Pogo V3 - No boot, no serial communication

1st time on this board with the following situation here.

It seems that I have a "dead" pogoplug V3 here. Tried to contact this with a JTAG/Serial connection, but no positive results. Reading this SATA Boot I now hope that I can make some progress. Links in that post are no longer working and therefore my SATA is not ready yet.
Planning to prepare a SATA SSD via a Linux computer but I'm lacking expert skills on bit level ;-)

My goal is to get this pogoplug up and running again and later see if I want to do more with it (most likely yes)..

Anyone any idea if my goals is feasible and how this is achieved.... Some help in initial steps is welcome.

Thnx in advance

Search the forum for shv posts. I recalled shv recently provided a good download link for this Sata booting download.

When you find it, please post the link here and I will confirm for you.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Here is shv's post that has a live link:
http://forum.doozan.com/read.php?3,16017,17297#msg-17297

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

I'm a major step forward (also in Time), but this log is currently the result. I'm trying to follow U-Boot installation, but I can't erase and flash as mentioned in this post.

Able to mount an USB Stick and of course boot via SATA (with some extra setenv commands). But I would like to get rid of the SATA and install U-boot.

Any ideas?



U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
Boot device: SATA
Attempting to set PLLA to 850 MHz ...
plla_ctrl0 : 0000020a
plla_ctrl1 : 00330000
plla_ctrl2 : 0065008b
plla_ctrl3 : 000000f1

PLLA Set
Bus 0: OK
Device 0:
** File not found /boot/bootargs.bin **


U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS

DRAM: 128 MiB
IDE: Bus 0: OK
Device 0: Model: STM3250318AS Firm: CC38 Ser#: 9VY5LZFJ
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net:
Led: GREEN
mii0
Main Loop
Hit any key to stop autoboot: 0
OX820 # setenv uinitrd_addr '0x60e00000'
OX820 # setenv uimage_addr '0x60500000'
OX820 # setenv dtb_addr '0x62c00000'
OX820 # setenv ide_set_bootargs 'setenv bootargs console=ttyS0,115200 root=/dev/sda1 rootdelay=10'
OX820 # setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
OX820 # setenv dt_load_dtb 'ext2load ide 0:1 $dtb_addr /boot/dts/ox820-pogoplug-pro.dtb'
OX820 # setenv dt_load_initrd 'ext2load ide 0:1 $uinitrd_addr /boot/uInitrd'
OX820 # setenv dt_load_uimage 'ext2load ide 0:1 $uimage_addr /boot/uImage'
OX820 # setenv dt_ide_boot 'run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm'
OX820 # setenv dt_ide_bootcmd 'run ide_set_bootargs; run dt_ide_boot'
OX820 # setenv dt_bootcmd_ide 'ide reset; run dt_ide_bootcmd; reset'
OX820 # setenv bootcmd 'run dt_bootcmd_ide'
OX820 # boot

Reset IDE: Bus 0: OK
Device 0: Model: STM3250318AS Firm: CC38 Ser#: 9VY5LZFJ
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
3676848 bytes read in 606 ms (5.8 MiB/s)
2103272 bytes read in 484 ms (4.1 MiB/s)
7029 bytes read in 61 ms (112.3 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-3.12.13-oxnas-tld-5
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3676784 Bytes = 3.5 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 60e00000 ...
Image Name: initramfs-3.12.13-oxnas-tld-5
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 2103208 Bytes = 2 MiB
Load Address: 60000000
Entry Point: 60000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
Booting using the fdt blob at 0x62c00000
Loading Kernel Image ... OK
Loading Ramdisk to 67c26000, end 67e277a8 ... OK
Loading Device Tree to 67c21000, end 67c25b74 ... OK

Led: GREEN

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.12.13-oxnas-tld-5 (root@tldDebian) (gcc version 4.6.3 (Debian 4.6.3-14) ) #3 SMP PREEMPT Mon May 12 17:42:03 PDT 2014
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: PLXTECH NAS782X SoC (Flattened Device Tree), model: Pogoplug Pro
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[ 0.000000] Start Ox820 platform
[ 0.000000] PERCPU: Embedded 7 pages/cpu @c0826000 s6656 r8192 d13824 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 120492K/131072K available (5186K kernel code, 234K rwdata, 1460K rodata, 158K init, 223K bss, 10580K reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0685b90 (6647 kB)
[ 0.000000] .init : 0xc0686000 - 0xc06ada00 ( 159 kB)
[ 0.000000] .data : 0xc06ae000 - 0xc06e8aa0 ( 235 kB)
[ 0.000000] .bss : 0xc06e8aac - 0xc0720868 ( 224 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:160
[ 0.000000] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 42949ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000184] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[ 0.050014] pid_max: default: 32768 minimum: 301
[ 0.050250] Mount-cache hash table entries: 512
[ 0.052794] CPU: Testing write buffer coherency: ok
[ 0.053194] Setting up static identity map for 0xc04ee9e8 - 0xc04eea20
[ 0.110351] CPU1: Booted secondary processor
[ 0.170163] Brought up 2 CPUs
[ 0.170188] SMP: Total of 2 processors activated.
[ 0.171284] devtmpfs: initialized
[ 0.174581] pinctrl core: initialized pinctrl subsystem
[ 0.174955] NET: Registered protocol family 16
[ 0.175431] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.178280] gpio-oxnas 44000000.gpio: at address c8846000
[ 0.178470] gpio-oxnas 44100000.gpio: at address c8848000
[ 0.178944] pinctrl-oxnas pinctrl.5: initialized OX820 pinctrl driver
[ 0.185361] bio: create slab <bio-0> at 0
[ 0.296138] oxnas-pcie 47c0: PCIe version/deviceID 0x82510b5
[ 0.296253] oxnas-pcie 47c0: link up
[ 0.296445] oxnas-pcie 47c0: PCI host bridge to bus 0000:00
[ 0.296468] pci_bus 0000:00: root bus resource [mem 0x48000000-0x49ffffff]
[ 0.296483] pci_bus 0000:00: root bus resource [mem 0x4a000000-0x4bdfffff pref]
[ 0.296501] pci_bus 0000:00: root bus resource [io 0x4be00000-0x4befffff]
[ 0.296519] pci_bus 0000:00: root bus resource [bus 00-7f]
[ 0.296867] PCI: bus0: Fast back to back transfers disabled
[ 0.296934] pci 0000:00:00.0: BAR 0: assigned [mem 0x48000000-0x4800ffff]
[ 0.297267] vgaarb: loaded
[ 0.297671] SCSI subsystem initialized
[ 0.298329] usbcore: registered new interface driver usbfs
[ 0.298403] usbcore: registered new interface driver hub
[ 0.298575] usbcore: registered new device driver usb
[ 0.298664] pps_core: LinuxPPS API ver. 1 registered
[ 0.298677] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.298711] PTP clock support registered
[ 0.299688] cfg80211: Calling CRDA to update world regulatory domain
[ 0.300823] Switched to clocksource rps_clocksource_timer
[ 0.312097] NET: Registered protocol family 2
[ 0.312844] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.312893] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.312926] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.313011] TCP: reno registered
[ 0.313036] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.313077] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.313408] NET: Registered protocol family 1
[ 0.313879] RPC: Registered named UNIX socket transport module.
[ 0.313896] RPC: Registered udp transport module.
[ 0.313907] RPC: Registered tcp transport module.
[ 0.313917] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.314222] Unpacking initramfs...
[ 0.526863] Freeing initrd memory: 2052K (c7c26000 - c7e27000)
[ 0.540392] NFS: Registering the id_resolver key type
[ 0.540459] Key type id_resolver registered
[ 0.540472] Key type id_legacy registered
[ 0.540497] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.541168] fuse init (API version 7.22)
[ 0.542131] msgmni has been set to 239
[ 0.606489] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.606512] io scheduler noop registered
[ 0.606525] io scheduler deadline registered
[ 0.606791] io scheduler cfq registered (default)
[ 0.607206] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.608302] 44200000.uart: ttyS0 at MMIO 0x44200000 (irq = 55, base_baud = 390625) is a 16550A
[ 1.121730] console [ttyS0] enabled
[ 1.126622] scsi0 : sata_oxnas
[ 1.129907] ata1: SATA max UDMA/133 irq 50
[ 1.134126] ox820sata: reseting SATA core
[ 1.135416] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
[ 1.135434] Scanning device for bad blocks
[ 1.218398] 2 ofpart partitions found on MTD device 41000000.nand
[ 1.224483] Creating 2 MTD partitions on "41000000.nand":
[ 1.229859] 0x000000000000-0x000000e00000 : "boot"
[ 1.235880] 0x000000e00000-0x000008000000 : "data"
[ 1.242250] stmmac - user ID: 0x12, Synopsys ID: 0x35
[ 1.247278] Ring mode enabled
[ 1.250311] DMA HW capability register supported
[ 1.254840] Enhanced/Alternate descriptors
[ 1.259169] Enabled extended descriptors
[ 1.263170] RX Checksum Offload Engine supported (type 2)
[ 1.268623] TX Checksum insertion supported
[ 1.272875] Wake-Up On Lan supported
[ 1.276515] Enable RX Mitigation via HW Watchdog Timer
[ 1.299223] libphy: stmmac: probed
[ 1.302650] eth0: PHY ID 001cc914 at 0 IRQ 0 (stmmac-0:00) active
[ 1.308718] eth0: PHY ID 001cc914 at 3 IRQ 0 (stmmac-0:03)
[ 1.314334] PCI: enabling device 0000:00:00.0 (0140 -> 0142)
[ 1.320140] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3090, rev 3213 detected
[ 1.331348] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0005 detected
[ 1.339686] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.346237] ehci-pci: EHCI PCI platform driver
[ 1.350976] oxnas-ehci 40200100.ehci: EHCI Host Controller
[ 1.356472] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[ 1.364239] oxnas-ehci 40200100.ehci: irq 39, io mem 0x40200100
[ 1.390438] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[ 1.396669] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.403453] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.410657] usb usb1: Product: EHCI Host Controller
[ 1.415511] usb usb1: Manufacturer: Linux 3.12.13-oxnas-tld-5 ehci_hcd
[ 1.422023] usb usb1: SerialNumber: 40200100.ehci
[ 1.427348] hub 1-0:1.0: USB hub found
[ 1.431206] hub 1-0:1.0: 2 ports detected
[ 1.435729] usbcore: registered new interface driver usb-storage
[ 1.442004] mousedev: PS/2 mouse device common for all mice
[ 1.448350] usbcore: registered new interface driver usbhid
[ 1.453926] usbhid: USB HID core driver
[ 1.458022] TCP: cubic registered
[ 1.462351] NET: Registered protocol family 10
[ 1.468144] sit: IPv6 over IPv4 tunneling driver
[ 1.473569] NET: Registered protocol family 17
[ 1.478156] Key type dns_resolver registered
[ 1.669987] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1.677235] ata1.00: ATA-8: STM3250318AS, CC38, max UDMA/133
[ 1.682910] ata1.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 1.690782] ata1.00: configured for UDMA/133
[ 1.710448] scsi 0:0:0:0: Direct-Access ATA STM3250318AS CC38 PQ: 0 ANSI: 5
[ 1.719321] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 1.727447] sd 0:0:0:0: [sda] Write Protect is off
[ 1.732456] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.750551] usb 1-1: new high-speed USB device number 2 using oxnas-ehci
[ 1.757376] sda: sda1
[ 1.761382] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.766213] Freeing unused kernel memory: 156K (c0686000 - c06ad000)
Loading, please wait...
[ 1.903377] udev[73]: starting version 164
[ 1.912442] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[ 1.919129] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 1.926284] usb 1-1: Product: USB2.0 Hub
[ 1.934215] hub 1-1:1.0: USB hub found
[ 1.981670] hub 1-1:1.0: 4 ports detected
[ 2.300595] usb 1-1.2: new high-speed USB device number 3 using oxnas-ehci
[ 2.411169] usb 1-1.2: New USB device found, idVendor=0204, idProduct=6025
[ 2.418024] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.425415] usb 1-1.2: Product: DatawriteVoyager
[ 2.430041] usb 1-1.2: Manufacturer: Pendrive
[ 2.434380] usb 1-1.2: SerialNumber: 172664037033
[ 2.441612] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 2.450759] scsi1 : usb-storage 1-1.2:1.0
[ 3.451415] scsi 1:0:0:0: Direct-Access Pendrive DatawriteVoyager 2.00 PQ: 0 ANSI: 2
[ 3.463703] sd 1:0:0:0: [sdb] 506879 4096-byte logical blocks: (2.07 GB/1.93 GiB)
[ 3.472010] sd 1:0:0:0: [sdb] Write Protect is off
[ 3.477363] sd 1:0:0:0: [sdb] No Caching mode page found
[ 3.483020] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 3.495610] sd 1:0:0:0: [sdb] 506879 4096-byte logical blocks: (2.07 GB/1.93 GiB)
[ 3.504215] sd 1:0:0:0: [sdb] No Caching mode page found
[ 3.509509] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 3.516513] sdb: sdb1
[ 3.524787] sd 1:0:0:0: [sdb] 506879 4096-byte logical blocks: (2.07 GB/1.93 GiB)
[ 3.534645] sd 1:0:0:0: [sdb] No Caching mode page found
[ 3.540049] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 3.546140] sd 1:0:0:0: [sdb] Attached SCSI removable disk
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
[ 12.599552] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
Begin: Running /scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... mount: mounting /dev on /root/dev failed: No such file or directory
done.
mount: mounting /sys on /root/sys failed: No such file or directory
mount: mounting /proc on /root/proc failed: No such file or directory
Target filesystem doesn't have requested /sbin/init.
No init found. Try passing init= bootarg.


