chad
NSA310 Installation Problems March 08, 2017 08:08PM |
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:59:20 -0700) ZyXEL NSA310 1-Bay Power Media Server SoC: Kirkwood 88F6281_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 PHY reset timed out MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 2040832 1bfa0115-01 83 loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** 3302440 bytes read in 623 ms (5.1 MiB/s) 7414190 bytes read in 1032 ms (6.9 MiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.10.0-kirkwood-tld-1 Created: 2017-03-09 1:48:04 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3302376 Bytes = 3.1 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.10.0-kirkwood-tld-1 Created: 2017-03-09 1:48:36 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7414126 Bytes = 7.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Error: unrecognized/unsupported machine ID (r1 = 0x00000fb6). Available machine support: ID (hex) NAME ffffffff Generic DT based system ffffffff Marvell Kirkwood (Flattened Device Tree) Please check your kernel config and/or bootloader.
NSA310> printenv arcNumber=4022 baudrate=115200 bootcmd=run bootcmd_uenv; run bootcmd_usb; usb stop; run bootcmd_sata; reset bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot bootdelay=10 console=ttyS0,115200 device=0:1 ethact=egiga0 ethaddr=b6:d0:5e:0f:a1:17 led_error=orange blinking led_exit=green off led_init=green blinking mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) partition=nand0,2 rootdelay=10 rootfstype=ext2 sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi sata_init=ide reset sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd sata_root=/dev/sda1 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=usb_rootfs rootdelay=10 $mtdparts $custom_params set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts stderr=serial stdin=serial stdout=serial uenv_import=echo importing envs ...; env import -t 0x810000 uenv_load=ide reset; setenv uenv_loaded 0; for devtype in ide; do for disknum in 0; do run uenv_read_disk; done; done uenv_loaded=0 uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x810000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if $devtype part $disknum; then run uenv_read; fi usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_init=usb start usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd usb_root=/dev/sda1
Re: NSA310 Installation Problems March 08, 2017 08:31PM |
Admin Registered: 13 years ago Posts: 18,548 |
Re: NSA310 Installation Problems March 08, 2017 08:40PM |
Admin Registered: 13 years ago Posts: 18,548 |
chad
Re: NSA310 Installation Problems March 08, 2017 08:49PM |
NSA310> printenv arcNumber=4022 baudrate=115200 bootcmd=run bootcmd_uenv; run bootcmd_usb; usb stop; run bootcmd_sata; reset bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot bootdelay=10 console=ttyS0,115200 device=0:1 dtb_file=/boot/dts/kirkwood-nsa310.dtb ethact=egiga0 ethaddr=b6:d0:5e:0f:a1:17 led_error=orange blinking led_exit=green off led_init=green blinking mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) partition=nand0,2 rootdelay=10 rootfstype=ext2 sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi sata_init=ide reset sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd sata_root=/dev/sda1 set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts stderr=serial stdin=serial stdout=serial uenv_import=echo importing envs ...; env import -t 0x810000 uenv_load=usb start; setenv uenv_loaded 0; for devtype in usb; do for disknum in 0; do run uenv_read_disk; done; done uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x810000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if $devtype part $disknum; then run uenv_read; fi usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_init=usb start usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd usb_root=/dev/sda1 Environment size: 2113/131068 bytes NSA310> boot
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Partition Map for USB device 0 -- Partition Type: DOS
Part Start Sector Num Sectors UUID Type
1 2048 2040832 1bfa0115-01 83
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **
3302440 bytes read in 622 ms (5.1 MiB/s)
7414190 bytes read in 1031 ms (6.9 MiB/s)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-4.10.0-kirkwood-tld-1
Created: 2017-03-09 1:48:04 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3302376 Bytes = 3.1 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-4.10.0-kirkwood-tld-1
Created: 2017-03-09 1:48:36 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 7414126 Bytes = 7.1 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Error: unrecognized/unsupported machine ID (r1 = 0x00000fb6).
Available machine support:
ID (hex) NAME
ffffffff Generic DT based system
ffffffff Marvell Kirkwood (Flattened Device Tree)
Please check your kernel config and/or bootloader.
Re: NSA310 Installation Problems March 08, 2017 11:14PM |
Admin Registered: 13 years ago Posts: 18,548 |
Quote
You need to adjust the env dtb_file to the DTB file name for NSA310.
setenv dtb_file '/boot/dts/kirkwood-nsa310.dtb'
chad
Re: NSA310 Installation Problems March 09, 2017 05:29PM |
Re: NSA310 Installation Problems March 09, 2017 07:24PM |
Admin Registered: 13 years ago Posts: 18,548 |
fw_setenv ethaddr xxxxxxx