Welcome! Log In Create A New Profile

Advanced

Recovery via Serial: Not working as I don't get an IP

Posted by Hendrik 
Forum List Message List New Topic
Hendrik
Recovery via Serial: Not working as I don't get an IP
December 24, 2010 08:32AM
Hello,

I somehow bricked my dockstar.
But now I have a Serial connection ;-)

Unfortunately, I cannot just re-install, as I don't get an IP-Address, thus, I fail already with wget.

But debian is running.

ifconfig shows no output at all

Now I intended to boot the pogoplug enviroment, but that doesn't work using this command:
blparam bootcmd='run bootcmd_original' 

MTD: /dev/mtd0
     type:          4
     flags:         0x400
     size:          1048576
     erase size:    131072
     write size:    2048
     oob size:      64
  -- Removing parameter 'bootcmd' from 'run bootcmd_original' because 'bootcmd=run bootcmd_original'
  -- Adding parameter 'bootcmd=run bootcmd_original'
  -- Writing parameter 'baudrate=115200'
  -- Writing parameter 'loads_echo=0'
  -- Writing parameter 'serverip=169.254.254.254'
  -- Writing parameter 'rootpath=/mnt/ARM_FS/'
  -- Writing parameter 'netmask=255.255.0.0'
  -- Writing parameter 'run_diag=yes'
  -- Writing parameter 'console=console=ttyS0,115200'
  -- Writing parameter 'CASset=min'
  -- Writing parameter 'MALLOC_len=1'
  -- Writing parameter 'ethprime=egiga0'
  -- Writing parameter 'ethmtu=1500'
  -- Writing parameter 'usb0Mode=host'
  -- Writing parameter 'nandEcc=1bit'
  -- Writing parameter 'ethact=egiga0'
  -- Writing parameter 'stdin=serial'
  -- Writing parameter 'stdout=serial'
  -- Writing parameter 'stderr=serial'
  -- Writing parameter 'mainlineLinux=no'
  -- Writing parameter 'enaMonExt=no'
  -- Writing parameter 'enaCpuStream=no'
  -- Writing parameter 'enaWrAllo=no'
  -- Writing parameter 'pexMode=RC'
  -- Writing parameter 'disL2Cache=no'
  -- Writing parameter 'setL2CacheWT=yes'
  -- Writing parameter 'disL2Prefetch=yes'
  -- Writing parameter 'enaICPref=yes'
  -- Writing parameter 'enaDCPref=yes'
  -- Writing parameter 'sata_dma_mode=yes'
  -- Writing parameter 'netbsd_en=no'
  -- Writing parameter 'vxworks_en=no'
  -- Writing parameter 'bootdelay=3'
  -- Writing parameter 'disaMvPnp=no'
  -- Writing parameter 'ethaddr=00:10:75:1A:CA:99'
  -- Writing parameter 'cesvcid=FH78P92T5QD4CL9M9JLM2DMBDA'
  -- Writing parameter 'ceserialno=2GEP1FLN'
  -- Writing parameter 'ceboardver=REDSTONE:1.0'
  -- Writing parameter 'bootargs_root=root=/dev/mtdblock2 ro'
  -- Writing parameter 'bootcmd_original=nand read.e 0x800000 0x100000 0x300000; setenv bootargs $(console) $(bootargs_root); bootm 0x800000'
  -- Writing parameter 'ipaddr=192.168.178.4'
  -- Writing parameter 'active_host=192.168.178.1'
  -- Writing parameter 'if_connected=ping ${active_host}'
  -- Writing parameter 'bootcmd=run bootcmd_original'
Erasing 128 kb @ 0xa0000
Writing 2048 kb @ 0xbf800
***
*** BOOT LOADER PARAMETERS CHANGED -- REBOOT NECESSARY TO TAKE EFFECT!
***

It always boots the debian, that I installed in the NAND (no USB device connected).

Now, how do I get the pogoplug enviroment to boot?


Below, there's a complete boot log.

How should I go on?

Regards,
Hendrik 


U-Boot 2010.09 (Oct 23 2010 - 11:49:22)
Marvell-Dockstar/Pogoplug by Jeff Doozan

SoC:   Kirkwood 88F6281_A0
DRAM:  128 MiB
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot:  0
(Re)start USB...
USB:   Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported

** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=3"
UBI: MTD device size:            219 MiB
UBI: number of good PEBs:        1752
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     1
UBI: available PEBs:             0
UBI: total number of reserved PEBs: 1752
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 36/8
UBIFS: recovery needed
UBIFS: recovery deferred
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: mounted read-only
UBIFS: file system size:   221921280 bytes (216720 KiB, 211 MiB, 1720 LEBs)
UBIFS: journal size:       11096064 bytes (10836 KiB, 10 MiB, 86 LEBs)
UBIFS: media format:       w4/r0 (latest is w4/r0)
UBIFS: default compressor: LZO
UBIFS: reserved for root:  5182151 bytes (5060 KiB)
Loading file '/boot/uImage' to addr 0x00800000 with size 1430932 (0x0015d594)...
Done
Loading file '/boot/uInitrd' to addr 0x01100000 with size 4850382 (0x004a02ce)...
Done
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-2.6.32-5
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1430868 Bytes = 1.4 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
   Image Name:   initramfs
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    4850318 Bytes = 4.6 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.32-5-kirkwood (Debian 2.6.32-20) (ben@decadent.org.uk) (gcc version 4.3.5 (Debian 4.3.5-2) ) #1 Fri Aug 13 01:53:46 UTC 2010
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: Marvell SheevaPlug Reference Board
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 128MB = 128MB total
[    0.000000] Memory: 120716KB available (3508K code, 582K data, 124K init, 0K highmem)
[    0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:114
[    0.000000] Console: colour dummy device 80x30
[   21.474958] Calibrating delay loop... 1192.75 BogoMIPS (lpj=5963776)
[   21.714914] Security Framework initialized
[   21.714934] SELinux:  Disabled at boot.
[   21.714955] Mount-cache hash table entries: 512
[   21.715204] Initializing cgroup subsys ns
[   21.715217] Initializing cgroup subsys cpuacct
[   21.715226] Initializing cgroup subsys devices
[   21.715235] Initializing cgroup subsys freezer
[   21.715243] Initializing cgroup subsys net_cls
[   21.715275] CPU: Testing write buffer coherency: ok
[   21.715825] devtmpfs: initialized
[   21.717250] regulator: core version 0.5
[   21.717423] NET: Registered protocol family 16
[   21.717807] Kirkwood: MV88F6281-A0, TCLK=200000000.
[   21.717819] Feroceon L2: Cache support initialised.
[   21.719650] bio: create slab <bio-0> at 0
[   21.719925] vgaarb: loaded
[   21.720389] Switching to clocksource orion_clocksource
[   21.724207] NET: Registered protocol family 2
[   21.724453] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[   21.725288] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[   21.725388] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[   21.725440] TCP: Hash tables configured (established 4096 bind 4096)
[   21.725450] TCP reno registered
[   21.725601] NET: Registered protocol family 1
[   21.725778] Unpacking initramfs...
[   22.055257] Freeing initrd memory: 4736K
[   22.055356] NetWinder Floating Point Emulator V0.97 (double precision)
[   22.055618] audit: initializing netlink socket (disabled)
[   22.055653] type=2000 audit(0.570:1): initialized
[   22.062285] VFS: Disk quotas dquot_6.5.2
[   22.062557] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   22.062653] JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[   22.063294] msgmni has been set to 245
[   22.065003] alg: No test for stdrng (krng)
[   22.065128] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[   22.065140] io scheduler noop registered
[   22.065148] io scheduler anticipatory registered
[   22.065155] io scheduler deadline registered
[   22.065344] io scheduler cfq registered (default)
[   22.071401] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[   22.071876] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[   22.395376] console [ttyS0] enabled
[   22.399438] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit)
[   22.408050] Scanning device for bad blocks
[   22.417041] Bad eraseblock 130 at 0x000001040000
[   22.492746] 4 cmdlinepart partitions found on MTD device orion_nand
[   22.499047] Creating 4 MTD partitions on "orion_nand":
[   22.504228] 0x000000000000-0x000000100000 : "u-boot"
[   22.509779] 0x000000100000-0x000000500000 : "uImage"
[   22.515258] 0x000000500000-0x000002500000 : "rootfs"
[   22.520765] 0x000002500000-0x000010000000 : "data"
[   22.526395] UBI: attaching mtd3 to ubi0
[   22.530249] UBI: physical eraseblock size:   131072 bytes (128 KiB)