BusyBox v1.17.1 (Debian 1:1.17.1-8) built-in shell (ash)
Enter 'help' for a list of built-in commands.

myhobby,

Congrats for successfully unbricked your box!

The boot log showed that you are booting from SATA with kernel 3.12.13-oxnas-tld-5. But the u-boot build was not my build.

Now before I can give you advice. I need the following info.

1. `How did you prepare the SATA disk to boot? was that from shv tarball?

2. Did you keep a log of what you did? can you post it here.

3. Do you have another Linux box where you can mount this disk and list these information. Assuming it is mounted at /media/sdb1 (if there is one partition on the disk), or mounted at /media/sdb1 and /media/sdb2 (if there are 2 partitions on the disk).

mount
e2label /dev/sdb1
e2label /dev/sdb2
ls -lart /media/sdb1/boot
ls -lart /media/sdb2/boot

Note that it there were errors in the output above, I need to see those too. So copy and paste the whole thing.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Let's see..


1. `How did you prepare the SATA disk to boot? was that from shv tarball?

I used this sticky until step 11.... (http://forum.doozan.com/read.php?3,32994), but it it can be that I overwrote the linux part with a different version. BTW creating a bootable disk via a Linux system was much harder than expected due to the technical level of documented help ;-) But I don't mind. (BTW why didn't someone create an harddisk image that can be downloaded and with tooling copied on an empty HDD (Win32DiskImager for Windows eg)

The reason for fiddeling around with versions is the fact that I don't want to loose my serial connection at any time, but I saw that the booted version is lower than what I "loaded" on the SATA drive. In other words, it seems that we have a mix of SATA and NAND boot ?

2. Did you keep a log of what you did? can you post it here.

In short, after creating a bootable disk, I saw that I was able to have a serial connection via putty. Again with additional info found here

Hit any key to stop autoboot: 0
OX820 # setenv uinitrd_addr '0x60e00000'
OX820 # setenv uimage_addr '0x60500000'
OX820 # setenv dtb_addr '0x62c00000'
OX820 # setenv ide_set_bootargs 'setenv bootargs console=ttyS0,115200 root=/dev/sda1 rootdelay=10'
OX820 # setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
OX820 # setenv dt_load_dtb 'ext2load ide 0:1 $dtb_addr /boot/dts/ox820-pogoplug-pro.dtb'
OX820 # setenv dt_load_initrd 'ext2load ide 0:1 $uinitrd_addr /boot/uInitrd'
OX820 # setenv dt_load_uimage 'ext2load ide 0:1 $uimage_addr /boot/uImage'
OX820 # setenv dt_ide_boot 'run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm'
OX820 # setenv dt_ide_bootcmd 'run ide_set_bootargs; run dt_ide_boot'
OX820 # setenv dt_bootcmd_ide 'ide reset; run dt_ide_bootcmd; reset'
OX820 # setenv bootcmd 'run dt_bootcmd_ide'
OX820 # boot

I was able to boot into a linux environment, missing the required pogoplug toolbox to write & read nands. By using my HDD as a portable device between the linux computer and the pogoplug, I was able to execute steps like NAND backup (I think).

USB sticks are currently automatically detected and can be mounted manually to a mountingpoint.



3. Do you have another Linux box where you can mount this disk and list these information. Assuming it is mounted at /media/sdb1 (if there is one partition on the disk), or mounted at /media/sdb1 and /media/sdb2 (if there are 2 partitions on the disk)

I know for sure that I only have 1 partion manually created on the bootable SATA drive... /dev/sda1 normally mounted manually to /media/rootfs. e2label /dev/sda1 -> rootfs.

Mounted /dev/sda1 -> Media/rootfs. Result of ls -lart /media/rootfs/boot

uImage_2.6.31.14_OX820_1.2_shv.Pro
u-boot.img
u-boot.env
uInitrd
dts [dir]
uImage
u-boot-spl.bin
local [dir create by me with tooling inside]

Does this help ?

myhobby,

> I used this sticky until step 11.... (http://forum.doozan.com/read.php?3,32994)
> Does this help ?

Yes. So now we know what you have in the SATA disk.

Where did you find this post? I could not. This was created by youxiaojie. I meant to put it in the Wiki, but forgot about it. And the fact that I could not find it in the u-boot subforum, I probably removed it by mistake (face palm). If I did, my appology to youxiaojie :)

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

bodhi Wrote:
-------------------------------------------------------

> Where did you find this post? I could not. This wa
> s created by youxiaojie. I meant to put it in the
> Wiki, but forgot about it. And the fact that I cou
> ld not find it in the u-boot subforum, I probably
> removed it by mistake (face palm). If I did, my ap
> pology to youxiaojie :)

Ok found it! It was weird, the timestamp is one day ahead of the original post time.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

myhobby,

Power up, interrupt serial console and execute

setenv ide_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10'
boot

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

And if you want to boot with USB rootfs, you will need to install the new u-boot to NAND.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS

DRAM: 128 MiB
IDE: Bus 0: OK
Device 0: Model: STM3250318AS Firm: CC38 Ser#: 9VY5LZFJ
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net:
Led: GREEN
mii0
Main Loop
Hit any key to stop autoboot: 0
OX820 # setenv ide_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL =rootfs rootdelay=10'
OX820 # boot
ide - IDE sub-system

Usage:
ide reset - reset IDE controller
ide info - show available IDE devices
ide device [dev] - show or set current device
ide part [dev] - print partition table of one or all IDE devices
ide read addr blk# cnt
ide write addr blk# cnt - read/write `cnt' blocks starting at block `blk#'
to/from memory address `addr'
2212156 bytes read in 417 ms (5.1 MiB/s)
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-2.6.31.14_OX820_1.2_shv
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2212092 Bytes = 2.1 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
Loading Kernel Image ... OK

Led: GREEN

Starting kernel ...

