8.749780] usb 1-1.2: SerialNumber: 4C530012311126108485 [ 8.765751] usb-storage 1-1.2:1.0: USB Mass Storage device detected [ 8.785350] scsi host2: usb-storage 1-1.2:1.0 [ 9.848706] scsi 2:0:0:0: Direct-Access SanDisk Cruzer Orbit 1.27 PQ: 0 ANSI: 6 [ 9.874829] sd 2:0:0:0: [sda] 62530624 512-byte logical blocks: (32.0 GB/29.8 GiB) [ 9.890393] sd 2:0:0:0: [sda] Write Protect is off [ 9.904793] sd 2:0:0:0: [sda] Mode Sense: 43 00 00 00 [ 9.907770] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 9.962535] sda: sda1 [ 9.997650] sd 2:0:0:0: [sda] Attached SCSI removable disk [ 12.526977] Freeing unused kernel image (initmem) memory: 1024K [ 12.545712] Checked W+X mappings: passed, no W+X pages found [ 12.552123] Run /init as init process [ 12.556566] with arguments: [ 12.556579] /init [ 12.556588] with environment: [ 12.556595] HOME=/ [ 12.556603] TERM=linux [ 13.532069] ahci 0000:01:00.0: vgaarb: pci_notify [ 13.532210] ahci 0000:01:00.0: assign IRQ: got 38 [ 13.532247] ahci 0000:01:00.0: version 3.0 [ 13.532281] pci 0000:00:01.0: enabling bus mastering [ 13.532398] ahci 0000:01:00.0: Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this. [ 13.606188] ahci 0000:01:00.0: controller can't do NCQ, turning off CAP_NCQ [ 13.613910] ahci 0000:01:00.0: controller can't do PMP, turning off CAP_PMP [ 13.684453] ahci 0000:01:00.0: masking port_map 0x7 -> 0x3 [ 13.717867] ahci 0000:01:00.0: SSS flag set, parallel bus scan disabled [ 13.725517] usbcore: registered new interface driver uas [ 13.758218] ahci 0000:01:00.0: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x3 impl IDE mode [ 13.806303] ahci 0000:01:00.0: flags: 64bit stag led slum part [ 13.865599] scsi host3: ahci [ 13.896631] scsi host4: ahci [ 13.927842] scsi host5: ahci [ 13.947421] ata3: SATA max UDMA/133 abar m1024@0xe0000000 port 0xe0000100 irq 38 [ 13.999866] ata4: SATA max UDMA/133 abar m1024@0xe0000000 port 0xe0000180 irq 38 [ 14.053563] ata5: DUMMY [ 14.066466] ahci 0000:01:00.0: vgaarb: pci_notify [ 14.396468] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 14.405231] ata3.00: ATA-11: ST6000NM021A-2R7101, SN03, max UDMA/133 [ 14.412419] ata3.00: 11721045168 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 14.422897] ata3.00: configured for UDMA/133 [ 14.438483] scsi 3:0:0:0: Direct-Access ATA ST6000NM021A-2R7 SN03 PQ: 0 ANSI: 5 [ 14.450316] sd 3:0:0:0: [sdb] 11721045168 512-byte logical blocks: (6.00 TB/5.46 TiB) [ 14.461101] sd 3:0:0:0: [sdb] 4096-byte physical blocks [ 14.467324] sd 3:0:0:0: [sdb] Write Protect is off [ 14.472938] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 14.473093] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 14.777856] sdb: sdb1 [ 14.784292] sd 3:0:0:0: [sdb] Attached SCSI disk [ 14.794888] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 14.803711] ata4.00: ATA-11: ST6000NM021A-2R7101, SN03, max UDMA/133 [ 14.810942] ata4.00: 11721045168 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 14.821416] ata4.00: configured for UDMA/133 [ 14.836991] scsi 4:0:0:0: Direct-Access ATA ST6000NM021A-2R7 SN03 PQ: 0 ANSI: 5 [ 14.848876] sd 4:0:0:0: [sdc] 11721045168 512-byte logical blocks: (6.00 TB/5.46 TiB) [ 14.859730] sd 4:0:0:0: [sdc] 4096-byte physical blocks [ 14.866016] sd 4:0:0:0: [sdc] Write Protect is off [ 14.871631] sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00 [ 14.871783] sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 14.922194] sdc: sdc1 [ 14.928657] sd 4:0:0:0: [sdc] Attached SCSI disk [ 15.511387] Btrfs loaded, crc32c=crc32c-generic, zoned=no, fsverity=no [ 26.877705] systemd[1]: Inserted module 'autofs4' [ 26.977862] systemd[1]: systemd 247.3-7 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 27.002102] systemd[1]: Detected architecture arm. [ 27.047017] systemd[1]: Set hostname to <debian>. [ 28.594837] random: crng init done [ 29.690133] systemd[1]: Queued start job for default target Graphical Interface. [ 29.701693] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 29.715002] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 29.726591] systemd[1]: Created slice system-getty.slice. [ 29.766398] systemd[1]: Created slice system-modprobe.slice. [ 29.806352] systemd[1]: Created slice system-serial\x2dgetty.slice. [ 29.846011] systemd[1]: Created slice User and Session Slice. [ 29.885613] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ 29.925510] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 29.966574] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [ 30.005449] systemd[1]: Reached target Local Encrypted Volumes. [ 30.045861] systemd[1]: Reached target Paths. [ 30.085560] systemd[1]: Reached target Slices. [ 30.125311] systemd[1]: Reached target Swap. [ 30.155250] systemd[1]: Reached target System Time Set. [ 30.196455] systemd[1]: Listening on Device-mapper event daemon FIFOs. [ 30.235912] systemd[1]: Listening on LVM2 poll daemon socket. [ 30.276246] systemd[1]: Listening on RPCbind Server Activation Socket. [ 30.317413] systemd[1]: Listening on Syslog Socket. [ 30.357065] systemd[1]: Listening on fsck to fsckd communication Socket. [ 30.395655] systemd[1]: Listening on initctl Compatibility Named Pipe. [ 30.436512] systemd[1]: Listening on Journal Audit Socket. [ 30.476044] systemd[1]: Listening on Journal Socket (/dev/log). [ 30.516186] systemd[1]: Listening on Journal Socket. [ 30.557527] systemd[1]: Listening on Network Service Netlink Socket. [ 30.596269] systemd[1]: Listening on udev Control Socket. [ 30.635987] systemd[1]: Listening on udev Kernel Socket. [ 30.676110] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 30.690541] systemd[1]: Mounting POSIX Message Queue File System... [ 30.718588] systemd[1]: Mounting RPC Pipe File System... [ 30.770117] systemd[1]: Mounting Kernel Debug File System... [ 30.820031] systemd[1]: Mounting Kernel Trace File System... [ 30.865605] systemd[1]: Condition check resulted in Kernel Module supporting RPCSEC_GSS being skipped. [ 30.876916] systemd[1]: Finished Availability of block devices. [ 30.922298] systemd[1]: Starting Create list of static device nodes for the current kernel... [ 30.980101] systemd[1]: Starting Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling... [ 31.040658] systemd[1]: Starting Load Kernel Module configfs... [ 31.110515] systemd[1]: Starting Load Kernel Module drm... [ 31.170641] systemd[1]: Starting Load Kernel Module fuse... [ 31.225456] systemd[1]: Condition check resulted in OpenVSwitch configuration for cleanup being skipped. [ 31.258145] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 31.268635] systemd[1]: Condition check resulted in File System Check on Root Device being skipped. [ 31.296376] systemd[1]: Starting Journal Service... [ 31.336666] systemd[1]: Starting Load Kernel Modules... [ 31.400061] systemd[1]: Starting Remount Root and Kernel File Systems... [ 31.480119] systemd[1]: Starting Coldplug All udev Devices... [ 31.601625] systemd[1]: Mounted POSIX Message Queue File System. [ 31.666001] systemd[1]: Mounted RPC Pipe File System. [ 31.706143] systemd[1]: Mounted Kernel Debug File System. [ 31.726158] systemd[1]: Mounted Kernel Trace File System. [ 31.758528] ext2 filesystem being remounted at / supports timestamps until 2038 (0x7fffffff) [ 31.768145] systemd[1]: Finished Create list of static device nodes for the current kernel. [ 31.864982] systemd[1]: Finished Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling. [ 31.927400] systemd[1]: modprobe@configfs.service: Succeeded. [ 31.955563] systemd[1]: Finished Load Kernel Module configfs. [ 31.987825] systemd[1]: modprobe@drm.service: Succeeded. [ 32.007683] systemd[1]: Finished Load Kernel Module drm. [ 32.047845] systemd[1]: modprobe@fuse.service: Succeeded. [ 32.065756] systemd[1]: Finished Load Kernel Module fuse. [ 32.087809] systemd[1]: Finished Load Kernel Modules. [ 32.107458] systemd[1]: Finished Remount Root and Kernel File Systems. [ 32.185546] systemd[1]: Mounting FUSE Control File System... [ 32.265537] systemd[1]: Mounting Kernel Configuration File System... [ 32.314566] systemd[1]: Starting pNFS block layout mapping daemon... [ 32.381304] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped. [ 32.405528] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped. [ 32.429723] systemd[1]: Starting Load/Save Random Seed... [ 32.489891] systemd[1]: Starting Apply Kernel Variables... [ 32.570119] systemd[1]: Starting Create System Users... [ 32.633417] systemd[1]: Started Journal Service. [ 33.072950] systemd-journald[235]: Received client request to flush runtime journal. [ 36.270318] adt7475 0-002e: ADT7473 device, revision 0 [ 36.332926] adt7475 0-002e: Optional features: fan4 pwm2 [ 36.361948] orion_wdt: Initial timeout 21 sec [ 36.708305] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 36.935236] sd 3:0:0:0: Attached scsi generic sg1 type 0 [ 37.189232] sd 4:0:0:0: Attached scsi generic sg2 type 0 [ 37.365054] marvell-cesa f1030000.crypto: CESA device successfully registered [ 39.672615] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 39.683336] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 68.067187] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 68.707068] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 73.124886] ata4.00: qc timeout (cmd 0xec) [ 73.129776] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 73.139648] ata4.00: revalidation failed (errno=-5) [ 73.477087] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 73.764876] ata3.00: qc timeout (cmd 0xec) [ 73.769753] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 73.779455] ata3.00: revalidation failed (errno=-5) [ 74.117113] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 83.684876] ata4.00: qc timeout (cmd 0xec) [ 83.689765] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 83.699398] ata4.00: revalidation failed (errno=-5) [ 83.706018] ata4: limiting SATA link speed to 1.5 Gbps [ 84.037108] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 84.049589] ata4.00: configured for UDMA/133 [ 84.324955] ata3.00: qc timeout (cmd 0xec) [ 84.329840] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 84.354141] ata3.00: revalidation failed (errno=-5) [ 84.364927] ata3: limiting SATA link speed to 1.5 Gbps [ 84.717115] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 84.729451] ata3.00: configured for UDMA/133 [ 92.647453] sdc: sdc1 root@debian:~#
Edited 1 time(s). Last edit at 08/24/2022 07:12PM by CodeJACK.
|
Re: Iomega ix4-200d U-boot needed August 24, 2022 07:14PM |
Admin Registered: 13 years ago Posts: 18,543 |
What about these output?
And please post the entire serial log (during uboot booting).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 08/24/2022 07:15PM by bodhi.
sata init sata info sata part
And please post the entire serial log (during uboot booting).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 08/24/2022 07:15PM by bodhi.
|
Re: Iomega ix4-200d U-boot needed August 24, 2022 07:19PM |
Registered: 1 year ago Posts: 52 |
Same as before, nothing:
There is two separate controllers in this thing, correct?
Stock u-boot where the two separate controllers load the disks at different times:
Edited 2 time(s). Last edit at 08/24/2022 07:25PM by CodeJACK.
=> sata init => sata info => sata part no sata partition table available =>
There is two separate controllers in this thing, correct?
Stock u-boot where the two separate controllers load the disks at different times:
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** uboot_ver:v1.1.1 **
** MARVELL BOARD: IX4-110 LE
U-Boot 1.1.4 (Mar 10 2011 - 15:01:57) Marvell version: 3.4.18
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CF600
Soc: 88F6281 A1 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM CS[1] base 0x10000000 size 256MB
DRAM Total size 512MB 16bit width
Found 0x20 i2c device
Toggle power status
Set Power State as Always On
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:32 MB
Found ADT7473, program LED ...(led_volt=90) OK
Found ADT7473, program thermal/Fan ...(pwm_min=0) (pwm_max=130) (therm=67) (temp_min=60) OK
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST6000NM021A-2R7101 Firm: SN03 Ser#: WSE0QQ6A
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1528862.5 MB = 1493.0 GB (3131110576 x 512)
[0 1 0]: Enable DMA mode (6)
Device 1 @ 0 1:
Model: ST6000NM021A-2R7101 Firm: SN03 Ser#: WSE0QPSQ
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1528862.5 MB = 1493.0 GB (3131110576 x 512)
CPU : Marvell Feroceon (Rev 1)
Found initrd at 0x2d4000
Streaming disabled
Write allocate disabled
Module 0 is RGMII
Module 1 is RGMII
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
SCSI: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x7 impl IDE mode
flags: 64bit ncq stag led pmp slum part
scanning bus for devices...
Device 0: (0:0) Vendor: ATA Prod.: ST6000NM021A-2R7 Rev: SN03
Type: Hard Disk
Capacity: 1528862.5 MB = 1493.0 GB (3131110576 x 512)
Device 1: (1:0) Vendor: ATA Prod.: ST6000NM021A-2R7 Rev: SN03
Type: Hard Disk
Capacity: 1528862.5 MB = 1493.0 GB (3131110576 x 512)
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
Marvell>>
Edited 2 time(s). Last edit at 08/24/2022 07:25PM by CodeJACK.
|
Re: Iomega ix4-200d U-boot needed August 24, 2022 07:37PM |
Admin Registered: 13 years ago Posts: 18,543 |
Correct! there are 2 different controllers. I would exepct to see PCI bus handling 2 ports, and internal SATA handling 2 ports.
Ah!
So I recall that you did "scsi reset" in stock u-boot to see the HDDs?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Ah!
SCSI: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x7 impl IDE mode
So I recall that you did "scsi reset" in stock u-boot to see the HDDs?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Iomega ix4-200d U-boot needed August 24, 2022 07:37PM |
Registered: 1 year ago Posts: 52 |
Full boot log with new u-boot:
95 % [......................................................................]
97 % [......................................................................]
99 % [....................................]
[Type Ctrl-\ + c to quit]
U-Boot 2022.10-rc3-tld-0.2 (Aug 24 2022 - 16:52:00 -0700)
Lenovo-ix4-200d
SoC: Kirkwood 88F6281_A1
DRAM: 512 MiB
Core: 12 devices, 9 uclasses, devicetree: separate
NAND: 32 MiB
MMC:
Loading Environment from NAND... OK
In: serial
Out: serial
Err: serial
Net: eth0: ethernet-controller@72000, eth1: ethernet-controller@76000
Hit any key to stop autoboot: 0
=> setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts'
=> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage.orig'
=> setenv load_uinitrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd'
=> setenv load_dtb 'ext2load usb 0:1 0x2c00000 /boot/dts/kirkwood-iomega_ix4_200d.dtb'
=> setenv usb_boot 'usb reset; run set_bootargs; run load_uimage; run load_uinitrd; run load_dtb; bootm 0x800000 0x1100000 0x2c00000'
=> run usb_boot
resetting USB...
Bus ehci@50000: USB EHCI 1.00
scanning bus ehci@50000 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
5729264 bytes read in 246 ms (22.2 MiB/s)
11127733 bytes read in 467 ms (22.7 MiB/s)
9274 bytes read in 32 ms (282.2 KiB/s)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: linux-5.18.6-kirkwood-tld-1.patc
Created: 2022-08-24 23:03:37 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5729200 Bytes = 5.5 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-5.18.6-kirkwood-tld-1
Created: 2022-08-03 18:44:18 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 11127669 Bytes = 10.6 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 02c00000
Booting using the fdt blob at 0x2c00000
Loading Kernel Image
Loading Ramdisk to 1f0b4000, end 1fb50b75 ... OK
Loading Device Tree to 0fffa000, end 0ffff439 ... OK
Starting kernel ...
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 5.18.6-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1.0 PREEMPT Fri Jun 24 15:26:02 PDT 2022
[ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: Iomega ix4-200d
[ 0.000000][ T0] Memory policy: Data cache writeback
[ 0.000000][ T0] Zone ranges:
[ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000001fffffff]
[ 0.000000][ T0] Movable zone start for each node
[ 0.000000][ T0] Early memory node ranges
[ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000001fffffff]
[ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff]
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 130048
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x100000@0x0(u-boot),0x0500000@0x100000(uImage),-(rootfs)
[ 0.000000][ T0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000][ T0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000][ T0] Memory: 488452K/524288K available (11264K kernel code, 1633K rwdata, 4936K rodata, 1024K init, 300K bss, 35836K reserved, 0K cma-reserved)
[ 0.000000][ T0] trace event string verifier disabled
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] Trampoline variant of Tasks RCU enabled.
[ 0.000000][ T0] Tracing variant of Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 0.000002][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 0.000058][ T0] Switching to timer-based delay loop, resolution 5ns
[ 0.001594][ T0] Console: colour dummy device 80x30
[ 0.001668][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000)
[ 0.001712][ T0] pid_max: default: 32768 minimum: 301
[ 0.002389][ T0] LSM: Security Framework initializing
[ 0.002822][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.002872][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.004761][ T0] CPU: Testing write buffer coherency: ok
[ 0.007803][ T1] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.007840][ T1] cblist_init_generic: Setting shift to 0 and lim to 1.
