Boot Debian from USB on Zyxel NSA310 August 15, 2018 09:34AM |
Registered: 6 years ago Posts: 11 |
U-Boot 2013.07 (Sep 20 2013 - 15:45:03) ZyXEL NSA310 1-Bay Power Media Server SoC: Kirkwood 88F6281_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 PHY reset timed out MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found 3834666 bytes read in 377 ms (9.7 MiB/s) 7245696 bytes read in 434 ms (15.9 MiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.12.1-kirkwood-tld-1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3834602 Bytes = 3.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 00d00000 ... Image Name: initramfs-4.12.1-kirkwood-tld-1 Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7245632 Bytes = 6.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.1-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: ZyXEL NSA310 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] INITRD: 0x00d00000+0x006e9000 overlaps in-use memory region - disabling initrd [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 246440K/262144K available (8192K kernel code, 716K rwdata, 1972K rodata, 1024K init, 288K bss, 15704K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0db3274 ( 717 kB) [ 0.000000] .bss : 0xc0db9b9c - 0xc0e01e60 ( 289 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000007] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000042] Switching to timer-based delay loop, resolution 5ns [ 0.000503] Console: colour dummy device 80x30 [ 0.000537] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.000559] pid_max: default: 32768 minimum: 301 [ 0.000754] Security Framework initialized [ 0.000875] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000894] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001743] CPU: Testing write buffer coherency: ok [ 0.002768] Setting up static identity map for 0x100000 - 0x100058 [ 0.003057] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.006316] devtmpfs: initialized [ 0.011065] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.011092] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.011483] prandom: seed boundary self test passed [ 0.015219] prandom: 100 self tests passed [ 0.015232] pinctrl core: initialized pinctrl subsystem [ 0.016386] NET: Registered protocol family 16 [ 0.016765] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.018372] cpuidle: using governor ladder [ 0.018442] cpuidle: using governor menu [ 0.018835] Feroceon L2: Enabling L2 [ 0.018882] Feroceon L2: Cache support initialised. [ 0.024247] No ATAGs? [ 0.033537] vgaarb: loaded [ 0.033856] SCSI subsystem initialized [ 0.034337] usbcore: registered new interface driver usbfs [ 0.034415] usbcore: registered new interface driver hub [ 0.034498] usbcore: registered new device driver usb [ 0.035576] clocksource: Switched to clocksource orion_clocksource [ 0.124157] VFS: Disk quotas dquot_6.6.0 [ 0.124241] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.134755] NET: Registered protocol family 2 [ 0.135500] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.135539] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.135623] TCP: Hash tables configured (established 2048 bind 2048) [ 0.135714] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.135744] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.135924] NET: Registered protocol family 1 [ 0.136340] RPC: Registered named UNIX socket transport module. [ 0.136353] RPC: Registered udp transport module. [ 0.136360] RPC: Registered tcp transport module. [ 0.136368] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.136679] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.137624] audit: initializing netlink subsys (disabled) [ 0.138031] Initialise system trusted keyrings [ 0.138083] Key type blacklist registered [ 0.138181] audit: type=2000 audit(0.132:1): state=initialized audit_enabled=0 res=1 [ 0.138266] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 0.138335] zbud: loaded [ 0.139316] NFS: Registering the id_resolver key type [ 0.139347] Key type id_resolver registered [ 0.139355] Key type id_legacy registered [ 0.139373] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.139383] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.139576] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.139773] fuse init (API version 7.26) [ 0.140116] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.140317] orangefs_init: module version upstream loaded [ 0.140328] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 2.555584] random: fast init done [ 5.975060] Key type asymmetric registered [ 5.975078] Asymmetric key parser 'x509' registered [ 5.975143] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 5.975155] io scheduler noop registered [ 5.975164] io scheduler deadline registered [ 5.975241] io scheduler cfq registered (default) [ 5.976609] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 5.978514] mvebu-pcie mbus@f1000000:pcie-controller@82000000: PCI host bridge to bus 0000:00 [ 5.978535] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 5.978549] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 5.978563] pci_bus 0000:00: root bus resource [bus 00-ff] [ 5.978889] PCI: bus0: Fast back to back transfers disabled [ 5.978915] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 6.005694] PCI: bus1: Fast back to back transfers disabled [ 6.005904] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 6.005920] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff] [ 6.005939] pci 0000:01:00.0: BAR 6: assigned [mem 0xe0000000-0xe000ffff pref] [ 6.005956] pci 0000:01:00.0: BAR 4: assigned [mem 0xe0010000-0xe0013fff 64bit pref] [ 6.005980] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0014000-0xe0014fff 64bit pref] [ 6.006001] pci 0000:01:00.0: BAR 0: assigned [io 0x10000-0x100ff] [ 6.006017] pci 0000:00:01.0: PCI bridge to [bus 01] [ 6.006031] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff] [ 6.006047] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 6.006142] pcieport 0000:00:01.0: enabling device (0140 -> 0143) [ 6.006667] mv_xor f1060800.xor: Marvell shared XOR driver [ 6.066319] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 6.066543] mv_xor f1060900.xor: Marvell shared XOR driver [ 6.126314] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 6.126764] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 6.128134] console [ttyS0] disabled [ 6.128205] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 6.824166] console [ttyS0] enabled [ 6.836097] loop: module loaded [ 6.839823] sata_mv f1080000.sata: slots 32 ports 2 [ 6.847542] scsi host0: sata_mv [ 6.851149] scsi host1: sata_mv [ 6.854552] ata1: SATA max UDMA/133 irq 32 [ 6.858726] ata2: SATA max UDMA/133 irq 32 [ 6.863633] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1 [ 6.870128] nand: Samsung NAND 128MiB 3,3V 8-bit [ 6.874765] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 6.882399] Scanning device for bad blocks [ 6.906519] Bad eraseblock 207 at 0x0000019e0000 [ 6.989756] 9 ofpart partitions found on MTD device orion_nand [ 6.995635] Creating 9 MTD partitions on "orion_nand": [ 7.000806] 0x000000000000-0x000000100000 : "uboot" [ 7.007047] 0x000000100000-0x000000180000 : "uboot_env" [ 7.013596] 0x000000180000-0x000000200000 : "key_store" [ 7.020211] 0x000000200000-0x000000280000 : "info" [ 7.026230] 0x000000280000-0x000000c80000 : "etc" [ 7.032125] 0x000000c80000-0x000001680000 : "kernel_1" [ 7.038543] 0x000001680000-0x000004640000 : "rootfs1" [ 7.045114] 0x000004640000-0x000005040000 : "kernel_2" [ 7.051623] 0x000005040000-0x000008000000 : "rootfs2" [ 7.059518] libphy: Fixed MDIO Bus: probed [ 7.064487] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.071120] ehci-pci: EHCI PCI platform driver [ 7.075679] ehci-orion: EHCI orion driver [ 7.079922] orion-ehci f1050000.ehci: EHCI Host Controller [ 7.085468] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 7.093487] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 7.125682] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 7.132001] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 7.138875] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.146172] usb usb1: Product: EHCI Host Controller [ 7.151077] usb usb1: Manufacturer: Linux 4.12.1-kirkwood-tld-1 ehci_hcd [ 7.157846] usb usb1: SerialNumber: f1050000.ehci [ 7.163225] hub 1-0:1.0: USB hub found [ 7.167099] hub 1-0:1.0: 1 port detected [ 7.171656] usbcore: registered new interface driver usb-storage [ 7.178091] mousedev: PS/2 mouse device common for all mice [ 7.184261] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 7.191383] i2c /dev entries driver [ 7.198194] hidraw: raw HID events driver (C) Jiri Kosina [ 7.203980] drop_monitor: Initializing network drop monitor service [ 7.210578] NET: Registered protocol family 17 [ 7.215121] Key type dns_resolver registered [ 7.220161] registered taskstats version 1 [ 7.224279] Loading compiled-in X.509 certificates [ 7.229182] zswap: loaded using pool lzo/zbud [ 7.236088] Key type big_key registered [ 7.241823] Key type encrypted registered [ 7.247281] rtc-mv f1010300.rtc: setting system clock to 2018-08-15 14:20:11 UTC (1534342811) [ 7.365627] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 7.376477] ata1.00: ATA-9: WDC WD20EFRX-68AX9N0, 80.00A80, max UDMA/133 [ 7.383212] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 7.392828] ata1.00: configured for UDMA/133 [ 7.407712] scsi 0:0:0:0: Direct-Access ATA WDC WD20EFRX-68A 0A80 PQ: 0 ANSI: 5 [ 7.417031] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB) [ 7.424818] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 7.430667] sd 0:0:0:0: [sda] Write Protect is off [ 7.435696] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 7.459386] sda: sda1 sda2 [ 7.463940] sd 0:0:0:0: [sda] Attached SCSI disk [ 7.525613] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 7.717372] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 7.724135] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 7.731360] usb 1-1: Product: USB2.0 Hub [ 7.736335] hub 1-1:1.0: USB hub found [ 7.740496] hub 1-1:1.0: 4 ports detected [ 7.760423] ata2: SATA link down (SStatus 0 SControl F300) [ 7.776759] EXT4-fs (sda1): couldn't mount as ext3 due to feature incompatibilities [ 7.799433] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 7.807289] VFS: Mounted root (ext4 filesystem) readonly on device 8:1. [ 7.826817] devtmpfs: mounted [ 7.832688] Freeing unused kernel memory: 1024K INIT: version 2.88 booting [ 8.065617] usb 1-1.3: new high-speed USB device number 3 using orion-ehci [ 8.221123] usb 1-1.3: New USB device found, idVendor=125f, idProduct=db8a [ 8.228170] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 8.239775] usb 1-1.3: Product: ADATA USB Flash Drive [ 8.245459] usb 1-1.3: Manufacturer: ADATA [ 8.253473] usb 1-1.3: SerialNumber: 27B221117003017D [ 8.260598] usb-storage 1-1.3:1.0: USB Mass Storage device detected [ 8.269821] scsi host2: usb-storage 1-1.3:1.0 [info] Using makefile-style concurrent boot in runlevel S. ERROR: could not open /proc/stat: No such file or directory findfs: unable to resolve 'LABEL=rootfs' [....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232 . ok [....] Synthesizing the initial hotplug events...[ 9.452620] scsi 2:0:0:0: Direct-Access ADATA USB Flash Drive 1100 PQ: 0 ANSI: 6 [ 9.482947] sd 2:0:0:0: [sdb] 30310400 512-byte logical blocks: (15.5 GB/14.5 GiB) [ ok 9.502561] sd 2:0:0:0: [sdb] Write Protect is off [ 9.521600] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA done. [ 9.550801] sdb: sdb1 [ 9.557172] sd 2:0:0:0: [sdb] Attached SCSI removable disk [ 9.564523] input: gpio_keys as /devices/platform/gpio_keys/input/input0 [....] Waiting for /dev to be fully populated...[ 9.867845] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 9.873545] r8169 0000:01:00.0: enabling device (0140 -> 0143) [ 9.899764] hwmon_vid: Unknown VRM version of your CPU [ 9.899791] adt7475 0-002e: hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info(). [ 9.899958] adt7475 0-002e: ADT7476 device, revision 1 [ 9.899966] adt7475 0-002e: Optional features: in0 in4 fan4 pwm2 vid [ 9.917666] orion_wdt: Initial timeout 21 sec [ 10.019014] marvell-cesa f1030000.crypto: CESA device successfully registered [ 10.038376] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 10.038597] sd 2:0:0:0: Attached scsi generic sg1 type 0 [ 10.045389] usbcore: registered new interface driver uas [ 10.286852] r8169 0000:01:00.0 eth0: RTL8168d/8111d at 0xd0dbe000, 00:00:00:00:00:30, XID 083000c0 IRQ 33 [ 10.338852] r8169 0000:01:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 10.634048] r8169 0000:01:00.0 enp1s0: renamed from eth0 done. [ ok ] Setting hostname to 'debian'...done. [ ok ] Activating swap:. [ 11.812878] EXT4-fs (sda1): re-mounted. Opts: (null) [....] Will now check root file system:fsck from util-linux 2.29.2 [/sbin/fsck.ext4 (1) -- /] fsck.ext4 -y -C0 /run/rootdev e2fsck 1.43.4 (31-Jan-2017) rootfs: clean, 14480/196608 files, 154801/786432 blocks . ok [ 12.035717] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ ok ] Will now activate lvm and md swap:done. [info] Will now check all file systems. fsck from util-linux 2.29.2 Checking all file systems. LABEL=rootfs is not mounted [/sbin/fsck.ext4 (1) -- /] fsck.ext4 -y -C0 /dev/sdb1 e2fsck 1.43.4 (31-Jan-2017) rootfs: clean, 14456/948416 files, 191552/3788544 blocks [ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.. [....] Cleaning [ 13.392668] random: crng init done [ ok mporary files...[....] Cleaning /tmp...done. [ ok . [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables...done. [ ok ] Initializing random number generator...done. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5 Copyright 2004-2016 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Cannot find device "eth0" Failed to get interface index: No such device If you think you have received this message due to a bug rather than a configuration issue please read the section on submitting bugs on either our web page at www.isc.org or in the README file before submitting a bug. These pages explain the proper process and the information we find helpful for debugging.. exiting. ifup: failed to bring up eth0 failed. [ 15.275931] NET: Registered protocol family 10 [ 15.283520] Segment Routing with IPv6 [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1223 (syslogd) . ok [ ok ] Starting system message bus: dbus. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [ ok ] Starting OpenBSD Secure Shell server: sshd. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1226 (klogd) . ok [ ok ] Running local boot scripts (/etc/rc.local). Debian GNU/Linux 9 debian ttyS0 debian login: root
NSA310> printenv CONTRY_TYPE=FF FEATURE_BIT=00 MODEL_ID=A203 PRODUCT_NAME=NSA-310 VENDOR_NAME=ZyXEL Communications Corp. baudrate=115200 bootargs=console=ttyS0,115200 root=/dev/sda1 bootcmd=usb reset;ext4load usb 0:1 0x800000 /boot/uImage;ext4load usb 0:1 0xd00000 /boot/uInitrd;bootm 0x800000 0xd00000 bootdelay=3 ethact=egiga0 ethaddr=cc:5d:4e:c9:f8:f6 kernel_addr=480000 mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) nandEcc=1bit nandEnvBase=100000 stderr=serial stdin=serial stdout=serial Environment size: 686/131068 bytes
root@debian:~# cat /etc/fw_env.config # Configuration file for fw_(printenv/saveenv) utility. # Up to two entries are valid, in this case the redundant # environment sector is assumed present. # Notice, that the "Number of sectors" is ignored on NOR. # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd0 0xc0000 0x20000 0x20000
root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 00100000 00020000 "uboot" mtd1: 00080000 00020000 "uboot_env" mtd2: 00080000 00020000 "key_store" mtd3: 00080000 00020000 "info" mtd4: 00a00000 00020000 "etc" mtd5: 00a00000 00020000 "kernel_1" mtd6: 02fc0000 00020000 "rootfs1" mtd7: 00a00000 00020000 "kernel_2" mtd8: 02fc0000 00020000 "rootfs2"
root@debian:~# ls -all /dev/mt* crw------- 1 root root 90, 0 Aug 15 07:34 /dev/mtd0 crw------- 1 root root 90, 1 Aug 15 07:34 /dev/mtd0ro crw------- 1 root root 90, 2 Aug 15 07:34 /dev/mtd1 crw------- 1 root root 90, 3 Aug 15 07:34 /dev/mtd1ro crw------- 1 root root 90, 4 Aug 15 07:34 /dev/mtd2 crw------- 1 root root 90, 5 Aug 15 07:34 /dev/mtd2ro crw------- 1 root root 90, 6 Aug 15 07:34 /dev/mtd3 crw------- 1 root root 90, 7 Aug 15 07:34 /dev/mtd3ro crw------- 1 root root 90, 8 Aug 15 07:34 /dev/mtd4 crw------- 1 root root 90, 9 Aug 15 07:34 /dev/mtd4ro crw------- 1 root root 90, 10 Aug 15 07:34 /dev/mtd5 crw------- 1 root root 90, 11 Aug 15 07:34 /dev/mtd5ro crw------- 1 root root 90, 12 Aug 15 07:34 /dev/mtd6 crw------- 1 root root 90, 13 Aug 15 07:34 /dev/mtd6ro crw------- 1 root root 90, 14 Aug 15 07:34 /dev/mtd7 crw------- 1 root root 90, 15 Aug 15 07:34 /dev/mtd7ro crw------- 1 root root 90, 16 Aug 15 07:34 /dev/mtd8 crw------- 1 root root 90, 17 Aug 15 07:34 /dev/mtd8ro brw-rw---- 1 root disk 31, 0 Aug 15 07:34 /dev/mtdblock0 brw-rw---- 1 root disk 31, 1 Aug 15 07:34 /dev/mtdblock1 brw-rw---- 1 root disk 31, 2 Aug 15 07:34 /dev/mtdblock2 brw-rw---- 1 root disk 31, 3 Aug 15 07:34 /dev/mtdblock3 brw-rw---- 1 root disk 31, 4 Aug 15 07:34 /dev/mtdblock4 brw-rw---- 1 root disk 31, 5 Aug 15 07:34 /dev/mtdblock5 brw-rw---- 1 root disk 31, 6 Aug 15 07:34 /dev/mtdblock6 brw-rw---- 1 root disk 31, 7 Aug 15 07:34 /dev/mtdblock7 brw-rw---- 1 root disk 31, 8 Aug 15 07:34 /dev/mtdblock8
Re: Boot Debian from USB on Zyxel NSA310 August 15, 2018 11:58PM |
Admin Registered: 14 years ago Posts: 19,291 |
Quote
Now I can boot Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2 (uImage and uinitrd read from USB, the rest read from HDD), but mtd0 partition is read only. How can I mount it writeable?
Re: Boot Debian from USB on Zyxel NSA310 August 16, 2018 04:17AM |
Registered: 6 years ago Posts: 11 |
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5 Copyright 2004-2016 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Cannot find device "eth0" Failed to get interface index: No such device If you think you have received this message due to a bug rather than a configuration issue please read the section on submitting bugs on either our web page at www.isc.org or in the README file before submitting a bug. These pages explain the proper process and the information we find helpful for debugging.. exiting. ifup: failed to bring up eth0 failed.
root@debian:~# fw_printenv ethaddr Warning: Bad CRC, using default environment ethaddr=00:00:11:22:33:44
root@debian:~# dmesg | grep -i 'bad' [ 6.882391] Scanning device for bad blocks [ 6.906517] Bad eraseblock 207 at 0x0000019e0000
ide reset;ext2load ide 0:1 0x800000 /home/uboot.2017.07-tld-1.nsa310.mtd0.kwb nand erase 0x0 0x80000 nand write.e 0x800000 0x0 0x80000 reset
Re: Boot Debian from USB on Zyxel NSA310 August 16, 2018 05:03AM |
Registered: 6 years ago Posts: 11 |
[ 10.634048] r8169 0000:01:00.0 enp1s0: renamed from eth0So I modified /etc/network/interfaces and everything's ok now...
Re: Boot Debian from USB on Zyxel NSA310 August 16, 2018 05:07AM |
Admin Registered: 14 years ago Posts: 19,291 |
> ide reset;ext2load ide 0:1 0x800000 > /home/uboot.2017.07-tld-1.nsa310.mtd0.kwb > nand erase 0x0 0x80000 > nand write.e 0x800000 0x0 0x80000 > reset >
Quote
https://forum.doozan.com/read.php?3,12381
UART Booting: If possible, try to test this boot image with UART booting before flashing to NAND. See davygravy's UART booting using kwboot instruction here in this thread. The latest u-boot image released here should be used for UART booting, if your box is the type that supports it (these do not: Dockstar, Pogo E02, iConnect).
Re: Boot Debian from USB on Zyxel NSA310 August 16, 2018 06:04AM |
Admin Registered: 14 years ago Posts: 19,291 |