Uncompressing Linux............................................................. .......................................................................... done, booting the kernel.

<halt, no response>

And that is the end of this boot-attemp ;-)



My main goal is to create a pogoplug with a modified OS (ssh access) so I can use the original pogoplug functionality and additional extras

How-to (with U-boot) is not clear to me yet ;-)

There is a typo in this command:

setenv ide_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL =rootfs rootdelay=10'

Should be

setenv ide_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10'

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Okay, a bit stuck (but it is a hobby). Tried 2 different setenv and after that I ran printenv to show how this system initialize with the SATA drive


U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
Boot device: SATA
Attempting to set PLLA to 850 MHz ...
plla_ctrl0 : 0000020a
plla_ctrl1 : 00330000
plla_ctrl2 : 0065008b
plla_ctrl3 : 000000f1

PLLA Set
Bus 0: OK
Device 0:
** File not found /boot/bootargs.bin **


U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS

DRAM: 128 MiB
IDE: Bus 0: OK
Device 0: Model: STM3250318AS Firm: CC38 Ser#: 9VY5LZFJ
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net:
Led: GREEN
mii0
Main Loop
Hit any key to stop autoboot: 0

OX820 # setenv ide_set_bootargs 'setenv bootargs console=ttyS0,115200 root=/dev/sda1 rootdelay=10'
OX820 # <INTERRUPT>
OX820 # boot
ide - IDE sub-system

Usage:
ide reset - reset IDE controller
ide info - show available IDE devices
ide device [dev] - show or set current device
ide part [dev] - print partition table of one or all IDE devices
ide read addr blk# cnt
ide write addr blk# cnt - read/write `cnt' blocks starting at block `blk#'
to/from memory address `addr'
Unknown command 'setenv' - try 'help'
2212156 bytes read in 416 ms (5.1 MiB/s)
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-2.6.31.14_OX820_1.2_shv
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2212092 Bytes = 2.1 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
Loading Kernel Image ... OK

Led: GREEN

Starting kernel ...

Uncompressing Linux...................................................................................................................................... . done, booting the kernel.


********** System Hangs ************************

U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
Boot device: SATA
Attempting to set PLLA to 850 MHz ...
plla_ctrl0 : 0000020a
plla_ctrl1 : 00330000
plla_ctrl2 : 0065008b
plla_ctrl3 : 000000f1

PLLA Set
Bus 0: OK
Device 0:
** File not found /boot/bootargs.bin **


U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS

DRAM: 128 MiB
IDE: Bus 0: OK
Device 0: Model: STM3250318AS Firm: CC38 Ser#: 9VY5LZFJ
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net:
Led: GREEN
mii0
Main Loop
Hit any key to stop autoboot: 0

OX820 # setenv ide_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10'
OX820 # boot
ide - IDE sub-system

Usage:
ide reset - reset IDE controller
ide info - show available IDE devices
ide device [dev] - show or set current device
ide part [dev] - print partition table of one or all IDE devices
ide read addr blk# cnt
ide write addr blk# cnt - read/write `cnt' blocks starting at block `blk#'
to/from memory address `addr'
2212156 bytes read in 412 ms (5.1 MiB/s)
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-2.6.31.14_OX820_1.2_shv
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2212092 Bytes = 2.1 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
Loading Kernel Image ... OK

Led: GREEN

Starting kernel ...

Uncompressing Linux....................................................................................................................................... done, booting the kernel.

********** System Hangs ************************

U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
Boot device: SATA
Attempting to set PLLA to 850 MHz ...
plla_ctrl0 : 0000020a
plla_ctrl1 : 00330000
plla_ctrl2 : 0065008b
plla_ctrl3 : 000000f1

PLLA Set
Bus 0: OK
Device 0:
** File not found /boot/bootargs.bin **


U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS

DRAM: 128 MiB
IDE: Bus 0: OK
Device 0: Model: STM3250318AS Firm: CC38 Ser#: 9VY5LZFJ
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net:
Led: GREEN
mii0
Main Loop
Hit any key to stop autoboot: 0

****** type printenv after autoboot stop ***************

OX820 # printenv
dt_bootm=bootm $uimage_addr $uinitrd_addr $dtb_addr
autoload=no
baudrate=115200
bootargs=console=ttyS0,115200n8
bootcmd=run dt_bootcmd_ide
bootdelay=3
console=console=ttyS0,115200n8
dt_bootcmd_ide=ide start; run dt_ide_bootcmd; ide stop; reset
dt_bootcmd_usb=usb start; run dt_usb_bootcmd; usb stop; reset
dt_bootm=bootm $uimage_addr $uinitrd_addr $dtb_addr
dt_ide_boot=run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm
dt_ide_bootcmd=run ide_set_bootargs; run dt_sata_boot
dt_ide_load_dtb=ext2load ide 0:1 $dtb_addr /boot/dts/ox820-pogoplug-pro.dtb
dt_ide_load_initrd=ext2load ide 0:1 $uinitrd_addr /boot/uInitrd
dt_ide_load_uimage=ext2load ide 0:1 $uimage_addr /boot/uImage
dt_load_dtb=ext2load usb 0:1 $dtb_addr /boot/dts/ox820-pogoplug-pro.dtb
dt_load_initrd=ext2load usb 0:1 $uinitrd_addr /boot/uInitrd
dt_load_uimage=ext2load usb 0:1 $uimage_addr /boot/uImage
dt_sata_boot=ext2load ide 0:1 $uimage_addr /boot/uImage_2.6.31.14_OX820_1.2_shv.Pro; bootm $uimage_addr
dt_usb_boot=run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm
dt_usb_bootcmd=run usb_set_bootargs; run dt_usb_boot
dtb_addr=0x62c00000
ethact=mii0
ethaddr=00:25:31:01:C6:76
ide_set_bootargs=setenv bootargs root=/dev/sda2 rootfstype=ext3 console=ttyS0,115200 mem=128M
if_netconsole=ping $serverip
ipaddr=192.168.0.100
mtdids=nand0=41000000.nand
mtdparts=mtdparts=41000000.nand:14m(boot),-(data)
preboot_nc=run if_netconsole start_netconsole
sata_bootcmd=run usb_set_bootargs; run sata_boot
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version
stderr=serial
stdin=serial
stdout=serial
uimage_addr=0x60500000
uinitrd_addr=0x60e00000
usb_device=0:1
usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=/dev/sda1 rootdelay=10

Environment size: 1898/16380 bytes
OX820 #

myhobby,

Power up, interrupt serial console and,

setenv dt_bootcmd_ide 'ide reset; ide part; run dt_ide_bootcmd; reset'
setenv ide_set_bootargs 'setenv bootargs root=/dev/sda2 rootfstype=ext3 console=ttyS0,115200 mem=128M earlyprintk=serial'
printenv
boot

Please post the entire serial console log here.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

The result:

U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
  Boot device: SATA
Attempting to set PLLA to 850 MHz ...
  plla_ctrl0 : 0000020a
  plla_ctrl1 : 00330000
  plla_ctrl2 : 0065008b
  plla_ctrl3 : 000000f1

PLLA Set
Bus 0: OK
  Device 0:
** File not found /boot/bootargs.bin **


U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS

DRAM:  128 MiB
IDE:   Bus 0: OK
  Device 0: Model: STM3250318AS Firm: CC38 Ser#: 9VY5LZFJ
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:
Led:    GREEN
mii0
Main Loop
Hit any key to stop autoboot:  0
OX820 # setenv dt_bootcmd_ide 'ide reset; ide part; run dt_ide_bootcmd; reset'
OX820 # setenv ide_set_bootargs 'setenv bootargs root=/dev/sda2 rootfstype=ext3 console=ttyS0,115200 mem=128M earlyprintk=serial'
OX820 # printenv
dt_bootm=bootm $uimage_addr $uinitrd_addr $dtb_addr
autoload=no
baudrate=115200
bootargs=console=ttyS0,115200n8
bootcmd=run dt_bootcmd_ide
bootdelay=3
console=console=ttyS0,115200n8
dt_bootcmd_ide=ide reset; ide part; run dt_ide_bootcmd; reset
dt_bootcmd_usb=usb start; run dt_usb_bootcmd; usb stop; reset
dt_bootm=bootm $uimage_addr $uinitrd_addr $dtb_addr
dt_ide_boot=run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm
dt_ide_bootcmd=run ide_set_bootargs; run dt_sata_boot
dt_ide_load_dtb=ext2load ide 0:1 $dtb_addr /boot/dts/ox820-pogoplug-pro.dtb
dt_ide_load_initrd=ext2load ide 0:1 $uinitrd_addr /boot/uInitrd
dt_ide_load_uimage=ext2load ide 0:1 $uimage_addr /boot/uImage
dt_load_dtb=ext2load usb 0:1 $dtb_addr /boot/dts/ox820-pogoplug-pro.dtb
dt_load_initrd=ext2load usb 0:1 $uinitrd_addr /boot/uInitrd
dt_load_uimage=ext2load usb 0:1 $uimage_addr /boot/uImage
dt_sata_boot=ext2load ide 0:1 $uimage_addr /boot/uImage_2.6.31.14_OX820_1.2_shv.Pro; bootm $uimage_addr
dt_usb_boot=run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm
dt_usb_bootcmd=run usb_set_bootargs; run dt_usb_boot
dtb_addr=0x62c00000
ethact=mii0
ethaddr=00:25:31:01:C6:76
ide_set_bootargs=setenv bootargs root=/dev/sda2 rootfstype=ext3 console=ttyS0,115200 mem=128M earlyprintk=serial
if_netconsole=ping $serverip
ipaddr=192.168.0.100
mtdids=nand0=41000000.nand
mtdparts=mtdparts=41000000.nand:14m(boot),-(data)
preboot_nc=run if_netconsole start_netconsole
sata_bootcmd=run usb_set_bootargs; run sata_boot
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version
stderr=serial
stdin=serial
stdout=serial
uimage_addr=0x60500000
uinitrd_addr=0x60e00000
usb_device=0:1
usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=/dev/sda1 rootdelay=10

Environment size: 1917/16380 bytes
OX820 # boot

Reset IDE: Bus 0: OK
  Device 0: Model: STM3250318AS Firm: CC38 Ser#: 9VY5LZFJ
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)

Partition Map for IDE device 0  --   Partition Type: DOS

Part    Start Sector    Num Sectors     UUID            Type
  1     2048            488395120       00008000-01     0b
2212156 bytes read in 375 ms (5.6 MiB/s)
## Booting kernel from Legacy Image at 60500000 ...
   Image Name:   Linux-2.6.31.14_OX820_1.2_shv
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2212092 Bytes = 2.1 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

Led:    GREEN

Starting kernel ...

