Dockstar is flashing green after reboot

Hello,

yesterday i misconfigured my environment, so the Dockstar wont boot... no usb flashing only green led flashing

My original FW_ENV:
Pogoplug:/$ /usr/sbin/fw_printenv
ethact=egiga0
bootdelay=3
baudrate=115200
mainlineLinux=yes
console=ttyS0,115200
led_init=green blinking
led_exit=green off
led_error=orange blinking
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
mtdids=nand0=orion_nand
partition=nand0,2
stdin=serial
stdout=serial
stderr=serial
rescue_installed=0
rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params
rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
force_rescue=0
force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi
ubifs_mtd=3
ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params
ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi
usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done
usb_scan_list=1 2 3 4
usb_scan_1=usb=0:1 dev=sda1
usb_scan_2=usb=1:1 dev=sdb1
usb_scan_3=usb=2:1 dev=sdc1
usb_scan_4=usb=3:1 dev=sdd1
usb_init=run usb_scan
usb_device=0:1
usb_root=/dev/sda1
usb_rootfstype=ext2
usb_rootdelay=10
usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params
usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot
usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset
ethaddr=00:10:75:1A:C2:76
arcNumber=2097

i tried to get another usb hdd working and reconfigure my usb bootargs and bootcmd ... ;-(

Can i restore to my defaults with a serial Nokia cable?

thx in advance

Yes, serial console can set the uboot environment variables.

Thx for your answer@dpffan,
i will buy a Nokia Ca42 usb2serial... and give it a try.
My usb2serial doesn´t work... FTDI, cause the power is ~6V and not 3.3.
Hope that my serial connection is not fried ..

Okay, i connectect the cable.
This is my output:

Marvell>>

U-Boot 2010.09 (Oct 23 2010 - 11:49:22)
Marvell-Dockstar/Pogoplug by Jeff Doozan

SoC: Kirkwood 88F6281_A0
DRAM: 128 MiB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
Marvell>>

Marvell>> printenv
ethact=egiga0
baudrate=115200
mainlineLinux=yes
console=ttyS0,115200
led_init=green blinking
led_exit=green off
led_error=orange blinking
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
mtdids=nand0=orion_nand
partition=nand0,2
rescue_installed=0
rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params
rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
force_rescue=0
force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi
ubifs_mtd=3
ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params
ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi
usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done
usb_scan_list=1 2 3 4
usb_scan_1=usb=0:1 dev=sda1
usb_scan_2=usb=1:1 dev=sdb1
usb_scan_3=usb=2:1 dev=sdc1
usb_scan_4=usb=3:1 dev=sdd1
usb_init=run usb_scan
usb_device=0:1
usb_root=/dev/sda1
usb_rootfstype=ext2
usb_rootdelay=10
usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params
usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot
usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
ethaddr=00:10:75:1A:C2:76
arcNumber=2097
bootcmd=usb=start
stdin=serial
stdout=serial
stderr=serial

Environment size: 2132/131068 bytes

There´s no booting from USb device anymore, how can i fix/restore to my defaults?

thx





88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
Using egiga0 device
host 192.168.1.1 is alive
## Error: "bootcmd_usb" not defined
Using egiga0 device
host 192.168.1.1 is alive
## Error: "bootcmd_usb" not defined
## Error: "bootcmd_original" not defined
Marvell>>


After insering these command my Dockstar is in sh prompt:
setenv bootcmd 'usb start; run force_rescue_bootcmd; run usb_bootcmd; usb stop; run bootcmd_ubi; run rescue_bootcmd; run pogo_bootcmd; reset'

i can install a new debian to my usb device and it boots. After that i installed the System Rescue V2 on flash.
My original/modified pogoplug environment is gone, is it needful to restore it back or can i use the rescue environment instead of pogo?



Edited 2 time(s). Last edit at 10/08/2011 02:23PM by fhu2010.

fhu2010 Wrote:
-------------------------------------------------------
> My original/modified pogoplug environment is gone,
> is it needful to restore it back or can i use the
> rescue environment instead of pogo?
Do you used or want the my.pogoplug service? If not then you don't pogoplug environment.

@laprjns:

no i don´t need the original Pogoplug service, only the "hacked" without phone home.
I think my system is stable now, my recovery works well and don´t touch my running system...

thx and br
fhu