Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 27, 2016 12:53AM |
Registered: 7 years ago Posts: 310 |
debian:~# echo "default-on" > /sys/class/leds/sheevaplug\:blue\:health/trigger debian:~# echo "none" > /sys/class/leds/sheevaplug\:red\:misc/trigger
feas@debian:~$ sudo cp uboot.2016.05-tld-1.pogo_e02.bodhi.tar /tmp [sudo] password for feas: feas@debian:~$ cd /tmp feas@debian:/tmp$ ls uboot.2016.05-tld-1.pogo_e02.bodhi.tar feas@debian:/tmp$ tar xvf uboot.2016.05-tld-1.pogo_e02.bodhi.tar uboot.2016.05-tld-1.pogo_e02.mtd0.kwb feas@debian:/tmp$ ls uboot.2016.05-tld-1.pogo_e02.bodhi.tar uboot.2016.05-tld-1.pogo_e02.mtd0.kwb feas@debian:/tmp$ su Password: root@debian:/tmp# ls uboot.2016.05-tld-1.pogo_e02.bodhi.tar uboot.2016.05-tld-1.pogo_e02.mtd0.kwb root@debian:/tmp# flash_erase /dev/mtd0 0 4 Erasing 128 Kibyte @ 60000 -- 100 % complete root@debian:/tmp# nandwrite /dev/mtd0 uboot.2016.05-tld-1.pogo_e02.mtd0.kwb Writing data to block 0 at offset 0x0 Writing data to block 1 at offset 0x20000 Writing data to block 2 at offset 0x40000 Writing data to block 3 at offset 0x60000 root@debian:/tmp# cat /etc/fw_env.config # Configuration file for fw_(printenv/saveenv) utility. # Up to two entries are valid, in this case the redundant # environment sector is assumed present. # Notice, that the "Number of sectors" is ignored on NOR. # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd0 0xc0000 0x20000 0x20000 root@debian:/tmp# wget http://www.dropbox.com/s/4smmw2wr4ugayz9/uboot.2016.05-tld-1.environment.bodhi.tar --2016-07-27 00:04:40-- http://www.dropbox.com/s/4smmw2wr4ugayz9/uboot.2016.05-tld-1.environment.bodhi.tar Resolving www.dropbox.com (www.dropbox.com)... 162.125.4.1 Connecting to www.dropbox.com (www.dropbox.com)|162.125.4.1|:80... connected. HTTP request sent, awaiting response... 301 Moved Permanently Location: https://www.dropbox.com/s/4smmw2wr4ugayz9/uboot.2016.05-tld-1.environment.bodhi.tar [following] --2016-07-27 00:04:40-- https://www.dropbox.com/s/4smmw2wr4ugayz9/uboot.2016.05-tld-1.environment.bodhi.tar Connecting to www.dropbox.com (www.dropbox.com)|162.125.4.1|:443... connected. HTTP request sent, awaiting response... 302 Found Location: https://dl.dropboxusercontent.com/content_link/sMx557hgs9i4iWyXeOpwjjfenZ5IxCxPMfFrJuO5il7zd525B5xNg7w5jmQv05EX/file [following] --2016-07-27 00:04:41-- https://dl.dropboxusercontent.com/content_link/sMx557hgs9i4iWyXeOpwjjfenZ5IxCxPMfFrJuO5il7zd525B5xNg7w5jmQv05EX/file Resolving dl.dropboxusercontent.com (dl.dropboxusercontent.com)... 45.58.74.37 Connecting to dl.dropboxusercontent.com (dl.dropboxusercontent.com)|45.58.74.37|:443... connected. HTTP request sent, awaiting response... 200 OK Length: 204800 (200K) [application/x-tar] Saving to: ‘uboot.2016.05-tld-1.environment.bodhi.tar’ uboot.2016.05-tld-1.en 100%[===========================>] 200.00K --.-KB/s in 0.1s 2016-07-27 00:04:41 (2.05 MB/s) - ‘uboot.2016.05-tld-1.environment.bodhi.tar’ saved [204800/204800] root@debian:/tmp# ls uboot.2016.05-tld-1.environment.bodhi.tar uboot.2016.05-tld-1.pogo_e02.mtd0.kwb uboot.2016.05-tld-1.pogo_e02.bodhi.tar root@debian:/tmp# tar xvf uboot.2016.05-tld-1.environment.bodhi.tar uboot.2016.05-tld-1.environment.img uboot.2016.05-tld-1.environment.64K.img uboot.2016.05-tld-1.environment root@debian:/tmp# fw_printenv > current_envs.txt root@debian:/tmp# /usr/sbin/flash_erase /dev/mtd0 0xc0000 1 Erasing 128 Kibyte @ c0000 -- 100 % complete root@debian:/tmp# /usr/sbin/nandwrite -s 786432 /dev/mtd0 uboot.2016.05-tld-1.environment.img Writing data to block 6 at offset 0xc0000 root@debian:/tmp# fw_setenv arcNumber 3542 root@debian:/tmp# fw_setenv machid dd6 root@debian:/tmp# cat current_envs.txt ethact=egiga0 bootdelay=3 baudrate=115200 mainlineLinux=yes console=ttyS0,115200 led_init=green blinking led_exit=green off led_error=orange blinking mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) mtdids=nand0=orion_nand partition=nand0,2 stdin=serial stdout=serial stderr=serial rescue_installed=0 rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi ubifs_mtd=3 ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done usb_scan_list=1 2 3 4 usb_scan_1=usb=0:1 dev=sda1 usb_scan_2=usb=1:1 dev=sdb1 usb_scan_3=usb=2:1 dev=sdc1 usb_scan_4=usb=3:1 dev=sdd1 usb_init=run usb_scan usb_device=0:1 usb_root=/dev/sda1 usb_rootfstype=ext2 usb_rootdelay=10 usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset serverip=192.168.86.110 ipaddr=192.168.86.109 if_netconsole=ping $serverip start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; preboot=run if_netconsole start_netconsole arcNumber=3542 ethaddr=00:25:31:04:7B:64 root@debian:/tmp# fw_setenv mtdparts 'mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)' root@debian:/tmp# fw_setenv ethaddr '00:25:31:04:7B:64' root@debian:/tmp# fw_printenv bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 ethact=egiga0 if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking dtb_file=/boot/dts/kirkwood-pogo_e02.dtb load_dtb_addr=0x1c00000 load_initrd_addr=0x1100000 load_uimage_addr=0x800000 load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage mainlineLinux=yes mtdids=nand0=orion_nand partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi usb_ready_retry=15 arcNumber=3542 machid=dd6 mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) ethaddr=00:25:31:04:7B:64 root@debian:/tmp# cat /boot/uEnv.txt cat: /boot/uEnv.txt: No such file or directory root@debian:/tmp# fw_printenv > /boot/uEnv.txt root@debian:/tmp# fw_setenv preboot_nc 'setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi' root@debian:/tmp# fw_setenv preboot 'run preboot_nc' root@debian:/tmp# fw_setenv ipaddr '192.168.86.109' root@debian:/tmp# fw_setenv serverip '192.168.86.110' root@debian:/tmp# reboot Connection to 192.168.86.109 closed by remote host. Connection to 192.168.86.109 closed.
feas@debian-laptop:~$ sudo picocom -b 115200 /dev/ttyUSB0 [sudo] password for feas: picocom v1.7 port is : /dev/ttyUSB0 flowcontrol : none baudrate is : 115200 parity is : none databits are : 8 escape is : C-a local echo is : no noinit is : no noreset is : no nolock is : no send_cmd is : sz -vv receive_cmd is : rz -vv imap is : omap is : emap is : crcrlf,delbs, Terminal ready U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:23:43 -0700) Pogo E02 SoC: Kirkwood 88F6281_A0 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Unknown command 'ide' - try 'help' Unknown command 'mmc' - try 'help' Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 12582912 b57a22f8-01 83 Boot 2 12584960 4194304 b57a22f8-02 82 loading envs from usb 0 ... 2788 bytes read in 153 ms (17.6 KiB/s) Unknown command 'ide' - try 'help' Unknown command 'mmc' - try 'help' importing envs ... himport_r: ethaddr=00:25:31:04:7B:64" into hash table running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 136 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 2082764 bytes read in 264 ms (7.5 MiB/s) loading uInitrd ... 10550768 bytes read in 814 ms (12.4 MiB/s) loading DTB /boot/dts/kirkwood-pogo_e02.dtb ... ** File not found /boot/dts/kirkwood-pogo_e02.dtb ** ## Booting kernel from Legacy Image at 00800000 ... Image Name: kernel 3.16.0-4-kirkwood Created: 2016-07-26 8:56:48 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2082700 Bytes = 2 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: ramdisk 3.16.0-4-kirkwood Created: 2016-07-26 8:56:58 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 10550704 Bytes = 10.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK Using machid 0xdd6 from environment Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.16.0-4-kirkwood (debian-kernel@lists.debian.org) (gcc version 4.8.4 (Debian 4.8.4-1) ) #1 Debian 3.16.36-1 (2016-07-04) [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine model: Globalscale Technologies SheevaPlug [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 243184K/262144K available (3907K kernel code, 360K rwdata, 1440K rodata, 277K init, 288K bss, 18960K reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc05410c4 (5349 kB) [ 0.000000] .init : 0xc0542000 - 0xc058774c ( 278 kB) [ 0.000000] .data : 0xc0588000 - 0xc05e2168 ( 361 kB) [ 0.000000] .bss : 0xc05e2168 - 0xc062a54c ( 289 kB) [ 0.000000] NR_IRQS:114 [ 0.000015] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474836475ns [ 0.000319] Console: colour dummy device 80x30 [ 0.000344] Calibrating delay loop... 1185.79 BogoMIPS (lpj=2371584) [ 0.024040] pid_max: default: 32768 minimum: 301 [ 0.024171] Security Framework initialized [ 0.024222] Yama: disabled by default; enable with sysctl kernel.yama.