Pogoplug v4 not starting August 16, 2019 10:37PM |
Registered: 9 years ago Posts: 66 |
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) Pogoplug V4 gcc (Debian 4.9.2-10) 4.9.2 GNU ld (GNU Binutils for Debian) 2.25 Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Reset IDE: ide_preinit failed MMC rescan: current device # 0 initialized OK no USB devices available no IDE devices available Partition Map for MMC device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 15517696 00013210-01 83 loading envs from mmc 0 ... 98 bytes read in 948 ms (0 Bytes/s) importing envs ... running scan_disk ... Scan device mmc MMC rescan: current device # 0 initialized OK device mmc 0:1 1 bytes read in 515 ms (0 Bytes/s) Found bootable drive on mmc 0 loading uImage ... 3232368 bytes read in 875 ms (3.5 MiB/s) loading uInitrd ... 6838053 bytes read in 1413 ms (4.6 MiB/s) loading DTB /boot/dts/kirkwood-pogoplug_v4.dtb ... 10266 bytes read in 4532 ms (2 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.8.3-kirkwood-tld-1 Created: 2016-12-07 15:25:08 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3232304 Bytes = 3.1 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.8.3-kirkwood-tld-1 Created: 2016-12-07 15:25:48 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6837989 Bytes = 6.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Starting kernel ...
Re: Pogoplug v4 not starting August 16, 2019 10:59PM |
Admin Registered: 13 years ago Posts: 18,555 |
ping debian.localor see if a new IP address was on the router list.
Re: Pogoplug v4 not starting August 16, 2019 11:09PM |
Registered: 9 years ago Posts: 66 |
Re: Pogoplug v4 not starting August 17, 2019 05:25AM |
Admin Registered: 13 years ago Posts: 18,555 |
umount /media/sdb1 e2fsck /dev/sdb1 syncAnd bring it back to the box, power up, see if the LED flash and then turn green.
Re: Pogoplug v4 not starting August 17, 2019 08:27AM |
Registered: 9 years ago Posts: 66 |
64 bytes from 192.168.1.104: icmp_seq=1 ttl=64 time=8.22 ms 64 bytes from 192.168.1.104: icmp_seq=2 ttl=64 time=4.16 ms From 192.168.1.114 icmp_seq=9 Destination Host Unreachable From 192.168.1.114 icmp_seq=10 Destination Host Unreachable From 192.168.1.114 icmp_seq=11 Destination Host Unreachable From 192.168.1.114 icmp_seq=12 Destination Host Unreachable
Re: Pogoplug v4 not starting August 17, 2019 01:34PM |
Registered: 7 years ago Posts: 366 |
Re: Pogoplug v4 not starting August 17, 2019 03:37PM |
Admin Registered: 13 years ago Posts: 18,555 |
Re: Pogoplug v4 not starting August 17, 2019 11:14PM |
Registered: 9 years ago Posts: 66 |
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) Pogoplug V4 gcc (Debian 4.9.2-10) 4.9.2 GNU ld (GNU Binutils for Debian) 2.25 Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Reset IDE: ide_preinit failed MMC rescan: current device # 0 initialized OK no USB devices available no IDE devices available Partition Map for MMC device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 15661056 61872a2a-01 83 loading envs from mmc 0 ... ** File not found /boot/uEnv.txt ** running scan_disk ... Scan device usb device usb 0:1 ** Bad device usb 0 ** device usb 1:1 ** Bad device usb 1 ** device usb 2:1 ** Bad device usb 2 ** device usb 3:1 ** Bad device usb 3 ** Scan device ide Reset IDE: ide_preinit failed device ide 0:1 ** Bad device size - ide 0 ** device ide 1:1 ** Bad device size - ide 1 ** device ide 2:1 ** Bad device ide 2 ** device ide 3:1 ** Bad device ide 3 ** Scan device mmc MMC rescan: current device # 0 initialized OK device mmc 0:1 1 bytes read in 885 ms (0 Bytes/s) Found bootable drive on mmc 0 loading uImage ... 3821592 bytes read in 1455 ms (2.5 MiB/s) loading uInitrd ... 7245696 bytes read in 1642 ms (4.2 MiB/s) loading DTB /boot/dts/kirkwood-pogoplug_v4.dtb ... 10284 bytes read in 2346 ms (3.9 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.12.1-kirkwood-tld-1 Created: 2017-07-20 8:11:24 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3821528 Bytes = 3.6 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.12.1-kirkwood-tld-1 Created: 2017-07-24 0:18:23 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7245632 Bytes = 6.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Starting kernel ...
Re: Pogoplug v4 not starting August 17, 2019 11:15PM |
Registered: 9 years ago Posts: 66 |
Re: Pogoplug v4 not starting August 18, 2019 03:29AM |
Admin Registered: 13 years ago Posts: 18,555 |
printenv boot
Re: Pogoplug v4 not starting August 18, 2019 07:55AM |
Registered: 9 years ago Posts: 66 |
Re: Pogoplug v4 not starting August 18, 2019 09:35AM |
Registered: 9 years ago Posts: 66 |
printenv arcNumber=3960 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-pogoplug_v4.dtb ethact=egiga0 ethaddr=52:3b:20:9c:11:51 if_netconsole=ping $serverip ipaddr=192.168.1.104 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 machid=f78 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) nc_ready=1 ncip=192.168.1.108 partition=nand0,2 preboot=run preboot_nc preboot_nc=setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.1.108 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=nc stdin=nc stdout=nc uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_ready_retry=15 Environment size: 3059/131068 bytes
Re: Pogoplug v4 not starting August 18, 2019 04:36PM |
Admin Registered: 13 years ago Posts: 18,555 |
Re: Pogoplug v4 not starting August 18, 2019 05:14PM |
Registered: 7 years ago Posts: 366 |
Re: Pogoplug v4 not starting August 18, 2019 06:30PM |
Admin Registered: 13 years ago Posts: 18,555 |
ping debian.local
Re: Pogoplug v4 not starting August 18, 2019 08:53PM |
Registered: 9 years ago Posts: 66 |
Re: Pogoplug v4 not starting August 18, 2019 08:55PM |
Registered: 9 years ago Posts: 66 |
> ping debian.local >It seems the SD card reader may have a fault. when I tried using the existing SD card as well as new SD with the boot/rootfs you have mentioned, it simply stalls at 'Starting kernel'. When I use the USB drive the plug works fine.Thanks for your time.