Uncompressing Linux....................................................................................................................................... done, booting the kernel.
[    0.000000] Linux version 2.6.31.14_OX820_1.2_shv (root@plug2) (gcc version 4.4.5 (Debian 4.4.5-8) ) #1 SMP Fri Oct 4 11:38:10 CEST 2013
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5387f
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[    0.000000] Machine: Oxsemi NAS
[    0.000000] 1 memory region
[    0.000000] Ignoring unrecognised tag 0x00000000
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: root=/dev/sda2 rootfstype=ext3 console=ttyS0,115200 mem=128M earlyprintk=serial
[    0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 128MB = 128MB total
[    0.000000] Memory: 125368KB available (3816K code, 304K data, 132K init, 0K highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:96
[    0.000000] OX820_RPS_init_irq: interrupts 64 to 96
[    0.010000] Console: colour dummy device 80x30
[    0.010000] console [ttyS0] enabled
[    0.020000] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[    0.230000] Security Framework initialized
[    0.230000] Mount-cache hash table entries: 512
[    0.240000] CPU: Testing write buffer coherency: ok
[    0.240000] Calibrating local timer... 424.49MHz.
[    0.310000] CPU1: Booted secondary processor
[    0.410000] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[    0.620000] Brought up 2 CPUs
[    0.630000] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[    0.640000] NET: Registered protocol family 16
[    0.640000] Number of DMA channels = 4, version = 4
[    0.650000] Reserving a DMA channel for DirectRAID
[    0.650000] Allocating 389 SRAM generic DMA descriptors
[    1.160000] PCIeA version/deviceID 082510b5
[    1.160000] PCIeB version/deviceID 082510b5
[    4.190000] ox820_pci_preinit() PCIEB link up timeout (00001814)
[    4.190000] ox820_pcie_setup_resources() Enabling PCIe Pre-Emphasis
[    4.200000] ox820_pciea_setup_resources() resource c7853f80
[    4.200000] ox820_pciea_setup_resources()    io:      0x4be00000 - 0x4befffff
[    4.210000] ox820_pciea_setup_resources()    non-pre: 0x48000000 - 0x49ffffff
[    4.220000] ox820_pciea_setup_resources()    pre:     0x4a000000 - 0x4bdfffff
[    4.220000] PCI: bus0: Fast back to back transfers disabled
[    4.230000] PCI: bus1: Fast back to back transfers enabled
[    4.250000] bio: create slab <bio-0> at 0
[    4.250000] SCSI subsystem initialized
[    4.260000] usbcore: registered new interface driver usbfs
[    4.260000] usbcore: registered new interface driver hub
[    4.270000] usbcore: registered new device driver usb
[    4.310000] NET: Registered protocol family 2
[    4.310000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    4.320000] Switched to NOHz mode on CPU #0
[    4.320000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    4.320000] Switched to NOHz mode on CPU #1
[    4.330000] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    4.340000] TCP: Hash tables configured (established 4096 bind 4096)
[    4.340000] TCP reno registered
[    4.350000] NET: Registered protocol family 1
[    4.350000] Create fragment cache
[    4.360000] fuse init (API version 7.12)
[    4.360000] msgmni has been set to 245
[    4.370000] alg: No test for stdrng (krng)
[    4.370000] io scheduler noop registered
[    4.380000] io scheduler anticipatory registered (default)
[    4.380000] io scheduler deadline registered
[    4.390000] io scheduler cfq registered
[    4.390000] ox820_gpio: initialized
[    4.410000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    4.420000] serial8250: ttyS0 at MMIO 0x44200000 (irq = 55) is a 16550A
[    4.430000] brd: module loaded
[    4.440000] loop: module loaded
[    4.440000] ox820sata: OX820 sata core.
[    4.450000] scsi0 : oxnassata
[    4.450000] scsi1 : oxnassata
[    4.460000] ata1: SATA max UDMA/133 irq 50
[    4.460000] ata2: SATA max UDMA/133 irq 50
[    4.460000] ox820sata: reseting SATA core
[    4.990000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    4.990000] ata1.00: ATA-8: STM3250318AS, CC38, max UDMA/133
[    5.000000] ata1.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[    5.010000] ata1.00: configured for UDMA/133
[    5.010000] ox820sata: reseting SATA core
[    5.720000] ata2: SATA link down (SStatus 0 SControl 300)
[    5.720000] scsi 0:0:0:0: Direct-Access     ATA      STM3250318AS     CC38 PQ: 0 ANSI: 5
[    5.730000] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[    5.740000] sd 0:0:0:0: [sda] Write Protect is off
[    5.740000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    5.750000] NAND: Page read time 40ms
[    5.750000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit)
[    5.750000] Scanning device for bad blocks
[    5.810000]  sda:
[    5.810000] Creating 2 MTD partitions on "NAND 128MiB 3,3V 8-bit":
[    5.820000] 0x000000000000-0x000000e00000 : "boot"
[    5.830000]  sda1
[    5.830000] 0x000000e00000-0x000008000000 : "rootfs"
[    5.830000] sd 0:0:0:0: [sda] Attached SCSI disk
[    5.840000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.850000] Start USB clocks
[    5.850000] oxnas-ehci oxnas-ehci.0: OXNAS EHCI Host Controller
[    5.860000] oxnas-ehci oxnas-ehci.0: new USB bus registered, assigned bus number 1
[    5.890000] oxnas-ehci oxnas-ehci.0: irq 39, io mem 0x00000000
[    5.910000] oxnas-ehci oxnas-ehci.0: USB 0.0 started, EHCI 1.00
[    5.910000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    5.920000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    5.920000] usb usb1: Product: OXNAS EHCI Host Controller
[    5.930000] usb usb1: Manufacturer: Linux 2.6.31.14_OX820_1.2_shv ehci_hcd
[    5.940000] usb usb1: SerialNumber: usb
[    5.940000] usb usb1: configuration #1 chosen from 1 choice
[    5.950000] hub 1-0:1.0: USB hub found
[    5.950000] hub 1-0:1.0: 2 ports detected
[    5.960000] Initializing USB Mass Storage driver...
[    5.960000] usbcore: registered new interface driver usb-storage
[    5.970000] USB Mass Storage support registered.
[    5.970000] usbcore: registered new interface driver libusual
[    5.980000] mice: PS/2 mouse device common for all mice
[    5.980000] TCP cubic registered
[    5.990000] NET: Registered protocol family 10
[    5.990000] NET: Registered protocol family 17
[    6.000000] RPC: Registered udp transport module.
[    6.000000] RPC: Registered tcp transport module.
[    6.010000] registered taskstats version 1
[    6.010000] VFS: Cannot open root device "sda2" or unknown-block(8,2)
[    6.020000] Please append a correct "root=" boot option; here are the available partitions:
[    6.030000] 0800       244198584 sda driver: sd
[    6.030000]   0801       244197560 sda1
[    6.040000] 1f00          131072 mtdblock0 (driver?)
[    6.040000] 1f01           14336 mtdblock1 (driver?)
[    6.050000] 1f02          116736 mtdblock2 (driver?)
[    6.050000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,2)
[    6.060000] CPU0: stopping
[    6.060000] [<c002f4c4>] (unwind_backtrace+0x0/0xe8) from [<c0029340>] (do_IPI+0xe4/0x148)
[    6.060000] [<c0029340>] (do_IPI+0xe4/0x148) from [<c0029c18>] (__irq_svc+0x38/0xc0)
[    6.060000] Exception stack(0xc03f9f58 to 0xc03f9fa0)
[    6.060000] 9f40:                                                       0263ca1a 00000000
[    6.090000] 9f60: c03f9fa0 00000000 c03f8000 c0421464 c03fe1bc c055a000 c042f484 000011a0
[    6.090000] 9f80: c03fdf00 c04211e0 ffff8d33 c03f9fa0 c002ab80 c002ab84 60000013 ffffffff
[    6.110000] [<c0029c18>] (__irq_svc+0x38/0xc0) from [<c002ab84>] (default_idle+0x24/0x28)
[    6.120000] [<c002ab84>] (default_idle+0x24/0x28) from [<c002b080>] (cpu_idle+0x64/0x98)
[    6.120000] [<c002b080>] (cpu_idle+0x64/0x98) from [<c0008b50>] (start_kernel+0x330/0x398)
[    6.130000] [<c0008b50>] (start_kernel+0x330/0x398) from [<60008084>] (0x60008084)

<< HALT, or no response....>>



Edited 1 time(s). Last edit at 09/07/2017 05:09AM by bodhi.

I don't quite remember what shv did. It seems you have only 1 partition on your HDD.

Please try again:

setenv dt_bootcmd_ide 'ide reset; ide part; run dt_ide_bootcmd; reset'
setenv ide_set_bootargs 'setenv bootargs root=/dev/sda1 rootfstype=ext3 console=ttyS0,115200 mem=128M earlyprintk=serial'
printenv
boot

If it still not booting, mount this HDD on another Linux box and get the output of (assuming it was mounted at /media/sdb1):

fdisk -l
e2label /dev/sdb1
ls -l /media/sdb1
ls - /media/sdb1/boot

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Still no boot....

@ubuntu:~$fdisk -l
 

Disk /dev/sda: 232.9 GiB, 250059350016 bytes, 488397168 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x00008000

Device     Boot Start       End   Sectors   Size Id Type
/dev/sda1        2048 488397167 488395120 232.9G  b W95 FAT32

Disk /dev/sdb: 465.8 GiB, 500107862016 bytes, 976773168 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x000d2702

Device     Boot     Start       End   Sectors   Size Id Type
/dev/sdb1  *         2048 968404991 968402944 461.8G 83 Linux
/dev/sdb2       968407038 976771071   8364034     4G  5 Extended
/dev/sdb5       968407040 976771071   8364032     4G 82 Linux swap / Solaris

@ubuntu:~$e2label /dev/sda1
rootfs

@ubuntu:~$mount /dev/sda1 /media/rootfs
@ubuntu:~$ls - /media/rootfs

/media/rootfs:
boot                                          lost+found
config-3.17.0-oxnas-tld-1                     
ox820-pogoplug-classic.dtb
linux-3.17.0-oxnas-tld-1.patch                
ox820-pogoplug-pro.dtb
linux-headers-3.17.0-oxnas-tld-1_1_armel.deb  
zImage-3.17.0-oxnas-tld-1
linux-image-3.17.0-oxnas-tld-1_1_armel.deb

@ubuntu:~$ ls - /media/rootfs/boot

/media/rootfs/boot:
u-boot.env  
u-boot-spl.bin  
uImage_2.6.31.14_OX820_1.2_shv.Pro
dts     
u-boot.img  
uImage          
uInitrd

@ubuntu:~$

Hopefully this helps for the next step. Sorry that it takes so long. Is not my intention. Thnx so far



Edited 1 time(s). Last edit at 09/07/2017 05:14AM by bodhi.

myhobby,

Please use these commands to list the files (I need to see the file attributes and sort it by time):

ls -lart /media/rootfs
ls -lart /media/rootfs/boot

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)



Edited 1 time(s). Last edit at 09/06/2017 05:51PM by bodhi.

Hopefully this helps ;-)

ubuntu:~$ ls -lart /media/rootfs
total 24408
drwxr-xr-x 4 root root     4096 Aug 13 09:46 ..
drwx------ 2 root root    16384 Aug 19 08:53 lost+found
-rw-r--r-- 1 root root 11067364 Aug 19 15:15 linux-image-3.17.0-oxnas-tld-1_1_armel.deb
-rw-r--r-- 1 root root  9105612 Aug 19 15:15 linux-headers-3.17.0-oxnas-tld-1_1_armel.deb
-rw-r--r-- 1 root root    98866 Aug 19 15:15 config-3.17.0-oxnas-tld-1
-rwxr-xr-x 1 root root  4102640 Aug 19 15:15 zImage-3.17.0-oxnas-tld-1
-rw-r--r-- 1 root root     7029 Aug 19 15:15 ox820-pogoplug-pro.dtb
-rw-r--r-- 1 root root     7033 Aug 19 15:15 ox820-pogoplug-classic.dtb
-rw-r--r-- 1 root root   561870 Aug 19 15:15 linux-3.17.0-oxnas-tld-1.patch
drwxr-xr-x 4 root root     4096 Aug 21 09:05 .
drwxr-xr-x 4 root root     4096 Aug 21 09:05 boot
ubuntu:~$ ls -lart /media/rootfs/boot
total 8392
-rw-r--r-- 1 root root 2212156 Aug 19 09:18 uImage_2.6.31.14_OX820_1.2_shv.Pro
-rw-r--r-- 1 root root  525880 Aug 19 09:18 u-boot.img
-rwxr-xr-x 1 root root   16384 Aug 19 09:18 u-boot.env
-rw-r--r-- 1 root root 2103272 Aug 19 09:18 uInitrd
drwxr-xr-x 2 root root    4096 Aug 19 09:18 dts
-rw-r--r-- 1 root root 3676848 Aug 19 09:18 uImage
-rwxr-xr-x 1 root root   32120 Aug 19 09:18 u-boot-spl.bin
drwxr-xr-x 4 root root    4096 Aug 21 09:05 ..
drwxr-xr-x 4 root root    4096 Aug 21 09:05 .

ubuntu:~$



Edited 1 time(s). Last edit at 09/07/2017 05:13AM by bodhi.

myhobby,

No, it did not help :) the date and time were not good. They don't reflect the time when the files were created, and in which order.


Try this.

Power up, interrupt serial console, and

setenv dt_sata_boot 'ext2load ide 0:1 $uimage_addr /boot/uImage_2.6.31.14_OX820_1.2_shv.Pro; ext2load ide 0:1 $uinitrd_addr /boot/uInitrd; bootm $uimage_addr $uinitrd_addr'
setenv dt_bootcmd_ide 'ide reset; ide part; run dt_ide_bootcmd; reset'
setenv ide_set_bootargs 'setenv bootargs root=LABEL=rootfs console=ttyS0,115200 mem=128M earlyprintk=serial'
printenv
boot

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)



Edited 1 time(s). Last edit at 09/07/2017 06:09PM by bodhi.

The result....

U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS

DRAM: 128 MiB
IDE: Bus 0: OK
Device 0: Model: STM3250318AS Firm: CC38 Ser#: 9VY5LZFJ
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net:
Led: GREEN
mii0
Main Loop
Hit any key to stop autoboot: 0
OX820 # setenv dt_sata_boot 'ext2load ide 0:1 $uimage_addr /boot/uImage_2.6.31.1 4_OX820_1.2_shv.Pro; ext2load ide 0:1 $uinitrd_addr /boot/uInitrd; bootm $uimage _addr $uinitrd_addr'
OX820 # setenv dt_bootcmd_ide 'ide reset; ide part; run dt_ide_bootcmd; reset'
OX820 # setenv ide_set_bootargs 'setenv bootargs root=LABEL=rootfs console=ttyS0 ,115200 mem=128M earlyprintk=serial'
OX820 # printenv
dt_bootm=bootm $uimage_addr $uinitrd_addr $dtb_addr
autoload=no
baudrate=115200
bootargs=console=ttyS0,115200n8
bootcmd=run dt_bootcmd_ide
bootdelay=3
console=console=ttyS0,115200n8
dt_bootcmd_ide=ide reset; ide part; run dt_ide_bootcmd; reset
dt_bootcmd_usb=usb start; run dt_usb_bootcmd; usb stop; reset
dt_bootm=bootm $uimage_addr $uinitrd_addr $dtb_addr
dt_ide_boot=run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm
dt_ide_bootcmd=run ide_set_bootargs; run dt_sata_boot
dt_ide_load_dtb=ext2load ide 0:1 $dtb_addr /boot/dts/ox820-pogoplug-pro.dtb
dt_ide_load_initrd=ext2load ide 0:1 $uinitrd_addr /boot/uInitrd
dt_ide_load_uimage=ext2load ide 0:1 $uimage_addr /boot/uImage
dt_load_dtb=ext2load usb 0:1 $dtb_addr /boot/dts/ox820-pogoplug-pro.dtb
dt_load_initrd=ext2load usb 0:1 $uinitrd_addr /boot/uInitrd
dt_load_uimage=ext2load usb 0:1 $uimage_addr /boot/uImage
dt_sata_boot=ext2load ide 0:1 $uimage_addr /boot/uImage_2.6.31.14_OX820_1.2_shv. Pro; ext2load ide 0:1 $uinitrd_addr /boot/uInitrd; bootm $uimage_addr $uinitrd_a ddr
dt_usb_boot=run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_boot m
dt_usb_bootcmd=run usb_set_bootargs; run dt_usb_boot
dtb_addr=0x62c00000
ethact=mii0
ethaddr=00:25:31:01:C6:76
ide_set_bootargs=setenv bootargs root=LABEL=rootfs console=ttyS0,115200 mem=128M earlyprintk=serial
if_netconsole=ping $serverip
ipaddr=192.168.0.100
mtdids=nand0=41000000.nand
mtdparts=mtdparts=41000000.nand:14m(boot),-(data)
preboot_nc=run if_netconsole start_netconsole
sata_bootcmd=run usb_set_bootargs; run sata_boot
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; se tenv stdout nc; setenv stderr nc; version
stderr=serial
stdin=serial
stdout=serial
uimage_addr=0x60500000
uinitrd_addr=0x60e00000
usb_device=0:1
usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=/dev/sda1 rootdelay=1 0

Environment size: 1964/16380 bytes
OX820 # boot

Reset IDE: Bus 0: OK
Device 0: Model: STM3250318AS Firm: CC38 Ser#: 9VY5LZFJ
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)

Partition Map for IDE device 0 -- Partition Type: DOS

Part Start Sector Num Sectors UUID Type
1 2048 488395120 00008000-01 0b
2212156 bytes read in 376 ms (5.6 MiB/s)
2103272 bytes read in 461 ms (4.4 MiB/s)
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-2.6.31.14_OX820_1.2_shv
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2212092 Bytes = 2.1 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 60e00000 ...
Image Name: initramfs-3.12.13-oxnas-tld-5
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 2103208 Bytes = 2 MiB
Load Address: 60000000
Entry Point: 60000000
Verifying Checksum ... OK
Loading Kernel Image ... OK

Led: GREEN

Starting kernel ...