* [ 0.024301] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.024319] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.025094] Initializing cgroup subsys memory [ 0.025136] Initializing cgroup subsys devices [ 0.025187] Initializing cgroup subsys freezer [ 0.025212] Initializing cgroup subsys net_cls [ 0.025256] Initializing cgroup subsys blkio [ 0.025292] Initializing cgroup subsys perf_event [ 0.025314] Initializing cgroup subsys net_prio [ 0.025400] CPU: Testing write buffer coherency: ok [ 0.025505] ftrace: allocating 16357 entries in 32 pages [ 0.049506] Setting up static identity map for 0x3b1e18 - 0x3b1e70 [ 0.053008] devtmpfs: initialized [ 0.054793] pinctrl core: initialized pinctrl subsystem [ 0.055284] regulator-dummy: no parameters [ 0.058808] NET: Registered protocol family 16 [ 0.059213] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.060247] cpuidle: using governor ladder [ 0.060272] cpuidle: using governor menu [ 0.060496] Feroceon L2: Enabling L2 [ 0.060537] Feroceon L2: Cache support initialised. [ 0.060884] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.065171] No ATAGs? [ 0.069194] platform regulators:regulator@1: Driver reg-fixed-voltage requests probe deferral [ 0.070339] Switched to clocksource orion_clocksource [ 0.092514] NET: Registered protocol family 2 [ 0.093494] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.093531] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.093561] TCP: Hash tables configured (established 2048 bind 2048) [ 0.093625] TCP: reno registered [ 0.093637] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.093658] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.093837] NET: Registered protocol family 1 [ 0.094132] Unpacking initramfs... [ 1.030001] Freeing initrd memory: 10296K (c1101000 - c1b0f000) [ 1.031615] futex hash table entries: 256 (order: -1, 3072 bytes) [ 1.031689] audit: initializing netlink subsys (disabled) [ 1.031754] audit: type=2000 audit(1.024:1): initialized [ 1.032625] zbud: loaded [ 1.032882] VFS: Disk quotas dquot_6.5.2 [ 1.032931] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.033028] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.033243] msgmni has been set to 495 [ 1.035214] alg: No test for stdrng (krng) [ 1.035322] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 1.035513] io scheduler noop registered [ 1.035668] io scheduler cfq registered (default) [ 1.036879] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 1.038239] mv_xor f1060800.xor: Marvell shared XOR driver [ 1.058458] mv_xor f1060800.xor: Marvell XOR: ( xor cpy ) [ 1.078455] mv_xor f1060800.xor: Marvell XOR: ( xor cpy ) [ 1.078633] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.098452] mv_xor f1060900.xor: Marvell XOR: ( xor cpy ) [ 1.118453] mv_xor f1060900.xor: Marvell XOR: ( xor cpy ) [ 1.118900] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 1.120174] console [ttyS0] disabled [ 1.120226] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 12500000) is a 16550A [ 1.628455] console [ttyS0] enabled [ 1.633796] nand: Could not find valid ONFI parameter page; aborting [ 1.640232] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 1.646623] nand: Hynix NAND 128MiB 3,3V 8-bit [ 1.651095] nand: 128MiB, SLC, page size: 2048, OOB size: 64 [ 1.656797] Scanning device for bad blocks [ 1.738146] 3 ofpart partitions found on MTD device orion_nand [ 1.744017] Creating 3 MTD partitions on "orion_nand": [ 1.749193] 0x000000000000-0x000000100000 : "u-boot" [ 1.755382] 0x000000100000-0x000000500000 : "uImage" [ 1.761479] 0x000000500000-0x000020000000 : "root" [ 1.766316] mtd: partition "root" extends beyond the end of device "orion_nand" -- size truncated to 0x7b00000 [ 1.778160] mousedev: PS/2 mouse device common for all mice [ 2.786447] rtc-mv f1010300.rtc: internal RTC not ticking [ 2.792012] i2c /dev entries driver [ 2.796713] ledtrig-cpu: registered to indicate activity on CPUs [ 2.803113] TCP: cubic registered [ 2.806471] NET: Registered protocol family 17 [ 2.811673] registered taskstats version 1 [ 2.816879] USB Power: 5000 mV [ 2.820423] rtc_hctosys: unable to open rtc device (rtc0) [ 2.827736] Freeing unused kernel memory: 276K (c0542000 - c0587000) Loading, please wait... [ 2.902796] systemd-udevd[47]: starting version 215 [ 2.916508] random: systemd-udevd urandom read with 1 bits of entropy available [ 3.037940] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 3.053217] usbcore: registered new interface driver usbfs [ 3.091750] libphy: orion_mdio_bus: probed [ 3.097458] platform mv643xx_eth_port.0: Driver mv643xx_eth_port requests probe deferral [ 3.108219] usbcore: registered new interface driver hub [ 3.138886] usbcore: registered new device driver usb [ 3.166083] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.208801] ehci-orion: EHCI orion driver [ 3.728240] orion-ehci f1050000.ehci: EHCI Host Controller [ 3.752600] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 4.280859] orion-ehci f1050000.ehci: irq 19, io mem 0xf1050000 [ 4.295900] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:04:7b:64 [ 4.306629] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 4.316047] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 4.322896] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.330163] usb usb1: Product: EHCI Host Controller [ 4.335072] usb usb1: Manufacturer: Linux 3.16.0-4-kirkwood ehci_hcd [ 4.341463] usb usb1: SerialNumber: f1050000.ehci [ 4.347503] hub 1-0:1.0: USB hub found [ 4.351327] hub 1-0:1.0: 1 port detected [ 4.666370] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 4.804108] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 4.810861] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 4.818048] usb 1-1: Product: USB2.0 Hub [ 4.826655] hub 1-1:1.0: USB hub found [ 4.830862] hub 1-1:1.0: 4 ports detected [ 5.106365] usb 1-1.3: new high-speed USB device number 3 using orion-ehci [ 5.214485] usb 1-1.3: New USB device found, idVendor=0000, idProduct=7777 [ 5.221415] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 5.228779] usb 1-1.3: Product: Mass Storage [ 5.233082] usb 1-1.3: Manufacturer: Generic [ 5.237381] usb 1-1.3: SerialNumber: 2B2A01FE [ 5.257980] SCSI subsystem initialized [ 5.266739] usb-storage 1-1.3:1.0: USB Mass Storage device detected [ 5.273382] scsi0 : usb-storage 1-1.3:1.0 [ 5.279087] usbcore: registered new interface driver usb-storage [ 6.276706] scsi 0:0:0:0: Direct-Access Generic Flash Disk 8.07 PQ: 0 ANSI: 4 [ 6.299522] sd 0:0:0:0: [sda] 4096000000 512-byte logical blocks: (2.09 TB/1.90 TiB) [ 6.308130] sd 0:0:0:0: [sda] Write Protect is off [ 6.313878] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 6.342125] sda: sda1 sda2 [ 6.349384] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 6.359032] sd 0:0:0:0: Attached scsi generic sg0 type 0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... Begin: Assembling all MD arrays ... [ 14.569472] __nand_correct_data: uncorrectable ECC error [ 14.574859] end_request: I/O error, dev mtdblock0, sector 1920 [ 14.580968] __nand_correct_data: uncorrectable ECC error [ 14.586352] end_request: I/O error, dev mtdblock0, sector 2032 [ 14.592463] __nand_correct_data: uncorrectable ECC error [ 14.597817] __nand_correct_data: uncorrectable ECC error [ 14.603171] end_request: I/O error, dev mtdblock0, sector 2046 mdadm: No arrays found in config file or automatically Failure: failed to assemble all arrays. done. done. Begin: Running /scripts/local-premount ... [ 14.628230] PM: Starting manual resume from disk done. Begin: Waiting for root file system ... Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. [ 36.583457] random: nonblocking pool is initialized Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. done. Gave up waiting for root device. Common problems: - Boot args (cat /proc/cmdline) - Check rootdelay= (did the system wait long enough?) - Check root= (did the system wait for the right device?) - Missing modules (cat /proc/modules; ls /dev) ALERT! /dev/disk/by-label/rootfs does not exist. Dropping to a shell! modprobe: module i8042 not found in modules.dep [ 44.818651] ehci-pci: EHCI PCI platform driver [ 44.844840] uhci_hcd: USB Universal Host Controller Interface driver [ 44.861893] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 44.882161] hidraw: raw HID events driver (C) Jiri Kosina [ 44.892652] usbcore: registered new interface driver usbhid [ 44.898286] usbhid: USB HID core driver BusyBox v1.22.1 (Debian 1:1.22.0-9+deb8u1) built-in shell (ash) Enter 'help' for a list of built-in commands. /bin/sh: can't access tty; job control turned off (initramfs)
picocom v1.7 port is : /dev/ttyUSB0 flowcontrol : none baudrate is : 115200 parity is : none databits are : 8 escape is : C-a local echo is : no noinit is : no noreset is : no nolock is : no send_cmd is : sz -vv receive_cmd is : rz -vv imap is : omap is : emap is : crcrlf,delbs, Terminal ready U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:23:43 -0700) Pogo E02 SoC: Kirkwood 88F6281_A0 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 PogoE02> printenv arcNumber=3542 bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-pogo_e02.dtb ethact=egiga0 ethaddr=00:25:31:04:7B:64 if_netconsole=ping $serverip init_ide=ide reset init_mmc=mmc rescan init_usb=usb start ipaddr=192.168.86.109 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) nc_ready=0 partition=nand0,2 scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done scan_ide=ide reset scan_mmc=mmc rescan scan_usb=usb start set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_loaded=0 uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_ready_retry=15 Environment size: 3073/131068 bytes PogoE02>
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 27, 2016 03:00AM |
Admin Registered: 13 years ago Posts: 18,575 |
Quote
Updated 20 Feb 2016:
This Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 is to keep in sync with kernel Linux-4.4.0-kirkwood-tld-1.
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 27, 2016 03:04AM |
Registered: 7 years ago Posts: 310 |
PogoE02> ls usb 1:1 <DIR> 4096 . <DIR> 4096 .. <DIR> 16384 lost+found 127256496 base.tar.bz2 2840564 sheeva-2.6.33-uImage 4408698 sheeva-2.6.33-Modules.tar.gz <DIR> 4096 boot <DIR> 4096 sbin <DIR> 4096 opt <DIR> 4096 etc <DIR> 4096 dev <DIR> 4096 root <DIR> 8192 lib <DIR> 4096 mnt <DIR> 4096 var <DIR> 4096 bin <DIR> 4096 home <DIR> 4096 srv <DIR> 4096 media <DIR> 4096 proc <DIR> 4096 sys <DIR> 4096 usr <DIR> 4096 tmp <DIR> 4096 run PogoE02> ls usb 0:1 <DIR> 4096 . <DIR> 4096 .. <DIR> 16384 lost+found 18406 install_uboot_mtd0.sh PogoE02>
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 27, 2016 03:50AM |
Registered: 7 years ago Posts: 310 |
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:23:43 -0700) Pogo E02 SoC: Kirkwood 88F6281_A0 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Unknown command 'ide' - try 'help' Unknown command 'mmc' - try 'help' Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 61052928 0030cd40-01 83 Boot loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** Unknown command 'ide' - try 'help' Unknown command 'mmc' - try 'help' running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 253 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 3165342 bytes read in 403 ms (7.5 MiB/s) loading uInitrd ... 7179935 bytes read in 507 ms (13.5 MiB/s) loading DTB /boot/dts/kirkwood-pogo_e02.dtb ... 10446 bytes read in 1113 ms (8.8 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.4.0-kirkwood-tld-1 Created: 2016-07-27 8:34:09 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3165278 Bytes = 3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.4.0-kirkwood-tld-1 Created: 2016-02-19 7:33:04 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7179871 Bytes = 6.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 0f43b000, end 0fb13e5f ... OK Loading Device Tree to 0f435000, end 0f43a8cd ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine model: CloudEngines Pogoplug E02 [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10 [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 250592K/262144K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 11552K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc07d7ef4 (8000 kB) [ 0.000000] .init : 0xc07d8000 - 0xc0822000 ( 296 kB) [ 0.000000] .data : 0xc0822000 - 0xc08b169c ( 574 kB) [ 0.000000] .bss : 0xc08b169c - 0xc08ff9d0 ( 313 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000009] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.008270] Console: colour dummy device 80x30 [ 0.012836] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584) [ 0.100932] pid_max: default: 32768 minimum: 301 [ 0.105754] Security Framework initialized [ 0.110070] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.116815] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.124821] Initializing cgroup subsys io [ 0.129012] Initializing cgroup subsys devices [ 0.133582] Initializing cgroup subsys freezer [ 0.138201] Initializing cgroup subsys net_cls [ 0.142834] CPU: Testing write buffer coherency: ok [ 0.148345] Setting up static identity map for 0x8200 - 0x8258 [ 0.154580] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.163653] devtmpfs: initialized [ 0.171739] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.182224] prandom: seed boundary self test passed [ 0.191043] prandom: 100 self tests passed [ 0.195266] pinctrl core: initialized pinctrl subsystem [ 0.202040] NET: Registered protocol family 16 [ 0.207037] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.238051] cpuidle: using governor ladder [ 0.268049] cpuidle: using governor menu [ 0.272484] Feroceon L2: Enabling L2 [ 0.276195] Feroceon L2: Cache support initialised. [ 0.281602] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.297079] No ATAGs? [ 0.329557] vgaarb: loaded [ 0.332989] usbcore: registered new interface driver usbfs [ 0.338717] usbcore: registered new interface driver hub [ 0.344209] usbcore: registered new device driver usb [ 0.350491] clocksource: Switched to clocksource orion_clocksource [ 0.412539] NET: Registered protocol family 2 [ 0.417815] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.425053] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.431569] TCP: Hash tables configured (established 2048 bind 2048) [ 0.438097] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.444080] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.450685] NET: Registered protocol family 1 [ 0.455506] RPC: Registered named UNIX socket transport module. [ 0.461595] RPC: Registered udp transport module. [ 0.466409] RPC: Registered tcp transport module. [ 0.471234] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.478172] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.485894] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.492227] audit: initializing netlink subsys (disabled) [ 0.497776] audit: type=2000 audit(0.480:1): initialized [ 0.503615] Initialise system trusted keyring [ 0.508409] zbud: loaded [ 0.511366] VFS: Disk quotas dquot_6.6.0 [ 0.515442] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.523124] NFS: Registering the id_resolver key type [ 0.528314] Key type id_resolver registered [ 0.532654] Key type id_legacy registered [ 0.536794] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.543637] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.550319] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.558031] Key type big_key registered [ 0.573400] Key type asymmetric registered [ 0.577615] Asymmetric key parser 'x509' registered [ 0.582779] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.590306] io scheduler noop registered [ 0.594521] io scheduler deadline registered [ 0.598959] io scheduler cfq registered (default) [ 0.605167] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 0.613371] irq: Cannot allocate irq_descs @ IRQ32, assuming pre-allocated [ 0.620809] irq: Cannot allocate irq_descs @ IRQ64, assuming pre-allocated [ 0.628326] mv_xor f1060800.xor: Marvell shared XOR driver [ 0.671186] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 0.678836] mv_xor f1060900.xor: Marvell shared XOR driver [ 0.721177] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 0.729094] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.737012] console [ttyS0] disabled [ 0.740801] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A [ 0.749926] console [ttyS0] enabled [ 0.749926] console [ttyS0] enabled [ 0.757064] bootconsole [earlycon0] disabled [ 0.757064] bootconsole [earlycon0] disabled [ 0.767407] nand: Could not find valid ONFI parameter page; aborting [ 0.773872] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 0.780252] nand: Hynix NAND 128MiB 3,3V 8-bit [ 0.784739] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 0.792365] Scanning device for bad blocks [ 0.907992] libphy: Fixed MDIO Bus: probed [ 0.912533] libphy: orion_mdio_bus: probed [ 0.917355] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 2.001115] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:04:7b:64 [ 2.009987] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.016607] ehci-pci: EHCI PCI platform driver [ 2.021167] ehci-orion: EHCI orion driver [ 2.025372] orion-ehci f1050000.ehci: EHCI Host Controller [ 2.030939] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 2.038792] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 2.060581] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 2.066850] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.073707] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.080985] usb usb1: Product: EHCI Host Controller [ 2.085884] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd [ 2.092546] usb usb1: SerialNumber: f1050000.ehci [ 2.098009] hub 1-0:1.0: USB hub found [ 2.101873] hub 1-0:1.0: 1 port detected [ 2.106789] mousedev: PS/2 mouse device common for all mice [ 2.420525] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 2.572181] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 2.578925] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 2.586132] usb 1-1: Product: USB2.0 Hub [ 2.591029] hub 1-1:1.0: USB hub found [ 2.595176] hub 1-1:1.0: 4 ports detected [ 2.880519] usb 1-1.2: new high-speed USB device number 3 using orion-ehci [ 2.991550] usb 1-1.2: New USB device found, idVendor=0781, idProduct=5575 [ 2.998471] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.005851] usb 1-1.2: Product: Cruzer Glide [ 3.010142] usb 1-1.2: Manufacturer: SanDisk [ 3.014452] usb 1-1.2: SerialNumber: 4C531001480325118324 [ 3.120524] rtc-mv f1010300.rtc: internal RTC not ticking [ 3.126158] i2c /dev entries driver [ 3.130983] hidraw: raw HID events driver (C) Jiri Kosina [ 3.136814] drop_monitor: Initializing network drop monitor service [ 3.143396] NET: Registered protocol family 17 [ 3.148128] Key type dns_resolver registered [ 3.153327] registered taskstats version 1 [ 3.157491] Loading compiled-in X.509 certificates [ 3.162401] zswap: loaded using pool lzo/zbud [ 3.167887] Key type encrypted registered [ 3.172485] hctosys: unable to open rtc device (rtc0) [ 3.179011] Waiting 10 sec before mounting root device... [ 13.190751] VFS: Cannot open root device "sda1" or unknown-block(0,0): error -6 [ 13.198099] Please append a correct "root=" boot option; here are the available partitions: [ 13.206548] 1f00 131072 mtdblock0 (driver?) [ 13.211680] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 13.219981] CPU: 0 PID: 1 Comm: swapper Not tainted 4.4.0-kirkwood-tld-1 #1 [ 13.226969] Hardware name: Marvell Kirkwood (Flattened Device Tree) [ 13.233289] [<c0016784>] (unwind_backtrace) from [<c00129f8>] (show_stack+0x10/0x14) [ 13.241071] [<c00129f8>] (show_stack) from [<c00c2200>] (panic+0x80/0x214) [ 13.247989] [<c00c2200>] (panic) from [<c07d9280>] (mount_block_root+0x204/0x24c) [ 13.255510] [<c07d9280>] (mount_block_root) from [<c07d93b4>] (mount_root+0xec/0x118) [ 13.263384] [<c07d93b4>] (mount_root) from [<c07d9504>] (prepare_namespace+0x124/0x184) [ 13.271424] [<c07d9504>] (prepare_namespace) from [<c07d8e9c>] (kernel_init_freeable+0x208/0x258) [ 13.280349] [<c07d8e9c>] (kernel_init_freeable) from [<c05b16b4>] (kernel_init+0x8/0xe4) [ 13.288482] [<c05b16b4>] (kernel_init) from [<c000f090>] (ret_from_fork+0x14/0x24) [ 13.296093] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 80.190517] random: nonblocking pool is initialized
root@debian-laptop:/media/feas/rootfs# wget http://www.dropbox.com/s/qt2v378sm3j0loe/Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 --2016-07-27 05:19:35-- http://www.dropbox.com/s/qt2v378sm3j0loe/Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 Resolving www.dropbox.com (www.dropbox.com)... 162.125.4.1 Connecting to www.dropbox.com (www.dropbox.com)|162.125.4.1|:80... connected. HTTP request sent, awaiting response... 301 Moved Permanently Location: https://www.dropbox.com/s/qt2v378sm3j0loe/Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 [following] --2016-07-27 05:19:35-- https://www.dropbox.com/s/qt2v378sm3j0loe/Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 Connecting to www.dropbox.com (www.dropbox.com)|162.125.4.1|:443... connected. HTTP request sent, awaiting response... 302 Found Location: https://dl.dropboxusercontent.com/content_link/IAJeL0FnJM3EuxkX3nrkvXZMgYh5jg9EAhdr2jrm0BRWMn1TTlgMP7ARyRbRoDLO/file [following] --2016-07-27 05:19:35-- https://dl.dropboxusercontent.com/content_link/IAJeL0FnJM3EuxkX3nrkvXZMgYh5jg9EAhdr2jrm0BRWMn1TTlgMP7ARyRbRoDLO/file Resolving dl.dropboxusercontent.com (dl.dropboxusercontent.com)... 45.58.70.37 Connecting to dl.dropboxusercontent.com (dl.dropboxusercontent.com)|45.58.70.37|:443... connected. HTTP request sent, awaiting response... 