Problem installing Netgear Stora
Posted by Erik
|
Problem installing Netgear Stora March 18, 2017 03:30AM |
Registered: 7 years ago Posts: 36 |
Hi Bodhi,
I have started with the instructions of installing new uboot.
- First i did unpack the env-tools - did look if kernel did support it
Did see this:
So i think fw_tools are supported with kernel 4.4.0 and higher.
Question: Does kernel 4.4.0 support envir-tools?
I ask this question becaus i get:
And i don know if its important; the name of mtd0 is not u-boot, but orion_nand:
Edited 1 time(s). Last edit at 03/18/2017 03:56AM by bodhi.
I have started with the instructions of installing new uboot.
- First i did unpack the env-tools - did look if kernel did support it
Did see this:
Updated 05 Sept 2015: Kernel linux-4.2.0-kirkwood-tld-1 package has been uploaded. The following features were updated/added: 1. Incorprate patched nsa3xx-hwmon module for NSA320 and NSA310 (some variant of). This patch allows these boxes to use the nsa3xx-hwmon like before (Device Tree transition in kernel 3.17 has broken this module). It also streams line the way NSA3xx hwmon is implemented in the kernel. 2. New Marvell CESA crypto driver is activated in this kernel. 3. Netgear Stora DTS was modified to correct NAND chip deday and enable write access to mtd0 (u-boot and u-boot envs).
So i think fw_tools are supported with kernel 4.4.0 and higher.
Question: Does kernel 4.4.0 support envir-tools?
I ask this question becaus i get:
root@debian:~# fw_printenv ethaddr [ 314.738491] __nand_correct_data: uncorrectable ECC error ... [ 317.216841] __nand_correct_data: uncorrectable ECC error Warning: Bad CRC, using default environment ## Error: "ethaddr" not defined root@debian:~#
And i don know if its important; the name of mtd0 is not u-boot, but orion_nand:
root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 10000000 00020000 "orion_nand"
Edited 1 time(s). Last edit at 03/18/2017 03:56AM by bodhi.
|
Re: Problem installing Netgear Stora March 18, 2017 03:59AM |
Admin Registered: 13 years ago Posts: 18,543 |
> So i think fw_tools are supported with kernel 4.4.
> 0 and higher.
> Question: Does kernel 4.4.0 support envir-tools?
Yes it does.
If you are not sure how to get through some error while instalingl u-boot, post the the entire log of what you did, and I will point out where the error is.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> 0 and higher.
> Question: Does kernel 4.4.0 support envir-tools?
Yes it does.
If you are not sure how to get through some error while instalingl u-boot, post the the entire log of what you did, and I will point out where the error is.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Problem installing Netgear Stora March 18, 2017 04:24AM |
Registered: 7 years ago Posts: 36 |
Hi Bodhi,
In the topic i added the putty.log, in which the commands and output is saved.
The only thing before i did, was:
download linux-tools-installation-bodhi.tar.gz
sha256sum
in /root:
tar xzvf linux-tools-installation-bodhi.tar.gz
cd tools
ln -s fw_printenv fw_setenv
cp -a fw_env.config /etc/
and cp -a the rest to /usr/sbin
cp -a busybox /usr/sbin
cp -a e2fsck /usr/sbin
cp -a nanddump /usr/sbin
cp -a fw_printenv /usr/sbin
cp -a flash_erase /usr/sbin
cp -a nandwrite /usr/sbin
thats all.
Then i started following this manual: 2016.05 U-Boot Kirkwood - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug, NSA325, NSA320, NSA310S, NSA320S, NSA310, HP T5325
here are the steps i did with the output (in the putty logfile on the previous post is the compleet output from startup)
In the topic i added the putty.log, in which the commands and output is saved.
The only thing before i did, was:
download linux-tools-installation-bodhi.tar.gz
sha256sum
in /root:
tar xzvf linux-tools-installation-bodhi.tar.gz
cd tools
ln -s fw_printenv fw_setenv
cp -a fw_env.config /etc/
and cp -a the rest to /usr/sbin
cp -a busybox /usr/sbin
cp -a e2fsck /usr/sbin
cp -a nanddump /usr/sbin
cp -a fw_printenv /usr/sbin
cp -a flash_erase /usr/sbin
cp -a nandwrite /usr/sbin
thats all.
Then i started following this manual: 2016.05 U-Boot Kirkwood - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug, NSA325, NSA320, NSA310S, NSA320S, NSA310, HP T5325
here are the steps i did with the output (in the putty logfile on the previous post is the compleet output from startup)
root@debian:~# cat /etc/fw_env.config # Configuration file for fw_(printenv/saveenv) utility. # Up to two entries are valid, in this case the redundant # environment sector is assumed present. # Notice, that the "Number of sectors" is ignored on NOR. # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd0 0xc0000 0x20000 0x20000 root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 10000000 00020000 "orion_nand" root@debian:~# fw_printenv ethaddr [ 314.738491] __nand_correct_data: uncorrectable ECC error [ 314.743919] __nand_correct_data: uncorrectable ECC error [ 314.749292] __nand_correct_data: uncorrectable ECC error [ 314.755149] __nand_correct_data: uncorrectable ECC error [ 314.760526] __nand_correct_data: uncorrectable ECC error [ 314.766200] __nand_correct_data: uncorrectable ECC error [ 314.771556] __nand_correct_data: uncorrectable ECC error [ 314.777618] __nand_correct_data: uncorrectable ECC error [ 314.782954] __nand_correct_data: uncorrectable ECC error [ 314.788596] __nand_correct_data: uncorrectable ECC error [ 314.793960] __nand_correct_data: uncorrectable ECC error [ 314.799296] __nand_correct_data: uncorrectable ECC error [ 314.805005] __nand_correct_data: uncorrectable ECC error [ 314.810344] __nand_correct_data: uncorrectable ECC error [ 314.816394] __nand_correct_data: uncorrectable ECC error [ 314.821732] __nand_correct_data: uncorrectable ECC error [ 314.827368] __nand_correct_data: uncorrectable ECC error [ 314.832703] __nand_correct_data: uncorrectable ECC error [ 314.838335] __nand_correct_data: uncorrectable ECC error [ 314.843671] __nand_correct_data: uncorrectable ECC error [ 314.849304] __nand_correct_data: uncorrectable ECC error [ 314.855087] __nand_correct_data: uncorrectable ECC error [ 314.860423] __nand_correct_data: uncorrectable ECC error [ 314.866127] __nand_correct_data: uncorrectable ECC error [ 314.871463] __nand_correct_data: uncorrectable ECC error [ 314.877095] __nand_correct_data: uncorrectable ECC error [ 314.882432] __nand_correct_data: uncorrectable ECC error [ 314.888064] __nand_correct_data: uncorrectable ECC error [ 314.894036] __nand_correct_data: uncorrectable ECC error [ 314.899375] __nand_correct_data: uncorrectable ECC error [ 314.905016] __nand_correct_data: uncorrectable ECC error [ 314.910354] __nand_correct_data: uncorrectable ECC error [ 314.915987] __nand_correct_data: uncorrectable ECC error [ 314.921323] __nand_correct_data: uncorrectable ECC error [ 314.926955] __nand_correct_data: uncorrectable ECC error [ 314.932712] __nand_correct_data: uncorrectable ECC error [ 314.938451] __nand_correct_data: uncorrectable ECC error [ 314.943890] __nand_correct_data: uncorrectable ECC error [ 314.949317] __nand_correct_data: uncorrectable ECC error [ 314.955081] __nand_correct_data: uncorrectable ECC error [ 314.960425] __nand_correct_data: uncorrectable ECC error [ 314.966086] __nand_correct_data: uncorrectable ECC error [ 314.971847] __nand_correct_data: uncorrectable ECC error [ 314.977496] __nand_correct_data: uncorrectable ECC error [ 314.982850] __nand_correct_data: uncorrectable ECC error [ 314.988480] __nand_correct_data: uncorrectable ECC error [ 314.993850] __nand_correct_data: uncorrectable ECC error [ 314.999184] __nand_correct_data: uncorrectable ECC error [ 315.004890] __nand_correct_data: uncorrectable ECC error [ 315.010652] __nand_correct_data: uncorrectable ECC error [ 315.016288] __nand_correct_data: uncorrectable ECC error [ 315.021630] __nand_correct_data: uncorrectable ECC error [ 315.027264] __nand_correct_data: uncorrectable ECC error [ 315.032599] __nand_correct_data: uncorrectable ECC error [ 315.038230] __nand_correct_data: uncorrectable ECC error [ 315.043583] __nand_correct_data: uncorrectable ECC error [ 315.049625] __nand_correct_data: uncorrectable ECC error [ 315.054994] __nand_correct_data: uncorrectable ECC error [ 315.060329] __nand_correct_data: uncorrectable ECC error [ 315.066031] __nand_correct_data: uncorrectable ECC error [ 315.071368] __nand_correct_data: uncorrectable ECC error [ 315.076999] __nand_correct_data: uncorrectable ECC error [ 315.082339] __nand_correct_data: uncorrectable ECC error [ 315.088397] __nand_correct_data: uncorrectable ECC error [ 315.093735] __nand_correct_data: uncorrectable ECC error [ 315.099368] __nand_correct_data: uncorrectable ECC error [ 315.104732] __nand_correct_data: uncorrectable ECC error [ 315.110068] __nand_correct_data: uncorrectable ECC error [ 315.115774] __nand_correct_data: uncorrectable ECC error [ 315.121116] __nand_correct_data: uncorrectable ECC error [ 315.127167] __nand_correct_data: uncorrectable ECC error [ 315.132504] __nand_correct_data: uncorrectable ECC error [ 315.138141] __nand_correct_data: uncorrectable ECC error [ 315.143483] __nand_correct_data: uncorrectable ECC error [ 315.149115] __nand_correct_data: uncorrectable ECC error [ 315.154484] __nand_correct_data: uncorrectable ECC error [ 315.159824] __nand_correct_data: uncorrectable ECC error [ 315.165952] __nand_correct_data: uncorrectable ECC error [ 315.171292] __nand_correct_data: uncorrectable ECC error [ 315.176925] __nand_correct_data: uncorrectable ECC error [ 315.182261] __nand_correct_data: uncorrectable ECC error [ 315.187893] __nand_correct_data: uncorrectable ECC error [ 315.193231] __nand_correct_data: uncorrectable ECC error [ 315.198920] __nand_correct_data: uncorrectable ECC error [ 315.204814] __nand_correct_data: uncorrectable ECC error [ 315.210156] __nand_correct_data: uncorrectable ECC error [ 315.215866] __nand_correct_data: uncorrectable ECC error [ 315.221205] __nand_correct_data: uncorrectable ECC error [ 315.226841] __nand_correct_data: uncorrectable ECC error [ 315.232182] __nand_correct_data: uncorrectable ECC error [ 315.237815] __nand_correct_data: uncorrectable ECC error [ 315.243570] __nand_correct_data: uncorrectable ECC error [ 315.249208] __nand_correct_data: uncorrectable ECC error [ 315.254575] __nand_correct_data: uncorrectable ECC error [ 315.259912] __nand_correct_data: uncorrectable ECC error [ 315.265614] __nand_correct_data: uncorrectable ECC error [ 315.270952] __nand_correct_data: uncorrectable ECC error [ 315.276583] __nand_correct_data: uncorrectable ECC error [ 315.282340] __nand_correct_data: uncorrectable ECC error [ 315.287977] __nand_correct_data: uncorrectable ECC error [ 315.293318] __nand_correct_data: uncorrectable ECC error [ 315.298951] __nand_correct_data: uncorrectable ECC error [ 315.304315] __nand_correct_data: uncorrectable ECC error [ 315.309651] __nand_correct_data: uncorrectable ECC error [ 315.315357] __nand_correct_data: uncorrectable ECC error [ 315.321118] __nand_correct_data: uncorrectable ECC error [ 315.326751] __nand_correct_data: uncorrectable ECC error [ 315.332088] __nand_correct_data: uncorrectable ECC error [ 315.337722] __nand_correct_data: uncorrectable ECC error [ 315.343058] __nand_correct_data: uncorrectable ECC error [ 315.348690] __nand_correct_data: uncorrectable ECC error [ 315.354053] __nand_correct_data: uncorrectable ECC error [ 315.359808] __nand_correct_data: uncorrectable ECC error [ 315.365517] __nand_correct_data: uncorrectable ECC error [ 315.370857] __nand_correct_data: uncorrectable ECC error [ 315.376489] __nand_correct_data: uncorrectable ECC error [ 315.381826] __nand_correct_data: uncorrectable ECC error [ 315.387457] __nand_correct_data: uncorrectable ECC error [ 315.392797] __nand_correct_data: uncorrectable ECC error [ 315.398859] __nand_correct_data: uncorrectable ECC error [ 315.404229] __nand_correct_data: uncorrectable ECC error [ 315.409565] __nand_correct_data: uncorrectable ECC error [ 315.415268] __nand_correct_data: uncorrectable ECC error [ 315.420605] __nand_correct_data: uncorrectable ECC error [ 315.426243] __nand_correct_data: uncorrectable ECC error [ 315.431583] __nand_correct_data: uncorrectable ECC error [ 315.437632] __nand_correct_data: uncorrectable ECC error [ 315.442972] __nand_correct_data: uncorrectable ECC error [ 315.448718] __nand_correct_data: uncorrectable ECC error [ 315.454085] __nand_correct_data: uncorrectable ECC error [ 315.459417] __nand_correct_data: uncorrectable ECC error [ 315.465131] __nand_correct_data: uncorrectable ECC error [ 315.470475] __nand_correct_data: uncorrectable ECC error [ 315.476531] __nand_correct_data: uncorrectable ECC error [ 315.481871] __nand_correct_data: uncorrectable ECC error [ 315.487509] __nand_correct_data: uncorrectable ECC error [ 315.492850] __nand_correct_data: uncorrectable ECC error [ 315.498482] __nand_correct_data: uncorrectable ECC error [ 315.503846] __nand_correct_data: uncorrectable ECC error [ 315.509182] __nand_correct_data: uncorrectable ECC error [ 315.515307] __nand_correct_data: uncorrectable ECC error [ 315.520649] __nand_correct_data: uncorrectable ECC error [ 315.526282] __nand_correct_data: uncorrectable ECC error [ 315.531619] __nand_correct_data: uncorrectable ECC error [ 315.537253] __nand_correct_data: uncorrectable ECC error [ 315.542589] __nand_correct_data: uncorrectable ECC error [ 315.548219] __nand_correct_data: uncorrectable ECC error [ 315.554191] __nand_correct_data: uncorrectable ECC error [ 315.559532] __nand_correct_data: uncorrectable ECC error [ 315.565164] __nand_correct_data: uncorrectable ECC error [ 315.570502] __nand_correct_data: uncorrectable ECC error [ 315.576133] __nand_correct_data: uncorrectable ECC error [ 315.581471] __nand_correct_data: uncorrectable ECC error [ 315.587103] __nand_correct_data: uncorrectable ECC error [ 315.592860] __nand_correct_data: uncorrectable ECC error [ 315.598493] __nand_correct_data: uncorrectable ECC error [ 315.603856] __nand_correct_data: uncorrectable ECC error [ 315.609192] __nand_correct_data: uncorrectable ECC error [ 315.614894] __nand_correct_data: uncorrectable ECC error [ 315.620232] __nand_correct_data: uncorrectable ECC error [ 315.625864] __nand_correct_data: uncorrectable ECC error [ 315.631620] __nand_correct_data: uncorrectable ECC error [ 315.637254] __nand_correct_data: uncorrectable ECC error [ 315.642590] __nand_correct_data: uncorrectable ECC error [ 315.648223] __nand_correct_data: uncorrectable ECC error [ 315.653559] __nand_correct_data: uncorrectable ECC error [ 315.659190] __nand_correct_data: uncorrectable ECC error [ 315.664556] __nand_correct_data: uncorrectable ECC error [ 315.670309] __nand_correct_data: uncorrectable ECC error [ 315.676020] __nand_correct_data: uncorrectable ECC error [ 315.681359] __nand_correct_data: uncorrectable ECC error [ 315.686991] __nand_correct_data: uncorrectable ECC error [ 315.692328] __nand_correct_data: uncorrectable ECC error [ 315.697960] __nand_correct_data: uncorrectable ECC error [ 315.703298] __nand_correct_data: uncorrectable ECC error [ 315.709349] __nand_correct_data: uncorrectable ECC error [ 315.714714] __nand_correct_data: uncorrectable ECC error [ 315.720049] __nand_correct_data: uncorrectable ECC error [ 315.725752] __nand_correct_data: uncorrectable ECC error [ 315.731089] __nand_correct_data: uncorrectable ECC error [ 315.736723] __nand_correct_data: uncorrectable ECC error [ 315.742058] __nand_correct_data: uncorrectable ECC error [ 315.748107] __nand_correct_data: uncorrectable ECC error [ 315.753447] __nand_correct_data: uncorrectable ECC error [ 315.759081] __nand_correct_data: uncorrectable ECC error [ 315.764443] __nand_correct_data: uncorrectable ECC error [ 315.769779] __nand_correct_data: uncorrectable ECC error [ 315.775479] __nand_correct_data: uncorrectable ECC error [ 315.780820] __nand_correct_data: uncorrectable ECC error [ 315.786868] __nand_correct_data: uncorrectable ECC error [ 315.792208] __nand_correct_data: uncorrectable ECC error [ 315.797841] __nand_correct_data: uncorrectable ECC error [ 315.803177] __nand_correct_data: uncorrectable ECC error [ 315.808809] __nand_correct_data: uncorrectable ECC error [ 315.814174] __nand_correct_data: uncorrectable ECC error [ 315.819510] __nand_correct_data: uncorrectable ECC error [ 315.825635] __nand_correct_data: uncorrectable ECC error [ 315.830977] __nand_correct_data: uncorrectable ECC error [ 315.836608] __nand_correct_data: uncorrectable ECC error [ 315.841946] __nand_correct_data: uncorrectable ECC error [ 315.847579] __nand_correct_data: uncorrectable ECC error [ 315.852916] __nand_correct_data: uncorrectable ECC error [ 315.858547] __nand_correct_data: uncorrectable ECC error [ 315.864331] __nand_correct_data: uncorrectable ECC error [ 315.869667] __nand_correct_data: uncorrectable ECC error [ 315.875377] __nand_correct_data: uncorrectable ECC error [ 315.880715] __nand_correct_data: uncorrectable ECC error [ 315.886350] __nand_correct_data: uncorrectable ECC error [ 315.891685] __nand_correct_data: uncorrectable ECC error [ 315.897316] __nand_correct_data: uncorrectable ECC error [ 315.903074] __nand_correct_data: uncorrectable ECC error [ 315.908709] __nand_correct_data: uncorrectable ECC error [ 315.914071] __nand_correct_data: uncorrectable ECC error [ 315.919405] __nand_correct_data: uncorrectable ECC error [ 315.925106] __nand_correct_data: uncorrectable ECC error [ 315.930445] __nand_correct_data: uncorrectable ECC error [ 315.936079] __nand_correct_data: uncorrectable ECC error [ 315.941834] __nand_correct_data: uncorrectable ECC error [ 315.947468] __nand_correct_data: uncorrectable ECC error [ 315.952804] __nand_correct_data: uncorrectable ECC error [ 315.958438] __nand_correct_data: uncorrectable ECC error [ 315.963773] __nand_correct_data: uncorrectable ECC error [ 315.969403] __nand_correct_data: uncorrectable ECC error [ 315.974770] __nand_correct_data: uncorrectable ECC error [ 315.980524] __nand_correct_data: uncorrectable ECC error [ 315.986233] __nand_correct_data: uncorrectable ECC error [ 315.991572] __nand_correct_data: uncorrectable ECC error [ 315.997206] __nand_correct_data: uncorrectable ECC error [ 316.002543] __nand_correct_data: uncorrectable ECC error [ 316.008316] __nand_correct_data: uncorrectable ECC error [ 316.013661] __nand_correct_data: uncorrectable ECC error [ 316.019726] __nand_correct_data: uncorrectable ECC error [ 316.025095] __nand_correct_data: uncorrectable ECC error [ 316.030428] __nand_correct_data: uncorrectable ECC error [ 316.036139] __nand_correct_data: uncorrectable ECC error [ 316.041477] __nand_correct_data: uncorrectable ECC error [ 316.047111] __nand_correct_data: uncorrectable ECC error [ 316.052446] __nand_correct_data: uncorrectable ECC error [ 316.058496] __nand_correct_data: uncorrectable ECC error [ 316.063863] __nand_correct_data: uncorrectable ECC error [ 316.069197] __nand_correct_data: uncorrectable ECC error [ 316.074908] __nand_correct_data: uncorrectable ECC error [ 316.080246] __nand_correct_data: uncorrectable ECC error [ 316.085879] __nand_correct_data: uncorrectable ECC error [ 316.091216] __nand_correct_data: uncorrectable ECC error [ 316.097289] __nand_correct_data: uncorrectable ECC error [ 316.102631] __nand_correct_data: uncorrectable ECC error [ 316.108267] __nand_correct_data: uncorrectable ECC error [ 316.113608] __nand_correct_data: uncorrectable ECC error [ 316.119241] __nand_correct_data: uncorrectable ECC error [ 316.124605] __nand_correct_data: uncorrectable ECC error [ 316.129942] __nand_correct_data: uncorrectable ECC error [ 316.136066] __nand_correct_data: uncorrectable ECC error [ 316.141408] __nand_correct_data: uncorrectable ECC error [ 316.147042] __nand_correct_data: uncorrectable ECC error [ 316.152378] __nand_correct_data: uncorrectable ECC error [ 316.158012] __nand_correct_data: uncorrectable ECC error [ 316.163348] __nand_correct_data: uncorrectable ECC error [ 316.168978] __nand_correct_data: uncorrectable ECC error [ 316.174763] __nand_correct_data: uncorrectable ECC error [ 316.180098] __nand_correct_data: uncorrectable ECC error [ 316.185808] __nand_correct_data: uncorrectable ECC error [ 316.191147] __nand_correct_data: uncorrectable ECC error [ 316.196779] __nand_correct_data: uncorrectable ECC error [ 316.202117] __nand_correct_data: uncorrectable ECC error [ 316.207797] __nand_correct_data: uncorrectable ECC error [ 316.213668] __nand_correct_data: uncorrectable ECC error [ 316.219308] __nand_correct_data: uncorrectable ECC error [ 316.224676] __nand_correct_data: uncorrectable ECC error [ 316.230013] __nand_correct_data: uncorrectable ECC error [ 316.235713] __nand_correct_data: uncorrectable ECC error [ 316.241052] __nand_correct_data: uncorrectable ECC error [ 316.246683] __nand_correct_data: uncorrectable ECC error [ 316.252441] __nand_correct_data: uncorrectable ECC error [ 316.258075] __nand_correct_data: uncorrectable ECC error [ 316.263410] __nand_correct_data: uncorrectable ECC error [ 316.269043] __nand_correct_data: uncorrectable ECC error [ 316.274406] __nand_correct_data: uncorrectable ECC error [ 316.279742] __nand_correct_data: uncorrectable ECC error [ 316.285444] __nand_correct_data: uncorrectable ECC error [ 316.291200] __nand_correct_data: uncorrectable ECC error [ 316.296835] __nand_correct_data: uncorrectable ECC error [ 316.302170] __nand_correct_data: uncorrectable ECC error [ 316.307803] __nand_correct_data: uncorrectable ECC error [ 316.313140] __nand_correct_data: uncorrectable ECC error [ 316.318771] __nand_correct_data: uncorrectable ECC error [ 316.324136] __nand_correct_data: uncorrectable ECC error [ 316.329891] __nand_correct_data: uncorrectable ECC error [ 316.335600] __nand_correct_data: uncorrectable ECC error [ 316.340940] __nand_correct_data: uncorrectable ECC error [ 316.346577] __nand_correct_data: uncorrectable ECC error [ 316.351918] __nand_correct_data: uncorrectable ECC error [ 316.357550] __nand_correct_data: uncorrectable ECC error [ 316.362887] __nand_correct_data: uncorrectable ECC error [ 316.368936] __nand_correct_data: uncorrectable ECC error [ 316.374304] __nand_correct_data: uncorrectable ECC error [ 316.379638] __nand_correct_data: uncorrectable ECC error [ 316.385347] __nand_correct_data: uncorrectable ECC error [ 316.390687] __nand_correct_data: uncorrectable ECC error [ 316.396320] __nand_correct_data: uncorrectable ECC error [ 316.401656] __nand_correct_data: uncorrectable ECC error [ 316.407708] __nand_correct_data: uncorrectable ECC error [ 316.413046] __nand_correct_data: uncorrectable ECC error [ 316.418685] __nand_correct_data: uncorrectable ECC error [ 316.424051] __nand_correct_data: uncorrectable ECC error [ 316.429386] __nand_correct_data: uncorrectable ECC error [ 316.435086] __nand_correct_data: uncorrectable ECC error [ 316.440426] __nand_correct_data: uncorrectable ECC error [ 316.446475] __nand_correct_data: uncorrectable ECC error [ 316.451815] __nand_correct_data: uncorrectable ECC error [ 316.457448] __nand_correct_data: uncorrectable ECC error [ 316.462784] __nand_correct_data: uncorrectable ECC error [ 316.468417] __nand_correct_data: uncorrectable ECC error [ 316.473754] __nand_correct_data: uncorrectable ECC error [ 316.479385] __nand_correct_data: uncorrectable ECC error [ 316.485168] __nand_correct_data: uncorrectable ECC error [ 316.490504] __nand_correct_data: uncorrectable ECC error [ 316.496215] __nand_correct_data: uncorrectable ECC error [ 316.501554] __nand_correct_data: uncorrectable ECC error [ 316.507187] __nand_correct_data: uncorrectable ECC error [ 316.512523] __nand_correct_data: uncorrectable ECC error [ 316.518154] __nand_correct_data: uncorrectable ECC error [ 316.524124] __nand_correct_data: uncorrectable ECC error [ 316.529466] __nand_correct_data: uncorrectable ECC error [ 316.535100] __nand_correct_data: uncorrectable ECC error [ 316.540436] __nand_correct_data: uncorrectable ECC error [ 316.546067] __nand_correct_data: uncorrectable ECC error [ 316.551405] __nand_correct_data: uncorrectable ECC error [ 316.557037] __nand_correct_data: uncorrectable ECC error [ 316.562793] __nand_correct_data: uncorrectable ECC error [ 316.568425] __nand_correct_data: uncorrectable ECC error [ 316.573763] __nand_correct_data: uncorrectable ECC error [ 316.579395] __nand_correct_data: uncorrectable ECC error [ 316.584760] __nand_correct_data: uncorrectable ECC error [ 316.590095] __nand_correct_data: uncorrectable ECC error [ 316.595797] __nand_correct_data: uncorrectable ECC error [ 316.601554] __nand_correct_data: uncorrectable ECC error [ 316.607187] __nand_correct_data: uncorrectable ECC error [ 316.612524] __nand_correct_data: uncorrectable ECC error [ 316.618164] __nand_correct_data: uncorrectable ECC error [ 316.623502] __nand_correct_data: uncorrectable ECC error [ 316.629134] __nand_correct_data: uncorrectable ECC error [ 316.634504] __nand_correct_data: uncorrectable ECC error [ 316.640262] __nand_correct_data: uncorrectable ECC error [ 316.645975] __nand_correct_data: uncorrectable ECC error [ 316.651310] __nand_correct_data: uncorrectable ECC error [ 316.656941] __nand_correct_data: uncorrectable ECC error [ 316.662280] __nand_correct_data: uncorrectable ECC error [ 316.667913] __nand_correct_data: uncorrectable ECC error [ 316.673249] __nand_correct_data: uncorrectable ECC error [ 316.679299] __nand_correct_data: uncorrectable ECC error [ 316.684666] __nand_correct_data: uncorrectable ECC error [ 316.690000] __nand_correct_data: uncorrectable ECC error [ 316.695711] __nand_correct_data: uncorrectable ECC error [ 316.701049] __nand_correct_data: uncorrectable ECC error [ 316.706688] __nand_correct_data: uncorrectable ECC error [ 316.712027] __nand_correct_data: uncorrectable ECC error [ 316.718078] __nand_correct_data: uncorrectable ECC error [ 316.723416] __nand_correct_data: uncorrectable ECC error [ 316.729052] __nand_correct_data: uncorrectable ECC error [ 316.734422] __nand_correct_data: uncorrectable ECC error [ 316.739756] __nand_correct_data: uncorrectable ECC error [ 316.745457] __nand_correct_data: uncorrectable ECC error [ 316.750797] __nand_correct_data: uncorrectable ECC error [ 316.756849] __nand_correct_data: uncorrectable ECC error [ 316.762185] __nand_correct_data: uncorrectable ECC error [ 316.767819] __nand_correct_data: uncorrectable ECC error [ 316.773155] __nand_correct_data: uncorrectable ECC error [ 316.778794] __nand_correct_data: uncorrectable ECC error [ 316.784160] __nand_correct_data: uncorrectable ECC error [ 316.789496] __nand_correct_data: uncorrectable ECC error [ 316.795616] __nand_correct_data: uncorrectable ECC error [ 316.800955] __nand_correct_data: uncorrectable ECC error [ 316.806587] __nand_correct_data: uncorrectable ECC error [ 316.811925] __nand_correct_data: uncorrectable ECC error [ 316.817558] __nand_correct_data: uncorrectable ECC error [ 316.822894] __nand_correct_data: uncorrectable ECC error [ 316.828525] __nand_correct_data: uncorrectable ECC error [ 316.834309] __nand_correct_data: uncorrectable ECC error [ 316.839645] __nand_correct_data: uncorrectable ECC error [ 316.845354] __nand_correct_data: uncorrectable ECC error [ 316.850693] __nand_correct_data: uncorrectable ECC error [ 316.856326] __nand_correct_data: uncorrectable ECC error [ 316.861663] __nand_correct_data: uncorrectable ECC error [ 316.867294] __nand_correct_data: uncorrectable ECC error [ 316.873052] __nand_correct_data: uncorrectable ECC error [ 316.878684] __nand_correct_data: uncorrectable ECC error [ 316.884047] __nand_correct_data: uncorrectable ECC error [ 316.889383] __nand_correct_data: uncorrectable ECC error [ 316.895090] __nand_correct_data: uncorrectable ECC error [ 316.900432] __nand_correct_data: uncorrectable ECC error [ 316.906065] __nand_correct_data: uncorrectable ECC error [ 316.911820] __nand_correct_data: uncorrectable ECC error [ 316.917456] __nand_correct_data: uncorrectable ECC error [ 316.922799] __nand_correct_data: uncorrectable ECC error [ 316.928432] __nand_correct_data: uncorrectable ECC error [ 316.933769] __nand_correct_data: uncorrectable ECC error [ 316.939400] __nand_correct_data: uncorrectable ECC error [ 316.944873] __nand_correct_data: uncorrectable ECC error [ 316.950777] __nand_correct_data: uncorrectable ECC error [ 316.956531] __nand_correct_data: uncorrectable ECC error [ 316.961906] __nand_correct_data: uncorrectable ECC error [ 316.967546] __nand_correct_data: uncorrectable ECC error [ 316.972916] __nand_correct_data: uncorrectable ECC error [ 316.978547] __nand_correct_data: uncorrectable ECC error [ 316.983912] __nand_correct_data: uncorrectable ECC error [ 316.989675] __nand_correct_data: uncorrectable ECC error [ 316.995382] __nand_correct_data: uncorrectable ECC error [ 317.000720] __nand_correct_data: uncorrectable ECC error [ 317.006359] __nand_correct_data: uncorrectable ECC error [ 317.011699] __nand_correct_data: uncorrectable ECC error [ 317.017333] __nand_correct_data: uncorrectable ECC error [ 317.022669] __nand_correct_data: uncorrectable ECC error [ 317.028719] __nand_correct_data: uncorrectable ECC error [ 317.034084] __nand_correct_data: uncorrectable ECC error [ 317.039420] __nand_correct_data: uncorrectable ECC error [ 317.045129] __nand_correct_data: uncorrectable ECC error [ 317.050483] __nand_correct_data: uncorrectable ECC error [ 317.056106] __nand_correct_data: uncorrectable ECC error [ 317.061447] __nand_correct_data: uncorrectable ECC error [ 317.067499] __nand_correct_data: uncorrectable ECC error [ 317.072835] __nand_correct_data: uncorrectable ECC error [ 317.078470] __nand_correct_data: uncorrectable ECC error [ 317.083805] __nand_correct_data: uncorrectable ECC error [ 317.089440] __nand_correct_data: uncorrectable ECC error [ 317.094801] __nand_correct_data: uncorrectable ECC error [ 317.100137] __nand_correct_data: uncorrectable ECC error [ 317.106256] __nand_correct_data: uncorrectable ECC error [ 317.111596] __nand_correct_data: uncorrectable ECC error [ 317.117229] __nand_correct_data: uncorrectable ECC error [ 317.122565] __nand_correct_data: uncorrectable ECC error [ 317.128199] __nand_correct_data: uncorrectable ECC error [ 317.133535] __nand_correct_data: uncorrectable ECC error [ 317.139165] __nand_correct_data: uncorrectable ECC error [ 317.144950] __nand_correct_data: uncorrectable ECC error [ 317.150285] __nand_correct_data: uncorrectable ECC error [ 317.156003] __nand_correct_data: uncorrectable ECC error [ 317.161343] __nand_correct_data: uncorrectable ECC error [ 317.166976] __nand_correct_data: uncorrectable ECC error [ 317.172313] __nand_correct_data: uncorrectable ECC error [ 317.177946] __nand_correct_data: uncorrectable ECC error [ 317.183702] __nand_correct_data: uncorrectable ECC error [ 317.189336] __nand_correct_data: uncorrectable ECC error [ 317.194697] __nand_correct_data: uncorrectable ECC error [ 317.200033] __nand_correct_data: uncorrectable ECC error [ 317.205794] __nand_correct_data: uncorrectable ECC error [ 317.211165] __nand_correct_data: uncorrectable ECC error [ 317.216841] __nand_correct_data: uncorrectable ECC error Warning: Bad CRC, using default environment ## Error: "ethaddr" not defined root@debian:~#
|
Re: Problem installing Netgear Stora March 18, 2017 04:38AM |
Registered: 7 years ago Posts: 36 |
Hi Bodhi,
Maybe important, i did some time ago a resetenv.
