Stephen P
Help with installing 2016.05 U-Boot Kirkwood for NSA310 October 24, 2017 01:13PM |
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 October 24, 2017 04:12PM |
Admin Registered: 13 years ago Posts: 18,564 |
printenv
Stephen P
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 October 25, 2017 12:14PM |
99 % [....................................] [Type Ctrl-\ + c to quit] U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:59:20 -0700) ZyXEL NSA310 1-Bay Power Media Server SoC: Kirkwood 88F6281_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 PHY reset timed out MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 NSA310> printenv CASset=min CONTRY_TYPE=FF FEATURE_BIT=00 MODEL_ID=A203 PRODUCT_NAME=NSA-310 VENDOR_NAME=ZyXEL Communications Corp. arcNumber=4402 autoload=no baudrate=115200 bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/sda2 init=/bin/systemd bootargs_end=:::DB88FXX81:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=nand read.e 0x2000000 $kernel_addr 0xA00000; bootm 0x2000000 bootdelay=20 bootdev=ide console=console=ttyS0,115200 device=0:2 disL2Cache=no disL2Prefetch=yes disaMvPnp=no dtb_file=/boot/dts/kirkwood-nsa310b-lmsensor-redusbled.dtb enaAutoRecovery=yes enaCpuStream=no enaDCPref=yes enaICPref=yes enaMonExt=no enaWrAllo=no eth1addr=00:19:CB:00:51:82 ethact=egiga0 ethaddr=00:19:CB:00:51:82 fileaddr=1100000 filesize=6e8f80 ipaddr=10.4.50.165 kernel_addr=0xC80000 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 loads_echo=0 machid.bak=118f mainlineLinux=yes mtddevname=key_store mtddevnum=2 mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) nandEcc=1bit netmask=255.255.255.0 partition=nand0,2 root=/dev/sda2 rootdelay=10 rootfstype=ext2 rootpath=/mnt/ARM_FS/ run_diag=yes sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi sata_init=ide reset sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd sata_root=/dev/sda2 serverip=10.4.50.5 set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts stderr=serial stdin=serial stdout=serial uenv_import=echo importing envs ...; env import -t 0x810000 uenv_load=usb start; setenv uenv_loaded 0; for devtype in usb; do for disknum in 0; do run uenv_read_disk; done; done uenv_loaded=0 uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x810000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if $devtype part $disknum; then run uenv_read; fi usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_init=usb start usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd usb_root=/dev/sda1 Environment size: 3211/131068 bytes NSA310> boot NAND read: device 0 offset 0xc80000, size 0xa00000 10485760 bytes read: OK ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-2.6.31.8 Created: 2013-10-01 8:39:59 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5697948 Bytes = 5.4 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... Uncompressing Linux............................................................................................................................................................................................................................................................................ done, booting the kernel.
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 October 25, 2017 05:17PM |
Admin Registered: 13 years ago Posts: 18,564 |
Stephen P
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 October 27, 2017 03:34PM |
Stephen P
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 October 27, 2017 03:39PM |
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 October 27, 2017 05:29PM |
Admin Registered: 13 years ago Posts: 18,564 |
ls -l /sys/class/leds/
Stephen P
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 October 29, 2017 05:15PM |
NSA310> saveenv Saving Environment to NAND... Erasing NAND... Skipping bad block at 0x000c0000 Writing to NAND... FAILED!help? please?
Stephen P
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 October 29, 2017 06:13PM |
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 October 29, 2017 06:55PM |
Admin Registered: 13 years ago Posts: 18,564 |
*** Warning - bad CRC, using default environment
fw_printenv > /boot/uEnv.backup.txt
kirkwood-nsa310.dts This variant is the "original" kirkwood-nsa310a.dts This variant does not have the red USB Led. kirkwood-nsa310b-lmsensor-redusbled.dts There are at least three different NSA310 designs. This 3rd variant has lm85 sensor and red USB Led.
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 October 29, 2017 07:08PM |
Admin Registered: 13 years ago Posts: 18,564 |
i2c@11000 { status = "okay"; adt7476: adt7476a@2e { compatible = "adi,adt7476"; reg = <0x2e>; }; };
i2c@11000 { status = "okay"; lm85: lm85@2e { compatible = "national,lm85"; reg = <0x2e>; }; };
i2c@11000 { status = "okay"; lm85: lm85@2e { compatible = "national,lm85"; reg = <0x2e>; }; };
Stephen P
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 October 30, 2017 09:12PM |
for a in /sys/class/leds/*; do echo heartbeat > $a/trigger; done
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 October 31, 2017 12:23AM |
Admin Registered: 13 years ago Posts: 18,564 |
Stephen P
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 October 31, 2017 10:33AM |
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 October 31, 2017 04:08PM |
Admin Registered: 13 years ago Posts: 18,564 |
Stephen P
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 October 31, 2017 07:41PM |
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:59:20 -0700) ZyXEL NSA310 1-Bay Power Media Server SoC: Kirkwood 88F6281_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 PHY reset timed out MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Reset IDE: Bus 0: OK Bus 1: not available Device 0: Model: ST3320620AS Firm: 3.AAE Ser#: 9QF1Q7M7 Type: Hard Disk Supports 48-bit addressing Capacity: 305245.3 MB = 298.0 GB (625142448 x 512) Unknown command 'mmc' - try 'help' no USB devices available Partition Map for IDE device 0 -- Partition Type: EFI Part Start LBA End LBA Name Attributes Type GUID Partition GUID 1 0x000fb800 0x03b9e7ff "rootfs" attrs: 0x0000000000000000 type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7 guid: 49e23deb-ecf2-43a3-81f8-ca959791d670 2 0x24c2e800 0x2542ea8e "emergency" attrs: 0x0000000000000000 type: 0fc63daf-8483-4772-8e79-3d69d8477de4 guid: 6759cc38-bfb8-42b4-801d-7d77bb19cb8e 3 0x0000003f 0x000fb7ff "system" attrs: 0x0000000000000000 type: 0fc63daf-8483-4772-8e79-3d69d8477de4 guid: 11522420-4034-494c-ba02-ab6dd370e2bb loading envs from ide 0 ... 32 bytes read in 42 ms (0 Bytes/s) Unknown command 'mmc' - try 'help' importing envs ... running scan_disk ... Scan device usb device usb 0:1 ** Bad device usb 0 ** device usb 1:1 ** Bad device usb 1 ** device usb 2:1 ** Bad device usb 2 ** device usb 3:1 ** Bad device usb 3 ** Scan device ide Reset IDE: Bus 0: OK Bus 1: not available Device 0: Model: ST3320620AS Firm: 3.AAE Ser#: 9QF1Q7M7 Type: Hard Disk Supports 48-bit addressing Capacity: 305245.3 MB = 298.0 GB (625142448 x 512) device ide 0:1 1 bytes read in 49 ms (0 Bytes/s) Found bootable drive on ide 0 loading uImage ... 3848064 bytes read in 600 ms (6.1 MiB/s) loading uInitrd ... 7753113 bytes read in 1212 ms (6.1 MiB/s) loading DTB /boot/dts/kirkwood-nsa310a.dtb ... 12458 bytes read in 47 ms (258.8 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: linux-4.13.5-kirkwood-tld-1 Created: 2017-10-24 22:18:01 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3848000 Bytes = 3.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.13.5-kirkwood-tld-1 Created: 2017-10-25 0:27:07 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7753049 Bytes = 7.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 0f3ad000, end 0fb11d59 ... OK Loading Device Tree to 0f3a6000, end 0f3ac0a9 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.13.5-kirkwood-tld-1 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18)) #1 PREEMPT Fri Oct 6 23:54:39 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: ZyXEL NSA310 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) init=/bin/systemd [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 238872K/262144K available (8192K kernel code, 713K rwdata, 2008K rodata, 1024K init, 284K bss, 23272K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0db2744 ( 714 kB) [ 0.000000] .bss : 0xc0db91bc - 0xc0e001d4 ( 285 kB) [ 0.000000] random: get_random_u32 called from cache_alloc_refill+0x378/0x8dc with crng_init=0 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000008] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000043] Switching to timer-based delay loop, resolution 5ns [ 0.000508] Console: colour dummy device 80x30 [ 0.000540] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.000563] pid_max: default: 32768 minimum: 301 [ 0.000750] Security Framework initialized [ 0.000887] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000909] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001744] CPU: Testing write buffer coherency: ok [ 0.002777] Setting up static identity map for 0x100000 - 0x100058 [ 0.003066] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.003323] Hierarchical SRCU implementation. [ 0.006664] devtmpfs: initialized [ 0.010995] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.011023] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.011399] prandom: seed boundary self test passed [ 0.015584] prandom: 100 self tests passed [ 0.015597] pinctrl core: initialized pinctrl subsystem [ 0.016670] NET: Registered protocol family 16 [ 0.017135] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.018604] cpuidle: using governor ladder [ 0.018672] cpuidle: using governor menu [ 0.019183] Feroceon L2: Enabling L2 [ 0.019229] Feroceon L2: Cache support initialised. [ 0.024511] No ATAGs? [ 0.034067] vgaarb: loaded [ 0.034390] SCSI subsystem initialized [ 0.034884] usbcore: registered new interface driver usbfs [ 0.034961] usbcore: registered new interface driver hub [ 0.035042] usbcore: registered new device driver usb [ 0.036222] clocksource: Switched to clocksource orion_clocksource [ 0.126037] VFS: Disk quotas dquot_6.6.0 [ 0.126121] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.136550] NET: Registered protocol family 2 [ 0.137288] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.137327] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.137358] TCP: Hash tables configured (established 2048 bind 2048) [ 0.137438] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.137462] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.137640] NET: Registered protocol family 1 [ 0.138055] RPC: Registered named UNIX socket transport module. [ 0.138068] RPC: Registered udp transport module. [ 0.138075] RPC: Registered tcp transport module. [ 0.138082] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.138333] Unpacking initramfs... [ 0.824362] Freeing initrd memory: 7572K [ 0.824542] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.825472] audit: initializing netlink subsys (disabled) [ 0.825986] Initialise system trusted keyrings [ 0.826036] Key type blacklist registered [ 0.826130] audit: type=2000 audit(0.819:1): state=initialized audit_enabled=0 res=1 [ 0.826215] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 0.826358] zbud: loaded [ 0.827276] NFS: Registering the id_resolver key type [ 0.827304] Key type id_resolver registered [ 0.827313] Key type id_legacy registered [ 0.827332] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.827342] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.827554] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.827752] fuse init (API version 7.26) [ 0.828114] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.828323] orangefs_init: module version upstream loaded [ 0.828334] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 2.556228] random: fast init done [ 6.752738] jitterentropy: Initialization failed with host not compliant with requirements: 2 [ 6.753543] Key type asymmetric registered [ 6.753556] Asymmetric key parser 'x509' registered [ 6.753620] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 6.753632] io scheduler noop registered [ 6.753641] io scheduler deadline registered [ 6.753720] io scheduler cfq registered (default) [ 6.754963] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 6.757267] mvebu-pcie mbus@f1000000:pcie-controller@82000000: PCI host bridge to bus 0000:00 [ 6.757289] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 6.757304] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 6.757318] pci_bus 0000:00: root bus resource [bus 00-ff] [ 6.757678] PCI: bus0: Fast back to back transfers disabled [ 6.757703] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 6.786302] PCI: bus1: Fast back to back transfers disabled [ 6.786373] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 6.786390] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff] [ 6.786410] pci 0000:01:00.0: BAR 6: assigned [mem 0xe0000000-0xe000ffff pref] [ 6.786428] pci 0000:01:00.0: BAR 4: assigned [mem 0xe0010000-0xe0013fff 64bit pref] [ 6.786452] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0014000-0xe0014fff 64bit pref] [ 6.786475] pci 0000:01:00.0: BAR 0: assigned [io 0x10000-0x100ff] [ 6.786491] pci 0000:00:01.0: PCI bridge to [bus 01] [ 6.786504] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff] [ 6.786519] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 6.786632] pcieport 0000:00:01.0: enabling device (0140 -> 0143) [ 6.787157] mv_xor f1060800.xor: Marvell shared XOR driver [ 6.847005] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 6.847236] mv_xor f1060900.xor: Marvell shared XOR driver [ 6.906989] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 6.907436] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 6.908816] console [ttyS0] disabled [ 6.908883] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 7.649757] console [ttyS0] enabled [ 7.660751] loop: module loaded [ 7.664480] sata_mv f1080000.sata: slots 32 ports 2 [ 7.672160] scsi host0: sata_mv [ 7.675766] scsi host1: sata_mv [ 7.679216] ata1: SATA max UDMA/133 irq 32 [ 7.683335] ata2: SATA max UDMA/133 irq 32 [ 7.688248] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1 [ 7.694715] nand: Samsung NAND 128MiB 3,3V 8-bit [ 7.699385] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 7.707017] Scanning device for bad blocks [ 7.809831] 9 cmdlinepart partitions found on MTD device orion_nand [ 7.816130] Creating 9 MTD partitions on "orion_nand": [ 7.821319] 0x000000000000-0x000000100000 : "uboot" [ 7.827436] 0x000000100000-0x000000180000 : "uboot_env" [ 7.833820] 0x000000180000-0x000000200000 : "key_store" [ 7.840291] 0x000000200000-0x000000280000 : "info" [ 7.846150] 0x000000280000-0x000000c80000 : "etc" [ 7.851964] 0x000000c80000-0x000001680000 : "kernel_1" [ 7.858219] 0x000001680000-0x000004640000 : "rootfs1" [ 7.864637] 0x000004640000-0x000005040000 : "kernel_2" [ 7.870995] 0x000005040000-0x000008000000 : "rootfs2" [ 7.878770] libphy: Fixed MDIO Bus: probed [ 7.883778] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.890395] ehci-pci: EHCI PCI platform driver [ 7.894933] ehci-orion: EHCI orion driver [ 7.899199] orion-ehci f1050000.ehci: EHCI Host Controller [ 7.904738] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 7.912671] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 7.946247] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 7.952569] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 7.959441] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.966741] usb usb1: Product: EHCI Host Controller [ 7.971646] usb usb1: Manufacturer: Linux 4.13.5-kirkwood-tld-1 ehci_hcd [ 7.978415] usb usb1: SerialNumber: f1050000.ehci [ 7.983800] hub 1-0:1.0: USB hub found [ 7.987665] hub 1-0:1.0: 1 port detected [ 7.992241] usbcore: registered new interface driver usb-storage [ 7.998665] mousedev: PS/2 mouse device common for all mice [ 8.004839] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 8.011954] i2c /dev entries driver [ 8.018509] hidraw: raw HID events driver (C) Jiri Kosina [ 8.024293] drop_monitor: Initializing network drop monitor service [ 8.030933] NET: Registered protocol family 17 [ 8.035472] Key type dns_resolver registered [ 8.040605] registered taskstats version 1 [ 8.044725] Loading compiled-in X.509 certificates [ 8.049629] zswap: loaded using pool lzo/zbud [ 8.075567] Key type big_key registered [ 8.089268] Key type encrypted registered [ 8.094689] rtc-mv f1010300.rtc: setting system clock to 2017-11-01 00:38:48 UTC (1509496728) [ 8.186274] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl F300) [ 8.256299] ata1.00: native sectors (586072368) is smaller than sectors (625142448) [ 8.264041] ata1.00: ATA-7: ST3320620AS, 3.AAE, max UDMA/133 [ 8.269757] ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 8.336305] ata1.00: configured for UDMA/133 [ 8.346255] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 8.353388] scsi 0:0:0:0: Direct-Access ATA ST3320620AS E PQ: 0 ANSI: 5 [ 8.363098] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB) [ 8.370993] sd 0:0:0:0: [sda] Write Protect is off [ 8.375965] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8.432972] sda: sda1 sda2 sda3 [ 8.438380] sd 0:0:0:0: [sda] Attached SCSI disk [ 8.557930] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 8.564682] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 8.571885] usb 1-1: Product: USB2.0 Hub [ 8.576776] hub 1-1:1.0: USB hub found [ 8.580927] hub 1-1:1.0: 4 ports detected [ 8.697822] ata2: SATA link down (SStatus 0 SControl F300) [ 8.716481] Freeing unused kernel memory: 1024K Loading, please wait... starting version 232 [ 9.142620] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 9.174622] r8169 0000:01:00.0: enabling device (0140 -> 0143) [ 9.201148] r8169 0000:01:00.0 eth0: RTL8168d/8111d at 0xd0d4f000, 00:00:00:00:00:30, XID 083000c0 IRQ 35 [ 9.257725] r8169 0000:01:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 9.615668] r8169 0000:01:00.0 enp1s0: renamed from eth0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.29.2 [/sbin/fsck.ext4 (1) -- /dev/sda1] fsck.ext4 -a -C0 /dev/sda1 rootfs: clean, 19130/1925120 files, 611353/7685632 blocks done. [ 20.189396] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 21.151460] NET: Registered protocol family 10 [ 21.157085] Segment Routing with IPv6 [ 21.190757] ip_tables: (C) 2000-2006 Netfilter Core Team [ 21.255942] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) [ 21.274700] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 9 (stretch)! [ 21.323332] systemd[1]: Set hostname to <mhs1.homead.mainscreen.com>. [ 22.300362] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 22.337257] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 22.376714] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 22.416829] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 22.456637] systemd[1]: Listening on fsck to fsckd communication Socket. [ OK ] Listening on fsck to fsckd communication Socket. [ 22.497366] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [ OK ] Set up automount Arbitrary Executab…rmats File System Automount Point. [ 22.536498] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ OK ] Listening on Journal Audit Socket. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Paths. [ OK ] Reached target Encrypted Volumes. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Created slice System Slice. [ OK ] Created slice system-getty.slice. Mounting POSIX Message Queue File System... Starting Load Kernel Modules... [ OK ] Reached target Slices. Starting Remount Root and Kernel File Systems... Mounting Debug File System... Starting Create list of required st…ce nodes for the current kernel... [ OK ] Created slice system-serial\x2dgetty.slice. [ 23.070847] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro Starting Journal Service... Mounting RPC Pipe File System... Mounting NFSD configuration filesystem... [ OK ] Mounted NFSD configuration filesystem. [ OK ] Mounted RPC Pipe File System. [ OK ] Mounted Debug File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Started Load Kernel Modules. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Create list of required sta…vice nodes for the current kernel. [ OK ] Started Journal Service. Starting Create Static Device Nodes in /dev... Starting Load/Save Random Seed... Starting udev Coldplug all Devices... Starting Flush Journal to Persistent Storage... Mounting FUSE Control File System... Starting Apply Kernel Variables... Starting pNFS block layout mapping daemon... [ OK ] Mounted FUSE Control File System. [ OK ] Started Load/Save Random Seed. [ OK ] Started Apply Kernel Variables. [ OK ] Started pNFS block layout mapping daemon. [ OK ] Started Create Static Device Nodes in /dev. [ 23.997669] systemd-journald[171]: Received request to flush runtime journal from PID 1 [ OK ] Reached target Local File Systems (Pre). Mounting /tmp... Starting udev Kernel Device Manager... [ OK ] Mounted /tmp. [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started udev Coldplug all Devices. [ OK ] Reached target Local File Systems. Starting Raise network interfaces... Starting Create Volatile Files and Directories... Starting Preprocess NFS configuration... [ OK ] Started udev Kernel Device Manager. [ OK ] Started Preprocess NFS configuration. [ OK ] Started Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... [ OK ] Reached target System Time Synchronized. Starting RPC bind portmap service... Starting NFSv4 ID-name mapping service... [ OK ] Reached target NFS client services. [ OK ] Started NFSv4 ID-name mapping service. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ 25.130717] input: gpio_keys as /devices/platform/gpio_keys/input/input0 [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. [ 25.560699] marvell-cesa f1030000.crypto: CESA device successfully registered [ 25.628753] orion_wdt: Initial timeout 21 sec Starting Login Service... Starting Avahi mDNS/DNS-SD Stack... [ OK ] Started RPC bind portmap service. [ OK ] Found device /dev/ttyS0. [ 25.817445] hwmon_vid: Unknown VRM version of your CPU [ OK ] Started Login Service. [ 25.883652] lm85 0-002e: Starting monitoring [ OK ] Reached target RPC Port Mapper. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ 26.027787] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 27.297626] r8169 0000:01:00.0 enp1s0: link down [ 27.302286] r8169 0000:01:00.0 enp1s0: link down [ 27.312039] IPv6: ADDRCONF(NETDEV_UP): enp1s0: link is not ready [ 27.491964] random: crng init done [ 30.115691] r8169 0000:01:00.0 enp1s0: link up [ 30.120217] IPv6: ADDRCONF(NETDEV_CHANGE): enp1s0: link becomes ready [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. Starting OpenBSD Secure Shell server... Starting NFS Mount Daemon... [ OK ] Reached target Network is Online. Starting /etc/rc.local Compatibility... [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started NFS Mount Daemon. Starting NFS server and services... [ 31.332222] NFSD: starting 90-second grace period (net c0d93330) [ OK ] Started NFS server and services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Starting Permit User Sessions... Starting LSB: Start NTP daemon... Starting LSB: Starts syslogd... [ OK ] Started Permit User Sessions. [ 31.687666] r8169 0000:01:00.0 enp1s0: link down [ 31.692346] r8169 0000:01:00.0 enp1s0: link down [ 31.708464] IPv6: ADDRCONF(NETDEV_UP): enp1s0: link is not ready [ OK ] Started LSB: Starts syslogd. [ OK ] Started LSB: Start NTP daemon. Starting LSB: Starts klogd... [ OK ] Started LSB: Starts klogd. [ 34.524230] r8169 0000:01:00.0 enp1s0: link up [ 34.528750] IPv6: ADDRCONF(NETDEV_CHANGE): enp1s0: link becomes ready [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Debian GNU/Linux 9 mhs1.homead.mainscreen.com ttyS0 mhs1 login:
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 October 31, 2017 08:58PM |
Admin Registered: 13 years ago Posts: 18,564 |
Stephen P
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 November 01, 2017 07:36AM |
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:59:20 -0700) ZyXEL NSA310 1-Bay Power Media Server SoC: Kirkwood 88F6281_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 PHY reset timed out MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Reset IDE: Bus 0: OK Bus 1: not available Device 0: Model: ST3320620AS Firm: 3.AAE Ser#: 9QF1Q7M7 Type: Hard Disk Supports 48-bit addressing Capacity: 305245.3 MB = 298.0 GB (625142448 x 512) Unknown command 'mmc' - try 'help' no USB devices available Partition Map for IDE device 0 -- Partition Type: EFI Part Start LBA End LBA Name Attributes Type GUID Partition GUID 1 0x000fb800 0x03b9e7ff "rootfs" attrs: 0x0000000000000000 type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7 guid: 49e23deb-ecf2-43a3-81f8-ca959791d670 2 0x24c2e800 0x2542ea8e "emergency" attrs: 0x0000000000000000 type: 0fc63daf-8483-4772-8e79-3d69d8477de4 guid: 6759cc38-bfb8-42b4-801d-7d77bb19cb8e 3 0x0000003f 0x000fb7ff "system" attrs: 0x0000000000000000 type: 0fc63daf-8483-4772-8e79-3d69d8477de4 guid: 11522420-4034-494c-ba02-ab6dd370e2bb loading envs from ide 0 ... 65 bytes read in 48 ms (1000 Bytes/s) Unknown command 'mmc' - try 'help' importing envs ... running scan_disk ... Scan device usb device usb 0:1 ** Bad device usb 0 ** device usb 1:1 ** Bad device usb 1 ** device usb 2:1 ** Bad device usb 2 ** device usb 3:1 ** Bad device usb 3 ** Scan device ide Reset IDE: Bus 0: OK Bus 1: not available Device 0: Model: ST3320620AS Firm: 3.AAE Ser#: 9QF1Q7M7 Type: Hard Disk Supports 48-bit addressing Capacity: 305245.3 MB = 298.0 GB (625142448 x 512) device ide 0:1 1 bytes read in 49 ms (0 Bytes/s) Found bootable drive on ide 0 loading uImage ... 3848064 bytes read in 600 ms (6.1 MiB/s) loading uInitrd ... 7753113 bytes read in 1196 ms (6.2 MiB/s) loading DTB /boot/dts/kirkwood-nsa310a.dtb ... 12458 bytes read in 47 ms (258.8 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: linux-4.13.5-kirkwood-tld-1 Created: 2017-10-24 22:18:01 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3848000 Bytes = 3.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.13.5-kirkwood-tld-1 Created: 2017-10-25 0:27:07 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7753049 Bytes = 7.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 0f3ad000, end 0fb11d59 ... OK Loading Device Tree to 0f3a6000, end 0f3ac0a9 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.13.5-kirkwood-tld-1 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18)) #1 PREEMPT Fri Oct 6 23:54:39 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: ZyXEL NSA310 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) init=/sbin/init [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 238872K/262144K available (8192K kernel code, 713K rwdata, 2008K rodata, 1024K init, 284K bss, 23272K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0db2744 ( 714 kB) [ 0.000000] .bss : 0xc0db91bc - 0xc0e001d4 ( 285 kB) [ 0.000000] random: get_random_u32 called from cache_alloc_refill+0x378/0x8dc with crng_init=0 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000008] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000043] Switching to timer-based delay loop, resolution 5ns [ 0.000508] Console: colour dummy device 80x30 [ 0.000540] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.000563] pid_max: default: 32768 minimum: 301 [ 0.000750] Security Framework initialized [ 0.000887] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000909] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001744] CPU: Testing write buffer coherency: ok [ 0.002777] Setting up static identity map for 0x100000 - 0x100058 [ 0.003066] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.003323] Hierarchical SRCU implementation. [ 0.006663] devtmpfs: initialized [ 0.011008] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.011036] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.011421] prandom: seed boundary self test passed [ 0.015606] prandom: 100 self tests passed [ 0.015620] pinctrl core: initialized pinctrl subsystem [ 0.016696] NET: Registered protocol family 16 [ 0.017160] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.018632] cpuidle: using governor ladder [ 0.018702] cpuidle: using governor menu [ 0.019215] Feroceon L2: Enabling L2 [ 0.019261] Feroceon L2: Cache support initialised. [ 0.024542] No ATAGs? [ 0.034091] vgaarb: loaded [ 0.034413] SCSI subsystem initialized [ 0.034907] usbcore: registered new interface driver usbfs [ 0.034984] usbcore: registered new interface driver hub [ 0.035065] usbcore: registered new device driver usb [ 0.036245] clocksource: Switched to clocksource orion_clocksource [ 0.126071] VFS: Disk quotas dquot_6.6.0 [ 0.126155] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.136590] NET: Registered protocol family 2 [ 0.137326] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.137365] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.137396] TCP: Hash tables configured (established 2048 bind 2048) [ 0.137477] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.137501] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.137681] NET: Registered protocol family 1 [ 0.138101] RPC: Registered named UNIX socket transport module. [ 0.138114] RPC: Registered udp transport module. [ 0.138122] RPC: Registered tcp transport module. [ 0.138129] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.138379] Unpacking initramfs... [ 0.824450] Freeing initrd memory: 7572K [ 0.824629] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.825565] audit: initializing netlink subsys (disabled) [ 0.826079] Initialise system trusted keyrings [ 0.826131] Key type blacklist registered [ 0.826228] audit: type=2000 audit(0.819:1): state=initialized audit_enabled=0 res=1 [ 0.826439] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 0.826508] zbud: loaded [ 0.827403] NFS: Registering the id_resolver key type [ 0.827434] Key type id_resolver registered [ 0.827443] Key type id_legacy registered [ 0.827461] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.827471] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.827682] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.827882] fuse init (API version 7.26) [ 0.828242] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.828449] orangefs_init: module version upstream loaded [ 0.828460] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 2.556253] random: fast init done [ 6.753021] jitterentropy: Initialization failed with host not compliant with requirements: 2 [ 6.753826] Key type asymmetric registered [ 6.753840] Asymmetric key parser 'x509' registered [ 6.753905] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 6.753917] io scheduler noop registered [ 6.753925] io scheduler deadline registered [ 6.754006] io scheduler cfq registered (default) [ 6.755252] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 6.757562] mvebu-pcie mbus@f1000000:pcie-controller@82000000: PCI host bridge to bus 0000:00 [ 6.757585] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 6.757599] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 6.757614] pci_bus 0000:00: root bus resource [bus 00-ff] [ 6.757974] PCI: bus0: Fast back to back transfers disabled [ 6.757998] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 6.786327] PCI: bus1: Fast back to back transfers disabled [ 6.786399] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 6.786416] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff] [ 6.786437] pci 0000:01:00.0: BAR 6: assigned [mem 0xe0000000-0xe000ffff pref] [ 6.786454] pci 0000:01:00.0: BAR 4: assigned [mem 0xe0010000-0xe0013fff 64bit pref] [ 6.786478] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0014000-0xe0014fff 64bit pref] [ 6.786500] pci 0000:01:00.0: BAR 0: assigned [io 0x10000-0x100ff] [ 6.786517] pci 0000:00:01.0: PCI bridge to [bus 01] [ 6.786530] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff] [ 6.786546] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 6.786660] pcieport 0000:00:01.0: enabling device (0140 -> 0143) [ 6.787186] mv_xor f1060800.xor: Marvell shared XOR driver [ 6.847028] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 6.847260] mv_xor f1060900.xor: Marvell shared XOR driver [ 6.907018] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 6.907464] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 6.908844] console [ttyS0] disabled [ 6.908913] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 7.649613] console [ttyS0] enabled [ 7.660602] loop: module loaded [ 7.664326] sata_mv f1080000.sata: slots 32 ports 2 [ 7.672010] scsi host0: sata_mv [ 7.675609] scsi host1: sata_mv [ 7.679065] ata1: SATA max UDMA/133 irq 32 [ 7.683180] ata2: SATA max UDMA/133 irq 32 [ 7.688100] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1 [ 7.694572] nand: Samsung NAND 128MiB 3,3V 8-bit [ 7.699240] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 7.706873] Scanning device for bad blocks [ 7.809705] 9 cmdlinepart partitions found on MTD device orion_nand [ 7.816003] Creating 9 MTD partitions on "orion_nand": [ 7.821190] 0x000000000000-0x000000100000 : "uboot" [ 7.827321] 0x000000100000-0x000000180000 : "uboot_env" [ 7.833699] 0x000000180000-0x000000200000 : "key_store" [ 7.840167] 0x000000200000-0x000000280000 : "info" [ 7.846020] 0x000000280000-0x000000c80000 : "etc" [ 7.851830] 0x000000c80000-0x000001680000 : "kernel_1" [ 7.858090] 0x000001680000-0x000004640000 : "rootfs1" [ 7.864507] 0x000004640000-0x000005040000 : "kernel_2" [ 7.870865] 0x000005040000-0x000008000000 : "rootfs2" [ 7.878642] libphy: Fixed MDIO Bus: probed [ 7.883648] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.890266] ehci-pci: EHCI PCI platform driver [ 7.894796] ehci-orion: EHCI orion driver [ 7.899061] orion-ehci f1050000.ehci: EHCI Host Controller [ 7.904603] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 7.912533] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 7.946271] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 7.952587] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 7.959453] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.966752] usb usb1: Product: EHCI Host Controller [ 7.971657] usb usb1: Manufacturer: Linux 4.13.5-kirkwood-tld-1 ehci_hcd [ 7.978428] usb usb1: SerialNumber: f1050000.ehci [ 7.983822] hub 1-0:1.0: USB hub found [ 7.987687] hub 1-0:1.0: 1 port detected [ 7.992265] usbcore: registered new interface driver usb-storage [ 7.998694] mousedev: PS/2 mouse device common for all mice [ 8.004870] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 8.011985] i2c /dev entries driver [ 8.018536] hidraw: raw HID events driver (C) Jiri Kosina [ 8.024325] drop_monitor: Initializing network drop monitor service [ 8.030958] NET: Registered protocol family 17 [ 8.035500] Key type dns_resolver registered [ 8.040632] registered taskstats version 1 [ 8.044744] Loading compiled-in X.509 certificates [ 8.049650] zswap: loaded using pool lzo/zbud [ 8.075585] Key type big_key registered [ 8.089328] Key type encrypted registered [ 8.094750] rtc-mv f1010300.rtc: setting system clock to 2017-11-01 11:28:20 UTC (1509535700) [ 8.186297] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl F300) [ 8.256321] ata1.00: native sectors (586072368) is smaller than sectors (625142448) [ 8.264062] ata1.00: ATA-7: ST3320620AS, 3.AAE, max UDMA/133 [ 8.269775] ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 8.336329] ata1.00: configured for UDMA/133 [ 8.346278] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 8.353409] scsi 0:0:0:0: Direct-Access ATA ST3320620AS E PQ: 0 ANSI: 5 [ 8.363123] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB) [ 8.371016] sd 0:0:0:0: [sda] Write Protect is off [ 8.375992] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8.433127] sda: sda1 sda2 sda3 [ 8.438537] sd 0:0:0:0: [sda] Attached SCSI disk [ 8.558042] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 8.564789] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 8.571996] usb 1-1: Product: USB2.0 Hub [ 8.576887] hub 1-1:1.0: USB hub found [ 8.581037] hub 1-1:1.0: 4 ports detected [ 8.697850] ata2: SATA link down (SStatus 0 SControl F300) [ 8.716462] Freeing unused kernel memory: 1024K Loading, please wait... starting version 232 [ 9.142746] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 9.177471] r8169 0000:01:00.0: enabling device (0140 -> 0143) [ 9.184158] r8169 0000:01:00.0 eth0: RTL8168d/8111d at 0xd0d4f000, 00:00:00:00:00:30, XID 083000c0 IRQ 35 [ 9.249100] r8169 0000:01:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 9.621122] r8169 0000:01:00.0 enp1s0: renamed from eth0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.29.2 [/sbin/fsck.ext4 (1) -- /dev/sda1] fsck.ext4 -a -C0 /dev/sda1 rootfs: clean, 18540/1925120 files, 609171/7685632 blocks done. [ 20.106092] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [ ok ] Setting hostname to 'mhs1.homead.mainscreen.com'...done. [....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232 . ok [ ok ] Synthesizing the initial hotplug events...[ 22.585798] input: gpio_keys as /devices/platform/gpio_keys/input/input0 done. [....] Waiting for /dev to be fully populated...[ 22.912883] hwmon_vid: Unknown VRM version of your CPU [ 22.939203] orion_wdt: Initial timeout 21 sec [ 23.079916] marvell-cesa f1030000.crypto: CESA device successfully registered [ 23.095762] sd 0:0:0:0: Attached scsi generic sg0 type 0 done. [ ok ] Activating swap:. [ 24.456425] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ ok ] Will now activate lvm and md swap:done. [info] Will now check all file systems. fsck from util-linux 2.29.2 Checking all file systems. LABEL=rootfs is mounted [....] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that[ ok tion is writable.. [ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done. [ ok . [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables...done. [ ok ] Initializing random number generator...done. [ 26.899405] random: crng init done [ 27.257651] r8169 0000:01:00.0 enp1s0: link down [ 27.262314] r8169 0000:01:00.0 enp1s0: link down [ 28.136656] NET: Registered protocol family 10 [ 28.144694] IPv6: ADDRCONF(NETDEV_UP): enp1s0: link is not ready [ 28.151034] Segment Routing with IPv6 [ 29.588553] r8169 0000:01:00.0 enp1s0: link up [ 29.593048] IPv6: ADDRCONF(NETDEV_CHANGE): enp1s0: link becomes ready [ ok ] Configuring network interfaces...done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1278 (syslogd) . ok [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Starting system message bus: dbus. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [ ok ] Starting NTP server: ntpd. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1276 (klogd) . ok [ ok ] Starting OpenBSD Secure Shell server: sshd. [....] Running local boot scripts (/etc/rc.local)[ 34.787618] r8169 0000:01:00.0 enp1s0: link down [ 34.792284] r8169 0000:01:00.0 enp1s0: link down [ 34.798189] IPv6: ADDRCONF(NETDEV_UP): enp1s0: link is not ready [ 37.585149] r8169 0000:01:00.0 enp1s0: link up [ 37.589674] IPv6: ADDRCONF(NETDEV_CHANGE): enp1s0: link becomes ready . ok Debian GNU/Linux 9 mhs1.homead.mainscreen.com ttyS0 mhs1 login:
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 November 01, 2017 03:47PM |
Admin Registered: 13 years ago Posts: 18,564 |
kirkwood-nsa310a.dts kirkwood-nsa310b-lmsensor-redusbled.dts
ls -l /sys/class/leds
Stephen P
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 November 01, 2017 05:07PM |
root@mhs1:~# ls -l /sys/class/leds total 0 drwxr-xr-x 2 root root 0 Nov 1 22:05 . drwxr-xr-x 41 root root 0 Nov 1 14:06 .. lrwxrwxrwx 1 root root 0 Nov 1 14:06 nsa310:green:copy -> ../../devices/platform/gpio-leds/leds/nsa310:green:copy lrwxrwxrwx 1 root root 0 Nov 1 14:06 nsa310:green:esata -> ../../devices/platform/gpio-leds/leds/nsa310:green:esata lrwxrwxrwx 1 root root 0 Nov 1 14:06 nsa310:green:hdd -> ../../devices/platform/gpio-leds/leds/nsa310:green:hdd lrwxrwxrwx 1 root root 0 Nov 1 14:06 nsa310:green:sys -> ../../devices/platform/gpio-leds/leds/nsa310:green:sys lrwxrwxrwx 1 root root 0 Nov 1 14:06 nsa310:green:usb -> ../../devices/platform/gpio-leds/leds/nsa310:green:usb lrwxrwxrwx 1 root root 0 Nov 1 14:06 nsa310:red:copy -> ../../devices/platform/gpio-leds/leds/nsa310:red:copy lrwxrwxrwx 1 root root 0 Nov 1 14:06 nsa310:red:esata -> ../../devices/platform/gpio-leds/leds/nsa310:red:esata lrwxrwxrwx 1 root root 0 Nov 1 14:06 nsa310:red:hdd -> ../../devices/platform/gpio-leds/leds/nsa310:red:hdd lrwxrwxrwx 1 root root 0 Nov 1 14:06 nsa310:red:sys -> ../../devices/platform/gpio-leds/leds/nsa310:red:sys
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 November 01, 2017 08:32PM |
Admin Registered: 13 years ago Posts: 18,564 |
Stephen P
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 November 01, 2017 10:16PM |
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 November 02, 2017 10:07PM |
Admin Registered: 13 years ago Posts: 18,564 |
Stephen P
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 November 03, 2017 11:54AM |
root@mhs1:~# diff -u /etc/rc.local.orig /etc/rc.local --- /etc/rc.local.orig 2017-10-31 19:08:06.013243388 +0000 +++ /etc/rc.local 2017-11-03 16:49:47.344333640 +0000 @@ -11,6 +11,54 @@ # # By default this script does nothing. +# turn on fan control +if [ -d /sys/class/hwmon/hwmon0/device ]; then + # We appear to have an adt7475 chip / driver + if [ -f /sys/class/hwmon/hwmon0/device/temp1_auto_point1_temp ]; then + echo 30000 > /sys/class/hwmon/hwmon0/device/temp1_auto_point1_temp + echo 50000 > /sys/class/hwmon/hwmon0/device/temp1_auto_point2_temp + echo 80000 > /sys/class/hwmon/hwmon0/device/temp1_crit + fi + if [ -f /sys/class/hwmon/hwmon0/device/temp2_auto_point1_temp ]; then + echo 30000 > /sys/class/hwmon/hwmon0/device/temp2_auto_point1_temp + echo 50000 > /sys/class/hwmon/hwmon0/device/temp2_auto_point2_temp + echo 80000 > /sys/class/hwmon/hwmon0/device/temp2_crit + fi + if [ -f /sys/class/hwmon/hwmon0/device/temp3_auto_point1_temp ]; then + echo 30000 > /sys/class/hwmon/hwmon0/device/temp3_auto_point1_temp + echo 50000 > /sys/class/hwmon/hwmon0/device/temp3_auto_point2_temp + echo 80000 > /sys/class/hwmon/hwmon0/device/temp3_crit + fi + echo 2 > /sys/class/hwmon/hwmon0/device/pwm1_enable + echo 0 > /sys/class/hwmon/hwmon0/device/pwm1_auto_point1_pwm + echo 255 > /sys/class/hwmon/hwmon0/device/pwm1_auto_point2_pwm + echo 0 > /sys/class/hwmon/hwmon0/device/pwm1_stall_disable + echo 7 > /sys/class/hwmon/hwmon0/device/pwm1_auto_channels_temp +elif [ -f /sys/class/hwmon/hwmon0/pwm1_enable ]; then + # We appear to have an LM85 chip / driver + echo 2 > /sys/class/hwmon/hwmon0/pwm1_enable + echo 0 > /sys/class/hwmon/hwmon0/pwm1_auto_pwm_minctl + echo 123 > /sys/class/hwmon/hwmon0/pwm1_auto_channels + if [ -f /sys/class/hwmon/hwmon0/temp1_auto_temp_off ]; then + echo 30000 > /sys/class/hwmon/hwmon0/temp1_auto_temp_off + echo 35000 > /sys/class/hwmon/hwmon0/temp1_auto_temp_min + echo 50000 > /sys/class/hwmon/hwmon0/temp1_auto_temp_max + echo 80000 > /sys/class/hwmon/hwmon0/temp1_auto_temp_crit + fi + if [ -f /sys/class/hwmon/hwmon0/temp2_auto_temp_off ]; then + echo 30000 > /sys/class/hwmon/hwmon0/temp2_auto_temp_off + echo 35000 > /sys/class/hwmon/hwmon0/temp2_auto_temp_min + echo 50000 > /sys/class/hwmon/hwmon0/temp2_auto_temp_max + echo 80000 > /sys/class/hwmon/hwmon0/temp2_auto_temp_crit + fi + if [ -f /sys/class/hwmon/hwmon0/temp3_auto_temp_off ]; then + echo 30000 > /sys/class/hwmon/hwmon0/temp3_auto_temp_off + echo 35000 > /sys/class/hwmon/hwmon0/temp3_auto_temp_min + echo 50000 > /sys/class/hwmon/hwmon0/temp3_auto_temp_max + echo 80000 > /sys/class/hwmon/hwmon0/temp3_auto_temp_crit + fi +fi + # turn on LED if [ -d /sys/class/leds/status:green:health ]; then @@ -70,4 +118,24 @@ echo usb-host > /sys/class/leds/nsa325\:green\:usb/trigger fi +if [ -d /sys/class/leds/nsa310:green:sys ]; then + echo default-on > /sys/class/leds/nsa310\:green\:sys/trigger +fi + +if [ -d /sys/class/leds/nsa310:green:hdd ]; then + echo disk-activity > /sys/class/leds/nsa310\:green\:hdd/trigger +fi + +if [ -d /sys/class/leds/nsa310:green:usb ]; then + echo usb-host > /sys/class/leds/nsa310\:green\:usb/trigger +fi + +if [ -d /sys/class/leds/nsa310:green:esata ]; then + echo ide-disk2 > /sys/class/leds/nsa310\:green\:esata/trigger +fi + +ifdown enp1s0 +/sbin/ifconfig enp1s0 hw ether `fw_printenv -n ethaddr` +ifup enp1s0 + exit 0
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 November 03, 2017 05:21PM |
Admin Registered: 13 years ago Posts: 18,564 |
Stephen P
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 November 03, 2017 07:44PM |
Quote
bodhi
I will also take a look at u-boot to see if something is missing. These LEDs can also be set in the kernel DTS, too, but oftently it is simpler in u-boot.
Stephen P
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 November 03, 2017 07:54PM |
root@mhs1:~# diff -u /etc/rc.local.orig /etc/rc.local --- /etc/rc.local.orig 2017-10-31 19:08:06.013243388 +0000 +++ /etc/rc.local 2017-11-04 00:50:20.066909958 +0000 @@ -11,6 +11,54 @@ # # By default this script does nothing. +# turn on fan control +if [ -d /sys/class/hwmon/hwmon0/device ]; then + # We appear to have an adt7475 chip / driver + if [ -f /sys/class/hwmon/hwmon0/device/temp1_auto_point1_temp ]; then + echo 30000 > /sys/class/hwmon/hwmon0/device/temp1_auto_point1_temp + echo 50000 > /sys/class/hwmon/hwmon0/device/temp1_auto_point2_temp + echo 80000 > /sys/class/hwmon/hwmon0/device/temp1_crit + fi + if [ -f /sys/class/hwmon/hwmon0/device/temp2_auto_point1_temp ]; then + echo 30000 > /sys/class/hwmon/hwmon0/device/temp2_auto_point1_temp + echo 50000 > /sys/class/hwmon/hwmon0/device/temp2_auto_point2_temp + echo 80000 > /sys/class/hwmon/hwmon0/device/temp2_crit + fi + if [ -f /sys/class/hwmon/hwmon0/device/temp3_auto_point1_temp ]; then + echo 30000 > /sys/class/hwmon/hwmon0/device/temp3_auto_point1_temp + echo 50000 > /sys/class/hwmon/hwmon0/device/temp3_auto_point2_temp + echo 80000 > /sys/class/hwmon/hwmon0/device/temp3_crit + fi + echo 7 > /sys/class/hwmon/hwmon0/device/pwm1_auto_channels_temp + echo 2 > /sys/class/hwmon/hwmon0/device/pwm1_enable + echo 0 > /sys/class/hwmon/hwmon0/device/pwm1_auto_point1_pwm + echo 255 > /sys/class/hwmon/hwmon0/device/pwm1_auto_point2_pwm + echo 0 > /sys/class/hwmon/hwmon0/device/pwm1_stall_disable +elif [ -f /sys/class/hwmon/hwmon0/pwm1_enable ]; then + # We appear to have an LM85 chip / driver + echo 2 > /sys/class/hwmon/hwmon0/pwm1_enable + echo 0 > /sys/class/hwmon/hwmon0/pwm1_auto_pwm_minctl + echo 123 > /sys/class/hwmon/hwmon0/pwm1_auto_channels + if [ -f /sys/class/hwmon/hwmon0/temp1_auto_temp_off ]; then + echo 30000 > /sys/class/hwmon/hwmon0/temp1_auto_temp_off + echo 35000 > /sys/class/hwmon/hwmon0/temp1_auto_temp_min + echo 50000 > /sys/class/hwmon/hwmon0/temp1_auto_temp_max + echo 80000 > /sys/class/hwmon/hwmon0/temp1_auto_temp_crit + fi + if [ -f /sys/class/hwmon/hwmon0/temp2_auto_temp_off ]; then + echo 30000 > /sys/class/hwmon/hwmon0/temp2_auto_temp_off + echo 35000 > /sys/class/hwmon/hwmon0/temp2_auto_temp_min + echo 50000 > /sys/class/hwmon/hwmon0/temp2_auto_temp_max + echo 80000 > /sys/class/hwmon/hwmon0/temp2_auto_temp_crit + fi + if [ -f /sys/class/hwmon/hwmon0/temp3_auto_temp_off ]; then + echo 30000 > /sys/class/hwmon/hwmon0/temp3_auto_temp_off + echo 35000 > /sys/class/hwmon/hwmon0/temp3_auto_temp_min + echo 50000 > /sys/class/hwmon/hwmon0/temp3_auto_temp_max + echo 80000 > /sys/class/hwmon/hwmon0/temp3_auto_temp_crit + fi +fi + # turn on LED if [ -d /sys/class/leds/status:green:health ]; then @@ -70,4 +118,24 @@ echo usb-host > /sys/class/leds/nsa325\:green\:usb/trigger fi +if [ -d /sys/class/leds/nsa310:green:sys ]; then + echo default-on > /sys/class/leds/nsa310\:green\:sys/trigger +fi + +if [ -d /sys/class/leds/nsa310:green:hdd ]; then + echo disk-activity > /sys/class/leds/nsa310\:green\:hdd/trigger +fi + +if [ -d /sys/class/leds/nsa310:green:usb ]; then + echo usb-host > /sys/class/leds/nsa310\:green\:usb/trigger +fi + +if [ -d /sys/class/leds/nsa310:green:esata ]; then + echo ide-disk2 > /sys/class/leds/nsa310\:green\:esata/trigger +fi + +ifdown enp1s0 +/sbin/ifconfig enp1s0 hw ether `fw_printenv -n ethaddr` +ifup enp1s0 + exit 0
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 November 03, 2017 08:50PM |
Admin Registered: 13 years ago Posts: 18,564 |
Stephen P
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 November 07, 2017 04:21PM |
root@mhs1:~# apt list --installed | grep -i firmware-realtek WARNING: apt does not have a stable CLI interface. Use with caution in scripts. firmware-realtek/stable,now 20161130-3 all [installed]
mkimage -A arm -O linux -T ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n initramfs-4.13.5-kirkwood-tld-1 -d initrd.img-4.13.5-kirkwood-tld-1 uInitrd
root@mhs1:~# fw_printenv dtb_file dtb_file=/boot/dts/kirkwood-nsa310.dtb
root@mhs1:~# lsmod | grep ^r r8169 69632 0
root@mhs1:~# lshw -c network *-network description: Ethernet interface product: RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: enp1s0 version: 03 serial: 50:67:f0:69:a7:32 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168d-2.fw ip=192.168.1.128 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:35 ioport:10000(size=256) memory:e0014000-e0014fff memory:e0010000-e0013fff memory:e0000000-e000ffff
Stephen P
Re: Help with installing 2016.05 U-Boot Kirkwood for NSA310 November 07, 2017 05:07PM |
[ 6.867955] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000 [ 6.868161] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 9.263807] r8169 0000:01:00.0: assign IRQ: got 35 [ 9.263820] r8169 0000:01:00.0: assigning IRQ 35 [ 9.263832] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 9.294709] r8169 0000:01:00.0: enabling device (0140 -> 0143) [ 9.322395] r8169 0000:01:00.0: enabling Mem-Wr-Inval [ 9.322566] r8169 0000:01:00.0: enabling bus mastering [ 9.323245] r8169 0000:01:00.0 eth0: RTL8168d/8111d at 0xd0d4f000, 00:00:00:00:00:30, XID 083000c0 IRQ 35 [ 9.367453] r8169 0000:01:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 9.751249] r8169 0000:01:00.0 enp1s0: renamed from eth0 [ 29.967937] r8169 0000:01:00.0 enp1s0: link down [ 29.972594] r8169 0000:01:00.0 enp1s0: link down [ 29.981668] IPv6: ADDRCONF(NETDEV_UP): enp1s0: link is not ready [ 32.806395] r8169 0000:01:00.0 enp1s0: link up [ 42.367974] r8169 0000:01:00.0 enp1s0: link down [ 42.372981] r8169 0000:01:00.0 enp1s0: link down [ 45.196829] r8169 0000:01:00.0 enp1s0: link upAccording to the kernel source, some 8168x family chips have a LED frequency that is controlled by the driver, but the 8168d does not. Could the chip be being incorrectly identified? The driver identifies the chipset from the MAC config, so could that relate to the screwy 00:00:00:00:00:30 MAC address the NIC gets by default?