200 OK Length: 143314034 (137M) [application/octet-stream] Saving to: ‘Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2’ Debian-4.4.0-kirkwood-tld-1-r 100%[=================================================>] 136.67M 5.98MB/s in 28s 2016-07-27 05:20:04 (4.82 MB/s) - ‘Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2’ saved [143314034/143314034] root@debian-laptop:/media/feas/rootfs# root@debian-laptop:/media/feas/rootfs# ls Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 lost+found root@debian-laptop:/media/feas/rootfs# md5sum Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 9f957e1dc5a36f90a285ab4615cb02fd Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 root@debian-laptop:/media/feas/rootfs# sha256sum Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 d33349118e34bd078ca635cd2d6776f3e312accfc77d29da5870b9980add5c36 Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 root@debian-laptop:/media/feas/rootfs# root@debian-laptop:/media/feas/rootfs# tar -xjf Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 root@debian-laptop:/media/feas/rootfs# nano etc/fstab root@debian-laptop:/media/feas/rootfs# cat etc/fstab # /etc/fstab: static file system information. # # <file system> <mount point> <type> <options> <dump> <pass> /dev/root / ext3 noatime,errors=remount-ro 0 1 tmpfs /tmp tmpfs defaults 0 0 root@debian-laptop:/media/feas/rootfs# cd boot root@debian-laptop:/media/feas/rootfs/boot# ls config-4.4.0-kirkwood-tld-1 linux-headers-4.4.0-kirkwood-tld-1_1.0_armel.deb uInitrd dts System.map-4.4.0-kirkwood-tld-1 vmlinuz-4.4.0-kirkwood-tld-1 initrd.img-4.4.0-kirkwood-tld-1 uImage zImage-4.4.0-kirkwood-tld-1 root@debian-laptop:/media/feas/rootfs/boot# cp -a zImage-4.4.0-kirkwood-tld-1 zImage.fdt root@debian-laptop:/media/feas/rootfs/boot# cd dts root@debian-laptop:/media/feas/rootfs/boot/dts# ls kirkwood-asus_m25.dtb kirkwood-ib62x0.dtb kirkwood-nsa320s.dtb kirkwood-b3.dtb kirkwood-iconnect.dtb kirkwood-nsa325.dtb kirkwood-blackarmor-nas220.dtb kirkwood-iomega_ix2_200.dtb kirkwood-openblocks_a6.dtb kirkwood-cloudbox.dtb kirkwood-iomega_ix4_200d.dtb kirkwood-openblocks_a7.dtb kirkwood-d2net.dtb kirkwood-is2.dtb kirkwood-openrd-base.dtb kirkwood-db-88f6281.dtb kirkwood-km_kirkwood.dtb kirkwood-openrd-client.dtb kirkwood-db-88f6282.dtb kirkwood-laplug.dtb kirkwood-openrd-ultimate.dtb kirkwood-dir665.dtb kirkwood-lschlv2.dtb kirkwood-pogo_e02.dtb kirkwood-dns320.dtb kirkwood-lswvl.dtb kirkwood-pogoplug_v4.dtb kirkwood-dns325.dtb kirkwood-lswxl.dtb kirkwood-qizhitong_501m_v2.dtb kirkwood-dockstar.dtb kirkwood-lsxhl.dtb kirkwood-rd88f6192.dtb kirkwood-dreamplug.dtb kirkwood-mplcec4.dtb kirkwood-rd88f6281-a0.dtb kirkwood-ds109.dtb kirkwood-mv88f6281gtw-ge.dtb kirkwood-rd88f6281-a1.dtb kirkwood-ds110jv10.dtb kirkwood-nas2big.dtb kirkwood-rd88f6281-a.dtb kirkwood-ds111.dtb kirkwood-net2big.dtb kirkwood-rd88f6281-z0.dtb kirkwood-ds209.dtb kirkwood-net5big.dtb kirkwood-rs212.dtb kirkwood-ds210.dtb kirkwood-netgear_readynas_duo_v2.dtb kirkwood-rs409.dtb kirkwood-ds212.dtb kirkwood-netgear_readynas_nv+_v2.dtb kirkwood-rs411.dtb kirkwood-ds212j.dtb kirkwood-netgear_stora_ms2000.dtb kirkwood-sheevaplug.dtb kirkwood-ds409.dtb kirkwood-ns2.dtb kirkwood-sheevaplug-esata.dtb kirkwood-ds409slim.dtb kirkwood-ns2lite.dtb kirkwood-t5325.dtb kirkwood-ds411.dtb kirkwood-ns2max.dtb kirkwood-topkick.dtb kirkwood-ds411j.dtb kirkwood-ns2mini.dtb kirkwood-ts219-6281.dtb kirkwood-ds411slim.dtb kirkwood-nsa310a.dtb kirkwood-ts219-6282.dtb kirkwood-goflexhome.dtb kirkwood-nsa310.dtb kirkwood-ts419-6281.dtb kirkwood-goflexnet.dtb kirkwood-nsa310s.dtb kirkwood-ts419-6282.dtb kirkwood-guruplug-server-plus.dtb kirkwood-nsa320.dtb root@debian-laptop:/media/feas/rootfs/boot/dts# cd .. root@debian-laptop:/media/feas/rootfs/boot# cat dts/kirkwood-pogo_e02.dtb >> zImage.fdt root@debian-laptop:/media/feas/rootfs/boot# mv uImage uImage.orig root@debian-laptop:/media/feas/rootfs/boot# mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-4.4.0-kirkwood-tld-1 -d zImage.fdt uImage Image Name: Linux-4.4.0-kirkwood-tld-1 Created: Wed Jul 27 05:29:52 2016 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3165278 Bytes = 3091.09 kB = 3.02 MB Load Address: 00008000 Entry Point: 00008000 root@debian-laptop:/media/feas/rootfs/boot# sync root@debian-laptop:/media/feas/rootfs/boot# ls -la total 39200 drwxr-xr-x 3 root root 4096 Jul 27 05:29 . drwxr-xr-x 21 root root 4096 Feb 16 2015 .. -rw-r--r-- 1 root root 140949 Jan 25 2016 config-4.4.0-kirkwood-tld-1 drwxr-xr-x 2 root root 4096 Jan 26 2016 dts -rw-r--r-- 1 root root 7179871 Feb 19 01:36 initrd.img-4.4.0-kirkwood-tld-1 -rw-r--r-- 1 root root 7511582 Jan 26 2016 linux-headers-4.4.0-kirkwood-tld-1_1.0_armel.deb -rw------- 1 root root 2240040 Jan 26 2016 System.map-4.4.0-kirkwood-tld-1 -rw-r--r-- 1 root root 3165342 Jul 27 05:31 uImage -rw-r--r-- 1 root root 3154896 Feb 19 00:55 uImage.orig -rw-r--r-- 1 root root 7179935 Feb 19 02:33 uInitrd -rw------- 1 root root 3154832 Jan 26 2016 vmlinuz-4.4.0-kirkwood-tld-1 -rwxr-xr-x 1 root root 3154832 Jan 25 2016 zImage-4.4.0-kirkwood-tld-1 -rwxr-xr-x 1 root root 3165278 Jul 27 05:29 zImage.fdt root@debian-laptop:/media/feas/rootfs/boot#
picocom v1.7 port is : /dev/ttyUSB0 flowcontrol : none baudrate is : 115200 parity is : none databits are : 8 escape is : C-a local echo is : no noinit is : no noreset is : no nolock is : no send_cmd is : sz -vv receive_cmd is : rz -vv imap is : omap is : emap is : crcrlf,delbs, Terminal ready 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Unknown command 'ide' - try 'help' Unknown command 'mmc' - try 'help' Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 61052928 0030cd40-01 83 Boot loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** Unknown command 'ide' - try 'help' Unknown command 'mmc' - try 'help' running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 242 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 3165342 bytes read in 388 ms (7.8 MiB/s) loading uInitrd ... 7179935 bytes read in 496 ms (13.8 MiB/s) loading DTB /boot/dts/kirkwood-pogo_e02.dtb ... 10446 bytes read in 1102 ms (8.8 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.4.0-kirkwood-tld-1 Created: 2016-07-27 9:29:52 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3165278 Bytes = 3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.4.0-kirkwood-tld-1 Created: 2016-02-19 7:33:04 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7179871 Bytes = 6.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 0f43b000, end 0fb13e5f ... OK Loading Device Tree to 0f435000, end 0f43a8cd ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine model: CloudEngines Pogoplug E02 [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10 [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 250592K/262144K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 11552K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc07d7ef4 (8000 kB) [ 0.000000] .init : 0xc07d8000 - 0xc0822000 ( 296 kB) [ 0.000000] .data : 0xc0822000 - 0xc08b169c ( 574 kB) [ 0.000000] .bss : 0xc08b169c - 0xc08ff9d0 ( 313 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000009] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.008270] Console: colour dummy device 80x30 [ 0.012836] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584) [ 0.100931] pid_max: default: 32768 minimum: 301 [ 0.105756] Security Framework initialized [ 0.110072] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.116815] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.124811] Initializing cgroup subsys io [ 0.128994] Initializing cgroup subsys devices [ 0.133564] Initializing cgroup subsys freezer [ 0.138180] Initializing cgroup subsys net_cls [ 0.142807] CPU: Testing write buffer coherency: ok [ 0.148321] Setting up static identity map for 0x8200 - 0x8258 [ 0.154553] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.163630] devtmpfs: initialized [ 0.171692] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.182175] prandom: seed boundary self test passed [ 0.190989] prandom: 100 self tests passed [ 0.195215] pinctrl core: initialized pinctrl subsystem [ 0.202000] NET: Registered protocol family 16 [ 0.206992] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.238051] cpuidle: using governor ladder [ 0.268051] cpuidle: using governor menu [ 0.272483] Feroceon L2: Enabling L2 [ 0.276195] Feroceon L2: Cache support initialised. [ 0.281601] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.297080] No ATAGs? [ 0.329556] vgaarb: loaded [ 0.332989] usbcore: registered new interface driver usbfs [ 0.338717] usbcore: registered new interface driver hub [ 0.344210] usbcore: registered new device driver usb [ 0.350492] clocksource: Switched to clocksource orion_clocksource [ 0.412551] NET: Registered protocol family 2 [ 0.417817] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.425050] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.431569] TCP: Hash tables configured (established 2048 bind 2048) [ 0.438098] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.444082] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.450685] NET: Registered protocol family 1 [ 0.455496] RPC: Registered named UNIX socket transport module. [ 0.461576] RPC: Registered udp transport module. [ 0.466391] RPC: Registered tcp transport module. [ 0.471217] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.478149] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.485873] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.492209] audit: initializing netlink subsys (disabled) [ 0.497759] audit: type=2000 audit(0.480:1): initialized [ 0.503597] Initialise system trusted keyring [ 0.508400] zbud: loaded [ 0.511356] VFS: Disk quotas dquot_6.6.0 [ 0.515433] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.523117] NFS: Registering the id_resolver key type [ 0.528305] Key type id_resolver registered [ 0.532647] Key type id_legacy registered [ 0.536785] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.543627] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.550315] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.558021] Key type big_key registered [ 0.573390] Key type asymmetric registered [ 0.577606] Asymmetric key parser 'x509' registered [ 0.582769] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.590297] io scheduler noop registered [ 0.594513] io scheduler deadline registered [ 0.598950] io scheduler cfq registered (default) [ 0.605159] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 0.613366] irq: Cannot allocate irq_descs @ IRQ32, assuming pre-allocated [ 0.620806] irq: Cannot allocate irq_descs @ IRQ64, assuming pre-allocated [ 0.628327] mv_xor f1060800.xor: Marvell shared XOR driver [ 0.671182] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 0.678836] mv_xor f1060900.xor: Marvell shared XOR driver [ 0.721179] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 0.729091] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.737017] console [ttyS0] disabled [ 0.740811] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A [ 0.749935] console [ttyS0] enabled [ 0.749935] console [ttyS0] enabled [ 0.757073] bootconsole [earlycon0] disabled [ 0.757073] bootconsole [earlycon0] disabled [ 0.767420] nand: Could not find valid ONFI parameter page; aborting [ 0.773889] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 0.780270] nand: Hynix NAND 128MiB 3,3V 8-bit [ 0.784756] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 0.792383] Scanning device for bad blocks [ 0.908026] libphy: Fixed MDIO Bus: probed [ 0.912571] libphy: orion_mdio_bus: probed [ 0.917420] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 2.001140] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:04:7b:64 [ 2.010015] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.016632] ehci-pci: EHCI PCI platform driver [ 2.021193] ehci-orion: EHCI orion driver [ 2.025400] orion-ehci f1050000.ehci: EHCI Host Controller [ 2.030966] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 2.038817] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 2.060582] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 2.066849] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.073705] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.080984] usb usb1: Product: EHCI Host Controller [ 2.085882] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd [ 2.092545] usb usb1: SerialNumber: f1050000.ehci [ 2.098006] hub 1-0:1.0: USB hub found [ 2.101874] hub 1-0:1.0: 1 port detected [ 2.106787] mousedev: PS/2 mouse device common for all mice [ 2.420527] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 2.572081] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 2.578829] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 2.586036] usb 1-1: Product: USB2.0 Hub [ 2.590938] hub 1-1:1.0: USB hub found [ 2.595077] hub 1-1:1.0: 4 ports detected [ 2.880519] usb 1-1.3: new high-speed USB device number 3 using orion-ehci [ 2.991451] usb 1-1.3: New USB device found, idVendor=0781, idProduct=5575 [ 2.998373] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.005755] usb 1-1.3: Product: Cruzer Glide [ 3.010045] usb 1-1.3: Manufacturer: SanDisk [ 3.014357] usb 1-1.3: SerialNumber: 4C531001480325118324 [ 3.120524] rtc-mv f1010300.rtc: internal RTC not ticking [ 3.126156] i2c /dev entries driver [ 3.130982] hidraw: raw HID events driver (C) Jiri Kosina [ 3.136814] drop_monitor: Initializing network drop monitor service [ 3.143394] NET: Registered protocol family 17 [ 3.148132] Key type dns_resolver registered [ 3.153326] registered taskstats version 1 [ 3.157491] Loading compiled-in X.509 certificates [ 3.162402] zswap: loaded using pool lzo/zbud [ 3.167889] Key type encrypted registered [ 3.172489] hctosys: unable to open rtc device (rtc0) [ 3.179007] Waiting 10 sec before mounting root device... [ 13.190753] VFS: Cannot open root device "sda1" or unknown-block(0,0): error -6 [ 13.198099] Please append a correct "root=" boot option; here are the available partitions: [ 13.206550] 1f00 131072 mtdblock0 (driver?) [ 13.211681] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 13.219982] CPU: 0 PID: 1 Comm: swapper Not tainted 4.4.0-kirkwood-tld-1 #1 [ 13.226970] Hardware name: Marvell Kirkwood (Flattened Device Tree) [ 13.233290] [<c0016784>] (unwind_backtrace) from [<c00129f8>] (show_stack+0x10/0x14) [ 13.241073] [<c00129f8>] (show_stack) from [<c00c2200>] (panic+0x80/0x214) [ 13.247988] [<c00c2200>] (panic) from [<c07d9280>] (mount_block_root+0x204/0x24c) [ 13.255511] [<c07d9280>] (mount_block_root) from [<c07d93b4>] (mount_root+0xec/0x118) [ 13.263384] [<c07d93b4>] (mount_root) from [<c07d9504>] (prepare_namespace+0x124/0x184) [ 13.271433] [<c07d9504>] (prepare_namespace) from [<c07d8e9c>] (kernel_init_freeable+0x208/0x258) [ 13.280358] [<c07d8e9c>] (kernel_init_freeable) from [<c05b16b4>] (kernel_init+0x8/0xe4) [ 13.288492] [<c05b16b4>] (kernel_init) from [<c000f090>] (ret_from_fork+0x14/0x24) [ 13.296102] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 80.190518] random: nonblocking pool is initialized
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 27, 2016 05:37AM |
Registered: 7 years ago Posts: 310 |
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 27, 2016 10:36AM |
Registered: 7 years ago Posts: 310 |
mtdparts had an extra "mtdparts=" so reset that env
[ 1.749193] 0x000000000000-0x000000100000 : "u-boot" [ 1.755382] 0x000000100000-0x000000500000 : "uImage" [ 1.761479] 0x000000500000-0x000020000000 : "root"to
dev: size erasesize name mtd0: 00100000 00020000 "u-boot" mtd1: 00400000 00020000 "uImage" mtd2: 02000000 00020000 "rootfs" mtd3: 0db00000 00020000 "data"
oot@debian:~# uname -a Linux debian 4.4.0-kirkwood-tld-1 #1 PREEMPT Mon Jan 25 20:35:24 PST 2016 armv5tel GNU/Linux
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 27, 2016 11:10AM |
Registered: 7 years ago Posts: 310 |
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 27, 2016 12:23PM |
Admin Registered: 13 years ago Posts: 18,575 |
[ 0.000000] Kernel command line: console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 27, 2016 12:25PM |
Admin Registered: 13 years ago Posts: 18,575 |
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 27, 2016 12:51PM |
Registered: 7 years ago Posts: 310 |
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:23:43 -0700) Pogo E02 SoC: Kirkwood 88F6281_A0 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Unknown command 'ide' - try 'help' Unknown command 'mmc' - try 'help' Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 61052928 0030cd40-01 83 Boot loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** Unknown command 'ide' - try 'help' Unknown command 'mmc' - try 'help' running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 242 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 3154896 bytes read in 387 ms (7.8 MiB/s) loading uInitrd ... 7179935 bytes read in 496 ms (13.8 MiB/s) loading DTB /boot/dts/kirkwood-pogo_e02.dtb ... 10446 bytes read in 1102 ms (8.8 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.4.0-kirkwood-tld-1 Created: 2016-02-19 5:55:25 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3154832 Bytes = 3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.4.0-kirkwood-tld-1 Created: 2016-02-19 7:33:04 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7179871 Bytes = 6.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 0f43b000, end 0fb13e5f ... OK Loading Device Tree to 0f435000, end 0f43a8cd ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine model: CloudEngines Pogoplug E02 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 243576K/262144K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 18568K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc07d7ef4 (8000 kB) [ 0.000000] .init : 0xc07d8000 - 0xc0822000 ( 296 kB) [ 0.000000] .data : 0xc0822000 - 0xc08b169c ( 574 kB) [ 0.000000] .bss : 0xc08b169c - 0xc08ff9d0 ( 313 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000009] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000326] Console: colour dummy device 80x30 [ 0.000357] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584) [ 0.090104] pid_max: default: 32768 minimum: 301 [ 0.090219] Security Framework initialized [ 0.090296] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090316] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.091118] Initializing cgroup subsys io [ 0.091152] Initializing cgroup subsys devices [ 0.091177] Initializing cgroup subsys freezer [ 0.091210] Initializing cgroup subsys net_cls [ 0.091295] CPU: Testing write buffer coherency: ok [ 0.091773] Setting up static identity map for 0x8200 - 0x8258 [ 0.092076] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.095865] devtmpfs: initialized [ 0.100512] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.100986] prandom: seed boundary self test passed [ 0.104745] prandom: 100 self tests passed [ 0.104773] pinctrl core: initialized pinctrl subsystem [ 0.106181] NET: Registered protocol family 16 [ 0.106636] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.130107] cpuidle: using governor ladder [ 0.160106] cpuidle: using governor menu [ 0.160524] Feroceon L2: Enabling L2 [ 0.160570] Feroceon L2: Cache support initialised. [ 0.160955] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.165858] No ATAGs? [ 0.201615] vgaarb: loaded [ 0.201992] usbcore: registered new interface driver usbfs [ 0.202073] usbcore: registered new interface driver hub [ 0.202137] usbcore: registered new device driver usb [ 0.203243] clocksource: Switched to clocksource orion_clocksource [ 0.259069] NET: Registered protocol family 2 [ 0.259888] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.259927] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.259958] TCP: Hash tables configured (established 2048 bind 2048) [ 0.260032] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.260056] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.260252] NET: Registered protocol family 1 [ 0.260668] RPC: Registered named UNIX socket transport module. [ 0.260681] RPC: Registered udp transport module. [ 0.260688] RPC: Registered tcp transport module. [ 0.260696] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.260983] Unpacking initramfs... [ 0.906705] Freeing initrd memory: 7012K (cf43b000 - cfb14000) [ 0.906835] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.907951] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.908024] audit: initializing netlink subsys (disabled) [ 0.908080] audit: type=2000 audit(0.900:1): initialized [ 0.908444] Initialise system trusted keyring [ 0.908839] zbud: loaded [ 0.909140] VFS: Disk quotas dquot_6.6.0 [ 0.909200] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.909757] NFS: Registering the id_resolver key type [ 0.909798] Key type id_resolver registered [ 0.909808] Key type id_legacy registered [ 0.909834] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.909850] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.910075] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.910605] Key type big_key registered [ 0.930982] Key type asymmetric registered [ 0.931006] Asymmetric key parser 'x509' registered [ 0.931107] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.931129] io scheduler noop registered [ 0.931145] io scheduler deadline registered [ 0.931209] io scheduler cfq registered (default) [ 0.932581] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 0.933456] irq: Cannot allocate irq_descs @ IRQ32, assuming pre-allocated [ 0.933909] irq: Cannot allocate irq_descs @ IRQ64, assuming pre-allocated [ 0.934451] mv_xor f1060800.xor: Marvell shared XOR driver [ 0.973951] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 0.974187] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.013932] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.014426] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 1.015858] console [ttyS0] disabled [ 1.015923] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A [ 1.616984] console [ttyS0] enabled [ 1.622107] nand: Could not find valid ONFI parameter page; aborting [ 1.628573] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 1.634970] nand: Hynix NAND 128MiB 3,3V 8-bit [ 1.639437] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.647066] Scanning device for bad blocks [ 1.766919] libphy: Fixed MDIO Bus: probed [ 1.771380] libphy: orion_mdio_bus: probed [ 1.780410] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 2.863899] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:04:7b:64 [ 2.872785] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.879401] ehci-pci: EHCI PCI platform driver [ 2.883960] ehci-orion: EHCI orion driver [ 2.888169] orion-ehci f1050000.ehci: EHCI Host Controller [ 2.893742] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 2.901598] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 2.923277] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 2.929563] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.936419] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.943698] usb usb1: Product: EHCI Host Controller [ 2.948597] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd [ 2.955260] usb usb1: SerialNumber: f1050000.ehci [ 2.960725] hub 1-0:1.0: USB hub found [ 2.964586] hub 1-0:1.0: 1 port detected [ 2.969495] mousedev: PS/2 mouse device common for all mice [ 3.283277] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 3.434855] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 3.441604] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 3.448811] usb 1-1: Product: USB2.0 Hub [ 3.453715] hub 1-1:1.0: USB hub found [ 3.457856] hub 1-1:1.0: 4 ports detected [ 3.743270] usb 1-1.3: new high-speed USB device number 3 using orion-ehci [ 3.854226] usb 1-1.3: New USB device found, idVendor=0781, idProduct=5575 [ 3.861149] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.868532] usb 1-1.3: Product: Cruzer Glide [ 3.872821] usb 1-1.3: Manufacturer: SanDisk [ 3.877131] usb 1-1.3: SerialNumber: 4C531001480325118324 [ 3.983274] rtc-mv f1010300.rtc: internal RTC not ticking [ 3.988905] i2c /dev entries driver [ 3.993741] hidraw: raw HID events driver (C) Jiri Kosina [ 3.999577] drop_monitor: Initializing network drop monitor service [ 4.006165] NET: Registered protocol family 17 [ 4.010895] Key type dns_resolver registered [ 4.016102] registered taskstats version 1 [ 4.020266] Loading compiled-in X.509 certificates [ 4.025169] zswap: loaded using pool lzo/zbud [ 4.038502] Key type encrypted registered [ 4.043091] hctosys: unable to open rtc device (rtc0) [ 4.050659] Freeing unused kernel memory: 296K (c07d8000 - c0822000) Loading, please wait... [ 4.128358] systemd-udevd[81]: starting version 215 [ 4.145483] random: systemd-udevd urandom read with 7 bits of entropy available [ 4.292413] SCSI subsystem initialized [ 4.339605] usb-storage 1-1.3:1.0: USB Mass Storage device detected [ 4.390288] scsi host0: usb-storage 1-1.3:1.0 [ 4.402447] usbcore: registered new interface driver usb-storage [ 4.430453] usbcore: registered new interface driver uas [ 5.394330] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Glide 1.27 PQ: 0 ANSI: 6 [ 5.411420] sd 0:0:0:0: [sda] 61056064 512-byte logical blocks: (31.2 GB/29.1 GiB) [ 5.421521] sd 0:0:0:0: [sda] Write Protect is off [ 5.427139] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 5.443519] sda: sda1 [ 5.449389] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 5.459091] sd 0:0:0:0: Attached scsi generic sg0 type 0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. modprobe: module ext3 not found in modules.dep Begin: Checking root file system ... fsck from util-linux 2.25.2 fsck: error 2 (No such file or directory) while executing fsck.ext3 for /dev/sda1 fsck exited with status code 8 done. Warning: File system check failed but did not detect errors [ 19.684064] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 19.704687] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 21.055785] systemd-udevd[289]: starting version 215 . ok [ ok ] Synthesizing the initial hotplug events...done. [....] Waiting for /dev to be fully populated...