[   22.536563] UBI: logical eraseblock size:    129024 bytes
[   22.541992] UBI: smallest flash I/O unit:    2048
[   22.546717] UBI: sub-page size:              512
[   22.551366] UBI: VID header offset:          512 (aligned 512)
[   22.557225] UBI: data offset:                2048
[   22.911417] UBI: attached mtd3 to ubi0
[   22.915190] UBI: MTD device name:            "data"
[   22.920090] UBI: MTD device size:            219 MiB
[   22.925103] UBI: number of good PEBs:        1752
[   22.929830] UBI: number of bad PEBs:         0
[   22.934304] UBI: max. allowed volumes:       128
[   22.938942] UBI: wear-leveling threshold:    4096
[   22.943677] UBI: number of internal volumes: 1
[   22.948142] UBI: number of user volumes:     1
[   22.952615] UBI: available PEBs:             0
[   22.957081] UBI: total number of reserved PEBs: 1752
[   22.962077] UBI: number of PEBs reserved for bad PEB handling: 17
[   22.968199] UBI: max/mean erase counter: 36/8
[   22.972583] UBI: image sequence number: 0
[   22.976612] UBI: background thread "ubi_bgt0d" started, PID 26
[   22.982844] mice: PS/2 mouse device common for all mice
[   23.990431] rtc-mv rtc-mv: internal RTC not ticking
[   23.995420] i2c /dev entries driver
[   23.999094] cpuidle: using governor ladder
[   24.003346] cpuidle: using governor menu
[   24.007379] Registered led device: plug:green:health
[   24.012438] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
[   24.018846] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
[   24.060458] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[   24.100454] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
[   24.140453] mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
[   24.180455] mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
[   24.187132] TCP cubic registered
[   24.190378] NET: Registered protocol family 17
[   24.195200] registered taskstats version 1
[   24.199985] /build/buildd-linux-2.6_2.6.32-20-armel-qpwOHl/linux-2.6-2.6.32/debian/build/source_armel_none/drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[   24.214597] Initalizing network drop monitor service
[   24.219644] Freeing init memory: 124K
Loading, please wait...
[   24.270951] udev: starting version 160
[   24.551482] MV-643xx 10/100/1000 ethernet driver version 1.4
[   24.557465] mv643xx_eth smi: probed
[   24.609113] usbcore: registered new interface driver usbfs
[   24.620712] usbcore: registered new interface driver hub
[   24.627493] net eth0: port 0 with MAC address 00:10:75:1a:ca:99
[   24.634146] mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
[   24.646899] usbcore: registered new device driver usb
[   24.666389] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   24.673035] orion-ehci orion-ehci.0: Marvell Orion EHCI
[   24.678340] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[   24.710438] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[   24.730423] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[   24.738075] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[   24.744933] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   24.752200] usb usb1: Product: Marvell Orion EHCI
[   24.756925] usb usb1: Manufacturer: Linux 2.6.32-5-kirkwood ehci_hcd
[   24.763317] usb usb1: SerialNumber: orion-ehci.0
[   24.769776] usb usb1: configuration #1 chosen from 1 choice
[   24.775736] hub 1-0:1.0: USB hub found
[   24.779533] hub 1-0:1.0: 1 port detected
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
[   24.899489] UBIFS: recovery needed
[   24.969198] UBIFS: recovery deferred
[   24.972832] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[   24.978864] UBIFS: mounted read-only
[   24.982462] UBIFS: file system size:   221921280 bytes (216720 KiB, 211 MiB, 1720 LEBs)
[   24.990526] UBIFS: journal size:       11096064 bytes (10836 KiB, 10 MiB, 86 LEBs)
[   24.998129] UBIFS: media format:       w4/r0 (latest is w4/r0)
[   25.003999] UBIFS: default compressor: lzo
[   25.008112] UBIFS: reserved for root:  4952683 bytes (4836 KiB)
Begin: Running /scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... done.
[   25.130657] usb 1-1: new high speed USB device using orion-ehci and address 2
INIT: version 2.88 booting
[   25.302364] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[   25.309104] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[   25.316301] usb 1-1: Product: USB2.0 Hub
[   25.341179] usb 1-1: configuration #1 chosen from 1 choice
[   25.351056] hub 1-1:1.0: USB hub found
[   25.360482] hub 1-1:1.0: 4 ports detected
Using makefile-style concurrent boot in runlevel S.
Starting the hotplug events dispatcher: udevd[   25.716359] udev: starting version 160
.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...done.
Activating swap...done.
Checking root file system...fsck from util-linux-ng 2.17.2
[   26.521010] uncorrectable error :
[   32.846891] end_request: I/O error, dev mtdblock1, sector 0
(this repeats very often)

