Welcome! Log In Create A New Profile

Advanced

goflex randomly stops showing files

Posted by toddcscar 
toddcscar
goflex randomly stops showing files
December 16, 2017 10:59PM
My seagate goflex home works "some" of the time. if it loses wifi connectivity or has to be restarted it will often startup without any files in the file system. after restarting several times in a row or letting it sit overnight, it suddenly works again. Handy feature. I was able to capture one instance on boot where nothing showed up and then another boot cycles where ALL the files appeared again. Here is the section in /var/log/dmesg where it is different. Something to do with the Marvell SCSI to SATA adapter not finding the drive. When it does boot up with files, it works great: no issues.

boot when files didn't show up:

Integrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
NAND device: Manufacturer ID: 0x98, Chip ID: 0xda (Toshiba NAND 256MiB 3,3V 8-bit)

boot when files showed up.

Integrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
scsi 0:0:0:0: Direct-Access     Seagate  ST2000DL001-9VT1 CC97 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 3907029168 512-byte hardware sectors (2000399 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 3907029168 512-byte hardware sectors (2000399 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
toddcscar
Re: goflex randomly stops showing files
December 16, 2017 11:03PM
and here is the version of the Marvell SCSI SATA Driver in the log if interesting:

Marvell Development Board (LSP Version KW_LSP_4.3.4_patch22)-- SHEEVA PLUG  Soc: 88F6281 A1 LE
Re: goflex randomly stops showing files
December 17, 2017 06:02AM
toddcscar,

I am not sure what is your question? please post the entire serial bootlog (if you have it), or the entire dmesg output. And states what help you need, or what you want to do.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Author:

Your Email:


Subject:


Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: