Pogoplug 4 uboot update won't boot May 21, 2018 07:28PM |
Registered: 9 years ago Posts: 35 |
U-Boot 2016.09.01-1 (Oct 10 2016 - 23:13:37 -0600) Arch Linux ARM Pogoplug V4 gcc (GCC) 6.2.1 20160830 GNU ld (GNU Binutils) 2.27 Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 6 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Reset IDE: ide_preinit failed switch to partitions #0, OK mmc0 is current device mmc found on device 0 Checking for: /boot/uEnv.txt ... ** File not found /boot/zImage ** 4600064 bytes read in 127 ms (34.5 MiB/s) loading /boot/dtbs/kirkwood-pogoplug-series-4.dtb ... ** File not found /boot/dtbs/kirkwood-pogoplug-series-4.dtb ** 5615605 bytes read in 154 ms (34.8 MiB/s) Booting uImage with initrd ## Booting kernel from Legacy Image at 00810000 ... Image Name: Linux-4.4.97-1-ARCH Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4600000 Bytes = 4.4 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK
U-Boot 2016.09.01-1 (Oct 10 2016 - 23:13:37 -0600) Arch Linux ARM Pogoplug V4 gcc (GCC) 6.2.1 20160830 GNU ld (GNU Binutils) 2.27 Hit any key to stop autoboot: 3 6 0 Pogoplugv4> Pogoplugv4> printenv printenv bootcmd=run startboot;run bootubi bootdir=/boot bootfilem=uImage bootfilez=zImage bootubi=echo Trying to boot from NAND ...;if run mountubi; then ubifsload ${loadaddr} /boot/zImage;ubifsload ${fdtaddr} /boot/dtbs/kirkwood-pogoplugv4.dtb; ubifsumount; setenv bootargs console=${console} ubi.mtd=1 root=ubi0:rootfs ro rootfstype=ubifs rootwait ${mtdparts};bootz ${loadaddr} - ${fdtaddr};fi console=ttyS0,115200 ethact=egiga0 ethaddr=00:25:31:05:09:c6 fdtaddr=0x800000 fdtdir=/boot/dtbs fdtfile=kirkwood-pogoplug-series-4.dtb ipaddr=10.10.10.3 loadaddr=0x810000 loadfdt=echo loading ${fdtdir}/${fdtfile} ...; load ${devtype} ${bootpart} ${fdtaddr} ${fdtdir}/${fdtfile} loadimage=load ${devtype} ${bootpart} ${loadaddr} ${bootdir}/${bootfilez} || load ${devtype} ${bootpart} ${loadaddr} ${bootdir}/${bootfilem} loadrd=load ${devtype} ${bootpart} ${rdaddr} ${bootdir}/${rdfile} mainargs=setenv bootargs console=${console} ${mtdparts} root=${root} rw rootwait ${optargs} ${ncargs} mountubi=ubi part rootfs; ubifsmount ubi0:rootfs mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),-(rootfs) ncargs=ignore_loglevel netconsole=6665@10.10.10.3/eth0,6666@10.10.10.4/ ncip=10.10.10.5 ncipk=10.10.10.4 netconsole=on preboot=if env exists netconsole && test ${netconsole} = on; then if ping ${ncip}; then setenv stdin nc; setenv stdout nc; setenv stderr nc; version; if env exists ncargsusr; then echo ncargs has been defined by user; setenv ncargs ${ncargsusr}; else setenv ncargs ignore_loglevel netconsole=6665@${ipaddr}/eth0,6666@${ncipk}/; fi; fi; else echo Netconsole has been turned off.; echo To turn it on, set netconsole variable to on.; setenv stdin; setenv stdout; setenv stderr; setenv ncargs; fi rdaddr=0x1100000 rdfile=initramfs-linux.img startboot=usb start; ide reset; for devtype in mmc usb ide; do setenv devnum 0; while ${devtype} dev ${devnum}; do echo ${devtype} found on device ${devnum}; setenv bootpart ${devnum}:1; echo Checking for: ${bootdir}/uEnv.txt ...; if test -e ${devtype} ${bootpart} ${bootdir}/uEnv.txt; then load ${devtype} ${bootpart} ${loadaddr} ${bootdir}/uEnv.txt; env import -t ${loadaddr} ${filesize}; echo Loaded environment from ${bootdir}/uEnv.txt; echo Checking if uenvcmd is set ...; if test -n ${uenvcmd}; then echo Running uenvcmd ...; run uenvcmd; fi; fi; if run loadimage; then if env exists root; then echo root has been defined by user; else part uuid ${devtype} ${bootpart} uuid; setenv root PARTUUID=${uuid}; fi; run mainargs; if run loadfdt; then if run loadrd; then bootz ${loadaddr} ${rdaddr}:${filesize} ${fdtaddr}; else bootz ${loadaddr} - ${fdtaddr}; fi; else if run loadrd; then echo Booting uImage with initrd; bootm ${loadaddr} ${rdaddr}:${filesize}; else bootm ${loadaddr}; fi; fi; else echo No kernel found; fi; setexpr devnum ${devnum} + 1; done; done; stderr=nc stdin=nc stdout=nc Environment size: 2928/131068 bytes Pogoplugv4>
Re: Pogoplug 4 uboot update won't boot May 21, 2018 09:25PM |
Registered: 10 years ago Posts: 1,303 |
> U-Boot 2016.09.01-1 (Oct 10 2016 - 23:13:37 -0600) > Arch Linux ARM > Pogoplug V4 > gcc (GCC) 6.2.1 20160830 > GNU ld (GNU Binutils) 2.27 > Hit any key to stop autoboot: 0 > starting USB... > USB0: USB EHCI 1.00 > scanning bus 0 for devices... 6 > 1 USB Device(s) found > scanning usb for storage devices... 0 > Storage Device(s) found > > Reset IDE: ide_preinit failed > switch to partitions #0, OK > mmc0 is current device > mmc found on device 0 > Checking for: /boot/uEnv.txt ... > ** File not found /boot/zImage ** > 4600064 bytes read in 127 ms (34.5 MiB/s) > loading /boot/dtbs/kirkwood-pogoplug-series-4.dtb ... > ** File not found /boot/dtbs/kirkwood-pogoplug-series-4.dtb ** >>
Re: Pogoplug 4 uboot update won't boot May 22, 2018 01:24AM |
Admin Registered: 13 years ago Posts: 18,495 |
Quote
mmc0 is current device
mmc found on device 0
Booting uImage with initrd
## Booting kernel from Legacy Image at 00810000 ...
Image Name: Linux-4.4.97-1-ARCH
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4600000 Bytes = 4.4 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Above is how far it gets in netconsole
Re: Pogoplug 4 uboot update won't boot May 22, 2018 06:10AM |
Registered: 10 years ago Posts: 1,303 |
Re: Pogoplug 4 uboot update won't boot May 22, 2018 09:48PM |
Registered: 9 years ago Posts: 35 |
Re: Pogoplug 4 uboot update won't boot June 03, 2018 07:55PM |
Registered: 9 years ago Posts: 35 |
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:34:01 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: MVEBU_MMC: 0 In: serial Out: serial Err: serial Net: egiga0 Using egiga0 device host 192.168.0.103 is alive Using egiga0 device host 192.168.0.103 is alive Using egiga0 device host 192.168.0.103 is alive Using egiga0 device host 192.168.0.103 is alive Using egiga0 device host 192.168.0.103 is alive [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.97-1-ARCH (builduser@leming) (gcc version 7.2.0 (GCC) ) #1 PREEMPT Sat Nov 11 04:51:38 UTC 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: Pogoplug V4 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32480 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:1M(u-boot),-(rootfs) [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 119688K/131072K available (6598K kernel code, 550K rwdata, 1880K rodata, 304K init, 725K bss, 11384K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc084fc70 (8480 kB) [ 0.000000] .init : 0xc0850000 - 0xc089c000 ( 304 kB) [ 0.000000] .data : 0xc089c000 - 0xc0925a04 ( 551 kB) [ 0.000000] .bss : 0xc0925a04 - 0xc09daf98 ( 726 kB) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] .Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:114 [ 0.000016] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns [ 4.505952] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns [ 4.506181] Console: colour dummy device 80x30 [ 4.506216] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) [ 4.596040] pid_max: default: 32768 minimum: 301 [ 4.596147] Security Framework initialized [ 4.596233] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 4.596254] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 4.597128] Initializing cgroup subsys io [ 4.597168] Initializing cgroup subsys memory [ 4.597230] Initializing cgroup subsys devices [ 4.597260] Initializing cgroup subsys freezer [ 4.597286] Initializing cgroup subsys net_cls [ 4.597308] Initializing cgroup subsys perf_event [ 4.597334] Initializing cgroup subsys net_prio [ 4.597430] CPU: Testing write buffer coherency: ok [ 4.597974] Setting up static identity map for 0x81e0 - 0x8238 [ 4.600274] devtmpfs: initialized [ 4.603076] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 4.603122] futex hash table entries: 256 (order: -1, 3072 bytes) [ 4.603744] pinctrl core: initialized pinctrl subsystem [ 4.604646] NET: Registered protocol family 16 [ 4.605243] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 4.636057] cpuidle: using governor