Hi,
I did the DEBIAN installation on a USB stick like described by Jeff in the tutorial. But now my goflex net does not boot any more. Not form USB and not original firmware. I did a connection with the netconsole and have the following output:
#################################################
U-Boot 2010.09 (Feb 16 2011 - 18:42:02)
UBIT v0.6 by Jeff Doozan and Peter Carmichael
Hit any key to stop autoboot: 0
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:fast", error -19
Error reading superblock on volume 'ubi:fast'!
UBIFS not mounted, use ubifs mount to mount volume first!
** Block device usb 0 not supported
** Block device usb 0 not supported
** Invalid boot device **
** Invalid boot device **
** Block device usb 1 not supported
** Block device usb 1 not supported
** Invalid boot device **
** Invalid boot device **
** Block device usb 2 not supported
** Block device usb 2 not supported
** Invalid boot device **
** Invalid boot device **
** Block device usb 3 not supported
** Block device usb 3 not supported
** Invalid boot device **
** Invalid boot device **
Reset IDE: Bus 0: not available Bus 1: not available
** Bad partition 1 **
** Bad partition 1 **
No Powersaving mode 7F
Error (no IRQ) dev 0 blk 0: status 0x7f
** Can't read from device 0 **
** Unable to use ide 0:1 for fatload **
No Powersaving mode 7F
Error (no IRQ) dev 0 blk 0: status 0x7f
** Can't read from device 0 **
** Unable to use ide 0:1 for fatload **
** Bad partition 1 **
** Bad partition 1 **
No Powersaving mode 7F
Error (no IRQ) dev 1 blk 0: status 0x7f
** Can't read from device 1 **
** Unable to use ide 1:1 for fatload **
No Powersaving mode 7F
Error (no IRQ) dev 1 blk 0: status 0x7f
** Can't read from device 1 **
** Unable to use ide 1:1 for fatload **
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:ramdisk", error -19
Error reading superblock on volume 'ubi:ramdisk'!
UBIFS not mounted, use ubifs mount to mount volume first!
Marvell>> usb start
usb start
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 4 USB Device(s) found
scanning bus for storage devices... error in inquiry
1 Storage Device(s) found
Marvell>> usb tree
usb tree
Device Tree:
1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Hub (480 Mb/s, 100mA)
| USB 2.0 Hub
|
+-3 Mass Storage (480 Mb/s, 200mA)
| SanDisk Cruzer Blade 20060165311DAA61395E
|
+-4 Mass Storage (480 Mb/s, 200mA)
PNY Technologies USB 2.0 FD AAB91B830000147
################################
The printenv shows the following:
Marvell>> printenv
printenv
bootcmd=run fast_boot; run usb_boot; run hd_boot; run ubi_boot
baudrate=115200
ide_start=ide reset
ubi_start=ubi part root
usb_start=usb start
nc_test=ping $ncip
nc_start=setenv stdin nc; setenv stdout nc; setenv stderr nc; version
silent_boot=run silent_rd ubi_args ubi_fallback
fast_boot=run fast_rd ubi_args ubi_fallback
usb_boot=for scan in 0 1 2 3; do run usb_args_$scan ext2_kern ext2_boot; run ext
2_rd ubi_fallback; run fat_kern fat_boot; run fat_rd ubi_fallback;done
usb_args_0=boot_dev='usb 0:1'; dev_args='root=/dev/sda1 rootdelay=10'
usb_args_1=boot_dev='usb 1:1'; dev_args='root=/dev/sdb1 rootdelay=10'
usb_args_2=boot_dev='usb 2:1'; dev_args='root=/dev/sdc1 rootdelay=10'
usb_args_3=boot_dev='usb 3:1'; dev_args='root=/dev/sdd1 rootdelay=10'
hd_boot=run ide_start; for scan in 0 1; do run hd_args_$scan ext2_kern ext2_boot
; run ext2_rd ubi_fallback; run fat_kern fat_boot; run fat_rd ubi_fallback; done
######################
Is there a way to rescue my goflex?
Many thanks
Joho