Welcome! Log In Create A New Profile

Advanced

Booting Pogo V3 Debian rootfs from OpenWrt u-boot

Posted by ming 
Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 02, 2017 08:51AM
bodhi Wrote:
-------------------------------------------------------
> ming,
>
> hahibie has a good point, if the uboot envs are c
> urrently set up to boot Openwrt, you need to modif
> y them to boot USB. Please post the current uboot
> envs if you have installed new uboot.
root@PogoPlug:/# fdisk -l 
You must set cylinders.
You can do this from the extra functions menu.

Disk /dev/mtdblock0: 0 MB, 262144 bytes
171 heads, 42 sectors/track, 0 cylinders, total 512 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0xaaaaaaaa

This doesn't look like a partition table
Probably you selected the wrong device.

          Device Boot      Start         End      Blocks   Id  System
/dev/mtdblock0p1   ?  2863311530  1431655763  1431655765   aa  Unknown
/dev/mtdblock0p2   ?  2863311530  1431655763  1431655765   aa  Unknown
/dev/mtdblock0p3   ?  2863311530       21843   715838805   aa  Unknown
/dev/mtdblock0p4   ?  2863311530  1426085203  1428870485   aa  Unknown
You must set cylinders.
You can do this from the extra functions menu.

Disk /dev/mtdblock1: 1 MB, 1441792 bytes
255 heads, 63 sectors/track, 0 cylinders, total 2816 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0xaaaaaaaa

This doesn't look like a partition table
Probably you selected the wrong device.

          Device Boot      Start         End      Blocks   Id  System
/dev/mtdblock1p1   ?  1437226410     5570643  1431655765   aa  Unknown
/dev/mtdblock1p2   ?  2863289685     5570558   718624085   aa  Unknown
/dev/mtdblock1p3   ?  1431677610       21843  1431655765   aa  Unknown
/dev/mtdblock1p4   ?  2863289685     5570558   718624085   aa  Unknown

Partition table entries are not in disk order

Disk /dev/mtdblock2: 0 MB, 262144 bytes
255 heads, 63 sectors/track, 0 cylinders, total 512 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes


Disk /dev/mtdblock3: 33 MB, 33554432 bytes
171 heads, 42 sectors/track, 9 cylinders, total 65536 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0xaaaaaaaa

This doesn't look like a partition table
Probably you selected the wrong device.

          Device Boot      Start         End      Blocks   Id  System
/dev/mtdblock3p1   ?  2863311530  1431655763  1431655765   aa  Unknown
/dev/mtdblock3p2   ?  2863311530  1431655763  1431655765   aa  Unknown
/dev/mtdblock3p3   ?  2863311530       21843   715838805   aa  Unknown
/dev/mtdblock3p4   ?  2863311530  1426085203  1428870485   aa  Unknown

Disk /dev/mtdblock4: 0 MB, 131072 bytes
255 heads, 63 sectors/track, 0 cylinders, total 256 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes


Disk /dev/mtdblock5: 10 MB, 10485760 bytes
255 heads, 63 sectors/track, 1 cylinders, total 20480 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes


Disk /dev/mtdblock6: 119 MB, 119537664 bytes
255 heads, 63 sectors/track, 14 cylinders, total 233472 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes


Disk /dev/mtdblock7: 132 MB, 132120576 bytes
255 heads, 63 sectors/track, 16 cylinders, total 258048 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes


Disk /dev/mtdblock8: 134 MB, 134217728 bytes
171 heads, 42 sectors/track, 36 cylinders, total 262144 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0xaaaaaaaa

This doesn't look like a partition table
Probably you selected the wrong device.

          Device Boot      Start         End      Blocks   Id  System
/dev/mtdblock8p1   ?  2863311530  1431655763  1431655765   aa  Unknown
/dev/mtdblock8p2   ?  2863311530  1431655763  1431655765   aa  Unknown
/dev/mtdblock8p3   ?  2863311530       21843   715838805   aa  Unknown
/dev/mtdblock8p4   ?  2863311530  1426085203  1428870485   aa  Unknown

Disk /dev/sda: 1000.2 GB, 1000204886016 bytes
255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes


Disk /dev/sdb: 16.2 GB, 16239329280 bytes
64 heads, 32 sectors/track, 15487 cylinders, total 31717440 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes

root@PogoPlug:/# tune2fs -L rootfs /dev/sdb
tune2fs 1.42.4 (12-June-2012)
root@PogoPlug:/#

how can i set up to boot USB rootfs



Edited 1 time(s). Last edit at 05/02/2017 11:09PM by bodhi.
Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 04, 2017 07:17PM
root@PogoPlug:~# cat /etc/fw_env.config
# MTD device name       Device offset   Env. size       Flash sector size       Number of sectors
/dev/mtd2       0x0        0x2000      0x40000
root@PogoPlug:~# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00040000 00020000 "stage1"
mtd1: 00160000 00020000 "u-boot"
mtd2: 00040000 00020000 "u-boot-env"
mtd3: 02000000 00020000 "boot"
mtd4: 00020000 00020000 "factory"
mtd5: 00a00000 00020000 "kernel"
mtd6: 07200000 00020000 "rootfs"
mtd7: 07e00000 00020000 "firmware"
mtd8: 08000000 00020000 "fullflash"
root@PogoPlug:~#
Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 17, 2017 08:43PM
Should i follow these steps?
- set up to boot USB rootfs first,
- adjust mtdparts to be same as above
- boot this USB rootfs successfully
- verify that the mtds definition are correct.
- flash new u-boot and its default envs images.
Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 17, 2017 08:51PM
How to set up to boot USB rootfs first.Is there any blog that you can learn from?
Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 18, 2017 12:32AM
ming Wrote:
-------------------------------------------------------
> How to set up to boot USB rootfs first.Is there an
> y blog that you can learn from?


Right here in this forum:
http://forum.doozan.com/read.php?2,16044

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 18, 2017 07:19AM
root@PogoPlug:/media/sdb1/boot# mkimage  -A arm -O linux -C none -T kernel -a 0x
60008000 -e 0x60008000 -n 'Linux-3.3.17.0-oxnas-tld-1' -d zImage-3.17.0-oxnas-tl
d-1.fdt uImage sync
/bin/ash: mkimage: not found
Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 18, 2017 10:17AM
ming Wrote:
-------------------------------------------------------
>
> root@PogoPlug:/media/sdb1/boot# mkimage  -A arm -O
> linux -C none -T kernel -a 0x
> 60008000 -e 0x60008000 -n 'Linux-3.3.17.0-oxnas-tl
> d-1' -d zImage-3.17.0-oxnas-tl
> d-1.fdt uImage sync
> /bin/ash: mkimage: not found
>

Look for mkimage binary:
find /media/sdb1/ mkimage

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 18, 2017 06:29PM
find: mkimage: No such file or directory
Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 18, 2017 11:36PM
Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 19, 2017 02:09AM
My mtd0 is too small,How can i adjust it
root@PogoPlug:~# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00040000 00020000 "stage1"
mtd1: 00160000 00020000 "u-boot"
mtd2: 00040000 00020000 "u-boot-env"
mtd3: 02000000 00020000 "boot"
mtd4: 00020000 00020000 "factory"
mtd5: 00a00000 00020000 "kernel"
mtd6: 07200000 00020000 "rootfs"
mtd7: 07e00000 00020000 "firmware"
mtd8: 08000000 00020000 "fullflash"
Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 19, 2017 07:12AM
ming Wrote:
-------------------------------------------------------
> My mtd0 is too small,How can i adjust it
>
> root@PogoPlug:~# cat /proc/mtd
> dev:    size   erasesize  name
> mtd0: 00040000 00020000 "stage1"
> mtd1: 00160000 00020000 "u-boot"
> mtd2: 00040000 00020000 "u-boot-env"
> mtd3: 02000000 00020000 "boot"
> mtd4: 00020000 00020000 "factory"
> mtd5: 00a00000 00020000 "kernel"
> mtd6: 07200000 00020000 "rootfs"
> mtd7: 07e00000 00020000 "firmware"
> mtd8: 08000000 00020000 "fullflash"
>

Connect serial console, and we can adjust the mtdparts definition in u-boot console.

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 19, 2017 10:18AM
I have connected the box with the serial console, and how can I adjust it or can you give me a keyword so that I can search for related topics?
Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 19, 2017 11:29AM
ming Wrote:
-------------------------------------------------------
> I have connected the box with the serial console,
> and how can I adjust it or can you give me a keywo
> rd so that I can search for related topics?

Interrupt serial console and

setenv mtdparts  'mtdparts=41000000.nand:14m(boot),-(data)'

and then let it boot:
boot

Affer booting into Debian,

cat /proc/mtd
Expected output

dev:    size   erasesize  name
mtd0: 00e00000 00020000 "boot"
mtd1: 07200000 00020000 "data"


If you see the expected output, then you can flash new u-boot.