Because of this i had to startup and load the flashware.img file.
I did follow this topic: http://www.openstora.com/forum/viewtopic.php?f=6&t=412&sid=0ec63b563241250366be7c45ed063b61&start=15
A few days ago, i had to flash it again, because i did get crc errors - i think from repeatly unpower after bad boot.
I added the file.
Maybe important, i did some time ago a resetenv.
Because of this i had to startup and load the flashware.img file.
I did follow this topic: http://www.openstora.com/forum/viewtopic.php?f=6&t=412&sid=0ec63b563241250366be7c45ed063b61&start=15
1. Apparently u-boot try to load the file "flashware.img" from a usb-stick very early in the booting procedure. I downloaded this file http://www.openstora.com/files/displayimage.php?pid=50, which is a working u-boot partition, uncompressed it, renamed "u-boot.mtd0" to "flashware.img", and loaded it onto a clean usb-stick formatted with ext2. 2. With the usb-stick in the Stora and working serial connection, I started the Stora. It boots as usual but somewhere in the middle you should see something like: Code: Select all USB: scanning bus for devices... 2 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Trying to load image from USB flash drive using FAT FS reading /flashware.img ** Unable to read "/flashware.img" from usb 0:1 ** Trying to load image from USB flash drive using ext2 FS partition 0 Failed to mount ext2 filesystem... ** Bad ext2 partition or disk - usb 0:0 ** Trying to load image from USB flash drive using ext2 FS partition 1 . ......................... ......................... ......................... ........................ 1048576 bytes read I.e. it found the usb and have loaded "flashware.img" to memory (address 0x0). Ok, so we have a working u-boot image loaded into memory so the hard part is done. The boot sequence continues as usual (thus ignores the loaded image) and one comes to: Code: Select all ## Booting image at 00800000 ... Bad Magic Number Marvell>> 3. First we need to check that the image is loaded correctly. Run "crc32 0x0 0x100000" (this assumes that you use the exact file above, "0x100000" should be changed according to the real filesize). You should see: Code: Select all Marvell>> crc32 0x0 0x100000 CRC32 for 00000000 ... 000fffff ==> ec37629d "ec37629d" is what I got, you should check this by running CRC32 on your desktop on the downloaded file ("crc32 u-boot.mtd0"). If the checksums do not match, DO NOT continue! 4. Now lets load the image to the NAND. We would like to minimize the risk of bricking the Stora for real so we will only load the bare minimum needed. Apparently the only problem is that the enviroment variables are all messed up, the u-boot code are all fine. So we will only take the enviroment variables from the image loaded in memory. The enviroment variables starts at 0xA0000. I don't know how big the variable-part is, but it should be in the end of the code so we'll take everything to the end of the image (total size is 0x100000, we start at 0xA0000 => size to load is 0x60000). First run "nand erase 0xA0000 0x60000" and then "nand write 0xA0000 0xA0000 0x60000". You should see: Code: Select all Marvell>> nand erase 0xA0000 0x60000 NAND erase: device 0 offset 0xa0000, size 0x60000 Erasing at 0xe0000 -- 100% complete. OK Marvell>> nand write 0xA0000 0xA0000 0x60000 NAND write: device 0 offset 0xa0000, size 0x60000 393216 bytes written: OK Now everything should be ok, so we run "reset" and the Stora should boot up fully functional! Don't forget to change "ethaddr" to something else.
A few days ago, i had to flash it again, because i did get crc errors - i think from repeatly unpower after bad boot.
I added the file.
|
Re: Problem installing Netgear Stora March 18, 2017 08:42AM |
Registered: 7 years ago Posts: 36 |
Hi Bodhi,
I found:
http://forum.doozan.com/read.php?2,29259,29285,quote=1
And this, looking at the original boot:
And did this:
Output:
with original firmware:
I still have that error:
I found:
http://forum.doozan.com/read.php?2,29259,29285,quote=1
And this, looking at the original boot:
... Using static partition definition Creating 3 MTD partitions on "nand_mtd": 0x00000000-0x00100000 : "u-boot" 0x00100000-0x00700000 : "uImage" 0x00700000-0x10000000 : "root" ..
And did this:
setenv console 'console=ttyS0,115200 mtdparts=orion_nand:0x100000@0(uboot),0xff00000@0x100000(root)' saveenv
Output:
root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 00100000 00020000 "uboot" mtd1: 0ff00000 00020000 "root"
with original firmware:
-bash-3.2# cat /proc/mtd dev: size erasesize name mtd0: 00100000 00020000 "u-boot" mtd1: 00600000 00020000 "uImage" mtd2: 0f900000 00020000 "root" -bash-3.2#
I still have that error:
__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** MARVELL BOARD: RD-88F6281A LE U-Boot 1.1.4 (Sep 4 2009 - 09:36:11) Marvell version: 3.4.14 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CEE60 Soc: 88F6281 A0 (DDR2) CPU running @ 1000Mhz L2 running @ 333Mhz SysClock = 333Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 64MB DRAM CS[1] base 0x04000000 size 64MB DRAM Total size 128MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:256 MB CRC in Flash: 70c3cb0f, Calculated CRC: 70c3cb0f CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled Module 0 is RGMII Module 1 is TDM USB 0: host mode PEX 0: interface detected no Link. Net: egiga0, egiga1 [PRIME] Hit any key to stop autoboot: 0 Marvell>> Marvell>> Marvell>> printenv console console=console=ttyS0,115200 mtdparts=orion_nand:0x100000@0(uboot),0xff00000@0x100000(root) Marvell>> run usb_bootcmd (Re)start USB... USB: scanning bus for devices... 2 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found .... . ...... ............ ......................... ................................................... ...................................................................................................... ........................................................................................................ 3166745 bytes read .... . ...... ............ ......................... ................................................... ...................................................................................................... ................................................................................................................................................................................................................. .............................................................................................................................................................................................................................................................................................. 7179935 bytes read ## Booting image at 00800000 ... Image Name: Linux-4.4.0-kirkwood-tld-1 Created: 2017-03-16 18:54:40 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3166681 Bytes = 3 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 01100000 ... Image Name: initramfs-4.4.0-kirkwood-tld-1 Created: 2016-02-19 7:33:04 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7179871 Bytes = 6.8 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine model: NETGEAR MS2000 / MS2110 aka Stora [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=orion_nand:0x100000@0(uboot),0xff00000@0x100000(root) root=LABEL=rootfs rootfstype=ext2 rootdelay=10 [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 113620K/131072K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 17452K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc07d7ef4 (8000 kB) [ 0.000000] .init : 0xc07d8000 - 0xc0822000 ( 296 kB) [ 0.000000] .data : 0xc0822000 - 0xc08b169c ( 574 kB) [ 0.000000] .bss : 0xc08b169c - 0xc08ff9d0 ( 313 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000010] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000389] Console: colour dummy device 80x30 [ 0.000427] Calibrating delay loop... 990.41 BogoMIPS (lpj=4952064) [ 0.090107] pid_max: default: 32768 minimum: 301 [ 0.090236] Security Framework initialized [ 0.090329] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090354] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.091296] Initializing cgroup subsys io [ 0.091335] Initializing cgroup subsys devices [ 0.091375] Initializing cgroup subsys freezer [ 0.091405] Initializing cgroup subsys net_cls [ 0.091501] CPU: Testing write buffer coherency: ok [ 0.092023] Setting up static identity map for 0x8200 - 0x8258 [ 0.092397] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.096770] devtmpfs: initialized [ 0.103108] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.103645] prandom: seed boundary self test passed [ 0.108152] prandom: 100 self tests passed [ 0.108183] pinctrl core: initialized pinctrl subsystem [ 0.109833] NET: Registered protocol family 16 [ 0.110489] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.140125] cpuidle: using governor ladder [ 0.170123] cpuidle: using governor menu [ 0.170641] Feroceon L2: Enabling L2 [ 0.170694] Feroceon L2: Cache support initialised. [ 0.171148] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.177710] No ATAGs? [ 0.211886] vgaarb: loaded [ 0.212332] usbcore: registered new interface driver usbfs [ 0.212431] usbcore: registered new interface driver hub [ 0.212508] usbcore: registered new device driver usb [ 0.213851] clocksource: Switched to clocksource orion_clocksource [ 0.281108] NET: Registered protocol family 2 [ 0.282047] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.282080] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.282105] TCP: Hash tables configured (established 1024 bind 1024) [ 0.282186] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.282215] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.282451] NET: Registered protocol family 1 [ 0.282933] RPC: Registered named UNIX socket transport module. [ 0.282948] RPC: Registered udp transport module. [ 0.282957] RPC: Registered tcp transport module. [ 0.282966] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.283298] Unpacking initramfs... [ 1.046800] Freeing initrd memory: 7012K (c1100000 - c17d9000) [ 1.046972] NetWinder Floating Point Emulator V0.97 (double precision) [ 1.048302] futex hash table entries: 256 (order: -1, 3072 bytes) [ 1.048390] audit: initializing netlink subsys (disabled) [ 1.048449] audit: type=2000 audit(1.040:1): initialized [ 1.048878] Initialise system trusted keyring [ 1.049358] zbud: loaded [ 1.049714] VFS: Disk quotas dquot_6.6.0 [ 1.049785] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.050444] NFS: Registering the id_resolver key type [ 1.050496] Key type id_resolver registered [ 1.050508] Key type id_legacy registered [ 1.050540] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.050557] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 1.050824] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.051453] Key type big_key registered [ 1.075683] Key type asymmetric registered [ 1.075711] Asymmetric key parser 'x509' registered [ 1.075827] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 1.075853] io scheduler noop registered [ 1.075873] io scheduler deadline registered [ 1.075945] io scheduler cfq registered (default) [ 1.077569] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 1.078392] irq: Cannot allocate irq_descs @ IRQ34, assuming pre-allocated [ 1.078918] irq: Cannot allocate irq_descs @ IRQ66, assuming pre-allocated [ 1.079936] mvebu-pcie mbus:pcie-controller: PCI host bridge to bus 0000:00 [ 1.079960] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 1.079977] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 1.079993] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.080470] PCI: bus0: Fast back to back transfers disabled [ 1.080502] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.080753] PCI: bus1: Fast back to back transfers enabled [ 1.080861] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.081259] mv_xor f1060800.xor: Marvell shared XOR driver [ 1.124711] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.125003] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.164690] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.165300] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 1.167004] console [ttyS0] disabled [ 1.167082] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 1.819289] console [ttyS0] enabled [ 1.824373] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xda [ 1.830761] nand: Samsung NAND 256MiB 3,3V 8-bit [ 1.835437] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.843066] Scanning device for bad blocks [ 1.873679] Bad eraseblock 246 at 0x000001ec0000 [ 1.920579] Bad eraseblock 640 at 0x000005000000 [ 1.931613] Bad eraseblock 700 at 0x000005780000 [ 1.936443] Bad eraseblock 702 at 0x0000057c0000 [ 2.002018] Bad eraseblock 1270 at 0x000009ec0000 [ 2.027547] Bad eraseblock 1464 at 0x00000b700000 [ 2.053767] Bad eraseblock 1664 at 0x00000d000000 [ 2.064924] Bad eraseblock 1724 at 0x00000d780000 [ 2.069815] Bad eraseblock 1726 at 0x00000d7c0000 [ 2.078579] Bad eraseblock 1764 at 0x00000dc80000 [ 2.113705] 2 cmdlinepart partitions found on MTD device orion_nand [ 2.120026] Creating 2 MTD partitions on "orion_nand": [ 2.125219] 0x000000000000-0x000000100000 : "uboot" [ 2.131684] 0x000000100000-0x000010000000 : "root" [ 2.139819] libphy: Fixed MDIO Bus: probed [ 2.144405] libphy: orion_mdio_bus: probed [ 2.154277] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 3.232704] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:50:43:00:02:02 [ 3.241662] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.248285] ehci-pci: EHCI PCI platform driver [ 3.252849] ehci-orion: EHCI orion driver [ 3.257139] orion-ehci f1050000.ehci: EHCI Host Controller [ 3.262687] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 3.270605] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 3.293892] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 3.300210] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.307069] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.314355] usb usb1: Product: EHCI Host Controller [ 3.319259] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd [ 3.325925] usb usb1: SerialNumber: f1050000.ehci [ 3.331568] hub 1-0:1.0: USB hub found [ 3.335441] hub 1-0:1.0: 1 port detected [ 3.340593] mousedev: PS/2 mouse device common for all mice [ 3.653891] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 3.806363] usb 1-1: New USB device found, idVendor=125f, idProduct=c83a [ 3.813115] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.820321] usb 1-1: Product: A-DATA USB Flash Drive [ 3.825347] usb 1-1: Manufacturer: A-DATA [ 3.829378] usb 1-1: SerialNumber: 06e7cf43be21fe [ 4.353890] rtc-mv f1010300.rtc: internal RTC not ticking [ 4.359583] i2c /dev entries driver [ 4.364284] rtc-pcf8563 0-0051: chip found, driver version 0.4.4 [ 4.376372] rtc-pcf8563 0-0051: rtc core: registered rtc-pcf8563 as rtc0 [ 4.386266] hidraw: raw HID events driver (C) Jiri Kosina [ 4.392157] drop_monitor: Initializing network drop monitor service [ 4.398815] NET: Registered protocol family 17 [ 4.403606] Key type dns_resolver registered [ 4.408985] registered taskstats version 1 [ 4.413154] Loading compiled-in X.509 certificates [ 4.418077] zswap: loaded using pool lzo/zbud [ 4.432906] Key type encrypted registered [ 4.438977] rtc-pcf8563 0-0051: setting system clock to 2017-03-18 14:26:49 UTC (1489847209) [ 4.450858] Freeing unused kernel memory: 296K (c07d8000 - c0822000) Loading, please wait... [ 4.540770] systemd-udevd[81]: starting version 215 [ 4.556523] random: systemd-udevd urandom read with 8 bits of entropy available [ 4.770105] SCSI subsystem initialized [ 4.819921] usb-storage 1-1:1.0: USB Mass Storage device detected [ 4.840150] sata_mv f1080000.sata: slots 32 ports 2 [ 4.872713] scsi host0: usb-storage 1-1:1.0 [ 4.888775] usbcore: registered new interface driver usb-storage [ 4.898329] scsi host1: sata_mv [ 4.916463] scsi host2: sata_mv [ 4.920072] ata1: SATA max UDMA/133 irq 33 [ 4.930547] usbcore: registered new interface driver uas [ 4.953286] ata2: SATA max UDMA/133 irq 33 [ 5.313905] ata1: SATA link down (SStatus 0 SControl F300) [ 5.683915] ata2: SATA link down (SStatus 0 SControl F300) [ 5.885357] scsi 0:0:0:0: Direct-Access A-DATA USB Flash Drive 0.00 PQ: 0 ANSI: 2 [ 5.901569] sd 0:0:0:0: [sda] 7897088 512-byte logical blocks: (4.04 GB/3.76 GiB) [ 5.912919] sd 0:0:0:0: [sda] Write Protect is off [ 5.918400] sd 0:0:0:0: [sda] Asking for cache data failed [ 5.924075] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 6.040179] sda: sda1 [ 6.046923] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 6.057534] sd 0:0:0:0: Attached scsi generic sg0 type 0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Checking root file system ... fsck from util-linux 2.25.2 rootfs: clean, 14839/247008 files, 198718/986880 blocks done. done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 17.367659] systemd-udevd[291]: starting version 215 . ok [....] Synthesizing the initial hotplug events...