ladder [ 4.666054] cpuidle: using governor menu [ 4.666245] Kirkwood: MV88F6281-A1, TCLK=166666667. [ 4.666274] Feroceon L2: Enabling L2 [ 4.666314] Feroceon L2: Cache support initialised. [ 4.668934] Kirkwood PCIe port 0: link down [ 4.668946] PCI: bus0 uses PCIe port 0 [ 4.669216] PCI host bridge to bus 0000:00 [ 4.669237] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] [ 4.669250] pci_bus 0000:00: root bus resource [io 0x1000-0xffff] [ 4.669262] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 4.669676] PCI: bus0: Fast back to back transfers disabled [ 4.707760] vgaarb: loaded [ 4.708130] SCSI subsystem initialized [ 4.708710] usbcore: registered new interface driver usbfs [ 4.708797] usbcore: registered new interface driver hub [ 4.708864] usbcore: registered new device driver usb [ 4.709041] pps_core: LinuxPPS API ver. 1 registered [ 4.709052] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 4.709089] PTP clock support registered [ 4.710308] clocksource: Switched to clocksource orion_clocksource [ 4.756643] FS-Cache: Loaded [ 4.771581] NET: Registered protocol family 2 [ 4.772479] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 4.772509] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 4.772532] TCP: Hash tables configured (established 1024 bind 1024) [ 4.772623] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 4.772649] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 4.772869] NET: Registered protocol family 1 [ 4.773246] RPC: Registered named UNIX socket transport module. [ 4.773260] RPC: Registered udp transport module. [ 4.773267] RPC: Registered tcp transport module. [ 4.773275] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 4.790414] VFS: Disk quotas dquot_6.6.0 [ 4.790735] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 4.793128] FS-Cache: Netfs 'nfs' registered for caching [ 4.794440] NFS: Registering the id_resolver key type [ 4.794514] Key type id_resolver registered [ 4.794523] Key type id_legacy registered [ 4.794629] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 4.796166] fuse init (API version 7.23) [ 4.798635] aufs 4.4-20170911 [ 4.804640] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) [ 4.804664] io scheduler noop registered [ 4.804678] io scheduler deadline registered [ 4.804985] io scheduler cfq registered [ 4.805288] io scheduler bfq registered (default) [ 4.805298] BFQ I/O-scheduler: v7r11 [ 4.805543] mv_xor mv_xor.0: Marvell shared XOR driver [ 4.841739] mv_xor mv_xor.0: Marvell XOR (Registers Mode): ( xor cpy ) [ 4.842019] mv_xor mv_xor.1: Marvell shared XOR driver [ 4.881756] mv_xor mv_xor.1: Marvell XOR (Registers Mode): ( xor cpy ) [ 4.888238] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 4.889462] console [ttyS0] disabled [ 4.909559] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 10416666) is a 16550A [ 5.495234] console [ttyS0] enabled [ 5.517146] brd: module loaded [ 5.529099] loop: module loaded [ 5.532742] sata_mv sata_mv.0: cannot get optional clkdev [ 5.538189] sata_mv sata_mv.0: slots 32 ports 1 [ 5.544709] scsi host0: sata_mv [ 5.548264] ata1: SATA max UDMA/133 irq 21 [ 5.553249] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 5.559574] nand: Hynix H27U1G8F2BTR-BC [ 5.563556] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 5.571127] Scanning device for bad blocks [ 5.592134] Bad eraseblock 208 at 0x000001a00000 [ 5.616609] Bad eraseblock 454 at 0x0000038c0000 [ 5.644907] Bad eraseblock 747 at 0x000005d60000 [ 5.658207] Bad eraseblock 855 at 0x000006ae0000 [ 5.676438] 2 cmdlinepart partitions found on MTD device orion_nand [ 5.682695] Creating 2 MTD partitions on "orion_nand": [ 5.687817] 0x000000000000-0x000000100000 : "u-boot" [ 5.693359] 0x000000100000-0x000008000000 : "rootfs" [ 5.708038] libphy: orion_mdio_bus: probed [ 5.712297] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 5.910340] ata1: SATA link down (SStatus 0 SControl F300) [ 6.795985] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:05:09:c6 [ 6.804861] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 