armada 370 (88f6710) mainline uboot support
Posted by wacke
|
Re: armada 370 (88f6710) mainline uboot support January 29, 2021 05:54AM |
Admin Registered: 13 years ago Posts: 18,548 |
wacke,
I think we need to look at your flash type and mtdparts variable. Bootargs need correct mtdparts definition and also the kernel boot log will tell us what type of flash you have.
So power up interrupt serial console,
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 01/29/2021 05:55AM by bodhi.
Quote
Unsupported flash type 8 on /dev/mtd1
I think we need to look at your flash type and mtdparts variable. Bootargs need correct mtdparts definition and also the kernel boot log will tell us what type of flash you have.
So power up interrupt serial console,
help printenvand boot
bootAnd then please post the serial console log here. I think I saw your boot log before, but let's get the most recent one.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 01/29/2021 05:55AM by bodhi.
|
Re: armada 370 (88f6710) mainline uboot support January 29, 2021 10:05AM |
Registered: 8 years ago Posts: 166 |
Hi bodhi,
Uboot env:
And the boot log:
Uboot env:
BootROM 1.08
Booting from NAND flash
General initialization - Version: 1.0.0
High speed PHY - Version: 2.1.3 (COM-PHY-V20)
Update PEX Device ID 0x67100
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver 5.5.1
DDR3 Training Sequence - Run without PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12 (Jan 27 2021 - 10:27:11) RTNAS V3 2013_Q2.0
Board: RD-88F6710
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 200 [MHz]
DDR @ 600 [MHz]
DDR 16Bit Width, FastPath Memory Access
DRAM: 1 GiB
Port0: phyAddr=0x0, Not Marvell PHY id1 ffff id2 ffff
Map: Code: 0x3fef3000:0x3ff90674
BSS: 0x3ffef628
Stack: 0x3f9f2ef8
Heap: 0x3f9f3000:0x3fef3000
NAND: (ID 0x682c) 4096 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 1048320, version 0x01
Bad block table found at page 1048064, version 0x01
nand_read_bbt: Bad block at 0x000001680000
nand_read_bbt: Bad block at 0x0000016c0000
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 1.1
PEX 1: Root Complex Interface, Detected Link X1, GEN 1.1
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Modules/Interfaces Detected:
SDIO
RGMII1 Switch module
PEX0 (Lane 0)
PEX1 (Lane 1)
SATA0 (Lane 2)
SATA1 (Lane 3)
Net: egiga1 [PRIME]
Hit any key to stop autoboot: 0
Marvell>> <INTERRUPT>
Marvell>> <INTERRUPT>
Marvell>> help
? - alias for 'help'
SatR - Sample At Reset sub-system
base - print or set address offset
bdinfo - print Board Info structure
boot - boot default, i.e., run 'bootcmd'
bootd - boot default, i.e., run 'bootcmd'
bootelf - Boot from an ELF image in memory
bootm - boot application image from memory
bootp - boot image via network using BOOTP/TFTP protocol
bootvx - Boot vxWorks from an ELF image
bubt - bubt - Burn an image on the Boot Flash.
chpart - change active partition
cmp - memory compare
coninfo - print console devices and information
cp - memory copy
crc32 - checksum calculation
date - get/set/reset date & time
ddrPhyRead- ddrPhyRead - Read DDR PHY register
ddrPhyWrite- ddrPhyWrite - Write DDR PHY register
dhcp - boot image via network using DHCP/TFTP protocol
diskboot- diskboot- boot from IDE device
dma - dma - Perform DMA using the XOR engine
echo - echo args to console
editenv - edit environment variable
eeprom - EEPROM sub-system
env - environment handling commands
exit - exit script
ext2load- load binary file from a Ext2 filesystem
ext2ls - list files in a directory (default /)
ext4load- load binary file from a Ext4 filesystem
ext4ls - list files in a directory (default /)
ext4write- create a file in the root directory
false - do nothing, unsuccessfully
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls - list files in a directory (default /)
fdt - flattened device tree utility commands
fsinfo - print information about filesystems
fsload - load binary file from a filesystem image
go - start application at address 'addr'
help - print command description/usage
i2c - I2C sub-system
ide - ide - IDE sub-system
iminfo - print header information for application image
imxtract- extract a part of a multi-image
ir - ir - reading and changing MV internal register values.
itest - return true/false on integer compare
loadb - load binary file over serial line (kermit mode)
loads - load S-Record file over serial line
loadx - load binary file over serial line (xmodem mode)
loady - load binary file over serial line (ymodem mode)
loop - infinite loop on address range
ls - list files in a directory (default /)
lump - lump - Wait for a LUMP
map - map - Display address decode windows
md - memory display
me - me - PCI master enable
mm - memory modify (auto-incrementing address)
mmc - MMC sub system
mmcinfo - display MMC info
mp - mp - map PCI BAR
mtdparts- define flash/nand partitions
mtest - simple RAM read/write test
mw - memory write (fill)
nand - NAND sub-system
nboot - boot from NAND device
nfs - boot image via network using NFS protocol
nm - memory modify (constant address)
pci - list and access PCI Configuration Space
pciePhyRead- phyRead - Read PCI-E Phy register
pciePhyWrite- pciePhyWrite - Write PCI-E Phy register
phyRead - phyRead - Read Phy register
phyWrite- phyWrite - Write Phy register
phydump - Dump all the registers/pages for a given PHY
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
pxe - commands to get and boot from pxe files
rcvr - rcvr - Satrt recovery process (Distress Beacon with TFTP server)
reset - Perform RESET of the CPU
resetenv- resetenv - earse environment sector to reset all variables to default.
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
scsi - SCSI sub-system
scsiboot- boot from SCSI device
se - se - PCI Slave enable
setenv - set environment variables
sf - SPI flash sub-system
sg - sg - scanning the PHYs status
showvar - print local hushshell variables
sleep - delay execution for some time
source - run script from memory
sp - scan and detect all devices on mvPCI interface
sspi - SPI utility command
switchCountersRead- switchCntPrint - Read switch port counters.
switchPhyRegRead- - Read switch register
switchPhyRegWrite- - Write switch register
switchRegRead- switchRegRead - Read switch register
switchRegWrite- switchRegWrite - Write switch register
temp - temp - Display the device temperature.
tempCmd0- tempCmd - This command allocated for monitor extinction
tempCmd1- tempCmd - This command allocated for monitor extinction
tempCmd2- tempCmd - This command allocated for monitor extinction
tempCmd3- tempCmd - This command allocated for monitor extinction
test - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
training- training - prints the results of the DDR3 Training.
true - do nothing, successfully
ts_report- ts_report - report touch screen cooridate
ts_test - ts_test - test touch screen
ubi - ubi commands
ubifsload- load file from an UBIFS filesystem
ubifsls - list files in a directory
ubifsmount- mount UBIFS volume
ubifsumount- unmount UBIFS volume
usb - USB sub-system
usbboot - boot from USB device
version - print monitor, compiler and linker version
whoAmI - - reading CPU ID
Marvell>> printenv
CASset=min
MALLOC_len=5
autoload=no
baudrate=115200
bootargs=console=ttyS0,115200
bootargs_end=:10.4.50.254:255.255.255.0:KW40:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=nand read 0x2000000 0x2c00000 0x800000; bootm $loadaddr
bootcmd2=ide reset; ext4load ide 0:1 0x00800000 /boot/uImage; ext4load ide 0:1 0x2100000 /boot/uInitrd; setenv bootargs rootdelay=10 root=/dev/sda1 console=ttyS0,115200 earlyprintk0
bootdelay=3
cacheShare=no
console=console=ttyS0,115200
disL2Cache=yes
disaMvPnp=no
eeeEnable=no
enaAutoRecovery=yes
enaClockGating=no
enaFPU=no
enaWrAllo=no
eth1addr=00:50:43:02:00:00
eth1mtu=1500
ethact=egiga1
ethaddr=00:50:43:02:02:00
ethmtu=1500
ethprime=egiga1
image_name=uImage
initrd_name=uInitrd
ipaddr=192.168.1.200
loadaddr=0x02000000
loads_echo=0
mtdids=nand0=armada-nand
mtdparts=mtdparts=nand_mtd:4m(uboot),4m(uboot_env),4m(vendor),32m(rescue),8m(kernel),1024m(ubi),-(rootfs_data)
mvNetConfig=mv_net_config=1,(00:50:43:11:11:11,0:1:2:3:4),mtu=1500
mv_pon_addr=00:50:43:00:00:02
nandEcc=1bit
netbsd_en=no
netmask=255.255.255.0
netretry=no
pcieTune=no
pexMode=rc
pxe_files_load=:default.arm-armada370-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
rcvrip=169.254.100.100
rescueboot=nand read 0x2000000 0xc00000 0x2000000; bootm 0x2000000
rootpath=/srv/oneiric
sata_delay_reset=0
sata_dma_mode=yes
serverip=192.168.1.2
standalone=fsload 0x2000000 $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000;
stderr=serial
stdin=serial
stdout=serial
usb0Mode=host
usb1Mode=host
usb2Mode=device
usbActive=1
vxworks_en=no
Environment size: 1762/1048572 bytes
And the boot log:
Marvell>> run bootcmd2
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
Device 0 @ 0 0:
Model: JMicron Firm: 100415 Ser#: 00000000002E9
Type: Hard Disk
Supports 48-bit addressing
Capacity: 3836.0 MB = 3.7 GB (7856128 x 512)
Loading file "/boot/uImage" from ide device 0:1 hda1
5469032 bytes read
Loading file "/boot/uInitrd" from ide device 0:1 hda1
9518982 bytes read
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-5.9.3-mvebu-tld-1
Created: 1970-01-01 0:04:43 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5468968 Bytes = 5.2 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02100000 ...
Image Name: initramfs-5.9.3-mvebu-tld-1
Created: 1970-01-01 0:05:09 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 9518918 Bytes = 9.1 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 5.9.3-mvebu-tld-1 (root@tldDebianVM) (arm-linux-gnueabihf-gcc (Ubuntu/Linaro 7.5.0-3ubuntu1~18.04) 7.5.0, GNU ld (GNU Binutils for Ubuntu) 2.300
[ 0.000000][ T0] CPU: ARMv7 Processor [561f5811] revision 1 (ARMv7), cr=10c5387d
[ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: RTNAS V3
[ 0.000000][ T0] printk: bootconsole [earlycon0] enabled
[ 0.000000][ T0] Memory policy: Data cache writeback
[ 0.000000][ T0] Zone ranges:
[ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000002fffffff]
[ 0.000000][ T0] HighMem [mem 0x0000000030000000-0x000000003fffffff]
[ 0.000000][ T0] Movable zone start for each node
[ 0.000000][ T0] Early memory node ranges
[ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000003fffffff]
[ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
[ 0.000000][ T0] CPU: All CPU(s) started in SVC mode.
[ 0.000000][ T0] percpu: Embedded 20 pages/cpu s53068 r8192 d20660 u81920
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 260608
[ 0.000000][ T0] Kernel command line: rootdelay=10 root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial
[ 0.000000][ T0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[ 0.000000][ T0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000][ T0] Memory: 1013364K/1048576K available (10240K kernel code, 1047K rwdata, 3088K rodata, 1024K init, 341K bss, 35212K reserved, 0K cma-reserved, 262144K highmem)
[ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x304/0x75c with crng_init=0
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[ 0.000000][ T0] Trampoline variant of Tasks RCU enabled.
[ 0.000000][ T0] Rude variant of Tasks RCU enabled.
[ 0.000000][ T0] Tracing variant of Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] L2C: DT/platform modifies aux control register: 0x12086302 -> 0x1a086302
[ 0.000000][ T0] Aurora cache controller enabled, 4 ways, 256 kB
[ 0.000000][ T0] Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a086302
[ 0.000000][ T0] Switching to timer-based delay loop, resolution 53ns
[ 0.000007][ T0] sched_clock: 32 bits at 18MHz, resolution 53ns, wraps every 114840871909ns
[ 0.008588][ T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 102208375848 ns
[ 0.021016][ T0] Console: colour dummy device 80x30
[ 0.026163][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 37.39 BogoMIPS (lpj=186996)
[ 0.037202][ T0] pid_max: default: 32768 minimum: 301
[ 0.042739][ T0] LSM: Security Framework initializing
[ 0.048123][ T0] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.056118][ T0] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.065677][ T0] CPU: Testing write buffer coherency: ok
[ 0.071607][ T1] CPU0: thread -1, cpu 0, socket -1, mpidr 0
[ 0.078370][ T1] Setting up static identity map for 0x100000 - 0x100060
[ 0.085661][ T1] mvebu-soc-id: MVEBU SoC ID=0x6710, Rev=0x1
[ 0.091611][ T1] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.098687][ T1] rcu: Hierarchical SRCU implementation.
[ 0.105223][ T1] smp: Bringing up secondary CPUs ...