[ 0.008238][ T1] cblist_init_generic: Setting shift to 0 and lim to 1.
[ 0.008722][ T1] Setting up static identity map for 0x100000 - 0x100058
[ 0.009051][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[ 0.009456][ T1] rcu: Hierarchical SRCU implementation.
[ 0.011331][ T1] devtmpfs: initialized
[ 0.017724][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.017781][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.056192][ T1] prandom32: self test passed (less than 6 bits correlated)
[ 0.056239][ T1] prandom: seed boundary self test passed
[ 0.060547][ T1] prandom: 100 self tests passed
[ 0.060577][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.063094][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.063985][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.065264][ T1] audit: initializing netlink subsys (disabled)
[ 0.067327][ T1] thermal_sys: Registered thermal governor 'step_wise'
[ 0.067768][ T16] audit: type=2000 audit(0.060:1): state=initialized audit_enabled=0 res=1
[ 0.067931][ T1] cpuidle: using governor ladder
[ 0.068028][ T1] cpuidle: using governor menu
[ 0.068580][ T1] Feroceon L2: Enabling L2
[ 0.068636][ T1] Feroceon L2: Cache support initialised.
[ 0.079035][ T1] No ATAGs?
[ 0.260295][ T1] raid6: int32x8 gen() 108 MB/s
[ 0.430235][ T1] raid6: int32x4 gen() 95 MB/s
[ 0.600094][ T1] raid6: int32x2 gen() 140 MB/s
[ 0.770391][ T1] raid6: int32x1 gen() 99 MB/s
[ 0.770414][ T1] raid6: using algorithm int32x2 gen() 140 MB/s
[ 0.940072][ T1] raid6: .... xor() 81 MB/s, rmw enabled
[ 0.940093][ T1] raid6: using intx1 recovery algorithm
[ 0.940957][ T1] SCSI subsystem initialized
[ 0.941637][ T1] usbcore: registered new interface driver usbfs
[ 0.941750][ T1] usbcore: registered new interface driver hub
[ 0.941817][ T1] usbcore: registered new device driver usb
[ 0.942102][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 0.942120][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.942158][ T1] PTP clock support registered
[ 0.943920][ T1] vgaarb: loaded
[ 0.944695][ T1] clocksource: Switched to clocksource orion_clocksource
[ 1.081617][ T1] VFS: Disk quotas dquot_6.6.0
[ 1.081740][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.106925][ T1] NET: Registered PF_INET protocol family
[ 1.107281][ T1] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 1.115290][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 1.115545][ T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 1.115587][ T1] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 1.115663][ T1] TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 1.115725][ T1] TCP: Hash tables configured (established 4096 bind 4096)
[ 1.116039][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 1.116144][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 1.116198][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 1.116533][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 1.117589][ T1] RPC: Registered named UNIX socket transport module.
[ 1.117615][ T1] RPC: Registered udp transport module.
[ 1.117629][ T1] RPC: Registered tcp transport module.
[ 1.117641][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.117661][ T1] PCI: CLS 0 bytes, default 32
[ 1.117848][ T1] NetWinder Floating Point Emulator V0.97 (double precision)
[ 1.125126][ T30] Trying to unpack rootfs image as initramfs...
[ 3.084757][ T30] Freeing initrd memory: 10868K
[ 3.845804][ T1] Initialise system trusted keyrings
[ 3.845902][ T1] Key type blacklist registered
[ 3.846310][ T1] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[ 3.846487][ T1] zbud: loaded
[ 3.848805][ T1] NFS: Registering the id_resolver key type
[ 3.848882][ T1] Key type id_resolver registered
[ 3.848899][ T1] Key type id_legacy registered
[ 3.848967][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 3.848994][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 3.849011][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 3.849452][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 3.849986][ T1] fuse: init (API version 7.36)
[ 3.850462][ T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 3.850781][ T1] orangefs_init: module version upstream loaded
[ 3.850803][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled
[ 3.949351][ T1] xor: measuring software checksum speed
[ 3.958318][ T1] arm4regs : 1113 MB/sec
[ 3.973091][ T1] 8regs : 667 MB/sec
[ 3.983518][ T1] 32regs : 947 MB/sec
[ 3.983537][ T1] xor: using function: arm4regs (1113 MB/sec)
[ 3.983559][ T1] async_tx: api initialized (async)
[ 3.983580][ T1] Key type asymmetric registered
[ 3.983595][ T1] Asymmetric key parser 'x509' registered
[ 4.021465][ T1] alg: self-tests for CTR-KDF (hmac(sha256)) passed
[ 4.021724][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[ 4.021893][ T1] io scheduler bfq registered
[ 4.211456][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 4.213854][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges:
[ 4.213956][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000
[ 4.214007][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 4.214044][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 4.214157][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: pcie0.0: legacy INTx interrupts cannot be masked individually, /mbus@f1000000/pcie@82000000/pcie@1,0 does not contain intx interrupt
[ 4.214521][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00
[ 4.214549][ T1] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 4.214576][ T1] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff])
[ 4.214600][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[ 4.214622][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 4.214931][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400
[ 4.216190][ T1] PCI: bus0: Fast back to back transfers disabled
[ 4.216231][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 4.216544][ T1] pci 0000:01:00.0: [11ab:6121] type 00 class 0x01018f
[ 4.216586][ T1] pci 0000:01:00.0: reg 0x10: [io 0x8000-0x8007]
[ 4.216617][ T1] pci 0000:01:00.0: reg 0x14: [io 0x8040-0x8043]
[ 4.216645][ T1] pci 0000:01:00.0: reg 0x18: [io 0x8200-0x8207]
[ 4.216673][ T1] pci 0000:01:00.0: reg 0x1c: [io 0x8800-0x8803]
[ 4.216701][ T1] pci 0000:01:00.0: reg 0x20: [io 0x900000-0x90000f]
[ 4.216730][ T1] pci 0000:01:00.0: reg 0x24: [mem 0x00800000-0x008003ff]
[ 4.216835][ T1] pci 0000:01:00.0: supports D1
[ 4.216855][ T1] pci 0000:01:00.0: PME# supported from D0 D1 D3hot
[ 4.217222][ T1] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 4.218069][ T1] PCI: bus1: Fast back to back transfers disabled
[ 4.218103][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 4.218168][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff]
[ 4.218195][ T1] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff]
[ 4.218226][ T1] pci 0000:01:00.0: BAR 5: assigned [mem 0xe0000000-0xe00003ff]
[ 4.218256][ T1] pci 0000:01:00.0: BAR 4: assigned [io 0x10000-0x1000f]
[ 4.218282][ T1] pci 0000:01:00.0: BAR 0: assigned [io 0x10010-0x10017]
[ 4.218309][ T1] pci 0000:01:00.0: BAR 2: assigned [io 0x10018-0x1001f]
[ 4.218334][ T1] pci 0000:01:00.0: BAR 1: assigned [io 0x10020-0x10023]
[ 4.218360][ T1] pci 0000:01:00.0: BAR 3: assigned [io 0x10024-0x10027]
[ 4.218387][ T1] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 4.218408][ T1] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff]
[ 4.218439][ T1] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff]
[ 4.218602][ T1] pcieport 0000:00:01.0: enabling device (0140 -> 0143)
[ 4.219297][ T1] mv_xor f1060800.xor: Marvell shared XOR driver
[ 4.275826][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 4.279805][ T1] mv_xor f1060900.xor: Marvell shared XOR driver
[ 4.335897][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 4.340183][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 4.341872][ T1] printk: console [ttyS0] disabled
[ 4.341981][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A
[ 5.473861][ T1] printk: console [ttyS0] enabled
[ 5.489236][ T1] loop: module loaded
[ 5.494041][ T1] sata_mv f1080000.sata: slots 32 ports 2
[ 5.504067][ T1] scsi host0: sata_mv
[ 5.508964][ T1] scsi host1: sata_mv
[ 5.513156][ T1] ata1: SATA max UDMA/133 irq 33
[ 5.518039][ T1] ata2: SATA max UDMA/133 irq 33
[ 5.523864][ T1] nand: device found, Manufacturer ID: 0xec, Chip ID: 0x75
[ 5.531051][ T1] nand: Samsung NAND 32MiB 3,3V 8-bit
[ 5.536335][ T1] nand: 32 MiB, SLC, erase size: 16 KiB, page size: 512, OOB size: 16
[ 5.544410][ T1] Scanning device for bad blocks
[ 5.856250][ T48] ata1: SATA link down (SStatus 0 SControl F300)
[ 5.903932][ T1] 3 cmdlinepart partitions found on MTD device orion_nand
[ 5.910961][ T1] Creating 3 MTD partitions on "orion_nand":
[ 5.916885][ T1] 0x000000000000-0x000000100000 : "u-boot"
[ 5.923269][ T1] 0x000000100000-0x000000600000 : "uImage"
[ 5.929758][ T1] 0x000000600000-0x000002000000 : "rootfs"
[ 5.937536][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 5.946152][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 5.989845][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 6.206379][ T50] ata2: SATA link down (SStatus 0 SControl F300)
[ 6.755911][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:b8:13:1d:15
[ 7.525881][ T1] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:d0:b8:13:1d:16
[ 7.535578][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 7.542923][ T1] ehci-pci: EHCI PCI platform driver
[ 7.548189][ T1] ehci-orion: EHCI orion driver
[ 7.553182][ T1] orion-ehci f1050000.ehci: EHCI Host Controller
[ 7.559517][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 7.568171][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000
[ 7.604735][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 7.611796][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.18
[ 7.620840][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.628828][ T1] usb usb1: Product: EHCI Host Controller
[ 7.634432][ T1] usb usb1: Manufacturer: Linux 5.18.6-kirkwood-tld-1 ehci_hcd
[ 7.641897][ T1] usb usb1: SerialNumber: f1050000.ehci
[ 7.648152][ T1] hub 1-0:1.0: USB hub found
[ 7.652673][ T1] hub 1-0:1.0: 1 port detected
[ 7.658317][ T1] usbcore: registered new interface driver usb-storage
[ 7.665596][ T1] mousedev: PS/2 mouse device common for all mice
[ 7.673078][ T1] rtc-mv f1010300.rtc: registered as rtc0
[ 7.678795][ T1] rtc-mv f1010300.rtc: setting system clock to 2022-08-25T00:35:24 UTC (1661387724)
[ 7.688464][ T1] i2c_dev: i2c /dev entries driver
[ 7.695253][ T1] device-mapper: uevent: version 1.0.3
[ 7.700985][ T1] device-mapper: ioctl: 4.46.0-ioctl (2022-02-22) initialised: dm-devel@redhat.com
[ 7.710849][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 7.718186][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 7.725571][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 7.733012][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 7.739865][ T1] device-mapper: raid: Loading target version 1.15.1
[ 7.747433][ T1] hid: raw HID events driver (C) Jiri Kosina
[ 7.753674][ T1] drop_monitor: Initializing network drop monitor service
[ 7.761349][ T1] NET: Registered PF_INET6 protocol family
[ 7.769218][ T1] Segment Routing with IPv6
[ 7.773611][ T1] RPL Segment Routing with IPv6
[ 7.778531][ T1] In-situ OAM (IOAM) with IPv6
[ 7.783302][ T1] NET: Registered PF_PACKET protocol family
[ 7.789455][ T1] Key type dns_resolver registered
[ 7.795379][ T1] registered taskstats version 1
[ 7.800213][ T1] Loading compiled-in X.509 certificates
[ 7.807044][ T1] zswap: loaded using pool lzo/zbud
[ 7.812842][ T1] Key type ._fscrypt registered
[ 7.817668][ T1] Key type .fscrypt registered
[ 7.822312][ T1] Key type fscrypt-provisioning registered
[ 7.833956][ T1] Key type big_key registered
[ 7.870523][ T1] Key type encrypted registered
[ 7.944776][ T45] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 7.975642][ T105] "cryptomgr_test" (105) uses obsolete ecb(arc4) skcipher
[ 8.146427][ T45] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=77.63
[ 8.164715][ T45] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 8.172596][ T45] usb 1-1: Product: USB2.0 Hub
[ 8.195776][ T45] hub 1-1:1.0: USB hub found
[ 8.204728][ T45] hub 1-1:1.0: 4 ports detected
[ 8.534728][ T45] usb 1-1.2: new high-speed USB device number 3 using orion-ehci
[ 8.695674][ T45] usb 1-1.2: New USB device found, idVendor=0781, idProduct=557c, bcdDevice= 1.27
[ 8.714716][ T45] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 8.722768][ T45] usb 1-1.2: Product: Cruzer Orbit
[ 8.744714][ T45] usb 1-1.2: Manufacturer: SanDisk
[ 8.749711][ T45] usb 1-1.2: SerialNumber: 4C530012311126108485
[ 8.765677][ T45] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 8.785275][ T45] scsi host2: usb-storage 1-1.2:1.0
[ 9.849013][ T30] scsi 2:0:0:0: Direct-Access SanDisk Cruzer Orbit 1.27 PQ: 0 ANSI: 6
[ 9.869715][ T8] sd 2:0:0:0: [sda] 62530624 512-byte logical blocks: (32.0 GB/29.8 GiB)
[ 9.887826][ T8] sd 2:0:0:0: [sda] Write Protect is off
[ 9.904727][ T8] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 9.949220][ T8] sda: sda1
[ 9.990577][ T8] sd 2:0:0:0: [sda] Attached SCSI removable disk
[ 12.526880][ T1] Freeing unused kernel image (initmem) memory: 1024K
[ 12.545643][ T1] Checked W+X mappings: passed, no W+X pages found
[ 12.552054][ T1] Run /init as init process
Loading, please wait...
Starting version 247.3-6
[ 13.553654][ T147] ahci 0000:01:00.0: Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this.
[ 13.624822][ T147] ahci 0000:01:00.0: controller can't do NCQ, turning off CAP_NCQ
[ 13.632538][ T147] ahci 0000:01:00.0: controller can't do PMP, turning off CAP_PMP
[ 13.699805][ T147] ahci 0000:01:00.0: masking port_map 0x7 -> 0x3
[ 13.724451][ T152] usbcore: registered new interface driver uas
[ 13.735000][ T147] ahci 0000:01:00.0: SSS flag set, parallel bus scan disabled
[ 13.742408][ T147] ahci 0000:01:00.0: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x3 impl IDE mode
[ 13.820487][ T147] ahci 0000:01:00.0: flags: 64bit stag led slum part
[ 13.889590][ T147] scsi host3: ahci
[ 13.921923][ T147] scsi host4: ahci
[ 13.954464][ T147] scsi host5: ahci
[ 13.971113][ T147] ata3: SATA max UDMA/133 abar m1024@0xe0000000 port 0xe0000100 irq 38
[ 14.026855][ T147] ata4: SATA max UDMA/133 abar m1024@0xe0000000 port 0xe0000180 irq 38
[ 14.071494][ T147] ata5: DUMMY
[ 14.416406][ T154] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 19.444741][ T154] ata3.00: qc timeout (cmd 0xec)
[ 19.449662][ T154] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 19.786402][ T154] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 19.795129][ T154] ata3.00: ATA-11: ST6000NM021A-2R7101, SN03, max UDMA/133
[ 19.802304][ T154] ata3.00: 11721045168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 19.812783][ T154] ata3.00: configured for UDMA/133
[ 19.828357][ T8] scsi 3:0:0:0: Direct-Access ATA ST6000NM021A-2R7 SN03 PQ: 0 ANSI: 5
[ 19.840572][ T161] sd 3:0:0:0: [sdb] 11721045168 512-byte logical blocks: (6.00 TB/5.46 TiB)
[ 19.851313][ T161] sd 3:0:0:0: [sdb] 4096-byte physical blocks
[ 19.857561][ T161] sd 3:0:0:0: [sdb] Write Protect is off
[ 19.863345][ T161] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 19.909140][ T161] sdb: sdb1
[ 19.915418][ T161] sd 3:0:0:0: [sdb] Attached SCSI disk
[ 20.186404][ T156] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 20.195233][ T156] ata4.00: ATA-11: ST6000NM021A-2R7101, SN03, max UDMA/133
[ 20.202413][ T156] ata4.00: 11721045168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 20.212900][ T156] ata4.00: configured for UDMA/133
[ 20.228466][ T30] scsi 4:0:0:0: Direct-Access ATA ST6000NM021A-2R7 SN03 PQ: 0 ANSI: 5
[ 20.240250][ T161] sd 4:0:0:0: [sdc] 11721045168 512-byte logical blocks: (6.00 TB/5.46 TiB)
[ 20.251035][ T161] sd 4:0:0:0: [sdc] 4096-byte physical blocks
[ 20.257225][ T161] sd 4:0:0:0: [sdc] Write Protect is off
[ 20.263031][ T161] sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 20.307930][ T161] sdc: sdc1
[ 20.314228][ T161] sd 4:0:0:0: [sdc] Attached SCSI disk
Begin: Loading essential drivers ... [ 20.879434][ T166] Btrfs loaded, crc32c=crc32c-generic, zoned=no, fsverity=no
done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... Scanning for Btrfs filesystems
done.
Begin: Will now check root file system ... fsck from util-linux 2.36.1
[/sbin/fsck.ext2 (1) -- /dev/sda1] fsck.ext2 -a -C0 /dev/sda1
rootfs: clean, 43172/1954064 files, 678599/7815936 blocks
[ 31.305223][ T119] random: crng init done
done.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
[ 32.239603][ T1] systemd[1]: Inserted module 'autofs4'
[ 32.343191][ T1] systemd[1]: systemd 247.3-7 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified)
[ 32.367436][ T1] systemd[1]: Detected architecture arm.