Important: don't save the envs in serial console, until after you can boot into Dedian and see the mtd layout as shown above.

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 19, 2017 12:34PM
[root@PogoPlug-Pro]#setenv mtdparts  'mtdparts=41000000.nand:14m(boot),-(data)'
[root@PogoPlug-Pro]#boot
Unknown command 'boot' - try 'help'
[root@PogoPlug-Pro]#help
?       - alias for 'help'
base    - print or set address offset
bdinfo  - print Board Info structure
bootm   - boot application image from memory
bootp	- boot image via network using BootP/TFTP protocol
cmp     - memory compare
cp      - memory copy
crc32   - checksum calculation
diskboot- boot from IDE device
echo    - echo args to console
exit    - exit script
ext2load- load binary file from a Ext2 filesystem
ext2ls- list files in a directory (default /)
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
go      - start application at address 'addr'
help    - print online help
ide     - IDE sub-system
iminfo  - print header information for application image
ledfail - Extinguish (0) or light (1) failure LED
loop    - infinite loop on address range
md      - memory display
mm      - memory modify (auto-incrementing)
mtest   - simple RAM test
mw      - memory write (fill)
nand    - NAND sub-system
nboot   - boot from NAND device
nbootup   - boot from NAND device with single bad block skip
nm      - memory modify (constant address)
ping	- send ICMP ECHO_REQUEST to network host
printenv- print environment variables
rarpboot- boot image via network using RARP/TFTP protocol
reset   - Perform RESET of the CPU
run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv  - set environment variables
test    - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
version - print monitor version

Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 19, 2017 12:48PM
ming Wrote:
-------------------------------------------------------
> [root@PogoPlug-Pro]#setenv mtdparts 'mtdparts=410
> 00000.nand:14m(boot),-(data)'
> [root@PogoPlug-Pro]#boot

Execute these commands in serial console, at u-boot prompt (not in Linux).

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 19, 2017 01:02PM
this not u-boot prompt ?
root@PogoPlug:/# reboot
root@PogoPlug:/# [107848.580000] br-lan: port 1(eth0) entering forwarding state
[107848.590000] device eth0 left promiscuous mode
[107848.590000] br-lan: port 1(eth0) entering disabled state
[107848.600000] br-lan: mixed no checksumming and other settings.
[107851.650000] EXT4-fs (sda): re-mounted. Opts: (null)
[107853.740000] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[107853.810000] Restarting system.

NAS7820 BootStrap v0.1 
[Fri Sep 27 08:37:50 CST 2013]
PLX Technology, Inc. 2010. All Rights Reserved
Copyright, lintel 2013.09
CPU Clock set to 700MHz ...
Testing Stage2 Memory...OK!
NAND Flash Info: 
	Vendor ID:0x000000AD
	Product ID:0x000000F1
	Type ID:0x00000000

Reading Nand Flash, Image 0
  Hdr len: 0x00021D30
  Hdr CRC: 0x3A0B1834
 OK


U-Boot 1.1.2 (Sep 23 2013 - 00:30:38)

U-Boot code: 60D00000 -> 60D21D30  BSS: -> 60D56558
RAM Configuration:
	Bank #0: 60000000 128 MB
SRAM Configuration:
	64KB at 0x50000000
NAND:128 MiB
In:    serial
Out:   serial
Err:   serial
Setting Linux mem= boot arg value
Reading upgrade flag from NAND address 0x01ec0000 : 0
Hit any key to stop autoboot:  0 
[root@PogoPlug-Pro]#

Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 19, 2017 01:18PM
ming,

At this point during booting:
Hit any key to stop autoboot:  0

When you type any key on the keyboard, e.g. <Enter>, you will interrupt u-boot, and will be present with a u-boot prompt. Such as this

OX820>

This is the Linux prompt (way past u-boot execution):
[root@PogoPlug-Pro]#

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 19, 2017 02:26PM
I tried many times,but all failed
Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 19, 2017 02:30PM
There is no countdown
Hit any key to stop autoboot:  0
Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 19, 2017 06:40PM
Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 19, 2017 09:55PM
root@PogoPlug:~/tools# ./fw_printenv 
bootcmd=run lightled  root_sata boot_sata || run root_nand boot_nand || run extinguishled
bootdelay=1
baudrate=115200
ethaddr=00:30:e0:00:00:01
ipaddr=192.168.1.200
serverip=192.168.1.100
autoload=n
netmask=255.255.0.0
bootfile="uImage"
load_nand=nboot 0x60500000 0 0x200000
load_nand2=nboot 0x60500000 0 0x440000
lightled=ledfail 1
extinguishled=ledfail 0
boot=bootm 60500000
root_dev=ubi0:rootfs 
root_nand=setenv bootargs root=ubi0:rootfs ubi.mtd=6,512 rootfstype=ubifs rootwait console=ttyS0,115200  mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=128M poweroutage=yes
root_sata=setenv bootargs root=/dev/sda2 ubi.mtd=6,512 rootwaitconsole=ttyS0,115200 mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=128M poweroutage=yes
fload1=fatload ide 0:1 0x60500000 /boot/uImage 
fload2=ext2load ide 0:1 0x60500000 /boot/uImage 
load_hdd=diskboot 0x60500000 0:1
load_hdd2=diskboot 0x60500000 0:2
load_hdd3=diskboot 0x60500000 0:3
reset_sata=ide reset
select0=ide dev 0
select1=ide dev 1
boot_nand=run load_nand boot || run load_nand2 boot
boot_sata=run reset_sata select0 fload1 boot || run reset_sata select0 fload2 boot || run reset_sata select0  load_hdd boot || run reset_sata select0 load_hdd2 boot
stdin=serial
stdout=serial
stderr=serial
bootargs=root=ubi0:rootfs ubi.mtd=6,512 rootfstype=ubifs rootwait  console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=128M poweroutage=yes
root@PogoPlug:~/tools#



Edited 1 time(s). Last edit at 05/19/2017 10:00PM by ming.
Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 20, 2017 06:20AM
ming,

> bootdelay=1

Bootdelay was set to 1 second. So you might have missed it. To interrupt it, pound on the keyboard real quick when you see the u-boot banner.

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 20, 2017 10:03AM
When i type any key on the keyboard, e.g. <Enter>,
NAS7820 BootStrap v0.1 
[Fri Sep 27 08:37:50 CST 2013]
PLX Technology, Inc. 2010. All Rights Reserved
Copyright, lintel 2013.09
CPU Clock set to 700MHz ...
Testing Stage2 Memory...OK!
NAND Flash Info: 
	Vendor ID:0x000000AD
	Product ID:0x000000F1
	Type ID:0x00000000

Reading Nand Flash, Image 0
  Hdr len: 0x00021D30
  Hdr CRC: 0x3A0B1834
 OK


U-Boot 1.1.2 (Sep 23 2013 - 00:30:38)

U-Boot code: 60D00000 -> 60D21D30  BSS: -> 60D56558
RAM Configuration:
	Bank #0: 60000000 128 MB
SRAM Configuration:
	64KB at 0x50000000
NAND:128 MiB
In:    serial
Out:   serial
Err:   serial
Setting Linux mem= boot arg value
Reading upgrade flag from NAND address 0x01ec0000 : 0
Hit any key to stop autoboot:  0 
[root@PogoPlug-Pro]#
[root@PogoPlug-Pro]#

When i miss
root@PogoPlug:/# 
root@PogoPlug:/# reboot
root@PogoPlug:/# [  324.310000] br-lan: port 1(eth0) entering forwarding state
[  324.320000] device eth0 left promiscuous mode
[  324.320000] br-lan: port 1(eth0) entering disabled state
[  324.330000] br-lan: mixed no checksumming and other settings.
[  326.740000] Restarting system.

NAS7820 BootStrap v0.1 
[Fri Sep 27 08:37:50 CST 2013]
PLX Technology, Inc. 2010. All Rights Reserved
Copyright, lintel 2013.09
CPU Clock set to 700MHz ...
Testing Stage2 Memory...OK!
NAND Flash Info: 
	Vendor ID:0x000000AD
	Product ID:0x000000F1
	Type ID:0x00000000

Reading Nand Flash, Image 0
  Hdr len: 0x00021D30
  Hdr CRC: 0x3A0B1834
 OK


U-Boot 1.1.2 (Sep 23 2013 - 00:30:38)

U-Boot code: 60D00000 -> 60D21D30  BSS: -> 60D56558
RAM Configuration:
	Bank #0: 60000000 128 MB
SRAM Configuration:
	64KB at 0x50000000
NAND:128 MiB
In:    serial
Out:   serial
Err:   serial
Setting Linux mem= boot arg value
Reading upgrade flag from NAND address 0x01ec0000 : 0
Hit any key to stop autoboot:  0 
Turn on Green LED.

Reset IDE: Initialising disks
SATA PHY not ready for device 0
SATA PHY not ready for device 1
ide_preinit failed

Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 20, 2017 10:59AM
ming Wrote:
-------------------------------------------------------
> When i type any key on the keyboard, e.g. <Enter>,
>
> NAS7820 BootStrap v0.1
> [Fri Sep 27 08:37:50 CST 2013]
> PLX Technology, Inc. 2010. All Rights Reserved
> Copyright, lintel 2013.09
> CPU Clock set to 700MHz ...
> Testing Stage2 Memory...OK!
> NAND Flash Info:
> Vendor ID:0x000000AD
> Product ID:0x000000F1
> Type ID:0x00000000
> 
> Reading Nand Flash, Image 0
> Hdr len: 0x00021D30
> Hdr CRC: 0x3A0B1834
> OK
> 
> 
> U-Boot 1.1.2 (Sep 23 2013 - 00:30:38)
> 
> U-Boot code: 60D00000 -> 60D21D30  BSS: -> 60D5655
> 8
> RAM Configuration:
> Bank #0: 60000000 128 MB
> SRAM Configuration:
> 64KB at 0x50000000
> NAND:128 MiB
> In:    serial
> Out:   serial
> Err:   serial
> Setting Linux mem= boot arg value
> Reading upgrade flag from NAND address 0x01ec0000
> : 0
> Hit any key to stop autoboot:  0
> [root@PogoPlug-Pro]#
> [root@PogoPlug-Pro]#
> 
>
>
> When i miss
>
> root@PogoPlug:/#
> root@PogoPlug:/# reboot
> root@PogoPlug:/# [  324.310000] br-lan: port 1(eth
> 0) entering forwarding state
> [  324.320000] device eth0 left promiscuous mode
> [  324.320000] br-lan: port 1(eth0) entering disab
> led state
> [  324.330000] br-lan: mixed no checksumming and o
> ther settings.
> [  326.740000] Restarting system.
> 
> NAS7820 BootStrap v0.1
> [Fri Sep 27 08:37:50 CST 2013]
> PLX Technology, Inc. 2010. All Rights Reserved
> Copyright, lintel 2013.09
> CPU Clock set to 700MHz ...
> Testing Stage2 Memory...OK!
> NAND Flash Info:
> Vendor ID:0x000000AD
> Product ID:0x000000F1
> Type ID:0x00000000
> 
> Reading Nand Flash, Image 0
> Hdr len: 0x00021D30
> Hdr CRC: 0x3A0B1834
> OK
> 
> 
> U-Boot 1.1.2 (Sep 23 2013 - 00:30:38)
> 
> U-Boot code: 60D00000 -> 60D21D30  BSS: -> 60D5655
> 8
> RAM Configuration:
> Bank #0: 60000000 128 MB
> SRAM Configuration:
> 64KB at 0x50000000
> NAND:128 MiB
> In:    serial
> Out:   serial
> Err:   serial
> Setting Linux mem= boot arg value
> Reading upgrade flag from NAND address 0x01ec0000
> : 0
> Hit any key to stop autoboot:  0
> Turn on Green LED.
> 
> Reset IDE: Initialising disks
> SATA PHY not ready for device 0
> SATA PHY not ready for device 1
> ide_preinit failed
> 
>

Are you sure your serial console is working? i.e. you can send something, not just only receving the output.

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 20, 2017 11:13AM
I have always used the serial console.telnet can not see
[root@PogoPlug-Pro]#
telnet can only see
root@PogoPlug:/#
Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 20, 2017 09:11PM
[root@PogoPlug-Pro]#version

