uboot.mtd0.goflexnet.original.kwb dont start over tftp

knows anyone whats wrong with this ?

U-Boot 2010.09 (Oct 23 2010 - 11:53:10)
Marvell-GoflexNet by Jeff Doozan, Peter Carmichael

SoC:   Kirkwood 88F6281_A0
DRAM:  128 MiB
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot:  0
Marvell>> setenv ipaddr 10.223.8.99
Marvell>> setenv serverip 10.223.8.30
Marvell>> tftp 0x800000 uboot.mtd0.goflexnet.original.kwb
Using egiga0 device
TFTP from server 10.223.8.30; our IP address is 10.223.8.99
Filename 'uboot.mtd0.goflexnet.original.kwb'.
Load address: 0x800000
Loading: ####################################
done
Bytes transferred = 524288 (80000 hex)
Marvell>> go 0x800200
## Starting application at 0x00800200 ...

without tftp i got this boot

U-Boot 2010.09 (Oct 23 2010 - 11:53:10)
Marvell-GoflexNet by Jeff Doozan, Peter Carmichael

SoC:   Kirkwood 88F6281_A0
DRAM:  128 MiB
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot:  0
(Re)start USB...
USB:   Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported

** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=3"
UBI: MTD device size:            219 MiB
UBI: number of good PEBs:        1752
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     0
UBI: available PEBs:             1731
UBI: total number of reserved PEBs: 21
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
NAND read: device 0 offset 0x100000, size 0x400000

i build my uboot but it dont start it hangd also on ## Starting application at 0x00800200 ...
whats my fault ?

my env is

Marvell>> printenv
ethact=egiga0
bootdelay=3
baudrate=115200
mainlineLinux=yes
console=ttyS0,115200
led_init=green blinking
led_exit=green off
led_error=orange blinking
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
mtdids=nand0=orion_nand
partition=nand0,2
rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params
rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
force_rescue=0
force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi
ubifs_mtd=3
ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params
ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi
usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done
usb_scan_list=1 2 3 4
usb_scan_1=usb=0:1 dev=sda1
usb_scan_2=usb=1:1 dev=sdb1
usb_scan_3=usb=2:1 dev=sdc1
usb_scan_4=usb=3:1 dev=sdd1
usb_init=run usb_scan
usb_device=0:1
usb_root=/dev/sda1
usb_rootfstype=ext2
usb_rootdelay=10
usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params
usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot
usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset
ethaddr=00:10:75:26:62:60
rescue_installed=1
arcNumber=3089
stdin=serial
stdout=serial
stderr=serial

Environment size: 2261/131068 bytes

What are you trying to accomplish?

uboot.original.kwb can only boot into the pogoplug environment but looking at your log, it seems that you have replaced the pogoplug environment with the rescue system.

-- Jeff

hi jeff !
thanks for the answer

you have an idea to boot from tftp the entire system
in order to re-flash?
or boot into a rescue system to fix the system onchip
the flash is located to your goflexnet uboot and rescue system

is there any way out that I overlooked?



Edited 1 time(s). Last edit at 02/13/2011 03:52PM by gorgone.

You should be able to follow the directions here to reload the rescue system. After you've done that, however, be aware that you can't change the arcNumber (the current rescue system predates the updated arcNumber support)

See the notes in this thread about the updated uboot.environment url/md5.

-- Jeff



Edited 1 time(s). Last edit at 02/13/2011 09:15PM by Jeff.

Hi gorgone, could you please share your goflexnet partitions data? I'm trying to flash my goflexnet back to stock, but cannot find any instruction how to...

Ben