[ 21.496147] orion_wdt: Initial timeout 21 sec [ 21.534346] marvell-cesa: probe of f1030000.crypto failed with error -524 done. [ 22.023323] random: nonblocking pool is initialized [ ok ] Activating swap...done. [ 22.426890] EXT4-fs (sda1): re-mounted. Opts: (null) [....] Checking root file system...fsck from util-linux 2.25.2 rootfs: clean, 15980/1908736 files, 319889/7631616 blocks done. [ 22.644856] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ ok ] Activating lvm and md swap...done. [....] Checking file systems...fsck from util-linux 2.25.2 done. [ ok ] Loading kernel modules...done. [ ok ] Cleaning up temporary files... /tmp. [ ok ] Mounting local filesystems...done. [ ok ] Activating swapfile swap...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables ...done. [ 25.189428] NET: Registered protocol family 10 [ 26.367854] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1 Copyright 2004-2014 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:25:31:04:7b:64 Sending on LPF/eth0/00:25:31:04:7b:64 Sending on Socket/fallback DHCPREQUEST on eth0 to 255.255.255.255 port 67 [ 28.669731] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 28.679662] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPACK from 192.168.86.1 bound to 192.168.86.109 -- renewal in 42110 seconds. done. [ ok ] Starting rpcbind daemon.... [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1225 (syslogd) . ok [ ok ] Starting periodic command scheduler: cron. [ ok ] Starting system message bus: dbus. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1227 (klogd) . ok [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [ ok ] Starting NFS common utilities: statd idmapd. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. ERROR No file(s) found for glob /var/log/auth.log ERROR Failed during configuration: Have not found any log file for ssh jail [ ok ] Starting virtual private network daemon:. [ ok ] Starting OpenBSD Secure Shell server: sshd. Debian GNU/Linux 8 debian ttyS0 debian login:
root@debian:~# uname -a Linux debian 4.4.0-kirkwood-tld-1 #1 PREEMPT Mon Jan 25 20:35:24 PST 2016 armv5tel GNU/Linux
root@debian:~# dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine model: CloudEngines Pogoplug E02 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 65536 [ 0.000000] free_area_init_node: node 0, pgdat c08a06b4, node_mem_map cfdf9000 [ 0.000000] Normal zone: 512 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65536 pages, LIFO batch:15 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 243576K/262144K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 18568K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc07d7ef4 (8000 kB) .init : 0xc07d8000 - 0xc0822000 ( 296 kB) .data : 0xc0822000 - 0xc08b169c ( 574 kB) .bss : 0xc08b169c - 0xc08ff9d0 ( 313 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000009] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000326] Console: colour dummy device 80x30 [ 0.000357] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584) [ 0.090104] pid_max: default: 32768 minimum: 301 [ 0.090219] Security Framework initialized [ 0.090296] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090316] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.091117] Initializing cgroup subsys io [ 0.091152] Initializing cgroup subsys devices [ 0.091177] Initializing cgroup subsys freezer [ 0.091210] Initializing cgroup subsys net_cls [ 0.091295] CPU: Testing write buffer coherency: ok [ 0.091774] Setting up static identity map for 0x8200 - 0x8258 [ 0.092076] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.095865] devtmpfs: initialized [ 0.100516] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.100988] prandom: seed boundary self test passed [ 0.104747] prandom: 100 self tests passed [ 0.104772] pinctrl core: initialized pinctrl subsystem [ 0.106183] NET: Registered protocol family 16 [ 0.106638] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.130109] cpuidle: using governor ladder [ 0.160108] cpuidle: using governor menu [ 0.160526] Feroceon L2: Enabling L2 [ 0.160573] Feroceon L2: Cache support initialised. [ 0.160956] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.165858] No ATAGs? [ 0.201606] vgaarb: loaded [ 0.201985] usbcore: registered new interface driver usbfs [ 0.202067] usbcore: registered new interface driver hub [ 0.202130] usbcore: registered new device driver usb [ 0.203239] clocksource: Switched to clocksource orion_clocksource [ 0.259049] NET: Registered protocol family 2 [ 0.259873] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.259912] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.259944] TCP: Hash tables configured (established 2048 bind 2048) [ 0.260018] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.260042] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.260239] NET: Registered protocol family 1 [ 0.260654] RPC: Registered named UNIX socket transport module. [ 0.260667] RPC: Registered udp transport module. [ 0.260675] RPC: Registered tcp transport module. [ 0.260683] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.260703] PCI: CLS 0 bytes, default 32 [ 0.260968] Unpacking initramfs... [ 0.906752] Freeing initrd memory: 7012K (cf43b000 - cfb14000) [ 0.906882] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.907994] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.908067] audit: initializing netlink subsys (disabled) [ 0.908122] audit: type=2000 audit(0.900:1): initialized [ 0.908485] Initialise system trusted keyring [ 0.908880] zbud: loaded [ 0.909181] VFS: Disk quotas dquot_6.6.0 [ 0.909242] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.909801] NFS: Registering the id_resolver key type [ 0.909843] Key type id_resolver registered [ 0.909852] Key type id_legacy registered [ 0.909879] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.909894] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.910119] jffs2: version 2.2. (NAND) (SUMMARY) \xffffffc2\xffffffa9 2001-2006 Red Hat, Inc. [ 0.910644] Key type big_key registered [ 0.931030] Key type asymmetric registered [ 0.931053] Asymmetric key parser 'x509' registered [ 0.931153] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.931175] io scheduler noop registered [ 0.931191] io scheduler deadline registered [ 0.931255] io scheduler cfq registered (default) [ 0.932623] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 0.933501] irq: Cannot allocate irq_descs @ IRQ32, assuming pre-allocated [ 0.933950] irq: Cannot allocate irq_descs @ IRQ64, assuming pre-allocated [ 0.934492] mv_xor f1060800.xor: Marvell shared XOR driver [ 0.973947] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 0.974183] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.013923] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.014423] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 1.015850] console [ttyS0] disabled [ 1.015914] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A [ 1.616978] console [ttyS0] enabled [ 1.622104] nand: Could not find valid ONFI parameter page; aborting [ 1.628574] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 1.634971] nand: Hynix NAND 128MiB 3,3V 8-bit [ 1.639438] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.647066] Scanning device for bad blocks [ 1.766911] libphy: Fixed MDIO Bus: probed [ 1.771372] libphy: orion_mdio_bus: probed [ 1.780402] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 2.863892] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:04:7b:64 [ 2.872776] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.879391] ehci-pci: EHCI PCI platform driver [ 2.883951] ehci-orion: EHCI orion driver [ 2.888163] orion-ehci f1050000.ehci: EHCI Host Controller [ 2.893733] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 2.901592] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 2.923272] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 2.929554] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.936402] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.943682] usb usb1: Product: EHCI Host Controller [ 2.948581] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd [ 2.955243] usb usb1: SerialNumber: f1050000.ehci [ 2.960707] hub 1-0:1.0: USB hub found [ 2.964571] hub 1-0:1.0: 1 port detected [ 2.969480] mousedev: PS/2 mouse device common for all mice [ 3.283274] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 3.434847] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 3.441596] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 3.448804] usb 1-1: Product: USB2.0 Hub [ 3.453708] hub 1-1:1.0: USB hub found [ 3.457848] hub 1-1:1.0: 4 ports detected [ 3.743266] usb 1-1.3: new high-speed USB device number 3 using orion-ehci [ 3.854218] usb 1-1.3: New USB device found, idVendor=0781, idProduct=5575 [ 3.861142] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.868524] usb 1-1.3: Product: Cruzer Glide [ 3.872812] usb 1-1.3: Manufacturer: SanDisk [ 3.877123] usb 1-1.3: SerialNumber: 4C531001480325118324 [ 3.983269] rtc-mv f1010300.rtc: internal RTC not ticking [ 3.988905] i2c /dev entries driver [ 3.993740] hidraw: raw HID events driver (C) Jiri Kosina [ 3.999579] drop_monitor: Initializing network drop monitor service [ 4.006165] NET: Registered protocol family 17 [ 4.010907] Key type dns_resolver registered [ 4.016109] registered taskstats version 1 [ 4.020276] Loading compiled-in X.509 certificates [ 4.025178] zswap: loaded using pool lzo/zbud [ 4.038530] Key type encrypted registered [ 4.043114] hctosys: unable to open rtc device (rtc0) [ 4.049540] PM: Hibernation image not present or could not be loaded. [ 4.050691] Freeing unused kernel memory: 296K (c07d8000 - c0822000) [ 4.128525] systemd-udevd[81]: starting version 215 [ 4.145449] random: systemd-udevd urandom read with 7 bits of entropy available [ 4.320549] SCSI subsystem initialized [ 4.355423] usb-storage 1-1.3:1.0: USB Mass Storage device detected [ 4.392301] scsi host0: usb-storage 1-1.3:1.0 [ 4.406087] usbcore: registered new interface driver usb-storage [ 4.438038] usbcore: registered new interface driver uas [ 5.394325] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Glide 1.27 PQ: 0 ANSI: 6 [ 5.411794] sd 0:0:0:0: [sda] 61056064 512-byte logical blocks: (31.2 GB/29.1 GiB) [ 5.420887] sd 0:0:0:0: [sda] Write Protect is off [ 5.425792] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00 [ 5.426507] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 5.450253] sda: sda1 sda2 [ 5.457136] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 5.466886] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 19.684304] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 19.705321] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 21.075179] systemd-udevd[289]: starting version 215 [ 21.504716] orion_wdt: Initial timeout 21 sec [ 21.528454] marvell-cesa: probe of f1030000.crypto failed with error -524 [ 21.948284] random: nonblocking pool is initialized [ 22.485334] EXT4-fs (sda1): re-mounted. Opts: (null) [ 22.706220] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 25.268537] NET: Registered protocol family 10 [ 26.447836] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 29.036812] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 29.046744] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready root@debian:~#
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 27, 2016 01:20PM |
Registered: 7 years ago Posts: 310 |
> [ 0.000000] Kernel command line: > console=ttyS0,115200n8 earlyprintk root=/dev/sda1 > rootdelay=10 >>
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 27, 2016 02:45PM |
Admin Registered: 13 years ago Posts: 18,575 |
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; run pogo_bootcmd; reset
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 27, 2016 03:01PM |
Registered: 7 years ago Posts: 310 |
> pogo_bootcmd=if fsload uboot-original-mtd0.kwb; > then go 0x800200; fi > bootcmd=run bootcmd_uenv; run scan_disk; run > set_bootargs; run bootcmd_exec; run pogo_bootcmd; > reset >>
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 29, 2016 01:05AM |
Registered: 7 years ago Posts: 310 |
Boot and interrupt serial console, setenv pogo_bootcmd 'if fsload uboot-original-mtd0.kwb; then go 0x800200; fi' run pogo_bootcmd See if it boots back into Pogo OS.
setenv pogo_bootcmd 'if fsload uboot-original-mtd0.kwb; then go 0x800200; fi' saveenv run pogo_bootcmd
PogoE02> printenv arcNumber=3542 bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; run pogo_bootcmd; reset bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-pogo_e02.dtb ethact=egiga0 ethaddr=00:25:31:04:7B:64 if_netconsole=ping $serverip init_ide=ide reset init_mmc=mmc rescan init_usb=usb start ipaddr=192.168.86.109 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) nc_ready=0 partition=nand0,2 pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done scan_ide=ide reset scan_mmc=mmc rescan scan_usb=usb start set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_loaded=0 uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_ready_retry=15 Environment size: 3151/131068 bytes
PogoE02> run pogo_bootcmd ### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000 Scanning JFFS2 FS: ......... done. ### JFFS2 load complete: 524288 bytes loaded to 0x800000 ## Starting application at 0x00800200 ... U-Boot 1.1.4 (Sep 28 2009 - 11:55:23) Cloud Engines v2.0 (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: PPV2 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x100000, size 0x200000 Reading data from 0x2ff800 -- 100% complete. 2097152 bytes read: OK ## Booting image at 00800000 ... Image Name: Linux-2.6.22.18 Created: 2010-10-19 23:05:02 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1979140 Bytes = 1.9 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux............................................................................................................................ done, booting the kernel. [ 0.000000] Linux version 2.6.22.18 (bdietrich@buildman) (gcc version 4.2.1) #81 Tue Oct 19 16:05:00 PDT 2010 [ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177 [ 0.000000] Machine: Feroceon-KW [ 0.000000] Using UBoot passing parameters structure [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] CPU0: D VIVT write-back cache [ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] Built 1 zonelists. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro [ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes) [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.010000] Memory: 256MB 0MB 0MB 0MB = 256MB total [ 0.010000] Memory: 255872KB available (3592K code, 253K data, 124K init) [ 0.250000] Mount-cache hash table entries: 512 [ 0.250000] CPU: Testing write buffer coherency: ok [ 0.250000] NET: Registered protocol family 16 [ 0.250000] [ 0.250000] CPU Interface [ 0.250000] ------------- [ 0.250000] SDRAM_CS0 ....base 00000000, size 256MB [ 0.250000] SDRAM_CS1 ....disable [ 0.250000] SDRAM_CS2 ....disable [ 0.250000] SDRAM_CS3 ....disable [ 0.250000] PEX0_MEM ....base e8000000, size 128MB [ 0.250000] PEX0_IO ....base f2000000, size 1MB [ 0.250000] INTER_REGS ....base f1000000, size 1MB [ 0.250000] NFLASH_CS ....base fa000000, size 2MB [ 0.250000] SPI_CS ....base f4000000, size 16MB [ 0.250000] BOOT_ROM_CS ....no such [ 0.250000] DEV_BOOTCS ....no such [ 0.250000] CRYPT_ENG ....base f0000000, size 2MB [ 0.250000] [ 0.250000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21_with_rx_desc_tuned)-- SHEEVA PLUG Soc: 88F6281 A0 LE [ 0.250000] [ 0.250000] Detected Tclk 200000000 and SysClk 400000000 [ 0.250000] MV Buttons Device Load [ 0.250000] Marvell USB EHCI Host controller #0: c0652600 [ 0.750000] PEX0 interface detected no Link. [ 0.750000] PCI: bus0: Fast back to back transfers enabled [ 0.750000] SCSI subsystem initialized [ 0.750000] usbcore: registered new interface driver usbfs [ 0.750000] usbcore: registered new interface driver hub [ 0.750000] usbcore: registered new device driver usb [ 0.750000] NET: Registered protocol family 2 [ 0.760000] Time: kw_clocksource clocksource has been installed. [ 0.850000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.850000] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.850000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes) [ 0.850000] TCP: Hash tables configured (established 8192 bind 8192) [ 0.850000] TCP reno registered [ 0.880000] RTC has been updated!!! [ 0.880000] RTC registered [ 0.880000] Use the XOR engines (acceleration) for enhancing the following functions: [ 0.880000] o RAID 5 Xor calculation [ 0.880000] o kernel memcpy [ 0.880000] o kenrel memzero [ 0.880000] Number of XOR engines to use: 4 [ 0.880000] cesadev_init(c00117b0) [ 0.880000] mvCesaInit: sessions=640, queue=64, pSram=f0000000 [ 0.880000] MV Buttons Driver Load [ 0.880000] squashfs: version 3.3 (2007/10/31) Phillip Lougher [ 0.880000] squashfs: LZMA suppport for slax.org by jro [ 0.880000] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.880000] io scheduler noop registered [ 0.880000] io scheduler anticipatory registered (default) [ 0.900000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [ 0.900000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A [ 0.910000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize [ 0.920000] Loading Marvell Ethernet Driver: [ 0.920000] o Cached descriptors in DRAM [ 0.920000] o DRAM SW cache-coherency [ 0.930000] o Single RX Queue support - ETH_DEF_RXQ=0 [ 0.930000] o Single TX Queue support - ETH_DEF_TXQ=0 [ 0.940000] o TCP segmentation offload enabled [ 0.940000] o Receive checksum offload enabled [ 0.950000] o Transmit checksum offload enabled [ 0.950000] o Network Fast Processing (Routing) supported [ 0.960000] o Driver ERROR statistics enabled [ 0.960000] o Driver INFO statistics enabled [ 0.970000] o Proc tool API enabled [ 0.970000] o Rx descripors: q0=128 [ 0.970000] o Tx descripors: q0=532 [ 0.980000] o Loading network interface(s): [ 0.990000] o eth0, ifindex = 1, GbE port = 0 [ 0.990000] o eth1, ifindex = 2, GbE port = 1 [ 1.000000] [ 1.000000] mvFpRuleDb (cfdf6000): 2048 entries, 8192 bytes [ 1.000000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI [ 1.010000] Copyright (c) 1999-2006 Intel Corporation. [ 1.020000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI [ 1.020000] e100: Copyright(c) 1999-2006 Intel Corporation [ 1.030000] [ 1.030000] Warning Sata is Powered Off [ 1.030000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ [ 1.040000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit) [ 1.050000] Scanning device for bad blocks [ 1.100000] Using static partition definition [ 1.110000] Creating 4 MTD partitions on "nand_mtd": [ 1.110000] 0x00000000-0x00100000 : "u-boot" [ 1.120000] 0x00100000-0x00500000 : "uImage" [ 1.120000] 0x00500000-0x02500000 : "root" [ 1.130000] 0x02500000-0x08000000 : "data" [ 1.130000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI [ 1.140000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 [ 1.180000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 [ 1.200000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 1.200000] usb usb1: configuration #1 chosen from 1 choice [ 1.210000] hub 1-0:1.0: USB hub found [ 1.210000] hub 1-0:1.0: 1 port detected [ 1.330000] USB Universal Host Controller Interface driver v3.0 [ 1.610000] usb 1-1: new high speed USB device using ehci_marvell and address 2 [ 1.760000] usb 1-1: configuration #1 chosen from 1 choice [ 1.760000] hub 1-1:1.0: USB hub found [ 1.770000] hub 1-1:1.0: 4 ports detected [ 1.880000] usbcore: registered new interface driver usblp [ 1.880000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver [ 1.890000] Initializing USB Mass Storage driver... [ 1.890000] usbcore: registered new interface driver usb-storage [ 1.900000] USB Mass Storage support registered. [ 1.910000] mice: PS/2 mouse device common for all mice [ 1.910000] i2c /dev entries driver [ 1.910000] Linux telephony interface: v1.00 [ 1.920000] md: linear personality registered for level -1 [ 1.920000] md: raid0 personality registered for level 0 [ 1.930000] md: raid1 personality registered for level 1 [ 2.100000] raid6: int32x1 97 MB/s [ 2.270000] raid6: int32x2 114 MB/s [ 2.440000] raid6: int32x4 122 MB/s [ 2.610000] raid6: int32x8 110 MB/s [ 2.610000] raid6: using algorithm int32x4 (122 MB/s) [ 2.610000] md: raid6 personality registered for level 6 [ 2.620000] md: raid5 personality registered for level 5 [ 2.620000] md: raid4 personality registered for level 4 [ 2.630000] raid5: measuring checksumming speed [ 2.680000] arm4regs : 1084.000 MB/sec [ 2.730000] 8regs : 754.800 MB/sec [ 2.780000] 32regs : 899.600 MB/sec [ 2.780000] raid5: using function: arm4regs (1084.000 MB/sec) [ 2.790000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com [ 2.790000] dm_crypt using the OCF package. [ 2.800000] sdhci: Secure Digital Host Controller Interface driver [ 2.800000] sdhci: Copyright(c) Pierre Ossman [ 2.810000] usbcore: registered new interface driver usbhid [ 2.810000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 2.820000] TCP cubic registered [ 2.820000] NET: Registered protocol family 1 [ 2.830000] NET: Registered protocol family 17 [ 2.830000] md: Autodetecting RAID arrays. [ 2.840000] md: autorun ... [ 2.840000] md: ... autorun DONE. [ 3.980000] Empty flash at 0x009ac208 ends at 0x009ac800 [ 6.300000] jffs2_scan_dirent_node(): Node CRC failed on node at 0x012ddff0: Read 0xffffffff, calculated 0xc5be2d45 [ 6.310000] Empty flash at 0x012de024 ends at 0x012de800 [ 9.210000] VFS: Mounted root (jffs2 filesystem) readonly. [ 9.220000] Freeing init memory: 124K init started: BusyBox v1.7.0 (2008-02-26 19:25:17 IST) starting pid 267, tty '': '/etc/init.d/rcS' [ 11.450000] eth0: link down [ 11.450000] eth0: started udhcpc (v1.7.0) started HWADDR 00 0x25 0x31 0x04 0x7b 0x64 PIP0 123 PIP1 100 cat: can't open '/etc/resolv.conf': No such file or directory route: SIOCDELRT: No such process grep: /etc/resolv.conf: No such file or directory Sending discover... [ 13.770000] eth0: link up, full duplex, speed 1 Gbps Sending discover... Sending select for 192.168.86.109... Lease of 192.168.86.109 obtained, lease time 86400 HWADDR 00 0x25 0x31 0x04 0x7b 0x64 PIP0 123 PIP1 100 route: SIOCDELRT: No such process starting pid 378, tty '': '/bin/sh' -sh-4.3#
reboot
The system is going down NOW! Sending SIGTERM to all processes logout Sending SIGKILL to all processes Requesting system reboot [ 170.240000] md: stopping all md devices. [ 171.240000] Restarting system. [ 171.240000] Reseting !! U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:23:43 -0700) Pogo E02 SoC: Kirkwood 88F6281_A0 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Unknown command 'ide' - try 'help' Unknown command 'mmc' - try 'help' no USB devices available Unknown command 'ide' - try 'help' Unknown command 'mmc' - try 'help' running scan_disk ... Scan device usb device usb 0:1 ** Bad device usb 0 ** device usb 1:1 ** Bad device usb 1 ** device usb 2:1 ** Bad device usb 2 ** device usb 3:1 ** Bad device usb 3 ** Scan device ide Unknown command 'ide' - try 'help' device ide 0:1 ** Bad device ide 0 ** device ide 1:1 ** Bad device ide 1 ** device ide 2:1 ** Bad device ide 2 ** device ide 3:1 ** Bad device ide 3 ** Scan device mmc Unknown command 'mmc' - try 'help' device mmc 0:1 ** Bad device mmc 0 ** device mmc 1:1 ** Bad device mmc 1 ** device mmc 2:1 ** Bad device mmc 2 ** device mmc 3:1 ** Bad device mmc 3 ** loading uImage ... ** Bad device usb 0 ** loading uInitrd ... ** Bad device usb 0 ** loading DTB /boot/dts/kirkwood-pogo_e02.dtb ... ** Bad device usb 0 ** ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-2.6.22.18 Created: 2010-10-19 23:05:02 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1979140 Bytes = 1.9 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... Uncompressing Linux............................................................................................................................ done, booting the kernel.
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 29, 2016 04:53AM |
Admin Registered: 13 years ago Posts: 18,575 |
setenv bootcmd 'run bootcmd_uenv; run scan_disk; run set_bootargs; if run bootcmd_exec; then echo Booting with $bootdev ... ; else run pogo_bootcmd; fi; reset boot
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 29, 2016 05:48AM |
Registered: 7 years ago Posts: 310 |
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 30, 2016 03:57PM |
Registered: 7 years ago Posts: 310 |
CE>> reset U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: REDSTONE:0.1 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x100000, size 0x200000 Reading data from 0x2ff800 -- 100% complete. 2097152 bytes read: OK ## Booting image at 00800000 ... Image Name: Linux-3.3.2-kirkwide Created: 2012-10-29 22:52:12 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3627768 Bytes = 3.5 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... Bad Data CRC CE>> I think I am finished with trying to get the device to boot without the usb and hope I can just get it to work again with the usb.
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 30, 2016 04:14PM |
Admin Registered: 13 years ago Posts: 18,575 |
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 30, 2016 04:16PM |
Admin Registered: 13 years ago Posts: 18,575 |
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 30, 2016 04:22PM |
Registered: 7 years ago Posts: 310 |
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 30, 2016 04:30PM |
Admin Registered: 13 years ago Posts: 18,575 |
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 30, 2016 04:36PM |
Registered: 7 years ago Posts: 310 |
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 30, 2016 05:22PM |
Admin Registered: 13 years ago Posts: 18,575 |
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 30, 2016 05:42PM |
Admin Registered: 13 years ago Posts: 18,575 |
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 30, 2016 05:42PM |
Registered: 7 years ago Posts: 310 |
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 30, 2016 06:09PM |
Registered: 7 years ago Posts: 310 |
Quote
Bodhi
Try this: reboot, interrupt serial console and
setenv bootcmd 'run bootcmd_uenv; run scan_disk; run set_bootargs; if run bootcmd_exec; then echo Booting with $bootdev ... ; else run pogo_bootcmd; fi; reset
boot
If this works, try booting back to USB rootfs for sanity, and then repeat this at least once before saveenv again (to commit this new bootcmd for real).
Quote
flash_eraseall /dev/mtd1
nandwrite /dev/mtd1 uImage-mtd1.img
flash_eraseall /dev/mtd2
ubiformat /dev/mtd2 -s 512 -f rootfs-mtd2.img -y
nanddump --noecc --omitoob -l 0x80000 -f mtd0 /dev/mtd0
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 30, 2016 06:32PM |
Admin Registered: 13 years ago Posts: 18,575 |
printenv usb start
ext2ls usb 0:1 /
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 30, 2016 06:40PM |
Registered: 7 years ago Posts: 310 |
U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: REDSTONE:0.1 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 CE>> c Unknown command 'c' - try 'help' CE>> c Unknown command 'c' - try 'help' CE>> <INTERRUPT> CE>> CE>> <INTERRUPT> CE>> CE>> <INTERRUPT> CE>> CE>> <INTERRUPT> CE>> ? ? - alias for 'help' base - print or set address offset boot - boot default, i.e., run 'bootcmd' bootd - boot default, i.e., run 'bootcmd' bootext2 dev:boot_part1,boot_part2 addr boot_image linux_dev_name bootm - boot application image from memory bootp - boot image via network using BootP/TFTP protocol bubt - Burn an image on the Boot Nand Flash. chpart - change active partition cmp - memory compare cmpm - Compare Memory cp - memory copy cpumap - Display CPU memory mapping settings. crc32 - checksum calculation date - get/set/reset date & time dclk - Display the MV device CLKs. dhcp - invoke DHCP client to obtain IP/boot params diskboot- boot from IDE device echo - echo args to console eeprom - EEPROM sub-system erase - erase FLASH memory ext2load- load binary file from a Ext2 filesystem ext2ls - list files in a directory (default /) fi - Find value in the memory. flinfo - print FLASH memory information fsinfo - print information about filesystems fsload - load binary file from a filesystem image g - start application at cached address 'addr'(default addr 0x40000) go - start application at address 'addr' help - print online help icrc32 - checksum calculation ide - IDE sub-system iloop - infinite loop on address range imd - i2c memory display imm[.b, .s, .w, .l] - i2c memory modify (auto-incrementing) imw - memory write (fill) inm - memory modify (constant address) iprobe - probe to discover valid I2C chip addresses ir - reading and changing MV internal register values. loop - infinite loop on address range ls - list files in a directory (default /) map - Diasplay address decode windows md - memory display me - PCI master enable mm - memory modify (auto-incrementing) mp - map PCI BAR mtdparts- define flash/nand partitions mtest - simple RAM test mv_diag - perform board diagnostics mw - memory write (fill) nand - NAND sub-system nboot - boot from NAND device nbubt - Burn a boot loader image on the Boot Nand Flash. nm - memory modify (constant address) pci - list and access PCI Configuration Space phyRead - Read PCI-E Phy register pciePhyWrite - Write PCI-E Phy register phyRead - Read Phy register phyWrite - Write Phy register ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables protect - enable or disable FLASH write protection rarpboot- boot image via network using RARP/TFTP protocol reset - Perform RESET of the CPU resetenv - Return all environment variable to default. run - run commands in an environment variable saveenv - save environment variables to persistent storage se - PCI Slave enable setenv - set environment variables sflash - read, write or erase the external SPI Flash. sg - scanning the PHYs status sp - Scan PCI bus. tftpboot- boot image via network using TFTP protocol version - print monitor version CE>> printenv baudrate=115200 loads_echo=0 rootpath=/mnt/ARM_FS/ run_diag=yes console=console=ttyS0,115200 CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_root=root=/dev/mtdblock2 ro bootcmd=nand read.e 0x800000 0x100000 0x200000; setenv bootargs $(console) $(bootargs_root); bootm 0x800000 ceboardver=REDSTONE:0.1 ethmtu=1500 usb0Mode=host nandEcc=1bit ethact=egiga0 filesize=80000 fileaddr=800000 netmask=255.255.0.0 ipaddr=192.168.86.109 serverip=192.168.86.110 ethaddr=00:25:31:04:7B:64 bootargs=console=ttyS0,115200 root=/dev/mtdblock2 ro stdin=serial stdout=serial stderr=serial mainlineLinux=yes arcNumber=9 enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no Environment size: 802/131068 bytes CE>>
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 30, 2016 06:53PM |
Admin Registered: 13 years ago Posts: 18,575 |
setenv ipaddr 192.168.0.xxx setenv serverip 192.168.0.yyy setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=10' tftpboot 0x800000 uImage tftpboot 0x1100000 uInitrd bootm 0x800000 0x1100000
Re: Broke my E02 updating "2016.05 U-Boot Kirkwood - PogoE02" July 30, 2016 07:53PM |
Registered: 7 years ago Posts: 310 |