[ 17.667526] input: gpio-keys as /devices/platform/gpio-keys/input/input0 done. [....] Waiting for /dev to be fully populated...[ 18.010363] orion_wdt: Initial timeout 21 sec [ 18.059426] lm75 0-0048: hwmon0: sensor 'lm75' [ 18.066111] marvell-cesa: probe of f1030000.crypto failed with error -524 [ 18.156643] random: nonblocking pool is initialized done. [ ok ] Activating swap...done. [....] Checking root file system...fsck from util-linux 2.25.2 rootfs: clean, 14839/247008 files, 198718/986880 blocks done. [ ok ] Activating lvm and md swap...done. [....] Checking file systems...fsck from util-linux 2.25.2 done. [ ok ] Loading kernel modules...done. [ ok ] Cleaning up temporary files... /tmp. [ ok ] Mounting local filesystems...done. [ ok ] Activating swapfile swap...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables ...done. [ 22.806879] NET: Registered protocol family 10 [ 23.996337] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1 Copyright 2004-2014 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:50:43:00:02:02 Sending on LPF/eth0/00:50:43:00:02:02 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4 [ 27.034293] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 27.044231] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5 DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPOFFER from 192.168.1.1 DHCPACK from 192.168.1.1 bound to 192.168.1.217 -- renewal in 32972 seconds. done. [ ok ] Starting rpcbind daemon.... [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1235 (syslogd) . ok [ ok ] Starting system message bus: dbus. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1238 (klogd) . ok [ ok ] Starting OpenBSD Secure Shell server: sshd. Debian GNU/Linux 8 debian ttyS0 debian login: root Password: Last login: Sat Mar 18 13:40:44 CET 2017 on ttyS0 Linux debian 4.4.0-kirkwood-tld-1 #1 PREEMPT Mon Jan 25 20:35:24 PST 2016 armv5tel The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 00100000 00020000 "uboot" mtd1: 0ff00000 00020000 "root" root@debian:~# cat /etc/fw_env.config # Configuration file for fw_(printenv/saveenv) utility. # Up to two entries are valid, in this case the redundant # environment sector is assumed present. # Notice, that the "Number of sectors" is ignored on NOR. # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd0 0xc0000 0x20000 0x20000 root@debian:~# fw_printenv ethaddr [ 729.598503] __nand_correct_data: uncorrectable ECC error [ 729.603937] __nand_correct_data: uncorrectable ECC error [ 729.609309] __nand_correct_data: uncorrectable ECC error [ 729.615156] __nand_correct_data: uncorrectable ECC error [ 729.620544] __nand_correct_data: uncorrectable ECC error [ 729.626223] __nand_correct_data: uncorrectable ECC error [ 729.631574] __nand_correct_data: uncorrectable ECC error [ 729.637636] __nand_correct_data: uncorrectable ECC error [ 729.642973] __nand_correct_data: uncorrectable ECC error [ 729.648614] __nand_correct_data: uncorrectable ECC error [ 729.653983] __nand_correct_data: uncorrectable ECC error [ 729.659322] __nand_correct_data: uncorrectable ECC error [ 729.665031] __nand_correct_data: uncorrectable ECC error [ 729.670371] __nand_correct_data: uncorrectable ECC error [ 729.676422] __nand_correct_data: uncorrectable ECC error [ 729.681760] __nand_correct_data: uncorrectable ECC error [ 729.687395] __nand_correct_data: uncorrectable ECC error [ 729.692729] __nand_correct_data: uncorrectable ECC error [ 729.698365] __nand_correct_data: uncorrectable ECC error [ 729.703699] __nand_correct_data: uncorrectable ECC error [ 729.709333] __nand_correct_data: uncorrectable ECC error [ 729.715117] __nand_correct_data: uncorrectable ECC error [ 729.720450] __nand_correct_data: uncorrectable ECC error [ 729.726155] __nand_correct_data: uncorrectable ECC error [ 729.731489] __nand_correct_data: uncorrectable ECC error [ 729.737123] __nand_correct_data: uncorrectable ECC error [ 729.742460] __nand_correct_data: uncorrectable ECC error [ 729.748100] __nand_correct_data: uncorrectable ECC error [ 729.754072] __nand_correct_data: uncorrectable ECC error [ 729.759411] __nand_correct_data: uncorrectable ECC error [ 729.765043] __nand_correct_data: uncorrectable ECC error [ 729.770380] __nand_correct_data: uncorrectable ECC error [ 729.776013] __nand_correct_data: uncorrectable ECC error [ 729.781350] __nand_correct_data: uncorrectable ECC error [ 729.786980] __nand_correct_data: uncorrectable ECC error [ 729.792739] __nand_correct_data: uncorrectable ECC error [ 729.798374] __nand_correct_data: uncorrectable ECC error [ 729.803717] __nand_correct_data: uncorrectable ECC error [ 729.809348] __nand_correct_data: uncorrectable ECC error [ 729.814722] __nand_correct_data: uncorrectable ECC error [ 729.820058] __nand_correct_data: uncorrectable ECC error [ 729.825767] __nand_correct_data: uncorrectable ECC error [ 729.831525] __nand_correct_data: uncorrectable ECC error [ 729.837161] __nand_correct_data: uncorrectable ECC error [ 729.842504] __nand_correct_data: uncorrectable ECC error [ 729.848136] __nand_correct_data: uncorrectable ECC error [ 729.853473] __nand_correct_data: uncorrectable ECC error [ 729.859107] __nand_correct_data: uncorrectable ECC error [ 729.864473] __nand_correct_data: uncorrectable ECC error [ 729.870224] __nand_correct_data: uncorrectable ECC error [ 729.875928] __nand_correct_data: uncorrectable ECC error [ 729.881264] __nand_correct_data: uncorrectable ECC error [ 729.886896] __nand_correct_data: uncorrectable ECC error [ 729.892235] __nand_correct_data: uncorrectable ECC error [ 729.897866] __nand_correct_data: uncorrectable ECC error [ 729.903204] __nand_correct_data: uncorrectable ECC error [ 729.909254] __nand_correct_data: uncorrectable ECC error [ 729.914623] __nand_correct_data: uncorrectable ECC error [ 729.919964] __nand_correct_data: uncorrectable ECC error [ 729.925665] __nand_correct_data: uncorrectable ECC error [ 729.931003] __nand_correct_data: uncorrectable ECC error [ 729.936634] __nand_correct_data: uncorrectable ECC error [ 729.941973] __nand_correct_data: uncorrectable ECC error [ 729.948024] __nand_correct_data: uncorrectable ECC error [ 729.953362] __nand_correct_data: uncorrectable ECC error [ 729.958994] __nand_correct_data: uncorrectable ECC error [ 729.964361] __nand_correct_data: uncorrectable ECC error [ 729.969693] __nand_correct_data: uncorrectable ECC error [ 729.975504] __nand_correct_data: uncorrectable ECC error [ 729.980906] __nand_correct_data: uncorrectable ECC error [ 729.987074] __nand_correct_data: uncorrectable ECC error [ 729.992452] __nand_correct_data: uncorrectable ECC error [ 729.998101] __nand_correct_data: uncorrectable ECC error [ 730.003471] __nand_correct_data: uncorrectable ECC error [ 730.009222] __nand_correct_data: uncorrectable ECC error [ 730.014596] __nand_correct_data: uncorrectable ECC error [ 730.019940] __nand_correct_data: uncorrectable ECC error [ 730.026076] __nand_correct_data: uncorrectable ECC error [ 730.031414] __nand_correct_data: uncorrectable ECC error [ 730.037054] __nand_correct_data: uncorrectable ECC error [ 730.042393] __nand_correct_data: uncorrectable ECC error [ 730.048027] __nand_correct_data: uncorrectable ECC error [ 730.053362] __nand_correct_data: uncorrectable ECC error [ 730.059002] __nand_correct_data: uncorrectable ECC error [ 730.064791] __nand_correct_data: uncorrectable ECC error [ 730.070131] __nand_correct_data: uncorrectable ECC error [ 730.075835] __nand_correct_data: uncorrectable ECC error [ 730.081185] __nand_correct_data: uncorrectable ECC error [ 730.086818] __nand_correct_data: uncorrectable ECC error [ 730.092158] __nand_correct_data: uncorrectable ECC error [ 730.097790] __nand_correct_data: uncorrectable ECC error [ 730.103545] __nand_correct_data: uncorrectable ECC error [ 730.109181] __nand_correct_data: uncorrectable ECC error [ 730.114545] __nand_correct_data: uncorrectable ECC error [ 730.119878] __nand_correct_data: uncorrectable ECC error [ 730.125591] __nand_correct_data: uncorrectable ECC error [ 730.130926] __nand_correct_data: uncorrectable ECC error [ 730.136559] __nand_correct_data: uncorrectable ECC error [ 730.142315] __nand_correct_data: uncorrectable ECC error [ 730.147950] __nand_correct_data: uncorrectable ECC error [ 730.153309] __nand_correct_data: uncorrectable ECC error [ 730.158937] __nand_correct_data: uncorrectable ECC error [ 730.164302] __nand_correct_data: uncorrectable ECC error [ 730.169634] __nand_correct_data: uncorrectable ECC error [ 730.175340] __nand_correct_data: uncorrectable ECC error [ 730.181102] __nand_correct_data: uncorrectable ECC error [ 730.186736] __nand_correct_data: uncorrectable ECC error [ 730.192071] __nand_correct_data: uncorrectable ECC error [ 730.197706] __nand_correct_data: uncorrectable ECC error [ 730.203041] __nand_correct_data: uncorrectable ECC error [ 730.208672] __nand_correct_data: uncorrectable ECC error [ 730.214041] __nand_correct_data: uncorrectable ECC error [ 730.219791] __nand_correct_data: uncorrectable ECC error [ 730.225559] __nand_correct_data: uncorrectable ECC error [ 730.230933] __nand_correct_data: uncorrectable ECC error [ 730.236612] __nand_correct_data: uncorrectable ECC error [ 730.241980] __nand_correct_data: uncorrectable ECC error [ 730.247628] __nand_correct_data: uncorrectable ECC error [ 730.252962] __nand_correct_data: uncorrectable ECC error [ 730.259016] __nand_correct_data: uncorrectable ECC error [ 730.264383] __nand_correct_data: uncorrectable ECC error [ 730.269723] __nand_correct_data: uncorrectable ECC error [ 730.275431] __nand_correct_data: uncorrectable ECC error [ 730.280771] __nand_correct_data: uncorrectable ECC error [ 730.286405] __nand_correct_data: uncorrectable ECC error [ 730.291740] __nand_correct_data: uncorrectable ECC error [ 730.297792] __nand_correct_data: uncorrectable ECC error [ 730.303129] __nand_correct_data: uncorrectable ECC error [ 730.308764] __nand_correct_data: uncorrectable ECC error [ 730.314130] __nand_correct_data: uncorrectable ECC error [ 730.319471] __nand_correct_data: uncorrectable ECC error [ 730.325173] __nand_correct_data: uncorrectable ECC error [ 730.330510] __nand_correct_data: uncorrectable ECC error [ 730.336559] __nand_correct_data: uncorrectable ECC error [ 730.341898] __nand_correct_data: uncorrectable ECC error [ 730.347535] __nand_correct_data: uncorrectable ECC error [ 730.352877] __nand_correct_data: uncorrectable ECC error [ 730.358509] __nand_correct_data: uncorrectable ECC error [ 730.363876] __nand_correct_data: uncorrectable ECC error [ 730.369209] __nand_correct_data: uncorrectable ECC error [ 730.375334] __nand_correct_data: uncorrectable ECC error [ 730.380676] __nand_correct_data: uncorrectable ECC error [ 730.386311] __nand_correct_data: uncorrectable ECC error [ 730.391646] __nand_correct_data: uncorrectable ECC error [ 730.397278] __nand_correct_data: uncorrectable ECC error [ 730.402616] __nand_correct_data: uncorrectable ECC error [ 730.408248] __nand_correct_data: uncorrectable ECC error [ 730.414221] __nand_correct_data: uncorrectable ECC error [ 730.419558] __nand_correct_data: uncorrectable ECC error [ 730.425191] __nand_correct_data: uncorrectable ECC error [ 730.430528] __nand_correct_data: uncorrectable ECC error [ 730.436160] __nand_correct_data: uncorrectable ECC error [ 730.441499] __nand_correct_data: uncorrectable ECC error [ 730.447128] __nand_correct_data: uncorrectable ECC error [ 730.452886] __nand_correct_data: uncorrectable ECC error [ 730.458519] __nand_correct_data: uncorrectable ECC error [ 730.463886] __nand_correct_data: uncorrectable ECC error [ 730.469218] __nand_correct_data: uncorrectable ECC error [ 730.474918] __nand_correct_data: uncorrectable ECC error [ 730.480259] __nand_correct_data: uncorrectable ECC error [ 730.485891] __nand_correct_data: uncorrectable ECC error [ 730.491647] __nand_correct_data: uncorrectable ECC error [ 730.497283] __nand_correct_data: uncorrectable ECC error [ 730.502625] __nand_correct_data: uncorrectable ECC error [ 730.508259] __nand_correct_data: uncorrectable ECC error [ 730.513595] __nand_correct_data: uncorrectable ECC error [ 730.519226] __nand_correct_data: uncorrectable ECC error [ 730.524594] __nand_correct_data: uncorrectable ECC error [ 730.530346] __nand_correct_data: uncorrectable ECC error [ 730.536056] __nand_correct_data: uncorrectable ECC error [ 730.541469] __nand_correct_data: uncorrectable ECC error [ 730.547145] __nand_correct_data: uncorrectable ECC error [ 730.552487] __nand_correct_data: uncorrectable ECC error [ 730.558144] __nand_correct_data: uncorrectable ECC error [ 730.563483] __nand_correct_data: uncorrectable ECC error [ 730.569555] __nand_correct_data: uncorrectable ECC error [ 730.574928] __nand_correct_data: uncorrectable ECC error [ 730.580268] __nand_correct_data: uncorrectable ECC error [ 730.585973] __nand_correct_data: uncorrectable ECC error [ 730.591308] __nand_correct_data: uncorrectable ECC error [ 730.596941] __nand_correct_data: uncorrectable ECC error [ 730.602278] __nand_correct_data: uncorrectable ECC error [ 730.608328] __nand_correct_data: uncorrectable ECC error [ 730.613666] __nand_correct_data: uncorrectable ECC error [ 730.619301] __nand_correct_data: uncorrectable ECC error [ 730.624675] __nand_correct_data: uncorrectable ECC error [ 730.630007] __nand_correct_data: uncorrectable ECC error [ 730.635710] __nand_correct_data: uncorrectable ECC error [ 730.641047] __nand_correct_data: uncorrectable ECC error [ 730.647096] __nand_correct_data: uncorrectable ECC error [ 730.652436] __nand_correct_data: uncorrectable ECC error [ 730.658069] __nand_correct_data: uncorrectable ECC error [ 730.663405] __nand_correct_data: uncorrectable ECC error [ 730.669037] __nand_correct_data: uncorrectable ECC error [ 730.674404] __nand_correct_data: uncorrectable ECC error [ 730.679737] __nand_correct_data: uncorrectable ECC error [ 730.685865] __nand_correct_data: uncorrectable ECC error [ 730.691204] __nand_correct_data: uncorrectable ECC error [ 730.696838] __nand_correct_data: uncorrectable ECC error [ 730.702173] __nand_correct_data: uncorrectable ECC error [ 730.707807] __nand_correct_data: uncorrectable ECC error [ 730.713144] __nand_correct_data: uncorrectable ECC error [ 730.718777] __nand_correct_data: uncorrectable ECC error [ 730.724562] __nand_correct_data: uncorrectable ECC error [ 730.729894] __nand_correct_data: uncorrectable ECC error [ 730.735604] __nand_correct_data: uncorrectable ECC error [ 730.740943] __nand_correct_data: uncorrectable ECC error [ 730.746576] __nand_correct_data: uncorrectable ECC error [ 730.751913] __nand_correct_data: uncorrectable ECC error [ 730.757546] __nand_correct_data: uncorrectable ECC error [ 730.763301] __nand_correct_data: uncorrectable ECC error [ 730.768936] __nand_correct_data: uncorrectable ECC error [ 730.774301] __nand_correct_data: uncorrectable ECC error [ 730.779633] __nand_correct_data: uncorrectable ECC error [ 730.785335] __nand_correct_data: uncorrectable ECC error [ 730.790673] __nand_correct_data: uncorrectable ECC error [ 730.796307] __nand_correct_data: uncorrectable ECC error [ 730.802061] __nand_correct_data: uncorrectable ECC error [ 730.807694] __nand_correct_data: uncorrectable ECC error [ 730.813031] __nand_correct_data: uncorrectable ECC error [ 730.818664] __nand_correct_data: uncorrectable ECC error [ 730.824032] __nand_correct_data: uncorrectable ECC error [ 730.829372] __nand_correct_data: uncorrectable ECC error [ 730.835074] __nand_correct_data: uncorrectable ECC error [ 730.840831] __nand_correct_data: uncorrectable ECC error [ 730.846465] __nand_correct_data: uncorrectable ECC error [ 730.851801] __nand_correct_data: uncorrectable ECC error [ 730.857433] __nand_correct_data: uncorrectable ECC error [ 730.862770] __nand_correct_data: uncorrectable ECC error [ 730.868401] __nand_correct_data: uncorrectable ECC error [ 730.873739] __nand_correct_data: uncorrectable ECC error [ 730.879792] __nand_correct_data: uncorrectable ECC error [ 730.885159] __nand_correct_data: uncorrectable ECC error [ 730.890500] __nand_correct_data: uncorrectable ECC error [ 730.896199] __nand_correct_data: uncorrectable ECC error [ 730.901539] __nand_correct_data: uncorrectable ECC error [ 730.907172] __nand_correct_data: uncorrectable ECC error [ 730.912509] __nand_correct_data: uncorrectable ECC error [ 730.918559] __nand_correct_data: uncorrectable ECC error [ 730.923927] __nand_correct_data: uncorrectable ECC error [ 730.929260] __nand_correct_data: uncorrectable ECC error [ 730.934968] __nand_correct_data: uncorrectable ECC error [ 730.940308] __nand_correct_data: uncorrectable ECC error [ 730.945946] __nand_correct_data: uncorrectable ECC error [ 730.951287] __nand_correct_data: uncorrectable ECC error [ 730.957336] __nand_correct_data: uncorrectable ECC error [ 730.962675] __nand_correct_data: uncorrectable ECC error [ 730.968311] __nand_correct_data: uncorrectable ECC error [ 730.973654] __nand_correct_data: uncorrectable ECC error [ 730.979286] __nand_correct_data: uncorrectable ECC error [ 730.984653] __nand_correct_data: uncorrectable ECC error [ 730.989985] __nand_correct_data: uncorrectable ECC error [ 730.996110] __nand_correct_data: uncorrectable ECC error [ 731.001453] __nand_correct_data: uncorrectable ECC error [ 731.007125] __nand_correct_data: uncorrectable ECC error [ 731.012466] __nand_correct_data: uncorrectable ECC error [ 731.018215] __nand_correct_data: uncorrectable ECC error [ 731.023559] __nand_correct_data: uncorrectable ECC error [ 731.029202] __nand_correct_data: uncorrectable ECC error [ 731.034988] __nand_correct_data: uncorrectable ECC error [ 731.040326] __nand_correct_data: uncorrectable ECC error [ 731.046037] __nand_correct_data: uncorrectable ECC error [ 731.051375] __nand_correct_data: uncorrectable ECC error [ 731.057010] __nand_correct_data: uncorrectable ECC error [ 731.062345] __nand_correct_data: uncorrectable ECC error [ 731.067977] __nand_correct_data: uncorrectable ECC error [ 731.073733] __nand_correct_data: uncorrectable ECC error [ 731.079376] __nand_correct_data: uncorrectable ECC error [ 731.084742] __nand_correct_data: uncorrectable ECC error [ 731.090074] __nand_correct_data: uncorrectable ECC error [ 731.095774] __nand_correct_data: uncorrectable ECC error [ 731.101114] __nand_correct_data: uncorrectable ECC error [ 731.106747] __nand_correct_data: uncorrectable ECC error [ 731.112501] __nand_correct_data: uncorrectable ECC error [ 731.118135] __nand_correct_data: uncorrectable ECC error [ 731.123472] __nand_correct_data: uncorrectable ECC error [ 731.129105] __nand_correct_data: uncorrectable ECC error [ 731.134472] __nand_correct_data: uncorrectable ECC error [ 731.139804] __nand_correct_data: uncorrectable ECC error [ 731.145505] __nand_correct_data: uncorrectable ECC error [ 731.151263] __nand_correct_data: uncorrectable ECC error [ 731.156897] __nand_correct_data: uncorrectable ECC error [ 731.162232] __nand_correct_data: uncorrectable ECC error [ 731.167865] __nand_correct_data: uncorrectable ECC error [ 731.173202] __nand_correct_data: uncorrectable ECC error [ 731.178833] __nand_correct_data: uncorrectable ECC error [ 731.184202] __nand_correct_data: uncorrectable ECC error [ 731.189962] __nand_correct_data: uncorrectable ECC error [ 731.195669] __nand_correct_data: uncorrectable ECC error [ 731.201010] __nand_correct_data: uncorrectable ECC error [ 731.206641] __nand_correct_data: uncorrectable ECC error [ 731.211980] __nand_correct_data: uncorrectable ECC error [ 731.217613] __nand_correct_data: uncorrectable ECC error [ 731.222950] __nand_correct_data: uncorrectable ECC error [ 731.229024] __nand_correct_data: uncorrectable ECC error [ 731.234397] __nand_correct_data: uncorrectable ECC error [ 731.239735] __nand_correct_data: uncorrectable ECC error [ 731.245499] __nand_correct_data: uncorrectable ECC error [ 731.250866] __nand_correct_data: uncorrectable ECC error [ 731.256545] __nand_correct_data: uncorrectable ECC error [ 731.261915] __nand_correct_data: uncorrectable ECC error [ 731.267987] __nand_correct_data: uncorrectable ECC error [ 731.273325] __nand_correct_data: uncorrectable ECC error [ 731.278966] __nand_correct_data: uncorrectable ECC error [ 731.284335] __nand_correct_data: uncorrectable ECC error [ 731.289675] __nand_correct_data: uncorrectable ECC error [ 731.295377] __nand_correct_data: uncorrectable ECC error [ 731.300715] __nand_correct_data: uncorrectable ECC error [ 731.306767] __nand_correct_data: uncorrectable ECC error [ 731.312102] __nand_correct_data: uncorrectable ECC error [ 731.317741] __nand_correct_data: uncorrectable ECC error [ 731.323082] __nand_correct_data: uncorrectable ECC error [ 731.328716] __nand_correct_data: uncorrectable ECC error [ 731.334081] __nand_correct_data: uncorrectable ECC error [ 731.339413] __nand_correct_data: uncorrectable ECC error [ 731.345532] __nand_correct_data: uncorrectable ECC error [ 731.350872] __nand_correct_data: uncorrectable ECC error [ 731.356505] __nand_correct_data: uncorrectable ECC error [ 731.361841] __nand_correct_data: uncorrectable ECC error [ 731.367474] __nand_correct_data: uncorrectable ECC error [ 731.372812] __nand_correct_data: uncorrectable ECC error [ 731.378443] __nand_correct_data: uncorrectable ECC error [ 731.384420] __nand_correct_data: uncorrectable ECC error [ 731.389764] __nand_correct_data: uncorrectable ECC error [ 731.395403] __nand_correct_data: uncorrectable ECC error [ 731.400742] __nand_correct_data: uncorrectable ECC error [ 731.406373] __nand_correct_data: uncorrectable ECC error [ 731.411712] __nand_correct_data: uncorrectable ECC error [ 731.417344] __nand_correct_data: uncorrectable ECC error [ 731.423099] __nand_correct_data: uncorrectable ECC error [ 731.428736] __nand_correct_data: uncorrectable ECC error [ 731.434108] __nand_correct_data: uncorrectable ECC error [ 731.439440] __nand_correct_data: uncorrectable ECC error [ 731.445146] __nand_correct_data: uncorrectable ECC error [ 731.450481] __nand_correct_data: uncorrectable ECC error [ 731.456114] __nand_correct_data: uncorrectable ECC error [ 731.461868] __nand_correct_data: uncorrectable ECC error [ 731.467503] __nand_correct_data: uncorrectable ECC error [ 731.472838] __nand_correct_data: uncorrectable ECC error [ 731.478471] __nand_correct_data: uncorrectable ECC error [ 731.483808] __nand_correct_data: uncorrectable ECC error [ 731.489439] __nand_correct_data: uncorrectable ECC error [ 731.494808] __nand_correct_data: uncorrectable ECC error [ 731.500559] __nand_correct_data: uncorrectable ECC error [ 731.506268] __nand_correct_data: uncorrectable ECC error [ 731.511608] __nand_correct_data: uncorrectable ECC error [ 731.517240] __nand_correct_data: uncorrectable ECC error [ 731.522577] __nand_correct_data: uncorrectable ECC error [ 731.528210] __nand_correct_data: uncorrectable ECC error [ 731.533547] __nand_correct_data: uncorrectable ECC error [ 731.539597] __nand_correct_data: uncorrectable ECC error [ 731.544966] __nand_correct_data: uncorrectable ECC error [ 731.550307] __nand_correct_data: uncorrectable ECC error [ 731.556015] __nand_correct_data: uncorrectable ECC error [ 731.561355] __nand_correct_data: uncorrectable ECC error [ 731.566990] __nand_correct_data: uncorrectable ECC error [ 731.572325] __nand_correct_data: uncorrectable ECC error [ 731.578376] __nand_correct_data: uncorrectable ECC error [ 731.583713] __nand_correct_data: uncorrectable ECC error [ 731.589352] __nand_correct_data: uncorrectable ECC error [ 731.594812] __nand_correct_data: uncorrectable ECC error [ 731.600151] __nand_correct_data: uncorrectable ECC error [ 731.605886] __nand_correct_data: uncorrectable ECC error [ 731.611225] __nand_correct_data: uncorrectable ECC error [ 731.617301] __nand_correct_data: uncorrectable ECC error [ 731.622639] __nand_correct_data: uncorrectable ECC error [ 731.628277] __nand_correct_data: uncorrectable ECC error [ 731.633618] __nand_correct_data: uncorrectable ECC error [ 731.639252] __nand_correct_data: uncorrectable ECC error [ 731.644618] __nand_correct_data: uncorrectable ECC error [ 731.649950] __nand_correct_data: uncorrectable ECC error [ 731.656069] __nand_correct_data: uncorrectable ECC error [ 731.661409] __nand_correct_data: uncorrectable ECC error [ 731.667044] __nand_correct_data: uncorrectable ECC error [ 731.672379] __nand_correct_data: uncorrectable ECC error [ 731.678012] __nand_correct_data: uncorrectable ECC error [ 731.683348] __nand_correct_data: uncorrectable ECC error [ 731.688981] __nand_correct_data: uncorrectable ECC error [ 731.694767] __nand_correct_data: uncorrectable ECC error [ 731.700108] __nand_correct_data: uncorrectable ECC error [ 731.705817] __nand_correct_data: uncorrectable ECC error [ 731.711156] __nand_correct_data: uncorrectable ECC error [ 731.716788] __nand_correct_data: uncorrectable ECC error [ 731.722127] __nand_correct_data: uncorrectable ECC error [ 731.727759] __nand_correct_data: uncorrectable ECC error [ 731.733514] __nand_correct_data: uncorrectable ECC error [ 731.739149] __nand_correct_data: uncorrectable ECC error [ 731.744515] __nand_correct_data: uncorrectable ECC error [ 731.749856] __nand_correct_data: uncorrectable ECC error [ 731.755563] __nand_correct_data: uncorrectable ECC error [ 731.760904] __nand_correct_data: uncorrectable ECC error [ 731.766538] __nand_correct_data: uncorrectable ECC error [ 731.772292] __nand_correct_data: uncorrectable ECC error [ 731.777925] __nand_correct_data: uncorrectable ECC error [ 731.783262] __nand_correct_data: uncorrectable ECC error [ 731.788895] __nand_correct_data: uncorrectable ECC error [ 731.794263] __nand_correct_data: uncorrectable ECC error [ 731.799595] __nand_correct_data: uncorrectable ECC error [ 731.805294] __nand_correct_data: uncorrectable ECC error [ 731.811052] __nand_correct_data: uncorrectable ECC error [ 731.816687] __nand_correct_data: uncorrectable ECC error [ 731.822022] __nand_correct_data: uncorrectable ECC error [ 731.827655] __nand_correct_data: uncorrectable ECC error [ 731.832992] __nand_correct_data: uncorrectable ECC error [ 731.838625] __nand_correct_data: uncorrectable ECC error [ 731.843992] __nand_correct_data: uncorrectable ECC error [ 731.849743] __nand_correct_data: uncorrectable ECC error [ 731.855446] __nand_correct_data: uncorrectable ECC error [ 731.860783] __nand_correct_data: uncorrectable ECC error [ 731.866414] __nand_correct_data: uncorrectable ECC error [ 731.871752] __nand_correct_data: uncorrectable ECC error [ 731.877385] __nand_correct_data: uncorrectable ECC error [ 731.882722] __nand_correct_data: uncorrectable ECC error [ 731.888772] __nand_correct_data: uncorrectable ECC error [ 731.894146] __nand_correct_data: uncorrectable ECC error [ 731.899482] __nand_correct_data: uncorrectable ECC error [ 731.905192] __nand_correct_data: uncorrectable ECC error [ 731.910531] __nand_correct_data: uncorrectable ECC error [ 731.916163] __nand_correct_data: uncorrectable ECC error [ 731.921500] __nand_correct_data: uncorrectable ECC error [ 731.927551] __nand_correct_data: uncorrectable ECC error [ 731.932889] __nand_correct_data: uncorrectable ECC error [ 731.938524] __nand_correct_data: uncorrectable ECC error [ 731.943896] __nand_correct_data: uncorrectable ECC error [ 731.949229] __nand_correct_data: uncorrectable ECC error [ 731.954936] __nand_correct_data: uncorrectable ECC error [ 731.960277] __nand_correct_data: uncorrectable ECC error [ 731.966329] __nand_correct_data: uncorrectable ECC error [ 731.971666] __nand_correct_data: uncorrectable ECC error [ 731.977301] __nand_correct_data: uncorrectable ECC error [ 731.982635] __nand_correct_data: uncorrectable ECC error [ 731.988376] __nand_correct_data: uncorrectable ECC error [ 731.993781] __nand_correct_data: uncorrectable ECC error [ 731.999532] __nand_correct_data: uncorrectable ECC error [ 732.005455] __nand_correct_data: uncorrectable ECC error [ 732.010793] __nand_correct_data: uncorrectable ECC error [ 732.016555] __nand_correct_data: uncorrectable ECC error [ 732.021893] __nand_correct_data: uncorrectable ECC error [ 732.027539] __nand_correct_data: uncorrectable ECC error [ 732.032897] __nand_correct_data: uncorrectable ECC error [ 732.038530] __nand_correct_data: uncorrectable ECC error [ 732.044317] __nand_correct_data: uncorrectable ECC error [ 732.049658] __nand_correct_data: uncorrectable ECC error [ 732.055362] __nand_correct_data: uncorrectable ECC error [ 732.060698] __nand_correct_data: uncorrectable ECC error [ 732.066331] __nand_correct_data: uncorrectable ECC error [ 732.071667] __nand_correct_data: uncorrectable ECC error [ 732.077302] __nand_correct_data: uncorrectable ECC error Warning: Bad CRC, using default environment ## Error: "ethaddr" not defined root@debian:~#
I added the bootlog of the original firmware and the bootlog of usb-startup with error
|
Re: Problem installing Netgear Stora March 18, 2017 11:54AM |
Registered: 7 years ago Posts: 36 |
Hi Bodhi,
Can i install safely U-boot with above error.
Do i have to change device-offset in /etc/fw_env.config?
Can i install safely U-boot with above error.
Do i have to change device-offset in /etc/fw_env.config?
Marvell>> Marvell>> printenv console console=console=ttyS0,115200 mtdparts=orion_nand:0x100000@0(uboot),0xff00000@0x100000(root)
root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 00100000 00020000 "uboot" mtd1: 0ff00000 00020000 "root" Sorry, for all the questions, but i don't want to make a mistake and break the box. Thanks again. Erik
root@debian:~# cat /etc/fw_env.config # Configuration file for fw_(printenv/saveenv) utility. # Up to two entries are valid, in this case the redundant # environment sector is assumed present. # Notice, that the "Number of sectors" is ignored on NOR. # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd0 0xc0000 0x20000 0x20000
|
Re: Problem installing Netgear Stora March 18, 2017 02:17PM |
Registered: 7 years ago Posts: 36 |
Hi Bodhi,
Found this:
on: http://www.openstora.com/wiki/index.php?title=How_to_install_your_custom_firmware
I tryed this console command:
Booting in debian i get than:
But with fw_printenv ethaddr i get:
When i change /etc/fw_env.config
And do now a fw_printenv ethaddr
Is above good.
Please help
Erik
Found this:
Partition table
Other interesting issue related to the use of MTD devices is that there is no partition table, the layout of the disk (MTD memory I mean), is passed to kernel as parameters (PLEASE McWire explain where you pass it).
The original Stora have three partitions:
-Original-U-BOOT (1Mb)
-Original-Kernel (6Mb)
-Original-ROOTFS (249Mb)
# cat /proc/mtd
dev: size erasesize name
mtd0: 00100000 00020000 "u-boot"
mtd1: 00600000 00020000 "uImage"
mtd2: 0f900000 00020000 "root"
on: http://www.openstora.com/wiki/index.php?title=How_to_install_your_custom_firmware
I tryed this console command:
Marvell>> setenv console 'console=ttyS0,115200 mtdparts=orion_nand:0x100000@0(uboot),0x600000@0x100000(uImage),0xf900000@0x100000(root)'
Booting in debian i get than:
root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 00100000 00020000 "uboot" mtd1: 00600000 00020000 "uImage" mtd2: 0f900000 00020000 "root" root@debian:~# cat /proc/cmdline console=ttyS0,115200 mtdparts=orion_nand:0x100000@0(uboot),0x600000@0x100000(uImage),0xf900000@0x100000(root) root=LABEL=rootfs rootfstype=ext2 rootdelay=10
But with fw_printenv ethaddr i get:
root@debian:~# fw_printenv ethaddr [ 145.116718] __nand_correct_data: uncorrectable ECC error [ 145.122103] __nand_correct_data: uncorrectable ECC error ... [ 147.595031] __nand_correct_data: uncorrectable ECC error Warning: Bad CRC, using default environment ## Error: "ethaddr" not defined
When i change /etc/fw_env.config
GNU nano 2.2.6 File: /etc/fw_env.config # Configuration file for fw_(printenv/saveenv) utility. # Up to two entries are valid, in this case the redundant # environment sector is assumed present. # Notice, that the "Number of sectors" is ignored on NOR. # MTD device name Device offset Env. size Flash sector size $ #/dev/mtd0 0xc0000 0x20000 0x20000 /dev/mtd0 0x100000 0x20000 0x20000
And do now a fw_printenv ethaddr
root@debian:~# fw_printenv ethaddr Cannot read bad block mark: Invalid argument
Is above good.
Please help
Erik
|
Re: Problem installing Netgear Stora March 18, 2017 02:17PM |
Admin Registered: 13 years ago Posts: 18,543 |
Erik,
It looks OK. mtd0 is where it is important. As long as it is correct then you can install u-boot. These NAND ECC errors are shown in some boxes before installating u-boot (old u-boot wrote the envs differently, and you are using newer fw_printenv from the rootfs).
Your bad blocks are OK (in different region away from mtd0):
Your mtd0 looks OK:
However, what you should do is: to boot with kwboot before installiing u-boot. As I mentioned in the uboot thread:
If you can use the new u-boot image to boot with kwboot, then the box is unbrickable!
But even if you can't run kwboot to boot this box, it's OK to go ahead and install it.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 03/18/2017 03:04PM by bodhi.
It looks OK. mtd0 is where it is important. As long as it is correct then you can install u-boot. These NAND ECC errors are shown in some boxes before installating u-boot (old u-boot wrote the envs differently, and you are using newer fw_printenv from the rootfs).
Your bad blocks are OK (in different region away from mtd0):
[ 1.843066] Scanning device for bad blocks [ 1.873679] Bad eraseblock 246 at 0x000001ec0000 [ 1.920579] Bad eraseblock 640 at 0x000005000000 [ 1.931613] Bad eraseblock 700 at 0x000005780000 [ 1.936443] Bad eraseblock 702 at 0x0000057c0000 [ 2.002018] Bad eraseblock 1270 at 0x000009ec0000 [ 2.027547] Bad eraseblock 1464 at 0x00000b700000 [ 2.053767] Bad eraseblock 1664 at 0x00000d000000 [ 2.064924] Bad eraseblock 1724 at 0x00000d780000 [ 2.069815] Bad eraseblock 1726 at 0x00000d7c0000 [ 2.078579] Bad eraseblock 1764 at 0x00000dc80000
Your mtd0 looks OK:
root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 00100000 00020000 "uboot"
However, what you should do is: to boot with kwboot before installiing u-boot. As I mentioned in the uboot thread:
Quote
Important Note: If possible, try to test this boot image with UART booting before flashing to NAND. See davygravy's UART booting using kwboot instruction here in this thread. The latest u-boot image released here should be used for UART booting, if your box is the type that supports it (these do not: Dockstar, Pogo E02, iConnect).
If you can use the new u-boot image to boot with kwboot, then the box is unbrickable!
But even if you can't run kwboot to boot this box, it's OK to go ahead and install it.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 03/18/2017 03:04PM by bodhi.
|
Re: Problem installing Netgear Stora March 18, 2017 02:19PM |
Admin Registered: 13 years ago Posts: 18,543 |
Erik,
If you are extra careful, you should adjust the mtdparts in bootargs so that it looks like this in Debian:
# cat /proc/mtd
Note that this definition will not allow you to run stock FW.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 03/18/2017 02:21PM by bodhi.
If you are extra careful, you should adjust the mtdparts in bootargs so that it looks like this in Debian:
# cat /proc/mtd
dev: size erasesize name mtd0: 00100000 00020000 "u-boot" mtd1: 00400000 00020000 "uImage" mtd2: 02000000 00020000 "rootfs" mtd3: 0db00000 00020000 "data"
Note that this definition will not allow you to run stock FW.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 03/18/2017 02:21PM by bodhi.
|
Re: Problem installing Netgear Stora March 18, 2017 02:33PM |
Registered: 7 years ago Posts: 36 |
Hi Bodhi,
I have tested on my box version. It is 1.11, so kwboot can not be used. (My box is breakable, so i m extra careful)
Before i start i have one question about the /etc/fw_env.config file;
has the offset to be 0xc0000 --> __nand_correct_data: uncorrectable ECC error
has the offset to be 0x100000 --> Cannot read bad block mark: Invalid argument
Thanks
Erik
I have tested on my box version. It is 1.11, so kwboot can not be used. (My box is breakable, so i m extra careful)
Before i start i have one question about the /etc/fw_env.config file;
has the offset to be 0xc0000 --> __nand_correct_data: uncorrectable ECC error
has the offset to be 0x100000 --> Cannot read bad block mark: Invalid argument
Thanks
Erik
|
Re: Problem installing Netgear Stora March 18, 2017 03:03PM |
Admin Registered: 13 years ago Posts: 18,543 |
Erik,
It should be set to 0xc0000. As stated in the instruction.
This error is expected, you can't access this location until after you install new u-boot. Stock u-boot defined envs at a different location.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
It should be set to 0xc0000. As stated in the instruction.
has the offset to be 0xc0000 --> __nand_correct_data: uncorrectable ECC error
This error is expected, you can't access this location until after you install new u-boot. Stock u-boot defined envs at a different location.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Problem installing Netgear Stora March 19, 2017 11:33AM |
Registered: 7 years ago Posts: 36 |
Hi Bodhi,
I have installed the new U-boot.
Box is booting into U-boot - happy that, that works, pfff.
I have copyed all environment-parameters into the new uboot, but i think a lot of them can be skipped and deleted.
I want to have the possibility to boot into old Firmware-redhat-linux and to usb.
Both do not boot.
This are mine uboot-enviroment settings:
This is the bootoutput from putty - old enviroment:
And this is the output van nc:
For the usb-boot thinks look like this:
Output of putty:
Output of nc:
I'm using the 4.4.0 filesystem with kernel.
I have done the (because of the new uboot):
mv uImage --> uImage.netgear
mv uImage.orig uImage
Can you help me?
Thanks
Erik
I have installed the new U-boot.
Box is booting into U-boot - happy that, that works, pfff.
I have copyed all environment-parameters into the new uboot, but i think a lot of them can be skipped and deleted.
I want to have the possibility to boot into old Firmware-redhat-linux and to usb.
Both do not boot.
This are mine uboot-enviroment settings:
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:45:22 -0700) Netgear-MS2110 gcc (Debian 4.9.2-10) 4.9.2 GNU ld (GNU Binutils for Debian) 2.25 Hit any key to stop autoboot: 0 Netgear Stora> Netgear Stora> printenv printenv CASset=min MALLOC_len=1 arcNumber=2743 autoload=no baudrate=115200 bootargs_end=:::DB88FXX81:eth0:none bootargs_root=ubi.mtd=2,2048 root=ubi0:rootfs rootfstype=ubifs init=/linuxrc bootcmd=nand read.e 0x800000 0x100000 0x300000; setenv bootargs $(console) $(bootargs_root); bootm 0x800000 bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb console=console=ttyS0,115200 mtdparts=orion_nand: 0x100000@0(uboot),0xff00000@0x100000(root) device=0:1 devices=usb ide mmc disL2Cache=no disL2Prefetch=yes disaMvPnp=no disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-netgear_stora_ms2000.dtb enaAutoRecovery=no enaCpuStream=no enaDCPref=yes enaICPref=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:00:02:02 eth1mtu=1500 ethact=egiga0 ethaddr=00:50:43:00:02:02 ethprime=egiga1 fw_up=disable hddPowerCtrl=no if_netconsole=ping $serverip image_name=uImage ipaddr=192.168.1.188 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 loadaddr=0x02000000 loads_echo=0 loidaddr=0x02000000 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs nandEcc=1bit nc_ready=1 ncip=192.168.1.195 netbsd_en=no netmask=255.255.255.0 netretry=no partition=nand0,2 pexMode=RC preboot=run preboot_nc preboot_nc=setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi rcvrip=169.254.100.100 rootpath=/MNT/ARM_FS/ sata_dma_mode=yes scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.1.195 setL2CacheWT=yes set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;\ ethmtu=1500 start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=nc stdin=nc stdout=nc ubifs_bootcmd=nand read.e 0x800000 0x100000 0x300000; setenv bootargs $(console) $(bootargs_root); bootm 0x800000 uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb0Mode=host usb_boot=run load_dtb; run load_uimage; if run load_initrd; then bootm 0x800000 0x1100000 0x1c00000; else bootm 0x800000 - 0x1c00000; fi usb_bootcmd=usb start; run usb_init; run usb_set_bootargs; run usb_boot usb_device=0:1 usb_init=setenv test=1 usb_load_uimage=ext2load usb 0:1 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb 0:1 0x1100000 /boot/uInitrd usb_ready_retry=15 usb_root=LABEL=rootfs usb_rootdelay=10 usb_rootfstype=ext2 usb_set_bootargs=setenv bootargs $(console) root=$(usb_root) rootfstype=$(usb_rootfstype) rootdelay=$(usb_rootdelay) vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 4872/131068 bytes Netgear Stora>
This is the bootoutput from putty - old enviroment:
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:45:22 -0700) Netgear-MS2110 SoC: Kirkwood 88F6281_A0 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 PHY reset timed out 88E1116 Initialized on egiga0 Using egiga0 device host 192.168.1.195 is alive Using egiga0 device host 192.168.1.195 is alive Using egiga0 device host 192.168.1.195 is alive Using egiga0 device host 192.168.1.195 is alive Using egiga0 device host 192.168.1.195 is alive Uncompressing Linux............................................................................................................................................................ done, booting the kernel.
And this is the output van nc:
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:45:22 -0700) Netgear-MS2110 gcc (Debian 4.9.2-10) 4.9.2 GNU ld (GNU Binutils for Debian) 2.25 Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x100000, size 0x300000 3145728 bytes read: OK ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-2.6.22.18-Netgear Created: 2010-06-13 23:54:53 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2788728 Bytes = 2.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Starting kernel ...
For the usb-boot thinks look like this:
Output of putty:
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:45:22 -0700) Netgear-MS2110 SoC: Kirkwood 88F6281_A0 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 PHY reset timed out 88E1116 Initialized on egiga0 Using egiga0 device host 192.168.1.195 is alive Using egiga0 device host 192.168.1.195 is alive Using egiga0 device host 192.168.1.195 is alive Using egiga0 device host 192.168.1.195 is alive Using egiga0 device host 192.168.1.195 is alive Uncompressing Linux... done, booting the kernel.
Output of nc:
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:45:22 -0700)
Netgear-MS2110
gcc (Debian 4.9.2-10) 4.9.2
GNU ld (GNU Binutils for Debian) 2.25
Hit any key to stop autoboot: 9
0
Netgear Stora> run usb_bootcmd
run usb_bootcmd
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices...
Use USB retry period from the environment: 15 second(s)
1 Storage Device(s) found
## Error: illegal character '='in variable name "test=1"
loading DTB /boot/dts/kirkwood-netgear_stora_ms2000.dtb ...
11849 bytes read in 918 ms (11.7 KiB/s)
loading uImage ...
3154896 bytes read in 640 ms (4.7 MiB/s)
loading uInitrd ...
7179935 bytes read in 688 ms (10 MiB/s)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-4.4.0-kirkwood-tld-1
Created: 2016-02-19 5:55:25 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3154832 Bytes = 3 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-4.4.0-kirkwood-tld-1
Created: 2016-02-19 7:33:04 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 7179871 Bytes = 6.8 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01c00000
Booting using the fdt blob at 0x1c00000
Starting kernel ...
I'm using the 4.4.0 filesystem with kernel.
I have done the (because of the new uboot):
mv uImage --> uImage.netgear
mv uImage.orig uImage
Can you help me?
Thanks
Erik
|
Re: Problem installing Netgear Stora March 19, 2017 04:33PM |
Admin Registered: 13 years ago Posts: 18,543 |
Erik,
Glad that you have the new u-boot installed!
Netconsole does not output more than what you saw. It always stops at
So try to find the Stora in the network. Are you using DHCP (the 4.4 rootfs default settings for ethernet)?
- ping debian.local
- look for a new IP appear in the router or use scanning app to find such IP.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Glad that you have the new u-boot installed!
Netconsole does not output more than what you saw. It always stops at
Starting kernel ...There is no output after this. Unless you set it up further in Debian.
So try to find the Stora in the network. Are you using DHCP (the 4.4 rootfs default settings for ethernet)?
- ping debian.local
- look for a new IP appear in the router or use scanning app to find such IP.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Problem installing Netgear Stora March 19, 2017 05:22PM |
Registered: 7 years ago Posts: 36 |
Hi Bodhi,
I have also an serial cable (putty on com1) also stops at Starting kernel ...
-1- Should i not get info using serial console, or do i have to set envir parameters for that (stdin/stdout/stderr -- otherwords disable nc?)
-2- I looked at my router. It gives a green v when a ip adress is used. I could not find a not known ip-address. Tryed all the ip-addresses but get not an answer back. I will set a fixed ip-address tomorrow.
-3- Did also the ping
debian.local, ---> ping: unknown host debian.local
debian.priv ---> ping: unknown host debian.priv
debian.lan --> ping: unknown host debian.lan
I think it is not booting at all - i think i have to change something.
Any ideas?
Erik
Edited 1 time(s). Last edit at 03/19/2017 05:25PM by Erik.
I have also an serial cable (putty on com1) also stops at Starting kernel ...
-1- Should i not get info using serial console, or do i have to set envir parameters for that (stdin/stdout/stderr -- otherwords disable nc?)
-2- I looked at my router. It gives a green v when a ip adress is used. I could not find a not known ip-address. Tryed all the ip-addresses but get not an answer back. I will set a fixed ip-address tomorrow.
-3- Did also the ping
debian.local, ---> ping: unknown host debian.local
debian.priv ---> ping: unknown host debian.priv
debian.lan --> ping: unknown host debian.lan
I think it is not booting at all - i think i have to change something.
Any ideas?
Erik
Edited 1 time(s). Last edit at 03/19/2017 05:25PM by Erik.
|
Re: Problem installing Netgear Stora March 19, 2017 06:34PM |
Admin Registered: 13 years ago Posts: 18,543 |
Erik,
If you have serial console then don't use nc. Connect serial console and power up.
Interrupt netconsole and
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
If you have serial console then don't use nc. Connect serial console and power up.
Interrupt netconsole and
setenv preboot saveenv resetLet it boot.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Problem installing Netgear Stora March 20, 2017 04:10AM |
Registered: 7 years ago Posts: 36 |
Hi Bodhi,
Thanks !
I have done:
>>Interrupt netconsole and
>>setenv preboot
>>saveenv
>>reset
>>Let it boot.
I have now all my output again on my serial console !
When i try to boot stock Firmware, it gives:
When i try to boot usb, i get:
These are mine enviroment settings:
I have changed /etc/network/interfaces, to a static ip.
But i can not connect to the ip-adress with putty.
Ping gives: Request timed out.
So i think box is not starting.
(If it was i expetcted a bootlog [......] starting ok, which did not show up !)
Thanks !
I have done:
>>Interrupt netconsole and
>>setenv preboot
>>saveenv
>>reset
>>Let it boot.
I have now all my output again on my serial console !
When i try to boot stock Firmware, it gives:
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:45:22 -0700) Netgear-MS2110 SoC: Kirkwood 88F6281_A0 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 PHY reset timed out 88E1116 Initialized on egiga0 Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x100000, size 0x300000 3145728 bytes read: OK ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-2.6.22.18-Netgear Created: 2010-06-13 23:54:53 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2788728 Bytes = 2.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... Uncompressing Linux............................................................................................................................................................ done, booting the kernel.
When i try to boot usb, i get:
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:45:22 -0700)
Netgear-MS2110
SoC: Kirkwood 88F6281_A0
DRAM: 128 MiB
WARNING: Caches not enabled
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
PHY reset timed out
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
Netgear Stora>
Netgear Stora> run usb_bootcmd
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices...
Use USB retry period from the environment: 15 second(s)
1 Storage Device(s) found
loading DTB /boot/dts/kirkwood-netgear_stora_ms2000.dtb ...
11849 bytes read in 917 ms (11.7 KiB/s)
loading uImage ...
3154896 bytes read in 640 ms (4.7 MiB/s)
loading uInitrd ...
7179935 bytes read in 687 ms (10 MiB/s)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-4.4.0-kirkwood-tld-1
Created: 2016-02-19 5:55:25 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3154832 Bytes = 3 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-4.4.0-kirkwood-tld-1
Created: 2016-02-19 7:33:04 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 7179871 Bytes = 6.8 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01c00000
Booting using the fdt blob at 0x1c00000
Loading Kernel Image ... OK
Loading Ramdisk to 03927000, end 03fffe5f ... OK
Loading Device Tree to 03921000, end 03926e48 ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
These are mine enviroment settings:
Netgear Stora> Netgear Stora> printenv CASset=min MALLOC_len=1 arcNumber=2743 autoload=no baudrate=115200 bootargs=$(console) root=$(usb_root) rootfstype=$(usb_rootfstype) rootdelay=$(usb_rootdelay) bootargs_end=:::DB88FXX81:eth0:none bootargs_root=ubi.mtd=2,2048 root=ubi0:rootfs rootfstype=ubifs init=/linuxrc bootcmd=nand read.e 0x800000 0x100000 0x300000; setenv bootargs $(console) $(bootargs_root); bootm 0x800000 bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb console=console=ttyS0,115200 mtdparts=orion_nand: 0x100000@0(uboot),0xff00000@0x100000(root) device=0:1 devices=usb ide mmc disL2Cache=no disL2Prefetch=yes disaMvPnp=no disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-netgear_stora_ms2000.dtb enaAutoRecovery=no enaCpuStream=no enaDCPref=yes enaICPref=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:00:02:02 eth1mtu=1500 ethact=egiga0 ethaddr=00:50:43:00:02:02 ethprime=egiga1 fw_up=disable hddPowerCtrl=no if_netconsole=ping $serverip image_name=uImage ipaddr=192.168.1.188 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 loadaddr=0x02000000 loads_echo=0 loidaddr=0x02000000 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs nandEcc=1bit nc_ready=1 ncip=192.168.1.195 netbsd_en=no netmask=255.255.255.0 netretry=no partition=nand0,2 pexMode=RC preboot_nc=setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi rcvrip=169.254.100.100 rootpath=/MNT/ARM_FS/ sata_dma_mode=yes scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.1.195 setL2CacheWT=yes set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;\ ethmtu=1500 start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial ubifs_bootcmd=nand read.e 0x800000 0x100000 0x300000; setenv bootargs $(console) $(bootargs_root); bootm 0x800000 uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb0Mode=host usb_boot=run load_dtb; run load_uimage; if run load_initrd; then bootm 0x800000 0x1100000 0x1c00000; else bootm 0x800000 - 0x1c00000; fi usb_bootcmd=usb start; run usb_init; run usb_set_bootargs; run usb_boot usb_device=0:1 usb_init=setenv test usb_load_uimage=ext2load usb 0:1 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb 0:1 0x1100000 /boot/uInitrd usb_ready_retry=15 usb_root=LABEL=rootfs usb_rootdelay=10 usb_rootfstype=ext2 usb_set_bootargs=setenv bootargs $(console) root=$(usb_root) rootfstype=$(usb_rootfstype) rootdelay=$(usb_rootdelay) vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 4952/131068 bytes Netgear Stora>
I have changed /etc/network/interfaces, to a static ip.
But i can not connect to the ip-adress with putty.
Ping gives: Request timed out.
So i think box is not starting.
(If it was i expetcted a bootlog [......] starting ok, which did not show up !)
|
Re: Problem installing Netgear Stora March 20, 2017 06:41AM |
Registered: 7 years ago Posts: 36 |
Hi Bodhi,
If i do:
run scan_disk
setenv bootargs 'rootfstype=ext2 rootdelay=10 root=LABEL=rootfs $(console)'
run bootcmd_exec
then the box starts
I can change the rootdelay in the command from: 10 to $(usb_rootdelay) or to $usb_rootdelay,
than the box starts. Any other change and the box hangs. (Uncompressing Linux... done, booting the kernel. -- and nothing). I have re-entered the values with single and double quotes - no difference.
Here the output when i start with real values...
Any ideas...
If i do:
run scan_disk
setenv bootargs 'rootfstype=ext2 rootdelay=10 root=LABEL=rootfs $(console)'
run bootcmd_exec
then the box starts
I can change the rootdelay in the command from: 10 to $(usb_rootdelay) or to $usb_rootdelay,
than the box starts. Any other change and the box hangs. (Uncompressing Linux... done, booting the kernel. -- and nothing). I have re-entered the values with single and double quotes - no difference.
Here the output when i start with real values...
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:45:22 -0700) Netgear-MS2110 SoC: Kirkwood 88F6281_A0 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 PHY reset timed out 88E1116 Initialized on egiga0 Hit any key to stop autoboot: 0 Netgear Stora> Netgear Stora> Netgear Stora> run scan_disk running scan_disk ... Scan device usb starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found device usb 0:1 1 bytes read in 444 ms (0 Bytes/s) Found bootable drive on usb 0 Netgear Stora> setenv bootargs 'rootfstype=ext2 rootdelay=10 root=LABEL=rootfs $(console)' Netgear Stora> run bootcmd_exec loading uImage ... 3154896 bytes read in 532 ms (5.7 MiB/s) loading uInitrd ... 7179935 bytes read in 687 ms (10 MiB/s) loading DTB /boot/dts/kirkwood-netgear_stora_ms2000.dtb ... 11849 bytes read in 812 ms (13.7 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.4.0-kirkwood-tld-1 Created: 2016-02-19 5:55:25 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3154832 Bytes = 3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.4.0-kirkwood-tld-1 Created: 2016-02-19 7:33:04 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7179871 Bytes = 6.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 03927000, end 03fffe5f ... OK Loading Device Tree to 03921000, end 03926e48 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Debian GNU/Linux 8 debian ttyS0 debian login:
Any ideas...
|
Re: Problem installing Netgear Stora March 20, 2017 09:32AM |
Registered: 7 years ago Posts: 36 |
|
Re: Problem installing Netgear Stora March 20, 2017 12:17PM |
Registered: 7 years ago Posts: 36 |
Hi Bodhi,
if i do a
run scan_disk
run set_bootargs and
run bootcmd_exec
than usb is starting correctly.
FW is not starting. There is a line in console about mtdparts, is this enough?
I tryed run bootcmd....
if i do a
run scan_disk
run set_bootargs and
run bootcmd_exec
than usb is starting correctly.
FW is not starting. There is a line in console about mtdparts, is this enough?
I tryed run bootcmd....
Netgear Stora> printenv CASset=min MALLOC_len=1 arcNumber=2743 autoload=no baudrate=115200 bootargs_end=:::DB88FXX81:eth0:none bootargs_root=ubi.mtd=2,2048 root=ubi0:rootfs rootfstype=ubifs $mtdparts init=/linuxrc bootcmd=nand read.e 0x800000 0x100000 0x300000; setenv bootargs $(console) $(bootargs_root); bootm 0x800000 bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb console=console=ttyS0,115200 mtdparts=orion_nand: 0x100000@0(uboot),0xff00000@0x100000(root) device=0:1 devices=usb ide mmc disL2Cache=no disL2Prefetch=yes disaMvPnp=no disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-netgear_stora_ms2000.dtb enaAutoRecovery=no enaCpuStream=no enaDCPref=yes enaICPref=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:00:02:02 eth1mtu=1500 ethact=egiga0 ethaddr=00:50:43:00:02:02 ethprime=egiga1 fw_up=disable hddPowerCtrl=no if_netconsole=ping $serverip image_name=uImage ipaddr=192.168.1.188 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 loadaddr=0x02000000 loads_echo=0 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs nandEcc=1bit nc_ready=1 ncip=192.168.1.195 netbsd_en=no netmask=255.255.255.0 netretry=no partition=nand0,2 pexMode=RC preboot_nc=setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi rcvrip=169.254.100.100 rootpath=/MNT/ARM_FS/ sata_dma_mode=yes scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.1.195 setL2CacheWT=yes set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;\ ethmtu=1500 start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial ubifs_bootcmd=nand read.e 0x800000 0x100000 0x300000; setenv bootargs $(console) $(bootargs_root); bootm 0x800000 uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb0Mode=host usb_boot=run load_dtb; run load_uimage; if run load_initrd; then bootm 0x800000 0x1100000 0x1c00000; else bootm 0x800000 - 0x1c00000; fi usb_bootcmd=usb start; run usb_init; run usb_set_bootargs; run usb_boot usb_device=0:1 usb_init=setenv test usb_load_uimage=ext2load usb 0:1 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb 0:1 0x1100000 /boot/uInitrd usb_ready_retry=15 usb_root=LABEL=rootfs usb_rootdelay=10 usb_rootfstype=ext2 usb_set_bootargs==setenv bootargs $(console root=LABEL=rootfs rootfstype=ext2 rootdelay=10 $mtdparts vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 4829/131068 bytes
|
Re: Problem installing Netgear Stora March 20, 2017 01:43PM |
Admin Registered: 13 years ago Posts: 18,543 |
Erik,
> if i do a
> run scan_disk
> run set_bootargs and
> run bootcmd_exec
>
> than usb is starting correctly.
Great! meaning you've resolve the problem with the envs.
>
> FW is not starting.
To boot back to stock FW in NAND, further set up is needed.
>There is a line in console abo
> ut mtdparts, is this enough?
The mtdparts should be whatever you had in stock envs before.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> if i do a
> run scan_disk
> run set_bootargs and
> run bootcmd_exec
>
> than usb is starting correctly.
Great! meaning you've resolve the problem with the envs.
>
> FW is not starting.
To boot back to stock FW in NAND, further set up is needed.
>There is a line in console abo
> ut mtdparts, is this enough?
The mtdparts should be whatever you had in stock envs before.
mtdparts=orion_nand: 0x100000@0(uboot),0xff00000@0x100000(root)But the above was not stock u-boot definition, it must have been modified already. Can you find what was mtdparts in stock u-boot?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Problem installing Netgear Stora March 20, 2017 02:40PM |
Registered: 7 years ago Posts: 36 |
Hi Bodi,
I have another stora - looks the same is a version 1.21.
This is the printout of the enviroment.
But so as you see, there is nothing after "console=console=ttyS0,115200"
The only thing i see is this:
So: uboot starts at 0 is 1M in size, uImage, starts at 1M and is 6M in size, Root starts at 7M and is 249M in size.
If i use 0-1M for uboot and rest as root, than are the borders the same. Should work, Why does it not.
I can try without anything, maybe that helps...
Greetings
Erik
I have another stora - looks the same is a version 1.21.
This is the printout of the enviroment.
But so as you see, there is nothing after "console=console=ttyS0,115200"
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: RD-88F6281A LE
U-Boot 1.1.4 (Sep 4 2009 - 09:36:11) Marvell version: 3.4.14
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CEE60
Soc: MV88F6281 Rev 3 (DDR2)
CPU running @ 1000Mhz L2 running @ 333Mhz
SysClock = 333Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 64MB
DRAM CS[1] base 0x04000000 size 64MB
DRAM Total size 128MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB
CRC in Flash: 78abcfd3, Calculated CRC: 78abcfd3
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
Module 0 is RGMII
Module 1 is TDM
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0, egiga1 [PRIME]
Hit any key to stop autoboot: 0
Marvell>>
Marvell>>
Marvell>>
Marvell>>
Marvell>>
Marvell>>
Marvell>>
Marvell>>
Marvell>>
Marvell>> printenv console
console=console=ttyS0,115200
Marvell>> printenv
baudrate=115200
loads_echo=0
ipaddr=10.4.50.165
serverip=10.4.50.5
rootpath=/mnt/ARM_FS/
netmask=255.255.255.0
CASset=min
MALLOC_len=1
ethprime=egiga1
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
ethmtu=1500
eth1addr=00:50:43:00:02:02
eth1mtu=1500
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
nandEcc=1bit
netretry=no
rcvrip=169.254.100.100
loidaddr=0x02000000
autoload=no
bootargs_root=ubi.mtd=2,2048 root=ubi0:rootfs rootfstype=ubifs init=/linuxrc
console=console=ttyS0,115200
mainlineLiNux=no
fw_up=disable
bootcmd=nand read.e 0x800000 0x100000 0x300000; setenv bootargs $(console) $(bootargs_root); bootm 0x800000
ethaddr=C0:3F:0E:B0:F2:91
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
hddPowerCtrl=no
loadaddr=0x02000000
enaAutoRecovery=no
ethact=egiga1
The only thing i see is this:
Creating 3 MTD partitions on "nand_mtd": 0x00000000-0x00100000 : "u-boot" 0x00100000-0x00700000 : "uImage" 0x00700000-0x10000000 : "root"
So: uboot starts at 0 is 1M in size, uImage, starts at 1M and is 6M in size, Root starts at 7M and is 249M in size.
If i use 0-1M for uboot and rest as root, than are the borders the same. Should work, Why does it not.
I can try without anything, maybe that helps...
Greetings
Erik
|
Re: Problem installing Netgear Stora March 20, 2017 06:38PM |
Admin Registered: 13 years ago Posts: 18,543 |
Erik Wrote:
-------------------------------------------------------
> Hi Bodi,
>
> I have another stora - looks the same is a version
> 1.21.
> This is the printout of the enviroment.
> But so as you see, there is nothing after "console
> =console=ttyS0,115200"
>
>
> The only thing i see is this:
>
> So: uboot starts at 0 is 1M in size, uImage, start
> s at 1M and is 6M in size, Root starts at 7M and i
> s 249M in size.
> If i use 0-1M for uboot and rest as root, than are
> the borders the same. Should work, Why does it not
> .
>
> I can try without anything, maybe that helps...
>
> Greetings
>
> Erik
Yes. Your calculation is correct. It should work.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> Hi Bodi,
>
> I have another stora - looks the same is a version
> 1.21.
> This is the printout of the enviroment.
> But so as you see, there is nothing after "console
> =console=ttyS0,115200"
>
>
> __ __ _ _ > | \/ | __ _ _ ____ _____| | | > | |\/| |/ _` | '__\ \ / / _ \ | | > | | | | (_| | | \ V / __/ | | > |_| |_|\__,_|_| \_/ \___|_|_| > _ _ ____ _ > | | | | | __ ) ___ ___ | |_ > | | | |___| _ \ / _ \ / _ \| __| > | |_| |___| |_) | (_) | (_) | |_ > \___/ |____/ \___/ \___/ \__| > ** MARVELL BOARD: RD-88F6281A LE > > U-Boot 1.1.4 (Sep 4 2009 - 09:36:11) Marvell vers > ion: 3.4.14 > > U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CEE6 > 0 > > Soc: MV88F6281 Rev 3 (DDR2) > CPU running @ 1000Mhz L2 running @ 333Mhz > SysClock = 333Mhz , TClock = 200Mhz > > DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 > DRAM CS[0] base 0x00000000 size 64MB > DRAM CS[1] base 0x04000000 size 64MB > DRAM Total size 128MB 16bit width > Flash: 0 kB > Addresses 8M - 0M are saved for the U-Boot usage. > Mem malloc Initialization (8M - 7M): Done > NAND:256 MB > CRC in Flash: 78abcfd3, Calculated CRC: 78abcfd3 > > CPU : Marvell Feroceon (Rev 1) > > Streaming disabled > Write allocate disabled > > Module 0 is RGMII > Module 1 is TDM > > USB 0: host mode > PEX 0: interface detected no Link. > Net: egiga0, egiga1 [PRIME] > Hit any key to stop autoboot: 0 > Marvell>> > Marvell>> > Marvell>> > Marvell>> > Marvell>> > Marvell>> > Marvell>> > Marvell>> > Marvell>> > Marvell>> printenv console > console=console=ttyS0,115200 > Marvell>> printenv > baudrate=115200 > loads_echo=0 > ipaddr=10.4.50.165 > serverip=10.4.50.5 > rootpath=/mnt/ARM_FS/ > netmask=255.255.255.0 > CASset=min > MALLOC_len=1 > ethprime=egiga1 > bootargs_end=:::DB88FXX81:eth0:none > image_name=uImage > standalone=fsload 0x2000000 $(image_name);setenv b > ootargs $(console) root=/dev/mtdblock0 rw ip=$(ipa > ddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); > bootm 0x2000000; > ethmtu=1500 > eth1addr=00:50:43:00:02:02 > eth1mtu=1500 > mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs > mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2 > :3),mtu=1500 > usb0Mode=host > yuk_ethaddr=00:00:00:EE:51:81 > nandEcc=1bit > netretry=no > rcvrip=169.254.100.100 > loidaddr=0x02000000 > autoload=no > bootargs_root=ubi.mtd=2,2048 root=ubi0:rootfs root > fstype=ubifs init=/linuxrc > console=console=ttyS0,115200 > mainlineLiNux=no > fw_up=disable > bootcmd=nand read.e 0x800000 0x100000 0x300000; se > tenv bootargs $(console) $(bootargs_root); bootm 0 > x800000 > ethaddr=C0:3F:0E:B0:F2:91 > stdin=serial > stdout=serial > stderr=serial > mainlineLinux=no > enaMonExt=no > enaCpuStream=no > enaWrAllo=no > pexMode=RC > disL2Cache=no > setL2CacheWT=yes > disL2Prefetch=yes > enaICPref=yes > enaDCPref=yes > sata_dma_mode=yes > netbsd_en=no > vxworks_en=no > bootdelay=3 > disaMvPnp=no > hddPowerCtrl=no > loadaddr=0x02000000 > enaAutoRecovery=no > ethact=egiga1 > > >>
> The only thing i see is this:
>
> Creating 3 MTD partitions on "nand_mtd": > 0x00000000-0x00100000 : "u-boot" > 0x00100000-0x00700000 : "uImage" > 0x00700000-0x10000000 : "root" > >>
> So: uboot starts at 0 is 1M in size, uImage, start
> s at 1M and is 6M in size, Root starts at 7M and i
> s 249M in size.
> If i use 0-1M for uboot and rest as root, than are
> the borders the same. Should work, Why does it not
> .
>
> I can try without anything, maybe that helps...
>
> Greetings
>
> Erik
Yes. Your calculation is correct. It should work.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Problem installing Netgear Stora March 23, 2017 02:21PM |
Registered: 7 years ago Posts: 36 |
Hi Bodhi,
I tryed to get old firmware started, with different mdtparts, without, different configs, with and without old uboot params, but after decompressing it is not working. There are plenty of errors where the booting can stop and because i don't know the errors - nothing is reported to the console - the changes are slim to get it started.
So i want to replace existing md1/md2 partitions and fill this with a working version of linux.
So i'm currious if there is a build kernel and filesystem for in the nand. Do you know and were to find Howto.
Can i use the rescue system for this and is het tested on netgear stora
Thanks verry much for the info
Erik
I tryed to get old firmware started, with different mdtparts, without, different configs, with and without old uboot params, but after decompressing it is not working. There are plenty of errors where the booting can stop and because i don't know the errors - nothing is reported to the console - the changes are slim to get it started.
So i want to replace existing md1/md2 partitions and fill this with a working version of linux.
So i'm currious if there is a build kernel and filesystem for in the nand. Do you know and were to find Howto.
Can i use the rescue system for this and is het tested on netgear stora
Thanks verry much for the info
Erik
|
Re: Problem installing Netgear Stora March 23, 2017 03:35PM |
Admin Registered: 13 years ago Posts: 18,543 |
Erik,
> I tryed to get old firmware started, with differen
> t mdtparts, without, different configs, with and w
> ithout old uboot params, but after decompressing i
> t is not working. There are plenty of errors where
> the booting can stop and because i don't know the
> errors - nothing is reported to the console - the
> changes are slim to get it started.
I would suggest that you back up all the mtds. In case you want to try to go back to stock later to use it as rescue system, or if you want to sell the box.
>
> So i want to replace existing md1/md2 partitions a
> nd fill this with a working version of linux.
> So i'm currious if there is a build kernel and fil
> esystem for in the nand. Do you know and were to f
> ind Howto.
>
> Can i use the rescue system for this and is het te
> sted on netgear stora
>
Is your purpose just a rescue system (to fall back in case the rootfs is corrupted and box will boot into that system).
The rescue system from Jeff/davygravy has not been tested on the Stora. I would have to refresh my memory about the Stora to say if it might work or not :)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> I tryed to get old firmware started, with differen
> t mdtparts, without, different configs, with and w
> ithout old uboot params, but after decompressing i
> t is not working. There are plenty of errors where
> the booting can stop and because i don't know the
> errors - nothing is reported to the console - the
> changes are slim to get it started.
I would suggest that you back up all the mtds. In case you want to try to go back to stock later to use it as rescue system, or if you want to sell the box.
>
> So i want to replace existing md1/md2 partitions a
> nd fill this with a working version of linux.
> So i'm currious if there is a build kernel and fil
> esystem for in the nand. Do you know and were to f
> ind Howto.
>
> Can i use the rescue system for this and is het te
> sted on netgear stora
>
Is your purpose just a rescue system (to fall back in case the rootfs is corrupted and box will boot into that system).
The rescue system from Jeff/davygravy has not been tested on the Stora. I would have to refresh my memory about the Stora to say if it might work or not :)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Problem installing Netgear Stora March 26, 2017 10:20AM |
Registered: 7 years ago Posts: 36 |
Hi Bodhi,
I think thats a great idea to backup first the mtd's.
So i did follow your advise.
I gues this is because, the ubifs is not completely filled, so dump stops(?) (reading only FF or ), when nandwrite sees un-used blocks i think.
I don't know if this is causing problems - when restoring mtd's , for other people, so i just want to tell it. - i have not tested if the mtd-dumps are working !
Erik
Edited 1 time(s). Last edit at 03/26/2017 10:37AM by Erik.
I think thats a great idea to backup first the mtd's.
So i did follow your advise.
root@debian:~# nanddump --noecc --omitoob -l 0x80000 -f mtd0 /dev/mtd0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x00080000... root@debian:~# nanddump --noecc --omitoob -s 0x100000 -l 0x600000 -f mtd1 /dev/mtd1 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00100000 and ending at 0x00600000... >> He, the length should be 0x0600000 and not the ending >> Then i make the length address the ending address root@debian:~# nanddump --noecc --omitoob -s 0x0100000 -l 0x0700000 -f mtd1 /dev/mtd1 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00100000 and ending at 0x00600000... >>The same. But maybe this is not a problem the bootimage is only 2.7Mb root@debian:~# nanddump --noecc --omitoob -s 0x700000 -l 0xf900000 -f mtd2 /dev/mtd2 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00700000 and ending at 0x0f900000... Also with mtd2... >> He, the end should be 10000000 nanddump --noecc --omitoob -s 0x700000 -l 0x10000000 -f mtd2 /dev/mtd2 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00700000 and ending at 0x0f900000... He?? But also here; mine rootfs has a size of 212Mb and USed is 168Mb, Avail is 44M. So also here this looks OK.
I gues this is because, the ubifs is not completely filled, so dump stops(?) (reading only FF or ), when nandwrite sees un-used blocks i think.
I don't know if this is causing problems - when restoring mtd's , for other people, so i just want to tell it. - i have not tested if the mtd-dumps are working !
Erik
Edited 1 time(s). Last edit at 03/26/2017 10:37AM by Erik.
|
Re: Problem installing Netgear Stora March 26, 2017 04:22PM |
Admin Registered: 13 years ago Posts: 18,543 |
Erik
Dont use the length when dumpnign the entire mtd. So use this format for each mtd
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Dont use the length when dumpnign the entire mtd. So use this format for each mtd
nanddump --noecc --omitoob -f mtd0 /dev/mtd0
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Problem installing Netgear Stora March 28, 2017 12:31PM |
Registered: 7 years ago Posts: 36 |
Bodhi,
Thanks !!!
Your quite right.
After -not using the -l -argument i get, when copying:
So thanks again.
Erik
Thanks !!!
Your quite right.
After -not using the -l -argument i get, when copying:
mtd0-stora1 100% 1024KB 1.0MB/s 00:00 mtd0-stora2 100% 1024KB 1.0MB/s 00:00 mtd1-stora1 100% 6144KB 3.0MB/s 00:02 mtd1-stora2 100% 6144KB 3.0MB/s 00:02 mtd2-stora1 100% 248MB 4.0MB/s 01:02 mtd2-stora2 100% 248MB 4.1MB/s 01:01 -rwxrwxrwx 1 apache users 1.0M Mar 28 18:54 mtd0-stora1 -rwxrwxrwx 1 apache users 1.0M Mar 28 19:10 mtd0-stora2 -rwxrwxrwx 1 apache users 6.0M Mar 28 18:54 mtd1-stora1 -rwxrwxrwx 1 apache users 6.0M Mar 28 19:10 mtd1-stora2 -rwxrwxrwx 1 apache users 248M Mar 28 18:57 mtd2-stora1 -rwxrwxrwx 1 apache users 248M Mar 28 19:13 mtd2-stora2
So thanks again.
Erik
|
Re: Problem installing Netgear Stora April 02, 2017 04:40PM |
Registered: 7 years ago Posts: 36 |
Hi Bodhi,
I want to try to put a new kernel in filesystem in mtd
I have mtd1 for uImage and mtd2 for filesystem
So i can do 2 things
1- make a new filesystem mtd1 for the total size of 249+6Mb and put a filesystem in with uImage and uInit and dtsfile. But than i have to load the files from the ubifs filesystem. I have to mount the ubifs rootfs and than load the 3 files. Do you have any experience with this. I'm trying this but i get:
>> ubifsload ubi0:rootfs 0x800000 /boot/uImage >>> mount filesystem first
>> mtdparts
>> ubi part rootfs
>> mount ubi0:rootfs >>> does not do the job.
2 - make on file containing uImage, UInitrd and dts-file in mtd1 and do a nand read.e
Do you know how to make 1 file of this 3 files?
Thanks
Erik
I want to try to put a new kernel in filesystem in mtd
I have mtd1 for uImage and mtd2 for filesystem
So i can do 2 things
1- make a new filesystem mtd1 for the total size of 249+6Mb and put a filesystem in with uImage and uInit and dtsfile. But than i have to load the files from the ubifs filesystem. I have to mount the ubifs rootfs and than load the 3 files. Do you have any experience with this. I'm trying this but i get:
>> ubifsload ubi0:rootfs 0x800000 /boot/uImage >>> mount filesystem first
>> mtdparts
>> ubi part rootfs
>> mount ubi0:rootfs >>> does not do the job.
2 - make on file containing uImage, UInitrd and dts-file in mtd1 and do a nand read.e
Do you know how to make 1 file of this 3 files?
Thanks
Erik
|
Re: Problem installing Netgear Stora April 02, 2017 06:10PM |
Admin Registered: 13 years ago Posts: 18,543 |
Hi Erik,
I usually like to discourage people to put the kernel files and rootfs in NAND, because it's really uneccessary. And rootfs in NAND is not useful, due to limited NAND space, and lack of security upgrade. You are not going to run security updates too often if the rootfs is in NAND (wear it out really fast).
With that said, everyone has own needs :) So here how you can put all these kernel files in one image using mkimage with a multi-image option.
And use man mkimage command to see explanation further.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
I usually like to discourage people to put the kernel files and rootfs in NAND, because it's really uneccessary. And rootfs in NAND is not useful, due to limited NAND space, and lack of security upgrade. You are not going to run security updates too often if the rootfs is in NAND (wear it out really fast).
With that said, everyone has own needs :) So here how you can put all these kernel files in one image using mkimage with a multi-image option.
mkimage -T multi .......
And use man mkimage command to see explanation further.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Daniel
Re: Problem installing Netgear Stora October 10, 2019 04:03AM |