[ 0.110522][ T1] smp: Brought up 1 node, 1 CPU
[ 0.115207][ T1] SMP: Total of 1 processors activated (37.39 BogoMIPS).
[ 0.122095][ T1] CPU: All CPU(s) started in SVC mode.
[ 0.128096][ T1] devtmpfs: initialized
[ 0.136987][ T1] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6
[ 0.146826][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.157474][ T1] futex hash table entries: 256 (order: 2, 16384 bytes, linear)
[ 0.165336][ T1] xor: measuring software checksum speed
[ 0.270252][ T1] arm4regs : 1100.400 MB/sec
[ 0.370244][ T1] 8regs : 668.400 MB/sec
[ 0.470243][ T1] 32regs : 1064.000 MB/sec
[ 0.475101][ T1] xor: using function: arm4regs (1100.400 MB/sec)
[ 0.481385][ T1] prandom: seed boundary self test passed
[ 0.489570][ T1] prandom: 100 self tests passed
[ 0.494379][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.502518][ T1] NET: Registered protocol family 16
[ 0.508728][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.519185][ T1] audit: initializing netlink subsys (disabled)
[ 0.528583][ T1] thermal_sys: Registered thermal governor 'step_wise'
[ 0.528833][ T1] cpuidle: using governor ladder
[ 0.540421][ T30] audit: type=2000 audit(0.500:1): state=initialized audit_enabled=0 res=1
[ 0.553397][ T1] cpuidle: using governor menu
[ 0.558198][ T1] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.564973][ T1] mvebu-pmsu: CPU idle is currently broken: disabling
[ 0.901203][ T1] raid6: int32x8 gen() 213 MB/s
[ 1.070699][ T1] raid6: int32x8 xor() 135 MB/s
[ 1.240314][ T1] raid6: int32x4 gen() 223 MB/s
[ 1.410365][ T1] raid6: int32x4 xor() 150 MB/s
[ 1.580301][ T1] raid6: int32x2 gen() 413 MB/s
[ 1.750296][ T1] raid6: int32x2 xor() 216 MB/s
[ 1.920277][ T1] raid6: int32x1 gen() 429 MB/s
[ 2.090271][ T1] raid6: int32x1 xor() 200 MB/s
[ 2.095215][ T1] raid6: using algorithm int32x1 gen() 429 MB/s
[ 2.101334][ T1] raid6: .... xor() 200 MB/s, rmw enabled
[ 2.106883][ T1] raid6: using intx1 recovery algorithm
[ 2.113651][ T1] vgaarb: loaded
[ 2.120132][ T1] SCSI subsystem initialized
[ 2.126276][ T1] usbcore: registered new interface driver usbfs
[ 2.135400][ T1] usbcore: registered new interface driver hub
[ 2.142143][ T1] usbcore: registered new device driver usb
[ 2.149469][ T1] mc: Linux media interface: v0.10
[ 2.156555][ T1] videodev: Linux video capture interface: v2.00
[ 2.163785][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 2.169425][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 2.180965][ T1] PTP clock support registered
[ 2.190171][ T1] clocksource: Switched to clocksource armada_370_xp_clocksource
[ 3.219027][ T1] VFS: Disk quotas dquot_6.6.0
[ 3.223789][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 3.276216][ T1] NET: Registered protocol family 2
[ 3.283313][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 3.292811][ T1] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 3.301517][ T1] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 3.309396][ T1] TCP: Hash tables configured (established 8192 bind 8192)
[ 3.316863][ T1] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear)
[ 3.325145][ T1] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 3.332503][ T1] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 3.340473][ T1] NET: Registered protocol family 1
[ 3.346301][ T1] RPC: Registered named UNIX socket transport module.
[ 3.352986][ T1] RPC: Registered udp transport module.
[ 3.358362][ T1] RPC: Registered tcp transport module.
[ 3.363754][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 3.370880][ T1] PCI: CLS 0 bytes, default 64
[ 3.375842][ T1] Trying to unpack rootfs image as initramfs...
[ 3.988640][ T1] Freeing initrd memory: 9296K
[ 3.993564][ T1] NetWinder Floating Point Emulator V0.97 (double precision)
[ 4.001122][ T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
[ 4.013348][ T1] Initialise system trusted keyrings
[ 4.018516][ T1] Key type blacklist registered
[ 4.027418][ T1] workingset: timestamp_bits=30 max_order=18 bucket_order=0
[ 4.034811][ T1] zbud: loaded
[ 4.039710][ T1] NFS: Registering the id_resolver key type
[ 4.046139][ T1] Key type id_resolver registered
[ 4.051132][ T1] Key type id_legacy registered
[ 4.055871][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 4.063386][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 4.070793][ T1] jffs2: version 2.2. (NAND) (SUMMARY) �© 2001-2006 Red Hat, Inc.
[ 4.079798][ T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 4.087551][ T1] orangefs_init: module version upstream loaded
[ 4.165587][ T1] async_tx: api initialized (async)
[ 4.170705][ T1] Key type asymmetric registered
[ 4.175478][ T1] Asymmetric key parser 'x509' registered
[ 4.181490][ T1] bounce: pool size: 64 pages
[ 4.186226][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243)
[ 4.194818][ T1] io scheduler bfq registered
[ 4.202286][ T1] armada-370-pinctrl f1018000.pin-ctrl: registered pinctrl driver
[ 4.224681][ T1] mvebu-pcie soc:pcie@82000000: host bridge /soc/pcie@82000000 ranges:
[ 4.233574][ T1] mvebu-pcie soc:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000
[ 4.243179][ T1] mvebu-pcie soc:pcie@82000000: MEM 0x00f1080000..0x00f1081fff -> 0x0000080000
[ 4.252566][ T1] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 4.262345][ T1] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 4.272111][ T1] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0200000000
[ 4.281867][ T1] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0200000000
[ 4.292154][ T1] mvebu-pcie soc:pcie@82000000: PCI host bridge to bus 0000:00
[ 4.299531][ T1] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 4.306080][ T1] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff])
[ 4.317056][ T1] pci_bus 0000:00: root bus resource [mem 0xf1080000-0xf1081fff] (bus address [0x00080000-0x00081fff])
[ 4.327963][ T1] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff]
[ 4.335556][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 4.342723][ T1] pci 0000:00:01.0: [11ab:6710] type 01 class 0x060400
[ 4.349419][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[ 4.357672][ T1] pci 0000:00:02.0: [11ab:6710] type 01 class 0x060400
[ 4.365099][ T1] pci 0000:00:02.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[ 4.374321][ T1] PCI: bus0: Fast back to back transfers disabled
[ 4.381348][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 4.390031][ T1] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 4.399277][ T1] pci 0000:01:00.0: [168c:0030] type 00 class 0x028000
[ 4.406470][ T1] pci 0000:01:00.0: reg 0x10: [mem 0x40000000-0x4001ffff 64bit]
[ 4.414082][ T1] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 4.421633][ T1] pci 0000:01:00.0: supports D1 D2
[ 4.426580][ T1] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 4.434396][ T1] pci 0000:00:01.0: ASPM: current common clock configuration is inconsistent, reconfiguring
[ 4.471358][ T1] PCI: bus1: Fast back to back transfers enabled
[ 4.477531][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 4.485287][ T1] pci 0000:02:00.0: [168c:003c] type 00 class 0x028000
[ 4.492403][ T1] pci 0000:02:00.0: reg 0x10: [mem 0x42000000-0x421fffff 64bit]
[ 4.499899][ T1] pci 0000:02:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 4.507490][ T1] pci 0000:02:00.0: supports D1 D2
[ 4.512522][ T1] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 4.520344][ T1] pci 0000:00:02.0: ASPM: current common clock configuration is inconsistent, reconfiguring
[ 4.561351][ T1] PCI: bus2: Fast back to back transfers enabled
[ 4.567524][ T1] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 4.574960][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xf8000000-0xf80fffff]
[ 4.582561][ T1] pci 0000:00:02.0: BAR 14: assigned [mem 0xf8200000-0xf84fffff]
[ 4.590104][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xf8100000-0xf81007ff pref]
[ 4.598043][ T1] pci 0000:00:02.0: BAR 6: assigned [mem 0xf8500000-0xf85007ff pref]
[ 4.605957][ T1] pci 0000:01:00.0: BAR 0: assigned [mem 0xf8000000-0xf801ffff 64bit]
[ 4.613957][ T1] pci 0000:01:00.0: BAR 6: assigned [mem 0xf8020000-0xf802ffff pref]
[ 4.621859][ T1] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 4.627501][ T1] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xf80fffff]
[ 4.634978][ T1] pci 0000:02:00.0: BAR 0: assigned [mem 0xf8200000-0xf83fffff 64bit]
[ 4.642967][ T1] pci 0000:02:00.0: BAR 0: error updating (0xf8200004 != 0xffffffff)
[ 4.650866][ T1] pci 0000:02:00.0: BAR 0: error updating (high 0x000000 != 0xffffffff)
[ 4.659013][ T1] pci 0000:02:00.0: BAR 6: assigned [mem 0xf8400000-0xf840ffff pref]
[ 4.666912][ T1] pci 0000:00:02.0: PCI bridge to [bus 02]
[ 4.672567][ T1] pci 0000:00:02.0: bridge window [mem 0xf8200000-0xf84fffff]
[ 4.680177][ T1] pcieport 0000:00:01.0: enabling device (0140 -> 0142)
[ 4.687061][ T1] pcieport 0000:00:02.0: enabling device (0140 -> 0142)
[ 4.695216][ T1] mv_xor f1060800.xor: Marvell shared XOR driver
[ 4.761606][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 4.773496][ T1] mv_xor f1060900.xor: Marvell shared XOR driver
[ 4.841582][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 5.143001][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 5.155356][ T1] printk: console [ttyS0] disabled
[ 5.184420][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 18, base_baud = 12500000) is a 16550A
[ 5.194310][ T1] printk: console [ttyS0] enabled
[ 5.194310][ T1] printk: console [ttyS0] enabled
[ 5.204169][ T1] printk: bootconsole [earlycon0] disabled
[ 5.204169][ T1] printk: bootconsole [earlycon0] disabled
[ 5.218891][ T1] sata_mv f10a0000.sata: slots 32 ports 2
[ 5.233530][ T1] scsi host0: sata_mv
[ 5.239321][ T1] scsi host1: sata_mv
[ 5.244389][ T1] ata1: SATA max UDMA/133 irq 27
[ 5.249216][ T1] ata2: SATA max UDMA/133 irq 27
[ 5.256652][ T1] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x68
[ 5.265990][ T1] nand: Micron MT29F32G08CBACAWP
[ 5.271066][ T1] nand: 4096 MiB, MLC, erase size: 1024 KiB, page size: 4096, OOB size: 224
[ 5.279662][ T1] nand: WARNING: pxa3xx_nand-0: the ECC used on your system (16b/2048B) is too weak compared to the one required by the NAND chip (24b/1024B)
[ 5.296860][ T1] Bad block table found at page 1048320, version 0x01
[ 5.304975][ T1] Bad block table found at page 1048064, version 0x01
[ 5.312364][ T1] nand_read_bbt: bad block at 0x000005a00000
[ 5.318226][ T1] nand_read_bbt: bad block at 0x000005b00000
[ 5.324426][ T1] 7 fixed-partitions partitions found on MTD device pxa3xx_nand-0
[ 5.332186][ T1] Creating 7 MTD partitions on "pxa3xx_nand-0":
[ 5.338316][ T1] 0x000000000000-0x000000400000 : "u-boot"
[ 5.346349][ T1] 0x000000400000-0x000000800000 : "uboot_env"
[ 5.356151][ T1] 0x000000800000-0x000000c00000 : "vendor"
[ 5.365624][ T1] 0x000000c00000-0x000001800000 : "unused"
[ 5.375181][ T1] 0x000001800000-0x000001c00000 : "kernel"
[ 5.384823][ T1] 0x000001c00000-0x000040000000 : "ubi"
[ 5.394649][ T1] 0x000040000000-0x0000fbc00000 : "syscfg"
[ 5.406816][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 5.418541][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 5.432939][ T1] libphy: Fixed MDIO Bus: probed
[ 5.446800][ T1] libphy: orion_mdio_bus: probed
[ 5.466847][ T1] mvneta f1074000.ethernet eth0: Using device tree mac address 00:11:32:21:46:bf
[ 5.479865][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.489042][ T1] ehci-pci: EHCI PCI platform driver
[ 5.494890][ T1] ehci-orion: EHCI orion driver
[ 5.500459][ T1] orion-ehci f1050000.usb: EHCI Host Controller
[ 5.506669][ T1] orion-ehci f1050000.usb: new USB bus registered, assigned bus number 1
[ 5.515301][ T1] orion-ehci f1050000.usb: irq 24, io mem 0xf1050000
[ 5.550182][ T1] orion-ehci f1050000.usb: USB 2.0 started, EHCI 1.00
[ 5.557159][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.09
[ 5.566219][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.574217][ T1] usb usb1: Product: EHCI Host Controller
[ 5.579846][ T1] usb usb1: Manufacturer: Linux 5.9.3-mvebu-tld-1 ehci_hcd
[ 5.587027][ T1] usb usb1: SerialNumber: f1050000.usb
[ 5.593421][ T1] hub 1-0:1.0: USB hub found
[ 5.598653][ T1] hub 1-0:1.0: 1 port detected
[ 5.604483][ T1] orion-ehci f1051000.usb: EHCI Host Controller
[ 5.611721][ T1] orion-ehci f1051000.usb: new USB bus registered, assigned bus number 2
[ 5.620435][ T1] orion-ehci f1051000.usb: irq 25, io mem 0xf1051000
[ 5.650202][ T1] orion-ehci f1051000.usb: USB 2.0 started, EHCI 1.00
[ 5.657169][ T1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.09
[ 5.666239][ T1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.674218][ T1] usb usb2: Product: EHCI Host Controller
[ 5.679821][ T1] usb usb2: Manufacturer: Linux 5.9.3-mvebu-tld-1 ehci_hcd
[ 5.686922][ T1] usb usb2: SerialNumber: f1051000.usb
[ 5.693278][ T1] hub 2-0:1.0: USB hub found
[ 5.698498][ T1] hub 2-0:1.0: 1 port detected
[ 5.705108][ T1] usbcore: registered new interface driver usblp
[ 5.714432][ T1] usbcore: registered new interface driver usb-storage
[ 5.722482][ T1] mousedev: PS/2 mouse device common for all mice
[ 5.731627][ T1] i2c /dev entries driver
[ 5.750306][ T1218] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 5.759665][ T1218] ata1.00: ATA-7: JMicron, 100415, max UDMA/133
[ 5.767567][ T1] orion_wdt: Initial timeout 229 sec
[ 5.772931][ T1218] ata1.00: 7856128 sectors, multi 1: LBA48
[ 5.781587][ T1] device-mapper: uevent: version 1.0.3
[ 5.788524][ T1] device-mapper: ioctl: 4.42.0-ioctl (2020-02-27) initialised: dm-devel@redhat.com
[ 5.798022][ T1218] ata1.00: configured for UDMA/133
[ 5.804010][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 5.812293][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 5.820268][ T234] scsi 0:0:0:0: Direct-Access ATA JMicron 15 PQ: 0 ANSI: 5
[ 5.829234][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 5.838232][ T15] sd 0:0:0:0: [sda] 7856128 512-byte logical blocks: (4.02 GB/3.75 GiB)
[ 5.847429][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 5.855945][ T15] sd 0:0:0:0: [sda] Write Protect is off
[ 5.861569][ T1] device-mapper: raid: Loading target version 1.15.1
[ 5.868579][ T15] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 5.888587][ T15] sda: sda1 sda2
[ 5.894900][ T15] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.901839][ T1] marvell-cesa f1090000.crypto: CESA device successfully registered
[ 5.911463][ T1] hid: raw HID events driver (C) Jiri Kosina
[ 5.919573][ T1] usbcore: registered new interface driver usbhid
[ 5.927191][ T1] usbhid: USB HID core driver
[ 5.932719][ T1] drop_monitor: Initializing network drop monitor service
[ 5.941304][ T1] NET: Registered protocol family 10
[ 5.947904][ T1] Segment Routing with IPv6
[ 5.952471][ T1] RPL Segment Routing with IPv6
[ 5.957292][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 5.966375][ T1] NET: Registered protocol family 17
[ 5.973707][ T1] 8021q: 802.1Q VLAN Support v1.8
[ 5.978681][ T1] Key type dns_resolver registered
[ 5.983991][ T1] ThumbEE CPU extension supported.
[ 5.988994][ T1] Registering SWP/SWPB emulation handler
[ 5.995110][ T1] registered taskstats version 1
[ 5.999936][ T1] Loading compiled-in X.509 certificates
[ 6.006168][ T1] zswap: loaded using pool lzo/zbud
[ 6.011821][ T1] Key type ._fscrypt registered
[ 6.016556][ T1] Key type .fscrypt registered
[ 6.021332][ T1] Key type fscrypt-provisioning registered
[ 6.030579][ T1] Key type big_key registered
[ 6.062341][ T1] Key type encrypted registered
[ 6.071522][ T1] input: soc:internal-regs:gpio-keys as /devices/platform/soc/soc:internal-regs/soc:internal-regs:gpio-keys/input/input0
[ 6.180494][ T1223] ata2: SATA link down (SStatus 0 SControl F300)
[ 6.199015][ T1] Freeing unused kernel memory: 1024K
[ 6.206232][ T1] Checked W+X mappings: passed, no W+X pages found
[ 6.212659][ T1] Run /init as init process
Loading, please wait...
Starting version 241
[ 7.706838][ T1490] mv88e6085 f1072004.mdio-mii:00: switch 0x1710 detected: Marvell 88E6171, revision 2
[ 7.834834][ T1490] libphy: mdio: probed
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
[ 19.321955][ T1513] process '/usr/bin/fstype' started with executable stack
Begin: Will now check root file system ... fsck from util-linux 2.33.1
fsck: error 2 (No such file or directory) while executing fsck.ext4 for /dev/sda1
fsck exited with status code 8
done.
Warning: File system check failed but did not detect errors
[ 24.440706][ T1521] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
[ 24.638730][ C0] random: fast init done
INIT: version 2.93 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting hotplug events dispatcher: systemd-udevd. ok
[....] Synthesizing the initial hotplug events (subsystems)...done.
[....] Synthesizing the initial hotplug events (devices)...done.
[....] Waiting for /dev to be fully populated...[ 27.829621][ T1716] systemd-udevd[1716]: Using default interface naming scheme 'v240'.
[ 27.885385][ T1714] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 28.043270][ T1716] systemd-udevd[1716]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 28.430025][ T1728] systemd-udevd[1728]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 28.452761][ T1727] systemd-udevd[1727]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 28.468143][ T1715] systemd-udevd[1715]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 28.552584][ T1728] systemd-udevd[1728]: Could not generate persistent MAC address for ip6tnl0: No such file or directory
[ 28.616971][ T1712] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 28.766400][ T1712] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 28.847687][ T5] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 28.870337][ T5] cfg80211: failed to load regulatory.db
[ 29.328978][ T1712] ath9k 0000:01:00.0: enabling device (0000 -> 0002)
[ 29.436961][ T1726] ath10k_pci 0000:02:00.0: of_irq_parse_pci: failed with rc=134
[ 29.549559][ T1726] ath10k_pci 0000:02:00.0: can't change power state from D3hot to D0 (config space inaccessible)
[ 29.849230][ T1726] ath10k_pci 0000:02:00.0: failed to wake up device : -110
[ 29.915636][ T1726] ath10k_pci: probe of 0000:02:00.0 failed with error -110
[ 30.274118][ T1712] ieee80211 phy0: Atheros AR9300 Rev:3 mem=0xf0a40000, irq=58
[ 30.338463][ T5] mv88e6085 f1072004.mdio-mii:00: switch 0x1710 detected: Marvell 88E6171, revision 2
[ 30.377867][ T5] libphy: mdio: probed
[ 30.835692][ T5] mv88e6085 f1072004.mdio-mii:00 lan1 (uninitialized): PHY [!soc!internal-regs!mdio@72004!switch0@0!mdio:00] driver [Generic PHY] (irq=POLL)
[ 30.873225][ T5] mv88e6085 f1072004.mdio-mii:00 lan2 (uninitialized): PHY [!soc!internal-regs!mdio@72004!switch0@0!mdio:01] driver [Generic PHY] (irq=POLL)
[ 30.910522][ T5] mv88e6085 f1072004.mdio-mii:00 lan3 (uninitialized): PHY [!soc!internal-regs!mdio@72004!switch0@0!mdio:02] driver [Generic PHY] (irq=POLL)
[ 30.945932][ T5] mv88e6085 f1072004.mdio-mii:00 lan4 (uninitialized): PHY [!soc!internal-regs!mdio@72004!switch0@0!mdio:03] driver [Generic PHY] (irq=POLL)
[ 30.982069][ T5] mv88e6085 f1072004.mdio-mii:00 wan (uninitialized): PHY [!soc!internal-regs!mdio@72004!switch0@0!mdio:04] driver [Generic PHY] (irq=POLL)
[ 31.011852][ T5] mv88e6085 f1072004.mdio-mii:00: configuring for fixed/rgmii-id link mode
[ 31.030557][ T1507] mv88e6085 f1072004.mdio-mii:00: Link is Up - 1Gbps/Full - flow control off
[ 31.039281][ T5] DSA: tree 0 setup
[ 31.315289][ T1714] systemd-udevd[1714]: Using default interface naming scheme 'v240'.
[ 31.368330][ T1726] systemd-udevd[1726]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 31.413268][ T1729] systemd-udevd[1729]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 31.434224][ T1714] systemd-udevd[1714]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 31.541885][ T1714] ath9k 0000:01:00.0 wlp1s0: renamed from wlan0
done.
[....] Setting hostname to 'debian'...done.
[....] Activating swap:. ok
[ 33.978910][ T1971] EXT4-fs (sda1): re-mounted. Opts: (null)
[....] Will now check root file system:fsck from util-linux 2.33.1
[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sda1
e2fsck 1.44.5 (15-Dec-2018)
rootfs: clean, 45198/196608 files, 354173/786432 blocks
. ok
[ 34.239246][ T1997] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[info] Will now check all file systems.
fsck from util-linux 2.33.1
Checking all file systems.
LABEL=rootfs is mounted
[....] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.. ok
[....] Cleaning up temporary files.... ok
[info] Loading kernel module mv88e6xxx.
[....] Will now mount local filesystems:. ok
[....] Will now activate swapfile swap:done.
[....] Checking minimum space in /tmp...done.
[....] Cleaning up temporary files.... ok
[....] Starting Setting kernel variables: sysctl. ok
[....] Initializing random number generator...[ 36.984868][ T2466] random: dd: uninitialized urandom read (512 bytes read)
done.
[....] Configuring network interfaces...ifquery: unknown interface eth0
ifup: unknown interface eth0
failed.
[....] Starting RPC port mapper daemon: rpcbind. ok
[....] Starting NFS common utilities: statd idmapd. ok
[....] Cleaning up temporary files.... ok
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
2691 (syslogd)
. ok
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
2718 (klogd)
. ok
[....] Not starting NFS kernel daemon: no exports. ... (warning).
[....] Starting periodic command scheduler: cron. ok
[....] Starting system message bus: dbus[ 42.081760][ T2815] random: dbus-daemon: uninitialized urandom read (12 bytes read)
[ 42.145602][ T2815] random: dbus-daemon: uninitialized urandom read (12 bytes read)
. ok
[....] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon[ 42.503560][ T2838] random: avahi-daemon: uninitialized urandom read (4 bytes read)
. ok
[....] Starting NTP server: ntpd. ok
[....] Running local boot scripts (/etc/rc.local)Unsupported flash type 8 on /dev/mtd1
Unsupported flash type 8 on /dev/mtd1
[ 44.233934][ T2897] Setting Persistent MAC address to 00:50:43:02:02:00
<13>Dec 31 16:00:44 root[2904]: Setting Persistent MAC address to 00:50:43:02:02:00
ifdown: unknown interface eth0
ifup: unknown interface eth0
. ok
Debian GNU/Linux 10 debian ttyS0
debian login: root
Password:
Last login: Wed Dec 31 16:01:21 PST 1969 on ttyS0
Linux debian 5.9.3-mvebu-tld-1 #1.0 SMP PREEMPT Tue Nov 3 15:58:15 PST 2020 armv7l
The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
debian
RTNAS V3
Linux version 5.9.3-mvebu-tld-1 (root@tldDebianVM) (arm-linux-gnueabihf-gcc (Ubuntu/Linaro 7.5.0-3ubuntu1~18.04) 7.5.0, GNU ld (GNU Binutils for Ubuntu) 2.30) #1.0 SMP PREEMPT Tue 0
Debian 10.0
Wed Dec 31 16:00:52 PST 1969 up 0 minutes
root@debian:~#
|
Re: armada 370 (88f6710) mainline uboot support January 29, 2021 04:25PM |
Admin Registered: 13 years ago Posts: 18,548 |
wacke,
Cool! your DSA switch is looking great!
OK now your NAND is also recognized OK
Your bootargs does not have mtdparts, so the kernel is using one from the DTS.
Power up, interrupt serial console and
Your log was cutoff on the right side, so I could not see the whole bootcmd2 env.
We want to add $mtdparts to the bootargs in this bootcmd2. So reset your bootcmd2 with that variable right after earlyprintk=serial
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Quote
[ 30.835692][ T5] mv88e6085 f1072004.mdio-mii:00 lan1 (uninitialized): PHY [!soc!internal-regs!mdio@72004!switch0@0!mdio:00] driver [Generic PHY] (irq=POLL)
[ 30.873225][ T5] mv88e6085 f1072004.mdio-mii:00 lan2 (uninitialized): PHY [!soc!internal-regs!mdio@72004!switch0@0!mdio:01] driver [Generic PHY] (irq=POLL)
[ 30.910522][ T5] mv88e6085 f1072004.mdio-mii:00 lan3 (uninitialized): PHY [!soc!internal-regs!mdio@72004!switch0@0!mdio:02] driver [Generic PHY] (irq=POLL)
[ 30.945932][ T5] mv88e6085 f1072004.mdio-mii:00 lan4 (uninitialized): PHY [!soc!internal-regs!mdio@72004!switch0@0!mdio:03] driver [Generic PHY] (irq=POLL)
[ 30.982069][ T5] mv88e6085 f1072004.mdio-mii:00 wan (uninitialized): PHY [!soc!internal-regs!mdio@72004!switch0@0!mdio:04] driver [Generic PHY] (irq=POLL)
[ 31.011852][ T5] mv88e6085 f1072004.mdio-mii:00: configuring for fixed/rgmii-id link mode
[ 31.030557][ T1507] mv88e6085 f1072004.mdio-mii:00: Link is Up - 1Gbps/Full - flow control off
[ 31.039281][ T5] DSA: tree 0 setup
Cool! your DSA switch is looking great!
OK now your NAND is also recognized OK
[ 5.256652][ T1] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x68 [ 5.265990][ T1] nand: Micron MT29F32G08CBACAWP [ 5.271066][ T1] nand: 4096 MiB, MLC, erase size: 1024 KiB, page size: 4096, OOB size: 224 [ 5.279662][ T1] nand: WARNING: pxa3xx_nand-0: the ECC used on your system (16b/2048B) is too weak compared to the one required by the NAND chip (24b/1024B)
Your bootargs does not have mtdparts, so the kernel is using one from the DTS.
Power up, interrupt serial console and
setenv mtdparts 'mtdparts=pxa3xx_nand-0:4m(uboot),4m(uboot_env),4m(vendor),32m(rescue),8m(kernel),1024m(ubi),-(rootfs_data)'
Your log was cutoff on the right side, so I could not see the whole bootcmd2 env.
We want to add $mtdparts to the bootargs in this bootcmd2. So reset your bootcmd2 with that variable right after earlyprintk=serial
setenv bootcmd2 '.... earlyprintk=serial $mtdparts; .....'
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: armada 370 (88f6710) mainline uboot support January 29, 2021 07:08PM |
Registered: 8 years ago Posts: 166 |
Hi bodhi,
Tried, but no luck:
Tried, but no luck:
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12 (Jan 27 2021 - 10:27:11) RTNAS V3 2013_Q2.0
Board: RD-88F6710
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 200 [MHz]
DDR @ 600 [MHz]
DDR 16Bit Width, FastPath Memory Access
DRAM: 1 GiB
Port0: phyAddr=0x0, Not Marvell PHY id1 ffff id2 ffff
Map: Code: 0x3fef3000:0x3ff90674
BSS: 0x3ffef628
Stack: 0x3f9f2ef8
Heap: 0x3f9f3000:0x3fef3000
NAND: (ID 0x682c) 4096 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 1048320, version 0x01
Bad block table found at page 1048064, version 0x01
nand_read_bbt: Bad block at 0x000001680000
nand_read_bbt: Bad block at 0x0000016c0000
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 1.1
PEX 1: Root Complex Interface, Detected Link X1, GEN 1.1
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Modules/Interfaces Detected:
SDIO
RGMII1 Switch module
PEX0 (Lane 0)
PEX1 (Lane 1)
SATA0 (Lane 2)
SATA1 (Lane 3)
Net: egiga1 [PRIME]
Hit any key to stop autoboot: 0
Marvell>> <INTERRUPT>
Marvell>> setenv mtdparts 'mtdparts=pxa3xx_nand-0:4m(uboot),4m(uboot_env),4m(vendor),32m(rescue),8m(kernel),1024m(ubi),-(rootfs_data)'
Marvell>> setenv bootcmd2 'ide reset; ext4load ide 0:1 0x00800000 /boot/uImage; ext4load ide 0:1 0x2100000 /boot/uInitrd; setenv bootargs rootdelay=10 root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial $mtdparts; bootm 0x800000 0x2100000'
Marvell>> saveenv
Saving Environment to NAND...
Erasing Nand...
Writing to Nand... done
Marvell>> pri
CASset=min
MALLOC_len=5
autoload=no
baudrate=115200
bootargs=console=ttyS0,115200
bootargs_end=:10.4.50.254:255.255.255.0:KW40:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=nand read 0x2000000 0x2c00000 0x800000; bootm $loadaddr
bootcmd2=ide reset; ext4load ide 0:1 0x00800000 /boot/uImage; ext4load ide 0:1 0x2100000 /boot/uInitrd; setenv bootargs rootdelay=10 root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial $mtdparts; bootm 0x800000 0x2100000
bootdelay=3
cacheShare=no
console=console=ttyS0,115200
disL2Cache=yes
disaMvPnp=no
eeeEnable=no
enaAutoRecovery=yes
enaClockGating=no
enaFPU=no
enaWrAllo=no
eth1addr=00:50:43:02:00:00
eth1mtu=1500
ethact=egiga1
ethaddr=00:50:43:02:02:00
ethmtu=1500
ethprime=egiga1
image_name=uImage
initrd_name=uInitrd
ipaddr=192.168.1.200
loadaddr=0x02000000
loads_echo=0
mtdids=nand0=armada-nand
mtdparts=mtdparts=pxa3xx_nand-0:4m(uboot),4m(uboot_env),4m(vendor),32m(rescue),8m(kernel),1024m(ubi),-(rootfs_data)
mvNetConfig=mv_net_config=1,(00:50:43:11:11:11,0:1:2:3:4),mtu=1500
mv_pon_addr=00:50:43:00:00:02
nandEcc=1bit
netbsd_en=no
netmask=255.255.255.0
netretry=no
pcieTune=no
pexMode=rc
pxe_files_load=:default.arm-armada370-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
rcvrip=169.254.100.100
rescueboot=nand read 0x2000000 0xc00000 0x2000000; bootm 0x2000000
rootpath=/srv/oneiric
sata_delay_reset=0
sata_dma_mode=yes
serverip=192.168.1.2
standalone=fsload 0x2000000 $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000;
stderr=serial
stdin=serial
stdout=serial
usb0Mode=host
usb1Mode=host
usb2Mode=device
usbActive=1
vxworks_en=no
Environment size: 1777/1048572 bytes
Marvell>> run bootcmd2
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
Device 0 @ 0 0:
Model: JMicron Firm: 100415 Ser#: 00000000002E9
Type: Hard Disk
Supports 48-bit addressing
Capacity: 3836.0 MB = 3.7 GB (7856128 x 512)
Loading file "/boot/uImage" from ide device 0:1 hda1
5469032 bytes read
Loading file "/boot/uInitrd" from ide device 0:1 hda1
9518982 bytes read
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-5.9.3-mvebu-tld-1
Created: 1970-01-01 0:04:43 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5468968 Bytes = 5.2 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02100000 ...
Image Name: initramfs-5.9.3-mvebu-tld-1
Created: 1970-01-01 0:05:09 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 9518918 Bytes = 9.1 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 5.9.3-mvebu-tld-1 (root@tldDebianVM) (arm-linux-gnueabihf-gcc (Ubuntu/Linaro 7.5.0-3ubuntu1~18.04) 7.5.0, GNU ld (GNU Binutils for Ubuntu) 2.30) #1.0 SMP PREEMPT Tue Nov 3 15:58:15 PST 2020
[ 0.000000][ T0] CPU: ARMv7 Processor [561f5811] revision 1 (ARMv7), cr=10c5387d
[ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: RTNAS V3
[ 0.000000][ T0] printk: bootconsole [earlycon0] enabled
[ 0.000000][ T0] Memory policy: Data cache writeback
[ 0.000000][ T0] Zone ranges:
[ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000002fffffff]
[ 0.000000][ T0] HighMem [mem 0x0000000030000000-0x000000003fffffff]
[ 0.000000][ T0] Movable zone start for each node
[ 0.000000][ T0] Early memory node ranges
[ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000003fffffff]
[ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
[ 0.000000][ T0] CPU: All CPU(s) started in SVC mode.
[ 0.000000][ T0] percpu: Embedded 20 pages/cpu s53068 r8192 d20660 u81920
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 260608
[ 0.000000][ T0] Kernel command line: rootdelay=10 root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial mtdparts=pxa3xx_nand-0:4m(uboot),4m(uboot_env),4m(vendor),32m(rescue),8m(kernel),1024m(ubi),-(rootfs_data)
[ 0.000000][ T0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[ 0.000000][ T0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000][ T0] Memory: 1013364K/1048576K available (10240K kernel code, 1047K rwdata, 3088K rodata, 1024K init, 341K bss, 35212K reserved, 0K cma-reserved, 262144K highmem)
[ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x304/0x75c with crng_init=0
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[ 0.000000][ T0] Trampoline variant of Tasks RCU enabled.
[ 0.000000][ T0] Rude variant of Tasks RCU enabled.
[ 0.000000][ T0] Tracing variant of Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] L2C: DT/platform modifies aux control register: 0x12086302 -> 0x1a086302
[ 0.000000][ T0] Aurora cache controller enabled, 4 ways, 256 kB
[ 0.000000][ T0] Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a086302
[ 0.000000][ T0] Switching to timer-based delay loop, resolution 53ns
[ 0.000006][ T0] sched_clock: 32 bits at 18MHz, resolution 53ns, wraps every 114840871909ns
[ 0.008587][ T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 102208375848 ns
[ 0.021014][ T0] Console: colour dummy device 80x30
[ 0.026162][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 37.39 BogoMIPS (lpj=186996)
[ 0.037201][ T0] pid_max: default: 32768 minimum: 301
[ 0.042739][ T0] LSM: Security Framework initializing
[ 0.048124][ T0] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.056118][ T0] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.065681][ T0] CPU: Testing write buffer coherency: ok
[ 0.071611][ T1] CPU0: thread -1, cpu 0, socket -1, mpidr 0
[ 0.078368][ T1] Setting up static identity map for 0x100000 - 0x100060
[ 0.085659][ T1] mvebu-soc-id: MVEBU SoC ID=0x6710, Rev=0x1
[ 0.091608][ T1] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.098685][ T1] rcu: Hierarchical SRCU implementation.
[ 0.105230][ T1] smp: Bringing up secondary CPUs ...
[ 0.110525][ T1] smp: Brought up 1 node, 1 CPU
[ 0.115211][ T1] SMP: Total of 1 processors activated (37.39 BogoMIPS).
[ 0.122099][ T1] CPU: All CPU(s) started in SVC mode.
[ 0.128103][ T1] devtmpfs: initialized
[ 0.137073][ T1] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6
[ 0.146912][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.157559][ T1] futex hash table entries: 256 (order: 2, 16384 bytes, linear)
[ 0.165417][ T1] xor: measuring software checksum speed
[ 0.270252][ T1] arm4regs : 1100.400 MB/sec
[ 0.370243][ T1] 8regs : 668.800 MB/sec
[ 0.470247][ T1] 32regs : 1064.000 MB/sec
[ 0.475105][ T1] xor: using function: arm4regs (1100.400 MB/sec)
[ 0.481389][ T1] prandom: seed boundary self test passed
[ 0.489574][ T1] prandom: 100 self tests passed
[ 0.494383][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.502508][ T1] NET: Registered protocol family 16
[ 0.508752][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.519214][ T1] audit: initializing netlink subsys (disabled)
[ 0.528600][ T1] thermal_sys: Registered thermal governor 'step_wise'
[ 0.528850][ T1] cpuidle: using governor ladder
[ 0.540439][ T30] audit: type=2000 audit(0.500:1): state=initialized audit_enabled=0 res=1
[ 0.553405][ T1] cpuidle: using governor menu
[ 0.558244][ T1] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.565019][ T1] mvebu-pmsu: CPU idle is currently broken: disabling
[ 0.901231][ T1] raid6: int32x8 gen() 213 MB/s
[ 1.070654][ T1] raid6: int32x8 xor() 135 MB/s
[ 1.240323][ T1] raid6: int32x4 gen() 223 MB/s
[ 1.410331][ T1] raid6: int32x4 xor() 150 MB/s
[ 1.580299][ T1] raid6: int32x2 gen() 413 MB/s
[ 1.750286][ T1] raid6: int32x2 xor() 216 MB/s
[ 1.920270][ T1] raid6: int32x1 gen() 429 MB/s
[ 2.090267][ T1] raid6: int32x1 xor() 200 MB/s
[ 2.095210][ T1] raid6: using algorithm int32x1 gen() 429 MB/s
[ 2.101329][ T1] raid6: .... xor() 200 MB/s, rmw enabled
[ 2.106877][ T1] raid6: using intx1 recovery algorithm
[ 2.113634][ T1] vgaarb: loaded
[ 2.120121][ T1] SCSI subsystem initialized
[ 2.126235][ T1] usbcore: registered new interface driver usbfs
[ 2.135362][ T1] usbcore: registered new interface driver hub
[ 2.142110][ T1] usbcore: registered new device driver usb
[ 2.149419][ T1] mc: Linux media interface: v0.10
[ 2.156502][ T1] videodev: Linux video capture interface: v2.00
[ 2.163732][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 2.169372][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 2.180899][ T1] PTP clock support registered
[ 2.190145][ T1] clocksource: Switched to clocksource armada_370_xp_clocksource
[ 3.218797][ T1] VFS: Disk quotas dquot_6.6.0
[ 3.223557][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 3.274161][ T1] NET: Registered protocol family 2
[ 3.281908][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 3.291301][ T1] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 3.299850][ T1] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 3.307877][ T1] TCP: Hash tables configured (established 8192 bind 8192)
[ 3.315366][ T1] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear)
[ 3.323586][ T1] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 3.330993][ T1] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 3.338935][ T1] NET: Registered protocol family 1
[ 3.344799][ T1] RPC: Registered named UNIX socket transport module.
[ 3.351481][ T1] RPC: Registered udp transport module.
[ 3.356857][ T1] RPC: Registered tcp transport module.
[ 3.362249][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 3.369359][ T1] PCI: CLS 0 bytes, default 64
[ 3.374326][ T1] Trying to unpack rootfs image as initramfs...
[ 3.987167][ T1] Freeing initrd memory: 9296K
[ 3.992114][ T1] NetWinder Floating Point Emulator V0.97 (double precision)
[ 3.999608][ T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
[ 4.011921][ T1] Initialise system trusted keyrings
[ 4.017089][ T1] Key type blacklist registered
[ 4.026020][ T1] workingset: timestamp_bits=30 max_order=18 bucket_order=0
[ 4.033470][ T1] zbud: loaded
[ 4.038367][ T1] NFS: Registering the id_resolver key type
[ 4.044777][ T1] Key type id_resolver registered
[ 4.049640][ T1] Key type id_legacy registered
[ 4.054553][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 4.062057][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 4.069394][ T1] jffs2: version 2.2. (NAND) (SUMMARY) �© 2001-2006 Red Hat, Inc.
[ 4.078498][ T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 4.086246][ T1] orangefs_init: module version upstream loaded
[ 4.167277][ T1] async_tx: api initialized (async)
[ 4.172397][ T1] Key type asymmetric registered
[ 4.177169][ T1] Asymmetric key parser 'x509' registered
[ 4.183187][ T1] bounce: pool size: 64 pages
[ 4.187925][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243)
[ 4.196527][ T1] io scheduler bfq registered
[ 4.203925][ T1] armada-370-pinctrl f1018000.pin-ctrl: registered pinctrl driver
[ 4.224768][ T1] mvebu-pcie soc:pcie@82000000: host bridge /soc/pcie@82000000 ranges:
[ 4.235205][ T1] mvebu-pcie soc:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000
[ 4.244778][ T1] mvebu-pcie soc:pcie@82000000: MEM 0x00f1080000..0x00f1081fff -> 0x0000080000
[ 4.254205][ T1] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 4.263993][ T1] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 4.273761][ T1] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0200000000
[ 4.283525][ T1] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0200000000
[ 4.293814][ T1] mvebu-pcie soc:pcie@82000000: PCI host bridge to bus 0000:00
[ 4.301581][ T1] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 4.307744][ T1] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff])
[ 4.318712][ T1] pci_bus 0000:00: root bus resource [mem 0xf1080000-0xf1081fff] (bus address [0x00080000-0x00081fff])
[ 4.329620][ T1] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff]
[ 4.337213][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 4.344382][ T1] pci 0000:00:01.0: [11ab:6710] type 01 class 0x060400
[ 4.351150][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[ 4.359336][ T1] pci 0000:00:02.0: [11ab:6710] type 01 class 0x060400
[ 4.366771][ T1] pci 0000:00:02.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[ 4.376001][ T1] PCI: bus0: Fast back to back transfers disabled
[ 4.383014][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 4.391847][ T1] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 4.401041][ T1] pci 0000:01:00.0: [168c:0030] type 00 class 0x028000
[ 4.407744][ T1] pci 0000:01:00.0: reg 0x10: [mem 0x40000000-0x4001ffff 64bit]
[ 4.415647][ T1] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 4.423235][ T1] pci 0000:01:00.0: supports D1 D2
[ 4.428182][ T1] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 4.436047][ T1] pci 0000:00:01.0: ASPM: current common clock configuration is inconsistent, reconfiguring
[ 4.501296][ T1] PCI: bus1: Fast back to back transfers enabled
[ 4.507467][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 4.515179][ T1] pci 0000:02:00.0: [168c:003c] type 00 class 0x028000
[ 4.522248][ T1] pci 0000:02:00.0: reg 0x10: [mem 0x42000000-0x421fffff 64bit]
[ 4.529743][ T1] pci 0000:02:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 4.537330][ T1] pci 0000:02:00.0: supports D1 D2
[ 4.542366][ T1] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 4.550204][ T1] pci 0000:00:02.0: ASPM: current common clock configuration is inconsistent, reconfiguring
[ 4.611298][ T1] PCI: bus2: Fast back to back transfers enabled
[ 4.617471][ T1] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 4.624896][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xf8000000-0xf80fffff]
[ 4.632467][ T1] pci 0000:00:02.0: BAR 14: assigned [mem 0xf8200000-0xf84fffff]
[ 4.640009][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xf8100000-0xf81007ff pref]
[ 4.647914][ T1] pci 0000:00:02.0: BAR 6: assigned [mem 0xf8500000-0xf85007ff pref]
[ 4.655821][ T1] pci 0000:01:00.0: BAR 0: assigned [mem 0xf8000000-0xf801ffff 64bit]
[ 4.663819][ T1] pci 0000:01:00.0: BAR 6: assigned [mem 0xf8020000-0xf802ffff pref]
[ 4.671719][ T1] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 4.677361][ T1] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xf80fffff]
[ 4.684837][ T1] pci 0000:02:00.0: BAR 0: assigned [mem 0xf8200000-0xf83fffff 64bit]
[ 4.692826][ T1] pci 0000:02:00.0: BAR 0: error updating (0xf8200004 != 0xffffffff)
[ 4.700725][ T1] pci 0000:02:00.0: BAR 0: error updating (high 0x000000 != 0xffffffff)
[ 4.708872][ T1] pci 0000:02:00.0: BAR 6: assigned [mem 0xf8400000-0xf840ffff pref]
[ 4.716771][ T1] pci 0000:00:02.0: PCI bridge to [bus 02]
[ 4.722425][ T1] pci 0000:00:02.0: bridge window [mem 0xf8200000-0xf84fffff]
[ 4.730006][ T1] pcieport 0000:00:01.0: enabling device (0140 -> 0142)
[ 4.736917][ T1] pcieport 0000:00:02.0: enabling device (0140 -> 0142)
[ 4.745060][ T1] mv_xor f1060800.xor: Marvell shared XOR driver
[ 4.811579][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 4.823438][ T1] mv_xor f1060900.xor: Marvell shared XOR driver
[ 4.891583][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 5.190003][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 5.203547][ T1] printk: console [ttyS0] disabled
[ 5.232735][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 18, base_baud = 12500000) is a 16550A
[ 5.242607][ T1] printk: console [ttyS0] enabled
[ 5.242607][ T1] printk: console [ttyS0] enabled
[ 5.252615][ T1] printk: bootconsole [earlycon0] disabled
[ 5.252615][ T1] printk: bootconsole [earlycon0] disabled
[ 5.267292][ T1] sata_mv f10a0000.sata: slots 32 ports 2
[ 5.282011][ T1] scsi host0: sata_mv
[ 5.287811][ T1] scsi host1: sata_mv
[ 5.292862][ T1] ata1: SATA max UDMA/133 irq 27
[ 5.297688][ T1] ata2: SATA max UDMA/133 irq 27
[ 5.305134][ T1] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x68
[ 5.314445][ T1] nand: Micron MT29F32G08CBACAWP
[ 5.319273][ T1] nand: 4096 MiB, MLC, erase size: 1024 KiB, page size: 4096, OOB size: 224
[ 5.328112][ T1] nand: WARNING: pxa3xx_nand-0: the ECC used on your system (16b/2048B) is too weak compared to the one required by the NAND chip (24b/1024B)
[ 5.345347][ T1] Bad block table found at page 1048320, version 0x01
[ 5.353457][ T1] Bad block table found at page 1048064, version 0x01
[ 5.360796][ T1] nand_read_bbt: bad block at 0x000005a00000
[ 5.366658][ T1] nand_read_bbt: bad block at 0x000005b00000
[ 5.372830][ T1] 7 cmdlinepart partitions found on MTD device pxa3xx_nand-0
[ 5.380090][ T1] Creating 7 MTD partitions on "pxa3xx_nand-0":
[ 5.386246][ T1] 0x000000000000-0x000000400000 : "uboot"
[ 5.394116][ T1] 0x000000400000-0x000000800000 : "uboot_env"
[ 5.403797][ T1] 0x000000800000-0x000000c00000 : "vendor"
[ 5.413235][ T1] 0x000000c00000-0x000002c00000 : "rescue"
[ 5.422709][ T1] 0x000002c00000-0x000003400000 : "kernel"
[ 5.432261][ T1] 0x000003400000-0x000043400000 : "ubi"
[ 5.441997][ T1] 0x000043400000-0x000100000000 : "rootfs_data"
[ 5.454532][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 5.466119][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 5.480653][ T1] libphy: Fixed MDIO Bus: probed
[ 5.494466][ T1] libphy: orion_mdio_bus: probed
[ 5.515084][ T1] mvneta f1074000.ethernet eth0: Using device tree mac address 00:11:32:21:46:bf
[ 5.527106][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.536375][ T1] ehci-pci: EHCI PCI platform driver
[ 5.542088][ T1] ehci-orion: EHCI orion driver
[ 5.547393][ T1] orion-ehci f1050000.usb: EHCI Host Controller
[ 5.553829][ T1] orion-ehci f1050000.usb: new USB bus registered, assigned bus number 1
[ 5.562457][ T1] orion-ehci f1050000.usb: irq 24, io mem 0xf1050000
[ 5.590174][ T1] orion-ehci f1050000.usb: USB 2.0 started, EHCI 1.00
[ 5.597143][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.09
[ 5.606204][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.614200][ T1] usb usb1: Product: EHCI Host Controller
[ 5.619828][ T1] usb usb1: Manufacturer: Linux 5.9.3-mvebu-tld-1 ehci_hcd
[ 5.626950][ T1] usb usb1: SerialNumber: f1050000.usb
[ 5.633401][ T1] hub 1-0:1.0: USB hub found
[ 5.638634][ T1] hub 1-0:1.0: 1 port detected
[ 5.644488][ T1] orion-ehci f1051000.usb: EHCI Host Controller
[ 5.651724][ T1] orion-ehci f1051000.usb: new USB bus registered, assigned bus number 2
[ 5.660441][ T1] orion-ehci f1051000.usb: irq 25, io mem 0xf1051000
[ 5.690176][ T1] orion-ehci f1051000.usb: USB 2.0 started, EHCI 1.00
[ 5.697139][ T1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.09
[ 5.706209][ T1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.714188][ T1] usb usb2: Product: EHCI Host Controller
[ 5.719790][ T1] usb usb2: Manufacturer: Linux 5.9.3-mvebu-tld-1 ehci_hcd
[ 5.726890][ T1] usb usb2: SerialNumber: f1051000.usb
[ 5.733241][ T1] hub 2-0:1.0: USB hub found
[ 5.738456][ T1] hub 2-0:1.0: 1 port detected
[ 5.745074][ T1] usbcore: registered new interface driver usblp
[ 5.754560][ T1] usbcore: registered new interface driver usb-storage
[ 5.762592][ T1] mousedev: PS/2 mouse device common for all mice
[ 5.771763][ T1] i2c /dev entries driver
[ 5.800216][ T1218] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 5.809234][ T1] orion_wdt: Initial timeout 229 sec
[ 5.816283][ T1218] ata1.00: ATA-7: JMicron, 100415, max UDMA/133
[ 5.823456][ T1] device-mapper: uevent: version 1.0.3
[ 5.829730][ T1218] ata1.00: 7856128 sectors, multi 1: LBA48
[ 5.836142][ T1] device-mapper: ioctl: 4.42.0-ioctl (2020-02-27) initialised: dm-devel@redhat.com
[ 5.846700][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 5.854280][ T1218] ata1.00: configured for UDMA/133
[ 5.860332][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 5.867683][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 5.875621][ T15] scsi 0:0:0:0: Direct-Access ATA JMicron 15 PQ: 0 ANSI: 5
[ 5.884604][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 5.893173][ T1228] sd 0:0:0:0: [sda] 7856128 512-byte logical blocks: (4.02 GB/3.75 GiB)
[ 5.901845][ T1] device-mapper: raid: Loading target version 1.15.1
[ 5.914576][ T1228] sd 0:0:0:0: [sda] Write Protect is off
[ 5.921154][ T1228] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 5.935745][ T1] marvell-cesa f1090000.crypto: CESA device successfully registered
[ 5.944943][ T1228] sda: sda1 sda2
[ 5.949409][ T1] hid: raw HID events driver (C) Jiri Kosina
[ 5.958191][ T1228] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.966298][ T1] usbcore: registered new interface driver usbhid
[ 5.974296][ T1] usbhid: USB HID core driver
[ 5.979916][ T1] drop_monitor: Initializing network drop monitor service
[ 5.988313][ T1] NET: Registered protocol family 10
[ 5.995109][ T1] Segment Routing with IPv6
[ 5.999497][ T1] RPL Segment Routing with IPv6
[ 6.004491][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 6.013574][ T1] NET: Registered protocol family 17
[ 6.020861][ T1] 8021q: 802.1Q VLAN Support v1.8
[ 6.025843][ T1] Key type dns_resolver registered
[ 6.031228][ T1] ThumbEE CPU extension supported.
[ 6.036230][ T1] Registering SWP/SWPB emulation handler
[ 6.042427][ T1] registered taskstats version 1
[ 6.047253][ T1] Loading compiled-in X.509 certificates
[ 6.053365][ T1] zswap: loaded using pool lzo/zbud
[ 6.058928][ T1] Key type ._fscrypt registered
[ 6.063782][ T1] Key type .fscrypt registered
[ 6.068426][ T1] Key type fscrypt-provisioning registered
[ 6.077597][ T1] Key type big_key registered
[ 6.109506][ T1] Key type encrypted registered
[ 6.118640][ T1] input: soc:internal-regs:gpio-keys as /devices/platform/soc/soc:internal-regs/soc:internal-regs:gpio-keys/input/input0
[ 6.242863][ T1223] ata2: SATA link down (SStatus 0 SControl F300)
[ 6.261414][ T1] Freeing unused kernel memory: 1024K
[ 6.268598][ T1] Checked W+X mappings: passed, no W+X pages found
[ 6.275034][ T1] Run /init as init process
Loading, please wait...
Starting version 241
[ 7.799132][ T1487] mv88e6085 f1072004.mdio-mii:00: switch 0x1710 detected: Marvell 88E6171, revision 2
[ 7.935209][ T1487] libphy: mdio: probed
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
[ 19.431956][ T1513] process '/usr/bin/fstype' started with executable stack
Begin: Will now check root file system ... fsck from util-linux 2.33.1
fsck: error 2 (No such file or directory) while executing fsck.ext4 for /dev/sda1
fsck exited with status code 8
done.
Warning: File system check failed but did not detect errors
[ 24.550675][ T1521] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
[ 24.748177][ C0] random: fast init done
INIT: version 2.93 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting hotplug events dispatcher: systemd-udevd. ok
[....] Synthesizing the initial hotplug events (subsystems)...done.
[....] Synthesizing the initial hotplug events (devices)...done.
[....] Waiting for /dev to be fully populated...[ 27.904437][ T1716] systemd-udevd[1716]: Using default interface naming scheme 'v240'.
[ 28.010088][ T1721] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 28.084100][ T1716] systemd-udevd[1716]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 28.557614][ T1721] systemd-udevd[1721]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 28.572215][ T1722] systemd-udevd[1722]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 28.603207][ T1715] systemd-udevd[1715]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 28.698993][ T1714] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 28.712302][ T1722] systemd-udevd[1722]: Could not generate persistent MAC address for ip6tnl0: No such file or directory
[ 28.842551][ T1714] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 28.850035][ T1507] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 28.859507][ T1507] cfg80211: failed to load regulatory.db
[ 29.396042][ T1714] ath9k 0000:01:00.0: enabling device (0000 -> 0002)
[ 29.464347][ T1725] ath10k_pci 0000:02:00.0: of_irq_parse_pci: failed with rc=134
[ 29.611094][ T1725] ath10k_pci 0000:02:00.0: can't change power state from D3hot to D0 (config space inaccessible)
[ 29.934949][ T1725] ath10k_pci 0000:02:00.0: failed to wake up device : -110
[ 29.978596][ T1725] ath10k_pci: probe of 0000:02:00.0 failed with error -110
[ 30.375266][ T1714] ieee80211 phy0: Atheros AR9300 Rev:3 mem=0xf0a00000, irq=58
[ 30.440578][ T1507] mv88e6085 f1072004.mdio-mii:00: switch 0x1710 detected: Marvell 88E6171, revision 2
[ 30.481479][ T1507] libphy: mdio: probed
[ 30.932981][ T1507] mv88e6085 f1072004.mdio-mii:00 lan1 (uninitialized): PHY [!soc!internal-regs!mdio@72004!switch0@0!mdio:00] driver [Generic PHY] (irq=POLL)
[ 30.970473][ T1507] mv88e6085 f1072004.mdio-mii:00 lan2 (uninitialized): PHY [!soc!internal-regs!mdio@72004!switch0@0!mdio:01] driver [Generic PHY] (irq=POLL)
[ 31.008025][ T1507] mv88e6085 f1072004.mdio-mii:00 lan3 (uninitialized): PHY [!soc!internal-regs!mdio@72004!switch0@0!mdio:02] driver [Generic PHY] (irq=POLL)
[ 31.043391][ T1507] mv88e6085 f1072004.mdio-mii:00 lan4 (uninitialized): PHY [!soc!internal-regs!mdio@72004!switch0@0!mdio:03] driver [Generic PHY] (irq=POLL)
[ 31.080515][ T1507] mv88e6085 f1072004.mdio-mii:00 wan (uninitialized): PHY [!soc!internal-regs!mdio@72004!switch0@0!mdio:04] driver [Generic PHY] (irq=POLL)
[ 31.110721][ T1507] mv88e6085 f1072004.mdio-mii:00: configuring for fixed/rgmii-id link mode
[ 31.129109][ T1507] DSA: tree 0 setup
[ 31.133401][ T20] mv88e6085 f1072004.mdio-mii:00: Link is Up - 1Gbps/Full - flow control off
[ 31.457351][ T1713] systemd-udevd[1713]: Using default interface naming scheme 'v240'.
[ 31.542942][ T1725] systemd-udevd[1725]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 31.575391][ T1713] systemd-udevd[1713]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 31.616403][ T1714] systemd-udevd[1714]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 31.698748][ T1713] ath9k 0000:01:00.0 wlp1s0: renamed from wlan0
done.
[....] Setting hostname to 'debian'...done.
[....] Activating swap:. ok
[ 34.145373][ T1970] EXT4-fs (sda1): re-mounted. Opts: (null)
[....] Will now check root file system:fsck from util-linux 2.33.1
[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sda1
e2fsck 1.44.5 (15-Dec-2018)
rootfs: clean, 45198/196608 files, 354175/786432 blocks
. ok
[ 34.404122][ T1996] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[info] Will now check all file systems.
fsck from util-linux 2.33.1
Checking all file systems.
LABEL=rootfs is mounted
[....] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.. ok
[....] Cleaning up temporary files.... ok
[info] Loading kernel module mv88e6xxx.
[....] Will now mount local filesystems:. ok
[....] Will now activate swapfile swap:done.
[....] Checking minimum space in /tmp...done.
[....] Cleaning up temporary files.... ok
[....] Starting Setting kernel variables: sysctl. ok
[....] Initializing random number generator...[ 37.162098][ T2465] random: dd: uninitialized urandom read (512 bytes read)
done.
[....] Configuring network interfaces...ifquery: unknown interface eth0
ifup: unknown interface eth0
failed.
[....] Starting RPC port mapper daemon: rpcbind. ok
[....] Starting NFS common utilities: statd idmapd. ok
[....] Cleaning up temporary files.... ok
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
2690 (syslogd)
. ok
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
2717 (klogd)
. ok
[....] Not starting NFS kernel daemon: no exports. ... (warning).
[....] Starting periodic command scheduler: cron. ok
[....] Starting system message bus: dbus[ 42.261740][ T2814] random: dbus-daemon: uninitialized urandom read (12 bytes read)
[ 42.325574][ T2814] random: dbus-daemon: uninitialized urandom read (12 bytes read)
. ok
[....] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon[ 42.683632][ T2837] random: avahi-daemon: uninitialized urandom read (4 bytes read)
. ok
[....] Starting NTP server: ntpd. ok
[....] Running local boot scripts (/etc/rc.local)Unsupported flash type 8 on /dev/mtd1
Unsupported flash type 8 on /dev/mtd1
[ 44.403834][ T2896] Setting Persistent MAC address to 00:50:43:02:02:00
<13>Dec 31 16:00:44 root[2903]: Setting Persistent MAC address to 00:50:43:02:02:00
ifdown: unknown interface eth0
ifup: unknown interface eth0
. ok
Debian GNU/Linux 10 debian ttyS0
debian login: root
Password:
Last login: Wed Dec 31 16:00:51 PST 1969 on ttyS0
Linux debian 5.9.3-mvebu-tld-1 #1.0 SMP PREEMPT Tue Nov 3 15:58:15 PST 2020 armv7l
The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
debian
RTNAS V3
Linux version 5.9.3-mvebu-tld-1 (root@tldDebianVM) (arm-linux-gnueabihf-gcc (Ubuntu/Linaro 7.5.0-3ubuntu1~18.04) 7.5.0, GNU ld (GNU Binutils for Ubuntu) 2.30) #1.0 SMP PREEMPT Tue Nov 3 15:58:15 PST 2020
Debian 10.0
Wed Dec 31 16:00:52 PST 1969 up 0 minutes
root@debian:~# fw_printenv
Unsupported flash type 8 on /dev/mtd1
CASset=min
MALLOC_len=5
autoload=no
baudrate=115200
bootargs=console=ttyS0,115200
bootargs_end=:10.4.50.254:255.255.255.0:KW40:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=nand read 0x2000000 0x2c00000 0x800000; bootm $loadaddr
bootcmd2=ide reset; ext4load ide 0:1 0x00800000 /boot/uImage; ext4load ide 0:1 0x2100000 /boot/uInitrd; setenv bootargs rootdelay=10 root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial $mtdparts; bootm 0x800000 0x2100000
bootdelay=3
cacheShare=no
console=console=ttyS0,115200
disL2Cache=yes
disaMvPnp=no
eeeEnable=no
enaAutoRecovery=yes
enaClockGating=no
enaFPU=no
enaWrAllo=no
eth1addr=00:50:43:02:00:00
eth1mtu=1500
ethact=egiga1
ethaddr=00:50:43:02:02:00
ethmtu=1500
ethprime=egiga1
image_name=uImage
initrd_name=uInitrd
ipaddr=192.168.1.200
loadaddr=0x02000000
loads_echo=0
mtdids=nand0=armada-nand
mtdparts=mtdparts=pxa3xx_nand-0:4m(uboot),4m(uboot_env),4m(vendor),32m(rescue),8m(kernel),1024m(ubi),-(rootfs_data)
mvNetConfig=mv_net_config=1,(00:50:43:11:11:11,0:1:2:3:4),mtu=1500
mv_pon_addr=00:50:43:00:00:02
nandEcc=1bit
netbsd_en=no
netmask=255.255.255.0
netretry=no
pcieTune=no
pexMode=rc
pxe_files_load=:default.arm-armada370-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
rcvrip=169.254.100.100
rescueboot=nand read 0x2000000 0xc00000 0x2000000; bootm 0x2000000
rootpath=/srv/oneiric
sata_delay_reset=0
sata_dma_mode=yes
serverip=192.168.1.2
standalone=fsload 0x2000000 $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000;
stderr=serial
stdin=serial
stdout=serial
usb0Mode=host
usb1Mode=host
usb2Mode=device
usbActive=1
vxworks_en=no
|
Re: armada 370 (88f6710) mainline uboot support January 29, 2021 09:23PM |
Admin Registered: 13 years ago Posts: 18,548 |
[ 5.305134][ T1] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x68 [ 5.314445][ T1] nand: Micron MT29F32G08CBACAWP [ 5.319273][ T1] nand: 4096 MiB, MLC, erase size: 1024 KiB, page size: 4096, OOB size: 224 [ 5.328112][ T1] nand: WARNING: pxa3xx_nand-0: the ECC used on your system (16b/2048B) is too weak compared to the one required by the NAND chip (24b/1024B) [ 5.345347][ T1] Bad block table found at page 1048320, version 0x01 [ 5.353457][ T1] Bad block table found at page 1048064, version 0x01 [ 5.360796][ T1] nand_read_bbt: bad block at 0x000005a00000 [ 5.366658][ T1] nand_read_bbt: bad block at 0x000005b00000 [ 5.372830][ T1] 7 cmdlinepart partitions found on MTD device pxa3xx_nand-0 [ 5.380090][ T1] Creating 7 MTD partitions on "pxa3xx_nand-0": [ 5.386246][ T1] 0x000000000000-0x000000400000 : "uboot" [ 5.394116][ T1] 0x000000400000-0x000000800000 : "uboot_env" [ 5.403797][ T1] 0x000000800000-0x000000c00000 : "vendor" [ 5.413235][ T1] 0x000000c00000-0x000002c00000 : "rescue" [ 5.422709][ T1] 0x000002c00000-0x000003400000 : "kernel" [ 5.432261][ T1] 0x000003400000-0x000043400000 : "ubi" [ 5.441997][ T1] 0x000043400000-0x000100000000 : "rootfs_data"
So now it's time to dig in the kernel code to see why it was detecteded correctly (is it what you expected to see ?), but then say
Unsupported flash type 8 on /dev/mtd1
I suspect that it is not a real error, because you can see the new bootcmd2:
bootcmd2=ide reset; ext4load ide 0:1 0x00800000 /boot/uImage; ext4load ide 0:1 0x2100000 /boot/uInitrd; setenv bootargs rootdelay=10 root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial $mtdparts; bootm 0x800000 0x2100000
Also please post the content of
cat /etc/fw_env.config
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 01/29/2021 09:24PM by bodhi.
|
Re: armada 370 (88f6710) mainline uboot support January 29, 2021 11:23PM |
Registered: 8 years ago Posts: 166 |
Hi bodhi,
The output:
Also, the DSA driver in the kernel not working properly, it can't detect the network link (the network cable is pluged in lan1):
The output:
root@debian:~# cat /etc/fw_env.config # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd1 0x0000 0x100000 0x40000 4 root@debian:~# fw_printenv Unsupported flash type 8 on /dev/mtd1 CASset=min MALLOC_len=5 autoload=no baudrate=115200 bootargs=console=ttyS0,115200 bootargs_end=:10.4.50.254:255.255.255.0:KW40:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=nand read 0x2000000 0x2c00000 0x800000; bootm $loadaddr bootcmd2=ide reset; ext4load ide 0:1 0x00800000 /boot/uImage; ext4load ide 0:1 0x2100000 /boot/uInitrd; setenv bootargs rootdelay=10 root=/dev/sda1 console=ttyS0,115200 earlyprintk= serial $mtdparts; bootm 0x800000 0x2100000 bootdelay=3 cacheShare=no console=console=ttyS0,115200 disL2Cache=yes disaMvPnp=no eeeEnable=no enaAutoRecovery=yes enaClockGating=no enaFPU=no enaWrAllo=no eth1addr=00:50:43:02:00:00 eth1mtu=1500 ethact=egiga1 ethaddr=00:50:43:02:02:00 ethmtu=1500 ethprime=egiga1 image_name=uImage initrd_name=uInitrd ipaddr=192.168.1.200 loadaddr=0x02000000 loads_echo=0 mtdids=nand0=armada-nand mtdparts=mtdparts=pxa3xx_nand-0:4m(uboot),4m(uboot_env),4m(vendor),32m(rescue),8m(kernel),1024m(ubi),-(rootfs_data) mvNetConfig=mv_net_config=1,(00:50:43:11:11:11,0:1:2:3:4),mtu=1500 mv_pon_addr=00:50:43:00:00:02 nandEcc=1bit netbsd_en=no netmask=255.255.255.0 netretry=no pcieTune=no pexMode=rc pxe_files_load=:default.arm-armada370-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 rcvrip=169.254.100.100 rescueboot=nand read 0x2000000 0xc00000 0x2000000; bootm 0x2000000 rootpath=/srv/oneiric sata_delay_reset=0 sata_dma_mode=yes serverip=192.168.1.2 standalone=fsload 0x2000000 $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usb1Mode=host usb2Mode=device usbActive=1 vxworks_en=no
Also, the DSA driver in the kernel not working properly, it can't detect the network link (the network cable is pluged in lan1):
root@debian:~# ifconfig lan1 192.168.1.200 netmask 255.255.255.0
SIOCSIFFLAGS: Network is down
root@debian:~# ifconfig -a
eth0: flags=4098<BROADCAST,MULTICAST> mtu 1508
ether 00:50:43:02:02:00 txqueuelen 1024 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 34
ip6tnl0: flags=128<NOARP> mtu 1452
unspec 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 txqueuelen 1000 (UNSPEC)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lan1: flags=4098<BROADCAST,MULTICAST> mtu 1500
inet 192.168.1.200 netmask 255.255.255.0 broadcast 192.168.1.255
ether 00:11:32:21:46:bf txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lan2: flags=4098<BROADCAST,MULTICAST> mtu 1500
ether 00:11:32:21:46:bf txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lan3: flags=4098<BROADCAST,MULTICAST> mtu 1500
ether 00:11:32:21:46:bf txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lan4: flags=4098<BROADCAST,MULTICAST> mtu 1500
ether 00:11:32:21:46:bf txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=8<LOOPBACK> mtu 65536
loop txqueuelen 1000 (Local Loopback)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
sit0: flags=128<NOARP> mtu 1480
sit txqueuelen 1000 (IPv6-in-IPv4)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wan: flags=4098<BROADCAST,MULTICAST> mtu 1500
ether 00:11:32:21:46:bf txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlp1s0: flags=4098<BROADCAST,MULTICAST> mtu 1500
ether 04:54:53:0b:b4:4e txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
|
Re: armada 370 (88f6710) mainline uboot support January 30, 2021 12:47AM |
Admin Registered: 13 years ago Posts: 18,548 |
Quote
root@debian:~# cat /etc/fw_env.config
# MTD device name Device offset Env. size Flash sector size Number of sectors
/dev/mtd1 0x0000 0x100000 0x40000 4
That does not look right.
Try
# MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd1 0x0000 0x100000 0x100000
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: armada 370 (88f6710) mainline uboot support January 30, 2021 12:52AM |
Registered: 8 years ago Posts: 166 |
|
Re: armada 370 (88f6710) mainline uboot support January 30, 2021 03:40PM |
Admin Registered: 13 years ago Posts: 18,548 |
It is odd.
Try
and
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Try
# MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd1 0x0000 0x100000 0x100000 4
and
# MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd1 0x0000 0x100000 0x400000 1
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: armada 370 (88f6710) mainline uboot support January 30, 2021 08:16PM |
Registered: 8 years ago Posts: 166 |
Hi bodhi,
Still no luck, maybe the fw_printenv didn't support the mlc nand?
Still no luck, maybe the fw_printenv didn't support the mlc nand?
root@debian:~# cat /etc/fw_env.config # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd1 0x0000 0x100000 0x100000 4 root@debian:~# fw_printenv Unsupported flash type 8 on /dev/mtd1 CASset=min MALLOC_len=5 autoload=no baudrate=115200 bootargs=console=ttyS0,115200 bootargs_end=:10.4.50.254:255.255.255.0:KW40:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=nand read 0x2000000 0x2c00000 0x800000; bootm $loadaddr bootcmd2=ide reset; ext4load ide 0:1 0x00800000 /boot/uImage; ext4load ide 0:1 0x2100000 /boot/uInitrd; setenv bootargs rootdelay=10 root=/dev/sda1 console=ttyS0,115200 earlyprintk0 bootdelay=3 cacheShare=no console=console=ttyS0,115200 disL2Cache=yes disaMvPnp=no eeeEnable=no enaAutoRecovery=yes enaClockGating=no enaFPU=no enaWrAllo=no eth1addr=00:50:43:02:00:00 eth1mtu=1500 ethact=egiga1 ethaddr=00:50:43:02:02:00 ethmtu=1500 ethprime=egiga1 image_name=uImage initrd_name=uInitrd ipaddr=192.168.1.200 loadaddr=0x02000000 loads_echo=0 mtdids=nand0=armada-nand mtdparts=mtdparts=pxa3xx_nand-0:4m(uboot),4m(uboot_env),4m(vendor),32m(rescue),8m(kernel),1024m(ubi),-(rootfs_data) mvNetConfig=mv_net_config=1,(00:50:43:11:11:11,0:1:2:3:4),mtu=1500 mv_pon_addr=00:50:43:00:00:02 nandEcc=1bit netbsd_en=no netmask=255.255.255.0 netretry=no pcieTune=no pexMode=rc pxe_files_load=:default.arm-armada370-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 rcvrip=169.254.100.100 rescueboot=nand read 0x2000000 0xc00000 0x2000000; bootm 0x2000000 rootpath=/srv/oneiric sata_delay_reset=0 sata_dma_mode=yes serverip=192.168.1.2 standalone=fsload 0x2000000 $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usb1Mode=host usb2Mode=device usbActive=1 vxworks_en=no
root@debian:~# cat /etc/fw_env.config # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd1 0x0000 0x100000 0x400000 1 root@debian:~# fw_printenv Unsupported flash type 8 on /dev/mtd1 CASset=min MALLOC_len=5 autoload=no baudrate=115200 bootargs=console=ttyS0,115200 bootargs_end=:10.4.50.254:255.255.255.0:KW40:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=nand read 0x2000000 0x2c00000 0x800000; bootm $loadaddr bootcmd2=ide reset; ext4load ide 0:1 0x00800000 /boot/uImage; ext4load ide 0:1 0x2100000 /boot/uInitrd; setenv bootargs rootdelay=10 root=/dev/sda1 console=ttyS0,115200 earlyprintk= serial $mtdparts; bootm 0x800000 0x2100000 bootdelay=3 cacheShare=no console=console=ttyS0,115200 disL2Cache=yes disaMvPnp=no eeeEnable=no enaAutoRecovery=yes enaClockGating=no enaFPU=no enaWrAllo=no eth1addr=00:50:43:02:00:00 eth1mtu=1500 ethact=egiga1 ethaddr=00:50:43:02:02:00 ethmtu=1500 ethprime=egiga1 image_name=uImage initrd_name=uInitrd ipaddr=192.168.1.200 loadaddr=0x02000000 loads_echo=0 mtdids=nand0=armada-nand mtdparts=mtdparts=pxa3xx_nand-0:4m(uboot),4m(uboot_env),4m(vendor),32m(rescue),8m(kernel),1024m(ubi),-(rootfs_data) mvNetConfig=mv_net_config=1,(00:50:43:11:11:11,0:1:2:3:4),mtu=1500 mv_pon_addr=00:50:43:00:00:02 nandEcc=1bit netbsd_en=no netmask=255.255.255.0 netretry=no pcieTune=no pexMode=rc pxe_files_load=:default.arm-armada370-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 rcvrip=169.254.100.100 rescueboot=nand read 0x2000000 0xc00000 0x2000000; bootm 0x2000000 rootpath=/srv/oneiric sata_delay_reset=0 sata_dma_mode=yes serverip=192.168.1.2 standalone=fsload 0x2000000 $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usb1Mode=host usb2Mode=device usbActive=1 vxworks_en=no
|
Re: armada 370 (88f6710) mainline uboot support January 30, 2021 09:01PM |
Admin Registered: 13 years ago Posts: 18,548 |
wacke,
> Still no luck, maybe the fw_printenv didn't
> support the mlc nand?
Usually if the kernel recognizes the flash type, then mtd_utils and u-boot-tools will handle it correctly. But don't know if u-boot-tools (where fw_printenv is from) has the latest flash supports such as this MLC Micron. u-boot-tools is Debian package, so possibly it could be out-of-sync with kernel 5.10.7.
I think this is the correct one (the kernel reported this flashhas 1MB sector):
Have you tried fw_setenv to see if it works? Warning: a litlle risky to do that since there is error with fw_printenv.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> Still no luck, maybe the fw_printenv didn't
> support the mlc nand?
Usually if the kernel recognizes the flash type, then mtd_utils and u-boot-tools will handle it correctly. But don't know if u-boot-tools (where fw_printenv is from) has the latest flash supports such as this MLC Micron. u-boot-tools is Debian package, so possibly it could be out-of-sync with kernel 5.10.7.