Uncompressing Linux............................................................. .......................................................................... done, booting the kernel.
[ 0.000000] Linux version 2.6.31.14_OX820_1.2_shv (root@plug2) (gcc version 4 .4.5 (Debian 4.4.5-8) ) #1 SMP Fri Oct 4 11:38:10 CEST 2013
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr =00c5387f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction ca che
[ 0.000000] Machine: Oxsemi NAS
[ 0.000000] 1 memory region
[ 0.000000] Ignoring unrecognised tag 0x00000000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 32512
[ 0.000000] Kernel command line: root=LABEL=rootfs console=ttyS0,115200 mem=1 28M earlyprintk=serial
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 128MB = 128MB total
[ 0.000000] Memory: 123304KB available (3816K code, 304K data, 132K init, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:96
[ 0.000000] OX820_RPS_init_irq: interrupts 64 to 96
[ 0.010000] Console: colour dummy device 80x30
[ 0.010000] console [ttyS0] enabled
[ 0.020000] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[ 0.230000] Security Framework initialized
[ 0.230000] Mount-cache hash table entries: 512
[ 0.240000] CPU: Testing write buffer coherency: ok
[ 0.240000] Calibrating local timer... 425.50MHz.
[ 0.310000] CPU1: Booted secondary processor
[ 0.410000] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[ 0.620000] Brought up 2 CPUs
[ 0.630000] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[ 0.640000] NET: Registered protocol family 16
[ 0.640000] Number of DMA channels = 4, version = 4
[ 0.650000] Reserving a DMA channel for DirectRAID
[ 0.650000] Allocating 389 SRAM generic DMA descriptors
[ 1.160000] PCIeA version/deviceID 082510b5
[ 1.160000] PCIeB version/deviceID 082510b5
[ 4.190000] ox820_pci_preinit() PCIEB link up timeout (00001814)
[ 4.190000] ox820_pcie_setup_resources() Enabling PCIe Pre-Emphasis
[ 4.200000] ox820_pciea_setup_resources() resource c7853f80
[ 4.200000] ox820_pciea_setup_resources() io: 0x4be00000 - 0x4befffff
[ 4.210000] ox820_pciea_setup_resources() non-pre: 0x48000000 - 0x49ffffff
[ 4.220000] ox820_pciea_setup_resources() pre: 0x4a000000 - 0x4bdfffff
[ 4.220000] PCI: bus0: Fast back to back transfers disabled
[ 4.230000] PCI: bus1: Fast back to back transfers enabled
[ 4.250000] bio: create slab <bio-0> at 0
[ 4.250000] SCSI subsystem initialized
[ 4.260000] usbcore: registered new interface driver usbfs
[ 4.260000] usbcore: registered new interface driver hub
[ 4.270000] usbcore: registered new device driver usb
[ 4.310000] NET: Registered protocol family 2
[ 4.310000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 4.320000] Switched to NOHz mode on CPU #0
[ 4.320000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 4.320000] Switched to NOHz mode on CPU #1
[ 4.330000] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 4.340000] TCP: Hash tables configured (established 4096 bind 4096)
[ 4.340000] TCP reno registered
[ 4.350000] NET: Registered protocol family 1
[ 4.350000] Trying to unpack rootfs image as initramfs...
[ 4.540000] Freeing initrd memory: 2052K
[ 4.550000] Create fragment cache
[ 4.550000] fuse init (API version 7.12)
[ 4.560000] msgmni has been set to 245
[ 4.560000] alg: No test for stdrng (krng)
[ 4.570000] io scheduler noop registered
[ 4.570000] io scheduler anticipatory registered (default)
[ 4.580000] io scheduler deadline registered
[ 4.580000] io scheduler cfq registered
[ 4.580000] ox820_gpio: initialized
[ 4.600000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 4.610000] serial8250: ttyS0 at MMIO 0x44200000 (irq = 55) is a 16550A
[ 4.630000] brd: module loaded
[ 4.630000] loop: module loaded
[ 4.640000] ox820sata: OX820 sata core.
[ 4.640000] scsi0 : oxnassata
[ 4.650000] scsi1 : oxnassata
[ 4.650000] ata1: SATA max UDMA/133 irq 50
[ 4.650000] ata2: SATA max UDMA/133 irq 50
[ 4.660000] ox820sata: reseting SATA core
[ 5.180000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 5.180000] ata1.00: ATA-8: STM3250318AS, CC38, max UDMA/133
[ 5.190000] ata1.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 5.200000] ata1.00: configured for UDMA/133
[ 5.200000] ox820sata: reseting SATA core
[ 5.910000] ata2: SATA link down (SStatus 0 SControl 300)
[ 5.910000] scsi 0:0:0:0: Direct-Access ATA STM3250318AS CC38 PQ : 0 ANSI: 5
[ 5.920000] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 5.930000] sd 0:0:0:0: [sda] Write Protect is off
[ 5.930000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, does n't support DPO or FUA
[ 5.940000] NAND: Page read time 40ms
[ 5.940000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128 MiB 3,3V 8-bit)
[ 5.940000] Scanning device for bad blocks
[ 6.000000] sda:
[ 6.000000] Creating 2 MTD partitions on "NAND 128MiB 3,3V 8-bit":
[ 6.010000] 0x000000000000-0x000000e00000 : "boot"
[ 6.020000] 0x000000e00000-0x000008000000 : "rootfs"
[ 6.020000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.030000] Start USB clocks
[ 6.030000] oxnas-ehci oxnas-ehci.0: OXNAS EHCI Host Controller
[ 6.040000] oxnas-ehci oxnas-ehci.0: new USB bus registered, assigned bus num ber 1
[ 6.050000] sda1
[ 6.050000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 6.080000] oxnas-ehci oxnas-ehci.0: irq 39, io mem 0x00000000
[ 6.100000] oxnas-ehci oxnas-ehci.0: USB 0.0 started, EHCI 1.00
[ 6.100000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 6.110000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
[ 6.110000] usb usb1: Product: OXNAS EHCI Host Controller
[ 6.120000] usb usb1: Manufacturer: Linux 2.6.31.14_OX820_1.2_shv ehci_hcd
[ 6.130000] usb usb1: SerialNumber: usb
[ 6.130000] usb usb1: configuration #1 chosen from 1 choice
[ 6.140000] hub 1-0:1.0: USB hub found
[ 6.140000] hub 1-0:1.0: 2 ports detected
[ 6.150000] Initializing USB Mass Storage driver...
[ 6.150000] usbcore: registered new interface driver usb-storage
[ 6.160000] USB Mass Storage support registered.
[ 6.160000] usbcore: registered new interface driver libusual
[ 6.170000] mice: PS/2 mouse device common for all mice
[ 6.170000] TCP cubic registered
[ 6.180000] NET: Registered protocol family 10
[ 6.180000] NET: Registered protocol family 17
[ 6.190000] RPC: Registered udp transport module.
[ 6.190000] RPC: Registered tcp transport module.
[ 6.200000] registered taskstats version 1
[ 6.200000] Freeing init memory: 132K
Loading, please wait...
modprobe: FATAL: Could not load /lib/modules/2.6.31.14_OX820_1.2_shv/modules.dep : No such file or directory

mount: mounting none on /dev failed: No such device
W: devtmpfs not available, falling back to tmpfs for /dev
[ 6.470000] usb 1-1: new high speed USB device using oxnas-ehci and address 2
[ 6.620000] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[ 6.620000] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 6.630000] usb 1-1: Product: USB2.0 Hub
[ 6.640000] usb 1-1: configuration #1 chosen from 1 choice
[ 6.640000] hub 1-1:1.0: USB hub found
[ 6.650000] hub 1-1:1.0: 4 ports detected
FATAL: Could not load /lib/modules/2.6.31.14_OX820_1.2_shv/modules.dep: No such file or directory
Begin: Loading essential drivers ... FATAL: Could not load /lib/modules/2.6.31.1 4_OX820_1.2_shv/modules.dep: No such file or directory
done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
FATAL: Could not load /lib/modules/2.6.31.14_OX820_1.2_shv/modules.dep: No such file or directory
modprobe: FATAL: Could not load /lib/modules/2.6.31.14_OX820_1.2_shv/modules.dep : No such file or directory

mount: mounting /dev/disk/by-label/rootfs on /root failed: No such device
Begin: Running /scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... mount: mounting /dev on /root/dev failed : No such file or directory
done.
mount: mounting /sys on /root/sys failed: No such file or directory
mount: mounting /proc on /root/proc failed: No such file or directory
Target filesystem doesn't have requested /sbin/init.
FATAL: Could not load /lib/modules/2.6.31.14_OX820_1.2_shv/modules.dep: No such file or directory
FATAL: Could not load /lib/modules/2.6.31.14_OX820_1.2_shv/modules.dep: No such file or directory
No init found. Try passing init= bootarg.


BusyBox v1.17.1 (Debian 1:1.17.1-8) built-in shell (ash)
Enter 'help' for a list of built-in commands.

/bin/sh: can't access tty; job control turned off
(initramfs)

myhobby,

It seems shv built the kernel in this rootfs without initrd. That's what the error meant.

Let's not dwell on this HDD rootfs (eventually you want to replace it anyway because it is quite old).

Create the new rootfs on USB using Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2. And then I'll help you boot that latest stretch rootfs.

http://forum.doozan.com/read.php?2,16044

Scroll down to section:

Quote

Updated 02 Aug 2017:

Rootfs Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2 was uploaded.

Basic Debian stretch Oxnas rootfs for Popo Pro/Classic V3 plug:

- tarball size: 180M
- install size: 477M
- Installed packages: nano, avahi, ntp, busybox-syslogd (log to RAM), htop, dialog, bz2, iperf, ethtool, sysvinit-core, sysvinit, sysvinit-utils, mtd-utils.
- see LED controls in /etc/rc.local, and /etc/rc0.d/K08halt
- see some useful aliases in /root/.profile
- root password: root

Note: you must skip step 4 (Create uImage with embedded DTB for booting with stock u-boot).

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Again a step forward. USB stick create and guessed some previous setenv. Look at the results


U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
Boot device: SATA
Attempting to set PLLA to 850 MHz ...
plla_ctrl0 : 0000020a
plla_ctrl1 : 00330000
plla_ctrl2 : 0065008b
plla_ctrl3 : 000000f1

PLLA Set
Bus 0: OK
Device 0:
** File not found /boot/bootargs.bin **


U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS

DRAM: 128 MiB
IDE: Bus 0: OK
Device 0: Model: STM3250318AS Firm: CC38 Ser#: 9VY5LZFJ
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net:
Led: GREEN
mii0
Main Loop
Hit any key to stop autoboot: 0
OX820 # setenv ide_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10'
OX820 # setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
OX820 # setenv dt_load_dtb 'ext2load ide 0:1 $dtb_addr /boot/dts/ox820-pogoplug-pro.dtb'
OX820 # setenv dt_load_initrd 'ext2load ide 0:1 $uinitrd_addr /boot/uInitrd'
OX820 # setenv dt_load_uimage 'ext2load ide 0:1 $uimage_addr /boot/uImage'
OX820 # setenv dt_ide_boot 'run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm'
OX820 # setenv dt_ide_bootcmd 'run ide_set_bootargs; run dt_ide_boot'
OX820 # setenv dt_bootcmd_ide 'ide reset; run dt_ide_bootcmd; reset'
OX820 # setenv bootcmd 'run dt_bootcmd_ide'
OX820 # printenv
dt_bootm=bootm $uimage_addr $uinitrd_addr $dtb_addr
autoload=no
baudrate=115200
bootargs=console=ttyS0,115200n8
bootcmd=run dt_bootcmd_ide
bootdelay=3
console=console=ttyS0,115200n8
dt_bootcmd_ide=ide reset; run dt_ide_bootcmd; reset
dt_bootcmd_usb=usb start; run dt_usb_bootcmd; usb stop; reset
dt_bootm=bootm $uimage_addr $uinitrd_addr $dtb_addr
dt_ide_boot=run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm
dt_ide_bootcmd=run ide_set_bootargs; run dt_ide_boot
dt_ide_load_dtb=ext2load ide 0:1 $dtb_addr /boot/dts/ox820-pogoplug-pro.dtb
dt_ide_load_initrd=ext2load ide 0:1 $uinitrd_addr /boot/uInitrd
dt_ide_load_uimage=ext2load ide 0:1 $uimage_addr /boot/uImage
dt_load_dtb=ext2load ide 0:1 $dtb_addr /boot/dts/ox820-pogoplug-pro.dtb
dt_load_initrd=ext2load ide 0:1 $uinitrd_addr /boot/uInitrd
dt_load_uimage=ext2load ide 0:1 $uimage_addr /boot/uImage
dt_sata_boot=ext2load ide 0:1 $uimage_addr /boot/uImage_2.6.31.14_OX820_1.2_shv.Pro; bootm $uimage_addr
dt_usb_boot=run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm
dt_usb_bootcmd=run usb_set_bootargs; run dt_usb_boot
dtb_addr=0x62c00000
ethact=mii0
ethaddr=00:25:31:01:C6:76
ide_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10
if_netconsole=ping $serverip
ipaddr=192.168.0.100
mtdids=nand0=41000000.nand
mtdparts=mtdparts=41000000.nand:14m(boot),-(data)
preboot_nc=run if_netconsole start_netconsole
sata_bootcmd=run usb_set_bootargs; run sata_boot
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version
stderr=serial
stdin=serial
stdout=serial
uimage_addr=0x60500000
uinitrd_addr=0x60e00000
usb_device=0:1
usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=/dev/sda1 rootdelay=10

Environment size: 1866/16380 bytes
OX820 # boot

Reset IDE: Bus 0: OK
Device 0: Model: STM3250318AS Firm: CC38 Ser#: 9VY5LZFJ
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
3676848 bytes read in 606 ms (5.8 MiB/s)
2103272 bytes read in 484 ms (4.1 MiB/s)
7029 bytes read in 60 ms (114.3 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-3.12.13-oxnas-tld-5
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3676784 Bytes = 3.5 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 60e00000 ...
Image Name: initramfs-3.12.13-oxnas-tld-5
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 2103208 Bytes = 2 MiB
Load Address: 60000000
Entry Point: 60000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
Booting using the fdt blob at 0x62c00000
Loading Kernel Image ... OK
Loading Ramdisk to 67c26000, end 67e277a8 ... OK
Loading Device Tree to 67c21000, end 67c25b74 ... OK

Led: GREEN

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.12.13-oxnas-tld-5 (root@tldDebian) (gcc version 4.6.3 (Debian 4.6.3-14) ) #3 SMP PREEMPT Mon May 12 17:42:03 PDT 2014
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: PLXTECH NAS782X SoC (Flattened Device Tree), model: Pogoplug Pro
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[ 0.000000] Start Ox820 platform
[ 0.000000] PERCPU: Embedded 7 pages/cpu @c0826000 s6656 r8192 d13824 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 120492K/131072K available (5186K kernel code, 234K rwdata, 1460K rodata, 158K init, 223K bss, 10580K reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0685b90 (6647 kB)
[ 0.000000] .init : 0xc0686000 - 0xc06ada00 ( 159 kB)
[ 0.000000] .data : 0xc06ae000 - 0xc06e8aa0 ( 235 kB)
[ 0.000000] .bss : 0xc06e8aac - 0xc0720868 ( 224 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:160
[ 0.000000] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 42949ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000184] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[ 0.050014] pid_max: default: 32768 minimum: 301
[ 0.050250] Mount-cache hash table entries: 512
[ 0.052802] CPU: Testing write buffer coherency: ok
[ 0.053199] Setting up static identity map for 0xc04ee9e8 - 0xc04eea20
[ 0.110356] CPU1: Booted secondary processor
[ 0.170163] Brought up 2 CPUs
[ 0.170186] SMP: Total of 2 processors activated.
[ 0.171274] devtmpfs: initialized
[ 0.174563] pinctrl core: initialized pinctrl subsystem
[ 0.174935] NET: Registered protocol family 16
[ 0.175413] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.178355] gpio-oxnas 44000000.gpio: at address c8846000
[ 0.178536] gpio-oxnas 44100000.gpio: at address c8848000
[ 0.179054] pinctrl-oxnas pinctrl.5: initialized OX820 pinctrl driver
[ 0.185638] bio: create slab <bio-0> at 0
[ 0.296419] oxnas-pcie 47c0: PCIe version/deviceID 0x82510b5
[ 0.296537] oxnas-pcie 47c0: link up
[ 0.296734] oxnas-pcie 47c0: PCI host bridge to bus 0000:00
[ 0.296760] pci_bus 0000:00: root bus resource [mem 0x48000000-0x49ffffff]
[ 0.296775] pci_bus 0000:00: root bus resource [mem 0x4a000000-0x4bdfffff pref]
[ 0.296791] pci_bus 0000:00: root bus resource [io 0x4be00000-0x4befffff]
[ 0.296808] pci_bus 0000:00: root bus resource [bus 00-7f]
[ 0.297159] PCI: bus0: Fast back to back transfers disabled
[ 0.297228] pci 0000:00:00.0: BAR 0: assigned [mem 0x48000000-0x4800ffff]
[ 0.297561] vgaarb: loaded
[ 0.297935] SCSI subsystem initialized
[ 0.298603] usbcore: registered new interface driver usbfs
[ 0.298677] usbcore: registered new interface driver hub
[ 0.298851] usbcore: registered new device driver usb
[ 0.298946] pps_core: LinuxPPS API ver. 1 registered
[ 0.298959] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.298992] PTP clock support registered
[ 0.300052] cfg80211: Calling CRDA to update world regulatory domain
[ 0.301204] Switched to clocksource rps_clocksource_timer
[ 0.313034] NET: Registered protocol family 2
[ 0.313789] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.313840] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.313876] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.313955] TCP: reno registered
[ 0.313978] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.314019] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.314355] NET: Registered protocol family 1
[ 0.314816] RPC: Registered named UNIX socket transport module.
[ 0.314833] RPC: Registered udp transport module.
[ 0.314846] RPC: Registered tcp transport module.
[ 0.314856] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.315166] Unpacking initramfs...
[ 0.527677] Freeing initrd memory: 2052K (c7c26000 - c7e27000)
[ 0.541140] NFS: Registering the id_resolver key type
[ 0.541201] Key type id_resolver registered
[ 0.541214] Key type id_legacy registered
[ 0.541240] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.541941] fuse init (API version 7.22)
[ 0.542929] msgmni has been set to 239
[ 0.607603] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.607623] io scheduler noop registered
[ 0.607633] io scheduler deadline registered
[ 0.607897] io scheduler cfq registered (default)
[ 0.608279] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.609346] 44200000.uart: ttyS0 at MMIO 0x44200000 (irq = 55, base_baud = 390625) is a 16550A
[ 1.123153] console [ttyS0] enabled
[ 1.128061] scsi0 : sata_oxnas
[ 1.131394] ata1: SATA max UDMA/133 irq 50
[ 1.135575] ox820sata: reseting SATA core
[ 1.136811] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
[ 1.136829] Scanning device for bad blocks
[ 1.219975] 2 ofpart partitions found on MTD device 41000000.nand
[ 1.226060] Creating 2 MTD partitions on "41000000.nand":
[ 1.231449] 0x000000000000-0x000000e00000 : "boot"
[ 1.237478] 0x000000e00000-0x000008000000 : "data"
[ 1.243860] stmmac - user ID: 0x12, Synopsys ID: 0x35
[ 1.248888] Ring mode enabled
[ 1.251950] DMA HW capability register supported
[ 1.256458] Enhanced/Alternate descriptors
[ 1.260802] Enabled extended descriptors
[ 1.264793] RX Checksum Offload Engine supported (type 2)
[ 1.270246] TX Checksum insertion supported
[ 1.274503] Wake-Up On Lan supported
[ 1.278144] Enable RX Mitigation via HW Watchdog Timer
[ 1.300838] libphy: stmmac: probed
[ 1.304235] eth0: PHY ID 001cc914 at 0 IRQ 0 (stmmac-0:00) active
[ 1.310297] eth0: PHY ID 001cc914 at 3 IRQ 0 (stmmac-0:03)
[ 1.315911] PCI: enabling device 0000:00:00.0 (0140 -> 0142)
[ 1.321720] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3090, rev 3213 detected
[ 1.332907] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0005 detected
[ 1.341273] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.347770] ehci-pci: EHCI PCI platform driver
[ 1.352512] oxnas-ehci 40200100.ehci: EHCI Host Controller
[ 1.358005] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[ 1.365777] oxnas-ehci 40200100.ehci: irq 39, io mem 0x40200100
[ 1.390451] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[ 1.396697] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.403481] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.410682] usb usb1: Product: EHCI Host Controller
[ 1.415539] usb usb1: Manufacturer: Linux 3.12.13-oxnas-tld-5 ehci_hcd
[ 1.422049] usb usb1: SerialNumber: 40200100.ehci
[ 1.427368] hub 1-0:1.0: USB hub found
[ 1.431191] hub 1-0:1.0: 2 ports detected
[ 1.435701] usbcore: registered new interface driver usb-storage
[ 1.441981] mousedev: PS/2 mouse device common for all mice
[ 1.448371] usbcore: registered new interface driver usbhid
[ 1.453964] usbhid: USB HID core driver
[ 1.458063] TCP: cubic registered
[ 1.462353] NET: Registered protocol family 10
[ 1.468111] sit: IPv6 over IPv4 tunneling driver
[ 1.473528] NET: Registered protocol family 17
[ 1.478077] Key type dns_resolver registered
[ 1.669987] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1.677163] ata1.00: ATA-8: STM3250318AS, CC38, max UDMA/133
[ 1.682833] ata1.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 1.690629] ata1.00: configured for UDMA/133
[ 1.710440] scsi 0:0:0:0: Direct-Access ATA STM3250318AS CC38 PQ: 0 ANSI: 5
[ 1.719667] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 1.727549] sd 0:0:0:0: [sda] Write Protect is off
[ 1.732587] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.750545] usb 1-1: new high-speed USB device number 2 using oxnas-ehci
[ 1.757373] sda: sda1
[ 1.761379] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.766233] Freeing unused kernel memory: 156K (c0686000 - c06ad000)
Loading, please wait...
[ 1.903208] udev[73]: starting version 164
[ 1.912350] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[ 1.919029] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 1.926423] usb 1-1: Product: USB2.0 Hub
[ 1.931607] hub 1-1:1.0: USB hub found
[ 1.938708] hub 1-1:1.0: 4 ports detected
[ 2.231503] usb 1-1.2: new high-speed USB device number 3 using oxnas-ehci
[ 2.351449] usb 1-1.2: New USB device found, idVendor=0204, idProduct=6025
[ 2.358307] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.365644] usb 1-1.2: Product: DatawriteVoyager
[ 2.370247] usb 1-1.2: Manufacturer: Pendrive
[ 2.375426] usb 1-1.2: SerialNumber: 172664037033
[ 2.382141] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 2.389393] scsi1 : usb-storage 1-1.2:1.0
[ 3.391441] scsi 1:0:0:0: Direct-Access Pendrive DatawriteVoyager 2.00 PQ: 0 ANSI: 2
[ 3.403627] sd 1:0:0:0: [sdb] 506879 4096-byte logical blocks: (2.07 GB/1.93 GiB)
[ 3.412032] sd 1:0:0:0: [sdb] Write Protect is off
[ 3.417408] sd 1:0:0:0: [sdb] No Caching mode page found
[ 3.422804] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 3.435640] sd 1:0:0:0: [sdb] 506879 4096-byte logical blocks: (2.07 GB/1.93 GiB)
[ 3.444126] sd 1:0:0:0: [sdb] No Caching mode page found
[ 3.449420] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 3.456299] sdb: sdb1
[ 3.464696] sd 1:0:0:0: [sdb] 506879 4096-byte logical blocks: (2.07 GB/1.93 GiB)
[ 3.474432] sd 1:0:0:0: [sdb] No Caching mode page found
[ 3.479746] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 3.486458] sd 1:0:0:0: [sdb] Attached SCSI removable disk
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
[ 12.685898] kjournald starting. Commit interval 5 seconds
[ 12.686005] EXT3-fs (sdb1): mounted filesystem with ordered data mode
Begin: Running /scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232
. ok
[ ok ] Synthesizing the initial hotplug events...done.
[ ok ] Waiting for /dev to be fully populated...done.
[ ok ] Activating swap...done.
[....] Checking root file system...fsck from util-linux 2.29.2
rootfs: clean, 14005/126720 files, 130303/506623 blocks
done.
[ 31.147304] EXT3-fs (sdb1): using internal journal
[ ok ] Activating lvm and md swap...done.
[....] Checking file systems...fsck from util-linux 2.29.2
done.
[ ok ] Loading kernel modules...done.
[ ok ] Cleaning up temporary files... /tmp.
[ ok ] Mounting local filesystems...done.
[ ok ] Activating swapfile swap...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables...done.
[....] Configuring network interfaces...[ 40.468303] eth0: device MAC address 00:25:31:xx:xx:xx

Copyright 2004-2016 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Listening on LPF/eth0/00:25:31:01:c6:76
Sending on LPF/eth0/00:25:31:01:c6:76
Sending on Socket/fallback
DHCPREQUEST of 192.168.0.16 on eth0 to 255.255.255.255 port 67
DHCPREQUEST of 192.168.0.16 on eth0 to 255.255.255.255 port 67
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 11
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 18
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 14
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 10
No DHCPOFFERS received.
Trying recorded lease 192.168.0.16
PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data.

--- 192.168.0.1 ping statistics ---
1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms

No working leases in persistent database - sleeping.
done.
[ ok ] Starting RPC port mapper daemon: rpcbind.
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[ ok ] Starting NFS common utilities: statd idmapd.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1255 (syslogd)
. ok
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1254 (klogd)
. ok
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting system message bus: dbus.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.

Debian GNU/Linux 9 debian ttyS0
debian login:


;-)

I realize that I booted in Debian. My goal is to finalize this project by updating in such that:
- I can close everything in the original case (so it is safe again)
- Keep the serial connection for future recoveries
- Automatic booting &:
- No need for any bootable SATA harddisk
- No need for a USB stick
- Regular Pogoplug services running
- SSH root access to install additional software and to update the boot software in case this is usefull

Is this possible and if so, what are the next steps ?

myhobby,

> I realize that I booted in Debian.

But it did not boot into your USB rootfs. It booted into the kernel on your HDD! So you're not done, if that's what you meant to do as I suggested.


> My goal is to f
> inalize this project by updating in such that:
> - I can close everything in the original case (so
> it is safe again)
> - Keep the serial connection for future recoveries
> - Automatic booting &:
> - No need for any bootable SATA harddisk
> - No need for a USB stick
> - Regular Pogoplug services running
> - SSH root access to install additional software a
> nd to update the boot software in case this is use
> full
>
> Is this possible and if so, what are the next step
> s ?

It is simply not possible to do what you wanted to do above. Pogoplug services do not work as free anymore.

But if you like to run this box without SATA or USB, then you need to restore the stock FW in NAND (everything). And then boot into stock, enable SHH. And then use stock OS. The NAND space is simply too small to run the latest Debian rootfs.

However, if you run stock OS, I will not be interested in helping you :) I have provided a complete solution to run new u-boot and Debian for this box on USB or SATA:

https://forum.doozan.com/read.php?3,16017
https://forum.doozan.com/read.php?2,16044

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Ok,

Am I still able to run the pogoplug service with your u-boot and Debian for this box ?

myhobby,

> Am I still able to run the pogoplug service with
> your u-boot and Debian for this box ?

No, it will not be possible out of the box, without some more non-trivial setup.

I recall moonman at Arch site has this procedure working, and that procedure can be used on Debian too.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

To summarize this all. I installed U-boot on my device and now it is a working debian box booting from USB.

Tip for everyone in case you are working in different environments (Windows/Linux/OSx)

wget --no-check-certificate https://file.io/<your uploaded file> can save you an enormous amount of free time ;-)

Something I will never forget.

@bodhi: Thank you very much for helping. That was my reason to transform my pogo to U-boot. Pure respect ! ;-)

myhobby Wrote:
-------------------------------------------------------
> To summarize this all. I installed U-boot on my
> device and now it is a working debian box booting
> from USB.
>
> Tip for everyone in case you are working in
> different environments (Windows/Linux/OSx)
>
> wget --no-check-certificate https://file.io/<your
> uploaded file> can save you an enormous amount of
> free time ;-)
>
> Something I will never forget.
>
> @bodhi: Thank you very much for helping. That was
> my reason to transform my pogo to U-boot. Pure
> respect ! ;-)

Cool :) glad you got it working to your expectation!

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)