Help with Pogoplug E02 Restore / Repair - Have Serial Access

I picked up a Pogoplug a while back and had messed with it a little before putting it on the shelf.

Plugged it back in recently to try and use it for a little home server and proceeded to bork it up something fierce while trying to install Arch. It's very possible I tried to install Debian on this thing previously so maybe that's the root of the problems?

Regardless- I'd like a method to restore the E02 back to the original factory firmware so I can start the process all over again. I don't have any backups of the original image.

Here's what I get on the serial console:

U-Boot 2014.07-tld-2 (Sep 20 2014 - 00:52:18)
Pogo E02

SoC:   Kirkwood 88F6281_A0
DRAM:  256 MiB
WARNING: Caches not enabled
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
No link on egiga0
ping failed; host 192.168.1.1 is not alive
Hit any key to stop autoboot:  0
Unknown command 'usb' - try 'help'
Unknown command 'mmc' - try 'help'
Unknown command 'ide' - try 'help'
USB is stopped. Please issue 'usb start' first.
Unknown command 'mmc' - try 'help'
Unknown command 'ide' - try 'help'
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
** Bad device usb 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Unknown command 'mmc' - try 'help'
Unknown command 'bootargs' - try 'help'
** Bad device mmc 0 **
** Bad device mmc 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Unknown command 'ide' - try 'help'
** Bad device ide 0 **
** Bad device ide 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
resetting ...

Any help would be appreciated!

mrmees Wrote:
-------------------------------------------------------
> I picked up a Pogoplug a while back and had messed
> with it a little before putting it on the shelf.
>
> Plugged it back in recently to try and use it for
> a little home server and proceeded to bork it up
> something fierce while trying to install Arch.
> It's very possible I tried to install Debian on
> this thing previously so maybe that's the root of
> the problems?
>
> Regardless- I'd like a method to restore the E02
> back to the original factory firmware so I can
> start the process all over again. I don't have any
> backups of the original image.
>
> Here's what I get on the serial console:
>
>

> U-Boot 2014.07-tld-2 (Sep 20 2014 - 00:52:18)
> Pogo E02
> 
> SoC:   Kirkwood 88F6281_A0
> DRAM:  256 MiB
> WARNING: Caches not enabled
> NAND:  128 MiB
> In:    serial
> Out:   serial
> Err:   serial
> Net:   egiga0
> No link on egiga0
> ping failed; host 192.168.1.1 is not alive
> Hit any key to stop autoboot:  0
> Unknown command 'usb' - try 'help'
> Unknown command 'mmc' - try 'help'
> Unknown command 'ide' - try 'help'
> USB is stopped. Please issue 'usb start' first.
> Unknown command 'mmc' - try 'help'
> Unknown command 'ide' - try 'help'
> (Re)start USB...
> USB0:   USB EHCI 1.00
> scanning bus 0 for devices... 2 USB Device(s)
> found
>        scanning usb for storage devices... 0
> Storage Device(s) found
> ** Bad device usb 0 **
> ** Bad device usb 0 **
> Wrong Image Format for bootm command
> ERROR: can't get kernel image!
> Unknown command 'mmc' - try 'help'
> Unknown command 'bootargs' - try 'help'
> ** Bad device mmc 0 **
> ** Bad device mmc 0 **
> Wrong Image Format for bootm command
> ERROR: can't get kernel image!
> Unknown command 'ide' - try 'help'
> ** Bad device ide 0 **
> ** Bad device ide 0 **
> Wrong Image Format for bootm command
> ERROR: can't get kernel image!
> resetting ...
>

>
> Any help would be appreciated!


Interrupt serial console and

printenv

Pls post the listing.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)