mount: special device UUID=619E-537A does not exist
failed.
Activating swapfile swap...done.
Cleaning up temporary files...find: cannot delete `./motd': Read-only file system
find: cannot delete `./dhclient.eth0.pid': Read-only file system
find: cannot delete `./sshd.pid': Read-only file system
bootclean: Failure cleaning /var/run. ... failed!
/lib/init/bootclean.sh: 188: cannot create /var/lock/.clean: Read-only file system
Setting kernel variables ...done.
Configuring network interfaces...ifup: failed to open statefile /etc/network/run/ifstate: Read-only file system
failed.
rm: cannot remove `/var/lib/urandom/random-seed': Read-only file system
Cleaning up temporary files...find: cannot delete `./motd': Read-only file system
find: cannot delete `./dhclient.eth0.pid': Read-only file system
find: cannot delete `./sshd.pid': Read-only file system
bootclean: Failure cleaning /var/run. ... failed!
/lib/init/bootclean.sh: 188: cannot create /var/lock/.clean: Read-only file system
/etc/init.d/bootmisc.sh: 63: cannot create /var/run/utmp: Read-only file system
startpar: service(s) returned failure: ifupdown-clean mountall-bootclean.sh mountnfs-bootclean.sh bootmisc.sh ... failed!
INIT: Entering runlevel: 2
Using makefile-style concurrent boot in runlevel 2.
Starting web server: apache2mkdir: cannot create directory `/var/run/apache2': Read-only file system
install: cannot change owner and permissions of `/var/lock/apache2': No such file or directory
[   33.897075] NET: Registered protocol family 10
[   33.903110] lo: Disabled Privacy Extensions
apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.0.1 for ServerName
(2)No such file or directory: apache2: could not open error log file /var/log/apache2/error.log.
Unable to open logs
Action 'start' failed.
The Apache error log may have more information.
 failed!
/etc/init.d/bootlogs: 74: cannot create /var/run/motd: Read-only file system
/etc/init.d/bootlogs: 74: cannot create /var/run/motd: Read-only file system
touch: cannot touch `/var/log/dmesg.new': Read-only file system
chown: cannot access `/var/log/dmesg.new': No such file or directory
chmod: cannot access `/var/log/dmesg.new': No such file or directory
ln: creating hard link `/var/log//dmesg.0': Read-only file system
Error hardlinking /var/log/dmesg to /var/log//dmesg.0
/etc/init.d/bootlogs: 74: cannot create /var/log/dmesg: Read-only file system
chgrp: changing group of `/var/log/dmesg': Read-only file system
Starting periodic command scheduler: cron/usr/sbin/cron: can't open or create /var/run/crond.pid: Read-only file system
 failed!
Starting MTA:open: Read-only file system
Starting OpenBSD Secure Shell server: sshd.
Starting Samba daemons:install: cannot change owner and permissions of `/var/run/samba': No such file or directory
 nmbd failed!
Starting Linux Video Disk Recorder: vdr - aborted (to enable the daemon, edit /etc/default/vdr).
startpar: service(s) returned failure: apache2 exim4 samba ... failed!
Running scripts in rc2.d/ took 2 seconds.

Debian GNU/Linux squeeze/sid debian ttyS0
Reply Quote
Hendrik
Re: Recovery via Serial: Not working as I don't get an IP
December 25, 2010 04:11AM
Oh dear...
I tried to re-install Debian on the NAND.

This failed when I entered: 
root@debian:~# flash_eraseall /dev/mtd3
Erasing 128 Kibyte @ db00000 -- 100 % complete.
root@debian:~# ubiformat /dev/mtd3 -y
Bus error
root@debian:~# ubiattach /dev/ubi_ctrl -m 3
Bus error
root@debian:~# ubimkvol /dev/ubi0 -m -N rootfs
Bus error
root@debian:~# dmesg
Bus error

Now the device is not booting anymore at all: 

U-Boot 2010.09 (Oct 23 2010 - 11:49:22)
Marvell-Dockstar/Pogoplug by Jeff Doozan

SoC:   Kirkwood 88F6281_A0
DRAM:  128 MiB
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
88E1116 Initialized on egiga0
Using egiga0 device
ping failed; host 192.168.178.27 is not alive
Hit any key to stop autoboot:  0
(Re)start USB...
USB:   Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... cannot reset port 4!?
2 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported

** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: empty MTD device detected
UBI: create volume table (copy #1)
UBI: create volume table (copy #2)
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=3"
UBI: MTD device size:            219 MiB
UBI: number of good PEBs:        1752
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     0
UBI: available PEBs:             1731
UBI: total number of reserved PEBs: 21
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 1/0
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: .......  read_nand_cached: error reading nand off 0x9da800 size 8192 bytes
read_nand_cached: error reading nand off 0xeb0200 size 8192 bytes
read_nand_cached: error reading nand off 0x1040000 size 8192 bytes
read_nand_cached: error reading nand off 0x1042000 size 8192 bytes
read_nand_cached: error reading nand off 0x1044000 size 8192 bytes
read_nand_cached: error reading nand off 0x1046000 size 8192 bytes
read_nand_cached: error reading nand off 0x1048000 size 8192 bytes
read_nand_cached: error reading nand off 0x104a000 size 8192 bytes
read_nand_cached: error reading nand off 0x104c000 size 8192 bytes
read_nand_cached: error reading nand off 0x104e000 size 8192 bytes
read_nand_cached: error reading nand off 0x1050000 size 8192 bytes
read_nand_cached: error reading nand off 0x1052000 size 8192 bytes
read_nand_cached: error reading nand off 0x1054000 size 8192 bytes
read_nand_cached: error reading nand off 0x1056000 size 8192 bytes
read_nand_cached: error reading nand off 0x1058000 size 8192 bytes
read_nand_cached: error reading nand off 0x105a000 size 8192 bytes
read_nand_cached: error reading nand off 0x105c000 size 8192 bytes
read_nand_cached: error reading nand off 0x105e000 size 8192 bytes                                                                                       .. done.
read_nand_cached: error reading nand off 0x9db800 size 8192 bytes
off = 0x9db100 magic 0x1985 type 0xe002 node.totlen = 1901
read_nand_cached: error reading nand off 0xeaf400 size 8192 bytes
off = 0xeaf150 magic 0x1985 type 0xe002 node.totlen = 2358
read_nand_cached: error reading nand off 0x103f200 size 8192 bytes
off = 0x103f1f4 magic 0x1985 type 0xe002 node.totlen = 2448
### JFFS2 load complete: 524288 bytes loaded to 0x800000
## Starting application at 0x00800200 ...


