Bootloader fail September 28, 2018 01:17PM |
Registered: 9 years ago Posts: 4 |
U-Boot 2017.07-tld-1 (Oct 24 2017 - 22:32:36 -0700) Seagate FreeAgent DockStar SoC: Kirkwood 88F6281_A0 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 88E1116 Initialized on egiga0 ## Error: "if_netconsole" not defined ## Error: "if_netconsole" not defined ## Error: "if_netconsole" not defined ## Error: "if_netconsole" not defined ## Error: "if_netconsole" not defined Hit any key to stop autoboot: 3 2 1 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found ** Bad device usb 0 ** ** Bad device usb 0 ** ubi0: attaching mtd1 ubi0: scanning is finished ubi0: attached mtd1 (name "mtd=3", size 219 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512 ubi0: VID header offset: 512 (aligned 512), data offset: 2048 ubi0: good PEBs: 1749, bad PEBs: 3, corrupted PEBs: 0 ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 1/1, WL threshold: 4096, image sequence number: 0 ubi0: available PEBs: 1708, total reserved PEBs: 41, PEBs reserved for bad PEB handling: 37 Error reading superblock on volume 'rootfs' errno=-22! ubifsmount - mount UBIFS volume Usage: ubifsmount <volume-name> - mount 'volume-name' volume ** Bad device usb 0 ** ** Bad device usb 1 ** ** Bad device usb 2 ** ** Bad device usb 3 ** ** Bad device usb 0 ** ** Bad device usb 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! stopping USB.. ### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000 Scanning JFFS2 FS: . read_nand_cached: error reading nand off 0x5c1000 size 8192 bytes . . . . . . read_nand_cached: error reading nand off 0x12b7200 size 8192 bytes . . done. read_nand_cached: error reading nand off 0x5c1000 size 8192 bytes read_nand_cached: error reading nand off 0x12b7200 size 8192 bytes ### JFFS2 load complete: 524288 bytes loaded to 0x800000 ## Starting application at 0x00800200 ... U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:256 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: REDSTONE:1.0 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 3 2 1 0 NAND read: device 0 offset 0x100000, size 0x300000 Reading data from 0x100000 -- 0% complete. Reading data from 0x107800 -- 1% complete. Reading data from 0x10f000 -- 2% complete. Reading data from 0x117000 -- 3% complete. Reading data from 0x11e800 -- 4% complete. Reading data from 0x126000 -- 5% complete. Reading data from 0x12e000 -- 6% complete. Reading data from 0x135800 -- 7% complete. Reading data from 0x13d000 -- 8% complete. Reading data from 0x145000 -- 9% complete. Reading data from 0x14c800 -- 10% complete. Reading data from 0x154000 -- 11% complete. Reading data from 0x15c000 -- 12% complete. Reading data from 0x163800 -- 13% complete. Reading data from 0x16b800 -- 14% complete. Reading data from 0x173000 -- 15% complete. Reading data from 0x17a800 -- 16% complete. Reading data from 0x182800 -- 17% complete. Reading data from 0x18a000 -- 18% complete. Reading data from 0x191800 -- 19% complete. Reading data from 0x199800 -- 20% complete. Reading data from 0x1a1000 -- 21% complete. Reading data from 0x1a8800 -- 22% complete. Reading data from 0x1b0800 -- 23% complete. Reading data from 0x1b8000 -- 24% complete. Reading data from 0x1bf800 -- 25% complete. Reading data from 0x1c7800 -- 26% complete. Reading data from 0x1cf000 -- 27% complete. Reading data from 0x1d7000 -- 28% complete. Reading data from 0x1de800 -- 29% complete. Reading data from 0x1e6000 -- 30% complete. Reading data from 0x1ee000 -- 31% complete. Reading data from 0x1f5800 -- 32% complete. Reading data from 0x1fd000 -- 33% complete. Reading data from 0x205000 -- 34% complete. Reading data from 0x20c800 -- 35% complete. Reading data from 0x214000 -- 36% complete. Reading data from 0x21c000 -- 37% complete. Reading data from 0x223800 -- 38% complete. Reading data from 0x22b800 -- 39% complete. Reading data from 0x233000 -- 40% complete. Reading data from 0x23a800 -- 41% complete. Reading data from 0x242800 -- 42% complete. Reading data from 0x24a000 -- 43% complete. Reading data from 0x251800 -- 44% complete. Reading data from 0x259800 -- 45% complete. Reading data from 0x261000 -- 46% complete. Reading data from 0x268800 -- 47% complete. Reading data from 0x270800 -- 48% complete. Reading data from 0x278000 -- 49% complete. Reading data from 0x27f800 -- 50% complete. Reading data from 0x287800 -- 51% complete. Reading data from 0x28f000 -- 52% complete. Reading data from 0x297000 -- 53% complete. Reading data from 0x29e800 -- 54% complete. Reading data from 0x2a6000 -- 55% complete. Reading data from 0x2ae000 -- 56% complete. Reading data from 0x2b5800 -- 57% complete. Reading data from 0x2bd000 -- 58% complete. Reading data from 0x2c5000 -- 59% complete. Reading data from 0x2cc800 -- 60% complete. Reading data from 0x2d4000 -- 61% complete. Reading data from 0x2dc000 -- 62% complete. Reading data from 0x2e3800 -- 63% complete. Reading data from 0x2eb800 -- 64% complete. Reading data from 0x2f3000 -- 65% complete. Reading data from 0x2fa800 -- 66% complete. Reading data from 0x302800 -- 67% complete. Reading data from 0x30a000 -- 68% complete. Reading data from 0x311800 -- 69% complete. Reading data from 0x319800 -- 70% complete. Reading data from 0x321000 -- 71% complete. Reading data from 0x328800 -- 72% complete. Reading data from 0x330800 -- 73% complete. Reading data from 0x338000 -- 74% complete. Reading data from 0x33f800 -- 75% complete. Reading data from 0x347800 -- 76% complete. Reading data from 0x34f000 -- 77% complete. Reading data from 0x357000 -- 78% complete. Reading data from 0x35e800 -- 79% complete. Reading data from 0x366000 -- 80% complete. Reading data from 0x36e000 -- 81% complete. Reading data from 0x375800 -- 82% complete. Reading data from 0x37d000 -- 83% complete. Reading data from 0x385000 -- 84% complete. Reading data from 0x38c800 -- 85% complete. Reading data from 0x394000 -- 86% complete. Reading data from 0x39c000 -- 87% complete. Reading data from 0x3a3800 -- 88% complete. Reading data from 0x3ab800 -- 89% complete. Reading data from 0x3b3000 -- 90% complete. Reading data from 0x3ba800 -- 91% complete. Reading data from 0x3c2800 -- 92% complete. Reading data from 0x3ca000 -- 93% complete. Reading data from 0x3d1800 -- 94% complete. Reading data from 0x3d9800 -- 95% complete. Reading data from 0x3e1000 -- 96% complete. Reading data from 0x3e8800 -- 97% complete. Reading data from 0x3f0800 -- 98% complete. Reading data from 0x3f8000 -- 99% complete. Reading data from 0x3ff800 -- 100% complete. 3145728 bytes read: OK ## Booting image at 00800000 ... Image Name: Linux-2.6.22.18 Created: 2010-10-19 23:05:02 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1979140 Bytes = 1.9 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux............................................................................................................................ done, booting the kernel. [ 0.000000] Linux version 2.6.22.18 (bdietrich@buildman) (gcc version 4.2.1) #81 Tue Oct 19 16:05:00 PDT 2010 [ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177 [ 0.000000] Machine: Feroceon-KW [ 0.000000] Using UBoot passing parameters structure [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] CPU0: D VIVT write-back cache [ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] Built 1 zonelists. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro [ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes) [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 128MB 0MB 0MB 0MB = 128MB total [ 0.000000] Memory: 125824KB available (3592K code, 253K data, 124K init) [ 0.240000] Mount-cache hash table entries: 512 [ 0.240000] CPU: Testing write buffer coherency: ok [ 0.240000] NET: Registered protocol family 16 [ 0.240000] [ 0.240000] CPU Interface [ 0.240000] ------------- [ 0.240000] SDRAM_CS0 ....base 00000000, size 128MB [ 0.240000] SDRAM_CS1 ....disable [ 0.240000] SDRAM_CS2 ....disable [ 0.240000] SDRAM_CS3 ....disable [ 0.240000] PEX0_MEM ....base e8000000, size 128MB [ 0.240000] PEX0_IO ....base f2000000, size 1MB [ 0.240000] INTER_REGS ....base f1000000, size 1MB [ 0.240000] NFLASH_CS ....base fa000000, size 2MB [ 0.240000] SPI_CS ....base f4000000, size 16MB [ 0.240000] BOOT_ROM_CS ....no such [ 0.240000] DEV_BOOTCS ....no such [ 0.240000] CRYPT_ENG ....base f0000000, size 2MB [ 0.240000] [ 0.240000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21_with_rx_desc_tuned)-- SHEEVA PLUG Soc: 88F6281 A0 LE [ 0.240000] [ 0.240000] Detected Tclk 200000000 and SysClk 400000000 [ 0.240000] MV Buttons Device Load [ 0.240000] Marvell USB EHCI Host controller #0: c0539600 [ 0.740000] PEX0 interface detected no Link. [ 0.740000] PCI: bus0: Fast back to back transfers enabled [ 0.740000] SCSI subsystem initialized [ 0.740000] usbcore: registered new interface driver usbfs [ 0.740000] usbcore: registered new interface driver hub [ 0.740000] usbcore: registered new device driver usb [ 0.740000] NET: Registered protocol family 2 [ 0.750000] Time: kw_clocksource clocksource has been installed. [ 0.840000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.840000] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.840000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.840000] TCP: Hash tables configured (established 4096 bind 4096) [ 0.840000] TCP reno registered [ 0.870000] RTC has been updated!!! [ 0.870000] RTC registered [ 0.870000] Use the XOR engines (acceleration) for enhancing the following functions: [ 0.870000] o RAID 5 Xor calculation [ 0.870000] o kernel memcpy [ 0.870000] o kenrel memzero [ 0.870000] Number of XOR engines to use: 4 [ 0.870000] cesadev_init(c00117b0) [ 0.870000] mvCesaInit: sessions=640, queue=64, pSram=f0000000 [ 0.870000] MV Buttons Driver Load [ 0.870000] squashfs: version 3.3 (2007/10/31) Phillip Lougher [ 0.870000] squashfs: LZMA suppport for slax.org by jro [ 0.870000] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.870000] io scheduler noop registered [ 0.870000] io scheduler anticipatory registered (default) [ 0.890000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [ 0.890000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A [ 0.900000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize [ 0.910000] Loading Marvell Ethernet Driver: [ 0.910000] o Cached descriptors in DRAM [ 0.910000] o DRAM SW cache-coherency [ 0.920000] o Single RX Queue support - ETH_DEF_RXQ=0 [ 0.920000] o Single TX Queue support - ETH_DEF_TXQ=0 [ 0.930000] o TCP segmentation offload enabled [ 0.930000] o Receive checksum offload enabled [ 0.940000] o Transmit checksum offload enabled [ 0.940000] o Network Fast Processing (Routing) supported [ 0.950000] o Driver ERROR statistics enabled [ 0.950000] o Driver INFO statistics enabled [ 0.960000] o Proc tool API enabled [ 0.960000] o Rx descripors: q0=128 [ 0.960000] o Tx descripors: q0=532 [ 0.970000] o Loading network interface(s): [ 0.970000] o eth0, ifindex = 1, GbE port = 0 [ 0.980000] o eth1, ifindex = 2, GbE port = 1 [ 0.990000] [ 0.990000] mvFpRuleDb (c7ed4000): 1024 entries, 4096 bytes [ 0.990000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI [ 1.000000] Copyright (c) 1999-2006 Intel Corporation. [ 1.010000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI [ 1.010000] e100: Copyright(c) 1999-2006 Intel Corporation [ 1.020000] [ 1.020000] Warning Sata is Powered Off [ 1.020000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ [ 1.030000] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit) [ 1.040000] Scanning device for bad blocks [ 1.060000] Bad eraseblock 416 at 0x03400000 [ 1.080000] Bad eraseblock 666 at 0x05340000 [ 1.140000] Bad eraseblock 1788 at 0x0df80000 [ 1.160000] Using static partition definition [ 1.160000] Creating 4 MTD partitions on "nand_mtd": [ 1.160000] 0x00000000-0x00100000 : "u-boot" [ 1.170000] 0x00100000-0x00500000 : "uImage" [ 1.170000] 0x00500000-0x02500000 : "root" [ 1.180000] 0x02500000-0x10000000 : "data" [ 1.180000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI [ 1.190000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 [ 1.230000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 [ 1.250000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 1.250000] usb usb1: configuration #1 chosen from 1 choice [ 1.260000] hub 1-0:1.0: USB hub found [ 1.260000] hub 1-0:1.0: 1 port detected [ 1.380000] USB Universal Host Controller Interface driver v3.0 [ 1.660000] usb 1-1: new high speed USB device using ehci_marvell and address 2 [ 1.810000] usb 1-1: configuration #1 chosen from 1 choice [ 1.810000] hub 1-1:1.0: USB hub found [ 1.820000] hub 1-1:1.0: 4 ports detected [ 1.930000] usbcore: registered new interface driver usblp [ 1.930000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver [ 1.940000] Initializing USB Mass Storage driver... [ 1.940000] usbcore: registered new interface driver usb-storage [ 1.950000] USB Mass Storage support registered. [ 1.960000] mice: PS/2 mouse device common for all mice [ 1.960000] i2c /dev entries driver [ 1.960000] Linux telephony interface: v1.00 [ 1.970000] md: linear personality registered for level -1 [ 1.970000] md: raid0 personality registered for level 0 [ 1.980000] md: raid1 personality registered for level 1 [ 2.150000] raid6: int32x1 97 MB/s [ 2.320000] raid6: int32x2 114 MB/s [ 2.490000] raid6: int32x4 122 MB/s [ 2.660000] raid6: int32x8 110 MB/s [ 2.660000] raid6: using algorithm int32x4 (122 MB/s) [ 2.660000] md: raid6 personality registered for level 6 [ 2.670000] md: raid5 personality registered for level 5 [ 2.670000] md: raid4 personality registered for level 4 [ 2.680000] raid5: measuring checksumming speed [ 2.730000] arm4regs : 1084.000 MB/sec [ 2.780000] 8regs : 754.800 MB/sec [ 2.830000] 32regs : 900.000 MB/sec [ 2.830000] raid5: using function: arm4regs (1084.000 MB/sec) [ 2.840000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com [ 2.840000] dm_crypt using the OCF package. [ 2.850000] sdhci: Secure Digital Host Controller Interface driver [ 2.850000] sdhci: Copyright(c) Pierre Ossman [ 2.860000] usbcore: registered new interface driver usbhid [ 2.860000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 2.870000] TCP cubic registered [ 2.870000] NET: Registered protocol family 1 [ 2.880000] NET: Registered protocol family 17 [ 2.880000] md: Autodetecting RAID arrays. [ 2.890000] md: autorun ... [ 2.890000] md: ... autorun DONE. [ 7.500000] Empty flash at 0x00de8e44 ends at 0x00de9000 [ 11.690000] VFS: Mounted root (jffs2 filesystem) readonly. [ 11.700000] Freeing init memory: 124K init started: BusyBox v1.7.0 (2008-02-26 19:25:17 IST) starting pid 267, tty '': '/etc/init.d/rcS' [ 13.820000] eth0: started udhcpc (v1.7.0) started HWADDR 00 0x10 0x75 0x1a 0xb2 0xf6 PIP0 178 PIP1 246 cat: can't open '/etc/resolv.conf': No such file or directory route: SIOCDELRT: No such process grep: /etc/resolv.conf: No such file or directory Sending discover... Sending discover... Sending discover... HWADDR 00 0x10 0x75 0x1a 0xb2 0xf6 PIP0 178 PIP1 246 No lease, forking to background starting pid 372, tty '': '/bin/sh' -sh-3.2# -sh-3.2#
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700) Pogo E02 SoC: Kirkwood 88F6281_A0 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 10 9 8 7 6 5 4 3 2 1 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Unknown command 'ide' - try 'help' Unknown command 'mmc' - try 'help' ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... ** Bad device usb 0 ** Unknown command 'ide' - try 'help' Unknown command 'mmc' - try 'help' running scan_disk ... Scan device usb device usb 0:1 ** Bad device usb 0 ** device usb 1:1 ** Bad device usb 1 ** device usb 2:1 ** Bad device usb 2 ** device usb 3:1 ** Bad device usb 3 ** Scan device ide Unknown command 'ide' - try 'help' device ide 0:1 ** Bad device ide 0 ** device ide 1:1 ** Bad device ide 1 ** device ide 2:1 ** Bad device ide 2 ** device ide 3:1 ** Bad device ide 3 ** Scan device mmc Unknown command 'mmc' - try 'help' device mmc 0:1 ** Bad device mmc 0 ** device mmc 1:1 ** Bad device mmc 1 ** device mmc 2:1 ** Bad device mmc 2 ** device mmc 3:1 ** Bad device mmc 3 ** loading uImage ... ** Bad device usb 0 ** loading uInitrd ... ** Bad device usb 0 ** loading DTB /boot/dts/kirkwood-pogo_e02.dtb ... ** Bad device usb 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! PogoE02> ls -l ** No device specified ** PogoE02>
Re: Bootloader fail September 29, 2018 02:40AM |
Admin Registered: 13 years ago Posts: 18,564 |
printenvPlease post the entire serial console log here.
Re: Bootloader fail September 29, 2018 08:00AM |
Registered: 9 years ago Posts: 4 |
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700) Pogo E02 SoC: Kirkwood 88F6281_A0 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 10 9 8 7 6 0 PogoE02> printenv arcNumber=3542 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-pogo_e02.dtb ethact=egiga0 ethaddr=00:25:31:00:c5:46 if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 machid=dd6 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_ready_retry=15 Environment size: 2858/131068 bytes PogoE02>
Re: Bootloader fail September 29, 2018 04:57PM |
Admin Registered: 13 years ago Posts: 18,564 |
Re: Bootloader fail September 29, 2018 07:10PM |
Registered: 9 years ago Posts: 4 |
U-Boot 2017.07-tld-1 (Oct 24 2017 - 22:32:36 -0700) Seagate FreeAgent DockStar SoC: Kirkwood 88F6281_A0 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 88E1116 Initialized on egiga0 ## Error: "if_netconsole" not defined ## Error: "if_netconsole" not defined ## Error: "if_netconsole" not defined ## Error: "if_netconsole" not defined ## Error: "if_netconsole" not defined Hit any key to stop autoboot: 3 0 DockStar> printenv arcNumber=2998 baudrate=115200 bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset bootdelay=3 console=ttyS0,115200 ethact=egiga0 ethaddr=00:10:75:1A:B2:F6 force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi ipaddr=192.168.55.150 led_error=orange blinking led_exit=green off led_init=green blinking mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) nc_ready=0 partition=nand0,2 pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi preboot=run preboot_nc preboot_nc=setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi rescue_installed=0 rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params serverip=192.168.55.121 stderr=serial stdin=serial stdout=serial ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi ubifs_mtd=3 ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot usb_device=0:1 usb_init=run usb_scan usb_root=/dev/sda1 usb_rootdelay=10 usb_rootfstype=ext3 usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done usb_scan_1=usb=0:1 dev=sda1 usb_scan_2=usb=1:1 dev=sdb1 usb_scan_3=usb=2:1 dev=sdc1 usb_scan_4=usb=3:1 dev=sdd1 usb_scan_list=1 2 3 4 usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params Environment size: 2613/131068 bytes DockStar>
Re: Bootloader fail September 29, 2018 07:47PM |
Admin Registered: 13 years ago Posts: 18,564 |
setenv pogo_bootcmd 'if fsload uboot-original-mtd0.kwb; then go 0x800200; fi' setenv bootcmd_exec 'if run load_uimage; then; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi; fi' setenv bootcmd 'run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; run pogo_bootcmd' boot
Re: Bootloader fail September 29, 2018 08:27PM |
Registered: 9 years ago Posts: 4 |