|
Help on getting u-boot replacement on stock Buffalo LS-WVL September 05, 2016 12:58AM |
Registered: 11 years ago Posts: 32 |
|
Re: Help on getting u-boot replacement on stock Buffalo LS-WVL September 05, 2016 01:23AM |
Admin Registered: 13 years ago Posts: 18,545 |
Quote
Last Updated 19 June 2016
I've uploaded 2016.05-tld-1 U-Boot images for Pogo E02, GoFlexNet, GoFlex Home, Dockstar, Pogo V4/Mobile, iConnect, Netgear Stora, Sheevaplug, NSA320, NSA325, NSA310S/320S, NSA310, and HP-T5325.
Important Note: If possible, try to test this boot image with UART booting before flashing to NAND. See davygravy's UART booting using kwboot instruction here in this thread. The latest u-boot image released here should be used for UART booting, if your box is the type that supports it (these do not: Dockstar, Pogo E02, iConnect).
To download ARM kwboot binary for UART booting at Dropbox:
kwboot
md5:
0efd011bdb244436e432a8de33e639a1
Quote
uboot.2016.05-tld-1.nsa325.bodhi.tar
md5:
a1a72c8750a0e5c3993c4f1ef1e71d0e
sha256:
33259fd66a9ebfad9b13359002753844cebe9e976ecd5f719faf71a75fd82cdd
|
Re: Help on getting u-boot replacement on stock Buffalo LS-WVL September 05, 2016 03:13AM |
Admin Registered: 13 years ago Posts: 18,545 |
|
Re: Help on getting u-boot replacement on stock Buffalo LS-WVL September 12, 2016 05:22AM |
Registered: 11 years ago Posts: 32 |
|
Re: Help on getting u-boot replacement on stock Buffalo LS-WVL September 12, 2016 07:47AM |
Registered: 11 years ago Posts: 32 |
|
Re: Help on getting u-boot replacement on stock Buffalo LS-WVL September 12, 2016 10:52AM |
Registered: 11 years ago Posts: 32 |
** LOADER **t ** BUFFALO BOARD: MVLSWV LE ** Board ID: 0x82 U-Boot 1.1.4 (Jul 6 2011 - 20:16:40) Marvell version: 3.5.3 U-Boot code: 00600000 -> 0066FFF0 BSS: -> 006BF4C0 BUFFALO_BOOTVER=0.26 Soc: 88F6282 A0CPU running @ 1600Mhz L2 running @ 533Mhz SysClock = 533Mhz , TClock = 200Mhz DRAM (DDR3) CAS Latency = 7 tRP = 8 tRAS = 20 tRCD=8 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:512 MB [512kB@f8000000] Flash: 512 kB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode MacicKey = 0x00 buffalo_IsStopAtUbootStatus > MagicKey = 0x00 bfSetMagicKey > Changed to 0x5c from 0x00 HDD0 Power ON HDD1 Power ON Marvell Serial ATA Adapter Integrated Sata device found HDD is not found Resetting EthPhy Net: egiga0 hit any key to switch tftp boot. Hit any key to stop autoboot: 0 Hit any key to stop autoboot: 0 ** Bad partition 1 ** ** Bad partition 1 ** ## Booting image at 00100000 ... Bad Magic Number ### JFFS2 loading '/uImage.buffalo' to 0x100000 Scanning JFFS2 FS: . done. ### JFFS2 load complete: 2726608 bytes loaded to 0x100000 ### JFFS2 loading '/initrd.buffalo' to 0x800000 ### JFFS2 load complete: 9614969 bytes loaded to 0x800000 ## Booting image at 00100000 ... Image Name: Linux-2.6.31.8-svn22059 Created: 2010-09-13 0:43:03 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2726544 Bytes = 2.6 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 00800000 ... Image Name: initrd Created: 2012-03-13 4:11:46 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9614905 Bytes = 9.2 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux......................................................................................................................................................................... done, booting the kernel. Linux version 2.6.31.8-svn22059 (root@build2.dd-hot24.nas.buffalo.local) (gcc version 4.2.0 20070413 (prerelease)) #67 Mon Sep 13 09:42:55 JST 2010 CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977 CPU: VIVT data cache, VIVT instruction cache Machine: Feroceon-KW Using UBoot passing parameters structure Memory policy: ECC disabled, Data cache writeback Built 1 zonelists in Zone order, mobility grouping off. Total pages: 65024 Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,12M panic=5 BOOTVER=0.26 mtdparts=nand_mtd:0x1000000(boot),0x1e800000(rootfs),0x800000(reserve) nandboot=yes PID hash table entries: 1024 (order: 10, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 256MB = 256MB total Memory: 235776KB available (4964K code, 269K data, 152K init, 0K highmem) Hierarchical RCU implementation. NR_IRQS:128 Console: colour dummy device 80x30 Calibrating delay loop... 1599.07 BogoMIPS (lpj=7995392) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok xor: measuring software checksum speed arm4regs : 1453.600 MB/sec 8regs : 1102.400 MB/sec 32regs : 1236.400 MB/sec xor: using function: arm4regs (1453.600 MB/sec) NET: Registered protocol family 16 Feroceon L2: Enabling L2 Feroceon L2: Cache support initialised. CPU Interface ------------- SDRAM_CS0 ....base 00000000, size 256MB SDRAM_CS1 ....disable SDRAM_CS2 ....disable SDRAM_CS3 ....disable PEX0_MEM ....base e0000000, size 128MB PEX0_IO ....base f2000000, size 1MB PEX1_MEM ....base e8000000, size 128MB PEX1_IO ....base f2100000, size 1MB INTER_REGS ....base f1000000, size 1MB NFLASH_CS ....base fa000000, size 2MB SPI_CS ....base f4000000, size 16MB BOOT_ROM_CS ....no such DEV_BOOTCS ....no such CRYPT_ENG ....base f0000000, size 2MB Marvell Development Board (LSP Version KW_LSP_5.1.3)-- MVLSWV Soc: 88F6282 A0 LE Detected Tclk 200000000 and SysClk 533333333 MV Buttons Device Load Marvell USB EHCI Host controller #0: c8040800 PEX0 interface detected no Link. PEX1 interface detected no Link. PCI: bus0: Fast back to back transfers enabled PCI: bus1: Fast back to back transfers enabled bio: create slab <bio-0> at 0 SCSI subsystem initialized raid6: int32x1 149 MB/s raid6: int32x2 175 MB/s raid6: int32x4 171 MB/s raid6: int32x8 156 MB/s raid6: using algorithm int32x2 (175 MB/s) NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered NET: Registered protocol family 1 Trying to unpack rootfs image as initramfs... rootfs image is not initramfs (no cpio magic); looks like an initrd Freeing initrd memory: 12288K rtc mv_rtc: rtc core: registered kw-rtc as rtc0 RTC registered MICON ctrl (C) BUFFALO INC. V.1.00 installed. Buffalo Gpio Control Driver (C) BUFFALO INC. Ver.1.00 installed. Buffalo CPU Inerupts Driver (C) BUFFALO INC. Ver.0.01 alpha1 installed. Kernel event proc (C) BUFFALO INC. V.1.00 installed. initial_polarity_val = 0x00030000 initial_polarity_val_high = 0x0001f100 Buffalo GPIO SATA Hotplug Event Driver (C) BUFFALO INC. Ver.1.00 installed. XOR registered 4 channels XOR 2nd invalidate WA enabled cesadev_init(c000fd64) MV Buttons Driver Load VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Installing knfsd (copyright (C) 1996 okir@monad.swb.de). JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. fuse init (API version 7.12) SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled SGI XFS Quota Management subsystem msgmni has been set to 485 alg: No test for cipher_null (cipher_null-generic) alg: No test for ecb(cipher_null) (ecb-cipher_null) alg: No test for digest_null (digest_null-generic) alg: No test for compress_null (compress_null-generic) alg: No test for stdrng (krng) alg: No test for hmac(digest_null) (hmac(digest_null-generic)) async_tx: api initialized (sync-only) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) io scheduler noop registered io scheduler anticipatory registered (default) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A console [ttyS0] enabled serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A brd: module loaded loop: module loaded Integrated Sata device found mvSataInitAdapter : regVal changed(0x00000010) IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs scsi0 : Marvell SCSI to SATA adapter scsi1 : Marvell SCSI to SATA adapter Loading Marvell Ethernet Driver: o Cached descriptors in DRAM o DRAM SW cache-coherency o 2 Giga ports supported o Single RX Queue support - ETH_DEF_RXQ=0 o Single TX Queue suBad eraseblock 1287 at 0x00000a0e0000 Bad eraseblock 3718 at 0x00001d0c0000 3 cmdlinepart partitions found on MTD device nand_mtd Using command line partition definition Creating 3 MTD partitions on "nand_mtd": 0x000000000000-0x000001000000 : "boot" 0x000001000000-0x00001f800000 : "rootfs" 0x00001f800000-0x000020000000 : "reserve" mice: PS/2 mouse device common for all mice Linux telephony interface: v1.00 md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com TCP cubic registered NET: Registered protocol family 17 NET: Registered protocol family 15 RPC: Registered udp transport module. RPC: Registered tcp transport module. rtc mv_rtc: setting system clock to 2012-08-11 04:21:40 UTC (1344658900) md: Waiting for all devices to be available before autodetect md: If you don't use raid, use raid=noautodetect md: Autodetecting RAID arrays. md: Scanned 0 and added 0 devices. md: autorun ... md: ... autorun DONE. RAMDISK: gzip image found at block 0 VFS: Mounted root (ext2 filesystem) on device 1:0. ---- in linuxrc --- Version 1.00 2008/ 7/ 1 modprobe: FATAL: Could not load /lib/modules/2.6.31.8-svn22059/modules.dep: No such file or directory hwclock: can't open '/dev/misc/rtc': No such file or directory Sat Aug 11 13:21:41 JST 2012 WARNING: Couldn't open directory /lib/modules/2.6.31.8-svn22059: No such file or directory FATAL: Could not open /lib/modules/2.6.31.8-svn22059/modules.dep.temp for writing: No such file or directory ls: sd*: No such file or directory ls: sd*: No such file or directory linuxrc:choose operation (timeout 4[s]) 1:RamRoot other:HddRoot ? -HddRoot- /var/tmp/devlink: line 2: sd*=/dev/disk1: No such file or directory -- rebuild mdadm.conf for BOOT, ROOTFS -- mdadm: cannot open /dev/disk?_1: No such file or directory mdadm: cannot open /dev/disk?_2: No such file or directory mdadm: cannot open /dev/disk?_5: No such file or directory mdadm: No devices listed in conf file were found. -- setup max error counts -- /sys/block/md0/md/maxerr_cnt is setted to -1 Starting :fscEXT3-fs: unable to read superblock k_disks(boot) ..EXT2-fs: unable to read superblock . [Failed. ] Starting :mount(boot) ... EXT3-fs: unable to read superblock EXT2-fs: unable to read superblock [Failed. ] /var/tmp/devlink: line 2: sd*=/dev/disk1: No such file or directory -- rebuild mdadm.conf for BOOT, ROOTFS -- mdadm: cannot open /dev/disk?_1: No such file or directory mdadm: cannot open /dev/disk?_2: No such file or directory mdadm: cEXT3-fs: unable to read superblock annot open /dev/EXT2-fs: unable to read superblock disk?_5: No such file or directory mdadm: No devices listed in EXT3-fs: unable to read superblock conf file were fEXT2-fs: unable to read superblock ound. -- setup max error counts -- /sys/block/md0/md/maxerr_cnt is setted to -1 /sys/block/md1/md/maxerr_cnt is setted to -1 /usr/local/lib/libmd.sh: line 574: /sys/block/md1/md/maxerr_cnt: No such file or directory /sys/block/md10/md/maxerr_cnt is setted to -1 /usr/local/lib/libmd.sh: line 574: /sys/block/md10/md/maxerr_cnt: No such file or directory mount: mounting /dev/md1 on /mnt failed: Input/output error mount: mounting /dev/md1 on /mnt failed: Input/output error /var/tmp/devlink: line 2: sd*=/dev/disk1: No such file or directory md: md0 stopped. mdadm: stopped /md: md1 stopped. dev/md0 mdadm: stopped /md: md10 stopped. dev/md1 mdadm: stopped /dev/md10 umount: cannot open /proc/mounts Freeing init memory: 152K init started: BusyBox v1.7.0 (2009-04-29 19:12:57 JST) starting pid 589, tty '': '/etc/init.d/rcS' --- rcStart (initrd) --- * Starting :udev.sh ... [Success.] * Starting :checkroot.sh ... [Success.] * Starting :create_devlink.sh ... [Success.] * Starting :startSysMd.sh ... [Success.] * Starting :errormon.sh ... [Success.] * Starting :fwupdate.sh ... [Success.] * Starting :check_nandboot.sh ... [Success.] grep: /tmp/check_nandboot: No such file or directory * Starting :closeSysMd.sh ... [Failed. ] * Starting :sethostname.sh ... [Success.] * Starting :restore_config.sh ... [Success.] * Starting :EnablingAutoip.sh ... [Success.] * Starting :networking.sh ... eth0: started ** eth0 : networking.sh dhcp fin. [Success.] * Starting :syslog.sh ... [Success.] * Starting :kernelmon.sh ... [Success.] * Starting :usb.sh ... [Failed. ] * Starting :clientUtil_servd.sh ... [Success.] * Starting :daemonwatch.sh ... [Success.] * Starting :bootcomplete.sh ... bfSetMagicKey > Changed to 0x71 from 0x5c [Success.] * Starting :late_inspection_phase.sh ... [Success.] starting pid 1474, tty '': '/sbin/getty' BUFFALO INC. LinkStation series LS-WVL-EMBA3 login: KERNELMOn (PSW_on) BUFFALO INC. LinkStation series LS-WVL-EMBA3 login:
|
Re: Help on getting u-boot replacement on stock Buffalo LS-WVL September 12, 2016 01:08PM |
Admin Registered: 13 years ago Posts: 18,545 |
usb start ide resetand
ping <your router IP address>
|
Re: Help on getting u-boot replacement on stock Buffalo LS-WVL September 12, 2016 02:21PM |
Registered: 11 years ago Posts: 32 |
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: egiga0
PHY reset timed out
MV88E1318 PHY initialized on egiga0
Hit any key to stop autoboot: 10 9 0
NSA325> usb start
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
NSA325> ide reset
Reset IDE: ide_preinit failed
NSA325> setenv ipaddr 192.168.1.191
NSA325> ping 192.168.1.1
Using egiga0 device
host 192.168.1.1 is alive
NSA325>
|
Re: Help on getting u-boot replacement on stock Buffalo LS-WVL September 13, 2016 12:52AM |
Admin Registered: 13 years ago Posts: 18,545 |
|
Re: Help on getting u-boot replacement on stock Buffalo LS-WVL September 13, 2016 10:22AM |
Registered: 11 years ago Posts: 32 |
|
Re: Help on getting u-boot replacement on stock Buffalo LS-WVL September 13, 2016 10:53AM |
Registered: 11 years ago Posts: 32 |
/****************************** MVLSWV ******************************/
MV_BOARD_MAC_INFO mvlswvInfoBoardMacInfo[] =
/* {{MV_BOARD_MAC_SPEED boardMacSpeed, MV_U8 boardEthSmiAddr}} */
{
{BOARD_MAC_SPEED_AUTO, 0x0}
};
MV_BOARD_GPP_INFO mvlswvInfoBoardGppInfo[] =
/* {{MV_BOARD_GPP_CLASS devClass, MV_U8 gppPinNum}} */
{
{BOARD_GPP_HDD_POWER, 8},
{BOARD_GPP_HDD_POWER, 9},
{BOARD_GPP_USB_VBUS_EN, 12},
{BOARD_GPP_FAN_LOW, 16},
{BOARD_GPP_FAN_HIGH, 17},
{BOARD_GPP_FUNC_LED, 39},
{BOARD_GPP_ALARM_LED, 36},
{BOARD_GPP_INFO_LED, 38},
{BOARD_GPP_PWR_LED, 40},
{BOARD_GPP_FAN_LOCK, 43},
{BOARD_GPP_FUNC_SW, 45},
{BOARD_GPP_PWR_SW, 46},
{BOARD_GPP_PWRAUTO_SW, 47},
{BOARD_GPP_FUNC_RED_LED, 37},
{BOARD_GPP_UART_EN, 48},
};
MV_BOARD_MPP_TYPE_INFO mvlswvInfoBoardMppTypeInfo[] =
/* {{MV_BOARD_MPP_TYPE_CLASS boardMppGroup1,
MV_BOARD_MPP_TYPE_CLASS boardMppGroup2}} */
{
{MV_BOARD_OTHER, MV_BOARD_OTHER}
//{MV_BOARD_OTHER,MV_BOARD_RGMII}
};
MV_BOARD_MPP_INFO mvlswvInfoBoardMppConfigValue[] =
{{{
MVLSWV_MPP0_7,
MVLSWV_MPP8_15,
MVLSWV_MPP16_23,
MVLSWV_MPP24_31,
MVLSWV_MPP32_39,
MVLSWV_MPP40_47,
MVLSWV_MPP48_55
}}};
MV_DEV_CS_INFO mvlswvInfoBoardDeCsInfo[] =
/*{deviceCS, params, devType, devWidth}*/
{
{0, N_A, BOARD_DEV_NAND_FLASH, 8}, /* NAND DEV */
{1, N_A, BOARD_DEV_SPI_FLASH, 8} /* SPI DEV */
};
#define MVLSWV_BOARD_PCI_IF_NUM 0x0
#define MVLSWV_BOARD_TWSI_DEF_NUM 0x0
#define MVLSWV_BOARD_MAC_INFO_NUM 0x1
#define MVLSWV_BOARD_GPP_INFO_NUM (sizeof(mvlswvInfoBoardGppInfo)/sizeof(MV_BOARD_GPP_INFO))
#define MVLSWV_BOARD_MPP_GROUP_TYPE_NUM 0x0
#define MVLSWV_BOARD_MPP_CONFIG_NUM 0x1
#define MVLSWV_BOARD_DEVICE_CONFIG_NUM 0x2
#define MVLSWV_BOARD_NAND_READ_PARAMS 0x003E07CF
#define MVLSWV_BOARD_NAND_WRITE_PARAMS 0x000F0F0F
#define MVLSWV_BOARD_NAND_CONTROL 0x01c7D943
MV_BOARD_INFO mvlswvInfo = {
"MVLSWV", /* boardName[MAX_BOARD_NAME_LEN] */
MVLSWV_BOARD_MPP_GROUP_TYPE_NUM, /* numBoardMppTypeValue */
mvlswvInfoBoardMppTypeInfo, /* pBoardMppTypeValue */
MVLSWV_BOARD_MPP_CONFIG_NUM, /* numBoardMppConfigValue */
mvlswvInfoBoardMppConfigValue, /* pBoardMppConfigValue */
0, /* intsGppMaskLow */
0, /* intsGppMaskHigh */
MVLSWV_BOARD_DEVICE_CONFIG_NUM, /* numBoardDeviceIf */
mvlsxhInfoBoardDeCsInfo, /* pDevCsInfo */
MVLSWV_BOARD_TWSI_DEF_NUM, /* numBoardTwsiDev */
NULL, /* pBoardTwsiDev */
MVLSWV_BOARD_MAC_INFO_NUM, /* numBoardMacInfo */
mvlswvInfoBoardMacInfo, /* pBoardMacInfo */
MVLSWV_BOARD_GPP_INFO_NUM, /* numBoardGppInfo */
mvlswvInfoBoardGppInfo, /* pBoardGppInfo */
0, /* activeLedsNumber */
NULL, /* pLedGppPin */
0, /* ledsPolarity */
MVLSWV_OE_LOW, /* gppOutEnLow */
MVLSWV_OE_HIGH, /* gppOutEnHigh */
MVLSWV_OE_VAL_LOW, /* gppOutValLow */
MVLSWV_OE_VAL_HIGH, /* gppOutValHigh */
MVLSWV_POLARITY_VAL_LOW, /* gppPolarityValLow */
MVLSWV_POLARITY_VAL_HIGH, /* gppPolarityValHigh */
NULL, /* pSwitchInfo */
MVLSWV_BOARD_NAND_READ_PARAMS, /* nandFlashReadParams */
MVLSWV_BOARD_NAND_WRITE_PARAMS, /* nandFlashWriteParams */
MVLSWV_BOARD_NAND_CONTROL, /* nandFlashControl */
};
|
Re: Help on getting u-boot replacement on stock Buffalo LS-WVL January 24, 2017 10:48AM |
Registered: 11 years ago Posts: 32 |
|
Re: Help on getting u-boot replacement on stock Buffalo LS-WVL October 15, 2019 02:26PM |
Registered: 12 years ago Posts: 1 |
|
Re: Help on getting u-boot replacement on stock Buffalo LS-WVL October 15, 2019 03:41PM |
Registered: 5 years ago Posts: 252 |