I think this is the correct one (the kernel reported this flashhas 1MB sector):
Quote
root@debian:~# cat /etc/fw_env.config
# MTD device name Device offset Env. size Flash sector size Number of sectors
/dev/mtd1 0x0000 0x100000 0x100000 4
Have you tried fw_setenv to see if it works? Warning: a litlle risky to do that since there is error with fw_printenv.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: armada 370 (88f6710) mainline uboot support January 30, 2021 09:57PM |
Admin Registered: 13 years ago Posts: 18,548 |
wacke,
I've confirmed that fw_printenv does not have support for MLC NAND flash yet.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 2 time(s). Last edit at 01/30/2021 10:01PM by bodhi.
I've confirmed that fw_printenv does not have support for MLC NAND flash yet.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 2 time(s). Last edit at 01/30/2021 10:01PM by bodhi.
|
Re: armada 370 (88f6710) mainline uboot support January 30, 2021 10:22PM |
Registered: 8 years ago Posts: 166 |
bodhi Wrote:
-------------------------------------------------------
> wacke,
>
> I've confirmed that fw_printenv does not have
> support for MLC NAND flash yet.
Then I have to give up for now, and can you build a kernel with hw i/o patch? Also the switch seems did not working properly on the lateset kernel.
-------------------------------------------------------
> wacke,
>
> I've confirmed that fw_printenv does not have
> support for MLC NAND flash yet.
Then I have to give up for now, and can you build a kernel with hw i/o patch? Also the switch seems did not working properly on the lateset kernel.
|
Re: armada 370 (88f6710) mainline uboot support January 31, 2021 03:41PM |
Admin Registered: 13 years ago Posts: 18,548 |
wacke,
> and can you build a kernel with hw i/o patch?
That dannitool's patch for HW IO coherency did not work. Beside, it is not good for the general MVEBU kernel.
The Armada 370 kernel that I built has special configuration, as I mentioned before. So it cannot be used for your box.
It is best that you use kernel 5.10.7-mvebu-tld-1 and ignore HW IO Coherency for now.
To gain more performance for your Armada 370 box, it needs a different kernel.
> Also the switch seems
> did not working properly on the lateset kernel.
Not sure. You need to post the log when it works, and the latest log when it does not work,
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> and can you build a kernel with hw i/o patch?
That dannitool's patch for HW IO coherency did not work. Beside, it is not good for the general MVEBU kernel.
The Armada 370 kernel that I built has special configuration, as I mentioned before. So it cannot be used for your box.
It is best that you use kernel 5.10.7-mvebu-tld-1 and ignore HW IO Coherency for now.
To gain more performance for your Armada 370 box, it needs a different kernel.
> Also the switch seems
> did not working properly on the lateset kernel.
Not sure. You need to post the log when it works, and the latest log when it does not work,
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: armada 370 (88f6710) mainline uboot support March 26, 2021 09:03AM |
Registered: 8 years ago Posts: 166 |
Hi, bodhi
Something wrong with my self build uboot, it always crash when transferring large files (scp,samba etc.), but it won't crash when booting with the stock uboot.
Below is the crash log (your latest mvebu kernel 5.11.7):
Edited 1 time(s). Last edit at 03/26/2021 09:04AM by wacke.
Something wrong with my self build uboot, it always crash when transferring large files (scp,samba etc.), but it won't crash when booting with the stock uboot.
Below is the crash log (your latest mvebu kernel 5.11.7):
[ 197.305774][ T3031] 8<--- cut here --- [ 197.305788][ T3031] Unable to handle kernel paging request at virtual address 0b3ed5a2 [ 197.305802][ T3031] pgd = 453d1a27 [ 197.305812][ T3031] [0b3ed5a2] *pgd=00000000 [ 197.305829][ T3031] Internal error: Oops: 15 [#1] PREEMPT SMP ARM [ 197.305837][ T3031] Modules linked in: tag_dsa ath10k_pci ath10k_core ath9k mac80211 ath9k_common ath9k_hw libarc4 ath cfg80211 rfkill sg uio_pdrv_genirq uio mv88e6xxx dsa_core [ 197.305893][ T3031] CPU: 0 PID: 3031 Comm: sshd Not tainted 5.11.7-mvebu-tld-1 #1.0 [ 197.305903][ T3031] Hardware name: Marvell Armada 370/XP (Device Tree) [ 197.305908][ T3031] PC is at ksoftirqd_running+0x2c/0x60 [ 197.305929][ T3031] LR is at ksoftirqd_running+0x10/0x60 [ 197.305937][ T3031] pc : [<c012dac8>] lr : [<c012daac>] psr: 20000093 [ 197.305944][ T3031] sp : c4ab7c28 ip : c011d8ec fp : c1a12380 [ 197.305950][ T3031] r10: c24d709c r9 : c24d708c r8 : 00000000 [ 197.305955][ T3031] r7 : 00000042 r6 : 00000000 r5 : c24d7000 r4 : 00000000 [ 197.305961][ T3031] r3 : c0f5b2dc r2 : 2e87c000 r1 : c0d54aa9 r0 : 0b3ed5a2 [ 197.305969][ T3031] Flags: nzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment none [ 197.305978][ T3031] Control: 10c5387d Table: 04938019 DAC: 00000051 [ 197.305982][ T3031] Process sshd (pid: 3031, stack limit = 0xf569ef3f) [ 197.305990][ T3031] Stack: (0xc4ab7c28 to 0xc4ab8000) [ 197.306002][ T3031] 7c20: 60000013 c012dfd8 000001ff c012e0a0 c2660300 c09bad30 [ 197.306012][ T3031] 7c40: c1129b80 c4a8e7c0 c2660300 c4a8e7c0 c4a8ea40 c2660300 00000000 c2414400 [ 197.306023][ T3031] 7c60: 00000845 c1129b80 c1a12380 c09bce34 00044ea9 c57a4379 c241450c c09d5d58 [ 197.306033][ T3031] 7c80: c4a8e7c0 c4a8e7c0 c2660300 00000020 00000001 ea2445fd 0000002d 00000000 [ 197.306043][ T3031] 7ca0: c4ab7dc0 c09d787c 00000000 0000e800 00000000 c029a2e8 00000002 00000000 [ 197.306053][ T3031] 7cc0: 00000000 4ab2fc6d 1878bfc4 00000000 00000000 00000000 00000000 00000000 [ 197.306062][ T3031] 7ce0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 197.306072][ T3031] 7d00: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 197.306081][ T3031] 7d20: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 197.306091][ T3031] 7d40: 00000000 00000000 00000000 c57a4379 00000140 c4a8e7c0 c2660300 dee7ee83 [ 197.306102][ T3031] 7d60: c4a8ebec 00000000 00005940 00004000 c4ab7dc0 c09d8434 dee7ee83 dee7ee83 [ 197.306112][ T3031] 7d80: c4a8e7c0 00004000 c2664000 c09c8778 ef7e3380 c2fd7c00 c0cc9f18 c0cc9af5 [ 197.306122][ T3031] 7da0: ef7e3380 c4ab7ea8 00000001 00000000 c4ab6000 c4ab7e20 00000000 c4ab7e18 [ 197.306133][ T3031] 7dc0: 000000c5 00000000 0a81fc12 ef7e3380 c27d8840 c100a4bc 00000000 c57a4379 [ 197.306143][ T3031] 7de0: c0d0f238 c4a8e7c0 c1009fc8 00000040 c4ab7ea8 00000000 00004000 c4ab7e20 [ 197.306153][ T3031] 7e00: 00552b28 c09c8b9c 00000000 c4ab7e20 c4ab7e18 c02be9a0 00000002 00000000 [ 197.306164][ T3031] 7e20: 000000c5 00000000 0a81fc12 ef7e3380 000000c5 00000000 0b59472b c0aed1c0 [ 197.306174][ T3031] 7e40: 00000000 00000000 00000000 00000000 00000001 c57a4379 c4a8e7c0 00000040 [ 197.306184][ T3031] 7e60: c1009fc8 c4ab7ea8 c09c8a90 00004000 00004000 c09f6eac 00000000 c4ab7e80 [ 197.306195][ T3031] 7e80: 00000000 c57a4379 c2fc8c00 c4ab7f08 00004000 c1009fc8 c30fa400 c2fc8c00 [ 197.306205][ T3031] 7ea0: 00000000 c091752c 00000000 00000000 00000004 00000000 00000000 c4ab7f08 [ 197.306214][ T3031] 7ec0: 00000000 c10f24fc 00000000 00000000 00000000 00000040 c4ab7f20 c57a4379 [ 197.306225][ T3031] 7ee0: 00004000 c2fc8c00 00000000 c1009fc8 bee5c29c c02a6424 00004000 c0d54aa9 [ 197.306235][ T3031] 7f00: bee5c29c 00004000 00000004 00000000 00004000 c4ab7f00 00000001 c10f24fc [ 197.306245][ T3031] 7f20: c2fc8c00 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 197.306254][ T3031] 7f40: 00000000 00000000 c0100288 c57a4379 00000008 c2fc8c00 00000003 00000000 [ 197.306265][ T3031] 7f60: c1009fc8 c4ab7f7c bee5c29c c02a66cc 0c2d9619 c57a4379 c1009fc8 c2fc8c00 [ 197.306275][ T3031] 7f80: 00000000 c57a4379 00000074 00000003 005470e0 00000003 c0100288 c4ab6000 [ 197.306285][ T3031] 7fa0: 00000003 c0100060 00000074 00000003 00000003 bee5c29c 00004000 00000000 [ 197.306295][ T3031] 7fc0: 00000074 00000003 005470e0 00000003 00000003 0052bd28 0052bda8 00552b28 [ 197.306305][ T3031] 7fe0: 00000003 bee5c278 b6b3652f b6abf746 00000030 00000003 00000000 00000000 [ 197.306319][ T3031] [<c012dac8>] (ksoftirqd_running) from [<c012dfd8>] (do_softirq+0x5c/0x78) [ 197.306338][ T3031] [<c012dfd8>] (do_softirq) from [<c012e0a0>] (__local_bh_enable_ip+0xac/0xf0) [ 197.306355][ T3031] [<c012e0a0>] (__local_bh_enable_ip) from [<c09bad30>] (ip_finish_output2+0x2a4/0x3f8) [ 197.306374][ T3031] [<c09bad30>] (ip_finish_output2) from [<c09bce34>] (__ip_queue_xmit+0x288/0x2f4) [ 197.306391][ T3031] [<c09bce34>] (__ip_queue_xmit) from [<c09d787c>] (__tcp_transmit_skb+0x800/0x9c0) [ 197.306416][ T3031] [<c09d787c>] (__tcp_transmit_skb) from [<c09d8434>] (__tcp_send_ack+0xe8/0xf0) [ 197.306435][ T3031] [<c09d8434>] (__tcp_send_ack) from [<c09c8778>] (tcp_recvmsg_locked+0x4ec/0x804) [ 197.306452][ T3031] [<c09c8778>] (tcp_recvmsg_locked) from [<c09c8b9c>] (tcp_recvmsg+0x10c/0x194) [ 197.306466][ T3031] [<c09c8b9c>] (tcp_recvmsg) from [<c09f6eac>] (inet_recvmsg+0x6c/0x98) [ 197.306491][ T3031] [<c09f6eac>] (inet_recvmsg) from [<c091752c>] (sock_read_iter+0x9c/0xdc) [ 197.306518][ T3031] [<c091752c>] (sock_read_iter) from [<c02a6424>] (vfs_read+0x180/0x1d4) [ 197.306545][ T3031] [<c02a6424>] (vfs_read) from [<c02a66cc>] (ksys_read+0x68/0xb4) [ 197.306563][ T3031] [<c02a66cc>] (ksys_read) from [<c0100060>] (ret_fast_syscall+0x0/0x58) [ 197.306579][ T3031] Exception stack(0xc4ab7fa8 to 0xc4ab7ff0) [ 197.306588][ T3031] 7fa0: 00000074 00000003 00000003 bee5c29c 00004000 00000000 [ 197.306599][ T3031] 7fc0: 00000074 00000003 005470e0 00000003 00000003 0052bd28 0052bda8 00552b28 [ 197.306606][ T3031] 7fe0: 00000003 bee5c278 b6b3652f b6abf746 [ 197.306618][ T3031] Code: 1a00000b e7930002 e3500000 0a000006 (e5903000)
Edited 1 time(s). Last edit at 03/26/2021 09:04AM by wacke.
|
Re: armada 370 (88f6710) mainline uboot support June 10, 2021 07:07PM |
Registered: 8 years ago Posts: 166 |
Hi bodhi,
The attached uboot was from my self built with ext4 support and partation layout change, and have tested with no issues. Other users should flash this uboot to boot debian, or it won't boot.
Edited 1 time(s). Last edit at 06/10/2021 07:16PM by wacke.
The attached uboot was from my self built with ext4 support and partation layout change, and have tested with no issues. Other users should flash this uboot to boot debian, or it won't boot.
Edited 1 time(s). Last edit at 06/10/2021 07:16PM by wacke.