U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16)

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 00690D60

Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB  16bit width
Flash:  0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB

CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: REDSTONE:1.0

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME], egiga1
Hit any key to stop autoboot:  0
## Error: "bootcmd1" not defined
CE>>
CE>>
CE>> ping failed; host 192.168.178.27 is not alive
Hit any key to stop autoboot:  0
(Re)start USB...
USB:   Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported

** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=3"
UBI: MTD device size:            219 MiB
UBI: number of good PEBs:        1752
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     0
UBI: available PEBs:             1731
UBI: total number of reserved PEBs: 21
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: .......  read_nand_cached: error reading nand off 0x9da800 size 8192 bytes
read_nand_cached: error reading nand off 0xeb0200 size 8192 bytes
read_nand_cached: error reading nand off 0x1040000 size 8192 bytes
read_nand_cached: error reading nand off 0x1042000 size 8192 bytes
read_nand_cached: error reading nand off 0x1044000 size 8192 bytes
read_nand_cached: error reading nand off 0x1046000 size 8192 bytes
read_nand_cached: error reading nand off 0x1048000 size 8192 bytes
read_nand_cached: error reading nand off 0x104a000 size 8192 bytes
read_nand_cached: error reading nand off 0x104c000 size 8192 bytes
read_nand_cached: error reading nand off 0x104e000 size 8192 bytes
read_nand_cached: error reading nand off 0x1050000 size 8192 bytes
read_nand_cached: error reading nand off 0x1052000 size 8192 bytes
read_nand_cached: error reading nand off 0x1054000 size 8192 bytes
read_nand_cached: error reading nand off 0x1056000 size 8192 bytes
read_nand_cached: error reading nand off 0x1058000 size 8192 bytes
read_nand_cached: error reading nand off 0x105a000 size 8192 bytes
read_nand_cached: error reading nand off 0x105c000 size 8192 bytes
read_nand_cached: error reading nand off 0x105e000 size 8192 bytes                                                                                       .. done.
read_nand_cached: error reading nand off 0x9db800 size 8192 bytes
off = 0x9db100 magic 0x1985 type 0xe002 node.totlen = 1901
read_nand_cached: error reading nand off 0xeaf400 size 8192 bytes
off = 0xeaf150 magic 0x1985 type 0xe002 node.totlen = 2358
read_nand_cached: error reading nand off 0x103f200 size 8192 bytes
off = 0x103f1f4 magic 0x1985 type 0xe002 node.totlen = 2448
### JFFS2 load complete: 524288 bytes loaded to 0x800000
## Starting application at 0x00800200 ...


U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16)

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 00690D60

Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB  16bit width
Flash:  0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB

CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: REDSTONE:1.0

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME], egiga1
Hit any key to stop autoboot:  0
## Error: "bootcmd1" not defined

Now I'm lost.

Can anyone help?

I only get a shell

Regards,
Hendrik
Reply Quote
MadOCer
Re: Recovery via Serial: Not working as I don't get an IP
December 30, 2010 03:20PM
Type in "printenv" and it should tell you which commands are available. Obviously "bootcmd1" is not one of them. ;) The message doesn't mean that the system is defective. What it certainly means, though, is that your boot command is false.
Reply Quote
Newer Topic Older Topic
Author:

Your Email:


Subject:
Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: