Pogo V4 u-boot - Cannot fw_setenv in Debian

Hi Bodi

Finally i got my pogoplug v4 running again! I'm now trying to setup netconsole.

The thing is only that the commands fw_setenv dont work. Its just setenv. I can boot in debian now and adjusted the /etc/fw_config but it seems its not read during booting. Im missing something (essential knowledge) but dont know what.

Here is the output of my printenv.

Pogov4> printenv
arcNumber=3960
baudrate=115200
bootargs_usb=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial
bootcmd=run bootcmd_uenv; run bootcmd_usb; reset
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot;
bootdelay=10
console=ttyS0,115200
device=0:1
ethact=egiga0
ethaddr=00:25:31:05:23:6c
led_error=orange blinking
led_exit=green off
led_init=green blinking
machid=f78
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
nc_ready=0
partition=nand0,2
rootdelay=10
rootfstype=ext2
set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
stderr=serial
stdin=serial
stdout=serial
uenv_import=echo importing envs ...; env import -t 0x810000
uenv_load=usb start; mmc rescan; ide reset; setenv uenv_loaded 0; for devtype in usb mmc ide; do for disknum in 0; do run uenv_read_disk; done; done
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x810000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read;  fi; else if $devtype part $disknum; then run uenv_read; fi;  fi
usb_boot=mw 0x800000 0 1; run usb_load_uimage; run usb_load_uinitrd; run usb_load_dtb; bootm 0x800000 0x1100000 0x1c00000
usb_init=usb start
usb_load_dtb=ext2load usb $device 0x1c00000 /boot/dts/kirkwood-pogoplug_v4.dtb
usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage
usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd
usb_root=/dev/sda1

and my /etc/fw_config

# MTD device name       Device offset   Env. size       Flash sector size       Number of sectors

/dev/mtd0 0xc0000 0x20000 0x20000

dev: size erasesize name
mtd0: 00100000 00020000 "u-boot"
mtd1: 00400000 00020000 "uImage"
mtd2: 02000000 00020000 "rootfs"
mtd3: 0db00000 00020000 "data"

fw_setenv preboot_nc 'setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi'
fw_setenv preboot 'run preboot_nc'
fw_setenv ipaddr    '192.168.0.25'
fw_setenv serverip '192.168.0.40'

Snarky

-------
mod edit: use code tags



Edited 1 time(s). Last edit at 10/25/2017 09:36AM by bodhi.

Snarky

Shutdon, power up, interrupt serial console and

printenv
boot

Let it boot all the way to Debian. Log in as root, and

cat /etc/fw_env.config 
cat /proc/mtd
ls -lart /boot/dts/kirkwood-pogoplug_v4.dtb

And try to set them again

fw_setenv preboot_nc 'setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi'
fw_setenv preboot 'run preboot_nc'
fw_setenv ipaddr    '192.168.0.25'
fw_setenv serverip '192.168.0.40'

Get the listing

fw_printenv

And post the entire serial console log (from u-boot banner until here).

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Thanks for the quick reply!

I understand now that the fw_ commands are in debian and not in the u_boot console.

Here's the (quit long) output:

U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700)
Pogoplug V4

SoC:   Kirkwood 88F6192_A1
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  128 MiB
MMC:   kwsdio: 0
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Hit any key to stop autoboot:  0
Pogov4> printenv
arcNumber=3960
baudrate=115200
bootargs_usb=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial
bootcmd=run bootcmd_uenv; run bootcmd_usb; reset
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot;
bootdelay=10
console=ttyS0,115200
device=0:1
ethact=egiga0
ethaddr=00:25:31:05:23:6c
led_error=orange blinking
led_exit=green off
led_init=green blinking
machid=f78
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
nc_ready=0
partition=nand0,2
rootdelay=10
rootfstype=ext2
set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
stderr=serial
stdin=serial
stdout=serial
uenv_import=echo importing envs ...; env import -t 0x810000
uenv_load=usb start; mmc rescan; ide reset; setenv uenv_loaded 0; for devtype in usb mmc ide; do for disknum in 0; do run uenv_read_disk; done; done
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x810000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read;  fi; else if $devtype part $disknum; then run uenv_read; fi;  fi
usb_boot=mw 0x800000 0 1; run usb_load_uimage; run usb_load_uinitrd; run usb_load_dtb; bootm 0x800000 0x1100000 0x1c00000
usb_init=usb start
usb_load_dtb=ext2load usb $device 0x1c00000 /boot/dts/kirkwood-pogoplug_v4.dtb
usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage
usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd
usb_root=/dev/sda1

Environment size: 1749/131068 bytes
Pogov4> boot
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found

Reset IDE: ide_preinit failed

Partition Map for USB device 0  --   Partition Type: DOS

Part    Start Sector    Num Sectors     UUID            Type
  1     2048            30226432        477937b2-01     83
loading envs from usb 0 ...
259 bytes read in 420 ms (0 Bytes/s)

no IDE devices available
importing envs ...
## Info: input data size = 260 = 0x104
3821592 bytes read in 572 ms (6.4 MiB/s)
7245696 bytes read in 657 ms (10.5 MiB/s)
10284 bytes read in 775 ms (12.7 KiB/s)
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-4.12.1-kirkwood-tld-1
   Created:      2017-07-20   8:11:24 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3821528 Bytes = 3.6 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
   Image Name:   initramfs-4.12.1-kirkwood-tld-1
   Created:      2017-07-24   0:18:23 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    7245632 Bytes = 6.9 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 01c00000
   Booting using the fdt blob at 0x1c00000
   Loading Kernel Image ... OK
   Loading Ramdisk to 07425000, end 07b0df40 ... OK
   Loading Device Tree to 0741f000, end 0742482b ... OK
Using machid 0xf78 from environment

