Stubborn Stora January 15, 2019 03:44PM |
Registered: 6 years ago Posts: 2 |
Re: Stubborn Stora January 15, 2019 11:34PM |
Admin Registered: 14 years ago Posts: 19,547 |
setenv set_bootargs 'setenv bootargs console=ttys0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial' boot
Re: Stubborn Stora January 16, 2019 01:23PM |
Registered: 6 years ago Posts: 2 |
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:38:05 -0700) Netgear Stora MS2110 SoC: Kirkwood 88F6281_A0 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 PHY reset timed out 88E1116 Initialized on egiga0 Hit any key to stop autoboot: 0 Netgear Stora> setenv set_bootargs 'setenv bootargs console=ttys0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial' Netgear Stora> saveenv Saving Environment to NAND... Erasing NAND... Erasing at 0xc0000 -- 100% complete. Writing to NAND... OK Netgear Stora> boot starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... EHCI timed out on TD - token=0x80008c80 unable to get device descriptor (error=-1) retry: 5 2 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 5 second(s) 1 Storage Device(s) found Reset IDE: Bus 0: OK Bus 1: OK Device 0: Model: WDC WD30EZRX-00SPEB0 Firm: 80.00A80 Ser#: WD-WCC4E0373115 Type: Hard Disk Supports 48-bit addressing Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512) Device 1: Model: WDC WD30EZRX-00SPEB0 Firm: 80.00A80 Ser#: WD-WCC4E0366238 Type: Hard Disk Supports 48-bit addressing Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512) Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 3991552 0c4ea8d9-01 83 Boot ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** Partition Map for IDE device 0 -- Partition Type: EFI Part Start LBA End LBA Name Attributes Type GUID Partition GUID 1 0x00000022 0x15d50a38e "primary" attrs: 0x0000000000000000 type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7 type: data guid: e85015e8-c49a-447a-933f-c3ce63bfe7cd Partition Map for IDE device 1 -- Partition Type: EFI Part Start LBA End LBA Name Attributes Type GUID Partition GUID 1 0x00000022 0x15d50a38e "primary" attrs: 0x0000000000000000 type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7 type: data guid: ee6d64bf-3fca-4520-a17d-a7a533559e77 running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 691 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 4065608 bytes read in 1032 ms (3.8 MiB/s) loading uInitrd ... 8691155 bytes read in 1259 ms (6.6 MiB/s) loading DTB /boot/dts/kirkwood-netgear_stora_ms2000.dtb ... 11499 bytes read in 2615 ms (3.9 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.16.1-kirkwood-tld-1 Created: 2018-05-31 19:23:58 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4065544 Bytes = 3.9 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.16.1-kirkwood-tld-1 Created: 2018-05-31 19:26:20 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 8691091 Bytes = 8.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 037b6000, end 03fffd93 ... OK Loading Device Tree to 037b0000, end 037b5cea ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.16.1-kirkwood-tld-1 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 PREEMPT Mon Apr 9 00:51:18 PDT 2018 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: NETGEAR MS2000 / MS2110 aka Stora [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] random: fast init done [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttys0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) earlyprintk=serial [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 108008K/131072K available (8192K kernel code, 754K rwdata, 2088K rodata, 1024K init, 282K bss, 23064K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (9184 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 755 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 283 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000011] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.007906] Switching to timer-based delay loop, resolution 5ns [ 0.014553] Console: colour dummy device 80x30 [ 0.019117] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.029761] pid_max: default: 32768 minimum: 301 [ 0.034776] Security Framework initialized [ 0.039139] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.045806] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.054099] CPU: Testing write buffer coherency: ok [ 0.060386] Setting up static identity map for 0x100000 - 0x100058 [ 0.066931] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.072482] Hierarchical SRCU implementation. [ 0.081040] devtmpfs: initialized [ 0.090338] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.100347] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.106970] prandom: seed boundary self test passed [ 0.116973] prandom: 100 self tests passed [ 0.121145] pinctrl core: initialized pinctrl subsystem [ 0.127970] NET: Registered protocol family 16 [ 0.133059] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.140813] audit: initializing netlink subsys (disabled) [ 0.147506] audit: type=2000 audit(0.130:1): state=initialized audit_enabled=0 res=1 [ 0.155462] cpuidle: using governor ladder [ 0.159734] cpuidle: using governor menu [ 0.164310] Feroceon L2: Enabling L2 [ 0.168047] Feroceon L2: Cache support initialised. [ 0.173372] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.189978] No ATAGs? [ 0.199985] vgaarb: loaded [ 0.205367] SCSI subsystem initialized [ 0.209729] usbcore: registered new interface driver usbfs [ 0.215314] usbcore: registered new interface driver hub [ 0.220848] usbcore: registered new device driver usb [ 0.227166] clocksource: Switched to clocksource orion_clocksource [ 0.348006] VFS: Disk quotas dquot_6.6.0 [ 0.352043] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.370103] NET: Registered protocol family 2 [ 0.375379] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes) [ 0.383193] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.390267] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.396663] TCP: Hash tables configured (established 1024 bind 1024) [ 0.403203] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.409117] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.415676] NET: Registered protocol family 1 [ 0.420755] RPC: Registered named UNIX socket transport module. [ 0.426706] RPC: Registered udp transport module. [ 0.431526] RPC: Registered tcp transport module. [ 0.436254] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.443080] Unpacking initramfs... [ 1.371288] Freeing initrd memory: 8488K [ 1.375445] NetWinder Floating Point Emulator V0.97 (double precision) [ 1.383305] Initialise system trusted keyrings [ 1.387916] Key type blacklist registered [ 1.392148] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 1.398803] zbud: loaded [ 1.402491] NFS: Registering the id_resolver key type [ 1.407681] Key type id_resolver registered [ 1.411882] Key type id_legacy registered [ 1.415926] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.422727] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 1.429488] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.436810] fuse init (API version 7.26) [ 1.441240] orangefs_debugfs_init: called with debug mask: :none: :0: [ 1.447948] orangefs_init: module version upstream loaded [ 1.453374] SGI XFS with ACLs, security attributes, realtime, scrub, no debug enabled [ 8.621921] Key type asymmetric registered [ 8.626047] Asymmetric key parser 'x509' registered [ 8.631345] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 8.638921] io scheduler noop registered [ 8.642866] io scheduler deadline registered [ 8.647340] io scheduler cfq registered (default) [ 8.653645] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 8.663539] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 8.671249] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 8.677584] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 8.684501] pci_bus 0000:00: root bus resource [bus 00-ff] [ 8.690432] PCI: bus0: Fast back to back transfers disabled [ 8.696050] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 8.704322] PCI: bus1: Fast back to back transfers enabled [ 8.709928] pci 0000:00:01.0: PCI bridge to [bus 01] [ 8.715621] mv_xor f1060800.xor: Marvell shared XOR driver [ 8.778161] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 8.785779] mv_xor f1060900.xor: Marvell shared XOR driver [ 8.848150] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 8.856003] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 8.863991] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 8.880892] loop: module loaded [ 8.884722] sata_mv f1080000.sata: slots 32 ports 2 [ 8.892877] scsi host0: sata_mv [ 8.896626] scsi host1: sata_mv [ 8.900082] ata1: SATA max UDMA/133 irq 33 [ 8.904206] ata2: SATA max UDMA/133 irq 33 [ 8.909289] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xda [ 8.915788] nand: Samsung NAND 256MiB 3,3V 8-bit [ 8.920476] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 8.928114] Scanning device for bad blocks [ 8.955180] Bad eraseblock 212 at 0x000001a80000 [ 8.964540] Bad eraseblock 256 at 0x000002000000 [ 8.969256] Bad eraseblock 257 at 0x000002020000 [ 8.980217] Bad eraseblock 316 at 0x000002780000 [ 8.984910] Bad eraseblock 317 at 0x0000027a0000 [ 9.088864] Bad eraseblock 1236 at 0x000009a80000 [ 9.098315] Bad eraseblock 1280 at 0x00000a000000 [ 9.103092] Bad eraseblock 1281 at 0x00000a020000 [ 9.114264] Bad eraseblock 1341 at 0x00000a7a0000 [ 9.195620] 4 cmdlinepart partitions found on MTD device orion_nand [ 9.201971] Creating 4 MTD partitions on "orion_nand": [ 9.207199] 0x000000000000-0x000000100000 : "u-boot" [ 9.213376] 0x000000100000-0x000000500000 : "uImage" [ 9.219504] 0x000000500000-0x000002500000 : "rootfs" [ 9.225813] 0x000002500000-0x000010000000 : "data" [ 9.234825] libphy: Fixed MDIO Bus: probed [ 9.239995] libphy: orion_mdio_bus: probed [ 9.244143] [Firmware Warn]: /ocp@f1000000/mdio-bus@72004/ethernet-phy@8: Whitelisted compatible string. Please remove [ 9.261296] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 9.407224] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 9.416013] ata1.00: ATA-9: WDC WD30EZRX-00SPEB0, 80.00A80, max UDMA/133 [ 9.422789] ata1.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 9.432214] ata1.00: configured for UDMA/133 [ 9.447119] scsi 0:0:0:0: Direct-Access ATA WDC WD30EZRX-00S 0A80 PQ: 0 ANSI: 5 [ 9.456485] sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB) [ 9.464877] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 9.477323] sd 0:0:0:0: [sda] Write Protect is off [ 9.487309] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 9.580952] sda: sda1 [ 9.588095] sd 0:0:0:0: [sda] Attached SCSI disk [ 9.967208] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 9.987370] ata2.00: ATA-9: WDC WD30EZRX-00SPEB0, 80.00A80, max UDMA/133 [ 9.994112] ata2.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 10.009769] ata2.00: configured for UDMA/133 [ 10.024610] scsi 1:0:0:0: Direct-Access ATA WDC WD30EZRX-00S 0A80 PQ: 0 ANSI: 5 [ 10.033932] sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB) [ 10.042131] sd 1:0:0:0: [sdb] 4096-byte physical blocks [ 10.047519] sd 1:0:0:0: [sdb] Write Protect is off [ 10.052486] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 10.117968] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:26:f2:bb:20:6c [ 10.127081] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 10.134021] ehci-pci: EHCI PCI platform driver [ 10.139107] sdb: sdb1 [ 10.142384] ehci-orion: EHCI orion driver [ 10.146693] orion-ehci f1050000.ehci: EHCI Host Controller [ 10.153175] sd 1:0:0:0: [sdb] Attached SCSI disk [ 10.157944] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 10.165852] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 10.197213] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 10.203549] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 10.210414] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.217699] usb usb1: Product: EHCI Host Controller [ 10.222601] usb usb1: Manufacturer: Linux 4.16.1-kirkwood-tld-1 ehci_hcd [ 10.229356] usb usb1: SerialNumber: f1050000.ehci [ 10.234802] hub 1-0:1.0: USB hub found [ 10.238694] hub 1-0:1.0: 1 port detected [ 10.243430] usbcore: registered new interface driver usb-storage [ 10.249947] mousedev: PS/2 mouse device common for all mice [ 10.607211] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 10.808231] usb 1-1: New USB device found, idVendor=1e3d, idProduct=2096 [ 10.814986] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 10.822187] usb 1-1: Product: Flash Disk [ 10.826671] usb 1-1: Manufacturer: USB 2.0 [ 10.830898] usb 1-1: SerialNumber: CCBB0406031257390582548400 [ 10.837455] usb-storage 1-1:1.0: USB Mass Storage device detected [ 10.844025] scsi host2: usb-storage 1-1:1.0 [ 11.297222] rtc-mv f1010300.rtc: internal RTC not ticking [ 11.302848] i2c /dev entries driver [ 11.313500] rtc-pcf8563 0-0051: rtc core: registered rtc-pcf8563 as rtc0 [ 11.323563] hidraw: raw HID events driver (C) Jiri Kosina [ 11.329491] drop_monitor: Initializing network drop monitor service [ 11.336132] NET: Registered protocol family 17 [ 11.340743] Key type dns_resolver registered [ 11.345955] registered taskstats version 1 [ 11.350121] Loading compiled-in X.509 certificates [ 11.355008] zswap: loaded using pool lzo/zbud [ 11.386610] Key type big_key registered [ 11.402966] Key type encrypted registered [ 11.410378] rtc-pcf8563 0-0051: setting system clock to 2019-01-16 19:13:54 UTC (1547666034) [ 11.419751] Warning: unable to open an initial console. [ 11.428599] Freeing unused kernel memory: 1024K [ 11.433861] Checked W+X mappings: passed, no W+X pages found [ 11.554437] systemd-udevd[113]: starting version 232 [ 11.858378] scsi 2:0:0:0: Direct-Access USB 2.0 Flash Disk 5.00 PQ: 0 ANSI: 2 [ 11.875719] sd 2:0:0:0: [sdc] 3993600 512-byte logical blocks: (2.04 GB/1.90 GiB) [ 11.889809] sd 2:0:0:0: [sdc] Write Protect is off [ 11.899572] sd 2:0:0:0: [sdc] No Caching mode page found [ 11.904962] sd 2:0:0:0: [sdc] Assuming drive cache: write through [ 11.927291] sdc: sdc1 [ 11.934795] sd 2:0:0:0: [sdc] Attached SCSI removable disk [ 12.073646] usbcore: registered new interface driver uas [ 12.544869] md127: Warning: Device sdb1 is misaligned [ 12.561227] md127: detected capacity change from 0 to 6001185521664 [ 13.219193] raid6: int32x1 gen() 72 MB/s [ 13.387704] raid6: int32x1 xor() 50 MB/s [ 13.557454] raid6: int32x2 gen() 92 MB/s [ 13.727246] raid6: int32x2 xor() 72 MB/s [ 13.897548] raid6: int32x4 gen() 98 MB/s [ 14.067295] raid6: int32x4 xor() 67 MB/s [ 14.237481] raid6: int32x8 gen() 103 MB/s [ 14.407541] raid6: int32x8 xor() 70 MB/s [ 14.411834] raid6: using algorithm int32x8 gen() 103 MB/s [ 14.417288] raid6: .... xor() 70 MB/s, rmw enabled [ 14.422105] raid6: using intx1 recovery algorithm [ 14.432275] xor: measuring software checksum speed [ 14.528839] arm4regs : 902.800 MB/sec [ 14.627266] 8regs : 542.000 MB/sec [ 14.727286] 32regs : 788.400 MB/sec [ 14.731494] xor: using function: arm4regs (902.800 MB/sec) [ 14.749176] async_tx: api initialized (async) [ 30.157420] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null) [ 30.327034] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000200 [ 30.327034] [ 30.336226] CPU: 0 PID: 1 Comm: init Not tainted 4.16.1-kirkwood-tld-1 #1 [ 30.343046] Hardware name: Marvell Kirkwood (Flattened Device Tree) [ 30.349377] [<c010f3f4>] (unwind_backtrace) from [<c010b734>] (show_stack+0x10/0x14) [ 30.357173] [<c010b734>] (show_stack) from [<c01198a8>] (panic+0xc0/0x258) [ 30.364094] [<c01198a8>] (panic) from [<c011b92c>] (do_exit+0x5e4/0xa64) [ 30.370834] [<c011b92c>] (do_exit) from [<c011ceac>] (do_group_exit+0xec/0xf0) [ 30.378096] [<c011ceac>] (do_group_exit) from [<c011cec0>] (SyS_exit_group+0x10/0x14) [ 30.385968] [<c011cec0>] (SyS_exit_group) from [<c0101000>] (ret_fast_syscall+0x0/0x50) [ 30.394007] Exception stack(0xc783bfa8 to 0xc783bff0) [ 30.399086] bfa0: 00000000 00000004 00000002 00000000 00000002 00000001 [ 30.407302] bfc0: 00000000 00000004 0000037c 000000f8 be99bf04 00000000 00000002 00000000 [ 30.415513] bfe0: b6e42804 be99b918 004796e4 b6e42814 [ 30.420600] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000200 [ 30.420600] [ 50.177232] random: crng init done"
Re: Stubborn Stora January 17, 2019 03:46AM |
Admin Registered: 14 years ago Posts: 19,547 |