Pogoplug v4 usb image April 22, 2017 02:09PM |
Registered: 6 years ago Posts: 21 |
Re: Pogoplug v4 usb image April 22, 2017 04:24PM |
Admin Registered: 13 years ago Posts: 18,550 |
Quote
Updated 20 Feb 2016:
This Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 is to keep in sync with kernel Linux-4.4.0-kirkwood-tld-1.
Basic minimal Debian Kirkwood rootfs for most Kirwood plugs:
Re: Pogoplug v4 usb image April 22, 2017 11:57PM |
Registered: 6 years ago Posts: 21 |
Re: Pogoplug v4 usb image April 23, 2017 09:50AM |
Registered: 6 years ago Posts: 21 |
U-Boot 1.1.4 (Oct 1 2011 - 12:21:35) Cloud Engines 1.1.2 (3.4.27) PHYADDR=0 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006918B4 Soc: 88F6192 A1 (DDR2) CPU running @ 800Mhz L2 running @ 400Mhz SysClock = 200Mhz , TClock = 166Mhz DRAM CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB Flash: 0 kB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: PPV4A1 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x100000, size 0x73d0c 474380 bytes read: OK ## Starting application at 0x00800000 ... U-Boot 1.1.4 (Jan 13 2012 - 22:33:21) Arch Linux ARM (PPV4 r1) PHYADDR=0 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFD60 Soc: 88F6192 A1 (DDR2) CPU running @ 800Mhz L2 running @ 400Mhz SysClock = 200Mhz , TClock = 166Mhz DRAM CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB Flash: 0 kB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: PPV4A1 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 (Re)start USB... USB: scanning bus for devices... 2 USB Device(s) found Waiting for storage device(s) to settle before scanning... 1 Storage Device(s) found Reset IDE: Marvell Serial ATA Adapter Integrated Sata device found No Fat FS detected IDE device 0 not available .... ................................................................................ ................................................................................ ................................................................................ ............................................................... 3154896 bytes read ## Booting image at 00800000 ... Image Name: Linux-4.4.0-kirkwood-tld-1 Created: 2016-02-19 5:55:25 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3154832 Bytes = 3 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Error: unrecognized/unsupported machine ID (r1 = 0x00000f78). Available machine support: ID (hex) NAME ffffffff Generic DT based system ffffffff Marvell Kirkwood (Flattened Device Tree) Please check your kernel config and/or bootloader.
Re: Pogoplug v4 usb image April 23, 2017 02:57PM |
Registered: 6 years ago Posts: 21 |
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFD60 Soc: 88F6192 A1 (DDR2) CPU running @ 800Mhz L2 running @ 400Mhz SysClock = 200Mhz , TClock = 166Mhz DRAM CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB Flash: 0 kB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: PPV4A1 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 (Re)start USB... USB: scanning bus for devices... 4 USB Device(s) found Waiting for storage device(s) to settle before scanning... 2 Storage Device(s) found Reset IDE: Marvell Serial ATA Adapter Integrated Sata device found No Fat FS detected IDE device 0 not available .... ................................................................................................................................................................................................................................................................................................................ 3166793 bytes read ## Booting image at 00800000 ... Image Name: Linux-4.4.0-kirkwood-tld-1 Created: 2017-04-23 19:22:56 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3166729 Bytes = 3 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine model: Seagate GoFlex Net [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootwait rootfstype=ext3 [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 120632K/131072K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 10440K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc07d7ef4 (8000 kB) [ 0.000000] .init : 0xc07d8000 - 0xc0822000 ( 296 kB) [ 0.000000] .data : 0xc0822000 - 0xc08b169c ( 574 kB) [ 0.000000] .bss : 0xc08b169c - 0xc08ff9d0 ( 313 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns [ 0.000013] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns [ 0.000478] Console: colour dummy device 80x30 [ 0.000521] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216) [ 0.090127] pid_max: default: 32768 minimum: 301 [ 0.090287] Security Framework initialized [ 0.090398] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090428] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.091609] Initializing cgroup subsys io [ 0.091659] Initializing cgroup subsys devices [ 0.091698] Initializing cgroup subsys freezer [ 0.091746] Initializing cgroup subsys net_cls [ 0.091870] CPU: Testing write buffer coherency: ok [ 0.092534] Setting up static identity map for 0x8200 - 0x8258 [ 0.092973] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.098373] devtmpfs: initialized [ 0.106077] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.106750] prandom: seed boundary self test passed [ 0.112465] prandom: 100 self tests passed [ 0.112521] pinctrl core: initialized pinctrl subsystem [ 0.114590] NET: Registered protocol family 16 [ 0.115289] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.140152] cpuidle: using governor ladder [ 0.170149] cpuidle: using governor menu [ 0.170760] Feroceon L2: Enabling L2 [ 0.170821] Feroceon L2: Cache support initialised. [ 0.171367] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.178769] No ATAGs? [ 0.212255] vgaarb: loaded [ 0.212806] usbcore: registered new interface driver usbfs [ 0.212926] usbcore: registered new interface driver hub [ 0.213045] usbcore: registered new device driver usb [ 0.214635] clocksource: Switched to clocksource orion_clocksource [ 0.296271] NET: Registered protocol family 2 [ 0.297442] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.297481] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.297512] TCP: Hash tables configured (established 1024 bind 1024) [ 0.297615] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.297650] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.297931] NET: Registered protocol family 1 [ 0.298499] RPC: Registered named UNIX socket transport module. [ 0.298516] RPC: Registered udp transport module. [ 0.298527] RPC: Registered tcp transport module. [ 0.298538] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.299077] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.300591] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.300693] audit: initializing netlink subsys (disabled) [ 0.300764] audit: type=2000 audit(0.290:1): initialized [ 0.301268] Initialise system trusted keyring [ 0.301780] zbud: loaded [ 0.302200] VFS: Disk quotas dquot_6.6.0 [ 0.302287] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.303076] NFS: Registering the id_resolver key type [ 0.303161] Key type id_resolver registered [ 0.303174] Key type id_legacy registered [ 0.303211] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.303232] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.303558] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.304285] Key type big_key registered [ 0.320877] Key type asymmetric registered [ 0.320909] Asymmetric key parser 'x509' registered [ 0.321040] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.321070] io scheduler noop registered [ 0.321093] io scheduler deadline registered [ 0.321179] io scheduler cfq registered (default) [ 0.323088] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 0.324074] irq: Cannot allocate irq_descs @ IRQ33, assuming pre-allocated [ 0.324861] irq: Cannot allocate irq_descs @ IRQ65, assuming pre-allocated [ 0.325669] mv_xor f1060800.xor: Marvell shared XOR driver [ 0.365644] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 0.365991] mv_xor f1060900.xor: Marvell shared XOR driver [ 0.405645] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 0.406376] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.408435] console [ttyS0] disabled [ 0.408520] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 10416666) is a 16550A [ 0.989287] console [ttyS0] enabled [ 0.994757] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 1.001088] nand: Hynix H27U1G8F2BTR-BC [ 1.004945] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.012498] Scanning device for bad blocks [ 1.116605] libphy: Fixed MDIO Bus: probed [ 1.121141] libphy: orion_mdio_bus: probed [ 1.126312] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 2.202866] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:05:86:37 [ 2.211789] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.218359] ehci-pci: EHCI PCI platform driver [ 2.222885] ehci-orion: EHCI orion driver [ 2.227162] orion-ehci f1050000.ehci: EHCI Host Controller [ 2.232662] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 2.240609] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 2.264678] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 2.270978] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.277783] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.285004] usb usb1: Product: EHCI Host Controller [ 2.289869] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd [ 2.296486] usb usb1: SerialNumber: f1050000.ehci [ 2.302238] hub 1-0:1.0: USB hub found [ 2.306098] hub 1-0:1.0: 1 port detected [ 2.311397] mousedev: PS/2 mouse device common for all mice [ 2.624680] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 2.777366] usb 1-1: New USB device found, idVendor=05e3, idProduct=0610 [ 2.784060] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.791218] usb 1-1: Product: USB2.0 Hub [ 2.795152] usb 1-1: Manufacturer: GenesysLogic [ 2.801077] hub 1-1:1.0: USB hub found [ 2.805367] hub 1-1:1.0: 4 ports detected [ 3.084671] usb 1-1.1: new high-speed USB device number 3 using orion-ehci [ 3.196992] usb 1-1.1: New USB device found, idVendor=154b, idProduct=007a [ 3.203860] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.211189] usb 1-1.1: Product: USB 2.0 FD [ 3.215299] usb 1-1.1: Manufacturer: PNY Technologies [ 3.220336] usb 1-1.1: SerialNumber: 0416KK00000000001744 [ 3.304670] usb 1-1.2: new high-speed USB device number 4 using orion-ehci [ 3.324668] rtc-mv f1010300.rtc: internal RTC not ticking [ 3.330388] i2c /dev entries driver [ 3.337840] hidraw: raw HID events driver (C) Jiri Kosina [ 3.343800] drop_monitor: Initializing network drop monitor service [ 3.350482] NET: Registered protocol family 17 [ 3.355317] Key type dns_resolver registered [ 3.360752] registered taskstats version 1 [ 3.364952] Loading compiled-in X.509 certificates [ 3.369829] zswap: loaded using pool lzo/zbud [ 3.375785] Key type encrypted registered [ 3.380438] hctosys: unable to open rtc device (rtc0) [ 3.387768] Waiting for root device /dev/sda1... [ 3.428376] usb 1-1.2: New USB device found, idVendor=04fc, idProduct=0c15 [ 3.435276] usb 1-1.2: New USB device strings: Mfr=2, Product=3, SerialNumber=1 [ 3.442587] usb 1-1.2: Product: USB to Serial-ATA bridge [ 3.447905] usb 1-1.2: Manufacturer: Sunplus Technology Inc. [ 3.453548] usb 1-1.2: SerialNumber: ST9500420A5VJ2TG0N [ 127.171733] random: nonblocking pool is initialized
Re: Pogoplug v4 usb image April 23, 2017 04:10PM |
Admin Registered: 13 years ago Posts: 18,550 |
3166793 bytes read ## Booting image at 00800000 ... Image Name: Linux-4.4.0-kirkwood-tld-1 Created: 2017-04-23 19:22:56 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3166729 Bytes = 3 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ...
printenv
Re: Pogoplug v4 usb image April 23, 2017 05:21PM |
Registered: 6 years ago Posts: 21 |
Re: Pogoplug v4 usb image April 23, 2017 05:37PM |
Registered: 6 years ago Posts: 21 |
CE>> printenv baudrate=115200 loads_echo=0 ipaddr=169.254.254.253 serverip=169.254.254.254 rootpath=/mnt/ARM_FS/ netmask=255.255.0.0 run_diag=yes stdin=serial stdout=serial stderr=serial mainlineLinux=no CASset=min enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes MALLOC_len=1 ethprime=egiga0 netbsd_en=no vxworks_en=no load_nand=nboot 0x800000 0 0x200000 load_nand2=nboot 0x800000 0 0x500000 boot=bootm 0x800000 boot_nand=run load_nand boot || run load_nand2 boot bootcmd=run boot_nand bootargs=console=ttyS0,115200 root=ubi0:rootfs ubi.mtd=4,2048 rootfstype=ubifs ceboardver=PPV4A1 bootdelay=1 disaMvPnp=no ethaddr=00:50:43:00:02:02 ethmtu=1500 usb0Mode=host nandEcc=1bit hddPowerCtrl=no pcieTune=no ethact=egiga0 Environment size: 801/131068 bytes
Re: Pogoplug v4 usb image April 23, 2017 06:40PM |
Admin Registered: 13 years ago Posts: 18,550 |
Re: Pogoplug v4 usb image April 23, 2017 06:48PM |
Registered: 6 years ago Posts: 21 |
Re: Pogoplug v4 usb image April 23, 2017 09:46PM |
Admin Registered: 13 years ago Posts: 18,550 |
Set envs in stock Pogoplug V4 u-boot to boot USB Debian rootfs April 24, 2017 12:18AM |
Admin Registered: 13 years ago Posts: 18,550 |
setenv arcNumber '3960' setenv machid 'F78' setenv load_initrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd' setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' setenv mainlineLinux 'yes' setenv mtdids 'nand0=orion_nand' setenv mtdparts 'mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)' setenv partition 'nand0,2' setenv set_bootargs 'setenv bootargs "console=$(console) root=LABEL=rootfs rootdelay=10 $(mtdparts) $(custom_params)"' setenv bootcmd_exec 'mw 0x800000 0 1; load_uimage; run load_initrd; bootm 0x800000 0x1100000' setenv bootcmd 'run set_bootargs; run bootcmd_exec; reset' boot
Re: Pogoplug v4 usb image April 25, 2017 01:41AM |
Registered: 6 years ago Posts: 21 |
CE>> printenv baudrate=115200 loads_echo=0 ipaddr=169.254.254.253 serverip=169.254.254.254 rootpath=/mnt/ARM_FS/ netmask=255.255.0.0 run_diag=yes stdin=serial stdout=serial stderr=serial CASset=min enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes MALLOC_len=1 ethprime=egiga0 netbsd_en=no vxworks_en=no load_nand=nboot 0x800000 0 0x200000 load_nand2=nboot 0x800000 0 0x500000 boot=bootm 0x800000 boot_nand=run load_nand boot || run load_nand2 boot bootargs=console=ttyS0,115200 root=ubi0:rootfs ubi.mtd=4,2048 rootfstype=ubifs ceboardver=PPV4A1 bootdelay=1 disaMvPnp=no ethaddr=00:50:43:00:02:02 ethmtu=1500 usb0Mode=host nandEcc=1bit hddPowerCtrl=no pcieTune=no ethact=egiga0 arcNumber=3960 machid=F78 load_initrd=ext2load usb 0:1 0x1100000 /boot/uInitrd load_uimage=ext2load usb 0:1 0x800000 /boot/uImage mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) partition=nand0,2 set_bootargs=setenv bootargs "console=$(console) root=LABEL=rootfs rootdelay=10 $(mtdparts) $(custom_params)" bootcmd_exec=mw 0x800000 0 1; load_uimage; run load_initrd; bootm 0x800000 0x1100000 bootcmd=run set_bootargs; run bootcmd_exec; reset Environment size: 1284/131068 bytes CE>>
Re: Pogoplug v4 usb image April 26, 2017 06:56PM |
Registered: 6 years ago Posts: 21 |
Re: Pogoplug v4 usb image April 26, 2017 08:39PM |
Admin Registered: 13 years ago Posts: 18,550 |
Re: Pogoplug v4 usb image April 27, 2017 11:00AM |
Registered: 6 years ago Posts: 21 |
U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 No link on egiga0 Wrong Image Format for bootm command ERROR: can't get kernel image! Pogov4>
Pogov4> printenv arcNumber=3960 baudrate=115200 bootargs=root=/dev/nfs nfsroot=192.168.1.100: ip=192.168.1.10:192.168.1.100:::::off bootcmd=bootp; setenv bootargs root=/dev/nfs nfsroot=${serverip}:${rootpath} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; bootm bootdelay=5 ethact=egiga0 ethaddr=00:50:43:00:02:02 if_netconsole=ping $serverip ipaddr=192.168.1.10 machid=F78 mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) serverip=192.168.1.100 stderr=serial stdin=serial stdout=serial usb_rootfstype=ext3this doesn't look complete to me
Re: Pogoplug v4 usb image April 27, 2017 05:29PM |
Admin Registered: 13 years ago Posts: 18,550 |
> U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45) > Pogoplug V4 > > SoC: Kirkwood 88F6192_A1 > DRAM: 128 MiB > WARNING: Caches not enabled > NAND: 128 MiB > MMC: kwsdio: 0 > In: serial > Out: serial > Err: serial > Net: egiga0 > Hit any key to stop autoboot: 0 > No link on egiga0 > Wrong Image Format for bootm command > ERROR: can't get kernel image! > Pogov4> > >>
> Pogov4> printenv > arcNumber=3960 > baudrate=115200 > bootargs=root=/dev/nfs nfsroot=192.168.1.100: ip=1 > 92.168.1.10:192.168.1.100:::::off > bootcmd=bootp; setenv bootargs root=/dev/nfs nfsro > ot=${serverip}:${rootpath} ip=${ipaddr}:${serverip > }:${gatewayip}:${netmask}:${hostname}::off; bootm > bootdelay=5 > ethact=egiga0 > ethaddr=00:50:43:00:02:02 > if_netconsole=ping $serverip > ipaddr=192.168.1.10 > machid=F78 > mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage) > ,3M(uImage2),8M(failsafe),112M(root) > serverip=192.168.1.100 > stderr=serial > stdin=serial > stdout=serial > usb_rootfstype=ext3 >> this doesn't look complete to me
Re: Pogoplug v4 usb image April 27, 2017 05:38PM |
Registered: 6 years ago Posts: 21 |
Re: Pogoplug v4 usb image April 27, 2017 05:47PM |
Admin Registered: 13 years ago Posts: 18,550 |
Re: Pogoplug v4 usb image April 27, 2017 05:59PM |
Registered: 6 years ago Posts: 21 |
U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 Unknown command 'load_uimage' - try 'help' ** Bad device usb 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! resetting ... U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 Pogov4> biit Unknown command 'biit' - try 'help' Pogov4> boot Unknown command 'load_uimage' - try 'help' ** Bad device usb 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! resetting ...
Re: Pogoplug v4 usb image April 27, 2017 11:55PM |
Registered: 6 years ago Posts: 21 |
Pogov4> printenv CASset=min MALLOC_len=1 arcNumber=3960 baudrate=115200 boot=bootm 0x800000 boot_nand=run load_nand boot bootargs=console $(console) root LABEL rootfs rootdelay 10 $(mtdparts) $(custom_params) bootargs_console=console=ttyS0,115200 bootcmd=run set_bootargs; run bootcmd_exec; reset bootcmd_exec=mw 0x800000 0 1 bootcmd_mmc=mmc init; ext2load mmc 0:1 0x00800000 /uImage; ext2load mmc 0:1 0x01100000 /uInitrd bootcmd_usb=usb start; ext2load usb 0:1 0x00800000 /uImage; ext2load usb 0:1 0x01100000 /uInitrd bootdelay=3 bootfile=u-boot.bin ceboardver=PPV4A1 disL2Cache=no disL2Prefetch=yes disaMvPnp=no enaCpuStream=no enaDCPref=yes enaICPref=yes enaMonExt=no enaWrAllo=no ethact=egiga0 ethaddr=00:25:31:05:86:37 ethmtu=1500 ethprime=egiga0 hddPowerCtrl=no ipaddr=10.0.0.117 load_initd=ext2load usb 0:1 0x1100000 /boot/uInitrd load_initrd=ext2load usb 0:1 0x1100000 /boot/uInitrd load_nand=nboot 0x800000 0 0x200000 load_nand2=nboot 0x800000 0 0x500000 load_uimad=usb 0:1 0x800000 /boot/uImage\ setenv mainlineLinux yes\ setenv mtdids nand0=orion_nand\ setenv mtdparts mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)\ setenv partition nand0,2\ setenv set_bootargs setenv bootargs console=$(console) root=LABEL=rootfs rootdelay=10 $(mtdparts) $(custom_params)\ setenv bootcmd_exec mw 0x800000 0 1 load_uimage=ext2load usb 0:1 0x800000 /boot/uImage loads_echo=0 machid=F78 mainlineLinux=yes mtdids=nand0 orion_nand mtdparts=mtdparts orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) nandEcc=1bit netbsd_en=no netmask=255.255.255.0 pcieTune=no pexMode=RC rootpath=t/ARM_FS/ run_diag=yes sata_dma_mode=yes serverip=10.0.0.43 setL2CacheWT=yes set_bootargs=setenv bootargs console $(console) root LABEL rootfs rootdelay 10 $(mtdparts) $(custom_params) stderr=serial stdin=serial stdout=serial usb0Mode=host vxworks_en=no Environment size: 1962/131068 bytes
U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 Pogov4>
Re: Pogoplug v4 usb image April 28, 2017 12:05AM |
Registered: 6 years ago Posts: 21 |
Re: Pogoplug v4 usb image April 28, 2017 12:26AM |
Admin Registered: 13 years ago Posts: 18,550 |
> > Pogov4> printenv > CASset=min > MALLOC_len=1 > arcNumber=3960 > baudrate=115200 > boot=bootm 0x800000 > boot_nand=run load_nand boot > bootargs=console $(console) root LABEL rootfs root > delay 10 $(mtdparts) $(custom_params) > bootargs_console=console=ttyS0,115200 > bootcmd=run set_bootargs; run bootcmd_exec; reset > bootcmd_exec=mw 0x800000 0 1 > bootcmd_mmc=mmc init; ext2load mmc 0:1 0x00800000 > /uImage; ext2load mmc 0:1 0x01100000 /uInitrd > bootcmd_usb=usb start; ext2load usb 0:1 0x00800000 > /uImage; ext2load usb 0:1 0x01100000 /uInitrd > bootdelay=3 > bootfile=u-boot.bin > ceboardver=PPV4A1 > disL2Cache=no > disL2Prefetch=yes > disaMvPnp=no > enaCpuStream=no > enaDCPref=yes > enaICPref=yes > enaMonExt=no > enaWrAllo=no > ethact=egiga0 > ethaddr=00:25:31:05:86:37 > ethmtu=1500 > ethprime=egiga0 > hddPowerCtrl=no > ipaddr=10.0.0.117 > load_initd=ext2load usb 0:1 0x1100000 /boot/uInitr > d > load_initrd=ext2load usb 0:1 0x1100000 /boot/uInit > rd > load_nand=nboot 0x800000 0 0x200000 > load_nand2=nboot 0x800000 0 0x500000 > load_uimad=usb 0:1 0x800000 /boot/uImage\ > setenv mainlineLinux yes\ > setenv mtdids nand0=orion_nand\ > setenv mtdparts mtdparts=orion_nand:2M(u-boot),3M( > uImage),3M(uImage2),8M(failsafe),112M(root)\ > setenv partition nand0,2\ > setenv set_bootargs setenv bootargs console=$(cons > ole) root=LABEL=rootfs rootdelay=10 $(mtdparts) $( > custom_params)\ > setenv bootcmd_exec mw 0x800000 0 1 > load_uimage=ext2load usb 0:1 0x800000 /boot/uImage > loads_echo=0 > machid=F78 > mainlineLinux=yes > mtdids=nand0 orion_nand > mtdparts=mtdparts orion_nand:2M(u-boot),3M(uImage) > ,3M(uImage2),8M(failsafe),112M(root) > nandEcc=1bit > netbsd_en=no > netmask=255.255.255.0 > pcieTune=no > pexMode=RC > rootpath=t/ARM_FS/ > run_diag=yes > sata_dma_mode=yes > serverip=10.0.0.43 > setL2CacheWT=yes > set_bootargs=setenv bootargs console $(console) ro > ot LABEL rootfs rootdelay 10 $(mtdparts) $(custom_ > params) > stderr=serial > stdin=serial > stdout=serial > usb0Mode=host > vxworks_en=no > > Environment size: 1962/131068 bytes > >>
> > U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45) > Pogoplug V4 > > SoC: Kirkwood 88F6192_A1 > DRAM: 128 MiB > WARNING: Caches not enabled > NAND: 128 MiB > MMC: kwsdio: 0 > In: serial > Out: serial > Err: serial > Net: egiga0 [PRIME] > Hit any key to stop autoboot: 0 > Pogov4> > >>
Re: Pogoplug v4 usb image April 28, 2017 03:40PM |
Registered: 6 years ago Posts: 21 |
Re: Pogoplug v4 usb image April 28, 2017 06:01PM |
Registered: 6 years ago Posts: 21 |
wiki.xkyle.com/Install_Debian_on_a_Pogoplug.htmlbut something is not working
U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 Pogov4> reset resetting ... U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 Pogov4> tftp 0x1100000 uInitrd Using egiga0 device TFTP from server 10.0.0.43; our IP address is 10.0.0.117 Filename 'uInitrd'. Load address: 0x1100000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################### 3.2 MiB/s done Bytes transferred = 7179935 (6d8e9f hex) Pogov4> tftp 0x800000 uImage Using egiga0 device TFTP from server 10.0.0.43; our IP address is 10.0.0.117 Filename 'uImage'. Load address: 0x800000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 3.2 MiB/s done Bytes transferred = 4604912 (4643f0 hex) Pogov4> setenv bootargs console='ttyS0,115200 base-installer/initramfs-tools/dri ver-policy=most mirror/suite=stable apt-setup/local0/repository="http://people.d ebian.org/~tbm/orion/lenny/main" apt-setup/local0/key=http://people.debian.org/~ tbm/orion/68FD549F' Pogov4> bootm 0x00800000 0x01100000 ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.4.57-1-ARCH Created: 2017-03-27 5:43:34 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4604848 Bytes = 4.4 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.4.0-kirkwood-tld-1 Created: 2016-02-19 7:33:04 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7179871 Bytes = 6.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK Using machid 0xf78 from environment Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.57-1-ARCH (builduser@leming) (gcc version 6.3.1 20170306 (GCC) ) #1 PREEMPT Sun Mar 26 23:43:15 MDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397 f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: Pogoplug V4 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 32480 [ 0.000000] Kernel command line: console=ttyS0,115200 base-installer/initramf s-tools/driver-policy=most mirror/suite=stable apt-setup/local0/repository="http ://people.debian.org/~tbm/orion/lenny/main" apt-setup/local0/key=http://people.d ebian.org/~tbm/orion/68FD549F [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 112672K/131072K available (6606K kernel code, 547K rwdata , 1876K rodata, 300K init, 725K bss, 18400K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0850a04 (8483 kB) [ 0.000000] .init : 0xc0851000 - 0xc089c000 ( 300 kB) [ 0.000000] .data : 0xc089c000 - 0xc0924eec ( 548 kB) [ 0.000000] .bss : 0xc0924eec - 0xc09da4b8 ( 726 kB) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:114 [ 0.000020] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884 901885ns [ 10.640888] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xff ffffff, max_idle_ns: 11467562657 ns [ 10.641177] Console: colour dummy device 80x30 [ 10.641221] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216) [ 10.730997] pid_max: default: 32768 minimum: 301 [ 10.731144] Security Framework initialized [ 10.731258] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 10.731287] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 10.732490] Initializing cgroup subsys io [ 10.732542] Initializing cgroup subsys memory [ 10.732622] Initializing cgroup subsys devices [ 10.732664] Initializing cgroup subsys freezer [ 10.732699] Initializing cgroup subsys net_cls [ 10.732730] Initializing cgroup subsys perf_event [ 10.732764] Initializing cgroup subsys net_prio [ 10.732887] CPU: Testing write buffer coherency: ok [ 10.733575] Setting up static identity map for 0x81e0 - 0x8238 [ 10.736343] devtmpfs: initialized [ 10.740142] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns [ 10.740202] futex hash table entries: 256 (order: -1, 3072 bytes) [ 10.741024] pinctrl core: initialized pinctrl subsystem [ 10.742170] NET: Registered protocol family 16 [ 10.743040] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 10.771027] cpuidle: using governor ladder [ 10.801024] cpuidle: using governor menu [ 10.801381] Kirkwood: MV88F6281-A1, TCLK=166666667. [ 10.801419] Feroceon L2: Enabling L2 [ 10.801472] Feroceon L2: Cache support initialised. [ 10.804951] Kirkwood PCIe port 0: link down [ 10.804968] PCI: bus0 uses PCIe port 0 [ 10.805312] PCI host bridge to bus 0000:00 [ 10.805338] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] [ 10.805356] pci_bus 0000:00: root bus resource [io 0x1000-0xffff] [ 10.805372] pci_bus 0000:00: No busn resource found for root bus, will use [b us 00-ff] [ 10.805900] PCI: bus0: Fast back to back transfers disabled [ 10.843175] vgaarb: loaded [ 10.843628] SCSI subsystem initialized [ 10.844375] usbcore: registered new interface driver usbfs [ 10.844486] usbcore: registered new interface driver hub [ 10.844573] usbcore: registered new device driver usb [ 10.844819] pps_core: LinuxPPS API ver. 1 registered [ 10.844833] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome tti <giometti@linux.it> [ 10.844884] PTP clock support registered [ 10.846587] clocksource: Switched to clocksource orion_clocksource [ 10.903791] FS-Cache: Loaded [ 10.922774] NET: Registered protocol family 2 [ 10.923935] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 10.923973] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 10.924003] TCP: Hash tables configured (established 1024 bind 1024) [ 10.924114] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 10.924149] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 10.924427] NET: Registered protocol family 1 [ 10.924902] RPC: Registered named UNIX socket transport module. [ 10.924920] RPC: Registered udp transport module. [ 10.924930] RPC: Registered tcp transport module. [ 10.924940] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 10.925380] Trying to unpack rootfs image as initramfs... [ 11.795937] Freeing initrd memory: 7012K (c1100000 - c17d9000) [ 11.817599] VFS: Disk quotas dquot_6.6.0 [ 11.817998] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 11.821036] FS-Cache: Netfs 'nfs' registered for caching [ 11.822704] NFS: Registering the id_resolver key type [ 11.822788] Key type id_resolver registered [ 11.822800] Key type id_legacy registered [ 11.822924] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 11.824873] fuse init (API version 7.23) [ 11.828243] aufs 4.4-20170220 [ 11.835755] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 50) [ 11.835782] io scheduler noop registered [ 11.835800] io scheduler deadline registered [ 11.836192] io scheduler cfq registered [ 11.836698] io scheduler bfq registered (default) [ 11.836711] BFQ I/O-scheduler: v7r11 [ 11.837016] mv_xor mv_xor.0: Marvell shared XOR driver [ 11.878681] mv_xor mv_xor.0: Marvell XOR (Registers Mode): ( xor cpy ) [ 11.879031] mv_xor mv_xor.1: Marvell shared XOR driver [ 11.918567] mv_xor mv_xor.1: Marvell XOR (Registers Mode): ( xor cpy ) [ 11.926850] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 11.928414] console [ttyS0] disabled [ 11.948506] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 104 16666) is a 16550A [ 12.558426] console [ttyS0] enabled [ 12.585271] brd: module loaded [ 12.599856] loop: module loaded [ 12.603504] sata_mv sata_mv.0: cannot get optional clkdev [ 12.609082] sata_mv sata_mv.0: slots 32 ports 1 [ 12.616062] scsi host0: sata_mv [ 12.619791] ata1: SATA max UDMA/133 irq 21 [ 12.624913] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 12.631445] nand: Hynix H27U1G8F2BTR-BC [ 12.635270] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB siz e: 64 [ 12.642852] Scanning device for bad blocks [ 12.737697] Creating 5 MTD partitions on "orion_nand": [ 12.742838] 0x000000000000-0x000000200000 : "u-boot" [ 12.748620] 0x000000200000-0x000000500000 : "uImage" [ 12.754221] 0x000000500000-0x000000800000 : "uImage2" [ 12.760080] 0x000000800000-0x000001000000 : "failsafe" [ 12.765881] 0x000001000000-0x000008000000 : "root" [ 12.786261] libphy: orion_mdio_bus: probed [ 12.790612] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 12.976636] ata1: SATA link down (SStatus 0 SControl F300) [ 13.881017] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:05:86:37 [ 13.889959] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 13.896472] ehci-pci: EHCI PCI platform driver [ 13.901039] ehci-orion: EHCI orion driver [ 13.905143] orion-ehci orion-ehci.0: EHCI Host Controller [ 13.910590] orion-ehci orion-ehci.0: new USB bus registered, assigned bus num ber 1 [ 13.918359] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000 [ 13.936637] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00 [ 13.944024] hub 1-0:1.0: USB hub found [ 13.947894] hub 1-0:1.0: 1 port detected [ 13.952814] usbcore: registered new interface driver uas [ 13.958378] usbcore: registered new interface driver usb-storage [ 13.964443] usbcore: registered new interface driver ums-alauda [ 13.970475] usbcore: registered new interface driver ums-cypress [ 13.976535] usbcore: registered new interface driver ums-datafab [ 13.982623] usbcore: registered new interface driver ums_eneub6250 [ 13.988884] usbcore: registered new interface driver ums-freecom [ 13.994938] usbcore: registered new interface driver ums-isd200 [ 14.000938] usbcore: registered new interface driver ums-jumpshot [ 14.007114] usbcore: registered new interface driver ums-karma [ 14.012998] usbcore: registered new interface driver ums-onetouch [ 14.019198] usbcore: registered new interface driver ums-realtek [ 14.025257] usbcore: registered new interface driver ums-sddr09 [ 14.031256] usbcore: registered new interface driver ums-sddr55 [ 14.037250] usbcore: registered new interface driver ums-usbat [ 14.043699] mousedev: PS/2 mouse device common for all mice [ 14.266628] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 14.418898] usb-storage 1-1:1.0: USB Mass Storage device detected [ 14.425406] scsi host1: usb-storage 1-1:1.0 [ 15.056625] rtc-mv rtc-mv: internal RTC not ticking [ 15.061701] i2c /dev entries driver [ 15.066048] sdhci: Secure Digital Host Controller Interface driver [ 15.072240] sdhci: Copyright(c) Pierre Ossman [ 15.116915] sdhci-pltfm: SDHCI platform and OF driver helper [ 15.126429] ledtrig-cpu: registered to indicate activity on CPUs [ 15.132678] usbcore: registered new interface driver r8712u [ 15.138688] gre: GRE over IPv4 demultiplexor driver [ 15.143646] NET: Registered protocol family 17 [ 15.148335] Key type dns_resolver registered [ 15.155301] registered taskstats version 1 [ 15.182068] Key type encrypted registered [ 15.187335] console [netcon0] enabled [ 15.192036] netconsole: network logging started [ 15.199392] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 15.206562] hctosys: unable to open rtc device (rtc0) [ 15.215742] Freeing unused kernel memory: 300K (c0851000 - c089c000) Loading, please wait... [ 15.332640] systemd-udevd[121]: starting version 215 [ 15.349351] random: systemd-udevd: uninitialized urandom read (16 bytes read, 8 bits of entropy available) [ 15.437886] scsi 1:0:0:0: Direct-Access SanDisk Cruzer Blade 1.27 PQ : 0 ANSI: 6 [ 15.496109] sd 1:0:0:0: Attached scsi generic sg0 type 0 [ 15.502819] sd 1:0:0:0: [sda] 30529536 512-byte logical blocks: (15.6 GB/14.6 GiB) [ 15.549949] sd 1:0:0:0: [sda] Write Protect is off [ 15.572178] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doe sn't support DPO or FUA [ 15.630818] sda: sda1 [ 15.640438] sd 1:0:0:0: [sda] Attached SCSI removable disk modprobe: can't change directory to '4.4.57-1-ARCH': No such file or directory Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. modprobe: can't change directory to '4.4.57-1-ARCH': No such file or directory Begin: Checking file system ... fsck from util-linux 2.25.2 done. mount: can't find /root in /etc/fstab done. Target filesystem doesn't have requested /sbin/init. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... mount: mounting /dev on /root/dev failed : No such file or directory done. No init found. Try passing init= bootarg. modprobe: can't change directory to '4.4.57-1-ARCH': No such file or directory modprobe: can't change directory to '4.4.57-1-ARCH': No such file or directory modprobe: can't change directory to '4.4.57-1-ARCH': No such file or directory modprobe: can't change directory to '4.4.57-1-ARCH': No such file or directory modprobe: can't change directory to '4.4.57-1-ARCH': No such file or directory modprobe: can't change directory to '4.4.57-1-ARCH': No such file or directory modprobe: can't change directory to '4.4.57-1-ARCH': No such file or directory modprobe: can't change directory to '4.4.57-1-ARCH': No such file or directory BusyBox v1.22.1 (Debian 1:1.22.0-9+deb8u1) built-in shell (ash) Enter 'help' for a list of built-in commands. /bin/sh: can't access tty; job control turned off (initramfs) [ 165.265451] random: nonblocking pool is initialized (initramfs)
modprobe: can't change directory to '4.4.57-1-ARCH': No such file or directory Begin: Checking file system ... fsck from util-linux 2.25.2 done. mount: can't find /root in /etc/fstab done. Target filesystem doesn't have requested /sbin/init. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... mount: mounting /dev on /root/dev failed : No such file or directory done. No init found. Try passing init= bootarg.
Pogov4> printenv CASset=min MALLOC_len=1 apt-setup/local0/key=http://people.debian.org/~tbm/orion/68FD549F arcNumber=2097 baudrate=115200 boot=bootm 0x800000 boot_nand=run load_nand boot bootargs=console=ttyS0,115200 base-installer/initramfs-tools/driver-policy=most mirror/suite=stable apt-setup/local0/repository=http://people.debian.org/~tbm/orion/lenny/main apt-setup/local0/key=http://people.debian.org/~tbm/orion/68FD549F bootargs_console=console=ttyS0,115200 bootcmd=run set_bootargs; run bootcmd_exec; reset bootcmd_exec=mw 0x800000 0 1; load_uimage; run load_initrd; bootm 0x800000 0x1100000 bootcmd_mmc=mmc init; ext2load mmc 0:1 0x00800000 /uImage; ext2load mmc 0:1 0x01100000 /uInitrd bootcmd_usb=usb start; ext2load usb 0:1 0x00800000 /uImage; ext2load usb 0:1 0x01100000 /uInitrd bootdelay=3 bootfile=u-boot.bin ceboardver=PPV4A1 disL2Cache=no disL2Prefetch=yes disaMvPnp=no enaCpuStream=no enaDCPref=yes enaICPref=yes enaMonExt=no enaWrAllo=no ethact=egiga0 ethaddr=00:25:31:05:86:37 ethmtu=1500 ethprime=egiga0 fileaddr=800000 filesize=4643f0 hddPowerCtrl=no ipaddr=10.0.0.117 load_initd=ext2load usb 0:1 0x1100000 /boot/uInitrd load_initrd=ext2load usb 0:1 0x1100000 /boot/uInitrd load_nand=nboot 0x800000 0 0x200000 load_nand2=nboot 0x800000 0 0x500000 load_uimad=usb 0:1 0x800000 /boot/uImage\ setenv mainlineLinux yes\ setenv mtdids nand0=orion_nand\ setenv mtdparts mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)\ setenv partition nand0,2\ setenv set_bootargs setenv bootargs console=$(console) root=LABEL=rootfs rootdelay=10 $(mtdparts) $(custom_params)\ setenv bootcmd_exec mw 0x800000 0 1 load_uimage=ext2load usb 0:1 0x800000 /boot/uImage loads_echo=0 machid=F78 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) nandEcc=1bit netbsd_en=no netmask=255.255.255.0 partition=nand0,2 pcieTune=no pexMode=RC rootpath=t/ARM_FS/ run_diag=yes sata_dma_mode=yes serverip=10.0.0.43 setL2CacheWT=yes set_bootargs=setenv bootargs "console=$(console) root=LABEL=rootfs rootdelay=10 $(mtdparts) $(custom_params)" stderr=serial stdin=serial stdout=serial usb0Mode=host vxworks_en=no Environment size: 2306/131068 bytes Pogov4>
Re: Pogoplug v4 usb image April 28, 2017 06:56PM |
Admin Registered: 13 years ago Posts: 18,550 |
printev boot
Re: Pogoplug v4 usb image April 28, 2017 07:06PM |
Registered: 6 years ago Posts: 21 |
> printev>CASset=min MALLOC_len=1 apt-setup/local0/key=http://people.debian.org/~tbm/orion/68FD549F arcNumber=2097 baudrate=115200 boot=bootm 0x800000 boot_nand=run load_nand boot bootargs=console=ttyS0,115200 base-installer/initramfs-tools/driver-policy=most mirror/suite=stable apt-setup/local0/repository=http://people.debian.org/~tbm/orion/lenny/main apt-setup/local0/key=http://people.debian.org/~tbm/orion/68FD549F bootargs_console=console=ttyS0,115200 bootcmd=run set_bootargs; run bootcmd_exec; reset bootcmd_exec=mw 0x800000 0 1; load_uimage; run load_initrd; bootm 0x800000 0x1100000 bootcmd_mmc=mmc init; ext2load mmc 0:1 0x00800000 /uImage; ext2load mmc 0:1 0x01100000 /uInitrd bootcmd_usb=usb start; ext2load usb 0:1 0x00800000 /uImage; ext2load usb 0:1 0x01100000 /uInitrd bootdelay=3 bootfile=u-boot.bin ceboardver=PPV4A1 disL2Cache=no disL2Prefetch=yes disaMvPnp=no enaCpuStream=no enaDCPref=yes enaICPref=yes enaMonExt=no enaWrAllo=no ethact=egiga0 ethaddr=00:25:31:05:86:37 ethmtu=1500 ethprime=egiga0 fileaddr=800000 filesize=4643f0 hddPowerCtrl=no ipaddr=10.0.0.117 load_initd=ext2load usb 0:1 0x1100000 /boot/uInitrd load_initrd=ext2load usb 0:1 0x1100000 /boot/uInitrd load_nand=nboot 0x800000 0 0x200000 load_nand2=nboot 0x800000 0 0x500000 load_uimad=usb 0:1 0x800000 /boot/uImage\ setenv mainlineLinux yes\ setenv mtdids nand0=orion_nand\ setenv mtdparts mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)\ setenv partition nand0,2\ setenv set_bootargs setenv bootargs console=$(console) root=LABEL=rootfs rootdelay=10 $(mtdparts) $(custom_params)\ setenv bootcmd_exec mw 0x800000 0 1 load_uimage=ext2load usb 0:1 0x800000 /boot/uImage loads_echo=0 machid=F78 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) nandEcc=1bit netbsd_en=no netmask=255.255.255.0 partition=nand0,2 pcieTune=no pexMode=RC rootpath=t/ARM_FS/ run_diag=yes sata_dma_mode=yes serverip=10.0.0.43 setL2CacheWT=yes set_bootargs=setenv bootargs "console=$(console) root=LABEL=rootfs rootdelay=10 $(mtdparts) $(custom_params)" stderr=serial stdin=serial stdout=serial usb0Mode=host vxworks_en=no Environment size: 2306/131068 bytes
> boot
U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 [PRIME] Hit any key to stop autoboot: 3 2 1 0 Unknown command 'load_uimage' - try 'help' ** Bad device usb 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! resetting ... U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 [PRIME] Hit any key to stop autoboot: 3 0 Pogov4>
>
Re: Pogoplug v4 usb image April 29, 2017 03:50AM |
Admin Registered: 13 years ago Posts: 18,550 |
Re: Pogoplug v4 usb image May 01, 2017 10:27AM |
Registered: 6 years ago Posts: 21 |
10.780619] mmc0: host does not support reading read-only switch, assuming write-enable [ 10.792789] mmc0: new high speed SDHC card at address 0001 [ 10.799079] mmcblk0: mmc0:0001 AS 3.70 GiB [ 10.804735] mmcblk0: p1 [ 20.780907] VFS: Cannot open root device "LABEL=rootfs" or unknown-block(0,0): error -6 [ 20.788882] Please append a correct "root=" boot option; here are the available partitions: [ 20.797318] 0100 8192 ram0 (driver?) [ 20.802034] 0101 8192 ram1 (driver?) [ 20.806643] 0102 8192 ram2 (driver?) [ 20.811306] 0103 8192 ram3 (driver?) [ 20.815914] 0104 8192 ram4 (driver?) [ 20.820518] 0105 8192 ram5 (driver?) [ 20.825177] 0106 8192 ram6 (driver?) [ 20.829781] 0107 8192 ram7 (driver?) [ 20.834414] 0108 8192 ram8 (driver?) [ 20.839026] 0109 8192 ram9 (driver?) [ 20.843658] 010a 8192 ram10 (driver?) [ 20.848349] 010b 8192 ram11 (driver?) [ 20.853059] 010c 8192 ram12 (driver?) [ 20.857749] 010d 8192 ram13 (driver?) [ 20.862468] 010e 8192 ram14 (driver?) [ 20.867167] 010f 8192 ram15 (driver?) [ 20.871883] b300 3874816 mmcblk0 driver: mmcblk [ 20.877180] b301 3873792 mmcblk0p1 c53f5acc-01 [ 20.882502] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 20.890737] CPU: 0 PID: 1 Comm: swapper Not tainted 4.4.57-1-ARCH #1 [ 20.897064] Hardware name: Marvell SheevaPlug Reference Board [ 20.902822] [<c0010544>] (unwind_backtrace) from [<c000d9ec>] (show_stack+0x10/0x14) [ 20.910548] [<c000d9ec>] (show_stack) from [<c00cda94>] (panic+0x88/0x208) [ 20.917408] [<c00cda94>] (panic) from [<c08522c8>] (mount_block_root+0x1a0/0x260) [ 20.924868] [<c08522c8>] (mount_block_root) from [<c0852578>] (mount_root+0xf4/0x120) [ 20.932669] [<c0852578>] (mount_root) from [<c0852700>] (prepare_namespace+0x15c/0x1bc) [ 20.940646] [<c0852700>] (prepare_namespace) from [<c0851eb4>] (kernel_init_freeable+0x1fc/0x254) [ 20.949493] [<c0851eb4>] (kernel_init_freeable) from [<c06489b4>] (kernel_init+0x8/0xe8) [ 20.957555] [<c06489b4>] (kernel_init) from [<c000a4d0>] (ret_from_fork+0x14/0x24) [ 20.965097] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 95.040561] random: nonblocking pool is initialized
Re: Pogoplug v4 usb image May 02, 2017 12:32AM |
Admin Registered: 13 years ago Posts: 18,550 |
printenv boot