Welcome to Debian GNU/Linux 11 (bullseye)!
[ 32.416960][ T1] systemd[1]: Set hostname to <debian>.
[ 35.027593][ T1] systemd[1]: Queued start job for default target Graphical Interface.
[ 35.039216][ T1] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling.
[ 35.052519][ T1] systemd[1]: (This warning is only shown for the first unit using IP firewalling.)
[ 35.064016][ T1] systemd[1]: Created slice system-getty.slice.
[ OK ] Created slice system-getty.slice.
[ 35.106338][ T1] systemd[1]: Created slice system-modprobe.slice.
[ OK ] Created slice system-modprobe.slice.
[ 35.146271][ T1] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ OK ] Created slice system-serial\x2dgetty.slice.
[ 35.185945][ T1] systemd[1]: Created slice User and Session Slice.
[ OK ] Created slice User and Session Slice.
[ 35.225512][ T1] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ OK ] Started Dispatch Password …ts to Console Directory Watch.
[ 35.265469][ T1] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ OK ] Started Forward Password R…uests to Wall Directory Watch.
[ 35.306572][ T1] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ OK ] Set up automount Arbitrary…s File System Automount Point.
[ 35.345410][ T1] systemd[1]: Reached target Local Encrypted Volumes.
[ OK ] Reached target Local Encrypted Volumes.
[ 35.385753][ T1] systemd[1]: Reached target Paths.
[ OK ] Reached target Paths.
[ 35.425370][ T1] systemd[1]: Reached target Slices.
[ OK ] Reached target Slices.
[ 35.465234][ T1] systemd[1]: Reached target Swap.
[ OK ] Reached target Swap.
[ 35.495167][ T1] systemd[1]: Reached target System Time Set.
[ OK ] Reached target System Time Set.
[ 35.536378][ T1] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ OK ] Listening on Device-mapper event daemon FIFOs.
[ 35.575876][ T1] systemd[1]: Listening on LVM2 poll daemon socket.
[ OK ] Listening on LVM2 poll daemon socket.
[ 35.616173][ T1] systemd[1]: Listening on RPCbind Server Activation Socket.
[ OK ] Listening on RPCbind Server Activation Socket.
[ 35.657346][ T1] systemd[1]: Listening on Syslog Socket.
[ OK ] Listening on Syslog Socket.
[ 35.696996][ T1] systemd[1]: Listening on fsck to fsckd communication Socket.
[ OK ] Listening on fsck to fsckd communication Socket.
[ 35.735577][ T1] systemd[1]: Listening on initctl Compatibility Named Pipe.
[ OK ] Listening on initctl Compatibility Named Pipe.
[ 35.776434][ T1] systemd[1]: Listening on Journal Audit Socket.
[ OK ] Listening on Journal Audit Socket.
[ 35.815904][ T1] systemd[1]: Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket (/dev/log).
[ 35.856198][ T1] systemd[1]: Listening on Journal Socket.
[ OK ] Listening on Journal Socket.
[ 35.897474][ T1] systemd[1]: Listening on Network Service Netlink Socket.
[ OK ] Listening on Network Service Netlink Socket.
[ 35.936170][ T1] systemd[1]: Listening on udev Control Socket.
[ OK ] Listening on udev Control Socket.
[ 35.975936][ T1] systemd[1]: Listening on udev Kernel Socket.
[ OK ] Listening on udev Kernel Socket.
[ 36.016050][ T1] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
[ 36.030555][ T1] systemd[1]: Mounting POSIX Message Queue File System...
Mounting POSIX Message Queue File System...
[ 36.058635][ T1] systemd[1]: Mounting RPC Pipe File System...
Mounting RPC Pipe File System...
[ 36.110103][ T1] systemd[1]: Mounting Kernel Debug File System...
Mounting Kernel Debug File System...
[ 36.160211][ T1] systemd[1]: Mounting Kernel Trace File System...
Mounting Kernel Trace File System...
[ 36.205529][ T1] systemd[1]: Condition check resulted in Kernel Module supporting RPCSEC_GSS being skipped.
[ 36.216841][ T1] systemd[1]: Finished Availability of block devices.
[ OK ] Finished Availability of block devices.
[ 36.262279][ T1] systemd[1]: Starting Create list of static device nodes for the current kernel...
Starting Create list of st…odes for the current kernel...
[ 36.320017][ T1] systemd[1]: Starting Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling...
Starting Monitoring of LVM…meventd or progress polling...
[ 36.380562][ T1] systemd[1]: Starting Load Kernel Module configfs...
Starting Load Kernel Module configfs...
[ 36.450791][ T1] systemd[1]: Starting Load Kernel Module drm...
Starting Load Kernel Module drm...
[ 36.520447][ T1] systemd[1]: Starting Load Kernel Module fuse...
Starting Load Kernel Module fuse...
[ 36.575355][ T1] systemd[1]: Condition check resulted in OpenVSwitch configuration for cleanup being skipped.
[ 36.597795][ T1] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[ 36.608192][ T1] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[ 36.635780][ T1] systemd[1]: Starting Journal Service...
Starting Journal Service...
[ 36.673524][ T1] systemd[1]: Starting Load Kernel Modules...
Starting Load Kernel Modules...
[ 36.710418][ T1] systemd[1]: Starting Remount Root and Kernel File Systems...
Starting Remount Root and Kernel File Systems...
[ 36.790094][ T1] systemd[1]: Starting Coldplug All udev Devices...
Starting Coldplug All udev Devices...
[ 36.928220][ T1] systemd[1]: Mounted POSIX Message Queue File System.
[ OK ] Mounted POSIX Message Queue File System.
[ 36.963613][ T1] systemd[1]: Mounted RPC Pipe File System.
[ OK ] Mounted RPC Pipe File System.
[ 37.016329][ T1] systemd[1]: Mounted Kernel Debug File System.
[ OK ] Mounted Kernel Debug File System.
[ 37.045895][ T1] systemd[1]: Mounted Kernel Trace File System.
[ OK ] Mounted Kernel Trace File System.
[ 37.058267][ T239] ext2 filesystem being remounted at / supports timestamps until 2038 (0x7fffffff)
[ 37.114991][ T1] systemd[1]: Finished Create list of static device nodes for the current kernel.
[ OK ] Finished Create list of st… nodes for the current kernel.
[ 37.147585][ T1] systemd[1]: Finished Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling.
[ OK ] Finished Monitoring of LVM… dmeventd or progress polling.
[ 37.217312][ T1] systemd[1]: modprobe@configfs.service: Succeeded.
[ 37.245629][ T1] systemd[1]: Finished Load Kernel Module configfs.
[ OK ] Finished Load Kernel Module configfs.
[ 37.277610][ T1] systemd[1]: modprobe@drm.service: Succeeded.
[ 37.305403][ T1] systemd[1]: Finished Load Kernel Module drm.
[ OK ] Finished Load Kernel Module drm.
[ 37.347853][ T1] systemd[1]: modprobe@fuse.service: Succeeded.
[ 37.365812][ T1] systemd[1]: Finished Load Kernel Module fuse.
[ OK ] Finished Load Kernel Module fuse.
[ 37.387549][ T1] systemd[1]: Finished Load Kernel Modules.
[ OK ] Finished Load Kernel Modules.
[ 37.427371][ T1] systemd[1]: Finished Remount Root and Kernel File Systems.
[ OK ] Finished Remount Root and Kernel File Systems.
[ 37.515476][ T1] systemd[1]: Mounting FUSE Control File System...
Mounting FUSE Control File System...
[ 37.585516][ T1] systemd[1]: Mounting Kernel Configuration File System...
Mounting Kernel Configuration File System...
[ 37.637933][ T1] systemd[1]: Starting pNFS block layout mapping daemon...
Starting pNFS block layout mapping daemon...
[ 37.701235][ T1] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[ 37.725445][ T1] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
[ 37.749826][ T1] systemd[1]: Starting Load/Save Random Seed...
Starting Load/Save Random Seed...
[ 37.809901][ T1] systemd[1]: Starting Apply Kernel Variables...
Starting Apply Kernel Variables...
[ 37.890097][ T1] systemd[1]: Starting Create System Users...
Starting Create System Users...
[ 37.973205][ T1] systemd[1]: Started Journal Service.
[ OK ] Started Journal Service.
[ OK ] Mounted FUSE Control File System.
[ OK ] Mounted Kernel Configuration File System.
[ OK ] Started pNFS block layout mapping daemon.
[ OK ] Finished Load/Save Random Seed.
[ OK ] Finished Apply Kernel Variables.
[ OK ] Finished Create System Users.
Starting Flush Journal to Persistent Storage...
Starting Create Static Device Nodes in /dev...
[ OK ] Finished Coldplug All udev Devices.
Starting Helper to synchronize boot up for ifu[ 38.446344][ T235] systemd-journald[235]: Received client request to flush runtime journal.
pdown...
[ OK ] Finished Helper to synchronize boot up for ifupdown.
[ OK ] Finished Create Static Device Nodes in /dev.
[ OK ] Reached target Local File Systems (Pre).
Mounting /tmp...
Starting Rule-based Manage…for Device Events and Files...
[ OK ] Mounted /tmp.
[ OK ] Reached target Local File Systems.
Starting Raise network interfaces...
Starting Preprocess NFS configuration...
Starting Cleanup monit state file...
Starting Cleanup PHP session files...
[ OK ] Finished Preprocess NFS configuration.
[ OK ] Reached target NFS client services.
[ OK ] Finished Cleanup monit state file.
[ OK ] Finished Cleanup PHP session files.
[ OK ] Started Rule-based Manager for Device Events and Files.
Starting Network Service...
[ OK ] Started Network Service.
Starting Wait for Network to be Configured...
[ OK ] Finished Raise network interfaces.
[ 41.575748][ T287] adt7475 0-002e: ADT7473 device, revision 0
[ 41.618916][ T287] adt7475 0-002e: Optional features: fan4 pwm2
[ OK ] Found device /dev/ttyS0.
[ 41.724201][ T284] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 41.812049][ T284] sd 3:0:0:0: Attached scsi generic sg1 type 0
[ 41.828356][ T284] sd 4:0:0:0: Attached scsi generic sg2 type 0
[ 41.841442][ T280] orion_wdt: Initial timeout 21 sec
[ OK ] Finished Flush Journal to Persistent Storage.
Starting Create Volatile Files and Directories...
[ OK ] Finished Create Volatile Files and Directories.
Starting RPC bind portmap service...
Starting Network Name Resolution...
Starting Update UTMP about System Boot/Shutdown...
[ OK ] Started RPC bind portmap service.
[ OK ] Reached target Remote File Systems (Pre).
[ OK ] Reached target Remote File Systems.
[ OK ] Reached target RPC Port Mapper.
[ 42.934868][ T285] marvell-cesa f1030000.crypto: CESA device successfully registered
[ OK ] Finished Update UTMP about System Boot/Shutdown.
[ OK ] Reached target System Initialization.
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
Starting Avahi mDNS/DNS-SD Stack...
Starting LSB: Starts syslogd...
[ OK ] Started Regular background program processing daemon.
[ OK ] Started D-Bus System Message Bus.
Starting Remove Stale Onli…t4 Metadata Check Snapshots...
Starting LSB: Load kernel …d to enable cpufreq scaling...
Starting LSB: service and resource monitoring daemon...
Starting System Logging Service...
Starting User Login Management...
Starting WPA supplicant...
[ OK ] Started LSB: Starts syslogd.
[ OK ] Started System Logging Service.
[ 44.738884][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 44.749610][ T45] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ OK ] Finished Wait for Network to be Configured.
[ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots.
[ OK ] Started LSB: service and resource monitoring daemon.
[ OK ] Started Avahi mDNS/DNS-SD Stack.
[ OK ] Started WPA supplicant.
Starting LSB: Starts klogd...
[ OK ] Started LSB: Starts klogd.
[ OK ] Started User Login Management.
[ OK ] Started Network Name Resolution.
[ OK ] Reached target Network.
[ OK ] Reached target Network is Online.
[ OK ] Reached target Host and Network Name Lookups.
Starting chrony, an NTP client/server...
Starting A high performanc… and a reverse proxy server...
Starting The OpenMediaVaul…t processes the RPC request...
Starting Generate the prelogin message...
Starting The PHP 7.4 FastCGI Process Manager...
Starting /etc/rc.local Compatibility...
Starting OpenBSD Secure Shell server...
Starting Permit User Sessions...
[ OK ] Started LSB: Load kernel m…ded to enable cpufreq scaling.
[ OK ] Finished Permit User Sessions.
Starting LSB: set CPUFreq kernel parameters...
[ OK ] Started /etc/rc.local Compatibility.
[ OK ] Started Getty on tty1.
[ OK ] Started Serial Getty on ttyS0.
[ OK ] Started LSB: set CPUFreq kernel parameters.
[ OK ] Started OpenBSD Secure Shell server.
[FAILED] Failed to start chrony, an NTP client/server.
See 'systemctl status chrony.service' for details.
[ OK ] Started The OpenMediaVault…hat processes the RPC request.
[ OK ] Reached target System Time Synchronized.
[ OK ] Started Trigger anacron every hour.
[ OK ] Started Daily apt download activities.
[ OK ] Started Daily apt upgrade and clean activities.
[ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems.
[ OK ] Started Daily rotation of log files.
[ OK ] Started Daily man-db regeneration.
[ OK ] Started Clean PHP session files every 30 mins.
[ OK ] Reached target Timers.
[ OK ] Started Run anacron jobs.
Starting LSB: start or stop rrdcached...
[ OK ] Started The PHP 7.4 FastCGI Process Manager.
[ OK ] Started A high performance…er and a reverse proxy server.
[ OK ] Started LSB: start or stop rrdcached.
Starting Statistics collection and monitoring daemon...
[ OK ] Started Statistics collection and monitoring daemon.
openmediavault 6.0.37-1 (Shaitan) debian ttyS0
Copyright (C) 2009-2022 by Volker Theile. All rights reserved.
To manage the system visit the openmediavault web control panel:
eth0: 192.168.42.150
By default the web control panel administrator account has the
username 'admin' and password 'openmediavault'.
It is recommended that you change the password for this account
within the web control panel or using the 'omv-firstaid' CLI
command.
For more information regarding this appliance, please visit the
web site: https://www.openmediavault.org
debian login: [ 73.187219][ T156] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 73.194288][ T154] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 73.208747][ T154] ata3.00: configured for UDMA/133
[ 78.244806][ T156] ata4.00: qc timeout (cmd 0xec)
[ 78.249691][ T156] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 78.259359][ T156] ata4.00: revalidation failed (errno=-5)
[ 78.597106][ T156] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 88.804794][ T156] ata4.00: qc timeout (cmd 0xec)
[ 88.809716][ T156] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 88.819332][ T156] ata4.00: revalidation failed (errno=-5)
[ 88.826531][ T156] ata4: limiting SATA link speed to 1.5 Gbps
[ 89.157034][ T156] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 89.169494][ T156] ata4.00: configured for UDMA/133
debian login:
|
Re: Iomega ix4-200d U-boot needed August 24, 2022 07:42PM |
Registered: 1 year ago Posts: 52 |
bodhi Wrote:
-------------------------------------------------------
> Correct! there are 2 different controllers. I
> would exepct to see PCI bus handling 2 ports, and
> internal SATA handling 2 ports.
>
> Ah!
>
> So I recall that you did "scsi reset" in stock
> u-boot to see the HDDs?
Correct but there is no scsi command in the new u-boot
-------------------------------------------------------
> Correct! there are 2 different controllers. I
> would exepct to see PCI bus handling 2 ports, and
> internal SATA handling 2 ports.
>
> Ah!
>
> SCSI: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x7 > impl IDE mode >>
> So I recall that you did "scsi reset" in stock
> u-boot to see the HDDs?
Correct but there is no scsi command in the new u-boot
|
Re: Iomega ix4-200d U-boot needed August 24, 2022 08:10PM |
Admin Registered: 13 years ago Posts: 18,543 |
Do you have all 4 HDDS in the slots? These 2 are internal SATA ports. So I would exepect the "sata init" would find them. If these 2 ports have HDD attached then the u-boot failed to power them up.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST6000NM021A-2R7101 Firm: SN03 Ser#: WSE0QQ6A
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1528862.5 MB = 1493.0 GB (3131110576 x 512)
[0 1 0]: Enable DMA mode (6)
Device 1 @ 0 1:
Model: ST6000NM021A-2R7101 Firm: SN03 Ser#: WSE0QPSQ
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1528862.5 MB = 1493.0 GB (3131110576 x 512)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Iomega ix4-200d U-boot needed August 24, 2022 08:33PM |
Admin Registered: 13 years ago Posts: 18,543 |
Here is the new version. Please kwboot it and
Update:
Re-uploaded the u-boot image.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 08/24/2022 08:45PM by bodhi.
scsi reset scsi info scsi part
Update:
Re-uploaded the u-boot image.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 08/24/2022 08:45PM by bodhi.
|
Re: Iomega ix4-200d U-boot needed August 26, 2022 05:15PM |
Registered: 1 year ago Posts: 52 |
Hey bodhi,
Unfortunately, the new u-boot does not work with the scsi commands. Its tries to run to hangs at:
I power reset and tried running info and part but nothing returned:
Unfortunately, the new u-boot does not work with the scsi commands. Its tries to run to hangs at:
97 % [......................................................................] 99 % [....................................] [Type Ctrl-\ + c to quit] U-Boot 2022.10-rc3-tld-0.3 (Aug 24 2022 - 18:55:05 -0700) Lenovo-ix4-200d SoC: Kirkwood 88F6281_A1 DRAM: 512 MiB Core: 17 devices, 13 uclasses, devicetree: separate NAND: 32 MiB MMC: Loading Environment from NAND... OK In: serial Out: serial Err: serial Net: eth0: ethernet-controller@72000, eth1: ethernet-controller@76000 Hit any key to stop autoboot: 0 => setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts' => setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage.orig' => setenv load_uinitrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd' => setenv load_dtb 'ext2load usb 0:1 0x2c00000 /boot/dts/kirkwood-iomega_ix4_200d.dtb' => setenv usb_boot 'usb reset; run set_bootargs; run load_uimage; run load_uinitrd; run load_dtb; bootm 0x800000 0x1100000 0x2c00000' => scsi reset Reset SCSI scanning bus for devices...
I power reset and tried running info and part but nothing returned:
U-Boot 2022.10-rc3-tld-0.3 (Aug 24 2022 - 18:55:05 -0700) Lenovo-ix4-200d SoC: Kirkwood 88F6281_A1 DRAM: 512 MiB Core: 17 devices, 13 uclasses, devicetree: separate NAND: 32 MiB MMC: Loading Environment from NAND... OK In: serial Out: serial Err: serial Net: eth0: ethernet-controller@72000, eth1: ethernet-controller@76000 Hit any key to stop autoboot: 0 => scsi info => scsi part no scsi partition table available =>
|
Re: Iomega ix4-200d U-boot needed August 26, 2022 05:50PM |
Admin Registered: 13 years ago Posts: 18,543 |
CodeJACK,
kwboot again and interupt u-boot at countdown. And dump some memory like you did in stock u-boot
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
kwboot again and interupt u-boot at countdown. And dump some memory like you did in stock u-boot
md.l 0xF1010000 8 md.l 0xF1010100 1 md.l 0xF1010140 1
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Iomega ix4-200d U-boot needed August 26, 2022 05:56PM |
Registered: 1 year ago Posts: 52 |
|
Re: Iomega ix4-200d U-boot needed August 26, 2022 06:13PM |
Admin Registered: 13 years ago Posts: 18,543 |
mw.l 0xF1010100 0x1000d080 mw.l 0xf1010140 0x0001000c scsi reset
If it hang again, try kwboot previous uploaded version (tld-0.2) and then
mw.l 0xF1010100 0x1000d080 mw.l 0xf1010140 0x0001000c sata init sata info
If still no SATA detected, I'll rebuild another version.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Iomega ix4-200d U-boot needed August 26, 2022 06:23PM |
Registered: 1 year ago Posts: 52 |
Not a hang but controller reset failed:
=> mw.l 0xF1010100 0x1000d080 => mw.l 0xf1010140 0x0001000c => scsi reset Reset SCSI scanning bus for devices... Unsupport SCSI command 0x9d Unsupport SCSI command 0x9d Unsupport SCSI command 0x9d Unsupport SCSI command 0x9d controller reset failed (0x20f1) =>
|
Re: Iomega ix4-200d U-boot needed August 26, 2022 06:32PM |
Admin Registered: 13 years ago Posts: 18,543 |
Ttry kwboot previous uploaded version (tld-0.2) and then
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
mw.l 0xF1010100 0x1000d080 mw.l 0xf1010140 0x0001000c sata init sata info
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Iomega ix4-200d U-boot needed August 26, 2022 06:37PM |
Registered: 1 year ago Posts: 52 |
No joy:
U-Boot 2022.10-rc3-tld-0.2 (Aug 24 2022 - 16:52:00 -0700)
Lenovo-ix4-200d
SoC: Kirkwood 88F6281_A1
DRAM: 512 MiB
Core: 12 devices, 9 uclasses, devicetree: separate
NAND: 32 MiB
MMC:
Loading Environment from NAND... OK
In: serial
Out: serial
Err: serial
Net: eth0: ethernet-controller@72000, eth1: ethernet-controller@76000
Hit any key to stop autoboot: 0
=> mw.l 0xF1010100 0x1000d080
=> mw.l 0xf1010140 0x0001000c
=> sata init
Err: Failed to identify SATA device 0
Err: Failed to identify SATA device 1
=>
=>
=> sata info
Device 0: Model: Firm: Ser#:
Type: Hard Disk
Capacity: not available
Device 1: Model: Firm: Ser#:
Type: Hard Disk
Capacity: not available
=>
|
Re: Iomega ix4-200d U-boot needed August 26, 2022 06:50PM |
Admin Registered: 13 years ago Posts: 18,543 |
The behavior is a bit different
I've been trying to take shortcut but it seems I've missed some code.
Let me explain what we did. We dumped those registers in stock u-boot, and then use those values to force populate the registers in new u-boot. But it seems that did not help. So I will have to go back to do it the old and proven method, but will take a bit of tedious work. If I can, I will build verrsion 0.4 for tomorrow test.
============
I think you have enough to run USB kernel, and HDD rootfs, with stock u-boot. It's not the best set up, but it will allow you to proceed with OMV on HDD. Once the new u-boot is working for SATA, it will be just a couple changes in u-boot envs to boot straight into HDD rootfs.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
=> sata init Err: Failed to identify SATA device 0 Err: Failed to identify SATA device 1
I've been trying to take shortcut but it seems I've missed some code.
Let me explain what we did. We dumped those registers in stock u-boot, and then use those values to force populate the registers in new u-boot. But it seems that did not help. So I will have to go back to do it the old and proven method, but will take a bit of tedious work. If I can, I will build verrsion 0.4 for tomorrow test.
============
I think you have enough to run USB kernel, and HDD rootfs, with stock u-boot. It's not the best set up, but it will allow you to proceed with OMV on HDD. Once the new u-boot is working for SATA, it will be just a couple changes in u-boot envs to boot straight into HDD rootfs.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Iomega ix4-200d U-boot needed August 26, 2022 06:58PM |
Admin Registered: 13 years ago Posts: 18,543 |
CodeJACK ,
bodhi Wrote:
-------------------------------------------------------
> Ttry kwboot previous uploaded version (tld-0.2)
> and then
>
>
Please repeat this test. But with a sleep period.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 08/26/2022 07:00PM by bodhi.
bodhi Wrote:
-------------------------------------------------------
> Ttry kwboot previous uploaded version (tld-0.2)
> and then
>
>
> mw.l 0xF1010100 0x1000d080 > mw.l 0xf1010140 0x0001000c > sata init > sata info >
Please repeat this test. But with a sleep period.
md.l 0xF1010000 8 mw.l 0xF1010100 0x1000d080 mw.l 0xf1010140 0x0001000c sleep 5 sata init sata info
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 08/26/2022 07:00PM by bodhi.
|
Re: Iomega ix4-200d U-boot needed August 26, 2022 07:03PM |
Registered: 1 year ago Posts: 52 |
hmmm, seem to work with the sleep:
Tried with the newer u-boot too:
Edited 1 time(s). Last edit at 08/26/2022 07:09PM by CodeJACK.
=> mw.l 0xF1010100 0x1000d080
=> mw.l 0xf1010140 0x0001000c
=> sleep 5
=> sata init
=> sata info
Device 0: Model: ST6000NM021A-2R7101 Firm: SN03 Ser#: WSE0QQ6A
Type: Hard Disk
Supports 48-bit addressing
Capacity: 5723166.5 MB = 5589.0 GB (11721045168 x 512)
Device 1: Model: ST6000NM021A-2R7101 Firm: SN03 Ser#: WSE0QPSQ
Type: Hard Disk
Supports 48-bit addressing
Capacity: 5723166.5 MB = 5589.0 GB (11721045168 x 512)
=>
Tried with the newer u-boot too:
U-Boot 2022.10-rc3-tld-0.3 (Aug 24 2022 - 18:55:05 -0700) Lenovo-ix4-200d SoC: Kirkwood 88F6281_A1 DRAM: 512 MiB Core: 17 devices, 13 uclasses, devicetree: separate NAND: 32 MiB MMC: Loading Environment from NAND... OK In: serial Out: serial Err: serial Net: eth0: ethernet-controller@72000, eth1: ethernet-controller@76000 Hit any key to stop autoboot: 0 => mw.l 0xF1010100 0x1000d080 => mw.l 0xf1010140 0x0001000c => sleep 5 => sata init Unknown command 'sata' - try 'help' => scsi info => scsi reset Reset SCSI scanning bus for devices... Unsupport SCSI command 0x1c Unsupport SCSI command 0x1c Unsupport SCSI command 0x1c Unsupport SCSI command 0x1c controller reset failed (0x20f1) =>
Edited 1 time(s). Last edit at 08/26/2022 07:09PM by CodeJACK.
|
Re: Iomega ix4-200d U-boot needed August 26, 2022 07:28PM |
Admin Registered: 13 years ago Posts: 18,543 |
CodeJACK,
Cool :) so that's what I thought. Slow disks.
>
OK. So at least 2 HDDs work. That's a victory. Will build version tld-0.4.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Cool :) so that's what I thought. Slow disks.
>
> => mw.l 0xF1010100 0x1000d080 > => mw.l 0xf1010140 0x0001000c > => sleep 5 > => sata init > => sata info > Device 0: Model: ST6000NM021A-2R7101 Firm: SN03 > Ser#: WSE0QQ6A > Type: Hard Disk > Supports 48-bit addressing > Capacity: 5723166.5 MB = 5589.0 GB > (11721045168 x 512) > Device 1: Model: ST6000NM021A-2R7101 Firm: SN03 > Ser#: WSE0QPSQ > Type: Hard Disk > Supports 48-bit addressing > Capacity: 5723166.5 MB = 5589.0 GB > (11721045168 x 512) > => >
OK. So at least 2 HDDs work. That's a victory. Will build version tld-0.4.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Iomega ix4-200d U-boot needed August 26, 2022 07:32PM |
Registered: 1 year ago Posts: 52 |
|
Re: Iomega ix4-200d U-boot needed August 26, 2022 09:58PM |
Admin Registered: 13 years ago Posts: 18,543 |
CodeJACK,
> The disks do seem slow to initialize. The
> controllers themselves are max 3Gbps so each disk
> gets 1.5. This is going to be slow with 4 x 6Tb
> disks but I'm not looking for speed.
Yes. The old Kirkwood boxes controllers are slow. But gaining a few seconds is not that big a deal. Hopefully the new version will already power up the HDDs by the time you do "sata init" to spin it up.
Attached here is version tld-0.4.
This time, kwboot it. And then dump the registers again
If the above does not work then you will have to repeat the pokes to make it work.
==========
And then try SCSI
And please post the log (verbatim from the u-boot banner, don't excerpt).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 08/26/2022 10:18PM by bodhi.
> The disks do seem slow to initialize. The
> controllers themselves are max 3Gbps so each disk
> gets 1.5. This is going to be slow with 4 x 6Tb
> disks but I'm not looking for speed.
Yes. The old Kirkwood boxes controllers are slow. But gaining a few seconds is not that big a deal. Hopefully the new version will already power up the HDDs by the time you do "sata init" to spin it up.
Attached here is version tld-0.4.
This time, kwboot it. And then dump the registers again
md.l 0xF1010000 8 md.l 0xF1010100 1 md.l 0xF1010140 1And
sata init sata info sata part
If the above does not work then you will have to repeat the pokes to make it work.
mw.l 0xF1010100 0x1000d080 mw.l 0xf1010140 0x0001000c sleep 5
==========
And then try SCSI
scsi reset scsi info scsi part
And please post the log (verbatim from the u-boot banner, don't excerpt).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 08/26/2022 10:18PM by bodhi.
|
Re: Iomega ix4-200d U-boot needed August 28, 2022 10:29AM |
Registered: 1 year ago Posts: 52 |
Output below:
99 % [....................................] [Type Ctrl-\ + c to quit] U-Boot 2022.10-rc3-tld-0.4 (Aug 26 2022 - 19:42:06 -0700) Lenovo-ix4-200d SoC: Kirkwood 88F6281_A1 DRAM: 512 MiB Core: 18 devices, 13 uclasses, devicetree: separate NAND: 32 MiB MMC: Loading Environment from NAND... OK In: serial Out: serial Err: serial Net: eth0: ethernet-controller@72000, eth1: ethernet-controller@76000 Hit any key to stop autoboot: 0 => md.l 0xF1010000 8 f1010000: 01111111 00003311 33331140 33003333 .....3..@.3333.3 f1010010: 00000033 00000000 00000000 00000000 3............... => md.l 0xF1010100 1 f1010100: efff3f7f .?.. => md.l 0xF1010140 1 f1010140: fffefff3 .... => sata init Unsupport SCSI command 0x9d Unsupport SCSI command 0x9d Unsupport SCSI command 0x9d Unsupport SCSI command 0x9d controller reset failed (0x2091) Cannot scan SATA device 0 (err=-38) => sata info Unsupport SCSI command 0x9d Unsupport SCSI command 0x9d Unsupport SCSI command 0x9d Unsupport SCSI command 0x9d Unsupport SCSI command 0x9d Unsupport SCSI command 0x9d controller reset failed (0x2091) Cannot scan SATA device 0 (err=-38) => sata part Unsupport SCSI command 0x9d Unsupport SCSI command 0x9d Unsupport SCSI command 0x9d Unsupport SCSI command 0x9d Unsupport SCSI command 0x9d Unsupport SCSI command 0x9d controller reset failed (0x2091) Cannot scan SATA device 0 (err=-38) => mw.l 0xF1010100 0x1000d080 => mw.l 0xf1010140 0x0001000c => sleep 5 => sata init Unsupport SCSI command 0x9d Unsupport SCSI command 0x9d Unsupport SCSI command 0x9d Unsupport SCSI command 0x9d Unsupport SCSI command 0x9d Unsupport SCSI command 0x9d controller reset failed (0x2091) Cannot scan SATA device 0 (err=-38) => scsi reset Reset SCSI scanning bus for devices... Unsupport SCSI command 0x9d Unsupport SCSI command 0x9d Unsupport SCSI command 0x9d Unsupport SCSI command 0x9d controller reset failed (0x2091) => scsi info => scsi part no scsi partition table available =>
|
Re: Iomega ix4-200d U-boot needed August 28, 2022 03:09PM |
Admin Registered: 13 years ago Posts: 18,543 |
Ouch, that's bad. Look like SCSI has some problem co-existing with SATA.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Iomega ix4-200d U-boot needed August 28, 2022 04:33PM |
Admin Registered: 13 years ago Posts: 18,543 |
Attached here is version tld-0.5.
This time, kwboot it. And then dump the registers again
And
If at least 2 SATA drives were initialized, boot into Debian USB rootfs. See if kernel behavior is different or not regarding the 4 HDDs.
===============
The other 2 drives might be still undetected. There is a different controller, which most likely used for PCIe bus to connect these 2 drives.
This is one thing I'm not sure yet.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 08/28/2022 04:43PM by bodhi.
This time, kwboot it. And then dump the registers again
md.l 0xF1010000 8 md.l 0xF1010100 1 md.l 0xF1010140 1
And
sata init sata info sata part
If at least 2 SATA drives were initialized, boot into Debian USB rootfs. See if kernel behavior is different or not regarding the 4 HDDs.
===============
The other 2 drives might be still undetected. There is a different controller, which most likely used for PCIe bus to connect these 2 drives.
Quote
PCIe to SATA RAID Controller;Marvell;88SE6121
This is one thing I'm not sure yet.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 08/28/2022 04:43PM by bodhi.
|
Re: Iomega ix4-200d U-boot needed August 28, 2022 04:42PM |
Registered: 1 year ago Posts: 52 |
Thanks bodhi!
Sadly there is no much to report, see below:
It not not report an issue but also does not report any drives present when all 4 are inserted.
Sadly there is no much to report, see below:
99 % [....................................] [Type Ctrl-\ + c to quit] U-Boot 2022.10-rc3-tld-0.5 (Aug 28 2022 - 14:23:08 -0700) Lenovo-ix4-200d SoC: Kirkwood 88F6281_A1 DRAM: 512 MiB Core: 16 devices, 12 uclasses, devicetree: separate NAND: 32 MiB MMC: Loading Environment from NAND... OK In: serial Out: serial Err: serial pcie0.0: Link up Net: eth0: ethernet-controller@72000, eth1: ethernet-controller@76000 Hit any key to stop autoboot: 0 => md.l 0xF1010000 8 f1010000: 01111111 00003311 33331140 33003333 .....3..@.3333.3 f1010010: 00000033 00000000 00000000 00000000 3............... => md.l 0xF1010100 1 f1010100: 1000c080 .... => md.l 0xF1010140 1 f1010140: 0001000c .... => sata init => sata info => sata part no sata partition table available =>
It not not report an issue but also does not report any drives present when all 4 are inserted.
|
Re: Iomega ix4-200d U-boot needed August 28, 2022 04:49PM |
Admin Registered: 13 years ago Posts: 18,543 |
There was a mistake in my code.
Will upload tld-0.6
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Stock Marvell>> md.l 0xF1010100 1 f1010100: 1000d080 .... Marvell>> md.l 0xF1010140 1 f1010140: 0001000c .... New => md.l 0xF1010100 1 f1010100: 1000c080 .... => md.l 0xF1010140 1 f1010140: 0001000c ....
Will upload tld-0.6
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Iomega ix4-200d U-boot needed August 28, 2022 04:56PM |
Registered: 1 year ago Posts: 52 |