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.12.1-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] OF: fdt: Machine model: Pogoplug v4
[    0.000000] Memory policy: Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext2 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 109428K/131072K available (8192K kernel code, 716K rwdata, 1972K rodata, 1024K init, 288K bss, 21644K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0900000   (9184 kB)
[    0.000000]       .init : 0xc0c00000 - 0xc0d00000   (1024 kB)
[    0.000000]       .data : 0xc0d00000 - 0xc0db3274   ( 717 kB)
[    0.000000]        .bss : 0xc0db9b9c - 0xc0e01e60   ( 289 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[    0.000012] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[    0.000065] Switching to timer-based delay loop, resolution 6ns
[    0.000768] Console: colour dummy device 80x30
[    0.000820] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666)
[    0.000853] pid_max: default: 32768 minimum: 301
[    0.001149] Security Framework initialized
[    0.001332] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.001362] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.002653] CPU: Testing write buffer coherency: ok
[    0.004227] Setting up static identity map for 0x100000 - 0x100058
[    0.004625] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[    0.009535] devtmpfs: initialized
[    0.015482] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.015522] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.016136] prandom: seed boundary self test passed
[    0.021867] prandom: 100 self tests passed
[    0.021892] pinctrl core: initialized pinctrl subsystem
[    0.023636] NET: Registered protocol family 16
[    0.024414] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.026786] cpuidle: using governor ladder
[    0.026895] cpuidle: using governor menu
[    0.027581] Feroceon L2: Enabling L2
[    0.027646] Feroceon L2: Cache support initialised.
[    0.028195] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[    0.035216] No ATAGs?
[    0.048528] vgaarb: loaded
[    0.048991] SCSI subsystem initialized
[    0.049659] usbcore: registered new interface driver usbfs
[    0.049784] usbcore: registered new interface driver hub
[    0.049904] usbcore: registered new device driver usb
[    0.051615] clocksource: Switched to clocksource orion_clocksource
[    0.183921] VFS: Disk quotas dquot_6.6.0
[    0.184038] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.198933] NET: Registered protocol family 2
[    0.199996] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.200038] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.200069] TCP: Hash tables configured (established 1024 bind 1024)
[    0.200199] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.200234] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.200483] NET: Registered protocol family 1
[    0.201072] RPC: Registered named UNIX socket transport module.
[    0.201089] RPC: Registered udp transport module.
[    0.201099] RPC: Registered tcp transport module.
[    0.201110] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.201446] Unpacking initramfs...
[    1.168849] Freeing initrd memory: 7076K
[    1.169090] NetWinder Floating Point Emulator V0.97 (double precision)
[    1.170461] audit: initializing netlink subsys (disabled)
[    1.171164] Initialise system trusted keyrings
[    1.171244] Key type blacklist registered
[    1.171373] audit: type=2000 audit(1.169:1): state=initialized audit_enabled=0 res=1
[    1.171506] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    1.171684] zbud: loaded
[    1.173130] NFS: Registering the id_resolver key type
[    1.173170] Key type id_resolver registered
[    1.173182] Key type id_legacy registered
[    1.173207] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    1.173222] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    1.173509] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    1.173788] fuse init (API version 7.26)
[    1.174300] orangefs_debugfs_init: called with debug mask: :none: :0:
[    1.174702] orangefs_init: module version upstream loaded
[    1.174718] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[    2.551624] random: fast init done
[    9.945904] Key type asymmetric registered
[    9.945929] Asymmetric key parser 'x509' registered
[    9.946029] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    9.946045] io scheduler noop registered
[    9.946057] io scheduler deadline registered
[    9.946172] io scheduler cfq registered (default)
[    9.947426] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 47
[    9.947451] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 49
[    9.947950] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[    9.950748] mvebu-pcie mbus@f1000000:pcie-controller@82000000: PCI host bridge to bus 0000:00
[    9.950779] pci_bus 0000:00: root bus resource [io  0x1000-0xfffff]
[    9.950799] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[    9.950819] pci_bus 0000:00: root bus resource [bus 00-ff]
[    9.951297] PCI: bus0: Fast back to back transfers disabled
[    9.951333] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    9.981704] PCI: bus1: Fast back to back transfers disabled
[    9.981993] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff]
[    9.982023] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff 64bit]
[    9.982056] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0010000-0xe0010fff 64bit]
[    9.982087] pci 0000:01:00.0: BAR 4: assigned [mem 0xe0011000-0xe0011fff 64bit]
[    9.982115] pci 0000:00:01.0: PCI bridge to [bus 01]
[    9.982140] pci 0000:00:01.0:   bridge window [mem 0xe0000000-0xe00fffff]
[    9.982269] pcieport 0000:00:01.0: enabling device (0140 -> 0142)
[    9.982406] pci 0000:01:00.0: enabling device (0140 -> 0142)
[    9.983128] mv_xor f1060800.xor: Marvell shared XOR driver
[   10.042744] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr )
[   10.043060] mv_xor f1060900.xor: Marvell shared XOR driver
[   10.102767] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr )
[   10.103393] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[   10.105312] console [ttyS0] disabled
[   10.105405] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 10416666) is a 16550A
[   10.814575] console [ttyS0] enabled
[   10.830486] loop: module loaded
[   10.834525] sata_mv f1080000.sata: slots 32 ports 2
[   10.843325] scsi host0: sata_mv
[   10.847096] scsi host1: sata_mv
[   10.850558] ata1: SATA max UDMA/133 irq 32
[   10.854721] ata2: SATA max UDMA/133 irq 32
[   10.860066] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[   10.866501] nand: Hynix H27U1G8F2BTR-BC
[   10.870329] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[   10.877912] Scanning device for bad blocks
[   10.888766] Bad eraseblock 81 at 0x000000a20000
[   10.971327] 5 cmdlinepart partitions found on MTD device orion_nand
[   10.977593] Creating 5 MTD partitions on "orion_nand":
[   10.982741] 0x000000000000-0x000000200000 : "u-boot"
[   10.989544] 0x000000200000-0x000000500000 : "uImage"
[   10.996380] 0x000000500000-0x000000800000 : "uImage2"
[   11.003299] 0x000000800000-0x000001000000 : "failsafe"
[   11.010359] 0x000001000000-0x000008000000 : "root"
[   11.019512] libphy: Fixed MDIO Bus: probed
[   11.024818] libphy: orion_mdio_bus: probed
[   11.036213] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[   11.183268] ata1: SATA link down (SStatus 0 SControl F300)
[   11.533142] ata2: SATA link down (SStatus 0 SControl F300)
[   12.153754] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:05:23:6c
[   12.162652] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   12.169182] ehci-pci: EHCI PCI platform driver
[   12.173733] ehci-orion: EHCI orion driver
[   12.178028] orion-ehci f1050000.ehci: EHCI Host Controller
[   12.183577] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[   12.191447] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
[   12.221664] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[   12.228000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[   12.234809] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   12.242034] usb usb1: Product: EHCI Host Controller
[   12.246898] usb usb1: Manufacturer: Linux 4.12.1-kirkwood-tld-1 ehci_hcd
[   12.253610] usb usb1: SerialNumber: f1050000.ehci
[   12.259271] hub 1-0:1.0: USB hub found
[   12.263162] hub 1-0:1.0: 1 port detected
[   12.267937] xhci_hcd 0000:01:00.0: xHCI Host Controller
[   12.273279] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[   12.282269] xhci_hcd 0000:01:00.0: hcc params 0x200073a1 hci version 0x100 quirks 0x00080010
[   12.290987] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[   12.297796] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   12.305019] usb usb2: Product: xHCI Host Controller
[   12.309883] usb usb2: Manufacturer: Linux 4.12.1-kirkwood-tld-1 xhci-hcd
[   12.316587] usb usb2: SerialNumber: 0000:01:00.0
[   12.322197] hub 2-0:1.0: USB hub found
[   12.325986] hub 2-0:1.0: 2 ports detected
[   12.330719] xhci_hcd 0000:01:00.0: xHCI Host Controller
[   12.336030] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3
[   12.343571] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[   12.351882] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003
[   12.358649] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   12.365877] usb usb3: Product: xHCI Host Controller
[   12.370744] usb usb3: Manufacturer: Linux 4.12.1-kirkwood-tld-1 xhci-hcd
[   12.377579] usb usb3: SerialNumber: 0000:01:00.0
[   12.383158] hub 3-0:1.0: USB hub found
[   12.386944] hub 3-0:1.0: 2 ports detected
[   12.392097] usbcore: registered new interface driver usb-storage
[   12.398582] mousedev: PS/2 mouse device common for all mice
[   12.621663] usb 1-1: new high-speed USB device number 2 using orion-ehci
[   12.815452] usb 1-1: New USB device found, idVendor=18a5, idProduct=0302
[   12.822172] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   12.829313] usb 1-1: Product: STORE N GO
[   12.833252] usb 1-1: Manufacturer: Verbatim
[   12.837424] usb 1-1: SerialNumber: 07014A7E81279C79
[   12.843406] usb-storage 1-1:1.0: USB Mass Storage device detected
[   12.849978] scsi host2: usb-storage 1-1:1.0
[   13.441663] rtc-mv f1010300.rtc: internal RTC not ticking
[   13.447316] i2c /dev entries driver
[   13.452749] hidraw: raw HID events driver (C) Jiri Kosina
[   13.458630] drop_monitor: Initializing network drop monitor service
[   13.465284] NET: Registered protocol family 17
[   13.469826] Key type dns_resolver registered
[   13.475182] registered taskstats version 1
[   13.479269] Loading compiled-in X.509 certificates
[   13.484177] zswap: loaded using pool lzo/zbud
[   13.503259] Key type big_key registered
[   13.520911] Key type encrypted registered
[   13.527120] hctosys: unable to open rtc device (rtc0)
[   13.537233] Freeing unused kernel memory: 1024K
Loading, please wait...
starting version 232
[   13.927982] scsi 2:0:0:0: Direct-Access     Verbatim STORE N GO       5.00 PQ: 0 ANSI: 6
[   13.956418] sd 2:0:0:0: [sda] 30228480 512-byte logical blocks: (15.5 GB/14.4 GiB)
[   13.976291] sd 2:0:0:0: [sda] Write Protect is off
[   13.991758] sd 2:0:0:0: [sda] No Caching mode page found
[   13.997117] sd 2:0:0:0: [sda] Assuming drive cache: write through
[   14.028612]  sda: sda1
[   14.037528] sd 2:0:0:0: [sda] Attached SCSI removable disk
[   14.244314] usbcore: registered new interface driver uas
[   14.326460] mvsdio f1090000.mvsdio: Got CD GPIO
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Warning: fsck not present, so skipping root file system
[   25.036161] EXT2-fs (sda1): warning: mounting ext3 filesystem as ext2
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[ ok ] Setting hostname to 'debian'...done.
[....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232
. ok
[....] Synthesizing the initial hotplug events...[   27.536401] input: gpio_keys as /devices/platform/gpio_keys/input/input0
done.
[....] Waiting for /dev to be fully populated...[   28.028382] orion_wdt: Initial timeout 25 sec
[   28.174941] marvell-cesa f1030000.crypto: CESA device successfully registered
[   28.221864] sd 2:0:0:0: Attached scsi generic sg0 type 0
done.
[ ok ] Activating swap:.
[   29.734565] random: crng init done
[....] Will now check root file system:fsck from util-linux 2.29.2
[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sda1
e2fsck 1.43.4 (31-Jan-2017)
rootfs was not cleanly unmounted, check forced.
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
Free blocks count wrong (3499384, counted=3499383).
Fix? yes


rootfs: ***** FILE SYSTEM WAS MODIFIED *****
rootfs: ***** REBOOT SYSTEM *****
rootfs: 14482/944704 files (8.3% non-contiguous), 278921/3778304 blocks
fsck exited with status code 3
 failed!
[....] The file system check corrected errors on the root partition but requeste[FAILt the system be restarted. ... failed!
[warn] The system will be restarted in 5 seconds. ... (warning).
[info] Will now restart.
[   52.487038] reboot: Restarting system

U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700)
Pogoplug V4

SoC:   Kirkwood 88F6192_A1
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  128 MiB
MMC:   kwsdio: 0
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Hit any key to stop autoboot:  0
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found

Reset IDE: ide_preinit failed

Partition Map for USB device 0  --   Partition Type: DOS

Part    Start Sector    Num Sectors     UUID            Type
  1     2048            30226432        477937b2-01     83
loading envs from usb 0 ...
259 bytes read in 419 ms (0 Bytes/s)

no IDE devices available
importing envs ...
## Info: input data size = 545 = 0x221
3821592 bytes read in 572 ms (6.4 MiB/s)
7245696 bytes read in 656 ms (10.5 MiB/s)
10284 bytes read in 774 ms (12.7 KiB/s)
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-4.12.1-kirkwood-tld-1
   Created:      2017-07-20   8:11:24 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3821528 Bytes = 3.6 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
   Image Name:   initramfs-4.12.1-kirkwood-tld-1
   Created:      2017-07-24   0:18:23 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    7245632 Bytes = 6.9 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 01c00000
   Booting using the fdt blob at 0x1c00000
   Loading Kernel Image ... OK
   Loading Ramdisk to 07425000, end 07b0df40 ... OK
   Loading Device Tree to 0741f000, end 0742482b ... OK
Using machid 0xf78 from environment

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.12.1-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] OF: fdt: Machine model: Pogoplug v4
[    0.000000] Memory policy: Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext2 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 109428K/131072K available (8192K kernel code, 716K rwdata, 1972K rodata, 1024K init, 288K bss, 21644K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0900000   (9184 kB)
[    0.000000]       .init : 0xc0c00000 - 0xc0d00000   (1024 kB)
[    0.000000]       .data : 0xc0d00000 - 0xc0db3274   ( 717 kB)
[    0.000000]        .bss : 0xc0db9b9c - 0xc0e01e60   ( 289 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[    0.000012] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[    0.000066] Switching to timer-based delay loop, resolution 6ns
[    0.000767] Console: colour dummy device 80x30
[    0.000818] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666)
[    0.000852] pid_max: default: 32768 minimum: 301
[    0.001148] Security Framework initialized
[    0.001331] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.001360] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.002649] CPU: Testing write buffer coherency: ok
[    0.004224] Setting up static identity map for 0x100000 - 0x100058
[    0.004621] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[    0.009536] devtmpfs: initialized
[    0.015488] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.015527] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.016141] prandom: seed boundary self test passed
[    0.021873] prandom: 100 self tests passed
[    0.021902] pinctrl core: initialized pinctrl subsystem
[    0.023652] NET: Registered protocol family 16
[    0.024439] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.026802] cpuidle: using governor ladder
[    0.026910] cpuidle: using governor menu
[    0.027595] Feroceon L2: Enabling L2
[    0.027660] Feroceon L2: Cache support initialised.
[    0.028209] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[    0.035243] No ATAGs?
[    0.048570] vgaarb: loaded
[    0.049033] SCSI subsystem initialized
[    0.049704] usbcore: registered new interface driver usbfs
[    0.049828] usbcore: registered new interface driver hub
[    0.049950] usbcore: registered new device driver usb
[    0.051658] clocksource: Switched to clocksource orion_clocksource
[    0.183924] VFS: Disk quotas dquot_6.6.0
[    0.184040] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.198933] NET: Registered protocol family 2
[    0.200000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.200043] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.200073] TCP: Hash tables configured (established 1024 bind 1024)
[    0.200201] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.200236] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.200484] NET: Registered protocol family 1
[    0.201073] RPC: Registered named UNIX socket transport module.
[    0.201090] RPC: Registered udp transport module.
[    0.201100] RPC: Registered tcp transport module.
[    0.201111] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.201450] Unpacking initramfs...
[    1.168743] Freeing initrd memory: 7076K
[    1.168986] NetWinder Floating Point Emulator V0.97 (double precision)
[    1.170363] audit: initializing netlink subsys (disabled)
[    1.171066] Initialise system trusted keyrings
[    1.171149] Key type blacklist registered
[    1.171277] audit: type=2000 audit(1.168:1): state=initialized audit_enabled=0 res=1
[    1.171411] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    1.171510] zbud: loaded
[    1.173045] NFS: Registering the id_resolver key type
[    1.173085] Key type id_resolver registered
[    1.173097] Key type id_legacy registered
[    1.173123] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    1.173137] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    1.173423] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    1.173703] fuse init (API version 7.26)
[    1.174215] orangefs_debugfs_init: called with debug mask: :none: :0:
[    1.174614] orangefs_init: module version upstream loaded
[    1.174631] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[    2.551667] random: fast init done
[    9.945767] Key type asymmetric registered
[    9.945791] Asymmetric key parser 'x509' registered
[    9.945890] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    9.945907] io scheduler noop registered
[    9.945919] io scheduler deadline registered
[    9.946033] io scheduler cfq registered (default)
[    9.947291] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 47
[    9.947316] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 49
[    9.947814] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[    9.950619] mvebu-pcie mbus@f1000000:pcie-controller@82000000: PCI host bridge to bus 0000:00
[    9.950650] pci_bus 0000:00: root bus resource [io  0x1000-0xfffff]
[    9.950670] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[    9.950690] pci_bus 0000:00: root bus resource [bus 00-ff]
[    9.951167] PCI: bus0: Fast back to back transfers disabled
[    9.951203] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    9.981746] PCI: bus1: Fast back to back transfers disabled
[    9.982033] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff]
[    9.982062] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff 64bit]
[    9.982096] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0010000-0xe0010fff 64bit]
[    9.982127] pci 0000:01:00.0: BAR 4: assigned [mem 0xe0011000-0xe0011fff 64bit]
[    9.982155] pci 0000:00:01.0: PCI bridge to [bus 01]
[    9.982180] pci 0000:00:01.0:   bridge window [mem 0xe0000000-0xe00fffff]
[    9.982308] pcieport 0000:00:01.0: enabling device (0140 -> 0142)
[    9.982446] pci 0000:01:00.0: enabling device (0140 -> 0142)
[    9.983173] mv_xor f1060800.xor: Marvell shared XOR driver
[   10.042792] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr )
[   10.043103] mv_xor f1060900.xor: Marvell shared XOR driver
[   10.102808] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr )
[   10.103440] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[   10.105351] console [ttyS0] disabled
[   10.105442] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 10416666) is a 16550A
[   10.814610] console [ttyS0] enabled
[   10.830519] loop: module loaded
[   10.834556] sata_mv f1080000.sata: slots 32 ports 2
[   10.843361] scsi host0: sata_mv
[   10.847133] scsi host1: sata_mv
[   10.850595] ata1: SATA max UDMA/133 irq 32
[   10.854757] ata2: SATA max UDMA/133 irq 32
[   10.860103] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[   10.866540] nand: Hynix H27U1G8F2BTR-BC
[   10.870364] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[   10.877946] Scanning device for bad blocks
[   10.888802] Bad eraseblock 81 at 0x000000a20000
[   10.971346] 5 cmdlinepart partitions found on MTD device orion_nand
[   10.977619] Creating 5 MTD partitions on "orion_nand":
[   10.982774] 0x000000000000-0x000000200000 : "u-boot"
[   10.989578] 0x000000200000-0x000000500000 : "uImage"
[   10.996411] 0x000000500000-0x000000800000 : "uImage2"
[   11.003333] 0x000000800000-0x000001000000 : "failsafe"
[   11.010397] 0x000001000000-0x000008000000 : "root"
[   11.019557] libphy: Fixed MDIO Bus: probed
[   11.024862] libphy: orion_mdio_bus: probed
[   11.036276] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[   11.183310] ata1: SATA link down (SStatus 0 SControl F300)
[   11.533188] ata2: SATA link down (SStatus 0 SControl F300)
[   12.153682] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:05:23:6c
[   12.162583] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   12.169112] ehci-pci: EHCI PCI platform driver
[   12.173664] ehci-orion: EHCI orion driver
[   12.177961] orion-ehci f1050000.ehci: EHCI Host Controller
[   12.183507] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[   12.191378] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
[   12.221705] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[   12.228044] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[   12.234854] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   12.242078] usb usb1: Product: EHCI Host Controller
[   12.246941] usb usb1: Manufacturer: Linux 4.12.1-kirkwood-tld-1 ehci_hcd
[   12.253653] usb usb1: SerialNumber: f1050000.ehci
[   12.259317] hub 1-0:1.0: USB hub found
[   12.263213] hub 1-0:1.0: 1 port detected
[   12.267991] xhci_hcd 0000:01:00.0: xHCI Host Controller
[   12.273329] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[   12.282325] xhci_hcd 0000:01:00.0: hcc params 0x200073a1 hci version 0x100 quirks 0x00080010
[   12.291044] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[   12.297846] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   12.305071] usb usb2: Product: xHCI Host Controller
[   12.309935] usb usb2: Manufacturer: Linux 4.12.1-kirkwood-tld-1 xhci-hcd
[   12.316640] usb usb2: SerialNumber: 0000:01:00.0
[   12.322253] hub 2-0:1.0: USB hub found
[   12.326049] hub 2-0:1.0: 2 ports detected
[   12.330780] xhci_hcd 0000:01:00.0: xHCI Host Controller
[   12.336093] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3
[   12.343631] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[   12.351949] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003
[   12.358719] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   12.365947] usb usb3: Product: xHCI Host Controller
[   12.370813] usb usb3: Manufacturer: Linux 4.12.1-kirkwood-tld-1 xhci-hcd
[   12.377651] usb usb3: SerialNumber: 0000:01:00.0
[   12.383237] hub 3-0:1.0: USB hub found
[   12.387024] hub 3-0:1.0: 2 ports detected
[   12.392175] usbcore: registered new interface driver usb-storage
[   12.398659] mousedev: PS/2 mouse device common for all mice
[   12.621706] usb 1-1: new high-speed USB device number 2 using orion-ehci
[   12.815385] usb 1-1: New USB device found, idVendor=18a5, idProduct=0302
[   12.822107] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   12.829245] usb 1-1: Product: STORE N GO
[   12.833183] usb 1-1: Manufacturer: Verbatim
[   12.837356] usb 1-1: SerialNumber: 07014A7E81279C79
[   12.843341] usb-storage 1-1:1.0: USB Mass Storage device detected
[   12.849898] scsi host2: usb-storage 1-1:1.0
[   13.441708] rtc-mv f1010300.rtc: internal RTC not ticking
[   13.447368] i2c /dev entries driver
[   13.452793] hidraw: raw HID events driver (C) Jiri Kosina
[   13.458669] drop_monitor: Initializing network drop monitor service
[   13.465328] NET: Registered protocol family 17
[   13.469874] Key type dns_resolver registered
[   13.475230] registered taskstats version 1
[   13.479313] Loading compiled-in X.509 certificates
[   13.484223] zswap: loaded using pool lzo/zbud
[   13.503140] Key type big_key registered
[   13.520638] Key type encrypted registered
[   13.526858] hctosys: unable to open rtc device (rtc0)
[   13.536971] Freeing unused kernel memory: 1024K
Loading, please wait...
starting version 232
[   13.927913] scsi 2:0:0:0: Direct-Access     Verbatim STORE N GO       5.00 PQ: 0 ANSI: 6
[   13.956569] sd 2:0:0:0: [sda] 30228480 512-byte logical blocks: (15.5 GB/14.4 GiB)
[   13.974847] sd 2:0:0:0: [sda] Write Protect is off
[   13.991798] sd 2:0:0:0: [sda] No Caching mode page found
[   13.997151] sd 2:0:0:0: [sda] Assuming drive cache: write through
[   14.028545]  sda: sda1
[   14.037591] sd 2:0:0:0: [sda] Attached SCSI removable disk
[   14.275292] usbcore: registered new interface driver uas
[   14.358836] mvsdio f1090000.mvsdio: Got CD GPIO
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Warning: fsck not present, so skipping root file system
[   25.036093] EXT2-fs (sda1): warning: mounting ext3 filesystem as ext2
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[ ok ] Setting hostname to 'debian'...done.
[....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232
. ok
[....] Synthesizing the initial hotplug events...[   27.520435] input: gpio_keys as /devices/platform/gpio_keys/input/input0
done.
[....] Waiting for /dev to be fully populated...[   27.997447] orion_wdt: Initial timeout 25 sec
[   28.151236] marvell-cesa f1030000.crypto: CESA device successfully registered
[   28.219930] sd 2:0:0:0: Attached scsi generic sg0 type 0
done.
[ ok ] Activating swap:.
[   29.712618] random: crng init done
[....] Will now check root file system:fsck from util-linux 2.29.2
[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sda1
e2fsck 1.43.4 (31-Jan-2017)
rootfs: clean, 14482/944704 files, 278921/3778304 blocks
. ok
[ ok ] Will now activate lvm and md swap:done.
[info] Will now check all file systems.
fsck from util-linux 2.29.2
Checking all file systems.
LABEL=rootfs is mounted
[....] Done checking file systems. A log is being saved in /var/log/fsck/checkfs[ ok hat location is writable..
[ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done.
[ ok .
[ ok ] Will now mount local filesystems:.
[ ok ] Will now activate swapfile swap:done.
[ ok ] Checking minimum space in /tmp...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables...done.
[ ok ] Initializing random number generator...done.
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5
Copyright 2004-2016 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Listening on LPF/eth0/00:25:31:05:23:6c
Sending on   LPF/eth0/00:25:31:05:23:6c
Sending on   Socket/fallback
DHCPREQUEST of 192.168.0.14 on eth0 to 255.255.255.255 port 67
[  113.979350] NET: Registered protocol family 10
[  113.987339] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[  113.993508] Segment Routing with IPv6
DHCPREQUEST of 192.168.0.14 on eth0 to 255.255.255.255 port 67
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 10
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 14
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 19
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 13
No DHCPOFFERS received.
Trying recorded lease 192.168.0.14
PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data.

--- 192.168.0.1 ping statistics ---
1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms

No working leases in persistent database - sleeping.
done.
[ ok ] Starting RPC port mapper daemon: rpcbind.
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1315 (syslogd)
. ok
[ ok ] Starting system message bus: dbus.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting NFS common utilities: statd idmapd.
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting NTP server: ntpd.
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1318 (klogd)
. ok
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[ ok ] Running local boot scripts (/etc/rc.local).

Debian GNU/Linux 9 debian ttyS0

debian login: root
Password:
Last login: Wed Dec 31 16:03:21 PST 1969 on ttyS0
Linux debian 4.12.1-kirkwood-tld-1 #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017 armv5tel

The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.

Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
root@debian:~# cat /etc/fw_env.config
# MTD device name       Device offset   Env. size       Flash sector size      Number of sectors

/dev/mtd0 0xc0000 0x20000 0x20000

dev: size erasesize name
mtd0: 00100000 00020000 "u-boot"
mtd1: 00400000 00020000 "uImage"
mtd2: 02000000 00020000 "rootfs"
mtd3: 0db00000 00020000 "data"

fw_setenv preboot_nc 'setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi'
fw_setenv preboot 'run preboot_nc'
fw_setenv ipaddr    '192.168.0.25'
fw_setenv serverip '192.168.0.40'
root@debian:~# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00200000 00020000 "u-boot"
mtd1: 00300000 00020000 "uImage"
mtd2: 00300000 00020000 "uImage2"
mtd3: 00800000 00020000 "failsafe"
mtd4: 07000000 00020000 "root"
root@debian:~# ls -lart /boot/dts/kirkwood-pogoplug_v4.dtb
-rw-r--r-- 1 root root 10284 Jul 16  2017 /boot/dts/kirkwood-pogoplug_v4.dtb
root@debian:~#

Edited 1 time(s). Last edit at 10/25/2017 05:10PM by bodhi.

Please use code tags next time to post log. It is very hard to read without it. Hope you know how to use code tags?

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Snarky,

At this point, I need to see the actual log of what going on. How you executed them, and all the outputs. So after you execute these commands, please copy everything on your terminal begining here until the end and post here. Your u-boot envs are incorrect, so I need to know why.

In Debian.

ls -lart /boot
cat /etc/fw_env.config 
cat /proc/mtd
ls -lart /boot/dts/kirkwood-pogoplug_v4.dtb
fw_setenv preboot_nc 'setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi'
fw_setenv preboot 'run preboot_nc'
fw_setenv ipaddr    '192.168.0.25'
fw_setenv serverip '192.168.0.40'
fw_printenv

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)



Edited 1 time(s). Last edit at 10/25/2017 05:27PM by bodhi.

Hi Bodhi,

I'm quite new to this and never used code tags. A very basic thing i guess but im not a programmer. (also i tried to change my username cause i didnt know what it meant till just a few moments ago).

ls -lart /boot
total 36264
drwxr-xr-x  2 root root    4096 Jul 15 15:14 dts
-rw-r--r--  1 root root  153501 Jul 15 20:21 config-4.12.1-kirkwood-tld-1
-rwxr-xr-x  1 root root 3821528 Jul 15 21:42 zImage-4.12.1-kirkwood-tld-1
-rw-------  1 root root 3821528 Jul 16 00:43 vmlinuz-4.12.1-kirkwood-tld-1
-rw-------  1 root root 2504031 Jul 16 00:43 System.map-4.12.1-kirkwood-tld-1
-rw-r--r--  1 root root 8435004 Jul 16 01:06 linux-headers-4.12.1-kirkwood-tld-1_1.0_armel.deb
-rw-r--r--  1 root root 3821592 Jul 20 01:11 uImage
-rw-r--r--  1 root root 7245632 Jul 23 17:15 initrd.img-4.12.1-kirkwood-tld-1
-rw-r--r--  1 root root 7245696 Jul 23 17:18 uInitrd
-rw-r--r--  1 root root     259 Oct 16 05:42 uEnv.txt
drwxr-xr-x  3 root root    4096 Oct 16 05:42 .
drwxr-xr-x 23 root root    4096 Oct 25 03:51 ..

cat /etc/fw_env.config
# MTD device name       Device offset   Env. size       Flash sector size      Number of sectors

/dev/mtd0 0xc0000 0x20000 0x20000

#dev: size erasesize name
mtd0: 00100000 00020000 "u-boot"
#mtd1: 00400000 00020000 "uImage"
#mtd2: 02000000 00020000 "rootfs"
#mtd3: 0db00000 00020000 "data"

#fw_setenv preboot_nc 'setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi'
#fw_setenv preboot 'run preboot_nc'
#fw_setenv ipaddr    '192.168.0.25'
# fw_setenv serverip '192.168.0.40'

i commented out some stuff to try

cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00200000 00020000 "u-boot"
mtd1: 00300000 00020000 "uImage"
mtd2: 00300000 00020000 "uImage2"
mtd3: 00800000 00020000 "failsafe"
mtd4: 07000000 00020000 "root"

mtd0 is not right but cant get it set to be the right values.

 ls -lart /boot/dts/kirkwood-pogoplug_v4.dtb
-rw-r--r-- 1 root root 10284 Jul 16 01:08 /boot/dts/kirkwood-pogoplug_v4.dtb

 fw_setenv preboot_nc 'setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi'
Environment does not start on (erase) block boundary
Error: environment not initialized

fw_setenv preboot 'run preboot_nc'
Environment does not start on (erase) block boundary
Error: environment not initialized

 fw_setenv ipaddr    '192.168.0.25'
Environment does not start on (erase) block boundary
Error: environment not initialized

fw_setenv serverip '192.168.0.40'
Environment does not start on (erase) block boundary
Error: environment not initialized

 fw_printenv
Environment does not start on (erase) block boundary

I hope i did the tagging right.
It's obvious that environment is not initialized. Environment is something that you can instruct to do some basic commands like setting the ip-address and such right? It's got something to do with the boundary on mtd0. Unfortunately my knowledge about boundarys and mtd is near zero. I've read your section about the booting process and i understand the principle. I just dont know the basics. I think i can say i'm a noob.

Snarky

Snarky,


1. Code tags button is the right most button on top of the text box where you type your post (the B button for bold is the left most).

2. You also did not post the log of commands and their output. When I ask for that, you should copy/paste the entire screen to the post. Don't reformat anything.