6.811388] ehci-pci: EHCI PCI platform driver [ 6.815901] ehci-orion: EHCI orion driver [ 6.819974] orion-ehci orion-ehci.0: EHCI Host Controller [ 6.825397] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 [ 6.833113] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000 [ 6.850347] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00 [ 6.857363] hub 1-0:1.0: USB hub found [ 6.861191] hub 1-0:1.0: 1 port detected [ 6.865950] usbcore: registered new interface driver uas [ 6.871462] usbcore: registered new interface driver usb-storage [ 6.877512] usbcore: registered new interface driver ums-alauda [ 6.883515] usbcore: registered new interface driver ums-cypress [ 6.889556] usbcore: registered new interface driver ums-datafab [ 6.895622] usbcore: registered new interface driver ums_eneub6250 [ 6.901854] usbcore: registered new interface driver ums-freecom [ 6.907889] usbcore: registered new interface driver ums-isd200 [ 6.913864] usbcore: registered new interface driver ums-jumpshot [ 6.919991] usbcore: registered new interface driver ums-karma [ 6.925874] usbcore: registered new interface driver ums-onetouch [ 6.932043] usbcore: registered new interface driver ums-realtek [ 6.938078] usbcore: registered new interface driver ums-sddr09 [ 6.944053] usbcore: registered new interface driver ums-sddr55 [ 6.950000] usbcore: registered new interface driver ums-usbat [ 6.956344] mousedev: PS/2 mouse device common for all mice [ 7.970336] rtc-mv rtc-mv: internal RTC not ticking [ 7.975333] i2c /dev entries driver [ 7.979447] sdhci: Secure Digital Host Controller Interface driver [ 7.985627] sdhci: Copyright(c) Pierre Ossman [ 8.020574] sdhci-pltfm: SDHCI platform and OF driver helper [ 8.029860] ledtrig-cpu: registered to indicate activity on CPUs [ 8.036051] usbcore: registered new interface driver r8712u [ 8.041926] gre: GRE over IPv4 demultiplexor driver [ 8.046883] NET: Registered protocol family 17 [ 8.051520] Key type dns_resolver registered [ 8.060015] registered taskstats version 1 [ 8.066211] Key type encrypted registered [ 8.070959] console [netcon0] enabled [ 8.074610] netconsole: network logging started [ 8.079562] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 8.086697] hctosys: unable to open rtc device (rtc0) [ 8.093285] Waiting 10 sec before mounting root device... [ 8.104662] mmc0: host does not support reading read-only switch, assuming write-enable [ 8.116837] mmc0: new high speed SDHC card at address 0007 [ 8.122973] mmcblk0: mmc0:0007 SD32G 28.9 GiB [ 8.129384] mmcblk0: p1 [ 18.100609] VFS: Cannot open root device "LABEL=rootfs" or unknown-block(0,0): error -6 [ 18.108580] Please append a correct "root=" boot option; here are the available partitions: [ 18.116987] 0100 8192 ram0 (driver?) [ 18.121641] 0101 8192 ram1 (driver?) [ 18.126243] 0102 8192 ram2 (driver?) [ 18.130892] 0103 8192 ram3 (driver?) [ 18.135497] 0104 8192 ram4 (driver?) [ 18.140102] 0105 8192 ram5 (driver?) [ 18.144743] 0106 8192 ram6 (driver?) [ 18.149346] 0107 8192 ram7 (driver?) [ 18.153970] 0108 8192 ram8 (driver?) [ 18.158574] 0109 8192 ram9 (driver?) [ 18.163197] 010a 8192 ram10 (driver?) [ 18.167888] 010b 8192 ram11 (driver?) [ 18.172598] 010c 8192 ram12 (driver?) [ 18.177288] 010d 8192 ram13 (driver?) [ 18.181998] 010e 8192 ram14 (driver?) [ 18.186688] 010f 8192 ram15 (driver?) [ 18.191403] b300 30322688 mmcblk0 driver: mmcblk [ 18.196702] b301 30322656 mmcblk0p1 00000000-01 [ 18.202016] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 18.210242] CPU: 0 PID: 1 Comm: swapper Not tainted 4.4.97-1-ARCH #1 [ 18.216560] Hardware name: Pogoplug V4 [ 18.220316] [<c001047c>] (unwind_backtrace) from [<c000d978>] (show_stack+0x10/0x14) [ 18.228029] [<c000d978>] (show_stack) from [<c00cd690>] (panic+0x88/0x208) [ 18.234883] [<c00cd690>] (panic) from [<c08512c0>] (mount_block_root+0x1b8/0x278) [ 18.242334] [<c08512c0>] (mount_block_root) from [<c0851570>] (mount_root+0xf4/0x120) [ 18.250136] [<c0851570>] (mount_root) from [<c08516f4>] (prepare_namespace+0x158/0x1b8) [ 18.258111] [<c08516f4>] (prepare_namespace) from [<c0850e98>] (kernel_init_freeable+0x1f8/0x24c) [ 18.266958] [<c0850e98>] (kernel_init_freeable) from [<c0646e40>] (kernel_init+0x8/0xe8) [ 18.275020] [<c0646e40>] (kernel_init) from [<c000a4b0>] (ret_from_fork+0x14/0x24) [ 18.282562] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
arcNumber=3960 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-pogoplug_v4.dtb ethact=egiga0 ethaddr=00:25:31:05:09:c6 if_netconsole=ping $serverip ipaddr=192.168.0.183 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 machid=f78 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),-(rootfs) nc_ready=0 partition=nand0,2 preboot=run preboot_nc preboot_nc=setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.103 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_ready_retry=15 Environment size: 3013/131068 bytes
Re: Pogoplug 4 uboot update won't boot June 03, 2018 11:20PM |
Registered: 9 years ago Posts: 437 |
Re: Pogoplug 4 uboot update won't boot June 04, 2018 12:23AM |
Admin Registered: 13 years ago Posts: 18,495 |
2017.07-tld-1 (Sep 05 2017 - 00:34:01 -0700) Pogoplug V4 .... host 192.168.0.103 is alive Using egiga0 device host 192.168.0.103 is alive
Re: Pogoplug 4 uboot update won't boot June 04, 2018 12:11PM |
Registered: 9 years ago Posts: 35 |
Re: Pogoplug 4 uboot update won't boot June 04, 2018 05:05PM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: Pogoplug 4 uboot update won't boot June 04, 2018 07:14PM |
Registered: 9 years ago Posts: 35 |
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:34:01 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: MVEBU_MMC: 0 In: serial Out: serial Err: serial Net: egiga0 No link on egiga0 ping failed; host 192.168.0.103 is not alive No link on egiga0 ping failed; host 192.168.0.103 is not alive No link on egiga0 ping failed; host 192.168.0.103 is not alive No link on egiga0 ping failed; host 192.168.0.103 is not alive No link on egiga0 ping failed; host 192.168.0.103 is not alive Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Reset IDE: ide_preinit failed MMC rescan: current device # 0 initialized OK ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... ** Bad device usb 0 ** no IDE devices available Partition Map for MMC device 0 -- Partition Type: DOS Part.Start Sector.Num Sectors.UUID..Type 1.63 .60645312 .00000000-01.83 loading envs from mmc 0 ... ** File not found /boot/uEnv.txt ** running scan_disk ... Scan device usb device usb 0:1 ** Bad device usb 0 ** device usb 1:1 ** Bad device usb 1 ** device usb 2:1 ** Bad device usb 2 ** device usb 3:1 ** Bad device usb 3 ** Scan device ide Reset IDE: ide_preinit failed device ide 0:1 ** Bad device ide 0 ** device ide 1:1 ** Bad device ide 1 ** device ide 2:1 ** Bad device ide 2 ** device ide 3:1 ** Bad device ide 3 ** Scan device mmc MMC rescan: current device # 0 initialized OK device mmc 0:1 1 bytes read in 11 ms (0 Bytes/s) Found bootable drive on mmc 0 loading uImage ... 4600064 bytes read in 127 ms (34.5 MiB/s) loading uInitrd ... ** File not found /boot/uInitrd ** loading DTB /boot/dts/kirkwood-pogoplug_v4.dtb ... ** File not found /boot/dts/kirkwood-pogoplug_v4.dtb ** ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.4.97-1-ARCH Created: 2017-11-11 4:51:55 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4600000 Bytes = 4.4 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK Using machid 0xf78 from environment Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.97-1-ARCH (builduser@leming) (gcc version 7.2.0 (GCC) ) #1 PREEMPT Sat Nov 11 04:51:38 UTC 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: Pogoplug V4 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32480 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:1M(u-boot),-(rootfs) [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 119688K/131072K available (6598K kernel code, 550K rwdata, 1880K rodata, 304K init, 725K bss, 11384K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc084fc70 (8480 kB) [ 0.000000] .init : 0xc0850000 - 0xc089c000 ( 304 kB) [ 0.000000] .data : 0xc089c000 - 0xc0925a04 ( 551 kB) [ 0.000000] .bss : 0xc0925a04 - 0xc09daf98 ( 726 kB) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] .Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:114 [ 0.000017] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns [ 8.240278] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns [ 8.240508] Console: colour dummy device 80x30 [ 8.240542] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) [ 8.330367] pid_max: default: 32768 minimum: 301 [ 8.330472] Security Framework initialized [ 8.330557] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 8.330578] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 8.331449] Initializing cgroup subsys io [ 8.331488] Initializing cgroup subsys memory [ 8.331550] Initializing cgroup subsys devices [ 8.331579] Initializing cgroup subsys freezer [ 8.331603] Initializing cgroup subsys net_cls [ 8.331624] Initializing cgroup subsys perf_event [ 8.331651] Initializing cgroup subsys net_prio [ 8.331747] CPU: Testing write buffer coherency: ok [ 8.332291] Setting up static identity map for 0x81e0 - 0x8238 [ 8.334589] devtmpfs: initialized [ 8.337360] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 8.337409] futex hash table entries: 256 (order: -1, 3072 bytes) [ 8.337995] pinctrl core: initialized pinctrl subsystem [ 8.338896] NET: Registered protocol family 16 [ 8.339493] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 8.370382] cpuidle: using governor ladder [ 8.400379] cpuidle: using governor menu [ 8.400570] Kirkwood: MV88F6281-A1, TCLK=166666667. [ 8.400600] Feroceon L2: Enabling L2 [ 8.400641] Feroceon L2: Cache support initialised. [ 8.403263] Kirkwood PCIe port 0: link down [ 8.403275] PCI: bus0 uses PCIe port 0 [ 8.403544] PCI host bridge to bus 0000:00 [ 8.403565] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] [ 8.403578] pci_bus 0000:00: root bus resource [io 0x1000-0xffff] [ 8.403590] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 8.404004] PCI: bus0: Fast back to back transfers disabled [ 8.442080] vgaarb: loaded [ 8.442451] SCSI subsystem initialized [ 8.443031] usbcore: registered new interface driver usbfs [ 8.443117] usbcore: registered new interface driver hub [ 8.443183] usbcore: registered new device driver usb [ 8.443362] pps_core: LinuxPPS API ver. 1 registered [ 8.443372] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 8.443409] PTP clock support registered [ 8.444626] clocksource: Switched to clocksource orion_clocksource [ 8.490956] FS-Cache: Loaded [ 8.505910] NET: Registered protocol family 2 [ 8.506814] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 8.506845] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 8.506867] TCP: Hash tables configured (established 1024 bind 1024) [ 8.506959] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 8.506985] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 8.507205] NET: Registered protocol family 1 [ 8.507578] RPC: Registered named UNIX socket transport module. [ 8.507592] RPC: Registered udp transport module. [ 8.507600] RPC: Registered tcp transport module. [ 8.507608] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 8.524762] VFS: Disk quotas dquot_6.6.0 [ 8.525082] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 8.527475] FS-Cache: Netfs 'nfs' registered for caching [ 8.528783] NFS: Registering the id_resolver key type [ 8.528838] Key type id_resolver registered [ 8.528847] Key type id_legacy registered [ 8.528952] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 8.530486] fuse init (API version 7.23) [ 8.532952] aufs 4.4-20170911 [ 8.538943] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) [ 8.538965] io scheduler noop registered [ 8.538980] io scheduler deadline registered [ 8.539289] io scheduler cfq registered [ 8.539590] io scheduler bfq registered (default) [ 8.539600] BFQ I/O-scheduler: v7r11 [ 8.539845] mv_xor mv_xor.0: Marvell shared XOR driver [ 8.576057] mv_xor mv_xor.0: Marvell XOR (Registers Mode): ( xor cpy ) [ 8.576335] mv_xor mv_xor.1: Marvell shared XOR driver [ 8.616069] mv_xor mv_xor.1: Marvell XOR (Registers Mode): ( xor cpy ) [ 8.622554] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 8.623778] console [ttyS0] disabled [ 8.643874] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 10416666) is a 16550A [ 9.229547] console [ttyS0] enabled [ 9.251485] brd: module loaded [ 9.263452] loop: module loaded [ 9.267097] sata_mv sata_mv.0: cannot get optional clkdev [ 9.272545] sata_mv sata_mv.0: slots 32 ports 1 [ 9.279064] scsi host0: sata_mv [ 9.282615] ata1: SATA max UDMA/133 irq 21 [ 9.287602] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 9.293931] nand: Hynix H27U1G8F2BTR-BC [ 9.297913] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 9.305483] Scanning device for bad blocks [ 9.326489] Bad eraseblock 208 at 0x000001a00000 [ 9.350968] Bad eraseblock 454 at 0x0000038c0000 [ 9.379262] Bad eraseblock 747 at 0x000005d60000 [ 9.392566] Bad eraseblock 855 at 0x000006ae0000 [ 9.410797] 2 cmdlinepart partitions found on MTD device orion_nand [ 9.417050] Creating 2 MTD partitions on "orion_nand": [ 9.422174] 0x000000000000-0x000000100000 : "u-boot" [ 9.427711] 0x000000100000-0x000008000000 : "rootfs" [ 9.442441] libphy: orion_mdio_bus: probed [ 9.446700] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 9.644657] ata1: SATA link down (SStatus 0 SControl F300) [ 10.530282] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:05:09:c6 [ 10.539156] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 10.545683] ehci-pci: EHCI PCI platform driver [ 10.550197] ehci-orion: EHCI orion driver [ 10.554269] orion-ehci orion-ehci.0: EHCI Host Controller [ 10.559694] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 [ 10.567409] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000 [ 10.584664] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00 [ 10.591681] hub 1-0:1.0: USB hub found [ 10.595515] hub 1-0:1.0: 1 port detected [ 10.600277] usbcore: registered new interface driver uas [ 10.605794] usbcore: registered new interface driver usb-storage [ 10.611840] usbcore: registered new interface driver ums-alauda [ 10.617846] usbcore: registered new interface driver ums-cypress [ 10.623886] usbcore: registered new interface driver ums-datafab [ 10.629952] usbcore: registered new interface driver ums_eneub6250 [ 10.636185] usbcore: registered new interface driver ums-freecom [ 10.642219] usbcore: registered new interface driver ums-isd200 [ 10.648194] usbcore: registered new interface driver ums-jumpshot [ 10.654322] usbcore: registered new interface driver ums-karma [ 10.660206] usbcore: registered new interface driver ums-onetouch [ 10.666374] usbcore: registered new interface driver ums-realtek [ 10.672409] usbcore: registered new interface driver ums-sddr09 [ 10.678383] usbcore: registered new interface driver ums-sddr55 [ 10.684331] usbcore: registered new interface driver ums-usbat [ 10.690674] mousedev: PS/2 mouse device common for all mice [ 11.704653] rtc-mv rtc-mv: internal RTC not ticking [ 11.709654] i2c /dev entries driver [ 11.713761] sdhci: Secure Digital Host Controller Interface driver [ 11.719940] sdhci: Copyright(c) Pierre Ossman [ 11.754893] sdhci-pltfm: SDHCI platform and OF driver helper [ 11.764179] ledtrig-cpu: registered to indicate activity on CPUs [ 11.770363] usbcore: registered new interface driver r8712u [ 11.776238] gre: GRE over IPv4 demultiplexor driver [ 11.781179] NET: Registered protocol family 17 [ 11.785793] Key type dns_resolver registered [ 11.794311] registered taskstats version 1 [ 11.800512] Key type encrypted registered [ 11.805260] console [netcon0] enabled [ 11.808905] netconsole: network logging started [ 11.813860] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 11.820995] hctosys: unable to open rtc device (rtc0) [ 11.827577] Waiting 10 sec before mounting root device... [ 11.839012] mmc0: host does not support reading read-only switch, assuming write-enable [ 11.851190] mmc0: new high speed SDHC card at address 0007 [ 11.857324] mmcblk0: mmc0:0007 SD32G 28.9 GiB [ 11.863704] mmcblk0: p1 [ 21.834925] VFS: Cannot open root device "LABEL=rootfs" or unknown-block(0,0): error -6 [ 21.842892] Please append a correct "root=" boot option; here are the available partitions: [ 21.851303] 0100 8192 ram0 (driver?) [ 21.855954] 0101 8192 ram1 (driver?) [ 21.860557] 0102 8192 ram2 (driver?) [ 21.865206] 0103 8192 ram3 (driver?) [ 21.869810] 0104 8192 ram4 (driver?) [ 21.874415] 0105 8192 ram5 (driver?) [ 21.879056] 0106 8192 ram6 (driver?) [ 21.883660] 0107 8192 ram7 (driver?) [ 21.888283] 0108 8192 ram8 (driver?) [ 21.892887] 0109 8192 ram9 (driver?) [ 21.897511] 010a 8192 ram10 (driver?) [ 21.902201] 010b 8192 ram11 (driver?) [ 21.906912] 010c 8192 ram12 (driver?) [ 21.911601] 010d 8192 ram13 (driver?) [ 21.916311] 010e 8192 ram14 (driver?) [ 21.921002] 010f 8192 ram15 (driver?) [ 21.925717] b300 30322688 mmcblk0 driver: mmcblk [ 21.931015] b301 30322656 mmcblk0p1 00000000-01 [ 21.936329] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 21.944555] CPU: 0 PID: 1 Comm: swapper Not tainted 4.4.97-1-ARCH #1 [ 21.950874] Hardware name: Pogoplug V4 [ 21.954638] [<c001047c>] (unwind_backtrace) from [<c000d978>] (show_stack+0x10/0x14) [ 21.962351] [<c000d978>] (show_stack) from [<c00cd690>] (panic+0x88/0x208) [ 21.969204] [<c00cd690>] (panic) from [<c08512c0>] (mount_block_root+0x1b8/0x278) [ 21.976657] [<c08512c0>] (mount_block_root) from [<c0851570>] (mount_root+0xf4/0x120) [ 21.984457] [<c0851570>] (mount_root) from [<c08516f4>] (prepare_namespace+0x158/0x1b8) [ 21.992432] [<c08516f4>] (prepare_namespace) from [<c0850e98>] (kernel_init_freeable+0x1f8/0x24c) [ 22.001281] [<c0850e98>] (kernel_init_freeable) from [<c0646e40>] (kernel_init+0x8/0xe8) [ 22.009342] [<c0646e40>] (kernel_init) from [<c000a4b0>] (ret_from_fork+0x14/0x24) [ 22.016884] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 96.744648] random: nonblocking pool is initialized
Re: Pogoplug 4 uboot update won't boot June 04, 2018 08:03PM |
Admin Registered: 13 years ago Posts: 18,495 |
> ## Booting kernel from Legacy Image at 00800000 > ... > Image Name: Linux-4.4.97-1-ARCH > Created: 2017-11-11 4:51:55 UTC > Image Type: ARM Linux Kernel Image > (uncompressed) > Data Size: 4600000 Bytes = 4.4 MiB > Load Address: 00008000 > Entry Point: 00008000 > Verifying Checksum ... OK > Loading Kernel Image ... OK > Using machid 0xf78 from environment
> [ 0.000000] Kernel command line: > console=ttyS0,115200 root=LABEL=rootfs > rootdelay=10 > mtdparts=orion_nand:1M(u-boot),-(rootfs)
setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=/dev/mmcblk0p1 rootdelay=10 $mtdparts $custom_paramsand then boot
boot
Re: Pogoplug 4 uboot update won't boot June 04, 2018 08:45PM |
Registered: 9 years ago Posts: 35 |
Re: Pogoplug 4 uboot update won't boot June 04, 2018 09:44PM |
Admin Registered: 13 years ago Posts: 18,495 |
Quote
Updated 24 Jul 2017:
Basic Debian stretch Kirkwood rootfs for most Kirwood plugs:
- tarball size: 188M
- install size: 488M
- The init system used in this rootfs is sysvinit . To boot with systemd, see note 2 below.
- Installed packages: nano, avahi, ntp, busybox-syslogd (log to RAM), htop, isc-dhcp-client, dialog, bzip2, nfs server/client, iperf, ethtool, sysvinit-core, sysvinit, and sysvinit-utils.
- see LED controls in /etc/rc.local, and /etc/init.d/halt
- see some useful aliases in /root/.profile
- root password: root
Download at Dropbox:
Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2
md5:
bf3d29569943875df348fb5ca03b348c
sha256:
4ed5714fdb123cdb40e973f3d0754e91cd199b75a9874018f2b5dc9cfa8ae8bb
Re: Pogoplug 4 uboot update won't boot June 25, 2018 06:53PM |
Registered: 9 years ago Posts: 35 |
Re: Pogoplug 4 uboot update won't boot June 25, 2018 07:51PM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: Pogoplug 4 uboot update won't boot June 25, 2018 09:36PM |
Registered: 9 years ago Posts: 35 |
Re: Pogoplug 4 uboot update won't boot June 25, 2018 10:28PM |
Admin Registered: 13 years ago Posts: 18,495 |