goflex net problems with uboot

Hi,
I have a goflex net and installed debian together with the new uboot and everything works fine. But now I can not boot into pogoplug again! When no usb drive is connected it does not chainload the original uboot:

U-Boot 2010.09 (Oct 23 2010 - 11:53:10)
Marvell-GoflexNet by Jeff Doozan, Peter Carmichael

SoC:   Kirkwood 88F6281_A0
DRAM:  128 MiB
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot:  0 
(Re)start USB...
USB:   Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported

** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=3"
UBI: MTD device size:            219 MiB
UBI: number of good PEBs:        1751
UBI: number of bad PEBs:         1
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     0
UBI: available PEBs:             1730
UBI: total number of reserved PEBs: 21
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: ........ done.
### JFFS2 load complete: 524288 bytes loaded to 0x800000
## Starting application at 0x00800200 ...

I also downloaded the file to my linux machine and can load it via tftp but the problem still exists. I also downloaded the "
uboot.mtd0.goflexnet.original.kwb" from Jeffs homepage (uboot.mtd0.goflexnet.original.kwb) but a diff shows that the files are identical. The funny thing is, that I can download the uboot for the dockstar and there the chainloading just works without problems:

Marvell>> tftp 0x800000 uboot.mtd0.dockstar.original.kwb
Using egiga0 device
TFTP from server 192.168.1.1; our IP address is 192.168.1.100
Filename 'uboot.mtd0.dockstar.original.kwb'.
Load address: 0x800000
Loading: #################################################################
         ######################################
done
Bytes transferred = 524288 (80000 hex)
Marvell>> go 0x800200
## Starting application at 0x00800200 ...


U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16)

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 00690D60

Soc: MV88F6281 Rev 3 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz 

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 128MB 
DRAM Total size 128MB  16bit width
Flash:  0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB

CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: DISCOVERY:0.1

Streaming disabled 
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME], egiga1
Hit any key to stop autoboot:  0 
CE>>

If I don't hit a key it boots into pogoplug, but if I want to print the environment I just get this:

-sh-3.2# fw_printenv
[   26.710000] JFFS2 compression type 0x07 not available.
[   26.720000] Error: jffs2_decompress returned -5
...

Actually I don't really care for the pogoplug, but it is always the base for installing other systems and I would just like to be able to boot it from uboot via netconsole or serial cable. Any idea what went wrong or how I can boot into pogoplug without loading another uboot? I am not sure if I should flash the original uboot as described here if I cant load it via tftp...

HellG

HellG,

Have you found a solution as of yet? I (still learning & reading here) have Debian installed, but rebooting w/out the Debian HD I get squat too.

i_robot73 Wrote:
-------------------------------------------------------
> HellG,
>
> Have you found a solution as of yet? I (still
> learning & reading here) have Debian installed,
> but rebooting w/out the Debian HD I get squat too.

No, not yet. But I didn't do much research in it recently. Will try again if I have more time.