Since you are new with this, you don't know that the log must be shown as is. The reason is everything is important (including where you are in the root file system, are you root,....), and only the log captured verbatim would show that without me asking for each details.

For example:

root@tldDebian:~# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00100000 00020000 "uboot"
mtd1: 00080000 00020000 "uboot_env"

3. Your envs are a little bit messed up. So I will come back later today and show you how to fix them.

4. In the mean time, please execute these 2 commands and post the output:

cat /etc/fw_env.config
cat /proc/mtd

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)



Edited 1 time(s). Last edit at 10/30/2017 02:11PM by bodhi.

Hi Bodhi,

I lost contact via ssh and the serial cable got loose. While soldering i managed to brick it totally. Luckily I've got another fresh one lying around. I'll start allover again, now with more knowledge than zero.

Cheers,

Maarten

Maarten,

That's a bummer :) BTW, the solder buttons are quite soft, you can use small pins and push them in temporarily to connect. And then later use a JST header instead of just wires.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Hi Bodhi,

Didnt read your post about the soft solder buttons. But i managed to solder some wires on and directly put some hotglue on it. So now im all setup for a new try! In the meanwhile ive found the pdf about u-boot. Im wondering if its not possible to let the stock uboot boot to usb. That would off course be a lot easier. But something is telling me its not that easy :-)

I've set up a server with my own nextcloud with a raid zfs filesystem and wanted to make my pogoplug the backupserver. Setting up the pogoplug is a lot more work in the meantime. But it's fun doing it!

Maarten

> Im wondering if its not
> possible to let the stock uboot boot to usb. That
> would off course be a lot easier. But something is
> telling me its not that easy :-)
>

I'd recommend to install new u-boot, if you plan to boot with the latest Debian on USB. Running stock u-boot is possible of course, but it is too limited to be useful.

With this box, you can boot with kwboot so it is almost unbrickable (if serial console is working, you can always recover from any problem).

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Hi Bodhi,

I know it's almost unbrickable (unless you overheat something with a seemingly small yet giant soldering iron).

I tried to activate ssh access via the website of pogoplug but the checkbox ssh access under security settings wasn't there anymore. But I managed to automatically startup the ssh daemon, dropbear. Makes life a bit easier. The first thing i had to do was remount the system because it's mounted in read only. Then i could adjust /etc/inittab to startup dropbear at boottime. Also i could copy the tools in the bin directory. For future reference:


For pogoplug series 4 v4-a3-01 remounting in read/write:

mount -o remount,rw -t ubifs ubi0:rootfs /

Adjusting inittab to start dropbear at boottime. Added line3.

/ # vi /etc/inittab

:qsysinit:/etc/init.d/rcS
::respawn:-/bin/sh
:2345:respawn:/usr/sbin/dropbear

#::respawn:-/bin/sh
#tty2::askfirst:-/bin/sh
#::ctrlaltdel:/bin/umount -a -r


Grtz,

Maarten

> I know it's almost unbrickable (unless you
> overheat something with a seemingly small yet
> giant soldering iron).

:))


> I tried to activate ssh access via the website of
> pogoplug but the checkbox ssh access under
> security settings wasn't there anymore. But I
> managed to automatically startup the ssh daemon,
> dropbear. Makes life a bit easier. The first thing
> i had to do was remount the system because it's
> mounted in read only. Then i could adjust
> /etc/inittab to startup dropbear at boottime. Also
> i could copy the tools in the bin directory. For
> future reference:
>
>
> For pogoplug series 4 v4-a3-01 remounting in
> read/write:
>
>

> mount -o remount,rw -t ubifs ubi0:rootfs /
>

>
> Adjusting inittab to start dropbear at boottime.
> Added line3.
>
>
> / # vi /etc/inittab
>
> :qsysinit:/etc/init.d/rcS
> ::respawn:-/bin/sh
> :2345:respawn:/usr/sbin/dropbear
>
> #::respawn:-/bin/sh
> #tty2::askfirst:-/bin/sh
> #::ctrlaltdel:/bin/umount -a -r


Cool! another nifty way to activate dropbear.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Hi Bodhi,

Finally i had time to test uart booting. Unfortunately this doesnt work.

kwboot-tool#

 ./kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.pogo_v4.mtd0.kwb -p
Sending boot message. Please reboot the target.../
Sending boot image...
  0 % [.+.+xmodem: Protocol error

without the -p flag

./kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.pogo_v4.mtd0.kwb
Sending boot message. Please reboot the target...\
Sending boot image...
xmodem: Bad message

First i run the code and then powerup the pogoplug. The serial is working.

Am i doing something wrong?

Cheers,

Maarten

Maarten,

./kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.pogo_v4.mtd0.kwb -p

> Sending boot message. Please reboot the
> target.../
> Sending boot image...
> 0 % [.+.+xmodem: Protocol error

This actually looks good. It's the Pogo V4 quirk. You need to recall (up arrow) the kwboot command above and execute it again, repeatedly a few times, until the handshake occurs. It could take up to 20 times before kwboot successfully handshakes with the box.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Hi Bodhi,

Finally I succeeded! Thanks a lot for your help! Netconsole is also working. Nice that thatś possible at such a low level.

I think i messed up the first time because i thought the B section was not obligatory. Also i did the backup of the current_envs and i got an "crc error using default something" But i was impatient.

Its working now! . Now i can setup the rest of my network! Thanks again!

Cheers!

Maarten

Maarten,

Cool!

I've revised the instruction in the latest u-boot version to inlcude section B directly, so that people don't overlook it (in the past it was necessary to separate it).

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)