Rescue system install on tftp? Need Help October 02, 2012 04:34PM |
Registered: 11 years ago Posts: 10 |
U-Boot 2010.09 (Oct 23 2010 - 11:49:22) Marvell-Dockstar/Pogoplug by Jeff Doozan SoC: Kirkwood 88F6281_A0 DRAM: 128 MiB NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 88E1116 Initialized on egiga0 Hit any key to stop autoboot: 0 Marvell>> nand erase 0x100000 0x400000 NAND erase: device 0 offset 0x100000, size 0x400000 Erasing at 0x4e0000 -- 100% complete. OK Marvell>> tftp 0x800000 uImage-mtd1.img Using egiga0 device TFTP from server 192.168.2.36; our IP address is 192.168.2.210 Filename 'uImage-mtd1.img'. Load address: 0x800000 Loading: ################################################################# ################################################################# ################################################################# ######################################################## done Bytes transferred = 3670016 (380000 hex) Marvell>> nand write.e 0x800000 0x100000 0x380000 NAND write: device 0 offset 0x100000, size 0x380000 3670016 bytes written: OK Marvell>> tftp 0x1000000 rootfs-mtd2.img Using egiga0 device TFTP from server 192.168.2.36; our IP address is 192.168.2.210 Filename 'rootfs-mtd2.img'. Load address: 0x1000000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###### done Bytes transferred = 28704768 (1b60000 hex) Marvell>> setenv rescue_set_bootargs 'setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params' Marvell>> setenv rescue_bootcmd 'if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi' Marvell>> setenv bootcmd 'run bootcmd_usb; usb stop; run rescue_bootcmd; reset' Marvell>> saveenv Saving Environment to NAND... Erasing Nand... Erasing at 0xc0000 -- 100% complete. Writing to Nand... done Marvell>> run rescue_bootcmd NAND read: device 0 offset 0x100000, size 0x400000 4194304 bytes read: OK ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.3.2-kirkwide Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3627768 Bytes = 3.5 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.3.2-kirkwide (davygravy@bitbaker64) (gcc version 4.3.5 (Buildroot 2010.08) ) #1 Mon May 28 13:23:17 CDT 2012 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977 [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: Marvell SheevaPlug Reference Board [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 128MB = 128MB total [ 0.000000] Memory: 122080k/122080k available, 8992k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc06c06c8 (6882 kB) [ 0.000000] .init : 0xc06c1000 - 0xc06eb000 ( 168 kB) [ 0.000000] .data : 0xc06ec000 - 0xc0734c38 ( 292 kB) [ 0.000000] .bss : 0xc0734c5c - 0xc07a4294 ( 446 kB) [ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:114 [ 0.000000] gpiochip_add: registered GPIOs 0 to 31 on device: orion_gpio0 [ 0.000000] gpiochip_add: registered GPIOs 32 to 49 on device: orion_gpio1 [ 0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms [ 0.000000] Console: colour dummy device 80x30 [ 12.788749] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584) [ 12.878682] pid_max: default: 32768 minimum: 301 [ 12.878785] Security Framework initialized [ 12.878803] SELinux: Disabled at boot. [ 12.878850] Mount-cache hash table entries: 512 [ 12.879133] Initializing cgroup subsys cpuacct [ 12.879145] Initializing cgroup subsys devices [ 12.879155] Initializing cgroup subsys freezer [ 12.879163] Initializing cgroup subsys net_cls [ 12.879210] CPU: Testing write buffer coherency: ok [ 12.879426] Setting up static identity map for 0x511040 - 0x51107c [ 12.880083] devtmpfs: initialized [ 12.881449] NET: Registered protocol family 16 [ 12.881946] Kirkwood: MV88F6281-A0, TCLK=200000000. [ 12.881960] Feroceon L2: Cache support initialised. [ 12.886274] bio: create slab <bio-0> at 0 [ 12.886639] vgaarb: loaded [ 12.886905] SCSI subsystem initialized [ 12.887253] usbcore: registered new interface driver usbfs [ 12.887324] usbcore: registered new interface driver hub [ 12.887419] usbcore: registered new device driver usb [ 12.887996] Switching to clocksource orion_clocksource [ 12.913140] NET: Registered protocol family 2 [ 12.913373] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 12.913955] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 12.914055] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 12.914109] TCP: Hash tables configured (established 4096 bind 4096) [ 12.914119] TCP reno registered [ 12.914129] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 12.914152] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 12.914382] NET: Registered protocol family 1 [ 12.914694] RPC: Registered named UNIX socket transport module. [ 12.914705] RPC: Registered udp transport module. [ 12.914713] RPC: Registered tcp transport module. [ 12.914720] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 12.914785] NetWinder Floating Point Emulator V0.97 (double precision) [ 12.915331] audit: initializing netlink socket (disabled) [ 12.915366] type=2000 audit(0.110:1): initialized [ 12.923927] VFS: Disk quotas dquot_6.5.2 [ 12.924158] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 12.926830] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 12.927949] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 12.928525] fuse init (API version 7.18) [ 12.928998] SGI XFS with security attributes, large block/inode numbers, no debug enabled [ 12.930380] msgmni has been set to 238 [ 12.931664] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 12.931678] io scheduler noop registered [ 12.931686] io scheduler deadline registered [ 12.931721] io scheduler cfq registered (default) [ 12.931779] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver [ 12.931815] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver [ 12.968099] mv_xor mv_xor.0: Marvell XOR: ( xor cpy ) [ 13.008077] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy ) [ 13.048068] mv_xor mv_xor.2: Marvell XOR: ( xor cpy ) [ 13.088068] mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy ) [ 13.088408] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 13.108934] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A [ 13.599817] console [ttyS0] enabled [ 13.604413] ONFI flash detected [ 13.607665] ONFI param page 0 valid [ 13.611193] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08AAD) [ 13.618904] Scanning device for bad blocks [ 13.771060] Bad eraseblock 1990 at 0x00000f8c0000 [ 13.780042] 4 cmdlinepart partitions found on MTD device orion_nand [ 13.786333] Creating 4 MTD partitions on "orion_nand": [ 13.791512] 0x000000000000-0x000000100000 : "u-boot" [ 13.797353] 0x000000100000-0x000000500000 : "uImage" [ 13.803185] 0x000000500000-0x000002500000 : "rootfs" [ 13.808933] 0x000002500000-0x000010000000 : "data" [ 13.814788] UBI: attaching mtd2 to ubi0 [ 13.818669] UBI: physical eraseblock size: 131072 bytes (128 KiB) [ 13.824962] UBI: logical eraseblock size: 129024 bytes [ 13.830397] UBI: smallest flash I/O unit: 2048 [ 13.835120] UBI: sub-page size: 512 [ 13.839762] UBI: VID header offset: 512 (aligned 512) [ 13.845619] UBI: data offset: 2048 [ 13.899747] UBI: max. sequence number: 2 [ 13.914295] UBI: attached mtd2 to ubi0 [ 13.918079] UBI: MTD device name: "rootfs" [ 13.923149] UBI: MTD device size: 32 MiB [ 13.928060] UBI: number of good PEBs: 256 [ 13.932697] UBI: number of bad PEBs: 0 [ 13.937152] UBI: number of corrupted PEBs: 0 [ 13.941618] UBI: max. allowed volumes: 128 [ 13.946256] UBI: wear-leveling threshold: 4096 [ 13.950982] UBI: number of internal volumes: 1 [ 13.955438] UBI: number of user volumes: 0 [ 13.959903] UBI: available PEBs: 250 [ 13.964534] UBI: total number of reserved PEBs: 6 [ 13.969260] UBI: number of PEBs reserved for bad PEB handling: 2 [ 13.975294] UBI: max/mean erase counter: 1/1 [ 13.979584] UBI: image sequence number: 0 [ 13.983700] UBI: background thread "ubi_bgt0d" started, PID 41 [ 13.989735] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 13.996627] mv643xx_eth smi: probed [ 14.002278] mv643xx_eth_port mv643xx_eth_port.0: eth0: port 0 with MAC address 00:xx:xx:xx:xx:c6 [ 14.011167] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 14.017768] orion-ehci orion-ehci.0: Marvell Orion EHCI [ 14.023112] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 [ 14.058053] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000 [ 14.078035] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00 [ 14.084047] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 14.090879] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 14.098145] usb usb1: Product: Marvell Orion EHCI [ 14.102869] usb usb1: Manufacturer: Linux 3.3.2-kirkwide ehci_hcd [ 14.109000] usb usb1: SerialNumber: orion-ehci.0 [ 14.114091] hub 1-0:1.0: USB hub found [ 14.117871] hub 1-0:1.0: 1 port detected [ 14.122117] Initializing USB Mass Storage driver... [ 14.127101] usbcore: registered new interface driver usb-storage [ 14.133151] USB Mass Storage support registered. [ 14.138066] mousedev: PS/2 mouse device common for all mice [ 14.143713] i2c /dev entries driver [ 14.147687] device-mapper: uevent: version 1.0.3 [ 14.152677] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com [ 14.161235] cpuidle: using governor ladder [ 14.165423] cpuidle: using governor menu [ 14.170608] TCP cubic registered [ 14.173852] NET: Registered protocol family 17 [ 14.178373] Registering the dns_resolver key type [ 14.183557] registered taskstats version 1 [ 14.188362] console [netcon0] enabled [ 14.192038] netconsole: network logging started [ 14.196584] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 14.202951] Initializing network drop monitor service [ 14.208251] md: Waiting for all devices to be available before autodetect [ 14.215068] md: If you don't use raid, use raid=noautodetect [ 14.221388] md: Autodetecting RAID arrays. [ 14.225507] md: Scanned 0 and added 0 devices. [ 14.229990] md: autorun ... [ 14.232796] md: ... autorun DONE. [ 14.236177] VFS: Cannot open root device "ubi0:rootfs" or unknown-block(0,0) [ 14.243274] Please append a correct "root=" boot option; here are the available partitions: [ 14.251683] 1f00 1024 mtdblock0 (driver?) [ 14.256762] 1f01 4096 mtdblock1 (driver?) [ 14.261856] 1f02 32768 mtdblock2 (driver?) [ 14.266939] 1f03 224256 mtdblock3 (driver?) [ 14.272032] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
Re: Rescue system install on tftp? Need Help October 03, 2012 06:58AM |
Registered: 12 years ago Posts: 501 |
Re: Rescue system install on tftp? Need Help October 04, 2012 10:07AM |
Registered: 11 years ago Posts: 10 |
Re: Rescue system install on tftp? Need Help October 04, 2012 06:36PM |
Registered: 12 years ago Posts: 501 |