Assistance requested booting PogoOS April 27, 2017 11:11AM |
Registered: 6 years ago Posts: 6 |
root@Pogoplug:~# fw_printenv baudrate=115200 bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot; bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot; bootdelay=10 console=ttyS0,115200 device=0:1 ethact=egiga0 if_netconsole=ping $serverip led_error=orange blinking led_exit=green off led_init=green blinking mainlineLinux=yes mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi mmc_init=mmc rescan mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd mmc_root=/dev/mmcblk0p1 mtdids=nand0=orion_nand partition=nand0,2 rootdelay=10 rootfstype=ext3 sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi sata_init=ide reset sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd sata_root=/dev/sda1 set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_init=usb start usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd usb_root=/dev/sda1 ethaddr=00:25:31:05:b6:5a arcNumber=3960 machid=F78 usb_rootfstype=ext3 mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) bootcmd=run bootcmd_mmc; run bootcmd_usb; run bootcmd_pogo; run bootcmd_sata; reset bootcmd_pogo=if ubi part root 2048 && ubifsmount ubi:rootfs && ubifsload 0x800000 uboot.mtd0.dockstar.original.kwb ; then go 0x800200; fi preboot_nc=setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi preboot=run preboot_nc ipaddr=192.168.1.13 serverip=192.168.1.15
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) Pogoplug V4 gcc (Debian 4.9.2-10) 4.9.2 GNU ld (GNU Binutils for Debian) 2.25 Hit any key to stop autoboot: 0 ** Bad device mmc 0 ** ** Bad device mmc 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found ** Bad device usb 0 ** ** Bad device usb 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! ubi0: attaching mtd1 ubi0: scanning is finished ubi0: attached mtd1 (name "mtd=4", size 112 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 895, bad PEBs: 1, corrupted PEBs: 0 ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 6/4, WL threshold: 4096, image sequence number: 0 ubi0: available PEBs: 0, total reserved PEBs: 895, PEBs reserved for bad PEB handling: 8 Loading file 'uboot.mtd0.dockstar.original.kwb' to addr 0x00800000... Done ## Starting application at 0x00800200 ...
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) Pogoplug V4 gcc (Debian 4.9.2-10) 4.9.2 GNU ld (GNU Binutils for Debian) 2.25 Hit any key to stop autoboot: 0 MMC rescan: current device # 0 initialized OK 2875692 bytes read in 1202 ms (2.3 MiB/s) 6535284 bytes read in 1410 ms (4.4 MiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.18.5-kirkwood-tld-1 Created: 2015-11-11 5:03:31 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2875628 Bytes = 2.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-3.18.5-kirkwood-tld-1 Created: 2015-02-19 1:49:36 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6535220 Bytes = 6.2 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ...
Re: Assistance requested booting PogoOS April 27, 2017 05:25PM |
Admin Registered: 13 years ago Posts: 18,564 |
Re: Assistance requested booting PogoOS May 02, 2017 05:59AM |
Admin Registered: 13 years ago Posts: 18,564 |
## Starting application at 0x00800200 ...
mainlineLinux=yesWith stock OS, this variable should be set to no.
Re: Assistance requested booting PogoOS May 02, 2017 07:19AM |
Registered: 6 years ago Posts: 6 |
if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) Pogoplug V4 gcc (Debian 4.9.2-10) 4.9.2 GNU ld (GNU Binutils for Debian) 2.25 Hit any key to stop autoboot: 8 0 Pogov4> if fsload uboot-original-mtd0.kwb; then go 0x800200; fi if fsload uboot-original-mtd0.kwb; then go 0x800200; fi ### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000 Scanning JFFS2 FS: read_nand_cached: error reading nand off 0x5fec00 size 8192 bytes read_nand_cached: error reading nand off 0x5fea00 size 8192 bytes read_nand_cached: error reading nand off 0x68c000 size 8192 bytes read_nand_cached: error reading nand off 0x68be00 size 8192 bytes done. find_inode failed for name=uboot-original-mtd0.kwb load: Failed to find inode ### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb! Pogov4>
Re: Assistance requested booting PogoOS May 03, 2017 01:17AM |
Admin Registered: 13 years ago Posts: 18,564 |
Quote
Serial Console & JTAG console
Repair Pogo E02 with Raspberry PI (JTAG) and OpenOCD
Serial Port connector - what are people using to make it work
Serial Console hookup - GoFlex Net (external link)
Serial Console hookup - Pogoplug E02 and Pogoplug Pro V3 (external link)
OSX Serial/Net Console
Use Phone Jack - Phone Jack Serial Console Pics
Adding serial connector to Pogoplug Mobile (external link)
> if fsload uboot-original-mtd0.kwb; then go 0x80020 > 0; fi >
Re: Assistance requested booting PogoOS May 16, 2017 05:35AM |
Registered: 6 years ago Posts: 6 |
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Using egiga0 device host 192.168.1.15 is alive Using egiga0 device host 192.168.1.15 is alive Using egiga0 device host 192.168.1.15 is alive Using egiga0 device host 192.168.1.15 is alive Using egiga0 device host 192.168.1.15 is alive U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: MV88F6192 Rev 3 (DDR2) CPU running @ 800Mhz L2 running @ 400Mhz SysClock = 200Mhz , TClock = 166Mhz DRAM CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: PPV4A1 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 Loading from NAND 128MB 3,3V 8-bit, offset 0x200000 Image Name: Linux-2.6.31.8 Created: 2011-08-23 20:00:55 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2080956 Bytes = 2 MB Load Address: 00008000 Entry Point: 00008000 ## Booting image at 00800000 ... Image Name: Linux-2.6.31.8 Created: 2011-08-23 20:00:55 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2080956 Bytes = 2 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... Bad Data CRC CE>>
Re: Assistance requested booting PogoOS May 16, 2017 11:11AM |
Admin Registered: 13 years ago Posts: 18,564 |
Using egiga0 device host 192.168.1.15 is alive Using egiga0 device
printenv
Re: Assistance requested booting PogoOS May 16, 2017 11:40AM |
Registered: 6 years ago Posts: 6 |
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Using egiga0 device host 192.168.1.15 is alive Using egiga0 device host 192.168.1.15 is alive Using egiga0 device host 192.168.1.15 is alive Using egiga0 device host 192.168.1.15 is alive Using egiga0 device host 192.168.1.15 is alive U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: MV88F6192 Rev 3 (DDR2) CPU running @ 800Mhz L2 running @ 400Mhz SysClock = 200Mhz , TClock = 166Mhz DRAM CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: PPV4A1 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 CE>> printenv baudrate=115200 loads_echo=0 rootpath=/mnt/ARM_FS/ netmask=255.255.0.0 run_diag=yes CASset=min MALLOC_len=1 ethprime=egiga0 load_nand=nboot 0x800000 0 0x200000 load_nand2=nboot 0x800000 0 0x500000 boot=bootm 0x800000 boot_nand=run load_nand boot || run load_nand2 boot ethmtu=1500 usb0Mode=host nandEcc=1bit hddPowerCtrl=no pcieTune=no ethact=egiga0 ethaddr=00:25:31:05:b6:5a cesvcid=VE8MFDXJSXPAE9S6SJA8B8R5CA ceboardver=PPV4A1 ipaddr=192.168.58.233 serverip=192.168.58.188 bootargs=console=ttyS0,115200 root=ubi0:rootfs ubi.mtd=4,2048 rootfstype=ubifs bootcmd=run boot_nand stdin=serial stdout=serial stderr=serial console=console=ttyS0,115200 mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootargs_root=root=/dev/mtdblock2 ro bootdelay=3 disaMvPnp=no Environment size: 900/131068 bytes CE>>
Re: Assistance requested booting PogoOS May 16, 2017 11:44AM |
Admin Registered: 13 years ago Posts: 18,564 |
Re: Assistance requested booting PogoOS May 16, 2017 11:47AM |
Admin Registered: 13 years ago Posts: 18,564 |
host 192.168.1.15
Re: Assistance requested booting PogoOS May 16, 2017 12:20PM |
Registered: 6 years ago Posts: 6 |
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.1.15 is not alive Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.1.15 is not alive Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.1.15 is not alive Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.1.15 is not alive Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.1.15 is not alive Hit any key to stop autoboot: 0 Pogov4> printenv arcNumber=3960 baudrate=115200 bootcmd=run bootcmd_mmc; run bootcmd_usb; run bootcmd_pogo; run bootcmd_sata; reset bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot bootcmd_pogo=if ubi part root 2048 && ubifsmount ubi:rootfs && ubifsload 0x800000 uboot.mtd0.dockstar.original.kwb ; then go 0x800200; fi bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot; bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot; bootdelay=10 console=ttyS0,115200 device=0:1 ethact=egiga0 ethaddr=00:25:31:05:b6:5a if_netconsole=ping $serverip ipaddr=192.168.1.13 led_error=orange blinking led_exit=green off led_init=green blinking machid=F78 mainlineLinux=yes mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi mmc_init=mmc rescan mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd mmc_root=/dev/mmcblk0p1 mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) nc_ready=0 partition=nand0,2 preboot=run preboot_nc preboot_nc=setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi rootdelay=10 rootfstype=ext3 sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi sata_init=ide reset sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd sata_root=/dev/sda1 serverip=192.168.1.15 set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_init=usb start usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd usb_root=/dev/sda1 usb_rootfstype=ext3 Environment size: 2586/131068 bytes Pogov4>
U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: MV88F6192 Rev 3 (DDR2) CPU running @ 800Mhz L2 running @ 400Mhz SysClock = 200Mhz , TClock = 166Mhz DRAM CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: PPV4A1 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 Loading from NAND 128MB 3,3V 8-bit, offset 0x200000 Image Name: Linux-2.6.31.8 Created: 2011-08-23 20:00:55 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2080956 Bytes = 2 MB Load Address: 00008000 Entry Point: 00008000 ## Booting image at 00800000 ... Image Name: Linux-2.6.31.8 Created: 2011-08-23 20:00:55 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2080956 Bytes = 2 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux..................................................................................................................................... done, booting the kernel. [ 0.000000] Linux version 2.6.31.8 (afenn@kt) (gcc version 4.3.2 (sdk3.3-ct-ng-1.4.1) ) #4 Tue Aug 23 13:00:50 PDT 2011 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053177 [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: Feroceon-KW [ 0.000000] Using UBoot passing parameters structure [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 root=ubi0:rootfs ubi.mtd=4,2048 rootfstype=ubifs [ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 128MB = 128MB total [ 0.000000] Memory: 118356KB available (3852K code, 261K data, 124K init, 0K highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:128 [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Calibrating delay loop... 799.53 BogoMIPS (lpj=3997696) [ 0.230000] Mount-cache hash table entries: 512 [ 0.230000] CPU: Testing write buffer coherency: ok [ 0.230000] NET: Registered protocol family 16 [ 0.230000] Feroceon L2: Enabling L2 [ 0.230000] Feroceon L2: Cache support initialised. [ 0.230000] [ 0.230000] CPU Interface [ 0.230000] ------------- [ 0.230000] SDRAM_CS0 ....base 00000000, size 128MB [ 0.230000] SDRAM_CS1 ....disable [ 0.230000] SDRAM_CS2 ....disable [ 0.230000] SDRAM_CS3 ....disable [ 0.230000] PEX0_MEM ....base e0000000, size 128MB [ 0.230000] PEX0_IO ....base f2000000, size 1MB [ 0.230000] PEX1_MEM ....no such [ 0.230000] PEX1_IO ....no such [ 0.230000] INTER_REGS ....base f1000000, size 1MB [ 0.230000] NFLASH_CS ....base fa000000, size 2MB [ 0.230000] SPI_CS ....base f4000000, size 16MB [ 0.230000] BOOT_ROM_CS ....no such [ 0.230000] DEV_BOOTCS ....no such [ 0.230000] CRYPT_ENG ....base f0000000, size 2MB [ 0.230000] [ 0.230000] Marvell Development Board (LSP Version KW_LSP_5.1.3_patch18)-- SHEEVA PLUG Soc: 88F6192 A1 LE [ 0.230000] [ 0.230000] Detected Tclk 166666667 and SysClk 200000000 [ 0.230000] Marvell USB EHCI Host controller #0: c403e740 [ 0.730000] PEX0 interface detected no Link. [ 0.740000] PCI: bus0: Fast back to back transfers enabled [ 0.740000] mvPexLocalBusNumSet: ERR. Invalid PEX interface 1 [ 0.750000] bio: create slab <bio-0> at 0 [ 0.750000] SCSI subsystem initialized [ 0.750000] usbcore: registered new interface driver usbfs [ 0.750000] usbcore: registered new interface driver hub [ 0.750000] usbcore: registered new device driver usb [ 0.750000] NET: Registered protocol family 2 [ 0.750000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.750000] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.750000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.750000] TCP: Hash tables configured (established 4096 bind 4096) [ 0.750000] TCP reno registered [ 0.750000] NET: Registered protocol family 1 [ 0.750000] cpufreq: Init kirkwood cpufreq driver [ 0.760000] XOR registered 4 channels [ 0.760000] XOR 2nd invalidate WA enabled [ 0.760000] cesadev_init(c000d7fc) [ 0.760000] mvCesaInit: sessions=640, queue=64, pSram=f0000000 [ 0.770000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.770000] msgmni has been set to 231 [ 0.770000] alg: No test for cipher_null (cipher_null-generic) [ 0.770000] alg: No test for ecb(cipher_null) (ecb-cipher_null) [ 0.770000] alg: No test for digest_null (digest_null-generic) [ 0.770000] alg: No test for compress_null (compress_null-generic) [ 0.780000] alg: No test for stdrng (krng) [ 0.780000] alg: No test for hmac(digest_null) (hmac(digest_null-generic)) [ 0.790000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.790000] io scheduler noop registered [ 0.790000] io scheduler anticipatory registered (default) [ 0.790000] Initializing ths8200_init [ 0.790000] Initializing dove_adi9889_init [ 0.810000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.810000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A [ 0.810000] console [ttyS0] enabled [ 0.820000] [ 0.820000] Warning Sata is Powered Off [ 0.820000] Loading Marvell Ethernet Driver: [ 0.830000] o Cached descriptors in DRAM [ 0.830000] o DRAM SW cache-coherency [ 0.840000] o 1 Giga ports supported [ 0.840000] o Single RX Queue support - ETH_DEF_RXQ=0 [ 0.840000] o Single TX Queue support - ETH_DEF_TXQ=0 [ 0.850000] o TCP segmentation offload (TSO) supported [ 0.860000] o Large Receive offload (LRO) supported [ 0.860000] o Receive checksum offload supported [ 0.860000] o Transmit checksum offload supported [ 0.870000] o Network Fast Processing (Routing) supported - (Disabled) [ 0.880000] o Driver ERROR statistics enabled [ 0.880000] o Proc tool API enabled [ 0.880000] o SKB Reuse supported - (Disabled) [ 0.890000] o SKB Recycle supported - (Disabled) [ 0.890000] o Rx descripors: q0=128 [ 0.900000] o Tx descripors: q0=532 [ 0.900000] o Loading network interface(s): [ 0.910000] o register under mv88fx_eth platform [ 0.910000] o eth0, ifindex = 2, GbE port = 0 [ 0.920000] [ 0.920000] mvFpRuleDb (c432a000): 1024 entries, 4096 bytes [ 0.920000] Counter=0, opIdx=6, overhead=16 [ 0.930000] Counter=1, opIdx=2, overhead=0 [ 0.930000] Counter=2, opIdx=1, overhead=18 [ 0.940000] Counter=3, opIdx=2, overhead=0 [ 0.940000] tun: Universal TUN/TAP device driver, 1.6 [ 0.950000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 0.950000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit) [ 0.960000] Scanning device for bad blocks [ 1.010000] Bad eraseblock 1004 at 0x000007d80000 [ 1.020000] Using static partition definition [ 1.020000] Creating 5 MTD partitions on "nand_mtd": [ 1.030000] 0x000000000000-0x000000200000 : "u-boot" [ 1.030000] 0x000000200000-0x000000500000 : "uImage" [ 1.040000] 0x000000500000-0x000000800000 : "uImage2" [ 1.040000] 0x000000800000-0x000001000000 : "failsafe" [ 1.050000] 0x000001000000-0x000008000000 : "root" [ 1.060000] UBI: attaching mtd4 to ubi0 [ 1.060000] UBI: physical eraseblock size: 131072 bytes (128 KiB) [ 1.070000] UBI: logical eraseblock size: 126976 bytes [ 1.070000] UBI: smallest flash I/O unit: 2048 [ 1.080000] UBI: sub-page size: 512 [ 1.080000] UBI: VID header offset: 2048 (aligned 2048) [ 1.090000] UBI: data offset: 4096 [ 1.320000] UBI: attached mtd4 to ubi0 [ 1.320000] UBI: MTD device name: "root" [ 1.330000] UBI: MTD device size: 112 MiB [ 1.330000] UBI: number of good PEBs: 895 [ 1.340000] UBI: number of bad PEBs: 1 [ 1.340000] UBI: max. allowed volumes: 128 [ 1.350000] UBI: wear-leveling threshold: 4096 [ 1.350000] UBI: number of internal volumes: 1 [ 1.350000] UBI: number of user volumes: 1 [ 1.360000] UBI: available PEBs: 0 [ 1.360000] UBI: total number of reserved PEBs: 895 [ 1.370000] UBI: number of PEBs reserved for bad PEB handling: 8 [ 1.370000] UBI: max/mean erase counter: 6/4 [ 1.380000] UBI: image sequence number: 0 [ 1.380000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.390000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI [ 1.390000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 [ 1.400000] UBI: background thread "ubi_bgt0d" started, PID 445 [ 1.430000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 [ 1.450000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00 [ 1.450000] usb usb1: configuration #1 chosen from 1 choice [ 1.460000] hub 1-0:1.0: USB hub found [ 1.460000] hub 1-0:1.0: 1 port detected [ 1.470000] Initializing USB Mass Storage driver... [ 1.470000] usbcore: registered new interface driver usb-storage [ 1.480000] USB Mass Storage support registered. [ 1.480000] usbcore: registered new interface driver ums-datafab [ 1.490000] usbcore: registered new interface driver ums-freecom [ 1.490000] usbcore: registered new interface driver ums-jumpshot [ 1.500000] usbcore: registered new interface driver ums-sddr09 [ 1.510000] usbcore: registered new interface driver ums-sddr55 [ 1.510000] usbcore: registered new interface driver ums-usbat [ 1.520000] mice: PS/2 mouse device common for all mice [ 1.520000] i2c /dev entries driver [ 1.540000] sdhci: Secure Digital Host Controller Interface driver [ 1.540000] sdhci: Copyright(c) Pierre Ossman [ 1.550000] mmc0: mvsdio driver initialized, lacking card detect (fall back to polling) [ 1.560000] usbcore: registered new interface driver usbhid [ 1.560000] usbhid: v2.6:USB HID core driver [ 1.570000] TCP cubic registered [ 1.570000] NET: Registered protocol family 17 [ 1.580000] RPC: Registered udp transport module. [ 1.580000] RPC: Registered tcp transport module. [ 1.590000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 1.660000] UBIFS: recovery needed [ 1.760000] UBIFS: recovery completed [ 1.760000] UBIFS: mounted UBI device 0, volume 0, name "rootfs" [ 1.770000] UBIFS: file system size: 110723072 bytes (108128 KiB, 105 MiB, 872 LEBs) [ 1.780000] UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs) [ 1.790000] UBIFS: media format: w4/r0 (latest is w4/r0) [ 1.790000] UBIFS: default compressor: lzo [ 1.800000] UBIFS: reserved for root: 0 bytes (0 KiB) [ 1.800000] VFS: Mounted root (ubifs filesystem) on device 0:11. [ 1.810000] Freeing init memory: 124K [ 4.190000] eth0: link down [ 4.200000] eth0: started udhcpc (v1.16.1) started HWADDR 00 0x25 0x31 0x05 0xb6 0x5a PIP0 182 PIP1 90 cat: can't open '/etc/resolv.conf': No such file or directory route: SIOCDELRT: No such process grep: /etc/resolv.conf: No such file or directory Sending discover... [ 6.080000] eth0: link up, full duplex, speed 1 Gbps Sending discover... Sending select for 192.168.1.13... Lease of 192.168.1.13 obtained, lease time 43200 HWADDR 00 0x25 0x31 0x05 0xb6 0x5a PIP0 182 PIP1 90 route: SIOCDELRT: No such process Loading gpio_keys.ko... Loading ejectbutton.ko... [ 8.260000] IRQ 93 uses trigger mode 0; requested 3 [ 8.270000] input: gpio-keys as /devices/platform/gpio-keys.0/input/input0 [ 8.280000] xce_ebtn: Pogoplug series V4 eject button initialized. [ 8.430000] ufsd: module license 'Commercial product' taints kernel. [ 8.430000] Disabling lock debugging due to kernel taint [ 8.470000] ufsd: driver (8.6 (U86_S[2012-02-28-18:39:23]), LBD=ON, delalloc, ioctl) loaded at bf00c000 [ 8.470000] NTFS support included [ 8.470000] Hfs+/HfsX support included [ 8.470000] For 'CloudEngines_PogoPlug_2011-08-03' Loading rt3070sta.ko: [ 8.810000] rtusb init rt2870 ---> [ 8.820000] usbcore: registered new interface driver rt2870 Success Loading xce.ko: [ 8.840000] Cloud Engines XCE Init [Version: 3.9.0.4] [ 8.850000] XCE: CPU MEMORY MAP: [ 8.850000] XCE: -- 0x00001000 - 0xbeffffff (3055 MB) User Space Mappings [ 8.860000] XCE: -- 0xbf000000 - 0xbfffffff ( 16 MB) Kernel module space [ 8.870000] XCE: -- 0xc0000000 - 0xc7ffffff ( 128 MB) Kernel direct-mapped ram [ 8.870000] XCE: -- 0xc8800000 - 0xe7ffffff ( 504 MB) Kernel vmalloc space [ 8.880000] XCE: -- 0xe8000000 - 0xfeffffff ( 367 MB) Kernel platform space [ 8.890000] XCE: CPU FEATURES: [ 8.890000] XCE: -- I Cache: enabled [ 8.900000] XCE: -- D Cache: enabled [ 8.900000] XCE: -- Branch Predict: enabled [ 8.900000] XCE: -- MMU: enabled [ 8.910000] XCE: -- Alignment Abort: enabled [ 8.920000] XCE: BLPARAMS: -- Loading properties [c49efefc]. [ 8.920000] XCE: BLPARAMS: -- MTD @ [c4324000]. [ 8.930000] XCE: BLPARAMS: Locating parameter block... [ 8.930000] XCE: BLPARAMS: reading 2048 bytes @ a0000 [ 8.940000] XCE: Loaded Property Size: 2048 [ 8.940000] XCE: - 'cesvcid' -> 'VE8MFDXJSXPAE9S6SJA8B8R5CA' [ 8.950000] XCE: - 'ceboardver' -> 'PPV4A1' [ 8.960000] XCE: -- ICache Prefetch: enabled [ 8.960000] XCE: -- DCache Prefetch: enabled [ 8.960000] XCE: -- L2 Cache: enabled [ 8.970000] XCE: -- L2 Prefetch: disabled [ 8.970000] XCE: -- L2 Writethrough: disabled [ 8.980000] XCE: -- Write Allocate: disabled [ 8.980000] XCE: -- Streaming: disabled [ 8.990000] XCE: Current GPIO State: [ 8.990000] XCE: GPIO L OUT: 0x21400000 [ 8.990000] XCE: GPIO L OE: 0x30000000 [ 9.000000] XCE: GPIO L BLINK: 0x00000000 [ 9.000000] XCE: GPIO L POL: 0x00000000 [ 9.010000] XCE: GPIO L IN: 0x11400000 [ 9.010000] XCE: GPIO H OUT: 0xfffc7fff [ 9.020000] XCE: GPIO H OE: 0x00000000 [ 9.020000] XCE: GPIO H BLINK: 0x00004000 [ 9.020000] XCE: GPIO H POL: 0x00000000 [ 9.030000] XCE: GPIO H IN: 0x0000000f Success Starting hbplug: Success / # [ 9.210000] XCE: BLPARAMS: -- Loading properties [c49efecc]. [ 9.220000] XCE: BLPARAMS: -- MTD @ [c4324000]. [ 9.220000] XCE: BLPARAMS: Locating parameter block... [ 9.230000] XCE: BLPARAMS: reading 2048 bytes @ a0000 [ 9.230000] XCE: BLPARAMS: reading 2048 bytes @ a0800 [ 9.240000] XCE: BLPARAMS: reading 2048 bytes @ a1000 [ 9.250000] XCE: BLPARAMS: reading 2048 bytes @ a1800 / # [ 14.780000] XCE: XCE: LED -> CONNECTED / #
Re: Assistance requested booting PogoOS May 16, 2017 12:53PM |
Admin Registered: 13 years ago Posts: 18,564 |
setenv archNumber setenv machid boot
Re: Assistance requested booting PogoOS May 16, 2017 01:51PM |
Registered: 6 years ago Posts: 6 |
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.1.15 is not alive Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.1.15 is not alive Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.1.15 is not alive Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.1.15 is not alive Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.1.15 is not alive Hit any key to stop autoboot: 0 Pogov4> setenv archNumber Pogov4> setenv machid Pogov4> boot ** Bad device mmc 0 ** ** Bad device mmc 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found ** Bad device usb 0 ** ** Bad device usb 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! ubi0: attaching mtd1 ubi0: scanning is finished ubi0: attached mtd1 (name "mtd=4", size 112 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 895, bad PEBs: 1, corrupted PEBs: 0 ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 6/4, WL threshold: 4096, image sequence number: 0 ubi0: available PEBs: 0, total reserved PEBs: 895, PEBs reserved for bad PEB handling: 8 Loading file 'uboot.mtd0.dockstar.original.kwb' to addr 0x00800000... Done ## Starting application at 0x00800200 ... U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: MV88F6192 Rev 3 (DDR2) CPU running @ 800Mhz L2 running @ 400Mhz SysClock = 200Mhz , TClock = 166Mhz DRAM CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: PPV4A1 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 Loading from NAND 128MB 3,3V 8-bit, offset 0x200000 Image Name: Linux-2.6.31.8 Created: 2011-08-23 20:00:55 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2080956 Bytes = 2 MB Load Address: 00008000 Entry Point: 00008000 ## Booting image at 00800000 ... Image Name: Linux-2.6.31.8 Created: 2011-08-23 20:00:55 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2080956 Bytes = 2 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... Bad Data CRC CE>>
Re: Assistance requested booting PogoOS May 17, 2017 06:28AM |
Admin Registered: 13 years ago Posts: 18,564 |
setenv archNumber 3960 boot