power off and on - DockStar boots falsely into Pogoplug August 23, 2010 05:03PM |
Registered: 14 years ago Posts: 7 |
Re: power off and on - DockStar boots falsely into Pogoplug August 24, 2010 05:02AM |
Registered: 14 years ago Posts: 7 |
---------------------------------------------------------------------- reboot: ---------------------------------------------------------------------- U-Boot 2010.03-01266-g42f7128-dirty (Aug 22 2010 - 13:33:06) Marvell-Sheevaplug Hit any key to stop autoboot: 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Loading file "/boot/uImage" from usb device 0:1 (usbda1) 1432436 bytes read Loading file "/boot/uImage" from usb device 0:1 (usbda1) 1432436 bytes read Loading file "/boot/uInitrd" from usb device 0:1 (usbda1) 4703837 bytes read ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-2.6.32-5 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1432372 Bytes = 1.4 MB Load Address: 00008000 Entry Point: 0000800 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 4703773 Bytes = 4.5 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ...
---------------------------------------------------------------------- after halt (power off/on) ---------------------------------------------------------------------- U-Boot 2010.03-01266-g42f7128-dirty (Aug 22 2010 - 13:33:06) Marvell-Sheevaplug Hit any key to stop autoboot: 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... Device NOT ready Request Sense returned 00 00 00 1 Storage Device(s) found ** Bad partition 1 ** ** Block device usb 1 not supported ** Block device usb 2 not supported ** Block device usb 3 not supported ** Bad partition 1 ** ** Bad partition 1 ** Wrong Image Format for bootm command ERROR: can't get kernel image! stopping USB.. ### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000 Scanning JFFS2 FS: ......... done. ### JFFS2 load complete: 524288 bytes loaded to 0x800000 ## Starting application at 0x00800200 ...
Re: power off and on - DockStar boots falsely into Pogoplug August 24, 2010 09:01AM |
Admin Registered: 14 years ago Posts: 304 |
Your USB device isn't getting reset, or isn't properly responding to the reset commands. I've seen this before when I reset uBoot at some very strange points, but I've never seen it when just restarting the machine.Quote
scanning bus for storage devices... Device NOT ready
Re: power off and on - DockStar boots falsely into Pogoplug August 24, 2010 10:17AM |
Registered: 14 years ago Posts: 7 |
U-Boot 2010.03-01266-g42f7128-dirty (Aug 22 2010 - 13:33:06) Marvell-Sheevaplug Hit any key to stop autoboot: 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 5 USB Device(s) found scanning bus for storage devices... Device NOT ready Request Sense returned 00 00 00 2 Storage Device(s) found Device NOT ready Request Sense returned 00 00 00 ** Can't read partition table on 0:0 ** ** Bad partition 1 ** ** Bad partition 1 ** ** Block device usb 2 not supported ** Block device usb 3 not supported Device NOT ready Request Sense returned 00 00 00 ** Can't read partition table on 0:0 ** ** Bad partition 1 ** Device NOT ready Request Sense returned 00 00 00 ** Can't read partition table on 0:0 ** ** Bad partition 1 ** ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-2.6.22.18 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1976384 Bytes = 1.9 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... Bad Data CRC ERROR: can't get kernel image! stopping USB.. ### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000 Scanning JFFS2 FS: ......... done. ### JFFS2 load complete: 524288 bytes loaded to 0x800000 ## Starting application at 0x00800200 ...
Re: power off and on - DockStar boots falsely into Pogoplug August 24, 2010 02:34PM |
Registered: 14 years ago Posts: 7 |
U-Boot 2010.03-01266-g42f7128-dirty (Aug 22 2010 - 13:33:06) Marvell-Sheevaplug Hit any key to stop autoboot: 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 5 USB Device(s) found scanning bus for storage devices... Device NOT ready Request Sense returned 00 00 00 error in inquiry 2 Storage Device(s) found Device NOT ready Request Sense returned 00 00 00 ** Can't read partition table on 0:0 ** ** Bad partition 1 ** ** Bad partition 1 ** ** Block device usb 2 not supported ** Block device usb 3 not supported Device NOT ready Request Sense returned 00 00 00 ** Can't read partition table on 0:0 ** ** Bad partition 1 ** Device NOT ready Request Sense returned 00 00 00 ** Can't read partition table on 0:0 ** ** Bad partition 1 ** ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-2.6.22.18 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1976384 Bytes = 1.9 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... Bad Data CRC ERROR: can't get kernel image! stopping USB.. ### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000 Scanning JFFS2 FS: ......... done. ### JFFS2 load complete: 524288 bytes loaded to 0x800000 ## Starting application at 0x00800200 ...
Re: power off and on - DockStar boots falsely into Pogoplug August 24, 2010 04:03PM |
Registered: 14 years ago Posts: 7 |
Vijay
Re: power off and on - DockStar boots falsely into Pogoplug September 02, 2010 08:31AM |
Vijay
Re: power off and on - DockStar boots falsely into Pogoplug September 02, 2010 08:41AM |
Re: power off and on - DockStar boots falsely into Pogoplug September 07, 2010 05:51PM |
Registered: 13 years ago Posts: 24 |
nema@phobos:~$ ./netconsole 192.168.2.15 6666 NOTE: the interrupt signal (normally ^C) has been remapped to ^T U-Boot 2010.06-00695-gbd23130-dirty (Aug 30 2010 - 23:04:56) Marvell-Dockstar/Pogoplug by Jeff Doozan Hit any key to stop autoboot: 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... error in inquiry 0 Storage Device(s) found ** Block device usb 0 not supported ** Block device usb 0 not supported Wrong Image Format for bootm command ERROR: can't get kernel image! stopping USB.. ### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000 Scanning JFFS2 FS: ......... done. ### JFFS2 load complete: 524288 bytes loaded to 0x800000 ## Starting application at 0x00800200 ...
U-Boot 2010.06-00695-gbd23130-dirty (Aug 30 2010 - 23:04:56) Marvell-Dockstar/Pogoplug by Jeff Doozan Hit any key to stop autoboot: 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Loading file "/boot/uImage" from usb device 0:1 (usbda1) 1430120 bytes read Loading file "/boot/uInitrd" from usb device 0:1 (usbda1) 4703913 bytes read ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-2.6.32-5 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1430056 Bytes = 1.4 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 4703849 Bytes = 4.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ...
Re: power off and on - DockStar boots falsely into Pogoplug September 18, 2010 12:00PM |
Registered: 13 years ago Posts: 18 |
JusRelax
Re: power off and on - DockStar boots falsely into Pogoplug September 19, 2010 04:57AM |
JusRelax
Re: power off and on - DockStar boots falsely into Pogoplug September 19, 2010 04:59AM |
JusRelax
Re: power off and on - DockStar boots falsely into Pogoplug September 19, 2010 10:59AM |
Re: power off and on - DockStar boots falsely into Pogoplug September 19, 2010 01:29PM |
Registered: 13 years ago Posts: 18 |
JusRelax
Re: power off and on - DockStar boots falsely into Pogoplug September 19, 2010 03:46PM |
Re: power off and on - DockStar boots falsely into Pogoplug September 19, 2010 06:32PM |
Registered: 13 years ago Posts: 24 |
Re: power off and on - DockStar boots falsely into Pogoplug September 19, 2010 09:59PM |
Registered: 13 years ago Posts: 18 |
Re: power off and on - DockStar boots falsely into Pogoplug September 21, 2010 10:50AM |
Registered: 14 years ago Posts: 54 |
Re: power off and on - DockStar boots falsely into Pogoplug October 15, 2010 01:04PM |
Registered: 13 years ago Posts: 24 |
setenv usb_init usb startbecomes:
setenv usb_init 'if usb start; then version; else usb stop; usb start;fi;'
setenv usb_load_uimage 'mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage'
setenv usb_load_uimage 'mw 0x800000 0 1; run usb_ext2load_uimage' setenv usb_ext2load_uimage 'if ext2load usb $usb_device 0x800000 /boot/uImage; then version; else usb stop; run usb_init; ext2load usb $usb_device 0x800000 /boot/uImage;fi;'
setenv usb_ext2load_uimage ext2load usb $usb_device 0x800000 /boot/uImage setenv usb_load_uimage 'mw 0x800000 0 1; if run usb_ext2load_uimage; then version; else usb stop; run usb_init; run usb_ext2load_uimage;fi;'
Fred Snertz
Re: power off and on - DockStar boots falsely into Pogoplug December 05, 2010 09:12AM |
$ /usr/sbin/fw_printenv | grep ^bootcmd bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset $ /usr/sbin/fw_setenv bootcmd "usb start; usb stop; usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset" $ /usr/sbin/fw_printenv | grep ^bootcmd bootcmd=usb start; usb stop; usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset
Chris Z
Re: power off and on - DockStar boots falsely into Pogoplug December 29, 2010 09:15AM |
raccoon8888
Re: power off and on - DockStar boots falsely into Pogoplug June 28, 2011 10:32AM |
Re: power off and on - DockStar boots falsely into Pogoplug September 13, 2011 11:49AM |
Registered: 12 years ago Posts: 9 |
setenv usb_init "usb reset; usb start" saveenv
Lallo
Re: power off and on - DockStar boots falsely into Pogoplug March 30, 2014 03:54PM |
-sh-3.2# fw_printenv ethact=egiga0 bootdelay=3 baudrate=115200 mainlineLinux=yes console=ttyS0,115200 led_init=green blinking led_exit=green off led_error=orange blinking mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) mtdids=nand0=orion_nand partition=nand0,2 stdin=serial stdout=serial stderr=serial rescue_installed=0 rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi ubifs_mtd=3 ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done usb_scan_list=1 2 3 4 usb_scan_1=usb=0:1 dev=sda1 usb_scan_2=usb=1:1 dev=sdb1 usb_scan_3=usb=2:1 dev=sdc1 usb_scan_4=usb=3:1 dev=sdd1 usb_init=run usb_scan usb_device=0:1 usb_root=/dev/sda1 usb_rootfstype=ext2 usb_rootdelay=10 usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset ethaddr=00:50:43:00:02:02 arcNumber=2097 ipaddr=192.168.1.100 if_netconsole=ping $serverip start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; preboot=run if_netconsole start_netconsole usb_set_bootargs=setenv bootargs console=$console root=UUID=$usb_root_uuid rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params usb_root_uuid=afe306a5-db03-4b36-98d0-d7531c1f53a7
-sh-3.2# reboot The system is going down NOW! Sending SIGTERM to all processes Requesting system reboot [ 454.350000] md: stopping all md devices. [ 455.350000] Restarting system. [ 455.350000] Reseting !! U-Boot 2011.12 (Feb 12 2012 - 21:33:07) Seagate FreeAgent DockStar SoC: Kirkwood 88F6281_A0 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 88E1116 Initialized on egiga0 Hit any key to stop autoboot: 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Loading file "/rescueme" from usb device 0:1 (usbda1) ** File not found /rescueme reading /rescueme.txt ** Unable to read "/rescueme.txt" from usb 0:1 ** Creating 1 MTD partitions on "nand0": 0x000002500000-0x000010000000 : "mtd=3" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=3" UBI: MTD device size: 219 MiB UBI: number of good PEBs: 1752 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 0 UBI: available PEBs: 1731 UBI: total number of reserved PEBs: 21 UBI: number of PEBs reserved for bad PEB handling: 17 UBI: max/mean erase counter: 1/1 UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19 Error reading superblock on volume 'ubi:rootfs'! Loading file "/boot/uImage" from usb device 0:1 (usbda1) ** File not found /boot/uImage ** Block device usb 1 not supported ** Block device usb 2 not supported ** Block device usb 3 not supported Loading file "/boot/uImage" from usb device 0:1 (usbda1) ** File not found /boot/uImage Loading file "/boot/uInitrd" from usb device 0:1 (usbda1) ** File not found /boot/uInitrd Wrong Image Format for bootm command ERROR: can't get kernel image! stopping USB.. ### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000 Scanning JFFS2 FS: ......... done. ### JFFS2 load complete: 524288 bytes loaded to 0x800000 ## Starting application at 0x00800200 ... U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:256 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: REDSTONE:0.1 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x100000, size 0x300000 Reading data from 0x3ff800 -- 100% complete. 3145728 bytes read: OK ## Booting image at 00800000 ... Image Name: Linux-2.6.22.18 Created: 2009-10-14 20:23:19 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1978544 Bytes = 1.9 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux............................................................................................................................ done, booting the kernel. [ 0.000000] Linux version 2.6.22.18 (bdietrich@brad-ux) (gcc version 4.2.1) #63 Wed Oct 14 13:23:16 PDT 2009 [ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177 [ 0.000000] Machine: Feroceon-KW [ 0.000000] Using UBoot passing parameters structure [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] CPU0: D VIVT write-back cache [ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] Built 1 zonelists. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro [ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes) [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 128MB 0MB 0MB 0MB = 128MB total [ 0.000000] Memory: 125824KB available (3592K code, 253K data, 124K init) [ 0.240000] Mount-cache hash table entries: 512 [ 0.240000] CPU: Testing write buffer coherency: ok [ 0.240000] NET: Registered protocol family 16 [ 0.240000] [ 0.240000] CPU Interface [ 0.240000] ------------- [ 0.240000] SDRAM_CS0 ....base 00000000, size 128MB [ 0.240000] SDRAM_CS1 ....disable [ 0.240000] SDRAM_CS2 ....disable [ 0.240000] SDRAM_CS3 ....disable [ 0.240000] PEX0_MEM ....base e8000000, size 128MB [ 0.240000] PEX0_IO ....base f2000000, size 1MB [ 0.240000] INTER_REGS ....base f1000000, size 1MB [ 0.240000] NFLASH_CS ....base fa000000, size 2MB [ 0.240000] SPI_CS ....base f4000000, size 16MB [ 0.240000] BOOT_ROM_CS ....no such [ 0.240000] DEV_BOOTCS ....no such [ 0.240000] CRYPT_ENG ....base f0000000, size 2MB [ 0.240000] [ 0.240000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21_with_rx_desc_tuned)-- SHEEVA PLUG Soc: 88F6281 A0 LE [ 0.240000] [ 0.240000] Detected Tclk 200000000 and SysClk 400000000 [ 0.240000] MV Buttons Device Load [ 0.240000] Marvell USB EHCI Host controller #0: c0539600 [ 0.740000] PEX0 interface detected no Link. [ 0.740000] PCI: bus0: Fast back to back transfers enabled [ 0.740000] SCSI subsystem initialized [ 0.740000] usbcore: registered new interface driver usbfs [ 0.740000] usbcore: registered new interface driver hub [ 0.740000] usbcore: registered new device driver usb [ 0.740000] NET: Registered protocol family 2 [ 0.750000] Time: kw_clocksource clocksource has been installed. [ 0.840000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.840000] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.840000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.840000] TCP: Hash tables configured (established 4096 bind 4096) [ 0.840000] TCP reno registered [ 0.870000] RTC has been updated!!! [ 0.870000] RTC registered [ 0.870000] Use the XOR engines (acceleration) for enhancing the following functions: [ 0.870000] o RAID 5 Xor calculation [ 0.870000] o kernel memcpy [ 0.870000] o kenrel memzero [ 0.870000] Number of XOR engines to use: 4 [ 0.870000] cesadev_init(c00116f0) [ 0.870000] mvCesaInit: sessions=640, queue=64, pSram=f0000000 [ 0.870000] MV Buttons Driver Load [ 0.870000] squashfs: version 3.3 (2007/10/31) Phillip Lougher [ 0.870000] squashfs: LZMA suppport for slax.org by jro [ 0.870000] JFFS2 version 2.2. (NAND) é 2001-2006 Red Hat, Inc. [ 0.870000] io scheduler noop registered [ 0.870000] io scheduler anticipatory registered (default) [ 0.890000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [ 0.890000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A [ 0.900000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize [ 0.910000] Loading Marvell Ethernet Driver: [ 0.910000] o Cached descriptors in DRAM [ 0.910000] o DRAM SW cache-coherency [ 0.920000] o Single RX Queue support - ETH_DEF_RXQ=0 [ 0.920000] o Single TX Queue support - ETH_DEF_TXQ=0 [ 0.930000] o TCP segmentation offload enabled [ 0.930000] o Receive checksum offload enabled [ 0.940000] o Transmit checksum offload enabled [ 0.940000] o Network Fast Processing (Routing) supported [ 0.950000] o Driver ERROR statistics enabled [ 0.950000] o Driver INFO statistics enabled [ 0.960000] o Proc tool API enabled [ 0.960000] o Rx descripors: q0=128 [ 0.960000] o Tx descripors: q0=532 [ 0.970000] o Loading network interface(s): [ 0.970000] o eth0, ifindex = 1, GbE port = 0 [ 0.980000] o eth1, ifindex = 2, GbE port = 1 [ 0.990000] [ 0.990000] mvFpRuleDb (c7ed4000): 1024 entries, 4096 bytes [ 0.990000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI [ 1.000000] Copyright (c) 1999-2006 Intel Corporation. [ 1.010000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI [ 1.010000] e100: Copyright(c) 1999-2006 Intel Corporation [ 1.020000] [ 1.020000] Warning Sata is Powered Off [ 1.020000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ [ 1.030000] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit) [ 1.040000] Scanning device for bad blocks [ 1.140000] Using static partition definition [ 1.150000] Creating 4 MTD partitions on "nand_mtd": [ 1.150000] 0x00000000-0x00100000 : "u-boot" [ 1.160000] 0x00100000-0x00500000 : "uImage" [ 1.160000] 0x00500000-0x02500000 : "root" [ 1.170000] 0x02500000-0x10000000 : "data" [ 1.170000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI [ 1.180000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 [ 1.210000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 [ 1.230000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 1.230000] usb usb1: configuration #1 chosen from 1 choice [ 1.240000] hub 1-0:1.0: USB hub found [ 1.240000] hub 1-0:1.0: 1 port detected [ 1.360000] USB Universal Host Controller Interface driver v3.0 [ 1.640000] usb 1-1: new high speed USB device using ehci_marvell and address 2 [ 1.790000] usb 1-1: configuration #1 chosen from 1 choice [ 1.790000] hub 1-1:1.0: USB hub found [ 1.800000] hub 1-1:1.0: 4 ports detected [ 2.150000] usb 1-1.2: new high speed USB device using ehci_marvell and address 3 [ 2.250000] usb 1-1.2: configuration #1 chosen from 1 choice [ 2.250000] usbcore: registered new interface driver usblp [ 2.260000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver [ 2.270000] Initializing USB Mass Storage driver... [ 2.270000] scsi0 : SCSI emulation for USB Mass Storage devices [ 2.280000] usbcore: registered new interface driver usb-storage [ 2.280000] USB Mass Storage support registered. [ 2.290000] mice: PS/2 mouse device common for all mice [ 2.290000] i2c /dev entries driver [ 2.300000] Linux telephony interface: v1.00 [ 2.300000] md: linear personality registered for level -1 [ 2.310000] md: raid0 personality registered for level 0 [ 2.310000] md: raid1 personality registered for level 1 [ 2.490000] raid6: int32x1 97 MB/s [ 2.660000] raid6: int32x2 114 MB/s [ 2.830000] raid6: int32x4 122 MB/s [ 3.000000] raid6: int32x8 110 MB/s [ 3.000000] raid6: using algorithm int32x4 (122 MB/s) [ 3.000000] md: raid6 personality registered for level 6 [ 3.010000] md: raid5 personality registered for level 5 [ 3.010000] md: raid4 personality registered for level 4 [ 3.020000] raid5: measuring checksumming speed [ 3.070000] arm4regs : 1084.000 MB/sec [ 3.120000] 8regs : 754.800 MB/sec [ 3.170000] 32regs : 899.600 MB/sec [ 3.170000] raid5: using function: arm4regs (1084.000 MB/sec) [ 3.180000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com [ 3.180000] dm_crypt using the OCF package. [ 3.190000] sdhci: Secure Digital Host Controller Interface driver [ 3.190000] sdhci: Copyright(c) Pierre Ossman [ 3.200000] usbcore: registered new interface driver usbhid [ 3.200000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 3.210000] TCP cubic registered [ 3.210000] NET: Registered protocol family 1 [ 3.220000] NET: Registered protocol family 17 [ 3.220000] md: Autodetecting RAID arrays. [ 3.230000] md: autorun ... [ 3.230000] md: ... autorun DONE. [ 6.450000] Empty flash at 0x009ac208 ends at 0x009ac800 [ 7.580000] VFS: Mounted root (jffs2 filesystem) readonly. [ 7.580000] Freeing init memory: 124K [ 7.600000] scsi 0:0:0:0: Direct-Access USB Reader 0001 PQ: 0 ANSI: 0 CCS [ 8.390000] sd 0:0:0:0: [sda] 15564800 512-byte hardware sectors (7969 MB) [ 8.410000] sd 0:0:0:0: [sda] Write Protect is off [ 8.410000] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 8.460000] sd 0:0:0:0: [sda] 15564800 512-byte hardware sectors (7969 MB) [ 8.480000] sd 0:0:0:0: [sda] Write Protect is off [ 8.480000] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 8.490000] sda: sda1 sda2 [ 8.500000] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 8.500000] sd 0:0:0:0: Attached scsi generic sg0 type 0 init started: BusyBox v1.7.0 (2008-02-26 19:25:17 IST) starting pid 284, tty '': '/etc/init.d/rcS' [ 9.790000] eth0: started udhcpc (v1.7.0) started HWADDR 00 0x50 0x43 0x00 0x02 0x02 PIP0 2 PIP1 2 Sending discover... Sending discover... Sending discover... HWADDR 00 0x50 0x43 0x00 0x02 0x02 PIP0 2 PIP1 2 Unexpected Argument: leasefail interface=eth0 PATH=/sbin:/usr/sbin:/bin:/usr/bin PWD=/ SHLVL=1 HOME=/ _=/bin/printenv No lease, forking to background starting pid 329, tty '': '/bin/sh' -sh-3.2# mount /dev/sda1 /mnt [ 25.090000] EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended -sh-3.2# cat /mnt/etc/debian_version 6.0.9 -sh-3.2#