U-Boot 2015.10 for Iomega HMNHDCE
Posted by mari8b
|
Re: U-Boot 2015.10 for Iomega HMNHDCE April 18, 2021 11:53AM |
Registered: 3 years ago Posts: 13 |
> So, try booting with uImage only:
>
Hello bodhi, now there's no way to boot... he continuously gives "Bad Data CRC". I've tried 4 times with no success, even after re-downloading (and checking md5) the whole debian rootfs for 4.4.54:
> If the behavior is the same hang with the above,
> try using a newer uImage such as one in
> linux-5.4.101-oxnas-tld-1.bodhi.tar.bz2.
>
Meanwhile, with 5.4.101 I have the usual behaviour:
Edited 1 time(s). Last edit at 04/18/2021 12:11PM by Miclaud.
>
> setenv usb_set_bootargs 'setenv bootargs > console=ttyS0,115200 root=LABEL=rootfs > rootdelay=10 earlyprintk=serial' > setenv dt_load_dtb 'echo Not loading uInitrd" > setenv dt_load_initrd 'echo Not loading uInitrd' > setenv dt_load_uimage ''echo Loading uImage from > USB; ext2load usb 0:1 $uimage_addr /boot/uImage' > setenv dt_bootm 'echo Booting Debian; bootm > $uimage_addrr' > boot >
Hello bodhi, now there's no way to boot... he continuously gives "Bad Data CRC". I've tried 4 times with no success, even after re-downloading (and checking md5) the whole debian rootfs for 4.4.54:
U-Boot SPL 2013.10-ga72eb8f (Apr 12 2021 - 03:23:10)
Boot device: SATA
Attempting to set PLLA to 800 MHz ...
plla_ctrl0 : 0000030a
plla_ctrl1 : 00400000
plla_ctrl2 : 007f0068
plla_ctrl3 : 00000193
PLLA Set
Bus 0: OK
Device 0:
reading bootargs.bin
reading u-boot.img
reading u-boot.img
U-Boot 2015.10-g5d26bd2 (Apr 12 2021 - 22:17:38 +0800)
OXNAS OX820
DRAM: 128 MiB
NAND: 0 MiB
*** Warning - readenv() failed, using default environment
In: serial
Out: serial
Err: serial
Net: Phy 0 not found
PHY reset timed out
dwmac.40400000
Hit any key to stop autoboot: 10
OX820> setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial'
OX820> setenv dt_load_dtb 'echo Not loading uInitrd'
OX820> setenv dt_load_initrd 'echo Not loading uInitrd'
OX820> setenv dt_load_uimage 'echo Loading.uImage.from.USB ; ext2load usb 0:1 $uimage_addr /boot/uImage'
OX820> setenv dt_bootm 'echo Booting.Debian; bootm $uimage_addr'
OX820> boot
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Reset IDE: Bus 0: OK
Device 0: Model: Hitachi HDT721032SLA380 Firm: ST2OA39D Ser#: STA207MC2K012B
Type: Hard Disk
Supports 48-bit addressing
Capacity: 305245.3 MB = 298.0 GB (625142448 x 512)
Partition Map for USB device 0 -- Partition Type: DOS
Part Start Sector Num Sectors UUID Type
1 2048 15153152 80750a54-01 83
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **
Partition Map for IDE device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00010000 0x0001ffff "boot"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
guid: 8ced04b1-0d4b-4a89-83e5-69686b6ecb4e
loading envs from ide 0 ...
reading /boot/uEnv.txt
** Unable to read file /boot/uEnv.txt **
Loading.uImage.from.USB
4621824 bytes read in 340 ms (13 MiB/s)
Not loading uInitrd
Not loading uInitrd
Booting.Debian
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-4.4.54-oxnas-tld-1
Created: 2017-08-01 4:45:36 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4621760 Bytes = 4.4 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... Bad Data CRC
> If the behavior is the same hang with the above,
> try using a newer uImage such as one in
> linux-5.4.101-oxnas-tld-1.bodhi.tar.bz2.
>
Meanwhile, with 5.4.101 I have the usual behaviour:
U-Boot SPL 2013.10-ga72eb8f (Apr 12 2021 - 03:23:10)
Boot device: SATA
Attempting to set PLLA to 800 MHz ...
plla_ctrl0 : 0000030a
plla_ctrl1 : 00400000
plla_ctrl2 : 007f0068
plla_ctrl3 : 00000193
PLLA Set
Bus 0: OK
Device 0:
reading bootargs.bin
reading u-boot.img
reading u-boot.img
U-Boot 2015.10-g5d26bd2 (Apr 12 2021 - 22:17:38 +0800)
OXNAS OX820
DRAM: 128 MiB
NAND: 0 MiB
*** Warning - readenv() failed, using default environment
In: serial
Out: serial
Err: serial
Net: Phy 0 not found
PHY reset timed out
dwmac.40400000
Hit any key to stop autoboot: 10 0
OX820> setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial'
OX820> setenv dt_load_dtb 'echo Not loading uInitrd'
OX820> setenv dt_load_initrd 'echo Not loading uInitrd'
OX820> setenv dt_load_uimage 'echo Loading.uImage.from.USB ; ext2load usb 0:1 $uimage_addr /boot/uImage'
OX820> setenv dt_bootm 'echo Booting.Debian; bootm $uimage_addr'
OX820> boot
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Reset IDE: Bus 0: OK
Device 0: Model: Hitachi HDT721032SLA380 Firm: ST2OA39D Ser#: STA207MC2K012B
Type: Hard Disk
Supports 48-bit addressing
Capacity: 305245.3 MB = 298.0 GB (625142448 x 512)
Partition Map for USB device 0 -- Partition Type: DOS
Part Start Sector Num Sectors UUID Type
1 2048 15153152 80750a54-01 83
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **
Partition Map for IDE device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00010000 0x0001ffff "boot"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
guid: 8ced04b1-0d4b-4a89-83e5-69686b6ecb4e
loading envs from ide 0 ...
reading /boot/uEnv.txt
** Unable to read file /boot/uEnv.txt **
Loading.uImage.from.USB
EHCI timed out on TD - token=0x40008d80
EHCI timed out on TD - token=0xd8d80
EHCI timed out on TD - token=0x10008d80
EHCI timed out on TD - token=0xd8d80
5509763 bytes read in 21347 ms (252 KiB/s)
Not loading uInitrd
Not loading uInitrd
Booting.Debian
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-5.4.101-oxnas-tld-1
Created: 2021-04-18 16:46:48 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5509699 Bytes = 5.3 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Edited 1 time(s). Last edit at 04/18/2021 12:11PM by Miclaud.
|
Re: U-Boot 2015.10 for Iomega HMNHDCE April 19, 2021 05:36PM |
Admin Registered: 13 years ago Posts: 18,564 |
Miclaud,
> ## Booting kernel from Legacy Image at 60500000
> ...
> Image Name: Linux-5.4.101-oxnas-tld-1
> Created: 2021-04-18 16:46:48 UTC
> Image Type: ARM Linux Kernel Image
> (uncompressed)
> Data Size: 5509699 Bytes = 5.3 MiB
> Load Address: 60008000
> Entry Point: 60008000
> Verifying Checksum ... OK
> Loading Kernel Image ... OK
It looks like the kernel was not even started. Usually we would see
So I don't know if will work at all for this this box.
The behavior is similar to the case when a conficting HW address is being used for the Iomega. So I guess we should look closely at the stock u-boot boot log and compare it with the Pogo V3 log.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> ## Booting kernel from Legacy Image at 60500000
> ...
> Image Name: Linux-5.4.101-oxnas-tld-1
> Created: 2021-04-18 16:46:48 UTC
> Image Type: ARM Linux Kernel Image
> (uncompressed)
> Data Size: 5509699 Bytes = 5.3 MiB
> Load Address: 60008000
> Entry Point: 60008000
> Verifying Checksum ... OK
> Loading Kernel Image ... OK
It looks like the kernel was not even started. Usually we would see
Quote
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
So I don't know if will work at all for this this box.
The behavior is similar to the case when a conficting HW address is being used for the Iomega. So I guess we should look closely at the stock u-boot boot log and compare it with the Pogo V3 log.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: U-Boot 2015.10 for Iomega HMNHDCE April 21, 2021 01:14PM |
Registered: 3 years ago Posts: 13 |
Hi bodhi,
> The behavior is similar to the case when a
> conficting HW address is being used for the
> Iomega. So I guess we should look closely at the
> stock u-boot boot log and compare it with the Pogo
> V3 log.
If it could be of any help, I removed the usb drive and switched the HDD back to the original one with stock u-boot and olderzeus's 2.6 kernel.
Don't worry about udev errors while booting linux. They're due to the fact that I tried to dist-upgrade from squeeze to wheezy but olderzeus's kernel is too old.
Thank you again
> The behavior is similar to the case when a
> conficting HW address is being used for the
> Iomega. So I guess we should look closely at the
> stock u-boot boot log and compare it with the Pogo
> V3 log.
If it could be of any help, I removed the usb drive and switched the HDD back to the original one with stock u-boot and olderzeus's 2.6 kernel.
Don't worry about udev errors while booting linux. They're due to the fact that I tried to dist-upgrade from squeeze to wheezy but olderzeus's kernel is too old.
Thank you again
Stage-1 Bootloader Mon Feb 7 16:35:00 MST 2011
Attempting to set PLLA to 600MHz ...
plla_ctrl0 : 0x0000021A
plla_ctrl1 : 0x00480000
plla_ctrl2 : 0x008F008B
plla_ctrl3 : 0x00000154
PLLA Set
Setup memory, testing
Reading disk 0, Image 0
Sector : 0x0000009A
Hdr len: 0x0001873C
Hdr CRC: 0x9C321E55
OK
Initialising disks
SATA PHY not ready for device 1
Detecting SATA busses:
Bus 0: Found first device OK
Device 0: Model: TOSHIBA MQ01ABD032 Firm: AX001A Ser#: X3UPTGU5T
Type: Hard Disk
Capacity: 131071.9 MB = 127.9 GB (268435455 x 512)
Device 1: not available
Environment successfully read from disk 0 primary image
U-Boot 1.1.2 (Sep 8 2012 - 10:03:04)
U-Boot code: 60D00000 -> 60D1873C BSS: -> 60D1C3CC
RAM Configuration:
Bank #0: 60000000 256 MB
SRAM Configuration:
64KB at 0x50000000
In: serial
Out: serial
Err: serial
Setting Linux mem= boot arg value
IDE read: device 0 block # 288, count 1 ... 1 blocks read: OK
Hit any key to stop autoboot: 3 2 1 0
IDE device 0: Model: TOSHIBA MQ01ABD032 Firm: AX001A Ser#: X3UPTGU5T
Type: Hard Disk
Capacity: 131071.9 MB = 127.9 GB (268435455 x 512)
... is now current device
IDE read: device 0 block # 1290, count 5700 ... 5700 blocks read: OK
IDE read: device 0 block # 16674, count 5700 ... 5700 blocks read: OK
## Booting image at 60500000 ...
Image Name: Linux-2.6.31.14
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2593380 Bytes = 2.5 MB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... Bad Data CRC
Light LED
IDE device 0: Model: TOSHIBA MQ01ABD032 Firm: AX001A Ser#: X3UPTGU5T
Type: Hard Disk
Capacity: 131071.9 MB = 127.9 GB (268435455 x 512)
... is now current device
IDE read: device 0 block # 58344, count 5700 ... 5700 blocks read: OK
IDE read: device 0 block # 16674, count 5700 ... 5700 blocks read: OK
Extinguish LED
## Booting image at 60500000 ...
Image Name: Linux-2.6.31.14
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2593380 Bytes = 2.5 MB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 60800000 ...
Image Name:
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 2652186 Bytes = 2.5 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
Uncompressing Linux.......................................................................................................................................................... done, booting the kernel.
[ 0.000000] Linux version 2.6.31.14 (root@IomegaNAS) (gcc version 4.4.5 (Debian 4.4.5-8) ) #1 SMP Fri Oct 12 22:32:50 CST 2012
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5387f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: Oxsemi NAS
[ 0.000000] 1 memory region
[ 0.000000] Ignoring unrecognised tag 0x00000000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: root=/dev/sda1 console=ttyS0,115200 elevator=cfq mem=256M poweroutage=yes mac_adr=0x00,0xd0,0xb8,0x19,0x81,0x0e
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 256MB = 256MB total
[ 0.000000] Memory: 251904KB available (4452K code, 333K data, 128K init, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:96
[ 0.000000] OX820_RPS_init_irq: interrupts 64 to 96
[ 0.000000] ox820_clocksource_init() Timer 2 running at 390625 Hz
[ 0.010000] Console: colour dummy device 80x30
[ 0.010000] console [ttyS0] enabled
[ 0.020000] Calibrating delay loop... 239.20 BogoMIPS (lpj=1196032)
[ 0.260000] Security Framework initialized
[ 0.260000] Mount-cache hash table entries: 512
[ 0.270000] CPU: Testing write buffer coherency: ok
[ 0.270000] Calibrating local timer... 299.99MHz.
[ 0.340000] CPU1: Booted secondary processor
[ 0.440000] Calibrating delay loop... 239.20 BogoMIPS (lpj=1196032)
[ 0.680000] Brought up 2 CPUs
[ 0.690000] SMP: Total of 2 processors activated (478.41 BogoMIPS).
[ 0.700000] NET: Registered protocol family 16
[ 0.700000] Number of DMA channels = 4, version = 4
[ 0.710000] Reserving a DMA channel for ODRB
[ 0.710000] Allocating 475 SRAM generic DMA descriptors
[ 0.720000] bio: create slab <bio-0> at 0
[ 0.720000] SCSI subsystem initialized
[ 0.730000] usbcore: registered new interface driver usbfs
[ 0.730000] usbcore: registered new interface driver hub
[ 0.740000] usbcore: registered new device driver usb
[ 0.780000] NET: Registered protocol family 2
[ 0.780000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.790000] Switched to NOHz mode on CPU #0
[ 0.790000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.790000] Switched to NOHz mode on CPU #1
[ 0.800000] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.810000] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.810000] TCP reno registered
[ 0.820000] NET: Registered protocol family 1
[ 0.820000] Trying to unpack rootfs image as initramfs...
[ 1.220000] Freeing initrd memory: 2588K
[ 1.220000] Create fragment cache
[ 1.230000] VFS: Disk quotas dquot_6.5.2
[ 1.230000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.240000] fuse init (API version 7.12)
[ 1.240000] JFS: nTxBlock = 1990, nTxLock = 15924
[ 1.250000] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
[ 1.260000] SGI XFS Quota Management subsystem
[ 1.270000] msgmni has been set to 497
[ 1.270000] alg: No test for stdrng (krng)
[ 1.280000] io scheduler noop registered
[ 1.280000] io scheduler anticipatory registered
[ 1.290000] io scheduler deadline registered
[ 1.290000] io scheduler cfq registered (default)
[ 1.300000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 1.310000] serial8250: ttyS0 at MMIO 0x44200000 (irq = 55) is a 16550A
[ 1.320000] brd: module loaded
[ 1.330000] loop: module loaded
[ 1.330000] ox820sata: OX820 sata core.
[ 1.340000] scsi0 : oxnassata
[ 1.340000] scsi1 : oxnassata
[ 1.340000] ata1: SATA max UDMA/133 irq 50
[ 1.350000] ata2: SATA max UDMA/133 irq 50
[ 1.350000] ox820sata: reseting SATA core
[ 1.870000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.930000] ata1.00: ATA-8: TOSHIBA MQ01ABD032, AX001A, max UDMA/100
[ 1.930000] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 1.940000] ata1.00: configured for UDMA/100
[ 1.950000] ox820sata: reseting SATA core
[ 2.660000] ata2: SATA link down (SStatus 0 SControl 300)
[ 2.660000] scsi 0:0:0:0: Direct-Access ATA TOSHIBA MQ01ABD0 AX00 PQ: 0 ANSI: 5
[ 2.670000] tun: Universal TUN/TAP device driver, 1.6
[ 2.670000] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[ 2.670000] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 2.670000] sd 0:0:0:0: [sda] Write Protect is off
[ 2.670000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.700000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 2.710000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.710000] Start USB clocks
[ 2.720000] oxnas-ehci oxnas-ehci.0: OXNAS EHCI Host Controller
[ 2.720000] oxnas-ehci oxnas-ehci.0: new USB bus registered, assigned bus number 1
[ 2.730000] sda:
[ 2.760000] oxnas-ehci oxnas-ehci.0: irq 39, io mem 0x00000000
[ 2.780000] oxnas-ehci oxnas-ehci.0: USB 0.0 started, EHCI 1.00
[ 2.780000] usb usb1: configuration #1 chosen from 1 choice
[ 2.790000] hub 1-0:1.0: USB hub found
[ 2.790000] hub 1-0:1.0: 2 ports detected
[ 2.800000] Initializing USB Mass Storage driver...
[ 2.800000] usbcore: registered new interface driver usb-storage
[ 2.810000] USB Mass Storage support registered.
[ 2.810000] usbcore: registered new interface driver ums-alauda
[ 2.820000] usbcore: registered new interface driver ums-datafab
[ 2.820000] usbcore: registered new interface driver ums-freecom
[ 2.830000] usbcore: registered new interface driver ums-isd200
[ 2.840000] usbcore: registered new interface driver ums-jumpshot
[ 2.840000] usbcore: registered new interface driver ums-sddr09
[ 2.850000] usbcore: registered new interface driver ums-sddr55
[ 2.850000] usbcore: registered new interface driver ums-usbat
[ 2.860000] mice: PS/2 mouse device common for all mice
[ 2.870000] md: linear personality registered for level -1
[ 2.870000] md: raid0 personality registered for level 0
[ 2.880000] md: raid1 personality registered for level 1
[ 2.880000] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 2.890000] input: Mapower Buttons as /devices/virtual/input/input0
[ 2.900000] TCP cubic registered
[ 2.900000] NET: Registered protocol family 17
[ 2.940000] sda1
[ 2.950000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.950000] Freeing init memory: 128K
Loading, please wait...
Start Blinking Power LED
mount: mounting none on /dev failed: No such device
W: devtmpfs not available, falling back to tmpfs for /dev
Begin: Loading essential drivers ... [ 4.080000] OXNAS bit-bash I2C driver initialisation OK
[ 4.130000] rtc-pcf8563 0-0051: chip found, driver version 0.4.3
[ 4.140000] rtc-pcf8563 0-0051: rtc core: registered rtc-pcf8563 as rtc0
done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... USB Device node is /dev/sdb1
Started
/dev/buttons file does not exist creating it
Opened /dev/buttons with fd 3
The Button ID from drive is 2 state is 3
Reset Button is NOT pressed
Checking to see the if the reset button is pressed or not
Warning: old md initialisation script found, getting out of its way...
[ 4.320000] md: md0 stopped.
mdadm: no recogniseable superblock on /dev/sda1
mdadm: /dev/sda1 has no superblock - assembly aborted
done.
Begin: Running /scripts/local-premount ... done.
[ 14.550000] kjournald starting. Commit interval 5 seconds
[ 14.550000] EXT3-fs: mounted filesystem with writeback data mode.
Begin: Running /scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[[36minfo[39;49m] Using makefile-style concurrent boot in runlevel S.
[....] udev requires a kernel >= 2.6.32, not started ...[?25l[?1c7[1G[[31mFAIL[39;49m8[?25h[?0c [31mfailed![39;49m
[?25l[?1c7[1G[[31mFAIL[39;49m8[?25h[?0c [31mfailed![39;49m
[....] Activating swap...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone.
[ 18.450000] EXT3 FS on sda1, internal journal
[....] Cleaning up temporary files... /tmp[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c.
[....] Activating lvm and md swap...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone.
[....] Checking file systems...fsck from util-linux 2.20.1
[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone.
[....] Mounting local filesystems...[?25l[?1c7[1G[[31mFAIL[39;49m8[?25h[?0c[31mfailed.[39;49m
/etc/init.d/mountall.sh: 59: kill: Illegal number: 194 1
[....] Activating swapfile swap...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone.
[....] Cleaning up temporary files...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c.
[....] Setting kernel variables ...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone.
[....] Configuring network interfaces...Cannot find device "eth0"
Failed to bring up eth0.
[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone.
[....] Cleaning up temporary files...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c.
[....] startpar: service(s) returned failure: udev mountall-bootclean.sh mountnfs-bootclean.sh ...[?25l[?1c7[1G[[31mFAIL[39;49m8[?25h[?0c [31mfailed![39;49m
INIT: Entering runlevel: 2
[[36minfo[39;49m] Using makefile-style concurrent boot in runlevel 2.
[....] Starting enhanced syslogd: rsyslogd[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c.
[....] Starting periodic command scheduler: cron[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c.
[....] startpar: service(s) returned failure: rsyslog ...[?25l[?1c7[1G[[31mFAIL[39;49m8[?25h[?0c [31mfailed