U-Boot 1.1.2 (Sep 23 2013 - 00:30:38)
[root@PogoPlug-Pro]#bdinfo
arch_number = 0x00000480
env_t       = 0x00000000
boot_params = 0x60000100
DRAM bank   = 0x00000000
-> start    = 0x60000000
-> size     = 0x08000000
ethaddr     = 00:30:E0:00:00:01
ip_addr     = 192.168.1.200
baudrate    = 115200 bps
[root@PogoPlug-Pro]#?
?       - alias for 'help'
base    - print or set address offset
bdinfo  - print Board Info structure
bootm   - boot application image from memory
bootp	- boot image via network using BootP/TFTP protocol
cmp     - memory compare
cp      - memory copy
crc32   - checksum calculation
diskboot- boot from IDE device
echo    - echo args to console
exit    - exit script
ext2load- load binary file from a Ext2 filesystem
ext2ls- list files in a directory (default /)
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
go      - start application at address 'addr'
help    - print online help
ide     - IDE sub-system
iminfo  - print header information for application image
ledfail - Extinguish (0) or light (1) failure LED
loop    - infinite loop on address range
md      - memory display
mm      - memory modify (auto-incrementing)
mtest   - simple RAM test
mw      - memory write (fill)
nand    - NAND sub-system
nboot   - boot from NAND device
nbootup   - boot from NAND device with single bad block skip
nm      - memory modify (constant address)
ping	- send ICMP ECHO_REQUEST to network host
printenv- print environment variables
rarpboot- boot image via network using RARP/TFTP protocol
reset   - Perform RESET of the CPU
run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv  - set environment variables
test    - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
version - print monitor version
[root@PogoPlug-Pro]#

Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 20, 2017 09:33PM
[root@PogoPlug-Pro]#
[root@PogoPlug-Pro]#setenv bootdelay 8
[root@PogoPlug-Pro]#saveenv
Saving Environment to NAND...
Erasing at 0x1a0000 -- 13107200% complete.
OK
 8192 bytes written: OK
Erasing at 0x1c0000 -- 13107200% complete.
OK
 8192 bytes written: OK
Writing to Nand... done
[root@PogoPlug-Pro]#reset
then
root@PogoPlug:/# /root/tools/fw_printenv 
bootcmd=run lightled  root_sata boot_sata || run root_nand boot_nand || run extinguishled
baudrate=115200
ethaddr=00:30:e0:00:00:01
ipaddr=192.168.1.200
serverip=192.168.1.100
autoload=n
netmask=255.255.0.0
bootfile="uImage"
load_nand=nboot 0x60500000 0 0x200000
load_nand2=nboot 0x60500000 0 0x440000
lightled=ledfail 1
extinguishled=ledfail 0
boot=bootm 60500000
root_dev=ubi0:rootfs 
root_nand=setenv bootargs root=ubi0:rootfs ubi.mtd=6,512 rootfstype=ubifs rootwait console=ttyS0,115200  mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=128M poweroutage=yes
root_sata=setenv bootargs root=/dev/sda2 ubi.mtd=6,512 rootwaitconsole=ttyS0,115200 mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=128M poweroutage=yes
fload1=fatload ide 0:1 0x60500000 /boot/uImage 
fload2=ext2load ide 0:1 0x60500000 /boot/uImage 
load_hdd=diskboot 0x60500000 0:1
load_hdd2=diskboot 0x60500000 0:2
load_hdd3=diskboot 0x60500000 0:3
reset_sata=ide reset
select0=ide dev 0
select1=ide dev 1
boot_nand=run load_nand boot || run load_nand2 boot
boot_sata=run reset_sata select0 fload1 boot || run reset_sata select0 fload2 boot || run reset_sata select0  load_hdd boot || run reset_sata select0 load_hdd2 boot
stdin=serial
stdout=serial
stderr=serial
bootargs=root=ubi0:rootfs ubi.mtd=6,512 rootfstype=ubifs rootwait  console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=128M poweroutage=yes
bootdelay=8
root@PogoPlug:/# 

Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 20, 2017 11:43PM
ming,

I see now this u-boot version uses a misleading prompt :) It is a very bad practice to use a similar prompt as a Linux shell for u-boot like this

[root@PogoPlug-Pro]

Now in Linux, your envs show bootdelay=8
> root@PogoPlug:/# /root/tools/fw_printenv
> bootcmd=run lightled  root_sata boot_sata || run r
> oot_nand boot_nand || run extinguishled
> baudrate=115200
> ethaddr=00:30:e0:00:00:01
> ipaddr=192.168.1.200
> serverip=192.168.1.100
> autoload=n
> netmask=255.255.0.0
> bootfile="uImage"
> load_nand=nboot 0x60500000 0 0x200000
> load_nand2=nboot 0x60500000 0 0x440000
> lightled=ledfail 1
> extinguishled=ledfail 0
> boot=bootm 60500000
> root_dev=ubi0:rootfs
> root_nand=setenv bootargs root=ubi0:rootfs ubi.mtd
> =6,512 rootfstype=ubifs rootwait console=ttyS0,115
> 200  mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=128
> M poweroutage=yes
> root_sata=setenv bootargs root=/dev/sda2 ubi.mtd=6
> ,512 rootwaitconsole=ttyS0,115200 mac_adr=0x00,0x3
> 0,0xe0,0x00,0x00,0x01 mem=128M poweroutage=yes
> fload1=fatload ide 0:1 0x60500000 /boot/uImage
> fload2=ext2load ide 0:1 0x60500000 /boot/uImage
> load_hdd=diskboot 0x60500000 0:1
> load_hdd2=diskboot 0x60500000 0:2
> load_hdd3=diskboot 0x60500000 0:3
> reset_sata=ide reset
> select0=ide dev 0
> select1=ide dev 1
> boot_nand=run load_nand boot || run load_nand2 boo
> t
> boot_sata=run reset_sata select0 fload1 boot || ru
> n reset_sata select0 fload2 boot || run reset_sata
> select0  load_hdd boot || run reset_sata select0 l
> oad_hdd2 boot
> stdin=serial
> stdout=serial
> stderr=serial
> bootargs=root=ubi0:rootfs ubi.mtd=6,512 rootfstype
> =ubifs rootwait  console=ttyS0,115200 elevator=cfq
> mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=128M pow
> eroutage=yes
> bootdelay=8
>

So, reboot with serial console connected, and see of the new bootdelay value has resulted in a count down, and whether you can interrupt it.

-bodhi
===========================
Wiki
latest Kirkwood kernel builds and rootfs
latest u-boot-kirkwood builds
latest Oxnas kernel builds and rootfs
latest u-boot-oxnas builds
latest MVEBU Armada kernel builds and rootfs
U-Boot & Kernel Booting process
bodhi's u-boot GitHub
bodhi's corner
Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 21, 2017 01:02AM
I interrupt it.But it does not have this command 'boot'
Reading upgrade flag from NAND address 0x01ec0000 : 0
Hit any key to stop autoboot:  0 
[root@PogoPlug-Pro]#boot
Unknown command 'boot' - try 'help'
[root@PogoPlug-Pro]#
What other command can be replaced it
[root@PogoPlug-Pro]#help
?       - alias for 'help'
base    - print or set address offset
bdinfo  - print Board Info structure
bootm   - boot application image from memory
bootp	- boot image via network using BootP/TFTP protocol
cmp     - memory compare
cp      - memory copy
crc32   - checksum calculation
diskboot- boot from IDE device
echo    - echo args to console
exit    - exit script
ext2load- load binary file from a Ext2 filesystem
ext2ls- list files in a directory (default /)
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
go      - start application at address 'addr'
help    - print online help
ide     - IDE sub-system
iminfo  - print header information for application image
ledfail - Extinguish (0) or light (1) failure LED
loop    - infinite loop on address range
md      - memory display
mm      - memory modify (auto-incrementing)
mtest   - simple RAM test
mw      - memory write (fill)
nand    - NAND sub-system
nboot   - boot from NAND device
nbootup   - boot from NAND device with single bad block skip
nm      - memory modify (constant address)
ping	- send ICMP ECHO_REQUEST to network host
printenv- print environment variables
rarpboot- boot image via network using RARP/TFTP protocol
reset   - Perform RESET of the CPU
run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv  - set environment variables
test    - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
version - print monitor version
Re: Booting Pogo V3 Debian rootfs from OpenWrt u-boot
May 21, 2017 06:05AM
I use tftpd to boot into usb Debian rootfs. Then i flash the new U-boot. Then i flash the new kernel ,then reboot
U-Boot SPL 2013.10-tld-4 (Sep 07 2014 - 14:10:12)
  Boot device: NAND
Attempting to set PLLA to 850 MHz ...
  plla_ctrl0 : 0000020a
  plla_ctrl1 : 00330000
  plla_ctrl2 : 0065008b
  plla_ctrl3 : 000000f1

PLLA Set


U-Boot 2015.10-tld-1 (Nov 21 2015 - 01:17:59 -0800)
OXNAS OX820

DRAM:  128 MiB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   dwmac.40400000
Hit any key to stop autoboot:  0 
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found

Reset IDE: Bus 0: OK 
  Device 0: Model: HGST HTS721010A9E630 Firm: JB0OA3U0 Ser#: JR1000D322ZPJE
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
## Unknown partition table
loading envs from usb 0 ...
** No partition table - usb 0 **

no IDE devices available
running scan_disk ...
Scan device usb
device usb 0:1
** No partition table - usb 0 **
device usb 1:1
** Bad device usb 1 **
device usb 2:1
** Bad device usb 2 **
device usb 3:1
** Bad device usb 3 **
Scan device ide

Reset IDE: Bus 0: OK 
  Device 0: Model: HGST HTS721010A9E630 Firm: JB0OA3U0 Ser#: JR1000D322ZPJE
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
device ide 0:1
** No partition table - ide 0 **
device ide 1:1
** Bad device ide 1 **
device ide 2:1
** Bad device ide 2 **
device ide 3:1
** Bad device ide 3 **
loading uImage ...
** No partition table - usb 0 **
loading uInitrd ...
** No partition table - usb 0 **
loading DTB /boot/dts/ox820-pogoplug-pro.dtb ...
** No partition table - usb 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
resetting ...
Did i miss something
OX820> printenv
bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; reset
bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm 0x60500000 0x60e00000 0x62c00000; else bootm 0x60500000 0x60e00000; fi; else if run load_dtb; then bootm 0x60500000 - 0x62c00000; else bootm 0x60500000; fi; fi
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootdelay=10
bootdev=usb
device=0:1
devices=usb ide
disks=0 1 2 3
dtb_file=/boot/dts/ox820-pogoplug-pro.dtb
ethact=dwmac.40400000
ethaddr=52:3b:20:9c:11:51
if_netconsole=ping $serverip
ipaddr=192.168.0.100
load_dtb=echo loading DTB $dtb_file ...; ext2load $bootdev $device 0x62c00000 $dtb_file
load_initrd=echo loading uInitrd ...; ext2load $bootdev $device 0x60e00000 /boot/uInitrd
load_uimage=echo loading uImage ...; ext2load $bootdev $device 0x60500000 /boot/uImage
mainlineLinux=yes
mtdids=nand0=41000000.nand
mtdparts=mtdparts=41000000.nand:14m(boot),-(data)
preboot=run preboot_nc
preboot_nc=setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi
scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start";  setenv scan_ide "ide reset";  setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if ext2load $dev $disknum:1 0x60500000 /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done
serverip=192.168.0.120
set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
uenv_import=echo importing envs ...; env import -t 0x60500000
uenv_init_devices=setenv init_usb "usb start";  setenv init_ide "ide reset";  setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done;
uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices;  do for disknum in 0; do run uenv_read_disk; done; done;
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x60500000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read;  fi; else if $devtype part $disknum; then run uenv_read; fi;  fi
usb_custom_params=zswap.enabled=1
usb_ready_retry=15

Environment size: 2750/131068 bytes
OX820>
root@debian:~# fdisk -l

Disk /dev/mtdblock0: 14 MB, 14680064 bytes
171 heads, 42 sectors/track, 3 cylinders, total 28672 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0xaaaaaaaa

This doesn't look like a partition table
Probably you selected the wrong device.

          Device Boot      Start         End      Blocks   Id  System
/dev/mtdblock0p1   ?  2863311530  1431655763  1431655765   aa  Unknown
/dev/mtdblock0p2   ?  2863311530  1431655763  1431655765   aa  Unknown
/dev/mtdblock0p3   ?  2863311530       21843   715838805   aa  Unknown
/dev/mtdblock0p4   ?  2863311530  1426085203  1428870485   aa  Unknown

Disk /dev/mtdblock1: 119 MB, 119537664 bytes
255 heads, 63 sectors/track, 14 cylinders, total 233472 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000

Disk /dev/mtdblock1 doesn't contain a valid partition table

Disk /dev/sda: 1000.2 GB, 1000204886016 bytes
255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disk identifier: 0x00000000

Disk /dev/sda doesn't contain a valid partition table

Disk /dev/sdb: 16.2 GB, 16239329280 bytes
64 heads, 32 sectors/track, 15487 cylinders, total 31717440 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000

Disk /dev/sdb doesn't contain a valid partition table
root@debian:~# df -l
Filesystem     1K-blocks   Used Available Use% Mounted on
rootfs          15478792 435760  14250096   3% /
udev               10240      0     10240   0% /dev
tmpfs              12192     76     12116   1% /run
/dev/sdb        15478792 435760  14250096   3% /
tmpfs               5120      0      5120   0% /run/lock
tmpfs              24380      0     24380   0% /run/shm
tmpfs              60956      0     60956   0% /tmp
root@debian:~#



Edited 3 time(s). Last edit at 05/21/2017 09:56AM by ming.
Author:

Your Email:


Subject:


Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: