Welcome! Log In Create A New Profile

Advanced

Pogoplug v4 not booting - Serial output

Pogoplug v4 not booting - Serial output
December 22, 2018 07:30AM
Hello, I am new to pogoplug and the first one I bought has never worked properly. I finally figured out I can use a serial connection to it to see what the problem is. But I can't seem to find any answer to uboot not working. I've attached the end of the serial output below, any help would be awesome.Thanks

Quote

[ 1.450000] UBI: background thread "ubi_bgt0d" started, PID 452

[ 1.480000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100

[ 1.500000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00

[ 1.500000] usb usb1: configuration #1 chosen from 1 choice

[ 1.510000] hub 1-0:1.0: USB hub found

[ 1.510000] hub 1-0:1.0: 1 port detected

[ 1.520000] xhci_hcd 0000:00:01.0: xHCI Host Controller

[ 1.520000] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 2

[ 1.530000] xhci_hcd 0000:00:01.0: irq 9, io mem 0xe0000000

[ 1.540000] usb usb2: config 1 interface 0 altsetting 0 endpoint 0x81 has no SuperSpeed companion descriptor

[ 1.550000] usb usb2: configuration #1 chosen from 1 choice

[ 1.550000] hub 2-0:1.0: USB hub found

[ 1.560000] hub 2-0:1.0: 4 ports detected

[ 1.560000] Initializing USB Mass Storage driver...

[ 1.560000] usbcore: registered new interface driver usb-storage

[ 1.570000] USB Mass Storage support registered.

[ 1.580000] usbcore: registered new interface driver ums-datafab

[ 1.580000] usbcore: registered new interface driver ums-freecom

[ 1.590000] usbcore: registered new interface driver ums-jumpshot

[ 1.590000] usbcore: registered new interface driver ums-sddr09

[ 1.600000] usbcore: registered new interface driver ums-sddr55

[ 1.610000] usbcore: registered new interface driver ums-usbat

[ 1.610000] mice: PS/2 mouse device common for all mice

[ 1.620000] i2c /dev entries driver

[ 1.630000] sdhci: Secure Digital Host Controller Interface driver

[ 1.630000] sdhci: Copyright(c) Pierre Ossman

[ 1.640000] mmc0: mvsdio driver initialized, using GPIO 27 for card detection

[ 1.650000] usbcore: registered new interface driver usbhid

[ 1.650000] usbhid: v2.6:USB HID core driver

[ 1.660000] TCP cubic registered

[ 1.660000] NET: Registered protocol family 17

[ 1.670000] RPC: Registered udp transport module.

[ 1.670000] RPC: Registered tcp transport module.

[ 1.680000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)

[ 1.750000] UBIFS: recovery needed

[ 1.830000] UBIFS: recovery completed

[ 1.840000] UBIFS: mounted UBI device 0, volume 0, name "rootfs"

[ 1.840000] UBIFS: file system size: 110469120 bytes (107880 KiB, 105 MiB, 870 LEBs)

[ 1.850000] UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)

[ 1.860000] UBIFS: media format: w4/r0 (latest is w4/r0)

[ 1.860000] UBIFS: default compressor: lzo

[ 1.870000] UBIFS: reserved for root: 0 bytes (0 KiB)

[ 1.870000] VFS: Mounted root (ubifs filesystem) on device 0:11.

[ 1.880000] Freeing init memory: 124K

[ 4.250000] eth0: started

udhcpc (v1.16.1) started

HWADDR 00 0x25 0x31 0x04 0xdf 0x27

PIP0 223

PIP1 39

cat: can't open '/etc/resolv.conf': No such file or directory

route: SIOCDELRT: No such process

grep: /etc/resolv.conf: No such file or directory

Sending discover...

Sending discover...

Sending discover...

HWADDR 00 0x25 0x31 0x04 0xdf 0x27

PIP0 223

PIP1 39

No lease, forking to background

modprobe: module 'vfat' not found

[ 13.870000] ufsd: module license 'Commercial product' taints kernel.

[ 13.880000] Disabling lock debugging due to kernel taint

[ 13.910000] ufsd: driver 8.5 (NTFS4LINUX_U85_017_S[2011-08-17-16:51:48]) LBD=ON with delayalloc with ioctl loaded at bf000000

[ 13.910000] NTFS support included

[ 13.910000] Hfs+/HfsX support included

[ 13.910000] For 'CloudEngines_PogoPlug_2011-08-03'

Loading rt3070sta.ko: [ 14.250000] rtusb init rt2870 --->

[ 14.260000] usbcore: registered new interface driver rt2870

Success

Loading xce.ko: [ 14.280000] Cloud Engines XCE Init [Version: 3.1.99.12]

[ 14.290000] XCE: CPU MEMORY MAP:

[ 14.290000] XCE: -- 0x00001000 - 0xbeffffff (3055 MB) User Space Mappings

[ 14.300000] XCE: -- 0xbf000000 - 0xbfffffff ( 16 MB) Kernel module space

[ 14.310000] XCE: -- 0xc0000000 - 0xc7ffffff ( 128 MB) Kernel direct-mapped ram

[ 14.310000] XCE: -- 0xc8800000 - 0xe7ffffff ( 504 MB) Kernel vmalloc space

[ 14.320000] XCE: -- 0xe8000000 - 0xfeffffff ( 367 MB) Kernel platform space

[ 14.330000] XCE: CPU FEATURES:

[ 14.330000] XCE: -- I Cache: enabled

[ 14.330000] XCE: -- D Cache: enabled

[ 14.340000] XCE: -- Branch Predict: disabled

[ 14.340000] XCE: -- MMU: enabled

[ 14.350000] XCE: -- Alignment Abort: enabled

[ 14.360000] XCE: BLPARAMS: -- Loading properties [c4bf5efc].

[ 14.360000] XCE: BLPARAMS: -- MTD @ [c45c0c00].

[ 14.370000] XCE: BLPARAMS: Locating parameter block...

[ 14.370000] XCE: BLPARAMS: reading 2048 bytes @ a0000

[ 14.380000] XCE: Loaded Property Size: 2048

[ 14.380000] XCE: - 'cesvcid' -> 'C3LDD6S9A32LEDSPJ7GKABA98A'

[ 14.390000] XCE: - 'ceboardver' -> 'PPV4A3'

[ 14.390000] XCE: -- ICache Prefetch: enabled

[ 14.400000] XCE: -- DCache Prefetch: enabled

[ 14.400000] XCE: -- L2 Cache: enabled

[ 14.410000] XCE: -- L2 Prefetch: disabled

[ 14.410000] XCE: -- L2 Writethrough: disabled

[ 14.420000] XCE: -- Write Allocate: disabled

[ 14.420000] XCE: -- Streaming: disabled

[ 14.430000] XCE: Current GPIO State:

[ 14.430000] XCE: GPIO L OUT: 0x01f18400

[ 14.430000] XCE: GPIO L OE: 0xfe004800

[ 14.440000] XCE: GPIO L BLINK: 0x00000000

[ 14.440000] XCE: GPIO L POL: 0x08000000

[ 14.450000] XCE: GPIO L IN: 0x31f00000

[ 14.450000] XCE: GPIO H OUT: 0x00000008

[ 14.450000] XCE: GPIO H OE: 0x00000005

[ 14.460000] XCE: GPIO H BLINK: 0x00000000

[ 14.460000] XCE: GPIO H POL: 0x00000000

[ 14.470000] XCE: GPIO H IN: 0x00000008

Success

Starting hbplug: Success

/ # [ 14.550000] XCE: BLPARAMS: -- Loading properties [c4bf5ecc].

[ 14.560000] XCE: BLPARAMS: -- MTD @ [c45c0c00].

[ 14.560000] XCE: BLPARAMS: Locating parameter block...

[ 14.570000] XCE: BLPARAMS: reading 2048 bytes @ a0000

[ 14.580000] XCE: BLPARAMS: reading 2048 bytes @ a0800

[ 14.580000] XCE: BLPARAMS: reading 2048 bytes @ a1000

[ 14.590000] XCE: BLPARAMS: reading 2048 bytes @ a1800

[ 19.860000] XCE: XCE: LED -> DISCONNECTED
Re: Pogoplug v4 not booting - Serial output
December 22, 2018 05:09PM
brickman7713,

You are booting with stock OS. What is your goal? Do you want to install new Debian rootfs and u-boot? or just want to fix this problem and continue using stock?

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Pogoplug v4 not booting - Serial output
December 22, 2018 05:15PM
I assume it is stock but it has never booted since I bought it. I don't really care what I do with it as long as I fix it, I will probably install debian eventually, but I don't care yet. Thanks for the response
Re: Pogoplug v4 not booting - Serial output
December 22, 2018 07:00PM
brickman7713,

Power up, interrupt serial console at countdown, and

printenv
boot

Please post the entire serial console log (from the u-boot banner until the last line in your terminal session).

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Pogoplug v4 not booting - Serial output
December 22, 2018 07:07PM
I will post the printenv output soon, but how do I copy the complete serial output? I can't scroll up on the terminal on ubuntu
Re: Pogoplug v4 not booting - Serial output
December 22, 2018 10:32PM
This is the printenv output.

CE>> printenv
baudrate=115200
loads_echo=0
rootpath=/mnt/ARM_FS/
netmask=255.255.0.0
run_diag=yes
CASset=min
MALLOC_len=1
ethprime=egiga0
load_nand=nboot 0x800000 0 0x200000
load_nand2=nboot 0x800000 0 0x500000
boot=bootm 0x800000
boot_nand=run load_nand boot || run load_nand2 boot
ethmtu=1500
usb0Mode=host
nandEcc=1bit
ethact=egiga0
ethaddr=00:25:31:04:df:27
cesvcid=C3LDD6S9A32LEDSPJ7GKABA98A
ceboardver=PPV4A3
ipaddr=192.168.58.233
serverip=192.168.58.188
bootargs=console=ttyS0,115200 root=ubi0:rootfs ubi.mtd=4,2048 rootfstype=ubifs
bootcmd=run boot_nand
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=1
disaMvPnp=no
hddPowerCtrl=no
pcieTune=no

Environment size: 834/131068 bytes


And the full boot code, notice at the end I have access to some shell.

U-Boot 1.1.4 (Oct  1 2011 - 12:06:06) Cloud Engines 1.1.2 (3.4.27) PHYADDR=0

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006918B4

Soc: 88F6192 A1 (DDR2)
CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 200Mhz , TClock = 166Mhz

DRAM CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3
DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB
Flash:  0 kB

CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: PPV4A3

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0

Loading from NAND 128MB 3,3V 8-bit, offset 0x200000
   Image Name:   Linux-2.6.31.8
   Created:      2011-09-28  19:09:20 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2080956 Bytes =  2 MB
   Load Address: 00008000
   Entry Point:  00008000
## Booting image at 00800000 ...
   Image Name:   Linux-2.6.31.8
   Created:      2011-09-28  19:09:20 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2080956 Bytes =  2 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux..................................................................................................................................... done, booting the kernel.
[    0.000000] Linux version 2.6.31.8 (afenn@kt) (gcc version 4.3.2 (sdk3.3-ct-ng-1.4.1) ) #5 Wed Sep 28 12:09:12 PDT 2011
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: Feroceon-KW
[    0.000000] Using UBoot passing parameters structure
[    0.000000] Ignoring unrecognised tag 0x41004345
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 root=ubi0:rootfs ubi.mtd=4,2048 rootfstype=ubifs
[    0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 128MB = 128MB total
[    0.000000] Memory: 118356KB available (3852K code, 261K data, 124K init, 0K highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:128
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Calibrating delay loop... 799.53 BogoMIPS (lpj=3997696)
[    0.230000] Mount-cache hash table entries: 512
[    0.230000] CPU: Testing write buffer coherency: ok
[    0.230000] NET: Registered protocol family 16
[    0.230000] Feroceon L2: Enabling L2
[    0.230000] Feroceon L2: Cache support initialised.
[    0.230000]
[    0.230000] CPU Interface
[    0.230000] -------------
[    0.230000] SDRAM_CS0 ....base 00000000, size 128MB
[    0.230000] SDRAM_CS1 ....disable
[    0.230000] SDRAM_CS2 ....disable
[    0.230000] SDRAM_CS3 ....disable
[    0.230000] PEX0_MEM ....base e0000000, size 128MB
[    0.230000] PEX0_IO ....base f2000000, size   1MB
[    0.230000] PEX1_MEM ....no such
[    0.230000] PEX1_IO ....no such
[    0.230000] INTER_REGS ....base f1000000, size   1MB
[    0.230000] NFLASH_CS ....base fa000000, size   2MB
[    0.230000] SPI_CS ....base f4000000, size  16MB
[    0.230000] BOOT_ROM_CS ....no such
[    0.230000] DEV_BOOTCS ....no such
[    0.230000] CRYPT_ENG ....base f0000000, size   2MB
[    0.230000]
[    0.230000]   Marvell Development Board (LSP Version KW_LSP_5.1.3_patch18)-- RD-88F6192A-NAS  Soc: 88F6192 A1 LE
[    0.230000]
[    0.230000]  Detected Tclk 166666667 and SysClk 200000000
[    0.230000] Marvell USB EHCI Host controller #0: c403e740
[    0.730000] PEX0 interface detected Link X1
[    0.740000] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[    0.740000] pci 0000:00:01.0: PME# disabled
[    0.740000] PCI: bus0: Fast back to back transfers disabled
[    0.740000] mvPexLocalBusNumSet: ERR. Invalid PEX interface 1
[    0.750000] bio: create slab <bio-0> at 0
[    0.750000] SCSI subsystem initialized
[    0.750000] usbcore: registered new interface driver usbfs
[    0.750000] usbcore: registered new interface driver hub
[    0.750000] usbcore: registered new device driver usb
[    0.750000] NET: Registered protocol family 2
[    0.750000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.750000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    0.750000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[    0.750000] TCP: Hash tables configured (established 4096 bind 4096)
[    0.750000] TCP reno registered
[    0.750000] NET: Registered protocol family 1
[    0.750000] cpufreq: Init kirkwood cpufreq driver
[    0.760000] XOR registered 4 channels
[    0.760000] XOR 2nd invalidate WA enabled
[    0.760000] cesadev_init(c000d7fc)
[    0.760000] mvCesaInit: sessions=640, queue=64, pSram=f0000000
[    0.760000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.770000] msgmni has been set to 231
[    0.770000] alg: No test for cipher_null (cipher_null-generic)
[    0.770000] alg: No test for ecb(cipher_null) (ecb-cipher_null)
[    0.770000] alg: No test for digest_null (digest_null-generic)
[    0.770000] alg: No test for compress_null (compress_null-generic)
[    0.780000] alg: No test for stdrng (krng)
[    0.780000] alg: No test for hmac(digest_null) (hmac(digest_null-generic))
[    0.790000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.790000] io scheduler noop registered
[    0.790000] io scheduler anticipatory registered (default)
[    0.790000] Initializing ths8200_init
[    0.790000] Initializing dove_adi9889_init
[    0.810000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.810000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[    0.810000] console [ttyS0] enabled
[    0.820000] Integrated Sata device found
[    0.830000] IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
[    0.850000] scsi0 : Marvell SCSI to SATA adapter
[    0.860000] scsi1 : Marvell SCSI to SATA adapter
[    0.870000] Loading Marvell Ethernet Driver:
[    0.870000]   o Cached descriptors in DRAM
[    0.880000]   o DRAM SW cache-coherency
[    0.880000]   o 1 Giga ports supported
[    0.880000]   o Single RX Queue support - ETH_DEF_RXQ=0
[    0.890000]   o Single TX Queue support - ETH_DEF_TXQ=0
[    0.890000]   o TCP segmentation offload (TSO) supported
[    0.900000]   o Large Receive offload (LRO) supported
[    0.900000]   o Receive checksum offload supported
[    0.910000]   o Transmit checksum offload supported
[    0.910000]   o Network Fast Processing (Routing) supported - (Disabled)
[    0.920000]   o Driver ERROR statistics enabled
[    0.930000]   o Proc tool API enabled
[    0.930000]   o SKB Reuse supported - (Disabled)
[    0.930000]   o SKB Recycle supported - (Disabled)
[    0.940000]   o Rx descripors: q0=128
[    0.940000]   o Tx descripors: q0=532
[    0.950000]   o Loading network interface(s):
[    0.950000]      o register under mv88fx_eth platform
[    0.960000]      o eth0, ifindex = 2, GbE port = 0
[    0.960000]
[    0.960000] mvFpRuleDb (c45b1000): 1024 entries, 4096 bytes
[    0.970000] Counter=0, opIdx=6, overhead=16
[    0.970000] Counter=1, opIdx=2, overhead=0
[    0.980000] Counter=2, opIdx=1, overhead=18
[    0.980000] Counter=3, opIdx=2, overhead=0
[    0.990000] tun: Universal TUN/TAP device driver, 1.6
[    0.990000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    1.000000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit)
[    1.010000] Scanning device for bad blocks
[    1.020000] Bad eraseblock 142 at 0x0000011c0000
[    1.030000] Bad eraseblock 266 at 0x000002140000
[    1.030000] Bad eraseblock 319 at 0x0000027e0000
[    1.070000] Using static partition definition
[    1.070000] Creating 5 MTD partitions on "nand_mtd":
[    1.080000] 0x000000000000-0x000000200000 : "u-boot"
[    1.090000] 0x000000200000-0x000000500000 : "uImage"
[    1.090000] 0x000000500000-0x000000800000 : "uImage2"
[    1.100000] 0x000000800000-0x000001000000 : "failsafe"
[    1.100000] 0x000001000000-0x000008000000 : "root"
[    1.110000] UBI: attaching mtd4 to ubi0
[    1.110000] UBI: physical eraseblock size:   131072 bytes (128 KiB)
[    1.120000] UBI: logical eraseblock size:    126976 bytes
[    1.120000] UBI: smallest flash I/O unit:    2048
[    1.130000] UBI: sub-page size:              512
[    1.130000] UBI: VID header offset:          2048 (aligned 2048)
[    1.140000] UBI: data offset:                4096
[    1.360000] UBI: attached mtd4 to ubi0
[    1.370000] UBI: MTD device name:            "root"
[    1.370000] UBI: MTD device size:            112 MiB
[    1.380000] UBI: number of good PEBs:        893
[    1.380000] UBI: number of bad PEBs:         3
[    1.390000] UBI: max. allowed volumes:       128
[    1.390000] UBI: wear-leveling threshold:    4096
[    1.400000] UBI: number of internal volumes: 1
[    1.400000] UBI: number of user volumes:     1
[    1.400000] UBI: available PEBs:             0
[    1.410000] UBI: total number of reserved PEBs: 893
[    1.410000] UBI: number of PEBs reserved for bad PEB handling: 8
[    1.420000] UBI: max/mean erase counter: 1/0
[    1.420000] UBI: image sequence number: 0
[    1.430000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.440000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
[    1.440000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
[    1.450000] UBI: background thread "ubi_bgt0d" started, PID 452
[    1.480000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
[    1.500000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
[    1.500000] usb usb1: configuration #1 chosen from 1 choice
[    1.510000] hub 1-0:1.0: USB hub found
[    1.510000] hub 1-0:1.0: 1 port detected
[    1.520000] xhci_hcd 0000:00:01.0: xHCI Host Controller
[    1.520000] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 2
[    1.530000] xhci_hcd 0000:00:01.0: irq 9, io mem 0xe0000000
[    1.540000] usb usb2: config 1 interface 0 altsetting 0 endpoint 0x81 has no SuperSpeed companion descriptor
[    1.550000] usb usb2: configuration #1 chosen from 1 choice
[    1.550000] hub 2-0:1.0: USB hub found
[    1.560000] hub 2-0:1.0: 4 ports detected
[    1.560000] Initializing USB Mass Storage driver...
[    1.560000] usbcore: registered new interface driver usb-storage
[    1.570000] USB Mass Storage support registered.
[    1.580000] usbcore: registered new interface driver ums-datafab
[    1.580000] usbcore: registered new interface driver ums-freecom
[    1.590000] usbcore: registered new interface driver ums-jumpshot
[    1.590000] usbcore: registered new interface driver ums-sddr09
[    1.600000] usbcore: registered new interface driver ums-sddr55
[    1.610000] usbcore: registered new interface driver ums-usbat
[    1.610000] mice: PS/2 mouse device common for all mice
[    1.620000] i2c /dev entries driver
[    1.630000] sdhci: Secure Digital Host Controller Interface driver
[    1.630000] sdhci: Copyright(c) Pierre Ossman
[    1.640000] mmc0: mvsdio driver initialized, using GPIO 27 for card detection
[    1.650000] usbcore: registered new interface driver usbhid
[    1.650000] usbhid: v2.6:USB HID core driver
[    1.660000] TCP cubic registered
[    1.660000] NET: Registered protocol family 17
[    1.670000] RPC: Registered udp transport module.
[    1.670000] RPC: Registered tcp transport module.
[    1.680000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.840000] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    1.840000] UBIFS: file system size:   110469120 bytes (107880 KiB, 105 MiB, 870 LEBs)
[    1.850000] UBIFS: journal size:       9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
[    1.860000] UBIFS: media format:       w4/r0 (latest is w4/r0)
[    1.860000] UBIFS: default compressor: lzo
[    1.870000] UBIFS: reserved for root:  0 bytes (0 KiB)
[    1.870000] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    1.880000] Freeing init memory: 124K
[    4.250000] eth0: started
udhcpc (v1.16.1) started
HWADDR 00 0x25 0x31 0x04 0xdf 0x27
PIP0 223
PIP1 39
cat: can't open '/etc/resolv.conf': No such file or directory
route: SIOCDELRT: No such process
grep: /etc/resolv.conf: No such file or directory
Sending discover...
Sending discover...
Sending discover...
HWADDR 00 0x25 0x31 0x04 0xdf 0x27
PIP0 223
PIP1 39
No lease, forking to background
modprobe: module 'vfat' not found
[   13.870000] ufsd: module license 'Commercial product' taints kernel.
[   13.880000] Disabling lock debugging due to kernel taint
[   13.910000] ufsd: driver 8.5 (NTFS4LINUX_U85_017_S[2011-08-17-16:51:48]) LBD=ON with delayalloc with ioctl loaded at bf000000
[   13.910000] NTFS support included
[   13.910000] Hfs+/HfsX support included
[   13.910000] For 'CloudEngines_PogoPlug_2011-08-03'
Loading rt3070sta.ko:        [   14.250000] rtusb init rt2870 --->
[   14.260000] usbcore: registered new interface driver rt2870
Success
Loading xce.ko:              [   14.280000] Cloud Engines XCE Init [Version: 3.1.99.12]
[   14.290000] XCE: CPU MEMORY MAP:
[   14.290000] XCE:   -- 0x00001000 - 0xbeffffff (3055 MB)  User Space Mappings
[   14.300000] XCE:   -- 0xbf000000 - 0xbfffffff (  16 MB)  Kernel module space
[   14.310000] XCE:   -- 0xc0000000 - 0xc7ffffff ( 128 MB)  Kernel direct-mapped ram
[   14.310000] XCE:   -- 0xc8800000 - 0xe7ffffff ( 504 MB)  Kernel vmalloc space
[   14.320000] XCE:   -- 0xe8000000 - 0xfeffffff ( 367 MB)  Kernel platform space
[   14.330000] XCE: CPU FEATURES:
[   14.330000] XCE:   -- I Cache:         enabled
[   14.330000] XCE:   -- D Cache:         enabled
[   14.340000] XCE:   -- Branch Predict:  disabled
[   14.340000] XCE:   -- MMU:             enabled
[   14.350000] XCE:   -- Alignment Abort: enabled
[   14.360000] XCE: BLPARAMS:   -- Loading properties [c4d07efc].
[   14.360000] XCE: BLPARAMS:   -- MTD @ [c45c0c00].
[   14.370000] XCE: BLPARAMS: Locating parameter block...
[   14.370000] XCE: BLPARAMS: reading 2048 bytes @ a0000
[   14.380000] XCE: Loaded Property Size: 2048
[   14.380000] XCE:    - 'cesvcid' -> 'C3LDD6S9A32LEDSPJ7GKABA98A'
[   14.390000] XCE:    - 'ceboardver' -> 'PPV4A3'
[   14.390000] XCE:   -- ICache Prefetch: enabled
[   14.400000] XCE:   -- DCache Prefetch: enabled
[   14.400000] XCE:   -- L2 Cache:        enabled
[   14.410000] XCE:   -- L2 Prefetch:     disabled
[   14.410000] XCE:   -- L2 Writethrough: disabled
[   14.420000] XCE:   -- Write Allocate:  disabled
[   14.420000] XCE:   -- Streaming:       disabled
[   14.430000] XCE: Current GPIO State:
[   14.430000] XCE:  GPIO L OUT:    0x01f18400
[   14.430000] XCE:  GPIO L OE:     0xfe004800
[   14.440000] XCE:  GPIO L BLINK:  0x00000000
[   14.440000] XCE:  GPIO L POL:    0x08000000
[   14.450000] XCE:  GPIO L IN:     0x31f00000
[   14.450000] XCE:  GPIO H OUT:    0x00000008
[   14.450000] XCE:  GPIO H OE:     0x00000005
[   14.460000] XCE:  GPIO H BLINK:  0x00000000
[   14.460000] XCE:  GPIO H POL:    0x00000000
[   14.470000] XCE:  GPIO H IN:     0x00000008
Success
Starting hbplug:             Success
/ # [   14.550000] XCE: BLPARAMS:   -- Loading properties [c4d07ecc].
[   14.560000] XCE: BLPARAMS:   -- MTD @ [c45c0c00].
[   14.560000] XCE: BLPARAMS: Locating parameter block...
[   14.570000] XCE: BLPARAMS: reading 2048 bytes @ a0000
[   14.580000] XCE: BLPARAMS: reading 2048 bytes @ a0800
[   14.580000] XCE: BLPARAMS: reading 2048 bytes @ a1000
[   14.590000] XCE: BLPARAMS: reading 2048 bytes @ a1800
[   19.860000] XCE: XCE: LED -> DISCONNECTED

/ #
/ #



Edited 1 time(s). Last edit at 12/22/2018 10:49PM by brickman7713@gmail.com.
Re: Pogoplug v4 not booting - Serial output
December 23, 2018 01:13AM
brickman7713,

It is working fine. Nothing is wrong with your box.

You know that free Pogoplug service has been discontinued? when you boot this box into the stock OS like this, it is working as intended.

Now, in the old days, when this box is supported by the manufacterer, you can visit the box own webpage, log in and enable SSH... do all that. But since this box been EOL, that is something you must do manually. And then use this box in your network as a NAS.

However, to use it as NAS (without Pogolug service), you should install new Debian system and U-Boot to maximize the capabilty of the hardware.

Debian:
https://forum.doozan.com/read.php?2,12096

U-Boot:
https://forum.doozan.com/read.php?3,12381

-bodhi
===========================
Forum Wiki
bodhi's corner



Edited 2 time(s). Last edit at 12/23/2018 04:05AM by bodhi.
Re: Pogoplug v4 not booting - Serial output
December 23, 2018 07:34AM
Ok thanks, can you tell me why I get a red light then and I can’t connect to it through the network at all? Or how to enable ssh via serial
Re: Pogoplug v4 not booting - Serial output
December 23, 2018 01:11PM
brickman7713,

> Ok thanks, can you tell me why I get a red light
> then and I can’t connect to it through the
> network at all? Or how to enable ssh via serial

Red LED light means the kernel did not set it to Green because of errors. In stock OS, this behavior could mean any type of error, including failing to phone home (Pogoplug service always try to connect to home server when system starts).

As you can guess, this stock topic is quite old :) so I lost the links to forum posts that show you how to set up SSH permanently in stock OS.

Basically you need to set up to run dropbear in stock so that SSH is enabled. Somewhere in the forum there should be posts discussing this topic.

I'll search in my notes to find the instruction.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Pogoplug v4 not booting - Serial output
December 23, 2018 01:52PM
Ok enbled SSH with this method https://www.reddit.com/r/pogoplug/comments/5m9sd6/pogoplug_is_dead/. Now I can follow the debian guide?
Re: Pogoplug v4 not booting - Serial output
December 23, 2018 01:55PM
I guess not since I can't find the /boot directory
Re: Pogoplug v4 not booting - Serial output
December 23, 2018 08:29PM
brickman7713,

The Debian installation is to USB. So it has nothing to do with stock /boot. You would create the rootfs using Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2 (24 Jul 2017) following the instruction:

https://forum.doozan.com/read.php?2,12096

I's suggest read the first post, and then scrolldown to


Quote

Updated 24 Jul 2017:

Basic Debian stretch Kirkwood rootfs for most Kirwood plugs:

- tarball size: 188M
- install size: 488M
- The init system used in this rootfs is sysvinit . To boot with systemd, see note 2 below.
- Installed packages: nano, avahi, ntp, busybox-syslogd (log to RAM), htop, isc-dhcp-client, dialog, bzip2, nfs server/client, iperf, ethtool, sysvinit-core, sysvinit, and sysvinit-utils.
- see LED controls in /etc/rc.local, and /etc/init.d/halt
- see some useful aliases in /root/.profile
- root password: root

Download at Dropbox:

Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2

md5:
bf3d29569943875df348fb5ca03b348c
sha256:
4ed5714fdb123cdb40e973f3d0754e91cd199b75a9874018f2b5dc9cfa8ae8bb

You need to do a lot of reading to get familiar with the manual installation procedures of Debian rootf and u-boot first.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Pogoplug v4 not booting - Serial output
December 23, 2018 08:30PM
Ok thank you, so Debian will rub off from a flash drive correct?
Re: Pogoplug v4 not booting - Serial output
December 23, 2018 08:32PM
brickman7713@gmail.com Wrote:
-------------------------------------------------------
> Ok thank you, so Debian will rub off from a flash
> drive correct?

Correct. This is how you get to run a full Debian system with the latest kernel.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Pogoplug v4 not booting - Serial output
December 23, 2018 08:33PM
Cool hopefully I’ll get to it in the next couple days, thanks for all the help.
Re: Pogoplug v4 not booting - Serial output
December 24, 2018 03:21PM
So I read through that and I'm still a little confused. Do I need to install debian on a USB myself before following that guide?
Re: Pogoplug v4 not booting - Serial output
December 24, 2018 05:47PM
brickman7713@gmail.com Wrote:
-------------------------------------------------------
> So I read through that and I'm still a little
> confused. Do I need to install debian on a USB
> myself before following that guide?

No. The rootfs Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2 is a full Debian system, with LInux kernel 4.12.1-kirkwood-tld-1 installed in it. All you need to do is to extract it to a USB drive as instructed.

From now on this USB drive is your system. Eventually, if you like to run your system with HDD, then clone this over to the HDD (instrucition for this is available here).

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Pogoplug v4 not booting - Serial output
December 24, 2018 08:13PM
Ok thanks again, so I extract the tar too the root of the flash drive then follow the instructions on the link you sent me before.
Re: Pogoplug v4 not booting - Serial output
December 24, 2018 09:53PM
I am stuck on the "apt-get remove flash-kernel" command, I get an error "unable to locate package flash kernel"
Re: Pogoplug v4 not booting - Serial output
December 25, 2018 03:24PM
brickman7713,


> I am stuck on the "apt-get remove flash-kernel"
> command, I get an error "unable to locate package
> flash kernel"


You were looking at the wrong section. Please reread the post above:

https://forum.doozan.com/read.php?3,75329,75449#msg-75449

Basically, the rootfs Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2 (dated 24 Jul 2017) is all you need to create (you tried to follow the kernel section of the post)

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Pogoplug v4 not booting - Serial output
December 25, 2018 05:04PM
Ok so I think I got the usb drive all set, how do I get the pogoplug to boot from it now? I don't see that in the instructions
Re: Pogoplug v4 not booting - Serial output
December 25, 2018 05:38PM
Next is installing u-boot. I mentiond this above:

https://forum.doozan.com/read.php?3,75329,75374#msg-75374

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Pogoplug v4 not booting - Serial output
December 28, 2018 08:13AM
Got it thanks! I am now running debian on my pogoplug
Author:

Your Email:


Subject:


Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: